Tank Product - Team Poly€¦ · Tank Product Catalogue. 1300 658 96. 1. For occupational health...
2
Tank Product Catalogue 1300 658 961 For occupational health and safety reasons there must be a sufficient number of adult able bodied persons available to assist the driver with delivery of your tank (refer table below). Customers should also be aware that insufficient labour on site may delay delivery or incur additional delivery costs. Delivery of your Team Poly water tank When ordering large Team Poly Water Tanks, 9,000L and above, please complete the following checklist. 1. Delivery site / access free from overhead obstruction (e.g. Overhanging tree branches or power lines) 7 metres high minimum clearance and flat level access. 2. Sufficient parking and turning area for the truck and trailer (30 metres long, 7 metres high and 5 metres wide). 3. Ground surface flat, firm and dry to avoid the truck or trailer sinking or shifting during delivery. 4. Identify and advise Team Poly of any hazardous or unsafe work environment conditions on site. 1 person Tanks up to and including 9,000L (includes Slimlines) 2,000 gallons 2 people 13,500 litre 3,000 gallons 3 people 22,500 – 27,00 litres 5,000 – 6,000 gallons 4 people 40,950 – 50,050 litres 9,000 – 11,000 gallons NUMBER OF ADULT PEOPLE REQUIRED (excluding the Team Poly driver) LITRES GALLONS Recommended Site Preparation Correct site preparation is essential to ensure a long and trouble- free life for your tank. It is essential to have your water tank on a FLAT LEVEL COMPACTED BASE. The base of your water tank must be fully supported at all times. Concrete slab Concrete slab must be at least 25mpa and 100mm (4") thick with F62 mesh halfway through the mix. It should be screeded flat and level with no high or low spots. The finished surface should have a trowelled finish. Crusher dust Crusher dust bases must be 150mm (6") wider than diameter of the water tank and prepared as follows: • Remove at least 100mm (4") of natural earth, ensuring the base is flat and level. • Refill with at least 75mm (3") of crusher dust thoroughly mixed with dry cement powder for a 4m (13') base we suggest 2-3 bags of cement powder. • Once spread, thoroughly compact the crusher dust with suitable compacting equipment, not by any other means. • Thoroughly screed the surface and ensure the finished surface is perfectly FLAT AND LEVEL and free of stones, tree roots, etc. Do not water to set the cement powder, natural moisture will do this when your tank is in position. Note: Sand is not acceptable. Inspect the base regularly checking for and rectifying any undermining by water run-off or animals burrowing such as toads and mice. Molasses tanks Molasses tanks must have a concrete slab or suitably constructed tank stand with flat level deck to be considered for warranty. Fatigue Management Policy Team Poly is committed to meeting our duty of care under the Chain of Responsibility and Compliance and Enforcement Legislation. Activities that may contribute to a breach include, but is not limited to: • Exerting pressure on drivers to overload or speed. • Placing unrealistic delivery time frames on drivers. • Accepting overloaded trailers. • Accepting inadequate restrained loads. • Delays during loading and unloading. With the support and co-operation of all parties, we can ensure we all work towards improving safety while encouraging a culture of compliance and continuous improvement in the transport industry. Team Poly Tanks Pty Ltd. ABN 79 162065778 30 Waddikee Rd, Lonsdale SA 5160 1300 658 961 www.teampoly.com.au Disclaimer This brochure is designed to provide readers with an introduction to Team Poly products. Because of changes in conditions and circumstances, Team Poly Tanks reserve the right and at any time and without notice to discontinue or change the features, designs, materials, colours, specifications and prices of its products and to either permanently or temporarily withdraw any such products from the market without incurring any liability to a prospective purchaser. Details referred to in this brochure are based on pre production specifications and could be altered or deleted prior to the products sale date. As variations that occur in the manufacturing of products, all capacities, measurements, dimensions and weights quoted should be taken as approximate only and are subject to change. Team Poly Tanks reserve the right to discontinue or change any of the tank colours at any time and without notice. Every effort has been made to depict the colours as realistically as possible in the brochure however some variations may occur due to the printing limitations. TP7170 Base must be 150mm (6") wider than tank. Overflow must be piped away from base to prevent undermining. 3-4" (75-100mm) of compacted crusher dust or concrete pad. Boxing beams Support Polypipe Outlet Gate valve Agent Warranty *See the Team Poly website for details of the warranty. www.teampoly.com.au Li-Lo Underground Water Tanks Pumps and Water Tank Accessories Septic Tanks Underdeck Tanks Industrial Molasses Tanks Excavation approx 31m 3 / 1095ft 3 1,500L 3,000L 5,000L Length 2,100mm 2,450mm 2,890mm Width 1,250mm 2,100mm 2,300mm Height of tank collar 700mm 735mm 950mm Height of dome collar 315mm 315mm 315mm Weight 80kgs 170kgs 240kgs 1,000L - 22,500L • Established national distribution service. • Manufacturing sites in Queensland, New South Wales, Victoria and South Australia. • Tanks designed and manufactured to align specific industrial requirements. • Full range of fittings and attachments fitted to your specifications. We offer a specialised consulting service for the supply of custom- fitted industrial tanks for a range of applications in the market sectors of industrial liquid storage, chemical storage, liquid feed and fertiliser. 75 % less digging compared with a concrete cistern. Save more than 100 wheelbarrow loads of soil! Excavation approx 7.6m 2 / 268ft 3 1,500L 5,000L 3,000L www.teampoly.com.au 1000L 2000L HEIGHT: 620mm WIDTH: 1,225mm LENGTH: 2,420mm HEIGHT: 960mm WIDTH: 1,225mm LENGTH: 2,420mm 3,000L LENGTH: 2,300mm WIDTH: 1,600mm HEIGHT: 1,700mm Team Poly recommend Davey and ClayTech pumps. TOP MOUNT RAINBANK KIT · Top Mount kit includes 2 stage submersible pump and fittings · Mounted to the top of the tank for safety and security · Hinged lid for easy maintenance access · Connections must be fitted by a licensed plumber 1,000 Litre Cartage Tanks SIZES 200L - 1,000L • All Tanks 500L and above are baffled • All tanks feature sump • Tank feature moulded 50mm Outlet • Screw on lid and breather are provided • 5 year pro rata warranty (tank only) Length Width Height 200L 990mm 610mm 750mm $ 300L 1380mm 610mm 750mm $ 500L 1280mm 820mm 940mm $ 1000L 1530mm 1200mm 1060mm $
Transcript of Tank Product - Team Poly€¦ · Tank Product Catalogue. 1300 658 96. 1. For occupational health...
Tank Product Catalogue
1300 658 961
For occupational health and safety reasons there must be a sufficient number of adult able bodied persons available to assist the driver with delivery of your tank (refer table below). Customers should also be aware that insufficient labour on site may delay delivery or incur additional delivery costs.
Delivery of your Team Poly water tankWhen ordering large Team Poly Water Tanks, 9,000L and above, please complete the following checklist.
1. Delivery site / access free from overhead obstruction (e.g. Overhanging tree branches or power lines) 7 metres high minimum clearance and flat level access.
2. Sufficient parking and turning area for the truck and trailer (30 metres long, 7 metres high and 5 metres wide).
3. Ground surface flat, firm and dry to avoid the truck or trailer sinking or shifting during delivery.
4. Identify and advise Team Poly of any hazardous or unsafe work environment conditions on site.
1 person Tanks up to and including 9,000L (includes Slimlines) 2,000 gallons
2 people 13,500 litre 3,000 gallons
3 people 22,500 – 27,00 litres 5,000 – 6,000 gallons
4 people 40,950 – 50,050 litres 9,000 – 11,000 gallons
NUMBER OF ADULT PEOPLE REQUIRED (excluding the Team Poly driver) LITRES GALLONS
Recommended Site PreparationCorrect site preparation is essential to ensure a long and trouble-free life for your tank.It is essential to have your water tank on a FLAT LEVEL COMPACTED BASE. The base of your water tank must be fully supported at all times.Concrete slabConcrete slab must be at least 25mpa and 100mm (4") thick with F62 mesh halfway through the mix. It should be screeded flat and level with no high or low spots. The finished surface should have a trowelled finish.Crusher dustCrusher dust bases must be 150mm (6") wider than diameter of the water tank and prepared as follows:• Remove at least 100mm (4") of natural earth, ensuring the base is
flat and level.• Refill with at least 75mm (3") of crusher dust thoroughly mixed with
dry cement powder for a 4m (13') base we suggest 2-3 bags of cement powder.
• Once spread, thoroughly compact the crusher dust with suitable compacting equipment, not by any other means.
• Thoroughly screed the surface and ensure the finished surface is perfectly FLAT AND LEVEL and free of stones, tree roots, etc. Do not water to set the cement powder, natural moisture will do thiswhen your tank is in position.
Note: Sand is not acceptable.Inspect the base regularly checking for and rectifying any undermining by water run-off or animals burrowing such as toads and mice.Molasses tanksMolasses tanks must have a concrete slab or suitably constructed tank stand with flat level deck to be considered for warranty.
Fatigue Management PolicyTeam Poly is committed to meeting our duty of care under the Chain of Responsibility and Compliance and Enforcement Legislation.Activities that may contribute to a breach include, but is not limited to:• Exerting pressure on drivers to overload or speed.• Placing unrealistic delivery time frames on drivers.• Accepting overloaded trailers.• Accepting inadequate restrained loads.• Delays during loading and unloading.With the support and co-operation of all parties, we can ensure we all work towards improving safety while encouraging a culture of compliance and continuous improvement in the transport industry.
Team Poly Tanks Pty Ltd. ABN 79 162065778 30 Waddikee Rd, Lonsdale SA 51601300 658 961www.teampoly.com.au
Disclaimer This brochure is designed to provide readers with an introduction to Team Poly products. Because of changes in conditions and circumstances, Team Poly Tanks reserve the right and at any time and without notice to discontinue or change the features, designs, materials, colours, specifications and prices of its products and to either permanently or temporarily withdraw any such products from the market without incurring any liability to a prospective purchaser. Details referred to in this brochure are based on pre production specifications and could be altered or deleted prior to the products sale date. As variations that occur in the manufacturing of products, all capacities, measurements, dimensions and weights quoted should be taken as approximate only and are subject to change. Team Poly Tanks reserve the right to discontinue or change any of the tank colours at any time and without notice. Every effort has been made to depict the colours as realistically as possible in the brochure however some variations may occur due to the printing limitations. TP7170
Base must be 150mm (6") wider than tank.
Overflow must be piped away from base to prevent undermining.
3-4" (75-100mm) of compacted crusher dust or concrete pad.
Boxing beams
Support
Polypipe
Outlet
Gate valve
Agent
Warranty*See the Team Poly website for details of the warranty. www.teampoly.com.au
Li-Lo Underground Water Tanks
Pumps and Water Tank Accessories
Septic Tanks
Underdeck Tanks
Industrial Molasses Tanks
Excavation approx 31m3 / 1095ft3
1,500L 3,000L 5,000L
Length 2,100mm 2,450mm 2,890mm
Width 1,250mm 2,100mm 2,300mm
Height of tank collar 700mm 735mm 950mm
Height of dome collar 315mm 315mm 315mm
Weight 80kgs 170kgs 240kgs
1,000L - 22,500L• Established national
distribution service.• Manufacturing sites in
Queensland, New SouthWales, Victoria andSouth Australia.
• Tanks designed andmanufactured toalign specific industrialrequirements.
• Full range of fittings andattachments fitted to yourspecifications.
We offer a specialised consulting service for the supply of custom-fitted industrial tanks for a range of applications in the market sectors of industrial liquid storage, chemical storage, liquid feed and fertiliser.
75% less digging compared with a concrete cistern.Save more than 100 wheelbarrow loads of soil!
Excavation approx 7.6m2 / 268ft3
1,500L
5,000L
3,000L
www.teampoly.com.au
1000L 2000LHEIGHT: 620mmWIDTH: 1,225mmLENGTH: 2,420mm
HEIGHT: 960mmWIDTH: 1,225mmLENGTH: 2,420mm
3,000LLENGTH: 2,300mmWIDTH: 1,600mmHEIGHT: 1,700mm
Team Poly recommend Davey and ClayTech pumps.
TOP MOUNT RAINBANK KIT
· Top Mount kit includes 2 stage submersible pump and fittings
· Mounted to the top of the tank for safety and security
· Hinged lid for easy maintenance access
· Connections must be fitted by a licensed plumber
1,000 Litre
Cartage Tanks
SIZES 200L - 1,000L
• All Tanks 500L and above are baffled• All tanks feature sump• Tank feature moulded 50mm Outlet• Screw on lid and breather are provided• 5 year pro rata warranty (tank only)
Length Width Height
200L 990mm 610mm 750mm $300L 1380mm 610mm 750mm $500L 1280mm 820mm 940mm $1000L 1530mm 1200mm 1060mm $
Team Poly is an Australian owned company which has been making water tanks and associated polyethylene products since 1991 and is part of the National Poly Industries Group, Australia’s largest supplier of water tanks.
Team Poly offer a wide range of water solutions.Round tanks from 545L to 50,050L, industrial tanks, slimline tanks, underground tanks, cartage tanks, troughs and a choice of water tank accessories and pumps.Team Poly offer a wide range of styles from traditional corrugated tanks to the ultra modern range of Boabab tanks.
Why buy a Team Poly Tank?• Team Poly tanks are made from pure
Australian food grade polyethylene.• Over 20 years of experience in
manufacturing water tanks.• Tanks are manufactured and certified to
the Australian standard, AS4766.• 14 Colorbond® tank colours to complement
houses, sheds, fences or any other structure.• 25 year pro rata warranty on all round tanks.*
1,000L (220G)
DIAMETER: 900mmINLET HEIGHT: 2,020mmOVERALL HEIGHT: 2,020mm
PRICE $
900L (200G) SL2 1,000L (220G)
DIAMETER: 1,150mmINLET HEIGHT: 1,165mmOVERALL HEIGHT: 1,165mm
DIAMETER: 850mmINLET HEIGHT: 1,900mmOVERALL HEIGHT: 1,900mm
PRICE $ PRICE $
Round/Traditional Tanks545L (120G)
DIAMETER: 700mmINLET HEIGHT: 1,775mmOVERALL HEIGHT: 1,775mm
PRICE $
50,050L (11,000G)
DIAMETER: 4,400mmINLET HEIGHT: 3,030mmOVERALL HEIGHT: 3,420mm
PRICE $
5,400L (1200G)
DIAMETER: 2,000mmINLET HEIGHT: 2,030mmOVERALL HEIGHT: 2,190mm
PRICE $
4,500L Squat (1000G)
DIAMETER: 2,250mmINLET HEIGHT: 1,460mmOVERALL HEIGHT: 1,550mm
PRICE $
9,000L Tall (2000G)
DIAMETER: 2,570mmINLET HEIGHT: 2,180mmOVERALL HEIGHT: 2,300mm
PRICE $
1,600L (350G)
DIAMETER: 1,220mmINLET HEIGHT: 1,825mmOVERALL HEIGHT: 1,825mm
PRICE $
2,300L (500G)
DIAMETER: 1,720mmINLET HEIGHT: 1,365mmOVERALL HEIGHT: 1,365mm
PRICE $
Modular Flat2,000L
WIDTH: 1,950mmHEIGHT: 2,000mmDEPTH: 600mm
PRICE $
2,500L
WIDTH: 2,400mmHEIGHT: 2,000mmDEPTH: 600mm
PRICE $
4,500L Tall (1000G)
DIAMETER: 1,830mmINLET HEIGHT: 1,995mmOVERALL HEIGHT: 2,120mm
PRICE $
PRICE $
3,000L (650G)
DIAMETER: 1,440mmINLET HEIGHT: 2,260mmOVERALL HEIGHT: 2,260mm
27,000L (6,000G)
DIAMETER: 3,970mmINLET HEIGHT: 2,570mmOVERALL HEIGHT: 2,750mm
PRICE $
22,500L Tall (5,000G)
DIAMETER: 3,530mmINLET HEIGHT: 2,530mmOVERALL HEIGHT: 2,670mm
PRICE $
PRICE $
13,500L (3000G)
DIAMETER: 2,805mmINLET HEIGHT: 2,360mmOVERALL HEIGHT: 2,580mm
9,000L Squat (2000G)
DIAMETER: 2,890mmINLET HEIGHT: 1,570mmOVERALL HEIGHT: 1,900mm
PRICE $
22,500L Squat (5,000G)
DIAMETER: 3,730mmINLET HEIGHT: 2,410mmOVERALL HEIGHT: 2,580mm
PRICE $
5,000L
WIDTH: 3,300mmHEIGHT: 2,100mmDEPTH: 1,050mm
PRICE $
Urban Slimline
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
Razor Slimlines1,000L
WIDTH: 2,400mmHEIGHT: 1,935mmDEPTH: 290mm
PRICE $ PRICE $
1,000L Stubby
WIDTH: 1,200mmHEIGHT: 1,935mmDEPTH: 560mm
PRICE $
2,000L
WIDTH: 2,400mmHEIGHT: 1,935mmDEPTH: 560mm
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
40,950L (9,000G)
DIAMETER: 4,400mmINLET HEIGHT: 2,420mmOVERALL HEIGHT: 2,800mm
PRICE $
Delivery zones apply. Not in SA.
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
8,000L (1800G)
PRICE $
DIAMETER: 2,350mmINLET HEIGHT: 2,110mmOVERALL HEIGHT: 2,200mm
Modular Corrugated1,500L
WIDTH: 1,800mmHEIGHT: 2,000mmDEPTH: 500mm
PRICE $
2,500L
WIDTH: 2,400mmHEIGHT: 2,000mmDEPTH: 600mm
PRICE $
1,140L
WIDTH: 1,800mmHEIGHT: 1,570mmDEPTH: 500mm
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
PRICE $
3000L
TOP DIAMETER: 1,845mmBOTTOM DIAMETER: 1,600mmOVERALL HEIGHT: 1,520mm
PRICE $
10,000L
TOP DIAMETER: 3,060mmBOTTOM DIAMETER: 2,730mmOVERALL HEIGHT: 2,190mm
PRICE $
Boabab Rainwater Tanks1000L
TOP DIAMETER: 1,115mmBOTTOM DIAMETER: 860mmOVERALL HEIGHT: 1,495mm
PRICE $
TOP DIAMETER: 2,140mmBOTTOM DIAMETER: 1,860mmOVERALL HEIGHT: 1,805mm
PRICE $
5000L YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
Aqua Spring Range
3,000L
WIDTH: 2,500mmHEIGHT: 2,000mmDEPTH: 750mm
PRICE $
3,500L
WIDTH: 2,650mmHEIGHT: 2,230mmDEPTH: 800mm
PRICE $
650L
WIDTH: 1,090mmHEIGHT: 1,780mmDEPTH: 500mm
PRICE $
1,600L
WIDTH: 1,520mmHEIGHT: 2,100mmDEPTH: 700mm
PRICE $
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA 1000L
WIDTH: 1150mmHEIGHT: 2,000mmDEPTH: 550mm
PRICE $
Team Poly’s standard range is available in the following colours:
Also available in:
Bronze Olive, Gull Grey, Evening Haze, Monument and Sand Bank
BlackSlate Grey
Jasper Mountain Blue
Beige Birch Grey
Heritage Red
Heritage Green
MerinoMist Green
RivergumWhite WheatSmooth Cream
Rotathene® SUPA UV is at the forefront of UV protection technology. The UV stabilizer is evenly distributed through the Polymer and specified for tanks made in accordance
with AS/NZS 4766:2006 standards.
ROTATHENE® SUPA UV
Making tanks built to last
22,500L
DIAMETER: 3,530mmINLET HEIGHT: 2,530mmOVERALL HEIGHT: 2,880mm
PRICE $
NEW RELEASE
YEAR PRO RATAYEAR PRO RATAYEAR PRO RATA
2000L
WIDTH: 670mmHEIGHT: 1960mmDEPTH: 2200mm
PRICE $
