Table of Contents Specialty Products Solutions Catalog.pdfez flat aq 39 ez flat 20 ba 40 ez flat...
Transcript of Table of Contents Specialty Products Solutions Catalog.pdfez flat aq 39 ez flat 20 ba 40 ez flat...
Table of Contents
Eagle Specialty Products Solutions Catalog
Solutions 4
Pigment DispersionsColor Selection Guide 5Color Compatibility Chart 6WB Dispersions 7AD Dispersions 9HP Dispersions 11XVOC Dispersions 13Toners For White Products 14
Specialty Additives Specialty Additives Product Guide 15SUPERSPERSE® 95 17SUPERSPERSE® 100 19SUPERSPERSE® 200 20SUPERSPERSE® E-ONE 21SUPERSPERSE® E-TWO 22SUPERSPERSE® E-THREE 23SUPERSPERSE® 1000 24SUPERSPERSE® 3000 25SUPERSPERSE® AD 26SUPERSPERSE® DRY 27SUPERSPERSE® EM-40 28
FixersFX 1 29FX 2 30FX 3 31FX 4 32
DefoamersFB 100 33FB 200 34FB 500 35FB S-40 36
Last Revised 3/16/2015
Table of ContentsDriers To Replace Cobalt
SUPER DRY 1000 37SUPER DRY WB99 38
Flatting PastesEZ FLAT AQ 39 EZ FLAT 20 BA 40EZ FLAT A-100 41EZ FLAT W-30 42EZ FLAT 20 MS 43
WaxesSUPERSLIP 35 44 SUPERSLIP 41 45SUPERSLIP 45 46SUPERSLIP EX 47
ThickenersEZ GEL 15A100 48 EZ GEL 15nBA 49EZ GEL 15X 50EZ GEL MS 51EZ GEL NOVOC TBA 52EZ GEL W 16 53
Specialty Oils#1 CASTOR OIL 54T 31® CASTOR OIL 55T 41 CASTOR OIL 56T 95 CASTOR OIL 57T 500 CASTOR OIL 58MS PASTE 59
Last Revised 3/16/2015
Manufacturing:
• Pigment dispersions and specialty additives (aqueous and solventborne) for paints, coatings, caulks, inks and adhesives
• Castor oil, low moisture, urethane-grade castor oil, polyols and prepolymers• Castor based thickeners and moisture scavengers • Custom design and toll manufacturing
Warehousing:
• 435,000 square feet of storage • Climate controlled and sprinkler system equipped • Hazardous and flammable materials equipped • Drum filling available
Distribution: Raw Materials:
• Oils: Linseed, Tung and Lecithin • Paraffin Wax: 125 Melt Point • Hard Resins: Hydrocarbon, Maleic and Phenolic• Fine Pigment Extenders: Barium Sulfate and Zinc Sulfide
Containers:
• New and reconditioned steel 30 and 55 gallon drums• New and reconditioned plastic 30 and 55 gallon drums• Cleveland Steel Containers• Full line of steel pails• Full line of Norton Plastic Pails• New and reconditioned 275 gallon totes
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
SOLUTIONS
Samples of products are available upon request
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
PIGMENT DISPERSIONSCOLOR SELECTION GUIDE
Pigment Color Index Number WB AD HP XVOCRUTILE TiO2 WH6 77891 1106 2106 0106RUTILE TiO2 MAX CHALK RESISTANCE WH6 77891 3106TRANSPARENT YELLOW OXIDE Y42 77492 1350 2300/2335 3350 0300ORGANIC YELLOW (RS) Y139 N/A 13139 33139LIGHT ORGANIC YELLOW Y151 13980 13151 33151 03175LIGHT LEMON YELLOW OXIDE Y42 77492 1342 2342 3342 0342L/F MEDIUM YELLOW Y151/Y83 13980/21108 0315183HANSA YELLOW (RS) Y 65 1365 2365HANSA YELLOW Y73 11738 23483HS HANSA YELLOW Y74 11741 13700HANSA YELLOW (GS) Y74 2374ORGANIC YELLOW MEDIUM Y65/Y74 11740/11741 13490 23490ORGANIC YELLOW-PRIMROSE Y97 11767 1397DIARYLIDE ORANGE OR34 21115 1434 3434L/F ORANGE OR34/OR36 21115/11780 043436DNA ORANGE R4/12085 OR5 1405R 2405TRANSPARENT RED OXIDE R101 77491 1550 2500 3550 0500RED OXIDE LIGHT R101 77491 15101 25101 35101 05102RED OXIDE MEDIUM R101 77491 15102 25102RED OXIDE DARK R101 77491 35103LIGHT ORGANIC RED R170 12475 15172 35172MONO AZO RED R170 12475 05173DEEP ORGANIC RED R170 12475 15175 25175 35175QUINACRIDONE RED V19 46500 1519 3519 0519BON RED LIGHT R48 15865BON MAROON R52.2 15860 35522 05522PHTHALO GREEN GR7 74260 167 267 367 067PHTHALO GREEN (YS) GR36 74265 1636 3636BURNT SIENNA BR7 77491 177 277BURNT UMBER BR7 77491 1711 2711 3711 0711RAW UMBER BR7 77491 1700 2700 3700B 0700VAN DYKE BROWN N/A N/A 27516PHTHALO BLUE B15.1 18151PHTHALO BLUE (RS) B15.2 74160 18152 28152 38152PHTHALO BLUE NFNC B15.2 74160 2800 3800PHTHALO BLUE (GS) B15.4 74160 18154 28154 38154PHTHALO BLUE PB B15.2/B15.4 74160 0815254QUINACRIDONE VIOLET V19 46500 1819 2819 3819 0819CARBAZOLE VIOLET V23 51319 1823 2823S 3823TINTING BLACK BK7 77266 197T 297T 397T 097HI STRENGTH TINTING BLACK BK7 29329MASSTONE BLACK BK7 77266 1900M 2900M 3921M/
3955M0900
MASSTONE BLACK, HIGH JETNESS BK7 77266 3900M
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
PIGMENT DISPERSIONSCOLOR COMPATIBILITY CHART
Aqueous Emulsion (Latex) WB AD HP XVOCACRYLIC YES
VINYL ACRYLIC YES
VINYL ACETATE YES
STYRENE BUTADIENEEPOXY YES
POLYURETHANE (PUD) YES
Water ReducibleACRYLIC YES
ALKYD YES
POLYESTER YES
EPOXY YES
SolventborneLONG OIL ALKYD YES YES
MEDIUM OIL ALKYD YES YES
SHORT OIL ALKYD YES YES YES
VINYL TOLUENE ALKYD YES YES
CHAIN STOPPED ALKYD YES YES
STYRENATED ALKYD YES YES
SILICONE ALKYD YES YES
BODIED OIL YES
OIL MODIFIED URETHANE YES
ALKYD MODIFIED URETHANE YES YES
TWO COMPONENT URETHANE YES YES
POLYESTER YES YES YES
VINYL YES
VINYL ACRYLIC YES YES
ACRYLIC YES YES
NITROCELLULOSE YES YES YES
CELLULOSE ACETATE BUTYRATE YES YES
TWO COMPONENT EPOXY YES YES
EPOXY ESTER YES YES YES
CHLORINATED RUBBER YES
ALKYD UREA YES YES YES
ALKYD MELAMINE YES YES YES
HYDROCARBON YES
PHENOLIC YES
SERIES 2000 WB DISPERSIONS are liquid pigment dispersion concentrates for tinting and masstone applications. They are freeze-thaw stable and will not support growth of micro-organisms. WB Dispersions have excellent compatibility in a wide range of waterborne coatings including emulsions, solutions and aqueous dispersions. WB Dispersions have little effect on gloss, dry time and resistance properties.
Vehicle: Based on SUPERSPERSE 100 and SUPERSPERSE 200.
Solvent: Based on water and Propylene Glycol.
Technical Data:% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
WB 1106 RUTILE TiO2 WH6 17.80 2.14 69.5 5.1 25.4 37.0 9.9 53.1 2.06 247
WB 1350 TRANSPARENT YELLOW OXIDE Y42 10.80 1.30 32.0 16.0 52.0 21.0 10.3 68.7 2.25 270
WB 13139 ORGANIC YELLOW (RS) Y83 9.30 1.12 30.0 4.0 66.0 22.2 4.0 73.8 2.08 250
WB 13151 LT. ORGANIC YELLOW Y151 9.33 1.12 35.0 4.2 60.8 26.0 4.4 69.6 1.73 208
WB 1342 LT. LEMON YELLOW OXIDE Y42 15.60 1.87 60.0 5.2 34.8 27.0 8.3 64.7 1.77 212
WB 13490 ORGANIC YELLOW MEDIUM Y65/Y74 9.82 1.18 38.0 5.0 57.0 30.0 6.0 64.0 1.62 193
WB 1365 LEAD FREE YELLOW Y65 10.26 1.23 41.2 7.1 52.3 32.2 7.8 60.0 1.54 185
WB 13700 HS HANSA YELLOW Y74 9.35 1.12 35.6 4.0 60.4 28.4 5.3 66.3 1.72 207
WB 1397 ORGANIC YEL PRIMROSE Y97 9.60 1.15 50.0 8.0 42.0 45.0 6.0 49.0 2.84 341
WB 1405R DNA ORANGE O5 9.66 1.16 37.3 6.7 56.0 27.8 6.9 65.3 2.47 296
WB 1434 DIARYLIDE ORANGE OR34 9.55 1.15 39.5 6.9 53.6 32.0 6.8 61.2 1.77 200
WB 1550 TRANSPT. RED OXIDE R101 11.66 1.40 35.0 16.0 49.0 21.0 10.3 68.7 2.66 320
WB 15101 RED IRON OXIDE LIGHT R101 16.30 1.96 60.0 6.0 34.0 24.0 10.0 66.0 2.03 243
WB 15102 RED IRON OXIDE MEDIUM R101 16.14 1.94 60.0 6.0 34.0 25.0 9.8 65.2 2.03 243
WB 15122 QUINACRIDONE MAGENTA V19 9.13 1.10 28.6 14.0 57.4 21.4 11.3 66.6 3.58 429
WB 15172 LIGHT ORGANIC RED R170 9.20 1.10 29.4 4.5 66.1 23.9 4.1 72.0 2.06 247
WB 15175 DEEP ORGANIC RED R170 9.10 1.09 27.7 7.4 64.9 22.2 8.0 69.8 2.00 240
WB 15188 ORGANIC SCARLET R188 9.24 1.11 30.1 5.2 64.7 23.0 5.0 72.0 5.96 714
PIGMENT DISPERSIONS: WBWATERBORNE DISPERSIONS FOR AQUEOUS SYSTEMS (1/2)
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
WB 1519 QUINACRIDONE RED V19 9.30 1.12 25.0 6.5 68.5 18.7 22.1 59.2 1.26 151
WB 15254 DPP RED R254 9.86 1.18 40.0 10.0 50.0 30.5 10.0 59.5 0.08 9.31
WB 1636 PHTHALO GREEN (YS) GR36 10.63 1.28 32.0 6.3 61.7 15.8 6.9 77.3 2.97 356
WB 167 PHTHALO GREEN GR7 10.10 1.21 37.2 6.3 56.5 23.0 6.7 70.3 1.99 239
WB 1700 RAW UMBER BR7 13.00 1.56 50.0 4.3 45.7 23.9 4.5 71.6 2.06 247
WB 1711 BURNT UMBER BR7 11.87 1.42 40.7 3.7 55.6 17.5 3.6 78.9 2.08 249
WB 177 BURNT SIENNA BR7 13.00 1.56 53.4 3.9 42.7 28.6 3.8 67.6 1.99 239
WB 18151 PHTHALO BLUE (RS) B15.1 10.80 1.30 36.3 7.2 56.0 26.1 7.3 67.2 2.22 266
WB 18152 PHTHALO BLUE B15.2 10.06 1.21 30.5 6.5 63.0 21.6 6.4 72.0 1.93 231
WB 18154 PHTHALO BLUE (GS) B15.4 9.60 1.15 30.0 5.9 64.1 20.7 5.8 73.5 2.04 245
WB 1819 QUINACRIDONE VIOLET V19 9.50 1.14 25.0 5.0 70.0 31.0 5.0 64.0 2.31 276.5
WB 1823 CARBAZOLE VIOLET V23 9.16 1.10 17.7 5.9 76.4 12.6 5.5 81.9 2.01 241
WB 1900M MASSTONE BLACK BK7 8.90 1.07 30.1 7.2 62.7 19.6 8.0 72.4 2.09 250
WB 1999M HI-JET MASSTONE BLACK BK7 8.99 1.08 9.0 12.7 78.3 5.4 10.0 84.6 3.54 425
WB 197T TINTING BLACK BK7 9.82 1.18 32.6 5.3 62.1 21.3 6.0 72.7 1.97 236
WB EX258D TONER FOR WHITE 8.55 1.03 2.5 0.6 96.9 2.0 0.2 97.8 4.08 490
PIGMENT DISPERSIONS: WBWATERBORNE DISPERSIONS FOR AQUEOUS SYSTEMS (2/2)
SERIES 2000 AD DISPERSIONS are liquid pigment dispersion concentrates for tinting and masstone applications. AD Dispersions have exceptional compatibility in a wide range of solvent coatings.
Vehicle: Proprietary modified Long Oil Alkyd
Solvent: Mineral Spirits
Technical Data:% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
AD 2106 RUTILE TiO2 WH6 15.60 1.87 65.0 22.0 13.0 29.6 39.0 31.4 2.03 243
AD 2300 TRANSPARENT YELLOW OXIDE Y42 9.50 1.14 31.5 30.5 38.0 9.2 34.8 56.0 3.60 433
AD 2335 TRANSPARENT YELLOW OXIDE Y42 10.14 1.22 36.0 31.5 32.5 12.0 37.9 50.1 3.29 394
AD 2342 LT. LEMON YELLOW OXIDE Y42 14.00 1.68 60.0 20.0 20.0 24.7 31.9 43.4 2.80 336
AD 2365 LEAD FREE YELLOW Y65 9.28 1.11 44.2 20.1 35.7 28.2 24.8 47.0 3.31 397
AD 2374 HANSA YELLOW Y74 8.20 0.99 30.0 30.0 40.0 20.0 29.2 50.8 3.28 393
AD 23483 HANSA YELLOW GS Y73 8.45 1.01 30.7 36.3 33.0 21.0 36.0 43.0 2.83 339
AD 23490 ORGANIC YELLOW MEDIUM Y74/11741 9.17 1.10 40.0 24.8 35.2 23.4 28.4 48.2 3.20 383
AD 2405 DNA ORANGE O5 9.28 1.11 42.0 33.4 24.6 29.7 38.5 31.8 2.33 279
AD 2500 TRANSPARENT RED OXIDE R101 10.03 1.20 35.0 28.3 36.7 10.2 34.4 55.4 3.68 441
AD 2503 TOLUIDINE RED R3 8.55 1.03 35.0 30.0 35.0 25.0 30.0 45.0 2.99 359
AD 25101 RED OXIDE LIGHT R101 15.50 1.86 60.0 25.0 15.0 21.7 42.3 36.0 2.33 279
AD 25102 RED OXIDE MEDIUM R101 15.60 1.88 63.0 20.0 17.0 24.1 34.8 41.1 2.65 318
AD 25122 QUINACRIDONE MAGENTA R122 7.67 0.92 22.0 21.8 56.2 14.1 19.8 66.1 4.31 517
AD 25175 DEEP ORGANIC RED R170 8.30 1.00 30.0 37.0 33.0 22.0 35.5 42.5 2.74 329
AD 2636 PHTHALO GREEN YS GR36 8.78 1.05 24.0 38.5 37.5 10.7 4.5 84.8 3.29 395
AD 267 PHTHALO GREEN GR7 8.86 1.06 27.6 38.2 34.2 14.4 39.0 46.6 3.03 362
AD 2700 RAW UMBER BR7 11.80 1.44 50.0 22.0 28.0 21.2 27.6 51.2 3.30 396
AD 2711 BURNT UMBER BR7 12.50 1.44 50.0 22.0 28.0 17.3 28.4 54.3 3.50 420
PIGMENT DISPERSIONS: ADALKYD DISPERSIONS FOR SOLVENTBORNE SYSTEMS (1/2)
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
AD 27504 RAW SIENNA Y43 12.34 1.48 50.9 29.2 19.9 20.9 41.3 37.8 2.46 295
AD 27516 VAN DYKE BROWN (NAT/SYN) N/A 9.32 1.12 36.8 31.5 31.7 20.7 34.9 44.4 2.96 354
AD 277 BURNT SIENNA BR7 13.00 1.56 50.0 33.0 17.0 21.7 44.0 34.3 2.20 265
AD 2800 PHTHALO BLUE NFNC B15.2 8.40 1.01 22.0 39.0 39.0 13.9 35.3 50.8 3.28 393
AD 28152 PHTHALO BLUE RS B15.2 8.30 1.00 21.0 35.0 44.0 13.2 30.0 56.8 3.65 438
AD 28154 PHTHALO BLUE GS B15.4 8.40 1.01 29.5 34.6 35.8 21.9 32.7 45.4 2.98 358
AD 2819 QUINACRIDONE VIOLET V19 8.10 0.97 22.0 42.0 36.0 13.8 40.7 45.5 2.90 350
AD 2823S CARBAZOLE VIOLET V23 7.70 0.92 18.0 30.6 51.4 11.2 28.1 60.7 4.00 478
AD 2900M MASSTONE BLACK BK7 8.30 1.00 22.0 36.0 42.0 12.5 33.5 54.0 3.49 418
AD 29329 HI STRENGTH TINTING BLACK BK7 8.44 1.01 23.6 35.5 40.9 13.3 35.3 51.4 3.45 414
AD 297T TINTING BLACK BK7 8.60 1.03 28.0 33.0 39.0 16.5 31.5 52.0 6.19 743
EX 319 TONER FOR WHITE 7.95 0.95 3.0 69.1 27.9 2.0 63.6 34.4 3.06 367
EX 657-1 DNA ORANGE O5 9.23 1.11 42.0 33.1 24.9 29.8 38.2 32.0 2.31 276
PIGMENT DISPERSIONS: ADALKYD DISPERSIONS FOR SOLVENTBORNE SYSTEMS (2/2)
SERIES 2000 HP DISPERSIONS are liquid pigment dispersion concentrates for tinting and masstone applications. They are compatible with most high-performance solventborne systems. All pigments used in HP Dispersions exhibit lightfastness, heat resistance and bleed resistance properties.
Vehicle: Modified thermoplastic acrylic
Solvent: Blend of PM Acetate and Aromatic 100
Technical Data:% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
HP 3106 NON-CHALKING TiO2 WH6 15.82 1.92 65.0 15.0 20.0 31.3 26.7 42.0 3.21 384
HP 3350 TRANSPARENT YELLOW OXIDE Y42 10.48 1.26 35.0 24.0 41.0 9.0 29.9 61.1 4.68 578
HP 33139 ORGANIC YELLOW (RS) Y83 8.62 1.03 20.0 21.7 58.3 11.3 22.3 66.4 5.10 612
HP 33151 LIGHT ORGANIC YELLOW Y151 8.74 1.05 26.0 20.3 53.7 17.5 20.8 61.7 4.58 561
HP 33184 BISMUTH VANADATE Y184 15.31 1.838 55.6 19.5 24.9 16.5 31.8 51.7 3.86 462
HP 3342 LT. LEMON YELLOW OXIDE Y42 13.84 1.66 55.0 20.0 25.0 22.8 31.2 46.0 3.43 412
HP 3434 DIARYLIDE ORANGE OR34 8.70 1.05 22.0 30.0 48.0 16.4 27.3 56.3 4.20 501
HP 3550 TRANSPARENT RED OXIDE R101 10.48 1.26 35.0 24.0 41.0 9.0 29.9 61.1 4.68 578
HP 35101 RED OXIDE LIGHT R101 14.93 1.79 56.0 20.6 23.4 19.5 34.3 46.2 3.50 420
HP 35103 RED OXIDE DARK R101 15.90 1.91 60.0 22.0 18.0 22.2 39.2 38.6 2.86 343
HP 35172 LIGHT ORGANIC RED R170 8.56 1.03 22.0 31.6 46.4 16.0 30.3 53.7 3.99 478
HP 35175 DEEP ORGANIC RED R170 8.29 0.96 20.0 22.3 57.7 14.7 20.7 64.6 4.79 575
HP 3519 QUINACRIDONE RED V19 8.42 1.01 19.0 19.6 61.4 13.3 16.9 69.8 5.17 621
HP 35522 BON MAROON R52.2 8.63 1.04 23.0 26.2 50.8 17.0 25.3 57.7 4.37 524
HP 3636 PHTHALO GREEN (YS) GR36 9.53 1.14 24.0 27.5 48.5 9.3 29.2 61.5 4.63 551
HP 367 PHTHALO GREEN GR7 9.10 1.09 23.0 26.4 50.6 12.4 26.8 60.8 4.60 551
HP 3700B RAW UMBER BR7 12.64 1.52 50.3 23.3 26.4 22.7 25.7 51.6 3.33 400
HP 3711 BURNT UMBER BR7 13.02 1.56 51.0 24.6 24.4 21.9 35.5 42.6 3.15 377
PIGMENT DISPERSIONS: HPHIGH-PERFORMANCE ACRYLIC DISPERSIONS FOR SOLVENTBORNE SYSTEMS (1/2)
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
% by Weight % by Volume VOC
Code Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/L
HP 3722 VAN DYKE BROWN N/A 11.38 1.36 42.0 17.7 40.3 15.7 22.5 61.8 4.59 551
HP 3800 PHTHALO BLUE NFNC B15.2 8.67 1.04 22.0 24.2 53.8 14.9 22.2 62.9 4.66 559
HP 38152 PHTHALO BLUE (RS) B15.2 8.58 1.03 21.0 24.4 54.6 14.2 22.5 63.3 4.68 561
HP 38154 PHTHALO BLUE (GS) B15.4 8.89 1.07 22.0 33.0 45.0 14.5 33.1 52.4 3.99 478
HP 3819 QUINACRIDONE VIOLET V19 8.26 0.99 12.0 26.2 61.8 8.0 22.1 69.9 5.10 612
HP 3823 CARBAZOLE VIOLET V23 8.16 0.98 10.0 22.0 68.0 6.6 18.2 75.2 5.60 666
HP 3900M HIGH JET. MASSTONE BLACK BK7 8.64 1.04 18.0 35.0 47.0 10.0 21.0 69.0 3.90 467
HP 3921M HI STRENGTH TINTING BLACK BK7 9.19 1.10 21.0 30.0 49.0 12.0 30.0 58.0 3.90 467
HP 3955M MASSTONE BLACK BLK7 8.89 1.07 22.0 33.0 45.0 13.0 32.1 54.9 4.00 480
HP 397T TINTING BLACK BK7 9.60 1.15 28.0 30.0 42.0 17.8 27.4 54.8 4.02 481
PIGMENT DISPERSIONS: HPHIGH-PERFORMANCE ACRYLIC DISPERSIONS FOR SOLVENTBORNE SYSTEMS (2/2)
SERIES 2000 XVOC DISPERSIONS are liquid pigment dispersion concentrates for tinting and masstone applications. They are very low VOC and compatible with most solventborne systems. All pigments used in XVOC Dispersions exhibit lightfastness, heat resistance and bleed resistance properties.
Vehicle: Modified Aldehyde Solvent: Oxsol 100
Technical Data:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
% by Weight % by Volume VOCCode Description Color Index Wt/Gal,Lbs Specific Gravity Pigment Vehicle Solids Volatiles Pigment Vehicle Solids Volatiles Lbs/Gal G/LXVOC 0106 TITANIUM WHITE (TW) WH6 16.73 2.01 55.6 17.9 26.5 27.9 32.5 39.6 0.031 3.68XVOC 0300 TRANSPARENT YELLOW OXIDE Y42 13.05 1.57 29.4 18.4 52.2 12.9 26.2 60.9 0.035 4.24XVOC 0315183 L/F MEDIUM YELLOW (MY) Y83 10.96 1.32 36.0 28.0 36.0 30.6 34.1 35.3 0.022 2.64XVOC 03175 ORGANIC YELLOW G/S (OY) Y151 10.93 1.31 30.6 24.0 45.4 26.4 29.2 44.4 0.026 3.08XVOC 0342 YELLOW IRON OXIDE (YO) Y42 16.71 2.01 53.8 13.69 32.5 26.3 25.8 47.9 0.039 4.66XVOC 043436 L/F ORANGE (UO) OR34 10.90 1.31 26.3 22.3 51.4 23.0 26.9 50.1 0.029 3.44XVOC 0500 TRANSPARENT RED OXIDE R101 12.78 1.53 22.5 13.5 64.0 8.0 18.9 73.1 0.051 6.14XVOC 05102 RED OXIDE (RO) R101 17.63 2.12 59.5 12.7 27.8 15.2 25.8 59.0 0.041 4.88XVOC 05173 MONO AZO RED R173 10.88 1.31 30.0 20.6 49.4 27.2 24.8 48.0 0.026 3.07XVOC 0519 QUINACRIDONE RED (QR) V19 10.66 1.28 17.7 28.3 54.0 15.4 33.1 51.5 0.031 3.76XVOC 05522 BON MAROON R52.2 10.63 1.28 12.4 34.2 53.4 9.5 39.8 50.7 0.027 3.22XVOC 067 PHTHALO GREEN (PG) GR7 11.10 1.33 20.0 36.0 44.0 12.5 43.8 43.7 0.025 2.94XVOC 0700 RAW UMBER (RU) BR7 13.46 1.62 38.5 22.1 39.4 19.1 33.5 47.4 0.027 3.23XVOC 0711 BURNT UMBER (BU) BR7 14.34 1.72 46.3 23.3 30.4 24.0 36.7 39.3 0.115 13.74XVOC 0815254 PHTHALO BLUE (PB) B15.2 10.85 1.30 24.8 29.7 45.5 20.0 38.8 41.2 0.026 3.14XVOC 0819 QUINACRIDONE VIOLET (QV) V19 10.67 1.28 20.1 29.9 50.0 17.3 35 47.7 0.025 3.01XVOC 0900 JET BLACK BK7 10.69 1.28 9.5 31.1 59.4 6.8 36.5 56.7 0.032 3.80XVOC 097 LAMP BLACK (LB) BK7 11.02 1.32 17.8 28.1 54.1 13.1 33.7 53.2 0.029 3.44
PIGMENT DISPERSIONS: XVOC HIGH-PERFORMANCE LOW VOC DISPERSIONS FOR SOLVENTBORNE SYSTEMS
TONERS FOR WHITE PRODUCTS are special blends of pigments that produce a specific hue which masks the initial yellowness of whites, the aged yellowness created by using amber resins or over processing.
Toned whites have a more pleasing appearance due to the warm blue-white tone yielded. Toners also increase the opacity of whites without drastically affecting the reflectance value.
Applications:
• Used to make white systems appear whiter• Overcome the problem of yellow tones associated with whites• Increase the hiding power (opacity) of whites• Mask the aged look of whites as they yellow
Color Strength and Hue Control Specifications: Toners are quality controlled to ± 2% of tinting strength and maximum total color hue tolerance of One ∆ E.
Available Toners:
• AD EX 319D: Toner for solventborne systems• WB EX 258D: Toner for waterborne systems
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
PIGMENT DISPERSIONS: TONERSFOR WHITE PRODUCTS
Dispersants Description Aqueous Solvent % Use Based OnSUPERSPERSE® 95 Multifunctional dispersant YES 2.0 - 5.0 PSUPERSPERSE® 100 Highly effective dispersant for water-reducible and emulsion systems YES 2.0 - 15.0 PSUPERSPERSE® 200 Highly effective dispersant for water-reducible and emulsion systems YES 1.0 - 3.0 PSUPERSPERSE® E-ONE APE and NPE-free wetting/dispersing agent for aqueous systems YES 4.0-12.0 PSUPERSPERSE® E-TWO APE and NPE-free wetting/dispersing agent for aqueous systems YES 4.0-12.0 PSUPERSPERSE® E-THREE APE and NPE-free wetting/dispersing agent for aqueous systems YES 4.0-12.0 PSUPERSPSERSE® 1000 Versatile dispersant for solventborne systems YES 5.0 - 10.0 PSUPERSPERSE® 3000 Universal dispersing vehicle YES YES 1.0 - 10.0 PSUPERSPERSE® AD Versatile dispersant and additive for solventborne systems YES 5.0 - 10.0 PSUPERSPERSE® DRY Powder wetting and dispersing agent for aqueous systems YES 3.0 - 5.0 PSUPERSPERSE® EM-40 Zero VOC, APE and NPE-free dispersing agent YES 2.0 - 15.0 PFixersFX 1 Surface control agent for conventional aqueous systems YES 0.2 - 1.0 TWFX 2 Surface control agent for high solids aqueous systems YES 0.1 - 0.8 TWFX 3 Surface control agent for Aqueous 2 component epoxies and alkyds YES YES 0.2 - 1.0 TWFX 4 Stabilizing and anti-gelling agent YES 0.5 - 1.0 TWDefoamersFB 100 Silicone modified hydrocarbon defoamer for solventborne systems YES 0.5 - 1.0 TWFB 200 Silicone-free polymeric defoamer YES 0.2 - 1.0 TWFB 500 Silicone-free defoamer for water-reducibles YES 0.05 - 1.0 TWFB S-40 Zero VOC concentrated, modified organo-silicone defoamer YES 0.5 - 1.0 TWDriersSUPERDRY 1000 Cobalt drier replacement for alkyds, oils and polyurethanes that prevents yellowing YES 0.5 - 0.7 VSSUPERDRY WB99 Cobalt drier replacement that prevents yellowing and improves colors YES 0.5 - 0.7 VSFlatting PastesEZ FLAT AQ Flatting paste for aqueous systems YESEZ FLAT 20BA Flatting paste for systems which Butyl Acetate is the preferred solvent YES EZ FLAT A-100 Flatting paste for systems which Aromatic 100 is the preferred solvent YESEZ FLAT W-30 Flatting paste for systems containing resinsEZ FLAT 20 MS Flatting paste for systems containing Aliphatic and Aromatic solvents YES VS
LEGEND: P = Based on Pigment VS = Based on Vehicle Solids TW = Based on Total Formula Weight
SPECIALTY ADDITIVESPRODUCT GUIDE (1/2)
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
Waxes Description Aqueous Solvent % Use Based OnSUPERSLIP 35 Carnauba wax for low coefficient of friction, and excellent mar and scuff resistance YES 0.5 - 2.5 TWSUPERSLIP 41 Polyethylene for excellent block and abrasion resistance YES 1.0 - 4.0 TWSUPERSLIP 45 Paraffin for H20 beading and excellent block resistance in ambient cure systems YES 3.0 - 5.0 TWSUPERSLIP EX Polyethylene for excellent block and abrasion resistance YES 0.25 - 1.25 TWThickenersEZ GEL 15A100 Rheological additive containing Aromatic 100 for anti-settling and sag control YES 0.5 - 5.0 TWEZ GEL 15nBA Rheological additive containing n-Butyl Acetate for anti-settling and sag control YES 0.5 - 5.0 TWEZ GEL 15X Rheological additive containing Xylene for anti-settling and sag control YES 0.5 - 5.0 TWEZ GEL MS Rheological additive containing Mineral spirits for anti-settling and sag controlEZ GEL NOVOC TBA Rheological additive containing Tertiary Butyl Acetate (VOC Exempt) for anti-settling and sag control YES 0.5 - 5.0 TWEZ GEL W16 Aqueous rheological additive for anti-settling and sag control YES 0.5 - 5.0 TW
LEGEND: P = Based on Pigment VS = Based on Vehicle Solids TW = Based on Total Formula Weight
SPECIALTY ADDITIVESPRODUCT GUIDE (2/2)
SUPERSPERSE® 95 is a multifunctional dispersant that is used in both the grind and the letdown phase.
It eliminates the need for additional buffers such as ammonia, TEA or Aminomethyl Propanol in a coating system. SUPERSPERSE 95® is UV stable and, under most conditions, will not cause discoloration.
Application: In latex systems, SUPERSPERSE® 95 is used in conjunction with other common dispersants. In the grind, reduce the level of current dispersant by 30 to 40% and replace with SUPERSPERSE® 95 at 0.75 to 1.00 pound per 100 gallons.
Better pigment dispersion and shorter dwell times will be realized, which can reduce the amount of prime pigments needed to achieve desired opacity and/or tint strength. In most cases, a 10% reduction of glycols will be possible.
Recommended Usage Level: Adjust the final pH with SUPERSPERSE® 95 at 0.5 to 1.0 pound per 100 gallons.
• SUPERSPERSE 95® helps establish a stable pH which reduces flash rusting and improves thickener performance without negatively affecting the early water sensitivity of the system.
• Stable pH properties will reduce the occurrence of pigment flocculation for products that require extended shelf-life.
• Additional benefits include better scrub and water resistance due to the lower content of conventional non-volatile dispersants.
• SUPERSPERSE 95® has very low odor and is not detected by most observers when properly applied.
Typical Properties:
% Active Weight 100%
Weight per Gallon (lbs) 7.83 ± 0.2
pH 11.0 - 14.0
Viscosity (CPS) 10.0 - 15.0
SUPERSPERSE®
95MULTIFUNCTIONAL DISPERSANT (1/2)
All samples < 1.00 delta E after 500 hours vs. unexposed controlsAll samples < 0.20 delta E comparing exposed control vs. 0.5% by weight addition of SUPERSPERSE 95®
�
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
95MULTIFUNCTIONAL DISPERSANT (2/2)
SUPERSPERSE® 100 is a versatile wetting, dispersing and stabilizing agents for water-reducible and emulsion systems.
It can be used as a grinding vehicle or additive, and will not interfere with gloss, film integrity or water resistance of finished coatings. It is also compatible with latex emulsions, epoxies, water-reducible alkyds, polyesters and acrylics.
Note: To avoid the possibility of shock, vehicle systems should have a pH of 6-10.
Application: SUPERSPERSE® 100 is effective with organic or inorganic pigments. For optimum results, use the appropriate dispersing agent for specific pigments.
• Titanium Dioxide• Organic Yellows• Organic Reds• Organic Oranges• Carbon Blacks• Extender Pigments
Recommended Usage Level: Use 1% - 3% based upon weight of the pigment for inorganic pigments. Use 2% - 15% based upon weight of the pigment for organic and transparent pigments. Levels will vary depending on wetting properties of the dispersion vehicle and specific pigment(s) being milled. Optimum levels should be determined through laboratory testing.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 35.0
Gardner Color 7 Max
Weight per Gallon (lbs) 8.8
Specific Gravity 1.06
Viscosity (Gardner-Holdt) R-V
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
100WATER-REDUCIBLE AND EMULSION SYSTEMS
SUPERSPERSE® 200 is a versatile wetting, dispersing and stabilizing agents for water-reducible and emulsion systems.
It can be used as a grinding vehicle or additive, and will not interfere with gloss, film integrity or water resistance of finished coatings. It is also compatible with latex emulsions, epoxies, water-reducible alkyds, polyesters and acrylics.
Note: To avoid the possibility of shock, vehicle systems should have a pH of 6-10.
Application: SUPERSPERSE® 200 is effective with organic or inorganic pigments. For optimum results, use the appropriate dispersing agent for specific pigments.
• Natural Iron Oxides • Synthetic Iron Oxides• Napthols and Quinacridones• Phthalo Blues • Phthalo Greens• Lead Pigments
Recommended Usage Level: Use 1% - 3% based upon weight of the pigment for inorganic pigments. Use 2% - 15% based upon weight of the pigment for organic and transparent pigments. Levels will vary depending on wetting properties of the dispersion vehicle and specific pigment(s) being milled. Optimum levels should be determined through laboratory testing.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 46.0
Gardner Color 9 Max
Weight per Gallon (lbs) 8.7
Specific Gravity 1.04
Viscosity (Gardner-Holdt) G-K
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
200WATER-REDUCIBLE AND EMULSION SYSTEMS
SUPERSPERSE® E-ONE is an APE and NPE-free versatile wetting, dispersing and stabilizing agent for all water-reducible and emulsion systems.
It can be used as the sole dispersant or as an additive to improve resin-based dispersions. It will improve gloss, maximize color development, provide viscosity stability and will not diminish the integrity or water resistance of the final coating or ink system. It is also compatible with latex emulsions, epoxies, water-reducible alkyds, polyurethanes, polyesters and acrylics.
Note: To avoid the possibility of shock, vehicle systems should have a pH above 6.
Application: SUPERSPERSE® E-ONE is effective with a wide range of organic and inorganic pigments. This dispersant may also be used in combination when co-grinding pigments are required. For initial evaluations, we recommend using the following list as a guide.
• Titanium Dioxide • Carbon Blacks • Organic Yellows • Organic Reds • Organic Oranges • Extender Pigments
Recommended Usage Level: Use 3% - 6% based upon weight of the pigment for inorganic pigments. Use 5% - 15% based upon weight of the pigment for organic and transparent pigments. Levels will vary depending on wetting properties of the dispersion vehicle and surface treatment and shape of the specific pigment(s) being milled. Optimum levels should be determined through laboratory testing.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 40.0
Gardner Color 7 Max
Weight per Gallon (lbs) 8.56
Specific Gravity 1.03
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
E-ONEWATER-REDUCIBLE AND EMULSION SYSTEMS
SUPERSPERSE® E-TWO is an APE and NPE-free versatile wetting, dispersing and stabilizing agent for all water-reducible and emulsion systems.
It can be used as the sole dispersant or as an additive to improve resin-based dispersions. It will improve gloss, maximize color development, provide viscosity stability and will not diminish the integrity or water resistance of the final coating or ink system. It is also compatible with latex emulsions, epoxies, water reducible alkyds, polyurethanes, polyesters and acrylics.
Note: To avoid the possibility of shock, vehicle systems should have a pH above 6.
Application: SUPERSPERSE® E-TWO is effective with a wide range of organic and inorganic pigments. This dispersant may also be used in combination when co-grinding pigments are required. For initial evaluations, we recommend using the following list as a guide.
• Natural Brown Oxides • Synthetic Iron Oxides• Napthols and Quinacridones• Phthalo Blues • Phthalo Greens• Lead Pigments
Recommended Usage Level: Use 3% - 6% based upon weight of the pigment for inorganic pigments. Use 5% - 15% based upon weight of the pigment for organic and transparent pigments. Levels will vary depending on wetting properties of the dispersion vehicle and surface treatment and shape of the specific pigment(s) being milled. Optimum levels should be determined through laboratory testing.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 56.0
Gardner Color 9 Max
Weight per Gallon (lbs) 8.50
Specific Gravity 1.02
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
E-TWOWATER-REDUCIBLE AND EMULSION SYSTEMS
SUPERSPERSE® E-THREE is an environmentally friendly pigment wetting, dispersing and stabilizing agent for all types of pigments in most aqueous systems.
Application:
• Low VOC systems• Alkylphenol Ethoxylate free• Used as a single dispersing additive for multiple pigment dispersing requirements• Does not promote foam, therefore the need for defoamers in the grind phase is
minimized• Can be used as the sole dispersant or as an additive to improve resin-based
dispersions • Effective with all types of pigments• Maximizes color development, improves wetting, provides viscosity stability and
increases color acceptance • Will not diminish the integrity or water resistance of the final coating or ink
system
Recommended Usage Level: When used as the sole wetting and dispersing agent add 5 - 10% based on the weight of the pigment. When used to improve resin-based dispersions add 2-3 % based on the weight of the pigment. Add to water, co-solvent or vehicle prior to the addition of pigment. Optimum levels should be determined through laboratory testing.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 44.0
Gardner Color 10 Max
Weight per Gallon (lbs) 8.50
Specific Gravity 1.02
pH (10% Aqueous Solution) 10.0
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
E-THREEAQUEOUS SYSTEMS
SUPERSPERSE® 1000 is a versatile wetting, dispersing, and stabilizing agent for solventborne systems.
Higher pigment loadings, faster dispersion times, higher initial gloss, improved color development and gloss retention can be achieved utilizing SUPERSPERSE® 1000.
Application: SUPERSPERSE® 1000 is a modified alkyd and is compatible with the following vehicles:
• Short Oil Alkyds• Medium Oil Alkyds• Long Oil Alkyds• Oil and Alkyd Modified Urethanes• Chlorinated Rubber• Nitrocellulose• Acrylics• Raw and Bodied Oils
Recommended Usage Level: SUPERSPERSE® 1000 is effective at all usage levels. As an additive, best results are obtained by replacing 5% to 10% of vehicle solids with SUPERSPERSE® 1000.
Optimum Results: Achieved by utilizing SUPERSPERSE® 1000 as the sole dispersing vehicle.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids (by Weight) 75%
Weight per Gallon (lbs) 8.1
Specific Gravity 0.97
Gardner Color 12 Max
Viscosity (Gardner-Holdt) Q-U
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
1000SOLVENTBORNE SYSTEMS
SUPERSPERSE® 3000 can be used as a vehicle for manufacturing in-plant and machine colorants.
Dispersions based upon SUPERSPERSE® 3000 can be used in trade sales and industrial coating at levels up to 10% without affecting gloss, dry time, scrubability or chemical resistance.
Application: These “universal” dispersions are compatible with the following paint systems:
• Vinyl Toluene Oils and Alkyds• Oil and Alkyd Modifiers• Styrenated Alkyds• Two-Component Epoxies• Chlorinated Rubber• Nitrocellulose• Epoxy Ester• Short Oil Alkyds
Recommended Usage Level: Dilute 10:6 with a suitable organic solvent. The maximum pigment concentration attainable in the diluted SUPERSPERSE® 3000 is approximately 20% for organic pigments and 70% for inorganic pigments. Additionally, SUPERSPERSE® 3000 can be used as an additive to improve compatibility in most systems. The addition of 1% - 3% based upon total weight can significantly improve color acceptance and reduce flooding and floating.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Solids 75%
Weight per Gallon (lbs) 8.0
Specific Gravity 0.96
Viscosity (Gardner-Holdt) S-V
Gardner Color 10 Max
Solvent Oderless Mineral Spirits
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
3000GRINDING VEHICLE/COLOR ACCEPTANCE ADDITIVE
SUPERSPERSE® AD is a specifically formulated pigment grinding vehicle which produces colorants with a broad range of compatibility.
The excellent wetting characteristics of this product allow pigment concentrates to be manufactured with low viscosity and stable high pigment loads.
Application: Pigment dispersions based upon SUPERSPERSE® AD are being successfully used in the following systems:
• Oil Modified Urethanes• Short Oil Alkyds• Medium Oil Alkyds• Long Oil Alkyds• Alkyd Copolymers• Chain Stopped Alkyds• Nitrocellulose
Optimum Results: Can be diluted with aliphatics, aromatics, esters and ketones.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Vehicle Modified Alkyd
Solvent Mineral Spirits
% Active Solids 70.0
Weight per Gallon (lbs) 7.94
Flash Point F/C 104/40
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
ADGRINDING VEHICLE FOR SOLVENTBORNE SYSTEMS
SUPERSPERSE® DRY is a desiccated multifunctional dispersant and wetting agent in powder form. It is easily dissolved in water and used for both liquid and dry applications.
Application: It can be used in dry blend formulations which require mixing with water prior to application. SUPERSPERSE® DRY will improve the wetting of the solid dry particles in the blend such as pigment, sand, cement, fibers as well as special effect chips and specks.
Due to SUPERSPERSE® DRYs accelerated wetting properties of pigments and fillers, additional benefits include more uniform color strength development, system stability and resistance to color float.
SUPERSPERSE® DRY is widely used in traditional wet paint, ink and caulk systems. It is also used in the manufacture of pigment dispersions as it is an effective pigment wetting and dispersion additive for both inorganic and organic pigments. It can also be used in the following:
• Mortars• Joint Fillers• Plasters• Leveling Compounds• Pigment-Powder Blends
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Color Amber
Form Powder
% Active by Weight 95%
Weight per Gallon (lbs) 5.4
Nature Anionic
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
DRYDRY POWDER PIGMENT DISPERSANT/WETTING AGENT
SUPERSPERSE® EM-40 is a ZERO VOC as well as an APE and NPE-free product. It can be used as a vehicle for manufacturing in-plant and universal machine colorants.
Dispersions based upon SUPERSPERSE® EM-40 can be used in trade sales and industrial coatings at levels up to 10% without affecting gloss, dry time, scrubability or chemical resistance. These “universal” dispersions are compatible with the following paint systems:
Application: SUPERSPERSE® EM-40 is commonly used as an additive to improve compatibility and color acceptance in solvent, aqueous and 100% solids systems. SUPERSPERSE® EM-40 can be incorporated into the dispersion/colorant or the base system. An addition of 0.5% - 3% based upon total weight of the base system or dispersion can significantly improve color acceptance and eliminate or minimize flooding and floating.
Recommended Usage Level: When used as a grinding vehicle, SUPERSPERSE® EM-40 can be diluted 1:1 with a suitable organic solvent. The average pigment concentration attainable in the diluted SUPERSPERSE® EM-40 is approximately 20% for organic pigments and 70% for inorganic pigments. SUPERSPERSE® EM-40 will also assist in keeping the colorant from drying too rapidly.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Solids 35.0
Gardner Color 7 Max
Weight per Gallon (lbs) 8.8
Specific Gravity 1.06
Viscosity (Gardner-Holdt) R-V
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SUPERSPERSE®
EM-40MULTIFUNCTIONAL DISPERSANT
• Alkyds and Monomer Modified Alkyds
• Oil and Alkyd Modified• Polyurethanes• Styrenated Alkyds• 2K Epoxies and Epoxy Ester
• Chlorinated Rubber• Water Reducible Alkyds,
Polyesters and Acrylics• Acrylic Emulsions• PVA Emulsions• PUD
FX 1 is used to reduce or eliminate film defects such as craters, crawling and fish eyes. It also provides uniform films on difficult to wet or contaminated substrates.
Fixers are specifically formulated to be highly effective at low levels without adversely effecting inter-coat adhesion.
Application: FX 1 is an extremely effective surface control agent for conventional aqueous systems.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Solids 50%
Weight Per Gallon (lbs) 8.59
Viscosity (Gardner-Holdt) A3
FDA Cleared Yes
Suggested Use Level 0.2%-1.0%
VoC lbs per Gallon (GR/L) 2.78/333
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FIXERS: FX 1AQUEOUS SYSTEMS
FX 2 is used to reduce or eliminate film defects such as craters, crawling and fish eyes. It also provides uniform films on difficult to wet or contaminated substrates.
Fixers are specifically formulated to be highly effective at low levels without adversely effecting inter-coat adhesion.
Application: FX 2 is an extremely effective surface control agent for high solids aqueous systems.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Solids 78%
Weight Per Gallon (lbs) 9.00
Viscosity (Gardner-Holdt) C-G
FDA Cleared Yes
Suggested Use Level 0.1%-0.8%
VoC lbs per Gallon (GR/L) 0.59/70
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FIXERS: FX 2AQUEOUS SYSTEMS
FX 3 is used to reduce or eliminate film defects such as craters, crawling and fish eyes. It also provides uniform films on difficult to wet or contaminated substrates.
Fixers are specifically formulated to be highly effective at low levels without adversely effecting inter-coat adhesion.
Application Waterborne Systems: FX 3 is extremely effective surface control agent for Aqueous 2K Systems.
Application Solventborne Systems: FX 3 extremely effective surface control agent for epoxy and alkyd systems
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Solids 50%
Weight Per Gallon (lbs) 8.44
Viscosity (Gardner-Holdt) A3
FDA Cleared Yes
Suggested Use Level 0.2%-1.0%
VoC lbs per Gallon (GR/L) 3.30/395
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FIXERS: FX 3AQUEOUS AND SOLVENTBORNE SYSTEMS
FX 4 is a viscosity stabilizer and anti-gelling agent, plus pigment wetting and dispersing additive.
Application: FX 4 helps prevent viscosity increase during manufacture and storage. It will also help stabilize and cure problem pigment/vehicle systems that have a tendency to gel over time. Increased viscosity and/or gelling due to premature vehicle polymerization, gradual changes in a vehicles absorption on pigments or pigments having a drier or catalyst that contain high metal content such as umbers and magnetic iron oxides can be reduced or eliminated using FX 4. FX 4 is an effective wetting and dispersing additive for dispersions that are difficult to grind. FX 4 can be used with pigments such as: carbon blacks, magnetic iron oxides, nano sized particles and other high surface area inorganic and organic pigments.
Recommended Usage Level: Use 1% - 2% based upon mill base weight to improve pigment wetting and dispersion. Use 0.5% - 1.0% based upon total formula weight to prevent vehicle polymerization and self-cross linking of the vehicle during storage.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active Ingredients 100%
Appearance Dark Amber Liquid
Weight per Gallon (lbs) 7.58
Specific Gravity 0.91
Flash Point F/C 230/110
Viscosity (Gardner-Holdt) Z2-Z4
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FIXERS: FX 4SOLVENTBORNE SYSTEMS
FB 100 is a silicone modified hydrocarbon blend that provides rapid defoaming in solvent systems without causing film defects such as craters, crawling and fish eyes.
FB 100 improves flow and leveling, and can often reduce or eliminate cratering and crawling on hard to wet substrates.
Note: In moisture cured systems, FB 100 should be added immediately before application to avoid reaction in the container.
Application:• Oil and Alkyd Modified Urethanes• Alkyd wood stains• Nitrocellulose Lacquers• Epoxies• Chlorinated Rubber• Moisture-cured Urethanes
Recommended Usage Level: Use 0.5% - 1.0% based upon total formula weight. FB 100 can be added at any time during the manufacturing process or in the finished coating prior to application.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Weight per Gallon (lbs) 7.07
Specific Gravity 0.85
Flash Pont F/C 104/37
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DEFOAMERS: FB 100 SOLVENTBORNE SYSTEMS
FB 200 is a silicone free Polymeric organic defoamer.
Recommended Usage Level: Use 0.2% – 1.0% of total formula
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Translucent Liquid
Viscosity (CPS) 100-500
Weight per Gallon (lbs) 7.60 ± 0.2
Specific Gravity 0.9124 ± 0.025
pH 7.0-10.0
NV by Weight 98.0 ± 2.0%
NV by Volume 98.0 ± 2.0%
Water by Weight 2.0 98.0 ± 2.0%
Water by Volume 2.0 98.0 ± 2.0%
VoC by Weight None
VoC by Volume None
Shelf Life 1 Year
Storage Precaution Store at room temperature above 40°F
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DEFOAMERS: FB 200 AQUEOUS SYSTEMS
FB 500 is a silicone-free defoamer designed specifically for chronic foam problems associated with dip and flow coatings applications in water reducible, alkyd and polyester systems.
It is effective in both high and low viscosity coatings. FB 500 is not only effective at destabilizing surface foam, it also eliminates micro foam within the coating. FB 500 will not affect intercoat adhesion and may be added at any stage of production, provided it is added while under agitation.
Recommended Usage Level: Use 0.5% – 1.0% based on total formula weight
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Translucent Liquid
Viscosity (#2 Zahn) 20 ± 5 seconds
Weight per Gallon (lbs) 6.75 ± 0.2
Specific Gravity 0.8103 ± 0.025
pH (10% Dispersion in Water) 7.0-10.0
NV by Weight 100.0 ± 0.5%
NV by Volume 100.0 ± 0.5%
Shelf Life 1 Year
Storage Precaution Store at room temperature above 40°F
Packaging 390 lbs Drum
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DEFOAMERS: FB 500 AQUEOUS SYSTEMS
FB S-40 is a highly effective, concentrated, modified organo-silicone antifoam. It has excellent water dilution stability and is extremely effective on surfactant-based foams.
Recommended Usage Level: Use 0.05% - 1.0% based upon total formula weight.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Translucent Liquid
Viscosity (CPS) 2500 - 4500
Weight per Gallon (lbs) 8.21 ± 0.2
Specific Gravity 0.985 ± 0.024
NV by Weight 65.0 ± 2.0 %
NV by Volume N/A
VoC by Volume N/A
Packaging 41 lbs Pails
Shelf Life 1 Year
Storage Precaution Store at room temperature above 40°F
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DEFOAMERS: FB S-40 AQUEOUS SYSTEMS
SUPER DRY 1000 is a specially formulated drier to replace cobalt drier in systems where cobalt can cause adverse side effects. It is highly effective in oil or alkyd modified polyurethanes, as well as in conventional alkyds.
Advantages:
• Reduces discoloration of polyurethane in the can• Improves alkali resistance of polyurethane films• Prevents loss of dry• Greatly reduces yellowing of air dry alkyd finishes
Recommended Usage Level: The following starting point recommendation is based upon 100 pounds of vehicle solids.
Optimum Results: Are obtained by combining Super Dry 1000 with zirconium and calcium
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
SUPER DRY 1000 0.5 Lbs.-0.7 Lbs.Zirconium (as metal) 0.1 Lbs.-0.3 Lbs.Calcium (as metal) 0.05 Lbs.-0.10 Lbs.
Weight per Gallon (lbs) 7.1
Specific Gravity 0.85
Solvent Blend of Xylene and n-Butanol
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DRIERS: SUPER DRY 1000MODIFIED POLYURETHANES AND ALKYDS
SUPER DRY WB is a water dispersible version of SUPER DRY 1000. This product is specially formulated to replace cobalt drier where cobalt can cause adverse side effects.
Advantages:
• Improved color appearance of bright whites, clears and light colors• Prevents loss of dry• Greatly reduces yellowing
Recommended Usage Level: Can be used as a single drier.
Optimum Results: Obtained by combining SUPER DRY WB99 with zirconium and calcium. The following starting point recommendation is based upon 100 pounds of vehicle solids:
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
SUPER DRY WB99 0.5 Lbs.-0.7 Lbs.
Zirconium (as metal) 0.1 Lbs.-0.3 Lbs.
Calcium (as metal) 0.05 Lbs.-0.10 Lbs.
Weight per Gallon (lbs) 7.9
Specific Gravity 0.95
Solvent Dipropylene Glycol Monomethyl Ether (DPM)
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
DRIERS: SUPER DRY WB99WATER-REDUCIBLE SYSTEMS
EZ FLAT AQ is a matting/flatting paste for gloss reduction in aqueous systems.
Application: EZ FLAT AQ is an easy to use stir-in dispersion which provides consistent gloss reduction. It is also used for making final gloss adjustments which ensures your product is within specification and right on standard. EZ FLAT AQ allows users to avoid the unwanted dust associated with processing dry silica during the manufacturing or compounding process. EZ FLAT AQ contains amorphous silica for flatting and a polyolefin blend for scratch, scuff and polish resistance. The polyolefin blend also provides additional anti-blocking properties when using the EZ FLAT AQ in topcoats.
Suggested Incorporating Technique: EZ FLAT AQ should always be mixed prior to use. In most cases it will be more viscous then the systems in which it will be used. Because of this, we recommend pre-mixing it by diluting it with 5-10% water, then added slowly into the batch while it is under agitation.
Typical Use Level: Ranges from 5.0 - 15.0%. Use levels are dependent upon the type of resin for the EZ FLAT AQ incorporation. Other factors include film thickness and dry time.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Silica and Polyolefin 31.0
% Vehicle (Surfactant) 1.0
% Propylene Glycol/ % Water 11.0/57.0
Weight per Gallon (lbs) 9.61
Specific Gravity 1.15
VoC lbs per Gallon 3.19
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FLATTING PASTES: EZ FLAT AQ AQUEOUS SYSTEMS
EZ FLAT 20 BA is a matting/flatting paste for systems in which Butyl Acetate is the preferred solvent such as lacquers and bake finishes.
Suggested Incorporating Technique: EZ FLAT 20 BA should always be mixed prior to use. In most cases the EZ FLAT 20 BA will be more viscous than the systems in which it will be used. Because of this we recommend pre-mixing EZ FLAT 20 BA first by diluting it with 5-10% solvent to be comparable with the viscosity of the system for incorporation, then added slowly into the batch while it is under agitation.
Typical Use Level: Add 5% by weight, to reduce gloss 70% at 60°. System solids and force cure vs. ambient will effect actual level required. For consistent results, agitate lightly before using (based on 35% vehicle solids).
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Silica 15.0
% Vehicle 0.0
% Solvent 85.0 n Butyl Acetate
Weight per Gallon (lbs) 8.04
Specific Gravity 0.96
Flash Point F/C (closed cup) 83°/28°
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FLATTING PASTES: EZ FLAT 20 BA SOLVENTBORNE SYSTEMS
EZ FLAT A-100 is a matting/flatting paste for systems which Aromatic 100 is the preferred solvent such as lacquers and bake finishes.
Suggested Incorporating Technique: EZ FLAT should always be mixed prior to use. In most cases, the EZ FLAT will be more viscous than the systems in which it will be used. Because of this, we recommend pre-mixing EZ FLAT first by diluting it with 5-10% solvent to be comparable with the viscosity of the system for incorporation, then added slowly into the batch while it is under agitation.
Typical Use Level: Add 5% by weight, to reduce gloss 70% at 60°. System solids and force cure vs. ambient will effect actual level required. For consistent results, agitate lightly before using (based on 35% vehicle solids).
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Silica 15.0
% Vehicle 0.0
% Solvent 85.0 Aromatic 100
Weight per Gallon (lbs) 7.84
Specific Gravity 0.94
Flash Point F/C (closed cup) 110°/43°
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FLATTING PASTES: EZ FLAT A-100 SOLVENTBORNE SYSTEMS
EZ FLAT W-30 is an easy to use stir-in dispersion which provides consistent gloss reduction. It is also used for making final gloss adjustments which insures your product is within specification and right on standard. EZ FLAT W-30 allows users to avoid the unwanted dust associated with processing dry silica during the manufacturing or compounding process. EZ FLAT W-30 contains amorphous silica for flatting and a polyolefin blend or scratch, scuff and polish resistance. The polyolefin blend also provides additional anti-blocking properties when using the EZ FLAT W-30 in topcoats.
Suggested Incorporating Technique: The EZ FLAT W-30 should always be mixed prior to use. In most cases, the EZ FLAT W-30 will be more viscous then the systems in which it will be used. Because of this, we recommend pre-mixing it by diluting it with 5-10% water and added slowly into the batch while it is under agitation.
Typical Use Level: Typical use levels range from 5.0 - 15.0%. Use levels are dependent upon the type of resin into which the EZ FLAT W-30 is being incorporated. Other factors include film thickness and dry time.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Silica and Polyolefin 31.0
% Vehicle (Surfactant) 1.0
% Propylene Glycol/ % Water 11.0/57.0
Weight per Gallon (lbs) 9.61
Specific Gravity 1.15
VOC per Gallon (lbs) 3.19
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FLATTING PASTES: EZ FLAT W-30 AQUEOUS SYSTEMS
EZ FLAT 20 MS is a matting/flatting paste for systems containing Aliphatic and Aromatic solvents such as alkyd and oil-modified polyurethanes.
Suggested Incorporating Technique: EZ FLAT should always be mixed prior to use. In most cases, the EZ FLAT will be more viscous than the systems in which it will be used. Because of this we recommend pre-mixing EZ FLAT first by diluting it with 5-10% solvent to be comparable with the viscosity of the system for incorporation. This pre-mix should be added slowly into the batch while it is under agitation.
Typical Use Level: Add 5% by weight, to reduce gloss 70% at 60°. System solids and force cure vs. ambient will effect actual level required. For consistent results, agitate lightly before using (based on 35% vehicle solids).
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Silica 15.0
% Vehicle 0.0
% Solvent 85.0 Mineral Spirits
Weight per Gallon (lbs) 7.50
Specific Gravity 0.90
Flash Point F/C (closed cup) 107°/42°
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
FLATTING PASTES: EZ FLAT 20 MS SOLVENTBORNE SYSTEMS
SUPERSLIP 35 is a carnauba wax with a very low coefficient of friction that exhibits excellent mar and scuff resistance.
Note: The components of this product meet the following:
• FDA STATUS 21CFR 175.105• Approved under 175.300 (extractives not to exceed 0.5 mg per square inch per
extractive limits in 175.300(c))• Approved under 175.320 (must meet extractive limits in 176.170(c))• Approved under 176.170 (must meet extractive limitations in 176.170(c) and
176.180)
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Wax Carnauba
% Solids 35.0
Volatiles Water
Average Particle Size 150nm
Specific Gravity 1.00
Viscosity (CPS) <25 #1 Spindle @60RPM
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
WAXES: SUPERSLIP 35 AQUEOUS SYSTEMS
SUPERSLIP 41 is a polyethylene with excellent block and abrasion resistance.
Note: The components of this product meet the following:
• FDA STATUS 21CFR • Approved under 175.105
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Wax Polyethylene
% Solids 35.0
Volatiles Water
Average Particle Size 35nm
Specific Gravity 1.01
Viscosity (CPS) <50 #2 Spindle @60RPM
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
WAXES: SUPERSLIP 41 AQUEOUS SYSTEMS
SUPERSLIP 45 is a paraffin wax that exhibits excellent block resistance in ambient cure systems and water beading properties.
Note: The components of this product meet the following:• FDA STATUS 21CFR 175.105• Approved under 175.320 and 176.180 (must meet extractive limits in 176.170(c))• Approved under 176.170 for food Type VII-B only if no extractive limitations
performed• Approved for other food types and conditions of use (must meet extractive
limitations in 176.170(c))
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Wax Paraffin
% Solids 35.0
Volatiles Water
Average Particle Size 180nm
Specific Gravity 8.08
Viscosity <150 CPS #3 Spindle @60RPM
Recommended Range 8.5-9.5
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
WAXES: SUPERSLIP 45 SOLVENTBORNE COATINGS
SUPERSLIP EX is a polyethylene with excellent block and abrasion resistance.
Note: The components of this product meet the following:
• FDA STATUS 21CFR 175.105• Approved under 175.320 and 176.180 (must meet extractive limits in 176.170(c))• Approved under 175.3 (extractives not to exceed 0.5 mg per square inch per
extractive limits in 175.300)• Approved under 176.170 for food Type VII-B only if no extractive limitations
performed• Approved for other food types and conditions of use (must meet extractive
limitations in 176.170(c))
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Wax Polyethylene
% Solids 25.0
Volatiles Water
Average Particle Size 45nm
Specific Gravity 1.01
Viscosity (CPS) <20 #1 Spindle @60RPM
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
WAXES: SUPERSLIP EX AQUEOUS SYSTEMS
EZ GEL MS is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 17
Weight per Gallon (lbs) 7.90
Solvent Aromatic 100
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL 15A100 SOLVENTBORNE SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of
manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment
orientation• Reduced pigment flooding and
floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
EZ GEL 15nBA is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 16
Weight per Gallon (lbs) 7.83
Solvent n Butyl Acetate
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL 15nBASOLVENTBORNE SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment orientation• Reduced pigment flooding and floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
EZ GEL 15X is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 16
Weight per Gallon (lbs) 7.82
Solvent Xylene
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL 15XSOLVENTBORNE SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of
manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment
orientation• Reduced pigment flooding and
floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
EZ GEL MS is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 16
Weight per Gallon (lbs) 7.14
Solvent Mineral Spirits
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL MS SOLVENTBORNE SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment orientation• Reduced pigment flooding and floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
EZ GEL NOVOC TBA is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 16
Weight per Gallon (lbs) 7.77
Solvent Tertiary Butyle Acetate (VOC Exempt)
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL NOVOC TBASOLVENTBORNE SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of
manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment
orientation• Reduced pigment flooding and
floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
EZ GEL W 16 is a multifunctional treated mineral that provides excellent anti-settling properties and superior sag control with minimal impact on viscosity.
Benefits:
Typical Use Level: Use 0.5% to 5.0% based on total formula weight. Incorporate during any stage of manufacture.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
% Active 16
Weight per Gallon (lbs) 8.59
Solvent Water/PG
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
THICKENERS: EZ GEL W 16AQUEOUS SYSTEMS
• Sag and settling control with minimal viscosity build
• No activation required• Stir in at any stage of manufacturing• Excellent thermal sag resistance• Pigment suspension• Improved brushability
• Improved holdout• Improved specialty pigment orientation• Reduced pigment flooding and floating• Non-yellowing• Minimal effect on gloss and color• Excellent package stability
#1 CASTOR OIL is a technical grade castor oil for a variety of industrial applications.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Pale Yellow
Color (Gardner) 3 Max
Acid Value 2.0 Max
Viscosity (CPS) 500-700
Viscosity Stokes 6.3-8.9
Specific Gravity 0.955-0.965
Iodine Value 82-88
Hydroxyl Value 160-168
Saponification Value 176-184
Pour Point (F) -10
Moisture and Volatile 0.35% Max
Insoluble Impurities 0.01% Max
Refractive Index 1.476-1.479
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: #1 CASTOR OILTECHNICAL GRADE CASTOR OIL
T 31® OIL is a highly refined castor oil for specific applications which require maximum purity, minimum acidity and minimum moisture.
Application: Can be used in liquid dielectric and urethane reactions.
Benefits:
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Clear
Color (Gardner) 1+
Acid Value 0.8 Max
Equivalent Weight 342
Viscosity (CPS) 530
Viscosity Stokes 6.3-8.9
Specific Gravity 0.955-0.965
Iodine Value 82-88
Hydroxyl Value 160
Saponification Value 180
Pour Point (F) -10
Moisture and Volatile 0.02% Max
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: T 31® OIL URETHANE GRADE CASTOR OIL
• 100% Solids• Low Viscosity• Low Moisture• Economical• Improves Moisture resistant• Broad Range Compatibility
• Plasticizer• Adhesion Promoter• Superior Wetting Agent• Improves Salt Spray
Performance
T 41 OIL is a highly refined castor oil for specific applications which require maximum purity, minimum acidity and minimum moisture.
Application: Can be used in liquid dielectric and urethane reactions.
Benefits:
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Clear
Color (Gardner) 2+
Acid Value 2 Max
Viscosity (CPS) 500-700
Viscosity (Stokes) 6.3-8.9
Specific Gravity 0.955-0.965
Iodine Value 82-88
Hydroxyl Value 160-168
Saponification Value 176-184
Pour Point (F) -10
Moisture and Volatile 0.02% Max
Insoluble Impurities 0.01% Max
Refractive Index 1.476-1.479
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: T 41 OIL URETHANE GRADE CASTOR OIL
• 100% Solids• Low Viscosity• Low Moisture• Economical• Improves Moisture resistant
• Broad Range Compatibility• Plasticizer• Adhesion Promoter• Superior Wetting Agent
T 95 OIL is a highly refined and fully reacted (TDI) castor polymer featuring light color, broad compatibility, high gloss and durability.
Application:
• Plasticizer for resins, gums, polymers• Adhesion promoter• Surface wetting agent• Lubricity agent• Penetrant• Pigment and dye dispersant• Coupling solvent
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Color (Gardner) 3
Acid Value 2
Viscosity (CPS) 12,500
Specific Gravity 0.99
Iodine Value 82
Equivalent Weight 550
Hydroxyl Value 102
Saponification Value 166
Pour Pont (F) 15
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: T 95 OIL TDI REACTED CASTOR OIL
T 500 OIL is castor oil product for industrial applications which require high purity, light color and low acidity.
Application: T 500 OIL has the ability to carry high loads without rupture of the lubricant film and offers low coefficient of friction.
The inherent lubricity properties allow it to be used as a stand alone lubricant for compressors, vacuum pumps and continuous casting operations. It can also be used as an additive for fuels and synthetic or oil based metal working fluids.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Appearance Clear
Color (Gardner) 2 Max
Acid Value 0.8 Max
Viscosity (CPS) 500-700
Viscosity Stokes 6.3-8.9
Specific Gravity 0.955-0.965
Iodine Value 82-88
Sapon Value 176-184
Pour Pont (F) -10
Moisture and Volatile 0.25% Max
Insoluble Impurities 0.01% Max
Refractive Index 1.476-1.479
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: T 500 OIL TDI REACTED CASTOR OIL
MS PASTE is a moisture scavenger for urethane coatings, castable systems and adhesives.
It is a 50% concentration of molecular sieves powder (crystalline Aluminosilicate of Zeolite) in castor oil. It has been specifically designed for use in solvent-free polyurethane systems.
Applications: MS PASTE molecular sieves selectively absorb small polar molecules while excluding large organic molecules. In practice, MS PASTE molecular sieves will absorb water, not solvents or resins.
Typical Use Level: In polyurethane systems, approximately 2.5% - 5.0% MS PASTE is typically required based on total formulation.
Typical Properties:
Eagle Specialty Products · 2216 North Broadway · St. Louis, MO 63102(314) 241-7771 · (888) 241-9802 · Fax: (314) 241-5356
www.espinc.us
Content of Active Zeolite 50%
Pore Diameter 3A
Particle Diameter 2-8 m
Sieve Residue (42 microns) 0.1%
Specific Density (68°F) 78 per cubic foot
Viscosity (CPS at 77°F) 13000 ± 2000
Water Absorption (68°F, 50% r.h.) approximately 12%
lbs per Gallon 10.1 ± 0.2
Our data is based on laboratory tests which are believed to be accurate. However, all recommendations are made without warranty since the conditions of use are beyond the control of Eagle Specialty Products. We do not assume any liability of the product relative to performance or injury resulting from its use. Liability, if any, is limited to replacement product.
SPECIALTY OILS: MS PASTEMOISTURE SCAVENGER