Table of Contents

Committees

A-01. Powder ManufacturingA New General Equation of Mean Particle Size for Different Atomization ProcessesY.Z. Liu and Y.Y. Li 1

Acid-Insoluble Substances in Reduced Iron Powder from OresC.L. Wang and C.G. Zhang 5

Aerosol Synthesis and Growth Mechanism of Magnetic Iron NanoparticlesD. Kim, E.S. Vasilieva, A.G. Nasibulin, D.W. Lee, O.V. Tolochko and B.K. Kim 9

Atomization Using a Pressure-Gas-AtomizerL. Achelis, V. Uhlenwinkel, S. Lagutkin and S. Sheikhaliev 13

Characteristics of (Fe, M)S2 (M=Co, Ni, Mo) Composite Powders Fabricated by MCPW.H. Jung, D.K. Park, K.C. Jung, S.H. Suck, I.S. Ahn and K.W. Kim 17

Characteristics of Porous YAG Powders Fabricated by PVA Polymer Solution TechniqueS.J. Lee, P.W. Shin, J.W. Kim and S.Y. Chun 21

Characterization of GaP Nanowires Synthesized by Chemical Vapor DepositionK.K. Cho, K.H. Choi, K.W. Kim, G.B. Cho and Y.Y. Kim 25

Consideration of Fe Nanoparticles and Nanowires Synthesized by Chemical VaporCondensation ProcessJ.K. Ha, K.K. Cho, K.W. Kim, T.H. Nam, H.J. Ahn and G.B. Cho 29

Development of High Performance Stainless Steel PowdersC. Schade and J. Schaberl 33

Dry Coated Particle for Plasma SprayingC. Briones-Rodríguez, V. Mayagoitia and R. Cuenca-Alvarez 37

Effect of FeNi30 Powder Catalyst by Water Atomizing on Synthesis High-Grade DiamondD.K. Cheng, H.Q. Ma, D. Cao and F.C. Ding 41

Fabrication of Nano-Sized Titanate Powders by an Ethylene Glycol Solution RouteS.J. Lee, M.J. Lee and Y.S. Yoon 45

Fabrication of Porous Structure of BCP Sintered Bodies Using Microwave AssistedSynthesized HAp Nano PowderM.H. Youn, R.K. Paul, H.Y. Song and B.T. Lee 49

Formation of Rod-Like Al2TiO5 Via Mechanical Activation Followed by ThermalProcessingX.H. Chen, X.M. Chen, H. Zhao and J.H. Wu 53

High Efficient Metal Powder Production by Gas Atomisation ProcessR. Ünal and M. Aydın 57

High Oxygen Sensitivity of Nanocrystalline Ceria Prepared by Thermochemical ProcessD.W. Lee, J.H. Yu, T.S. Lim and T.S. Jang 61

HRTEM Study of Phase Transformation from Anatase to Rutile in Nanocrystalline TiO2ParticlesK.H. Kim, H. Park, J.P. Ahn, J.C. Lee and J.K. Park 65

Hybrid Atomization Method for Manufacturing Fine Spherical Metal PowderK. Minagawa, H. Kakisawa and K. Halada 69

Hydrogen Storage Properties of Nb-Zr-Fe Alloys Disintegrated by Hydrogen GasH. Okuyama, M. Uda, T. Uchikoshi, T.S. Suzuki and Y. Sakka 73

Hydrothermal Synthesis of Rod-Like Copper Oxide CrystalsJ.H. Pee, D.W. Lee, U. Kim and E.S. Choi 77

In-Situ TEM Observation on Phase Formation of TiO2 Nanoparticle Synthesized by FlameMethodH. Park, H.S. Jie, K.H. Kim, J.P. Ahn and J.K. Park 81

Large Scale Production of Nanoparticles by Laser PyrolysisA. Reau, B. Guizard, C. Mengeot, L. Boulanger and F. Ténégal 85

Microstructure and Properties of Plasma Spray Coatings Prepared from Ti-Zr-NiQuasicrystalline PowdersH.K. Seok, Y.C. Kim, F. Prima and E. Fleury 89

Milling and Sintering Behavior of the Metal-Ceramic Mixed PowdersZ.X. Yang, S.H. Youn, K.H. Hwang, S.Y. Yoon, J.K. Lee and H. Kim 93

Organic-Inorganic Nano Composite Membranes of Sulfonated Poly(ether Sulfone-Ketone)Copolymer and SiO2 for Fuel Cell ApplicationD.H. Lee, H.S. Park, D.W. Seo and W.G. Kim 97

Particle Size and Shape Analysis the Key to Success in Metal Powder ProductionA. Pankewitz, C. Behrens, U. Kesten and Y.J. Park 101

Preparation and Characterization of Ag/TiO2-xNx NanoparticlesZ.Q. Liu, Z.H. Li, Y.P. Zhou and C.C. Ge 105

Preparation and Characterization of Monodispersed and Nano-Sized Cu PowdersT.W. Kim, H.M. Lee, Y.Y. Kim, K.H. Hwang, H.C. Park and S.Y. Yoon 109

Preparation and Characterization of Monosized Germanium Micro Particles by PulsatedOrifice Ejection MethodS. Masuda, K. Takagi, W. Dong and A. Kawasaki 113

Preparation and Characterization of Stable Dispersions of Ni NanoparticlesE.H. Lee, M.K. Lee and C.K. Rhee 117

Synthesis and Characterization of Branched Sulfonated Poly(ether Sulfone-Ketone)Copolymer and Organic-Inorganic Nano Composite MembranesD.H. Lee, H.S. Park, D.W. Seo, T.W. Hong, S.C. Ur and W.G. Kim 121

Synthesis and Properties of Multimetal Oxide Nanopowders via Nano-Explosive TechniqueO. Vasylkiv, Y. Sakka and V. Skorokhod 125

Synthesis of Aluminum Monohydroxide Nanofiber by Electrolysis of Aluminum PlatesS.H. Woo, M.K. Lee and C.K. Rhee 129

Synthesis of Cu-Coated Ni-Based Amorphous Composite Powders by Gas Atomization andSpray Drying ProcessB.K. Kim, Y.J. Kim and J.C. Kim 133

Synthesis of Nano Metal Powder by Electrochemical Reduction of Iron OxidesK.H. Seong and J.S. Lee 137

Synthesis of Ultra Fine TiC Powders by Carbothermal ReductionB.S. Kim, Y.C. Woo and D.J. Kim 141

The Atmosphere Effect on Synthesis of TiB2 Particles by Carbothermal ReductionS.H. Kang, B.S. Kim and D.J. Kim 145

The Development of Mono-Sized Micro Silicon Particles for Spherical Solar Cells byPulsated Orifice Ejection MethodW. Dong, S. Masuda, K. Takagi and A. Kawasaki 149

The Optimization of Hydrogen Reduction Process for Mass Production of Fe-8wt%NiNanoalloy PowderS.S. Jung, Y.S. Kang and J.S. Lee 153

The Synthesis of Maghemite and Hematite (γ-Fe2O3, α-Fe2O3) NanospheresM.A. Dar, S.G. Ansari, R. Wahab, Y.S. Kim and H.S. Shin 157

Thermoelectric Properties of n-Type 90% Bi2Te3+10%Bi2Se3 Thermoelectric MaterialsProduced by Melt Spinning Method and SinteringT.S. Kim and B.S. Chun 161

Vacuum Carburization of Nanometer Tungsten Powder with Carbon BlackL. Ji, L. Tao, Z.M. Guo and C.C. Jia 165

A-02. Mechanical AlloyingCharacteristics of Nanostructured WO3-CuO Powder Mixture Produced by Ball MillingH. Azimi, E. Ahmadi and S.M.M. Hadavi 169

Effect of Ag on the Thermoelectric Properties of Ag2Se Alloy Prepared by MechanicalAlloying ProcessW.K. Min, H.D. Hwang, C.H. Lee, I.M. Park and Y.H. Park 173

Effect of Fe Doping on Thermoelectric Properties of Mechanically Alloyed CoSb3S.C. Ur, J.C. Kwon and I.H. Kim 177

b Progress in Powder Metallurgy

Fabrication of Aluminum/Aluminum Nitride Composites by Reactive Mechanical AlloyingS.H. Yu and K.S. Shin 181

Fabrication of TiH2 Powders from Titanium Tuning Chip by Mechanical MillingJ.M. Jang, W.S. Lee and S.H. Ko 185

Formation of Fe3AlC Base Alloy by Mechanical Alloying and Vacuum Hot PressingK. Isonishi 189

High Energy Ball Milling of Catalytically Synthesized Carbon NanotubesJ.H. Ahn, Y.J. Kim, S.J. Hwang and H.S. Chung 193

Mechanical Milling of Lithium with Metal Oxide and its Reactivity with GasesT. Yokoi, E. Yamasue, H. Okumura and K.N. Ishihara 197

Mechanochemical Synthesis of Zinc Ferrite, ZnFe2O4Y. Sawada, K. Iizumi, T. Kuramochi, M.H. Wang, L.X. Sun, S. Okada, K. Kudou, T. Shishidoand J. Matsushita 201

Mg-Y-Cu Bulk Metallic Glass Obtained by Mechanical Alloying and Powder ConsolidationP.Y. Lee, C.F. Hsu and C.C. Wang 205

Nanocrystalline and Ultrafine Grained Materials by Mechanical AlloyingE. Wang and L.X. Hu 209

Precipitation Behavior of γ" in Severely Plastic Deformed Ni-Base AlloysI.H. Kim and S.I. Kwun 213

Sintering Behavior of TiC-Fe Based Composite Fabricated by Spark Plasma SinteringUsing TiH2 Graphite PowdersS.Y. Bae, I.S. Ahn, H.J. Cho, C.J. Kim and D.K. Park 217

Solid-State Synthesis of Mg2X (X=Si, Ge, Sn and Pb) via Bulk Mechanical AlloyingT. Aizawa and R.B. Song 221

Synthesis of Titanium Carbide by Heat Treatment of TiH2 and Carbon Black PowdersI.S. Ahn, S.Y. Bae, H.J. Cho, C.J. Kim and D.K. Park 225

The Magnetic and Photo-Catalytic Properties of Fe Doped TiO2 Nanocrystalline PowderSynthesized by Mechanical AlloyingY.R. Uhm, S.H. Woo, M.K. Lee and C.K. Rhee 229

Thermal Stability of Amorphous Ti- Cu- Ni- Sn Prepared by Mechanical AlloyingN.T.H. Oanh, P.P. Choi, J.S. Kim, D.H. Kwon and Y.S. Kwon 233

B-01. Powder CompactionAnalysis of Failure Mechanisms during Powder CompactionC.Y. Wu, A.C. Bentham and A. Mills 237

Anisotropy of Thermal Expansion Coefficient of Pressed Graphite Foam Measured over theTemperature Interval 20-500°CI. Zerrouk, S.G. Ionov, V.P. Popov and S. Hamamda 241

Carbon Nanotube Reinforced Metal Matrix Nanocomposites via Equal Channel AngularPressingQ. Pham, Y.G. Jeong, S.C. Yoon, S.I. Hong, S.H. Hong and H.S. Kim 245

Compaction of Ultra-Fine WC Powder by High-Speed Centrifugal Compaction ProcessH.Y. Suzuki, Y. Kadono and H. Kuroki 249

Densification and Conolidation of Powders by Equal Channel Angular PressingS.C. Yoon, S.I. Hong, S.H. Hong and H.S. Kim 253

Densification Behavior of Iron Powder during Cold Stepped CompactionC.S. Kang, S.C. Lee, K.T. Kim and O. Rozenberg 257

Densification Mechanism of Warm Compaction for Iron-Based Powder MaterialsS.G. Qu, Y.Y. Li, W. Xia and W.P. Chen 261

Development of High Strength Sintered Steel by High Pressure Warm Compaction UsingDie Wall LubricationN. Matsumoto, T. Miyake, M. Kondoh, K. Ando and H. Tanino 265

Development of Optical Device Housing Compacted Using SUS304L Granulated PowdersH. Suzuki, T. Hara, Y. Ogino, Y. Sato and Y. Tomota 269

Effect of Polymer Compatibility on the Binder Migration during Spray Drying andCompaction BehaviorU. Kim, D.K. Kim, W. Carty, J.H. Pee and E.S. Choi 273

Materials Science Forum Vols. 534-536 c

Fabrication of Continuously Porous t-ZrO2 Bodies Using Carbon Powder and EvaluateTheir BiocompatibilityA.K. Gain, H.Y. Song and B.T. Lee 277

Fabrication of Rod type Cu54Ni6Zr22Ti18 Bulk Amorphous Alloy by Warm ExtrusionProcessS.C. Lim, K.H. Kim, H.B. Lee, H.S. Lee and H.C. Kwon 281

Flow Patterns in Green Bodies Made by High-Speed Centrifugal Compaction ProcessH.Y. Suzuki, K. Urabe, T. Takano and H. Kuroki 285

Green Body Behaviour of High Velocity Pressed Metal PowderP. Jonsén, H.Å. Häggblad, L. Troive, J. Furuberg, S. Allroth and P. Skoglund 289

High Velocity Compaction : Overview of Materials, Applications and PotentialF. Dore, L. Lazzarotto and S. Bourdin 293

Investigation of Mechanical Properties of Powder Metallurgy Parts with Control ofMicrostructureH. Khorsand and S.M. Habibi 297

Numerical Simulation of Cold Compaction of 3D Granular PackingsY. Chen, D. Imbault and P. Dorémus 301

Plastic Behaviour of Green Powder Metallurgical CompactsJ.M. Prado 305

Reduced Weight Scatter with Bonded Powder MixesD. Edman, L. Alzati, G. Pozzi, C. Frediani and R. Crosa 309

Segregation-Free Premixes for Increased Productivity and Improved PerformanceG. Poszmik and K.S. Narasimhan 313

Surface Densification Coupled with Higher Density Processes Targeting High-PerformanceGearingF. Hanejko, A. Rawlings, P. King and G. Poszmik 317

The Application of P/M Advanced Techniques to Sintered GearsC.X. Bao, Z.Q. Shen and Z.P. Shu 321

The Elastic Behaviour of Metal Powder CompactsJ.M. Prado 325

Warm Compaction: FEM Analysis of Stress and Deformation States of Compacting Dieswith Rectangular Profile of Various Aspect RatioE. Armentani, G.F. Bocchini, G. Cricrì and R. Esposito 329

Warm Compression of Al Alloy PM BlendsZ. Jiang, C.L. Falticeanu and I.T.H. Chang 333

B-02. Powder Injection MouldingA Study of Ceramic Injection Molding of Watch Case Composed of ZrO2 PowderT.S. Kwak 337

Computer Aided Engineering Design of Powder Injection Molding Process for a DentalScaler Tip Mold DesignC.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung and B.O. Rhee 341

Development of Dental Scaler Tip Mold with Powder Injection Molding ProcessC.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung and B.O. Rhee 345

Effect of Particle Size in Feedstock Properties in Micro Powder Injection MoldingE.R. Baek, S. Supriadi, C.J. Choi, B.T. Lee and J.W. Lee 349

Effect of Residual Carbon on the Microstructure Evolution during the Sintering of M2 HSSParts Shaping by Metal Injection Moulding ProcessG. Herranz, B. Levenfeld and A. Várez 353

Fabrication of Ti-6Al-7Nb Alloys by Metal Injection MoldingY. Itoh, H. Miura, K. Sato and M. Niinomi 357

Gas Nitriding Mechanism in Titanium Powder Injection Molded ProductsT. Osada, H. Miura, T. Yamagami, K. Nishiyabu and S. Tanaka 361

Influence of the Morphology and Particle Size on the Processing of Bronze 90/10 Powdersby Metal Injection Moulding (MIM)J.M. Contreras, A. Jiménez-Morales and J.M. Torralba 365

Innovations in Micro Metal Injection Molding Process by Lost Form TechnologyK. Nishiyabu, Y. Kanoko and S. Tanaka 369

d Progress in Powder Metallurgy

Metal and Ceramic Micro Components Made by Powder Injection MoldingV. Piotter, G. Finnah, B. Zeep, R. Ruprecht and J. Haußelt 373

Metal Injection Molding Process of Mo2FeB2 Boride Base CermetsH. Tashiro, K. Hirata, Y. Yamasaki and K. Takagi 377

Micro Metal Injection Molding Using Hybrid Micro/Nano PowdersK. Nishiyabu, K. Kakishita and S. Tanaka 381

Optimization of Composite MIM Feedstock Rheological Behaviour by ExperimentalAnalysisC.C. Chen, C.W. Wu and C.M. Yen 385

B-03. Powder ForgingEffect of Cu and Mg on Forging Property and Mechanical Behavior of Powder Forged Al-Si-Fe Based AlloyD.S. Lee, T.K. Jung, M.S. Kim and W.Y. Kim 389

Fabrication of Micro Spur Gear in Nano Grained Al AlloyW.S. Lee, J.M. Jang and S.H. Ko 393

Numerical Simulation and Forecasting of Mechanical Properties for Multi-ComponentNonferrous Dispersion-Hardened Powder MaterialsL. Ryabicheva and D. Usatyuk 397

B-04. Spray FormingAlumina-Titania Spot Spraying Bead Formation and Characteristics in AtmosphericPlasma SprayingH.S. Joo, H.S. Choi, H.H. Jo, H. Cho, J.S. Kim and C.H. Lee 401

An Empirical Method to Evaluate the In-Flight Particle Behaviors within a Cross Section ofMass Flux during Atmospheric Plasma SprayingH.S. Choi, H.S. Joo, K.M. Lim, H.H. Jo and C.H. Lee 405

Correlations between In-Flight Particles, Splats and Coating Microstructures of Ni20CrThermally Sprayed by Flame and Arc Spray ProcessesP. Apichayakul, S. Wirojanupatump and S. Jiansirisomboon 409

Effect of Gun Nozzle Geometry, Increase in the Entrance Convergent Section Length andPowder Injection Position on Cold Sprayed Titanium CoatingsK. Sakaki, S. Shinkai, N. Ebara and Y. Shimizu 413

Experimental Investigation and Modeling of the Specific Enthalpy Distribution in a SprayConeN. Ellendt and V. Uhlenwinkel 417

Fabrication of Ti(Al,O)-Al2O3 Powder Feedstock for Thermal Spraying and Evaluation ofComposite CoatingP. Cao, B. Gabbitas, L. Zheng and D.L. Zhang 421

Microstructure and Bonding Strength of Tungsten Coating Deposited on Copper by PlasmaSprayingS.X. Song, Z.J. Zhou, J. Du, Z.H. Zhong and C.C. Ge 425

Porosity in Spray-Formed MaterialsV. Uhlenwinkel and N. Ellendt 429

Present Status and Future Prospects of Cold SprayingF. Gaertner, T. Schmidt and H. Kreye 433

Spray Forming of Mg2Si Rich Aluminum AlloysN. Ellendt, V. Uhlenwinkel, O. Stelling, A. Irretier and O. Kessler 437

Study on Metal/Diamond Binary Composite Coatings by Cold SprayH.J. Kim, D.H. Jung, J.H. Jang and C.H. Lee 441

The Effect of In-Flight Bulk Metallic Glass Particle Temperature on Impact Behavior andCrystallizationS.K. Kim, S.H. Yoon and C.H. Lee 445

Ti-Based Quasicrystal Layers Produced by Plasma Thermal SprayingA. Takasaki, S. Uematsu and K.F. Kelton 449

B-05. Rapid Prototyping

Materials Science Forum Vols. 534-536 e

3D Printing of Biocompatible PM-MaterialsM. Dourandish, D. Godlinski and A. Simchi 453

Characteristics of Laser Aided Direct Metal Powder Deposition Process for Nickel-BasedSuperalloyK. Zhang, W.J. Liu and X.F. Shang 457

Direct Metal Laser Sintering – New Possibilities in Biomedical Part ManufacturingJ. Kotila, T. Syvänen, J. Hänninen, M. Latikka and O. Nyrhilä 461

Establishment of Laser Sintering Technique for Titanium PowderH. Miura, H. Maeda, M. Uemura, T. Takemasu and M. Otsu 465

High-Throughput Preparation and Characterization of Powder and Thin-Film Library forElectrode MaterialsK. Fujimoto, K. Onoda and S. Ito 469

Micro Fabrication Process of Powder Compact with Semi-Solid MoldF. Tsumori 473

Three-Dimensional Printing of Shape Memory AlloysE. Carreño-Morelli, S. Martinerie and J.E. Bidaux 477

B-06. SinteringA Solution for Diffusion Equations and the Distribution of Alloying Elements in SinteredAlloysC.L. Wang 481

Abnormal Grain Growth Mechanism of Calcium Hexaluminate PhaseJ.H. Song, Y.J. Jo, H.G. Bang and S.Y. Park 485

An Investigation on the Sintering Behavior of High Strength Al-Zn-Mg-Cu Alloy Preparedfrom Elemental PowdersM. Shahmohammadi, A. Simchi, H. Danninger and A. Arvand 489

Analysis of Particle Rearrangement during Sintering by Micro Focus ComputedTomography (µCT)M. Nöthe, M. Schulze, R. Grupp, B. Kieback, A. Haibel and J. Banhart 493

Assessment of the Corrosion Behavior of a Sintered Al-Cu-Mg Alloy in AeronauticalEnvironments as a Function of the Heat TreatmentS. Sánchez-Majado, J.M. Torralba and A. Jiménez-Morales 497

Consolidation of Bulk Metallic Glass CompositesJ.K. Lee, H.J. Kim, T.S. Kim, S.Y. Shin and J.C. Bae 501

Densification Behavior and Microstructural Development of Nano-Agglomerate Powderduring SinteringY.S. Kang, B.H. Cha, H.G. Kang and J.S. Lee 505

Densification Behaviors of Fe-TiC System during Spark Plasma SinteringY. Lee, D.K. Park, S.Y. Bea and I.S. Ahn 509

Effect of the Preparation Methods of Me+Al Powder Blends on the Compaction Behavior,Structure, Phase Transformations, and Properties of the Compacted Aluminides ofTransition MetalsK.B. Povarova, N.K. Kazanskaya, A.A. Drozdov, A.E. Morozov and A.G. Nikolaev 513

Expansion Behavior of Iron-Copper Compact from (FeCu) Pre-Alloyed PowderY.C. Kim and M.J. Suk 517

Fabrication of Deep-Sub-Millimeter-Thick Compacts Using Spark Plasma SinteringT. Tanaka, T. Ohashi, K. Oshiro, H. Fujimori, H. Kurisu, M. Matsuura and S. Yamamoto 521

Fabrication of Nanocrystalline TaSi2-SiC Composite by High Frequency Induction HeatedCombustion Synthesis and Its Mechanical Properties.I.J. Shon, D.K. Kim, I.Y. Ko, J.K. Yoon and K.T. Hong 525

Grain Growth Kinetics of Cobalt-Doped SnO2 by Varying Nb2O5 ContentD.G. Chang, J.H. Lee and J.J. Kim 529

Grain Growth Rate in SnO2 Ceramics Doped with Varying Ratios of Nb2O5/CoOD.G. Chang, J.H. Lee and J.J. Kim 533

Improvement in Microstructure Homogeneity of Sintered Compacts through PowderTreatments and Alloy DesignsK.S. Hwang, M.W. Wu, F.C. Yen and C.C. Sun 537

f Progress in Powder Metallurgy

In Situ Observations of Sintering Process during Pulsed Current Sintering of Al2O3, ZnOand WC AlloyY. Kawakami, F. Tamai, T. Enjoji, N. Shikatani, T. Misawa, M. Otsu and K. Takashima 541

Influence of Sintering Parameters on the Mechanical Performance of PM Steels Pre-Alloyedwith ChromiumO. Bergman, B. Lindqvist and S. Bengtsson 545

Investigation of Sintering Behaviors of Steatite Parts Produced by Powder InjectionMoldingI. Uslan, M. Berber, Ç. Karatas and S. Saritaş 549

Liquid Phase Sintering of a Boron Alloyed Austenitic Stainless SteelA. Molinari, C. Menapace, J. Kazior and T. Pieczonka 553

Low-Temperature Sintering and Electromagnetic Properties Evaluation of (Ni/Mn)CuZnFerriteD.Y. Ju and P. Bian 557

Microstructure and Tensile Properties of Tungsten Heavy AlloysS.H. Islam, X.H. Qu, F. Akhtar, P.Z. Feng and X.B. He 561

Microstructure Characteristics and Electrical Properties of Sintered (Bi,La)4Ti3O12Ferroelectric CeramicsH.S. Yoo, Y.H. Son, T.W. Hong, S.C. Ur, S.L. Ryu and S.Y. Kweon 565

Model Calculation of Grain Growth in a Liquid MatrixY.I. Jung, D.Y. Yoon and S.J.L. Kang 569

Multi-Scale Virtual Reality of SinteringE. Olevsky 573

Oxygen Removal during Sintering of Steels Prepared from Cr-Mo and Mo PrealloyedPowdersH. Danninger, C. Xu and B. Lindqvist 577

Preparation and Properties Study of Cu-MoSi2 CompositesX. Yi, W.H. Xiong and J. Li 581

Preparation and Sintering Behavior of Fe Nanopowders Produced by Plasma Arc DischargeProcessC.J. Choi and J.H. Yu 585

Pulsed Electric Current Sintering of Nano-Crystalline Iron-Base PowdersY.Y. Li, Y. Long, X.Q. Li and Y.Z. Liu 589

Research on Two Sintered Techniques of Nanometer WC-Co PowderL. Sun, C.C. Jia and H. Tang 593

Sintering Behaviour of Al-Cu-Mg-Si BlendsC.L. Falticeanu, I.T.H. Chang, J.S. Kim and R. Cook 597

Synthesis and Densification of Nanostructured Al2O3-(Zro2+3%Mol Y2O3) Bioceramics byHigh-Frequency Induction Heat SinteringS.W. Kim and K.A. Khalil 601

The Effect of MgO-Y2O3 on Al2O3-TiC CompositesS. Kasuriya and D. Atong 605

True Sedimentation and Particle Packing Rearrangement during Liquid Phase SinteringJ.K. Lee, L. Xu and S.Z. Lu 609

B-07. Post Sintering ProcessesA New Technology of Hardening Porous Materials of Titan PowdersK.E. Belyavin, D.V. Minko and N.V. Reshnetikov 613

A Preliminary Study of the Development of 9Cr Fe-Base ODS Alloys: The Effects of MinorElements and Cooling RateJ.S. Jang, Y.M. Jang and Y.Z. Shen 617

Fabrication of Cordierite Honeycomb from Fly AshS.J. Kim, S.J. Park, H.G. Bang and S.Y. Park 621

Hardenability of Low Alloy Sintered Mn SteelsM. Zendron, A. Molinari and L. Girardini 625

Influence of Tempering Temperature and Microstructure on Wear Properties of Low AlloyPM Steel with 1-2 % Ni AdditionS. Tekeli, A. Güral and M. Gürü 629

Materials Science Forum Vols. 534-536 g

Sinter-Bonding of Iron Based Compacts Containing P and CuT. Pieczonka and J. Kazior 633

Study for the Development of Fe-NbC Composites by Advanced PM TechniquesE. Gordo, B. Gómez, R. González and E.M. Ruiz-Navas 637

C-01. SteelsAn Investigation on Elongation-Porosity Relation in Sintered 17-4 PH Stainless SteelH.J. Sung, T.K. Ha, S.H. Ahn and Y.W. Chang 645

Application Experiences in Powder Compaction of Iron Powder - Influence of Tool Materialon Tool LifeO. Sandberg, A. Krona, S. Berg, F. Kaad and G. Nord 649

Capabilities of Two Chromium Powder Metallurgy Steels for High PerformanceApplications at Conventional Sintering TemperaturesP. King and B. Lindsley 653

Comprehensive Wear Study on Powder Metallurgical Steels for the Plastics Industry,Especially Injection Moulding MachinesC. Gornik and J. Perko 657

Development of PM Stainless Steels with Improved Properties through Liquid PhaseSinteringC. Tojal, T. Gómez-Acebo and F. Castro 661

Dimensional Precision in Sinter-Hardening PM SteelsB. Lindsley and T. Murphy 665

Effect of Heat Treatment Conditions and Densities on Residual Stresses at Hybrid (FLN2-4405) P/M SteelsF. Kafkas, Ç. Karatas and S. Saritaş 669

Effect of Repeated Quenching Heat Treatment on Microstructure and Dry Sliding WearBehavior of Low Carbon PM SteelA. Güral, S. Tekeli, D. Özyürek and M. Gürü 673

Fatigue Properties for Sinter-Hardened Fe-Ni-Mo-Cu MaterialsC.L. Wang, P. Wang and Z.M. Shi 677

Functional Relationships between Fatigue DataP. Beiss 681

Gigacycle Fatigue Crack Initiation in Cr-Mo Prealloy Sintered SteelC. Xu, H. Danninger, G. Khatibi and B. Weiss 685

Gigacycle Fatigue Endurance Strength of High Density Mo and Cr-Mo Prealloyed SinteredSteelC. Xu, H. Danninger, G. Khatibi and B. Weiss 689

Influence of Binders on the Structure and Properties of High Speed-Steel HS6-5-2 TypeFabricated Using Pressureless Forming and PIM MethodsG. Matula, L.A. Dobrzański, G. Herranz, A. Várez, B. Levenfeld and J.M. Torralba 693

Modification of Low Alloyed Steels by Manganese AdditionsJ. Sicre-Artalejo, M. Campos, T. Marcu and J.M. Torralba 697

Nominally Equivalent Powders for P/M Steels: Analysis of Response to Sintering andDifferences at Various C ContentG.F. Bocchini, M.G. Ienco, M.R. Pinasco, E. Stagno, A. Baggioli, R. Gerosa and B. Rivolta 701

Processing Routes for Obtaining Novel High Performance Mn-Containing PM SteelsF. Castro, M. Sarasola, S. Sainz and T. Gómez-Acebo 705

Rolling Contact Fatigue of Hot-Forged Steels out of Prealloyed Powders and Powder BlendV. Dorofeyev and A. Sviridova 709

Rolling Contact Fatigue Property of Sintered and Carburized Compacts Made ofMolybdenum Hybrid-Alloyed Steel PowderS. Unami, Y. Ozaki and S. Uenosono 713

SCC Inhibitors for SG Tube Materials in Nuclear Power PlantsK.M. Kim, E.H. Lee and U.C. Kim 717

Sintered Duplex Stainless Steels Corrosion PropertiesL.A. Dobrzański, Z. Brytan, M. Actis-Grande and M. Rosso 721

Sintered Structural Cu-Ni-Mo-C Low Alloyed Steels with Small Niobium AdditionsM. Orban and R.L. Orban 725

h Progress in Powder Metallurgy

Sintering Processing of Compressor FlangesJ.K. Park, H.S. Park and S.T. Choi 729

Sintering Stainless Steels with Boron Addition in Nitrogen Base AtmosphereJ. Abenojar, D. Esteban, M.A. Martínez and F. Velasco 733

Stable and Unstable Crack Growth in Chromium Pre-Alloyed SteelR. Gerosa, B. Rivolta, A. Tavasci, G. Silva and A. Bergmark 737

Strain Hardening Behaviour of PM Alloys with Heterogeneous MicrostructureG. Straffelini 741

Stress Corrosion Cracking of Alloys 600, 690, and 800 in a Tetrathionate Solution at 340°CE.H. Lee and K.M. Kim 745

Study of Elastic Moduli of Sintered Low Alloy Steels by Acoustic Pulse MethodN. Hirose, K. Oouchi, A. Fujiki and J. Asami 749

The Effect of Chemical Composition of Sintering Atmosphere on the Structure andMechanical Properties of PM Manganese Steels with Chromium and MolybdenumAdditionsM. Sulowski, A. Cias, M. Stoytchev and T. Andreev 753

The Effect of Cooling Rate on the Structure and Mechanical Properties of Fe-3%Mn-(Cr)-(Mo)-C PM SteelsM. Sulowski, A. Cias, H. Frydrych, J. Frydrych, I. Olszewska, R. Golen and M. Sowa 757

The Sintering Behaviour of Fe-Mn-C Powder System, Correlation betweenThermodynamics and Sintering Process, Mn Distribution and MicrostructureE. Hryha and E. Dudrová 761

C-02. Light AlloysA Comparative Study of Mechanical Property in Al-8Fe-2Mo-2V-1Zr Bulk AlloysFabricated from an Atomized Powder and a Melt Spun RibbonT.K. Jung, T.J. Sung, M.S. Kim and W.Y. Kim 765

A Study of Debinding Behavior and Microstructural Development of Sintered Al-Cu-SnAlloyJ.S. Kim, I.T.H. Chang, C.L. Falticeanu, G.J. Davies and K. Jiang 769

Aluminium and Aluminium Alloy Powders for P/M ApplicationsR. Cook, I.T.H. Chang and C.L. Falticeanu 773

Blended Elemental P/M Synthesis of Titanium Alloys and Titanium Alloy-Based ParticulateCompositesM. Hagiwara and S. Emura 777

Development of P/M Aluminum Alloy with Fine MicrostructureT. Tokuoka, T. Kaji and T. Nishioka 781

Effect of High-Energy Ball Milling on the Mg Alloy Powders under Alcohol ProtectionG. Li, X.X. Liu, Q. Guo, J.R. Tang and B. Yan 785

Effect of Porosity Content on the Weldability of Powder Metal Parts Produced by FrictionStir WeldingA. Kurt, I. Uygur and H. Ates 789

Effect of Powder Size of Mg-Zn-Y Alloy on the ConsolidationT.S. Kim, H.J. Chae, J.K. Lee, H.G. Jeong, Y.D. Kim and J.C. Bae 793

Effect of Powder Size on Infiltration Height in Producing MgO Reinforced Al MatrixComposite by Vacuum Infiltration MethodR. Calin and R. Citak 797

Extrusion of CP Grade Titanium Powders Eliminating the Need for Hot Pre-Compactionvia Hot Isostatic PressingR. Wilson, N.A. Stone and M.A. Gibson 801

Fabrication of TiAl Target by Mechanical Alloying and Applications in Physical VapourDeposition CoatingB. Gabbitas, P. Cao, S. Raynova and D.L. Zhang 805

Gas Chromatographic Analysis of Degassing of Aluminum and Aluminum Alloy PowdersR. Watanabe, D.S. Choi and A. Kawasaki 809

Influence of High-Energy Milling and Sintering Cycle on Obtaining TiAl from Elemental Tiand Al PowdersP.G. Esteban, E. Gordo and E.M. Ruiz-Navas 813

Materials Science Forum Vols. 534-536 i

Interactions in Titanium Matrix Composites Reinforced by Titanium Compounds byConventional PM RouteF. Romero, V. Amigó Borrás, M.D. Salvador and A. Vicente 817

Macro-Interface Characteristics of Bimodal-Structured Al Materials Produced by Ball-MillingS.Y. Chang, H.G. Cho, J.C. Kim, S.H. Lee and B.H. Song 821

Mechanical and Microstructural Properties of Titanium Matrix Composites Reinforced byTiN ParticlesF. Romero, V. Amigó Borrás, M.D. Salvador and E. Martinez 825

Microstructure and Properties of Zn61Al34M5 Alloy Produced by Rapid Solidification andWarm-Compacting Sintering ProcessH.Y. Lou, W. Lu, L. Yang and B. Yan 829

Microstructures and Mechanical Properties of Consolidated Mg-Zn-Y AlloyJ.K. Lee, T.S. Kim, H.G. Jeong and J.C. Bae 833

Softening-Hardening Mechanism in the Direct Hot-Extrusion of Aluminium CompactsC. Zubizarreta, I. Arribas, S. Giménez and I. Iturriza 837

Study of TiCn Additions to an 2xxx Series Aluminium AlloyE.M. Ruiz-Navas, M.L. Delgado, S. Benito Gonázles and E. Gordo 841

The Influence of Heat Treatment on Corrosion Resistance of PM Composite MaterialsBased on EN AW-AlCu4Mg1(A) Aluminium Alloy Reinforced with the Ti(C,N) ParticlesL.A. Dobrzański, A. Włodarczyk-Fligier and M. Adamiak 845

C-03. Composite MaterialsAging Characteristics of Al P/M Composites with Variation of Ceramic ContentsK.H. Min, S.Y. Chang, D.S. Kim, J.S. Kim and Y.D. Kim 849

Carbon-Nanofiber Reinforced Cu Composites Prepared by Powder Metallurgy for ThermalManagement of Electronic DevicesH. Weidmueller, T. Weissgaerber, T. Hutsch, R. Huenert, T. Schmitt, K. Mauthner and J. Schulz-Harder 853

Compressive Behavior of 7xxx Series Al Composites Reinforced with Al2O3Y.I. Seo, K.H. Min, K.H. Lee and Y.D. Kim 857

Creep Behavior of Hot Extruded Al-5% SiC Composite PowderA. Hosseini Monnazah, A. Simchi and S.M. Seyed Reihani 861

Effect of Carbon-Nanotube Addition on Thermal Stability of Ti-Based Metallic GlassCompositesC.F. Hsu and P.Y. Lee 865

Effect of Cutting Tool Materials on Surface Roughness and Cutting Forces in Machining ofAl-Si3N4 Composite Produced by Powder MetallurgyY. Ozcatalbas, E. Bahceci and M. Turker 869

Effect of Hot-Forging on NiTi Shape Memory Alloy Fibers Reinforced Mg Alloy CompositeQ. Guo, G. Li, J.R. Tang and B. Yan 873

Effect of Post Deformation on the Structure and Properties of Sintered Al-Cu-SiCCompositesH.S. Chung, R.M. Heo, M.T. Kim and J.H. Ahn 877

Elaboration by Tape Casting and Hot Rolling of Copper/Silicon Carbide Composite ThinFilms for Microelectronic ApplicationsP.M. Geffroy, J.F. Silvain and T. Chartier 881

Fabrication of Al2O3/Cu Nanocomposites by Atmosphere-Controlled Sintering and TheirPropertiesS.T. Oh, Y.D. Kim and J.K. Lee 885

Fabrication of Carbon Nanotube Reinforced Aluminum Composite by Powder ExtrusionProcessJ. Yuuki, H. Kwon, A. Kawasaki, A. Magario, T. Noguchi, J. Beppu and M. Seki 889

Fabrication of CNT-Reinforced HAp Composites by Spark Plasma SinteringS.K. Sarkar, M.H. Youn, I.H. Oh and B.T. Lee 893

Hot Deformation Behavior of P/M Al6061-20% SiC CompositeH. Asgharzadeh and A. Simchi 897

j Progress in Powder Metallurgy

Investigation of Microstructure Inhomogeneity in SiCp-Reinforced Aluminum MatrixCompositesZ. Gácsi, C.H. Gür, A. Makszimus and T. Pieczonka 901

Mechanical Properties of W-X (X=Cu, Ag or BAg-8) CompositesH. Hanado, Y. Hiraoka, T. Inoue and N. Akiyoshi 905

Microstructure Characterization of SiCp-Reinforced Aluminum Matrix Composites byNewly Developed Computer-Based AlgorithmsF. Kretz, Z. Gácsi and C.H. Gür 909

Preparation of Warm Compacted NbC Reinforced Iron-Based Composite and ItsTribological BehaviorZ.Y. Xiao, T.W.L. Ngai, L.P. Wen and Y.Y. Li 913

Reaction Synthesis and Mechanical Properties of B4C-Based Ceramic CompositesJ.H. Han, S.W. Park and Y.D. Kim 917

Shock-Wave Synthesis of Titanium Diboride in Copper Matrix and Compaction of TiB2-CuNanocompositesO.I. Lomovsky, V.I. Mali, D.V. Dudina, M.A. Korchagin, D.H. Kwon, J.S. Kim and Y.S. Kwon 921

Sinter Forged MMC Components for Wear-PartsS.P. Millot 925

Studies on Preparation of Ti3SiC2 Particulate Reinforced Cu Matrix Composite by WarmCompaction and Its Tribological BehaviorT.W.L. Ngai, Z.Y. Xiao, Y.B. Wu and Y.Y. Li 929

Surface Modification of Ag Coated Cu Conductive Metal Powder for Conductive SiliconeSealant Gasket PasteS.Y. Park, T.W. Yoon, C.H. Lee, I.B. Jeong and S.H. Hyun 933

C-04. Porous and Cellular MaterialsA Study on Kinetics Parameters of Titanium Hydride Powder from Its TPD Spectrum forMetal FoamD.H. Yang, S.Y. Kim and B.Y. Hur 937

Bend Deformation Behavior of Silicon Carbide Reticulated Porous CeramicsX.W. Zhu, Y. Sakka, S.H. Tan and D.L. Jiang 941

Corelationship Between Powder Metallurgy and Casting Method Using SiC Powder forMetal FoamS.Y. Kim, N. Babcsán, D.K. Ahn, Y.H. Song and B.Y. Hur 945

Development of Some New Porous Metal MaterialsY.C. Fang, H. Wang, Y. Zhou and C.J. Kuang 949

Effect of Substrate Porosity on the Coating Adhesion of Iron Sintered Plated Parts withInfiltration PretreatmentM. Etaat, M. Ghambari and M.N. Riabi 953

Fabrication of Gas-Permeable Die Materials Having Orthogonally Arrayed Pore ChannelsT.Y. Chan, D.X. Wang, H.J. Chang and C.L. Chen 961

Fabrication of Graded Porous Structure with Pore Size Distribution by SPS ProcessM.J. Suk, W.S. Seo and Y.S. Kwon 965

Fabrication of Porous Material Using Glass Abrasive SludgeY.S. Chu, C.W. Kwon, J.K. Lee and K.B. Shim 969

Low-Cycle Fatigue Performances of P/M Ti-Fe-Mo-Al-Nd AlloyH.Y. Liu, H.P. Tang, C. Li, Y.P. Huang, B. Huang and Y. Liu 973

Micro-Porous Nickel Produced by Powder MetallurgyY. Yamada, Y.C. Li, T. Banno, Z.K. Xie and C.E. Wen 977

Net-Shape Manufacturing of Micro Porous Metal Components by Powder InjectionMoldingK. Nishiyabu, S. Matsuzaki and S. Tanaka 981

Preparation of Titanium Microfiltration Membrane by Field–Flow FractionationDepositionQ.B. Wang, H.P. Tang, Q.C. Zhang, Q.F. Qiu and J.Y. Wang 985

Processing of Polymer-Derived Microcellular Ceramics Containing Reactive FillersY.W. Kim, D.H. Jang, J.H. Eom, I.H. Song and H.D. Kim 989

Materials Science Forum Vols. 534-536 k

Production of Titanium Porous Material “Tiporous” and Its EvaluationT. Onishi, K. Azuma and T. Ogasawara 993

Recycling of Stainless Steel Grinding SludgeT. Shimizu, K. Hanada, S. Adachi, M. Katoh, K. Hatsukano and K. Matsuzaki 997

Sintered Fe3Al Intermetallic - A New Filter Element for Hot Gas FiltrationY. Xing, X. Kuang, F. Wang, C.J. Kuang and Y.C. Fang 1001

Synthesis and Properties of Open-Celled Metal FoamsP. Quadbeck, G. Stephani, K. Kümmel, J. Adler and G. Standke 1005

C-05. Ceramic MaterialsAqueous Processing of Textured Silicon Nitride Ceramics by Slip Casting in a StrongMagnetic FieldX.W. Zhu, T. Uchikoshi and Y. Sakka 1009

Biomimetic Deposition of Apatite on Zr-1Nb and Ti-6Al-4VJ. Kim, Y.C. Choi, H.S. Kim and S.I. Hong 1013

Design of Porosity Level for Porous Si3N4 Ceramics Manufactured by Nitriding and Post-Sintering of Si Powder CompactY.J. Park, E. Choi, H.W. Lim and H.D. Kim 1017

Effect of Powder Synthesis Processing on the Microstructure and Electrical Conductivity ofSintered CNTs/Fe/Al2O3 NanocompositesY.H. Choa, S.H. Yoo, J.K. Yang, J.W. Park, S.T. Oh, K.M. Kang and S.G. Kang 1021

Effects of Y2O3 Addition on the Microstructure and Electrical Property of TiO2-ExcessBaTiO3J.H. Kim and Y.H. Han 1025

Formation of Barrier Ribs via Micro Molding Process Using UV-Curable PasteY.S. Kim, T.G. Koh and Y.S. Kim 1029

High-Frequency Induction Heating Sintering of Hydroxyapatite-(Zro2+3%Mol Y2o3)BioceramicsK.A. Khalil and S.W. Kim 1033

High Temperature Stability of Bulk Ti3SiC2 Materials in AirD.H. Lee, J.H. Han, Y.D. Kim, S.W. Park and D.B. Lee 1037

Making Alumina Microcomponents From Al PowderJ.S. Kim, K. Jiang, C.L. Falticeanu, G.J. Davies and I.T.H. Chang 1041

Mechanism of the Voltage Occurrence in BSCCO SuperconductorS.H. Lee 1045

Microstructure Control of Porous In-Situ Synthesized Si2N2O-Si3N4 CeramicsR.K. Paul, C.W. Lee, H.D. Kim and B.T. Lee 1049

Nozzles from Alumina Ceramics with Submicron Structure Fabricated by Radial PulsedCompactionA. Kaygorodov, C.K. Rhee, W.W. Kim, V. Ivanov, S. Paranin, A. Spirin and V. Khrustov 1053

Phase Orientation of a TiC-TiB2-SiC Ternary Eutectic Composite Prepared by An FZMethodR. Tu, W. Li and T. Goto 1057

Polymer Derived Ceramic Seals for Application in SOFCS.J. Hong and D.J. Kim 1061

Powder Characteristics and Sintering Behavior of SiO2 Coated BaTiO3J.S. Park and Y.H. Han 1065

Preparation and Characterization of LnTaO4 (Ln = La, Nd, Sm, Dy, Er and Tm)A. Fujita, H. Matsushita and A. Katsui 1069

Preparation of Silicon Nitride-Silicon Carbide Composites from Abrasive SiC PowdersS. Kasuriya and P. Thavorniti 1073

Sintering and Mechanical Properties of Chromium Boride - Chromium CarbideCompositesJ. Matsushita, K. Shimao, Y. Machida, T. Takao, K. Iizumi, Y. Sawada and K.B. Shim 1077

Synthesis and Characterization of Delafossite CuLaO2 for Thermoelectric ApplicationY. Takahashi, H. Matsushita and A. Katsui 1081

l Progress in Powder Metallurgy

Synthesis and Mechanical Properties of Nano Laminating Cr2AlC using CrCx/Al PowderMixturesJ.H. Han, S.W. Park and Y.D. Kim 1085

The Effect of Oxygen Addition on Oxidation Resistance and Cutting Performance of Si3N4CeramicsM. Nagano, H. Sano, S. Sakaguchi, G.B. Zheng and Y. Uchiyama 1089

C-06. Diamond and cBN ToolsCharacteristics of Pre-Alloyed Powders for Diamond ToolsX.Y. Luo, M.Q. Tang, X. Kuang, M. Huang and H.Q. Ma 1093

Creation of Diamond/Molybdenum Composite Coating in Open AirY. Ando, S. Tobe and H. Tahara 1097

Diamond Tools with Diamond Grits Set in a Predetermined PatternJ.C. Sung 1101

Effect of Cobalt to Bronze Ratio on Transverse Rupture Strength of Diamond SegmentsR. Ünal 1105

Effect of Phase Transformation and Grain-Size Variation on the Dry Sliding Wear of Hot-Pressed CobaltY.S. Kim, J.E. Lee, S.H. Kang and T.W. Kim 1109

Matrix Composition Effect on the Wear Behaviour of Diamond SegmentsR. Ünal and E.A. Gurcay 1113

New Pcbn for Heavy Interrupted Cutting of Hardened SteelK. Okamura, S. Kukino and T. Fukaya 1117

Powder Metallurgy Diamond Tools – A Review of Manufacturing RoutesJ. Konstanty 1121

Resistance to Abrasive Wear of Materials Used as Metallic Matrices in DiamondImpregnated ToolsJ. Konstanty, T.W. Kim and S.B. Kim 1125

Sinetring of Cobalt - (3-25 wt.%) Iron MaterialsA. Romanski 1129

The In-Situ Dressing of CMP Pad Conditioners with Novel Coating ProtectionJ.C. Sung and M.C. Kan 1133

The Metallization of Diamond GritsJ.C. Sung, S.C. Hu and Y.S. Chang 1137

The Revolution of Diamond Synthesis TechnologyJ.C. Sung, S.C. Hu, I.C. Lin and C.C. Tsai 1141

Thermal Protection Shield Concept for Diamond Impregnated ToolsW. Tillmann, M. Gathen and C. Kronholz 1145

C-07. Hard MaterialsA Study of Reduced and Carburized Reactions in Dry-Milled WO3+Co3O4+C MixedPowders with Different Carbon ContentH.S. Im, J.M. Hur and W.J. Lee 1149

Binder-Free Tungsten Carbide Fabricated by Pulsed Electric Current SinteringK. Shimojima, H. Hosokawa, T. Nakajima, M. Mizukami and Y. Yamamoto 1153

Development of High Corrosion Resistant Mo2NiB2 Boride Base Cermets for PlasticInjection Molding Machine PartsK. Hirata, K. Iwanaga, Y. Yamasaki and K. Takagi 1157

Effect of Adding a Type of Binder Phase on The Microstructure, Properties and HeatTreatment of Steel Bonded TiC CermetsA. Farid, S.J. Guo, J.A. Shah and P.Z. Feng 1161

Effect of Secondary Carbide Addition on Properties of Ti(C0.7N0.3)-Ni CermetsS.Y. Ahn, H. Kim and S.H. Kang 1165

Effect of Sinter/HIP Technology on Properties of TiC-NiMo CermetsL. Kollo, J. Pirso and K. Juhani 1169

Effect of TiC Content on Oxidation Behavior of Sintered WC-TiC-TaC AlloysH. Tanaka, S. Mouri, K. Nakahara, H. Sano, G.B. Zheng and Y. Uchiyama 1173

Materials Science Forum Vols. 534-536 m

Effects of Inhibitors on the Synthesization of WC/Co Composite Powders byMechanochemical MethodH.S. Im, J.M. Hur and W.J. Lee 1177

Electro Discharge Compaction of WC-Co Composite Material Containing Particles ofDiamondE. Grigoriev and A. Rosliakov 1181

Fabrication of Nano-Sized WC/Co Composite Powder by Direct Reduction andCarburization with CarbonD.R. Lee and W.J. Lee 1185

Formation of Twinned WC Grains during Carbonization of Eta Phase (W3Co3C)J.D. Kim, K.W. Lee, J.W. Lee, M. Sharon and S.J.L. Kang 1189

Friction and Wear Behaviors of WC-Co/WC-Co Pairs in AirH. Hosokawa, T. Nakajima and K. Shimojima 1193

Hybrid Composite Nano-Sized WC-Co Cemented CarbideS.Y. Park and W.J. Lee 1197

Influence of Cobalt Content on the Fatigue Strength of WC-Co HardmetalsT. Nakajima, H. Hosokawa and K. Shimojima 1201

Measurement of WC Grain Size in Nanocrystalline WC-10Co HardmetalC.G. Lin and G.S. Yuan 1205

Microstructural and Mechanical Characteristics of in Situ Synthesized Chromium-Nickel-Graphite CompositesJ. Pirso, M. Viljus, S. Letunovits and K. Juhani 1209

Microstructure Features of Large Grains in WC-Co AlloysA. Delanoë, S. Lay and J.M. Missiaen 1213

On the Solubility of Chromium in Cubic Carbides in WC-Co-MC-SystemsS. Norgren, A. Kusoffsky, M. Elfwing and A. Eriksson 1217

Performance of Cemented Carbides in Cyclic Loading Wear ConditionsJ. Kübarsepp, H. Klaasen and F. Sergejev 1221

Research on Microstructure and Properties of TiN, (Ti, Al)N and TiN/(Ti, Al)N MultilayerCoatingsW.S. Quan, C. Li, Y. Fei and L. Jia 1225

Spark Plasma Sintering and Hot Pressing Sintering of Nanocrystalline WC-10CO-0.8VCL.H. Zhu, G.J. Shao, Y.X. Liu and D. Siddle 1229

Structural and Mechanical Properties of Multilayered CVD TiC/TiCN Coatings withVariations of Multilayer PeriodG.W. Park and H.S. Kwon 1233

Synthesis of WC-10wt.%Co Nanocrystalline Powders with Grain Growth Inhibitor by MTPD.K. Park, K.C. Jung, J.C. Kim, S.Y. Bae and I.S. Ahn 1237

The Effect of Substrate Surface Characteristics on AIP PVD Coating of Cemented CarbideInserts and Their Cutting PerformanceD.G. Ahn, K.W. Lee, J.W. Lee and M. Sharon 1241

The Study of Synchronous Reduction-Carbonization of V2O3, Cr2O3 and W-Co CompositeOxides in FluidizationN.Y. Gong and Y.F. Ouyang 1245

C-08. Refractory Materials & Heavy AlloyDevelopment of Tungsten Heavy Alloy with Hybrid Structure for Kinetic EnergyPenetratorW.H. Baek, E.P. Kim, H.S. Song, M.H. Hong, S. Lee, Y.M. Kim, S.H. Lee, J.W. Noh and J.H.Ryu 1249

Effect of Cu during Non-Isothermal Hydrogen Reduction of MoO3G.S. Kim, D.G. Kim, S.T. Oh, M.J. Suk and Y.D. Kim 1253

Enhancement of Microstructural Homogeneity of W-Cu Pseudo-Alloy by Adding W-CuComposite Powder in Infiltration ProcessM.H. Hong, J.H. Choi, S. Lee, E.P. Kim, J.W. Noh, S.H. Lee and Y.M. Kim 1257

Fine-Grained Tungsten Heavy Alloy by Mechanical Alloying with Yttrium Oxide AdditionJ.L. Fan, H.C. Cheng, B.Y. Huang, T. Liu and D.L. Wang 1261

n Progress in Powder Metallurgy

Influences of Doping Methods on Microstructure and Fracture Toughness of Mo-La AlloysL. Wang, Y.J. Sun, J.H. Luo, Y.G. Zhu and P.W. Niu 1265

Mechanical Properties of Refractory Metals at Extremely High TemperaturesB. Fischer, M. Beschliesser, A. Hoffmann and S. Vorberg 1269

Microstructures of W-Mo-Ni-Fe Heavy AlloysK.H. Lin, C.S. Hsu and D.X. Wang 1273

Neutron Diffraction Analysis of Tungsten-Molybdenum-Disilicide Powders Formed by Self-Propagating High Temperature SynthesisY. Choi and Y.S. Kim 1277

Porous Metals of Northwest Institute for Non-Ferrous Metal ResearchH.P. Tang, J.C. Liao and J.L. Zhu 1281

Powder Metallurgy of Tungsten AlloyK. Zhang and G.C. Chun 1285

Study on Oxidation Behavior of (W,Mo)Si2 Powders in Air at 400, 500 and 600ºCP.Z. Feng, X.H. Qu, X.H. Wang and A. Farid 1289

The Effects of Molybdenum Content on the Dynamic Properties of Tungsten-Based HeavyAlloysW.S. Lee and T.Y. Chan 1293

C-09. Magnetic MaterialsBulk Amorphous and/or Nanocrystalline Finemet Alloy Prepared by Super-High-PressureConsolidationW. Lu and B. Yan 1297

Determination of Non-Stoichiometry of Tubular Titanium Carbide Formed by Self-Propagating High Temperature SynthesisY. Choi and N.I. Cho 1301

Effect of Ba Strate Addition on Magnetic Properties of Ba-System W-Type Ferrite MagnetsH. Yamamoto, H. Nishio and Y. Sawayama 1305

Effect of Particles Size on Magnetic Performance of DielectromagneticsD. Gaworska, S.N.B. Hodgson, J. Koniarek and B. Weglinski 1309

Effects of Crystal Grain Size and Particle Size on Core Loss for Fe-Si Compressed CoresS. Takemoto and T. Saito 1313

Evaluation of DC Brush-Less Motors Using Powder Magnetic CoresK. Mori, R. Nakayama and K. Kanagawa 1317

Improved Magnetic Properties of Silicon-Iron Alloy Powder CoreT.K. Lee, G.H. Kim, G.B. Choi, I.B. Jeong, K.Y. Kim and P.W. Jang 1321

Improvement of Super Low Core-Loss Soft Magnetic MaterialsT. Maeda, A. Sato, Y. Mochida, H. Toyoda, K. Mimura and T. Nishioka 1325

Insulation and Magnetic Properties of Iron Powder Coated by Wet Chemical MethodH.R. Cha, H.T. Son, C.H. Yun, J.I. Cho, I.H. Oh, J.S. Lee, C.S. Kang and H.M. Kim 1329

Iron-Based P/M Soft Magnetic Material for Electric Devices Operating at High FrequenciesT. Ishimine, T. Maeda, H. Toyoda, K. Mimura, T. Nishioka and S. Sugimoto 1333

Low-Temperature Sintering of Mn-Zn Ferrites Using a Media Agitation MillS. Handa, Y. Ohshima and Y. Nakasato 1337

Magnetic Properties and Microstructure of Sm2Co17-Based High Temperature PermanentMagnetJ.H. Yi, L.Y. Li and Y.D. Peng 1341

Magnetic Properties of Amorphous FeSiB and Nanocrystalline Fe73Si16B7Nb3Cu1 SoftMagnetic SheetsH.J. Cho, E.K. Cho, Y.S. Song, S.K. Kwon, K.Y. Sohn and W.W. Park 1345

Microstructure and Magnetic Properties of Nd2Fe14B/α-Fe Nanocomposite Prepared byHDDR Combined with Mechanical MillingL.X. Hu, E. Wang, B. Guo and G. Shi 1349

Magnetic Properties Obtained for Fe-50Co Alloy Produced by MIM with ElementalPowdersA. Silva, P.A.P. Wendhausen, R. Machado and W. Ristow 1353

Polyamine Group Assembled Silica Coated Ferrite Nanoparticle or Lambda DNA DetectionM.E. Park and J.H. Chang 1357

Materials Science Forum Vols. 534-536 o

Properties of Soft Magnetic Composite with Evaporated MgO Insulation Coating for LowIron LossG. Uozumi, M. Watanabe, R. Nakayama, K. Igarashi and K. Morimoto 1361

Sm2Fe17 Prepared by Calciothermic Reduction-Diffusion Using Different Iron PowdersJ.C. Boareto, J. Soyama, M.D.V. Felisberto, R. Hesse, A.V.A. Pinto, T.R. Taylor and P.A.P.Wendhausen 1365

Test Results of SMC Cores as Some Types of Motor CoresK. Asaka, C. Ishihara, Y. Enomoto and M. Ito 1369

C-10. Nano & Ultra-Fine Grained MaterialsCold and Detonation Spraying of TiB2-Cu NanocompositesO.I. Lomovsky, D.V. Dudina, V.Y. Ulianitsky, S.B. Zlobin, V.F. Kosarev, S.V. Klinkov, M.A.Korchagin, D.H. Kwon, J.S. Kim and Y.S. Kwon 1373

Dispersion of Alloy 625 Nanoparticles in EthanolE.H. Lee, M.K. Lee and C.K. Rhee 1377

Effect of Working Temperature on Microstructure and Mechanical Properties of UltrafineGrained Al and Al-5vol.%SiCp Composite Processed by Accumulative Roll-BondingS.H. Lee, S.Y. Chang and S.T. Oh 1381

Fabricating Devices Using Nano-Particulates with Direct Write TechnologyJ. Sears, J. Colvin and M. Carter 1385

Fabrication of Nanostructured Fe-Co Alloy Powders by Hydrogen Reduction and ItsMagnetic PropertiesY.J. Lee, B.H. Lee, G.S. Kim, K.H. Lee and Y.D. Kim 1389

Gd2O3:Eu System: Structural Study of the Influence of Luminescence CenterConcentrationM.E. Rabanal, L. Gómez, A. Khalifa, L. Mancic, O. Milosevic and J.M. Torralba 1393

Metal Plasma Source Ion Implantation Using a Pulsed Cathodic ArcS.Y. Chun 1397

Microstructure and Mechanical Properties of Nanostructured Aluminum Consolidated bySPSM. Zadra, F. Casari and A. Molinari 1401

Powder Metallurgy of Nanostructured High Strength MaterialsJ. Eckert, S. Scudino, P. Yu and C. Duhamel 1405

Preparation and Sintering of Nano-Sized W-Ni-Fe Powder by Sol-Spray-Drying ProcessJ.L. Fan, T. Liu, Y.Z. Ma and H.C. Cheng 1409

Properties of TiAl and TiAlN Thin Films by Pulsed Cathodic ARCS.Y. Chun, C.H. Lee and S.J. Lee 1413

Sintering of Mechanically Alloyed YSZ Nanocrystalline PowdersM.A. López de la Torre, O.J. Durá, M. Hernández, M. García Cordobés, G. Herranz, C. SánchezBautista and G.P. Rodríguez 1417

Structure Peculiarities of Nanocomposite Powder Fe40Al/Al2O3 Produced by MASHST. Talaka, T.F. Grigorieva, P. Vitiaz, N. Lyakhov, A. Letsko and A. Barinova 1421

Thermoelectric Properties of Nanostructured CoSb3 Synthesized by Mechanical AlloyingS.C. Ur, J.C. Kwon, M.K. Choi, S.Y. Kweon, T.W. Hong, I.H. Kim and Y.G. Lee 1425

C-11. PM Materials for Electrical and Electronic ApplicationsAmorphous Diamond for Generating Cold Cathode Fluorescence LightJ.C. Sung, M.C. Kan and S.C. Hu 1429

Development of Conductive and Anticorrosive Paint Dispersed with Carbon Particles forMetal Separators of PEFCM. Okahara, Z. Ishijima and M. Shirahige 1433

Development of High Performance Multi-Lobe Fluid Dynamic Bearings Using a SinteredMaterialH. Tokushima 1437

Displacement Properties of Newly Developed 3-Dimensional Piezoelectric Actuator atVarious AC FrequenciesM.S. Yoon, Y.G. Choi and S.C. Ur 1441

p Progress in Powder Metallurgy

Electroless Coating Process of Carbon Nano Fibers by Copper MetalJ.F. Silvain, P. Richard, J. Douin, M. Lahaye and J.M. Heintz 1445

Electromagnetic Properties of Silver Coated Iron Based Alloy Powders Prepared byChemical Reduction MethodB.Y. Lee, J.W. Lee, Y.C. Yun, I.B. Jeong and J.H. Moon 1449

Electrophoretic Deposition of Ni Nano-Particles for Self-Repairing of Heat ExchangerTubesG.J. Lee, S.I. Pyun and C.K. Rhee 1453

Glass Infilteration in Bonding of BaTiO3 and Al2O3 LayersH.S. Shin, J.H. Wang and J.H. Kim 1457

Interfacial and Surface Characterization of Fluorine Treated SnAgCu and NiTi Powdersand NiTi/SnAgCu Composite MaterialsJ.F. Silvain, C. Binot, E. Durand and A. Demourgues 1461

Microwave Absorbing Properties of Flaky Fe-Si-Al Alloy Powder-Rubber CompositesK.S. Lee, Y.C. Yun, I.B. Jeong and S.S. Kim 1465

Non-Electrolytic Deposition of Silver on Tungsten Powders for Functionally GradientComposite PowderJ.H. Lee and G.H. Chang 1469

Oxidation State of Manganese in LiMn2O4 Powders and Its Effect on ElectrochemicalPropertiesS.H. Kim, K.J. Lee, K.B. Shim and C.S. Kim 1473

Phase Transformation Behavior of Bi2O3-ZnO-Nb2O5 Ceramics Sintered at LowTemperatureF.T. Shiao, H.C. Ke and Y.C. Lee 1477

Photocatalytic Performance of Barium-Doped Strontium TantalateA. Kozu, H. Fujimori, K.Y. Kim, K. Oshiro, S. Yamamoto, Y. Sakata and H. Imamura 1481

Preparation of Ru-C Nano-Composite Film by MOCVD and Electrode Properties forOxygen Gas SensorT. Kimura and T. Goto 1485

Production of Dispersion-Strengthened Cu-TiB2 Alloys by Ball-Milling and Spark-PlasmaSinteringD.H. Kwon, J.W. Kum, T.D. Nguyen, D.V. Dudina, P.P. Choi, J.S. Kim and Y.S. Kwon 1489

P-Type and N-Type Bi2Te3/PbTe Functional Gradient Materials for Thermoelectric PowerGenerationK.Y. Lee and T.S. Oh 1493

Shrinkage Free Sintering of Low Temperature Cofired Ceramics by Glass InfilterationD.H. Yeo, J.H. You, H.S. Shin and J.H. Kim 1497

Sintering of High K LTCC Compatible DielectricsS. Duguey, R. Lebourgeois and J.M. Heintz 1501

Structural and Thermal Properties of Hot Pressed Cu/C Matrix Composites Materials Usedfor the Thermal Management of High Power Electronic DevicesP.M. Geffroy and J.F. Silvain 1505

The Characteristics of Sulfur Electrode with Carbon NanotubeH.S. Ryu, S.W. Lee, K.W. Kim, J.H. Ahn, K.K. Cho, G.B. Cho and H.J. Ahn 1509

The Influence of Production Process Parameters on the Properties W-Ag, Mo-AgCompositesJ. Leżański and M. Madej 1513

Thermal Stability and Properties of Cu-TiB2 Nanocomposites Prepared by CombustionSynthesis and Spark-Plasma SinteringD.H. Kwon, T.D. Nguyen, D.V. Dudina, J.W. Kum, P.P. Choi, J.S. Kim and Y.S. Kwon 1517

C-12. Functionally Graded MaterialsDevelopment of the High Performance Thermoelectric Modules for High Temperature HeatSourcesT. Jinushi, M. Okahara, Z. Ishijima, H. Shikata and M. Kambe 1521

Effect of Li2O Addition on Piezoelectric Properties of NKN-5LT CeramicsM.S. Kim, D.S. Lee, E.C. Park, S.J. Jeong, I.S. Kim and J.S. Song 1525

Elaboration of (Steel/Cemented Carbide) Multimaterial by Powder MetallurgyC. Pascal, J.M. Chaix, A. Dutt, S. Lay and C.H. Allibert 1529

Materials Science Forum Vols. 534-536 q

Graded Powder Composites by Freeze Drying, Electrophoretic Deposition and SinteringE. Olevsky and X. Wang 1533

Hard, Wear Resistant Metal Surfaces for Industrial Applications through Laser PowderDepositionJ. Sears and A. Costello 1537

Microstructure and Sintering Behavior of ZnO Thermoelectric Materials Prepared by thePulse-Current-Sintering MethodN. Shikatani, T. Misawa, Y. Ohtsu, H. Fujita, Y. Kawakami and T. Enjoji 1541

NiAl Behavior at Plasma Spray DepositionR.L. Orban, M. Lucaci, M. Rosso and M.A. Grande 1545

The Effect of Hot Extrusion on the Structure and Thermoelectric Properties of Bi2Te3MaterialX.Q. Liu, W. Ren, W. Han and X.L. Wang 1549

Thermoelectric Material Design in Pseudo Binary Systems of Mg2Si – Mg2Ge – Mg2Sn onthe Powder Metallurgy RouteT. Aizawa, R.B. Song and A. Yamamoto 1553

Thermoelectric Properties of Fe-Doped CoSb3 Prepared by Encapsulated Induction Meltingand Hot PressingK.H. Park, J.I. Lee, S.C. Ur and I.H. Kim 1557

Thermoelectric Properties of Ni-Doped CoSb3 Prepared by Encapsulated Induction Meltingand Hot PressingM.J. Kim, J.I. Lee, S.C. Ur and I.H. Kim 1561

Thermomechanical Properties of Functionally Graded Al-SiCp CompositesD.H. Song, Y.H. Park, Y.H. Park, I.M. Park and K.M. Cho 1565

Tungsten/Copper Functionally Graded Materials: Possible Applications and Processingthrough the Powder Metallurgy RouteO. Ozer, J.M. Missiaen, C. Pascal, S. Lay, J.M. Chaix and R. Mitteau 1569

Wear Resistance Properties of Tungsten Carbide/Stainless Steel Composite MaterialsPrepared by Pulsed Current SinteringY. Kawakami, F. Tamai, T. Enjoji, K. Takashima and M. Otsu 1573

C-13. PM Materials for Aerospace ApplicationsHigh Temperature Microstructural Stability of Si3N4 in TiAl AlloysJ.H. Choi and D.B. Lee 1577

Ni3Al-Fe-Cr Alloy Processed by Combined Mechanical Alloying - Reactive SynthesisR.L. Orban and M. Lucaci 1581

Preparation, Structure, and Properties of Ni3Al and NiAl Light Powder Alloys forAerospaceK.B. Povarova and O.A. Skachkov 1585

Structure and Properties of MASHS Titanium Aluminide–Based Powder Alloyed withChromiumT. Talaka, A. Ilyuschenko, A. Letsko and T. Hasak 1589

C-14. Superconducting MaterialEffect of Processing Factors on Critical Current Density in Bi2212/Ag WiresS.C. Kim, D.W. Ha, S.S. Oh, I.Y. Han, H.S. Ha and H.S. Sohn 1593

Fabrication of Bi-2212/SrSO4 Composite Superconductors by Melting Powder MixturesK.T. Kim, S.H. Jang, J.H. Lim, E.C. Park, J.H. Joo, H.J. Lee, G.W. Hong, C.J. Kim, H.R. Kimand O.B. Hyun 1597

Fabrication of TFA-MOD YBCO Films Using the Y2Ba1Cu1Ox and Ba3Cu5O8 PowdersJ.H. Lim, S.H. Jang, K.M. Yoon, S.Y. Lee, J.H. Joo, H.J. Lee and C.J. Kim 1601

Texture Evolution in Ni Substrate Prepared by Powder Metallurgy and Casting MethodsJ.H. Lim, K.T. Kim, E.C. Park, J.H. Joo, H.S. Kim, H.J. Lee, S.B. Jung and W.S. Nah 1605

The Effect of Deformation Stress-Strain and Temperature on The Ic Degradation of Bi-2223/Ag TapesH.S. Ha, S.C. Kim, D.W. Ha, S.S. Oh and J.H. Joo 1609

r Progress in Powder Metallurgy

D-01. Test and EvaluationDifference in Filling Property between Two Types of Binder Treated Powders Made ofAtomized or Reduced Iron PowderS. Uenosono and Y. Ozaki 1613

D-02. PM Production EquipmentsBiocompatibility and Mechanical Performance of Ni-TiJ. Kim, Y.C. Choi, H.S. Kim and S.I. Hong 1617

Prediction of Packing Density of Milled Powder Based on Packing Simulation and ParticleShape AnalysisY. Amano, T. Itoh, H. Terao and N. Kanetake 1621

D-03. Prospects of PM Research & IndustryRecent Advances in Dry-Bag Cip EquipmentY. Kishi, Y. Miyashita, Y. Manabe and T. Fujikawa 1625