Tabelle Taglio MAX200macc
-
Upload
balan-danut -
Category
Documents
-
view
230 -
download
0
Transcript of Tabelle Taglio MAX200macc
-
8/12/2019 Tabelle Taglio MAX200macc
1/21
OPERATION
CUT CHARTS
The following Cut Charts provide the necessary information in order for the operatorusing the MAX200 machine torch system to be successful in plasma arc cutting. TheCut Charts are divided into two areas: (1) above water cutting (pages 4-11 through 4-33) and (2) under water cutting, where the water table water is 3" above the topsurface of the workpiece (pages 4-34 through 4-45).
The following table provides the operator with a quick reference of the consumablesused for all cutting and gouging applications with the MAX200 machine torch. Alsolisted are the consumables used with the water-muffler.
Electrode
220021120547220021220021
220021120547
020415020415020415
020415
Nozzle
020608020611020689020615
020605020616
020608020611020615
020608
Shield
020424020448020688020485
020424020448
020602020448020485
020424
RetainingCap
120837120837120837120837
120837120837
120837
120837120837
120837
Plasma Gas/Shield Gas
Air/Air
O2 /Air
H35/N 2
N2 /CO 2
Swirl Ring
020607020607020613020607
020604020617
020607020607020607
020607
Part Numbers
MAX200 Machine Torch Consumables
Nozzle Type(Amps)
20010040
200 gouging
200100
200100
200 gouging
200
-
8/12/2019 Tabelle Taglio MAX200macc
2/21
2 2
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
60 1/8
1/81/81/8
3/161/41/41/41/4
5/165/16
3
333445666688
200 130
130135135140145150155160165170180185
200
135115100
80604530251510
75
5080
340029002540203015201140
760635380250180130
0.50.51.02.02.02.52.52.5
(66 SCFH) (270 SCFH)
020446Drag shield
020424Shield
020608Nozzle
120837Retaining cap
220021Electrode
020607Swirl ring
Air 44-48 / 58-62
6810131520
2532
50
MAX200 Machine Torch - Above Water
4 - 1 1
Mild Steel200 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical. Somesurface nitriting can occur.
Air3/16
1/43/81/25/83/47/8
11-1/41-1/21-3/4
2
90 90
Production cutting above 1 inch (25 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
3/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/83/16
1/43/81/25/83/4
120125125130135140145150
185175125
50352520
60504700445031751270
890635510
2356
10121520
ArcCurrentSetting(amps)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
0.50.50.51.0
020448Shield
120837Retaining cap
MAX200 Machine Torch - Above Water
(37 SCFH) (270 SCFH)6060 90
100 80 9022-26 / 48-52
22-26 / 54-58AirAir
020607Swirl ring
020611Nozzle
120547Electrode
4 - 1 2
Mild Steel
100 amps Air Plasma / Air ShieldThis gas combination gives good cut speed, low dross level and is very economical. Somesurface nitriting can occur. While this process may be used on thicker materials, optimalrecommended range is to 3/8 inch (10 mm).
2.52.5333345
3/323/32
1/81/81/81/8
3/16
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
4/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
60(25 SCFH) (275 SCFH)
Air 16-20 / 56-60
Mild Steel40 amps Air Plasma / Air Shield
This gas combination gives good cut speeds, low dross levels and is very economical. Somesurface nitriting can occur.
MAX200 Machine Torch - Above Water
020514Shield
120837Retaining cap
020689Nozzle
020613Swirl ring
220021Electrode
4 - 1 3
.0501/16.075
1/8.158.197
1/43/8
(18 GA.)
23456
10
Air 403/323/323/323/323/323/323/323/32
2.52.52.52.52.52.52.52.5
320300
220140120
503520
110110110110115115120125
810076005600355030501250
850500
0.5
90 90
Production cutting above 1/8 inch (3 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
5/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/4
3/81/25/83/47/8
11-1/41-1/21-3/4
2
68
10121520
2532
50
1/81/81/8
3/161/41/41/41/4
5/165/16
333445666688
120125125125130135135140150155165170
160120100
8070554535221510
7
4060300025402030178014001140
890560380250180
0.50.51.02.02.02.52.52.5
120 90200(72 SCFH) (270 SCFH)
Air 60 O 2 48-52 / 64-68
Mild Steel200 amps O 2 Plasma / Air Shield
This gas combination gives superior cut speed, minimum dross, minimum amount of surfacenitriting and excellent weldability.
MAX200 Machine Torch - Above Water
220021Electrode
020604Swirl ring
020605Nozzle
120837Retaining cap
020424Shield
4
- 1 4
Production cutting above 1 inch (25 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
6/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
ArcCurrentSetting(amps)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Mild Steel 100 amps O 2 Plasma / Air Shield
This gas combination gives good cut speed, low dross level and is very economical. Somesurface nitriting can occur. While this process may be used on thicker materials, optimalrecommended range is to 3/8 inch (10 mm).
MAX200 Machine Torch - Above Water
(40 SCFH) (270 SCFH)
6012-16 / 52-56 AirO 2
4 - 1 5
1/83/16
1/43/81/25/83/4
356
10121520
3/321/81/81/81/8
3/16
105110110115115125130
240180110
70504030
610045503050178012701020
760
0.50.5
120 90100
020448Shield
120837Retaining cap
020616Nozzle
120547Electrode
020617Swirl ring
2.5333345
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
7/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
3333456666
33002800216014001140
635510380250130
1/81/81/81/8
3/161/41/41/41/4
56
10121520
2532
3/161/43/81/25/83/47/8
11-1/41-1/2
130110
85554525201510
5
0.51.01.52.02.02.53.03.0
120125130130135145150160165175
200 120 90
020446Drag shield 120837
Retaining cap020608Nozzle
020607Swirl ring
020415Electrode
CO 2 60(60 SCFH) (210 SCFH)
N2 36-40 / 52-56
Mild Steel200 amps N 2 Plasma / CO 2 Shield
This gas combination is used when cut edge quality and surface nitriting are less important.Electrode life is extended when this combination is used.
MAX200 Machine Torch - Above Water
020424Shield
4
- 1 6
Production cutting above 1 inch (25 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
8/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
3/161/43/81/25/83/47/8
11-1/41-1/2
56
10121520
2532
1/81/81/81/8
3/16 1/4 1/41/41/4
3333456666
200 125130130135140140145
150160170
220195145105
755540
301510
5600500037002700190014001000 760380250
0.51.02.02.02.53.0
90 90
020446Drag shield
020424Shield
120837Retaining cap
020608Nozzle
020607Swirl ring
220021Electrode
Air 60(66 SCFH) (270 SCFH)
Air 44-48 / 58-62
Stainless Steel200 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical. Somesurface nitriting and surface oxidation of alloying elements can occur.
MAX200 Machine Torch - Above Water
4 - 1 7
Production cutting above 7/8 inch (21 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
9/21
ArcCurrentSetting(amps)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcVoltageSetting(volts)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/83/16
1/43/81/25/83/4
356
10121520
125130130135140145150
100 140110
8055352520
3560280020301400
890635510
0.50.50.5
90 90Air 60(37 SCFH) (270 SCFH)
Air 22-26 / 54-58
120547Electrode
020607Swirl ring
020611Nozzle
020448Shield
120837Retaining cap
MAX200 Machine Torch - Above Water
4 - 1 8
Stainless Steel100 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical. Somesurface nitriting and surface oxidation of alloying elements can occur.
2.5333345
3/321/81/81/81/8
3/16
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
10/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
40 90
(25 SCFH) (275 SCFH)
Stainless Steel40 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical. Somesurface nitriting and surface oxidation of alloying elements can occur.
MAX200 Machine Torch - Above Water
Air Air 16-20 / 56-60 60
020514Shield
120837Retaining cap
020689Nozzle
020613Swirl ring
220021Electrode
4 - 1 9
.0501/16
1/81/43/8
(18 GA.)
36
10
3/323/323/32
1/81/8
120120125135140
0.5
145120
753012
902.52.52.533
370030501900
750300
Production cutting above 1/8 inch (3 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
11/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
3/161/4
3/81/25/83/47/8
11-1/41-1/2
56
10121520
2532
1/81/8
1/81/8
3/161/41/41/41/4
33
33456666
200 125130
130135140140145150160160
135120
10075604535201510
34303050
2540190015201140
890510380250
0.51.02.02.02.52.5
120 90
020424
Shield
020608Nozzle
120837Retaining cap
020415Electrode
020607Swirl ring
60(60 SCFH) (270 SCFH)
N2 34-38 / 50-54
Stainless Steel200 amps N 2 Plasma / Air Shield
This gas combination is used when cut edge quality, surface nitriting and surface oxidation ofalloying elements are less important. Electrode life is extended when this combination isused.
Air
MAX200 Machine Torch - Above Water
4 - 2 0
Production cutting above 7/8 inch (20 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
12/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
3/161/43/81/25/83/47/8
11-1/41-1/2
1/81/81/81/8
3/16 1/4 1/41/41/4
3333456666
200 125130130135140140145
150160170
190170125
95705040
301510
4800430032002400180012501000 760380250
0.51.01.52.02.02.53.0
120 90
020424Shield
020608Nozzle
120837Retaining cap
020415Electrode
020607Swirl ring
CO 2 60(60 SCFH) (210 SCFH)
N2 36-40 / 52-56
MAX200 Machine Torch - Above Water
56
10121520
2532
Stainless Steel200 amps N 2 Plasma / CO 2 Shield
This gas combination is used when surface nitriting and surface oxidation of alloying ele-ments is less important. Electrode life is extended when using this gas combination.
4 - 2 1
Production cutting above 7/8 inch (20 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
13/21
MAX200 Machine Torch - Above Water
020608Nozzle
120837Retaining cap
020415Electrode
020607Swirl ring
020602Shield
WARNING
Do not use water muffler
when cutting with argon-hydrogen!
Stainless Steel200 amps H35 Plasma / N 2 Shield
This gas combination (Hypertherm recommends a mixture of 35% hydrogen and 65% argon for the plasma gas)gives maximum thickness cutting capability, minimum dross levels, minimum amount of surface contamination,excellent weldability and excellent cut quality on thicknesses greater than 1/2". On thicknesses less than 1/2 ",excessive dross levels may be experienced. Electrode life is extended when this combination is used.
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/43/81/25/83/47/8
11-1/41-1/21-3/4
2
610121520
2532
135140140145150155155165170180185
625242373227221611
86
160013001100
940810690560400280200150
N2 60(70 SCFH) (275 SCFH)
H35 36-40 / 62-66 200 1.01.02.02.02.52.5
4 - 2 2
90120
Note: Maximum piercing thickness 3/4" (20mm) and IHS recommended.
Torch-to-work Distance(Inches) (mm)
3/163/16
3/161/41/4
5/16 5/165/165/165/165/16
55
566888888
Production cutting above 7/8 inch (20 mm) not recommended.
* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
14/21
ArcCurrentSetting(amps)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
ArcVoltageSetting(volts)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/83/16
1/43/81/2
356
1013
130135140140145
100 12601060
890750630
0.50.50.5
N2(20 SCFH) (270 SCFH)
H35 32-36/ 56-60
Stainless Steel100 amps H35 Plasma / N 2 Shield
This gas combination gives good cut speed, but may result in severe dross. Some surfacenitriting and surface oxidation of alloying elements can occur.
MAX200 Machine Torch - Above Water
60 5040353025
120 90
Note: Maximum piercing thickness 3/8-inch (10 mm) and IHS recommended.
4 - 2 3
020415Electrode
020607Swirl ring
020611Nozzle
020448Shield
120837Retaining cap
WARNING
Do not use water mufflerwhen cutting with argon-hydrogen!
Torch-to-work Distance(Inches) (mm)
3/321/81/81/81/8
2.53333
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
15/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
2003/161/43/81/25/83/47/8
11-1/41-1/2
56
10121520
2532
1/81/81/81/8
3/16 1/4 1/41/41/4
3333456666
130140140145150155160
165170175
220190145110
8565
50352012
5600480037002800220016501300 900500300
0.51.02.02.52.52.52.5
90 90
020446Drag shield
020424Shield
120837Retaining cap
020608Nozzle
020607Swirl ring
220021Electrode
Air 60(66 SCFH) (270 SCFH)
Air 44-48 / 58-62
Aluminum200 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical.
MAX200 Machine Torch - Above Water
4 - 2 4
Production cutting above 7/8 inch (21 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
16/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/83/16
1/43/81/25/83/4
356
10121520
135140145145150155160
0.50.50.5
100 110907050403025
28002290178012701010
760635
9090Air 60(270 SCFH)
Air 22-26 / 54-58(37 SCFH)
3/321/81/81/81/8
3/16
2.5333345
120547Electrode
020607Swirl ring
020611Nozzle
020448Shield
120837Retaining cap
Aluminum100 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical.
MAX200 Machine Torch - Above Water
4 - 2 5
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
17/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
90Air 60(25 SCFH) (275 SCFH)
Air 16-20 / 56-60
Aluminum 40 amps Air Plasma / Air Shield
This gas combination gives good cut speed, low dross levels and is very economical.
MAX200 Machine Torch - Above Water
020514Shield
120837Retaining cap
020689Nozzle
020613Swirl ring
220021Electrode
4 - 2 6
3/321/81/43/8
3/323/32
1/81/8
2.52.533
120130140150
35502550
900350
0.536
10
140100
3515
40 90
Production cutting above 1/8 inch (3 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
18/21
3333456666
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
200 120 90457040603050203017801270
890 635510250
1/81/81/81/8
3/16 1/4 1/41/41/4
3/161/43/81/25/83/47/8
11-1/41-1/2
180160120
80705035
252010
0.51.01.52.02.02.52.5
130135135140140150160
165175185
56
10121520
2532
020446Drag shield
020424Shield
120837Retaining cap
020608Nozzle
020607Swirl ring
020415Electrode
60(60 SCFH) (270 SCFH)
N2 34-38 / 54-54
MAX200 Machine Torch - Above Water
Air
4 - 2 7
Aluminum200 amps N 2 Plasma / Air Shield
This gas combination is used when cut edge quality is less important. Electrode life is ex-tended when this combination is used.
Production cutting above 7/8 inch (20 mm) not recommended.
* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
19/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
200 903/161/43/81/25/83/47/8
11-1/41-1/2
56
10121520
2532
1/81/81/81/8
3/16 1/4 1/41/4
5/16
3333456668
130135135140140150160
165175185
185160120
95705542
332011
4700405030502400180014001050 840510280
0.51.02.02.52.53.03.0
120
020446Drag shield
020424Shield
120837Retaining cap
020608Nozzle
020607Swirl ring
020415Electrode
60(60 SCFH) (210 SCFH)
N2 36-40 / 52-56
Aluminum200 amps N 2 Plasma / CO 2 Shield
This gas combination is used when cut edge quality is less important. Electrode life is ex-tended when this combination is used.
MAX200 Machine Torch - Above Water
CO 2
4 - 2 8
Production cutting above 7/8 inch (20 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
20/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
3/161/43/81/25/83/47/8
11-1/41-1/21-3/4
2
3/163/16
1/41/41/4
5/16 5/165/165/165/165/165/16
556668888888
200 130130135140145150155155165170180185
170155120100
80605040261812
7
43004000300025502000150012501000
660460300180
0.51.02.02.02.52.52.5
120 90N2 60(70 SCFH) (275 SCFH)
H35 36-40 / 62-66
MAX200 Machine Torch - Above Water
610121520
2532
50
4 - 2 9
020446Drag shield 120837
Retaining cap020608Nozzle
020607Swirl ring
020415Electrode
020602Shield
Aluminum 200 amps H35 Plasma / N 2 Shield
This gas combination (Hypertherm recommends a mixture of 35% hydrogen and 65% argonfor the plasma gas) gives maximum thickness cutting capability, excellent cut quality andexcellent weldability. Electrode life is extended when this combination is used.
WARNING
Do not use water mufflerwhen cutting with argon-hydrogen!
Production cutting above 7/8 inch (20 mm) not recommended.
* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14
-
8/12/2019 Tabelle Taglio MAX200macc
21/21
Material Thickness(Inches) (mm)
ShieldGasType
ShieldGas
Pressure(psi)
Torch-to-work Distance(Inches) (mm)
ArcCurrentSetting(amps)
ArcVoltageSetting(volts)
Travel Speed(ipm) (mm/min)
Approx.Motion
Delay Time(sec)
PlasmaGas InletPressure
(psi)
ShieldGas InletPressure
(psi)
Plasma Gas Type
Plasma Gas PressureTEST/RUN (psi)
1/83/16
1/43/81/2
356
1012
135140145145150
0.50.50.5
100 9585806050
24402200198015301280
90120N2 60(270 SCFH)
H35 32-36 / 56-60(20 SCFH)
3/321/81/81/81/8
2.53333
Aluminum100 amps H35 Plasma / N 2 Shield
This gas combination gives good cut speed, low dross levels and is very economical.
MAX200 Machine Torch - Above Water
4 - 3 0
020415Electrode
020607Swirl ring
020611Nozzle
020448Shield
120837Retaining cap
WARNING
Do not use water mufflerwhen cutting with argon-hydrogen!
Production cutting above 3/8 inch (10 mm) not recommended.* If leads are greater than 50 feet, increase TEST pressure 5 psi for every extra 50 feet of torch lead length. 14