T-002 RoadMachine Manual2010

8/9/2019 T-002 RoadMachine Manual2010

1/8

5280 Main Street NE Minneapolis, MN 554211.877.226.7824 | www.kurtkinetic.com

ROAD MACHINE

ASSEMBLY MANUMODEL


2/8www.kurtkinetic.com | 1.877.226.7824

Page 2

COMPONEN

Part A

FoldingFrame

Tools Required for Assembly: 14mm Wrench, 4mm Hex Key

When unpacking, check that the following components are present:

Part B

ResistanceUnit

ROLLER

FLYWHEEL

YOKE

Because wetest eachtrainer therewill be tiremarks on the

roller.

Your Kinetic Trainer is designed for use with road, mountain, BMX andrecumbent bikes. Before adjusting these legs, you must know yourbikes tire size, which is printed on the sidewall of every tire.

When shipped from the factory, the folding leg is mounted in Position

1 on the main frame and will function with all tire sizes. However, tolower the drive wheel and maintain good riding position it is best toadjust the leg position to match your tire size. Ideally, your rear tireshould be approximately 1-1/2 from the floor. Use the chart shownhere to determine the recommended leg position.

The appropriate leg position may vary for some wheel diametersbecause of tire thickness. Choose the setting that positions the bike aslevel as possible.

Part C

L-Bolt

Part F

MountingBolt andNut

Part N

Small ConeCup(Installed on trainer)

Part K

Small Cone CupSkewer Adapter(see www.kurtkinetic.com for installation instructions)

Part E

AdjustmentKnob andWasher

Part M

Skewer

Part D

Spring

ADJUSTABLE FOLDING LE

1

2

43

PLEASE NOTE:If any of the

componentslisted are

missing, pleasecall our CustomerService hotline at

877-226-7824.

SERIALNUMBER

Use two wrenches to remove the nut.Remove bolt. Select appropriate hole

and reinsert bolt through frame and leg.Attach nut and tighten securely until

some resistance is felt in the movementof the folding leg. Repeat with other side.

FRAMEPOSITION position 1 position 2 position 3 position 4

MAXIMUNTIRE SIZE 700c / 29 650c 24 20



Pag

QUICKRELEASELEVER

LOCK RING

RISER RING

LEG BOLT

ADJUSTMENT KNOB

FLYWHEEL

RESISTANCE UNIT

TRAINER DETAI

TENSIONINGKNOB



Page 4

1

2

ATTACH RESISTANCE UN

PART F

PART C

Fasten resistance

unit with mountingbolt and nut

Place L-Bolt in framesleeve as shown



Pag

3

4

ATTACH RESISTANCE UN

PART D

PART E

Slide spring over

L-Bolt

Tilt the resistanceunit up towardthe frame whiledirecting L-bolt intothe hole in the yoke.Attach adjustmentknob and washer.



Page 6

MOUNTING BI

1

2

Loosen lockring andTurn knob tocenter bike

QUICKRELEASE

Push knobtight againstskewer, closequick releaseand tighten

knob until tireis centeredon roller

3

Tighten knob onquick release side

of trainer until wheelis firmly centered

on resistance unitroller

RIGHT SIDE

Grip frameat seat stay

At this point,be sure thatresistanceunit is looselytightened anddoes not touchtire.



Pag

MOUNTING BI

5

4

Tighten lockring when wheelis centered onresistance unit andbike is firmly lockedin at the skewer

Turn adjustmentknob until rollertouches tire. thenadd 2 to 5 moreturns.

test tire friction bysharply moving

tire a 1/4 turn backand forth. apply

another 1/2 turn onadjustment knob if

needed.

KINETIC SKEWER(included with trainer)

*FOR YOUR SAFETYWe recommend using the skewer that was included with your trainer.

RECOMMENDED SKEWER AND CONE COMBINATION*

PART M

PART N

BIKE REMOV

To properly remove the bike:

1. Turn the adjustment knobon the resistance unitcounterclockwise to back theroller away from the tire until itis no longer touches.

2. Reduce axle tension byturning the right axle knobcounterclockwise, a minimumof two turns, to allow fordisengagement of the quickrelease.

3. Firmly grasp your bike seat tostabilize the bike.

4. Disengage the quick releaseon the right side of the trainerand slide the axle knob to thefully open position. The bikecan now be removed from theleft cone cup.

LEFT SIDE


8/8

5280 Main Street NE Minneapolis, MN 554211.877.226.7824 | www.kurtkinetic.com

WARRAN

CRASH REPLACEMENT POLICAUTION

CARING FOR YOUR TRAINER

Do not over-tighten the adjustment knob (Part E). Over-

tightening will cause both tire and unit damage. Tighten only

enough to avoid tire slippage.

When using the trainer for normal use or for extended periodsof time, the resistance unit will get hot. DO NOT touch theresistance unit while it is in use or while it is hot.

Always consult a doctor before beginning any exercise routineor using any exercise or fitness product including the KineticTrainer. Should you become ill, feel dizzy, light-headed ornauseous while riding the trainer, stop riding immediately and

seek medical attention.

While in use, the wheel of your bike and the resistanceunit may be spinning at high speeds. For this reason keepchildren, pets and all items safely away from your trainerwhile in use. Also be sure that your bike is correctly installedand securely locked into the trainer before riding.

Always use the trainer on a flat surface.

In order to keep from tipping the trainer over, be careful not to

lean too far side to side on the Rock and Roll trainer.

By purchasing the Kinetic Trainer youve made an investment in a top-quality piece ofequipment. When used according to the manufacturers instructions and cared for with

common sense, your Kinetic trainer will provide a lifetime of training. Store the trainerindoors, out of the rain and away from temperature extremes. Since sweat is corrosive,you can extend the life of your trainer by wiping it off after your workout.

Kinetic by Kurt offers the original owner a lifetime warranty againstmanufacturing defects and/or normal wear and tear for both the trainer frameand the resistance unit. This warranty is not applicable to damage caused bymisuse, abuse, neglect, accident or unauthorized modification of materials orparts. If the unit is disassembled by the consumer, this warranty is void. Thereare no other warranties, expressed or implied.

It is the responsibility of the purchaser to file a warranty card via mailor on-line with Kinetic in the event that repairs are needed. It is also the

responsibility of the purchaser to retain receipts for proof of purchase in theevent that repairs are needed. No warranty repairs will be accepted withoutthe warranty registration and the serial number of the trainer located on theresistance unit.

WARRANTY CARD/PRODUCT REGISTRATION

Please complete the warranty card with the information requested and returnit to Kinetic within 30 days of purchase. You can also go to www.kurtkinetic.com and fill out the warranty information online.

WARRANTY CLAIMS/REPLACEMENT PARTS

If you experience problems with your trainer, please call our Customer ServiceHotline at 877-226-7824 or email us at [email protected] . To help ushandle your call as efficiently as possible, please have your trainers serialnumber ready to give to the customer service representative.

After determining what repairs or replacement parts may be needed, you willbe provided with a Return Material Authorization Number and procedures for

returning your product to Kinetic.

In some cases replacement parts may be shipped directly to you, dependingon the nature of the problem. No product returns will be accepted without aReturn Material Authorization Number.

Kinetic trainers come with a lifetime warranty on the frame and the resistanceunit to the original owner.

However, we understand that accidents can happen involving our products,so we also offer a crash replacement policy for incidents not covered by ourlifetime warranty. Here is how it works: Kinetic will replace any part or partson your Kinetic Trainer that are damaged due to an accident, regardless of thecause of that accident, and within reason for a $50.00 cost plus the cost of

parts and shipping charges.

We reserve the right to reject any product that has been so severelydamaged that it cannot be rebuilt. To be eligible, you must complete thewarranty registration process by mail or online. Crash replacement repairs

require warranty information and the serial number of your unit. This crashreplacement policy and its related charge may be subject to change withoutnotice.

To process a claim, please call our Customer Service Hotline at 877-226-7824or email us at [email protected]. You will be provided a Return MaterialAuthorization number and you will be given instructions for returning theproduct to us. In some cases replacement parts may be shipped to you. Noproduct returns will be accepted without an RMA number.

Record the Serial Number of Your Kinetic Trainer Here

T-002 RoadMachine Manual2010

Documents

Transcript of T-002 RoadMachine Manual2010