049900006 July 2014

®

SYSTEM FOR SLIDING DOORInstallation procedure

Features

• Realizedwithatelescopicguide,withhardenedtracksandsteelballsforbearing.

• Highreliabilityoftheslidingsystemduringtime.

• Reducedoveralldimensionsinsidethevehicle.

• Quickassemblyandeasyuse.

• Basedonadoorwithwidth900mm,maximumthickness85mm,maximumweight100kg.

• Forslidingdoorsfromrighttoleftandfromlefttoright

Picture1

®

1

Components of the kit

1 � N° 1 zinc plated plate

2 � N° 1 stainless steel lower rail

3 � N° 1 small limit stop plate

4 � N° 1 door block

5 � N° 1 stainless steel rail bar for the lower door

6 � N° 2 zinc plated linear guides

7 � N° 1 zinc plated telescopic guide L=900 mm

8 � N° 1 limit stop rubber

9 � N° 1 limit stop block

®

2

Assembly

Picture 2

The roof and the door must be properly reinforced with suitable plates where the fixing holes are located.

Assembly stages

®

3

1.FixingthetelescopicguideL900mm7onthedoorthroughcountersunkM5screws.

2.Fixingthelimitstopplate3onthedoorwithcountersunkM8screws(seepicture3).

3.Fixingthelimitstopblock9onthezincplatedplate1(seepicture4).

4. Fixingthesmalllimitstopplate3andthelimitstoprubber8onthezincplatedplate1throughacountersunkM5screw(seepicture3)

Picture 3 door completely opened

Picture 4 door completely open - detail of the limit stop block

®

4

Picture3doorcompletelyopened

Picture4doorcompletelyopen-detailofthelimitstopblock

5. Assembly of the zinc plated plate 1 to the telescopic guide 7 through countersunk M5 screws

Verifying the correct functioning of the system composed by the limit stop plate 3-limit stop rubber 8-door block 4

6. Fixing the rail bar of the lower door 5 onto the door through countersunk M8 screws

Picture 5 door completely open – detail on M6 screws on linear guides

5

®

7. Positioningofassembleddoorontothevehicletocheckthepositioningofthelinearguides.6

Itmustbeverifiedthatthelimitstopofthelinearguides 6 correspondstitheconfigurationofmaxcomingoutofthedoor.(picture5)

8. Fixing the linear guides 6 to the roof through countersunk M8 screws through a stop limit screw on the side of the door (picture 5)

9. Mounting the door on the vehicle through assembly of the zinc plated plate 1 to the linear guides 6 through M8 screws.

10. Fixing the stainless steel lower rail 2 on the external side of the body or the frame.

Verifying that the positioning of said stainless steel rail 2 is so that the door is maintained in vertical position and the limit stop is guaranteed when closing.

6

®

PASTORE & LOMBARDI S.p.A. con socio unico soggetta a direzione e coordinamento di HILBE S.p.A.

Via Don Minzoni, 340057 Cadriano di Granarolo Emilia (Bologna) - Italy

Capitale Sociale € 468.000 i.v. R.I. Bologna, C.F. e P.IVA 03276650375

R.E.A. della C.C.I.A.A. di Bologna 277528 Tel. +39 051 764111 - Fax +39 051 765414

info@pastorelombardi.comwww.pastorelombardi.com

®