swift - asaseletricas.com.br fileELEVATOR AILERON 20mm 20mm 25mm 25mm The CG position will vary...
1
ELEVATOR AILERON 20mm 20mm 25mm 25mm The CG position will vary depends on your requirement. Move the CG to achieve your control style. CG 80mm Vacoum servo cover M4 screw A B C. A Apply epoxy glue. Apply instant glue. (CA glue,super glue). Wing Span.......... 2500 mm Weight................ 1600 - 1800g Length................ 1400 mm Wing Area........... 22.5 dm Airfoil.................. Eppler 374 Radio................... 6 channel SPECIFICATIONS 2 3 1 1 Horns Linkage stopper 1.5×60mm Metal Rods Metal Rods 12×500mm Carbon rod 3 1.5×1200mm Metal Rods Fiberglass sheet hinge with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting.Increase the setting if necessary.If it is too high, you may damage the film. The pre-covered film on ARF kits may wrinkle due to variations of temperature.Smooth out as explained below. Retract gear w/2.25“ wheel 1 1 1 1 PA 2.5 x 10mm TP screw 3×50mm 5×30mm Wood Rod 4 4 6 5 SWIFT clevis 0.3×1200mm soft wire 1.5×1.0mm L10mm plywood clevis connector 2.0×1.5mm 3 Designed and Manufactured by FlyFly Hobby Mfg. [email protected] http://www.flyflyhobby.com Copyright 2006-2012 Fly Fly Hobby. All right reserved. A = A' B = B' A' A B B’ = C ' C If the tail is not right angle to the fin, apply tape to one side to achieve the right alignment. Warning! C C' A B Double-Side Tape A B PA 2.5 x 10mm TP screw
Transcript of swift - asaseletricas.com.br fileELEVATOR AILERON 20mm 20mm 25mm 25mm The CG position will vary...
ELEVATOR
AILERON
20mm20mm
25mm
25mm
The CG position will varydepends on your requirement.Move the CG to achieve yourcontrol style. CG
80mm
Vacoum servo cover
M4 screw
AB
C.A
Apply epoxy glue.
Apply instant glue.(CA glue,super glue).
Wing Span.......... 2500 mmWeight................ 1600 - 1800gLength................ 1400 mmWing Area........... 22.5 dmAirfoil.................. Eppler 374Radio................... 6 channel
SPECIFICATIONS
2
3
1
1
Horns
Linkage stopper
1.5×60mm Metal Rods
Metal Rods
12×500mm Carbon rod
3
1.5×1200mm Metal Rods
Fiberglass sheet hinge
with cover (cloth)low setting
Use an iron covered with a cloth! Startat low setting.Increase the setting ifnecessary.If it is too high, you may damage the film.
The pre-covered film on ARF kits may wrinkle due to variationsof temperature.Smooth out asexplained below.
Retract gear w/2.25“ wheel 1
1
1
1
PA 2.5 x 10mm TP screw
3×50mm
5×30mm Wood Rod
4
4
6
5
SWIFT
clevis
0.3×1200mm soft wire
1.5×1.0mm L10mm
plywood
clevis connector 2.0×1.5mm 3
Designed and Manufactured byFlyFly Hobby [email protected]://www.flyflyhobby.com
Copyright 2006-2012 Fly Fly Hobby. All right reserved.
A = A'B =B'
A'A
B B’
= C 'C
If the tail is not right angleto the fin, apply tape to oneside to achieve the right alignment.
Warning! C C'
AB
Double-Side Tape
AB
PA 2.5 x 10mm TP screw
