Sweet Paul Lantern How-To’s

STITCHED LANTERN

Tools & Materials:

• Templates • Cardstock • Printer • Light-weight craft paper • Pencil • Scissors • Sewing machine w/ thread • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Print out templates onto cardstock. On craft paper, trace the side panel six times and the bottom panel one time (or print directly onto the craft paper).

2. With scissors, cut out all pieces of the lantern. 3. Place two side panel pieces together and sew along the right edges, leaving a ¼”

seam allowance. Do this two more times with the remaining pairs of panels. 4. Using your fingers, carefully press each seam open and flat, to begin shaping the

sides of the lantern. 5. Sew the remaining edges together to make a 6-sided lantern and, again, carefully

press each seam open and flat. 6. For the bottom panel, fold up the tabs along the dotted lines. Apply glue to the

tabs and press into place on the inside edges of the bottom of the lantern. 7. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 8. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 9. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"1

Sweet Paul Lantern How-To’s

COLLAGE LANTERN

Tools & Materials:

• Templates • Cardstock • Printer • Light-weight craft paper • Pencil • Scissors • Sewing machine w/ thread • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Print out the templates onto cardstock. 2. On craft paper, trace each side panel two times, the bottom panel one time, and

the petal shapes as many times as desired (or print directly onto the craft paper). 3. With scissors, cut out all pieces of the lantern. 4. To decorate the side panels, create stacks of petal cut outs, lay as desired on side

panel piece, and, using a sewing machine, stitch the stack of petals into place. 5. Place two side panel pieces wrong sides together (sides with no petals sewn on)

and sew along the right edge, leaving a ¼” seam allowance. Do this one more time with the second pair of panels.

6. Using your fingers, carefully press each seam open and flat. 7. Sew the remaining edges together, again, leaving a ¼” seam allowance, to make a

4-sided lantern and, again, carefully press each seam open and flat. 8. For the bottom panel, fold up the tabs along the dotted lines. Apply glue to the

tabs and press into place on the inside edges of the bottom of the lantern. 9. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 10. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 11. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"2

Sweet Paul Lantern How-To’s

CUT OUT LANTERN

Tools & Materials:

• Templates • Cardstock • Printer • Light-weight craft paper • Pencil • Scissors • Sewing machine w/ thread • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Print out the templates onto cardstock. 2. On craft paper, trace the side panel four times, the bottom panel one time, and the

flower shapes as many times, in as many sizes as desired (or print directly onto the craft paper).

3. With scissors, cut out all pieces of the lantern. 4. To decorate the side panels, create graduated stacks of the flower cut outs, lay

stacks in a line along the center of each side panel of the lantern, and, using a sewing machine, stitch the stack of petals into place with a simple straight stitch.

5. Fold the petals upward around the stitch. 6. Place two side panel pieces, wrong sides together (side with no flowers sewn on)

and sew along the right edge, leaving a ¼” seam allowance. Do this one more time with the second pair of panels.

7. Using your fingers, carefully press each seam open and flat. 8. Sew the remaining edges together to make a 4-sided lantern and, again, carefully

press each seam open and flat. 9. For the bottom panel, fold up the tabs along the dotted lines. Apply glue to the

tabs and press into place on the inside edges of the bottom of the lantern. 10. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 11. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 12. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"3

Sweet Paul Lantern How-To’s

FOLDED LANTERN

Tools & Materials:

• Templates • Cardstock • Printer • 11 x 17 light-weight craft paper • Pencil • Scissors • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Print the lantern side panels template directly on to 11x17 paper. 2. Print the other templates onto cardstock and on craft paper, trace the bottom panel

one time and the triangle shape eight times, (or also print these directly onto the craft paper).

3. With scissors, cut out all pieces of the lantern. 4. For the side panels, fold inward along all of the dotted lines. Glue left side tab to

the opposite (right) side of the lantern to form a cuboid shape. 5. To fill in the gaps at the top and bottom of the lantern, use glue to attach each of

the eight triangle cut outs to the corresponding tabs. 6. For the bottom panel, fold up the tabs along the dotted lines. Apply glue to the

tabs and press into place on the inside edges of the bottom of the lantern. 7. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 8. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 9. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"4

Sweet Paul Lantern How-To’s

COLORED LANTERN

Tools & Materials:

• Templates • Cardstock • Printer • Light-weight craft paper • Pencil • Scissors • Sewing machine w/ thread • Liquid acrylic paint • Small paint brush • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Print out the templates onto cardstock. 2. On craft paper, trace the side panel five times and the bottom panel one time (or

print directly onto the craft paper). 3. With scissors, cut out all pieces of the lantern. 4. Place two side panel pieces together and sew along the right edge, leaving a ¼”

seam allowance. Do this one more time with another pair of panels. 5. Using your fingers, carefully press each seam open and flat. 6. Sew the pairs of panels and the remaining fifth single panel together to make a 5-

sided lantern and, again, carefully press each seam open and flat. 7. To decorate the lantern, use a small paintbrush saturated in liquid acrylic color to

paint along all of the sewn edges. Let dry completely. 8. For the bottom panel, fold up the tabs along the dotted lines. Apply glue to the

tabs and press into place on the inside edges of the bottom of the lantern. 9. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 10. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 11. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"5

Sweet Paul Lantern How-To’s

DYED LANTERN

Tools & Materials:

• Large piece light-weight craft paper • Scissors • Liquid acrylic paint • Water (optional) • Bowl • 11 x 17 paper • Sewing machine w/ thread • Quart container lid • Glue • Wire • Pin or needle • LED tea lights

How-To:

1. Loosely cut strips of craft paper 1 to 2 inches wide and 18 inches long. 2. Coil each piece up and, to dye, dip one edge of coil into a bowl of liquid acrylic

paint (thinned with water as desired). 3. Let paper coils dry completely before continuing. 4. Once dry, uncoil strips and lay lengthwise, in an overlapping pattern on a piece of

11 x 17 paper, covering the paper entirely. 5. Using a sewing machine, stitch as desired to hold the dyed strips of paper in

place. 6. Trim an inch off either end of the paper (to neaten the edges and to make the final

length 15 inches). 7. Wrap the sheet of paper around the outside of a quart container lid to get the

correct diameter for the cylinder. 8. Where the opposite edges overlap, secure in place with glue. 9. Once dry, apply glue to the edges of the quart container lid and insert into the

bottom of the cylinder. Let dry completely. 10. Twist a loop in the middle of a 24” piece of wire. Bend the length on each side

down like a handle and curl up the edges. 11. Using a pin or a needle, poke a hole on either side of the lantern, near the top

edge. 12. Thread the lantern on to the handle, place an LED tea light in the bottom, and

hang as desired.

"6

COLORED LANTERN:

BOTTOM PANEL

Cut along solid lines; fold along dotted lines.

CUT OUT LANTERN:

BOTTOM PANEL

Cut along solid lines; fold along dotted lines.

CUT OUT LANTERN:

FLOWER CUT OUTS

TOP

BOTTOM

CUT OUT LANTERN:

SIDE PANELS

Cut out 4.

FOLDED LANTERN: SIDE PANELS

Cut along solid lines; fold along dotted lines.

GLU

E TA

B

FOLDED LANTERN: TRIANGLES & BOTTOM PANEL

Cut along solid lines; fold along dotted lines.

STITCHED LANTERN: BOTTOM PANEL

Cut along solid lines; fold along dotted lines.

STITCHED LANTERN: SIDE PANELS

Cut 6.

TOP

BOTTOM