SUPERMICR R CONTACT INFORMATION F DRIVERS OR YOUR ...RDIMM, RDIMM, NV-DIMM DDR4 (288-pin) ECC...
Transcript of SUPERMICR R CONTACT INFORMATION F DRIVERS OR YOUR ...RDIMM, RDIMM, NV-DIMM DDR4 (288-pin) ECC...
SUPERMICR R ContaCt InformatIon
• Manuals: http://www.supermicro.com/support/manuals• Drivers & Utilities: http://www.supermicro.com/wftp• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
© 2
019
Sup
erm
icro
Com
pute
r In
c.
All
right
s re
serv
ed.
Rep
rodu
ctio
n of
thi
s do
cum
ent
whe
ther
in p
art
or in
who
le is
str
ictly
pro
hibi
ted
with
out
Sup
erm
icro
's w
ritte
n co
nsen
t. A
ll Tr
adem
arks
are
pro
pert
y of
the
ir re
spec
tive
entit
ies.
All
info
rmat
ion
prov
ided
is d
eem
ed a
ccur
ate
at t
he t
ime
of p
rintin
g; h
owev
er,
it is
not
gua
rant
eed.
PaCkage Contents
X11DaCQuICk referenCe guIDe rev. 1.0c
• One (1) Supermicro Motherboard• Six (6) SATA Cables• One (1) I/O Shield• One (1) Supermicro QRG
• Website: www.supermicro.com • General Information: [email protected]• Technical Support: [email protected]• Phone: +1 (408) 503-8000, Fax: +1 (408) 503-8008
for your system to work ProPerly, Please DownloaD aPProPrIate DrIvers/Images/user's manual from the lInks below:
MN
L-20
82-Q
RG
-10c
WARNING: This product can expose you to chemicals including lead, known to the State of California to cause cancer and birth defects or other reproduc�ve harm. For more informa�on, go to www.P65Warnings.ca.gov.
!
JBT1 CMOS Clear Open (Normal)
JPME1 ME Recovery Pins 1-2 (Normal)
JPME2 Manufacturing Mode Select Pins 1-2 (Normal)
JPS1 SAS Status Pins 1-2 (Enabled)
JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)
BT1 Onboard CMOS battery socket
COM2 COM header for front access
FAN1-6, FANA System/cooling fan headers (FAN1-6, A)
SATA0~3, SATA 4~7 SATA 3.0 headers supported by the PCH
JA1 Audio header for front access
JD1 Speaker/buzzer header (optional) (Note 1)
JF1 Front Control Panel header
JL1 Chassis Intrusion header (Note 2)
JPI2C1 Power Supply SMBus I2C header
JPWR1/JPWR2 8-pin Power Supply connectors
JPWR3 24-pin ATX main power supply connector
JRK1 Intel VROC RAID Key for NVMe SSD
JSPDIF_IN1/JSPDIF_OUT1 SPDIF Audio In/Out headers
JTPM1 Port 80 connector for Trusted Platform Module (TPM)
LAN1/LAN2 Dual 1GbE Ethernet ports on the IO back panel
SAS0~3 SAS Connections 0-3 supported by LSI SAS 3008 Controller
SAS4~7 SAS Connections 4-7 supported by LSI SAS 3008 Controlle
SLOT1 PCI-Express 3.0 x16 Slot supported by CPU1
SLOT2 PCI-Express 3.0 x8 Slot supported by CPU1
SLOT3/SLOT5 PCI-Express 3.0 x16 Slots supported by CPU2
SLOT4/SLOT6 PCI-Express 3.0 x8 Slots supported by CPU2
T-SGPIO1/T-SGPIO2 General Purpose Serial I/O Port1/Port2
USB1/2, USB3/4 Back panel USB 3.0 Ports 1/2, 3/4
USB5/6 Front Accessible USB 3.0 header
VGA VGA Port
DS1 SAS Heartbeat LED Blinking Green: SAS Normal
LE2 Onboard Power LED On: Onboard power on
LEDM1 BMC Heartbeat LED Blinking Green: BMC normal
Back Panel I/O PortsNo. Description No. Description
1. VGA 4. AUDIO1
2. USB 1/2 (USB 3.0) 5. LAN1/2
3. PS2 6. USB 3/4 (USB 3.0)
#1 #2
#3
#4
Small Guiding Post
Large Guiding PostOval DT30 Torx Driver
Use a torqueof 12 lbf·in
Oval C
Printed Triangle
Mounting the Processor Heatsink Moduleinto the CPU socket (on the motherboard)
Tighten the screws in thesequence of 1, 2, 3, 4 (top 3 quarter view)
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features
Installing Processor/Heatsink Module
Notes: 1. Memory speed is dependent on the type of processors used in the system. 2. Using unbal-anced memory topology such as populating two DIMMs in one channel while populating one DIMM in another channel on the same motherboard will result in reduced memory performance. 3. To avoid causing interference with other components, please be sure to use an add-on card that is fully compli-ant with the PCI Standards on a PCI slot card that is fully compliant with the PCI Standards on a PCI slot.
CPU Support
CPU/Heatsink Installation
This motherboard supports dual Intel Xeon Scalable-SP or 2nd Gen Intel Xeon Scalable-SP (Socket P) series processors with support of UltraPath Interconnect (UPI) of up to 10.4 GT/s.
61 54
3
2
A
A
B
B
C
C
Pin 1
Align CPU Pin 1
CPU (Upside Down)w/CPU LGA Lands up
CPU/Heatsink Package(Upside Down)
Align Notch C of the CPUand Notch C of the Processor Clip
Align Notch B of the CPUand Notch B of the Processor Clip
Heatsink(Upside Down)
Fabric CPU and Processor Clip(Upside Down)
CD
d c
a
b
A
B
On Locations of (C, D), the notchessnap onto the heat sink’s
mounting holes
On Locations (A, B), the notchessnap onto the heatsink’s sides
A
B
D C
Triangle on the CPU
Triangle on theProcessor Clip
Make sure MountingNotches snap into place
Power Button
UID LED
NIC1 Active LED
Reset Button
HDD LED
PWR LED
Reset
PWR
3.3V Stby
3.3V Stby
Ground
19
X
Ground
X
3.3V Stby
20
1 2
Ground
Power Fail LED
NIC2 Active LED
NMI
3.3V
3.3V
OH/Fan Fail LED
Notes: 1. Please refer to Chapter 2 of the user's manual for detailed instructions of CPU/Heatsink and memory Installation. 2. Please refer to our website at www.supermicro.com for CPU/Memory support updates. 3. All graphics shown in this quick reference guide are for illustration only. Your components may or may not look the same as the graphics shown in this quick reference guide.
1
43
2
SAS CODE
BIOS LICENSE
DESIGNED IN USA
MAC CODE
MAC CODE
X11DACREV:1.00
BMC
FAN
6FA
N5
JTPM1
JRK1
JA1
JPCIE6
JPCIE4
JPCIE2
JPCIE3
JPCIE1
JPCIE5
JD1
JSPDIF_O
UT1
JSPDIF_IN
1
JL1
Battery
JWD
1
JPME2
JPME1
JPS1
LEDM
1
FAN1FAN2
FAN
A
JPWR3
JPWR2
JPWR1
JPI2C1
JAUDIO1
SATA1
SATA2
SATA3
SATA4
SATA5
SATA8
SATA6
SATA7
FAN
4
FAN
3
JF1
LE2
DS1
T-SGPIO
1
T-SGPIO
2
SAS4~7
USB3~4
CPU2 SLO
T6 PCI-E 3.0 X8
CPU2 SLO
T5 PCI-E 3.0 X16
CPU2 SLO
T4 PCI-E 3.0 X8
CPU2 SLO
T3 PCI-E 3.0 X16
CPU1 SLO
T2 PCI-E 3.0 X8
COM
2
JBT1
CPU1 SLO
T1 PCI-E 3.0 X16
USB 5~6
SAS0~3
VGA
LAN1/2 USB1~2/PS2
CPU2
CPU1
P2 DIM
M D
2
P2 DIM
M D
1
P2 DIM
M E1
P2 DIM
M F1
P1 DIM
M A
2
P1 DIM
M A
1
P1 DIM
M B1
P1 DIM
M C1
P2 DIM
M C1
P2 DIM
M B1
P2 DIM
M A
1
P2 DIMM A2
P1DIM
M F1
P1 DIM
M D
2
P1 DIM
M D
1
P1 DIM
M E1
SAS Controller Chip
PCH
JWD1
SLOT4
SLOT6SLOT5
SLOT3SLOT2SLOT1LEDM1
COM2
JPME2
USB5-6
JTPM1
JRK1
SATA3SATA1
FANAJL1
BatteryFAN6
VGA
FAN5 LAN1/2USB3/4 (3.0)
JPI2C1
JPWR1
JPWR2
JPWR3JF1LE2
P2-DIMMD2P2-DIMMD1P2-DIMME1P2-DIMMF1
P1-DIMMA2P1-DIMMA1P1-DIMMB1P1-DIMMC1
P2-DIMMC1P2-DIMMB1P2-DIMMA1P2-DIMMA2
FAN3FAN4
P1-DIMMD2P1-DIMMD1
P1-DIMME1P1-DIMMF1
FAN1FAN2
CPU1
CPU2
= mounting hole
JBT1
PCI-E M.2 Slot InstallationA Holder B Holder Mount
C Card Holder Mount
Turn 90 degrees to lock
Locked position with M.2 card
Locked positionLocked position
D Plastic screw
STOP
Turn 90 degrees to lock
A+B+C A+B+D
Press in here
B
D
A
BC
A
Rectangle hole on MB
Copyright © 2017 by Super Micro Computer, Inc. All rights reserved.
Hole Location on the MB 42
M.2 Card 60 A+B+C
M.2 Card 80 A+B+C
M.2 Card 110 A+B+D
AUDIOUSB1/2 (3.0)
SATA2
SATA8
SATA6SATA7
SATA5SATA4
LED Indicators
DS1
JPME1
T-SGPIO1T-SGPIO2
JSPDIF_IN1JSPDIF_OUT1
Front Control Panel (JF1)
PS2
Notes: 1. This feature is available when an external speaker/buzzer is used. 2. Please connect a cable from the Chassis Intrusion header at JL1 to the chassis to receive an alert via IPMI. 3. To avoid causing interference with other components, please be sure to use an add-on card that is fully compliant with the PCI-standard on a PCI slot.
Connectors
Jumper
This motherboard supports up to 4TB of 3DS LRDIMM, LRDIMM, 3DS RDIMM, RDIMM, NV-DIMM DDR4 (288-pin) ECC 2933/2666/2400/2133 MHz memory modules in 16 slots. (Notes: 1. 2933 MHz memory is supported by 2nd Gen Intel Xeon Scalable-SP(82xx/62xx) series processors only. 2. Unbalanced memory configuration decreases memory performance and is not recommended.)
Jumpers/Connectors/LED Indicators
JPS1
JA1
JD1