SUNX Panasonic PM-44 PM-54 PM-24 PM-64 Small U … · Small U-shaped Micro Photoelectric Sensor...
-
Upload
truongngoc -
Category
Documents
-
view
224 -
download
0
Transcript of SUNX Panasonic PM-44 PM-54 PM-24 PM-64 Small U … · Small U-shaped Micro Photoelectric Sensor...
457
Related InformationFIBERSENSORS
LASERSENSORS
PHOTOELECTRICSENSORS
MICROPHOTOELECTRIC
SENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORSINDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASUREMENTSENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE INTERFACES
ENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24
PM-44/PM-54
Enables space saving and quick installation!
Equipped with two independent outputsAll models are equipped with two independent outputs Light-ON and Dark-ON.Hence, one model suffices even if the output is to be used differently, depending upon the location of use.Also, since two independent outputs have been provided, cumbersome handling of the output conversion control input, or fear of logic inversion due to a cable break, is eliminated. The sensor can be connected to the existing wiring as it is.
Quick fitting hook-up connectorEasy to maintain connector type models are available. Its exclusive connector is the hook-up connector.Since only crimping with exclusive pliers is to be done, cumbersome soldering or insulation is absolutely not required.Further, connector attached cable is also available.
Crimp the connector on thecable.
Quick connection to the sensor.+V
0 VOutput 1 (Light-ON)Output 2 (Dark-ON)
Connected device sidecan be left as it is.
To PLC
Commercial intermediateconnector
Just connect the cable of the usedoutput (either Light-ON or Dark-ON).
Example of connection with a commercial intermediate connector
Note: Ensure to insulate the unused output wire.
Wide model variety
Meets global requirementsConforms to Europe’s EMC Directive and obtains UL Recognition.The NPN output type with cable (excluding 3 m 9.843 ft cable length type) has also obtained Korea’s S-mark certification.Both, NPN and PNP output models are available.
A wide variety of 12 shapes and 24 models is available. You may select from this wide range to suit the mounting conditions.
Conforming toEMC Directive
PNP output type available
APPLICATIONS
Sensing the starting point and overrun of a moving body
Starting point sensing
Overrun sensing
Overrun sensing
Dog
Starting point and overrun is sensed using the dog on the base.
Certified(Some models only)
Small U-shaped Micro Photoelectric Sensor Amplifier Built-in
PM-44 SERIES PM-54 SERIES
Recognition
General terms and conditions ........... F-17 Sensor selection guide .................. P.441~
Glossary of terms / General precautions ....... P.1359~ / P.1405 Korea’s S-mark .............................. P.1410
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES
ORDER GUIDE
Type Appearance (mm in) Sensing range Model No. Output Output operation
Sm
all
With
cab
le
K ty
pe
26.21.031
25.4 1.000
7 0.276
5 mm 0.197 in(fixed)
PM-K44 NPN open-collector transistor
Incorporated with2 outputs:Light-ON / Dark-ON
PM-K44P PNP open-collector transistor
T ty
pe
13.7 0.539
26.21.031
261.024
PM-T44 NPN open-collector transistor
PM-T44P PNP open-collector transistor
L ty
pe 15.5 0.610
18.5 0.728
26 1.024
PM-L44 NPN open-collector transistor
PM-L44P PNP open-collector transistor
Y ty
pe
25.51.00413.4
0.528
15.5 0.610 PM-Y44 NPN open-collector transistor
PM-Y44P PNP open-collector transistor
F ty
pe
26.21.03113.7
0.539
13.2 0.520
PM-F44 NPN open-collector transistor
PM-F44P PNP open-collector transistor
R ty
pe
26.21.03113.7
0.539
13.2 0.520 PM-R44 NPN open-collector transistor
PM-R44P PNP open-collector transistor
With
con
nect
or
K ty
pe
22.20.87425.4
1.000
7 0.276PM-K54 NPN open-collector transistor
PM-K54P PNP open-collector transistor
T ty
pe
13.7 0.539
22.20.874
26 1.024
PM-T54 NPN open-collector transistor
PM-T54P PNP open-collector transistor
L ty
pe
15.5 0.610
14.5 0.571
26 1.024
PM-L54 NPN open-collector transistor
PM-L54P PNP open-collector transistor
Y ty
pe
21.50.84613.4
0.528
15.5 0.610 PM-Y54 NPN open-collector transistor
PM-Y54P PNP open-collector transistor
F ty
pe
22.20.87413.7
0.539
13.2 0.520
PM-F54 NPN open-collector transistor
PM-F54P PNP open-collector transistor
R ty
pe
22.20.87413.7
0.539
13.2 0.520 PM-R54 NPN open-collector transistor
PM-R54P PNP open-collector transistor
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
459 Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
ORDER GUIDE
3 m 9.843 ft cable length type3 m 9.843 ft cable length type (standard: 1 m 3.281 ft) is also available.When ordering this type, suffix “-C3” to the model No.(e.g.) 3m 9.843 ft cable length type of PM-K44 is “PM-K44-C3”.
OPTIONS
Designation Model No. Description
Connector CN-14 Connector for soldering
Hook-upconnector
CN-14HThis connector can be hooked-up on 0.08 to 0.2 mm2 cable simply in one grip.Wire diameter: ø0.7 to ø1.2 mm ø0.028 to ø0.047 in
CN-14H-2Suitable for UL standard cable.This connector can be hooked-up on 0.18 to 0.22 mm2 cable simply in one grip.Wire diameter: ø1.2 to ø1.52 mm ø0.047 to ø0.060 in
Connectorattached cable
CN-14H-C1Length:1 m 3.281 ftNet weight:20 g approx. For the connector type, with 0.18 mm2
4-core cabtyre cableCable diameter: ø3.8 mm ø0.150 in
CN-14H-C3Length:3 m 9.843 ftNet weight:65 g approx.
Hook-up pliers CN-HP These are exclusive pliers for hook-up connectors CN-14H and CN-14H-2.
Connector• CN-14
Hook-up connector• CN-14H• CN-14H-2
Connector attached cable• CN-14H-C1• CN-14H-C3
Hook-up pliers• CN-HP
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES 460
SPECIFICATIONS
TypeSmall
With cable With connector
Mode
l No. NPN output PM-44 PM-54
Item PNP output PM-44P PM-54PSensing range 5 mm 0.197 in (fixed)
Minimum sensing object 0.8 × 1.8 mm 0.031 × 0.071 in opaque object
Hysteresis 0.05 mm 0.002 in or less
Repeatability 0.03 mm 0.001 in or less
Supply voltage 5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption 15 mA or less
Output
<NPN output type>NPN open-collector transistor
• Maximum sink current: 50 mA• Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 0.7 V or less (at 50 mA sink current)
0.4 V or less (at 16 mA sink current)
<PNP output type>PNP open-collector transistor
• Maximum source current: 50 mA• Applied voltage: 30 V DC or less (between output and +V)• Residual voltage: 0.7 V or less (at 50 mA source current)
0.4 V or less (at 16 mA source current)
Utilization category DC-12 or DC-13
Output operation Incorporated with 2 outputs: Light-ON / Dark-ON
Response time Under light received condition: 20 µs or less, Under light interrupted condition: 100 µs or less(Response frequency: 1 kHz or more) (Note 2)
Operation indicator Vermilion LED (lights up under light received condition)
Env
ironm
enta
l res
ista
nce
Pollution degree 3 (Industrial environment)
Ambient temperature –25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Fluorescent light: 1,000 ℓx at the light-receiving face
EMC EN 60947-5-2
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance 50 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each
Shock resistance 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions for three times each
Emitting element Infrared LED (Peak emission wavelength: 940 nm 0.037 mil, non-modulated)
Material Enclosure: PBT, Slit cover: Polycarbonate, Terminal part [PM-54(P) only]: Solder plated
Cable 0.09 mm2 4-core cabtyre cable, 1 m 3.281 ft long –
Cable extension Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight Net weight: 15 g approx. Net weight: 3 g approx.
DiscDisc 1.8 mm 0.071 in
1.6 mm 0.063 int = 0.2 mm 0.008 in
1.6 mm 0.063 in
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F. 2) The response frequency is the value when the disc, given in the figure below, is rotated.
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
461 Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
I/O CIRCUIT AND WIRING DIAGRAMS
Color code for cable type (Note 2)
(Brown) +V
Load
50 mA max.
50 mA max. (Blue) 0 V
Internal circuit Users’ circuit
Load 5 to 24 V DC ±10 %
+
–
ZD1
ZD2
Tr1
Tr2
(Black) Output 1 (Note 1,3)
Sen
sor c
ircui
t
(White) Output 2 (Note 1,3)
I/O circuit diagram Wiring diagramBrown
Black Load
Load
White
Blue
5 to 24 V DC ±10 %
+
–
Output operation
Color code Output operation
Output 1 Black Light-ON
Output 2 White Dark-ON
PM-44 PM-54 NPN output type
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit.Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) The color code of the connector attached cable is also the same.3) Ensure to insulate the unused output wire.
Symbols … ZD1, ZD2: Surge absorption zener diodeTr1, Tr2 : NPN output transistor
PM-44P PM-54P PNP output type
I/O circuit diagram Wiring diagramColor code for cable type (Note 2)
(Brown) +V
Load
50 mA max.
50 mA max.
(Blue) 0 V
Internal circuit Users’ circuit
Load
5 to 24 V DC ±10 %
+
–
ZD1
ZD2
Tr1
Tr2
(Black) Output 1 (Note 1,3)
Sen
sor c
ircui
t
(White) Output 2 (Note 1,3)
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit.Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) The color code of the connector attached cable is also the same.3) Ensure to insulate the unused output wire.
Brown
Black
Load
Load White
Blue
5 to 24 V DC ±10 %
+
–
SENSING CHARACTERISTICS (TYPICAL)
Sensing position
Dark-ON
Light-ON
Operating point ℓ (mm in)
0 10.039
20.079
30.118
40.157
8.5 mm0.335 in
ℓ
2.9 mm0.114 in
Beamaxis
Dark-ON
Light-ON
Operating point ℓ (mm in)
0 10.039
20.079
30.118
40.157
7 mm0.276 in
ℓ
PM-L44(P)/K44(P) PM-L54(P)/K54(P)
Symbols … ZD1, ZD2: Surge absorption zener diodeTr1, Tr2 : PNP output transistor
Output operation
Color code Output operation
Output 1 Black Light-ON
Output 2 White Dark-ON
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES 464
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
SensorPM-K44 PM-K44P
25.4 1.00019 0.748
19 0.748
2.9 0.114
13.8 0.543
9.5 0.374
Beam axis
13.4 0.528
1 0.039
8.5 0.335
26.21.031 11
0.43310.80.425
40.1572
0.079
50.197
6.40.252
70.276
3.5 0.138
Beam axis
2-ø3.2 ø0.126 mounting holes
2-ø3.8 ø0.150mounting holes
ø2.7 ø0.106 cable, 1 m 3.281 ft longø4.8
ø0.189
Operation indicator(Vermilion)
SensorPM-T44 PM-T44P
13.7 0.539
6.4 0.252
13.4 0.528
8.5 0.335
2.9 0.114
Beam axis
Operation indicator (Vermilion)
5 0.197
26 1.024
3.2 0.126
6.2 0.244
19 0.748
13 0.512
4.3 0.169
2.5 0.098
10.3 0.406
2 0.079 2-mounting
oblong holes
26.2 1.031
10.8 0.425
1 0.039
Beam axis
7 0.276 3 0.118
ø4.8 ø0.189
ø2.7 ø0.106 cable, 1 m 3.281 ft long
SensorPM-L44 PM-L44P
26 1.0243.2
0.126
70.276
18.50.728
20.079
13.40.528
13.4 0.528
Beam axis
2.90.114
15.50.610
3.60.142
190.748
7.20.283
6.50.256
3.30.130
6.40.2525
0.197
8.5 0.3359 0.354
10.80.425
19 0.7481 0.039
4-R2
Beam axis
2-mounting oblong holes
Operation indicator(Vermilion)
ø2.7 ø0.106 cable, 1 m 3.281 ft long
2-ø3.2 ø0.126 mounting holes
ø4.8ø0.189
SensorPM-Y44 PM-Y44P
70.276
3.5 0.138
150.591
7 0.276Beam axis
10.039
25.51.004
10.80.425
20.079
2-ø3.5 ø0.138 mounting holes
ø2.7 ø0.106 cable, 1 m 3.281 ft long
Operation indicator(Vermilion)
ø4.8ø0.189
13.4 0.5285
0.197
8.50.33515.5
0.61012.60.496 6.5
0.256
2.50.098
6.40.252
3.30.130
2.9 0.114
Beam axis
SensorPM-F44 PM-F44P
Beam axis
Beam axis
2.5 0.098
1 0.039
7 0.276
5 0.197
13.4 0.528
13.7 0.539
2.9 0.114
8.5 0.335
26.2 1.031 13.6
0.535
9 0.354
13.2 0.520
3.2 0.126
6.4 0.252
7 0.276
7 0.276
4 0.157 3.3 0.130
2 0.079
10.8 0.425
Operation indicator (Vermilion)
ø2.7 ø0.106 cable, 1 m 3.281 ft long
ø4.8 ø0.189 2-ø3.5 ø0.138 mounting holes
SensorPM-R44 PM-R44P
Beam axis
Beam axis
2.50.098
10.039
13.70.539
13.4 0.528
70.276
2.90.114
13.20.520
6.40.2523.2
0.126 70.276
90.354
13.60.535
70.276
3.3 0.1304 0.157
2-ø3.5 ø0.138mounting holes
8.50.335
26.21.031
10.80.425
20.079
50.197
ø4.8ø0.189
ø2.7 ø0.106 cable,1 m 3.281 ft long
Operation indicator(Vermilion)
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
465 Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
SensorPM-K54 PM-K54P
25.4 1.00019 0.748
19 0.748
2.9 0.114
13.80.543
5.5 0.217
Beam axis
13.4 0.528
1 0.039
8.50.335
22.20.874 11
0.433 6.80.268
5 0.197
5 0.197 6.40.252
70.276
3.50.138
Beam axis
2-ø3.2 ø0.126 mounting holes
2-ø3.8 ø0.150 mounting holes
Operation indicator(Vermilion)
SensorPM-T54 PM-T54P
13.7 0.539
6.40.252
13.4 0.528
8.5 0.335
2.90.114
Beam axis
Operation indicator(Vermilion)
50.19726
1.024
3.20.126
6.20.244
190.748
130.512
4.30.169
2.50.098
6.30.248
5 0.197
2-mounting oblong holes
22.20.874
6.80.268
10.039
Beam axis
7 0.27630.118
SensorPM-L54 PM-L54P
26 1.0243.2
0.126
70.27614.5
0.571
50.197
13.40.528
13.4 0.528
Beam axis
2.90.114
15.50.610
3.60.142
190.748
7.20.283
6.50.256
3.30.130
6.40.252
50.197
8.5 0.3359 0.354
6.80.268
19 0.7481 0.039 4-R2 R0.079
Beam axis
2-mounting oblong holes
Operation indicator(Vermilion)
2-ø3.2 ø0.126 mounting holes
SensorPM-Y54 PM-Y54P
7 0.276
3.5 0.138
11 0.433
7 0.276 Beam axis
1 0.039
21.5 0.846
5 0.197
6.8 0.268
2-ø3.5 ø0.138 mounting holes
Operation indicator (Vermilion)
13.4 0.528
5 0.197
8.5 0.335 15.5
0.610 12.6 0.496 6.5
0.256
2.5 0.098
6.4 0.252
3.3 0.130
2.9 0.114
Beam axis
Beam axis
Beam axis
2.5 0.098
1 0.039
7 0.276
13.4 0.528
5 0.197
13.7 0.539
2.9 0.114
8.5 0.335
6.8 0.268
22.2 0.874 13.6
0.535
9 0.354
13.2 0.520
3.2 0.126
6.4 0.252
7 0.276
7 0.276
3.3 0.130 5 0.197
Operation indicator (Vermilion) 2-ø3.5 ø0.138 mounting holes
SensorPM-R54 PM-R54P
Beam axis
Beam axis
2.5 0.098
1 0.039
13.7 0.539
13.4 0.528
7 0.276
2.9 0.114
13.2 0.520 6.4
0.252 3.2 0.126 7
0.276 9
0.354
13.6 0.535
7 0.276
3.3 0.130
2-ø3.5 ø0.138 mounting holes
8.5 0.335
22.2 0.874
6.8 0.268
5 0.197
5 0.197
Operation indicator (Vermilion)
SensorPM-F54 PM-F54P
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Small U-shaped Micro Photoelectric Sensor PM-44 SERIES PM-54 SERIES 466
Connector (Optional)CN-14
13 0.512
+V 1 2 0V +V 1 2 0V
t 0.4 t 0.016 0.8 0.031 1.6 0.063
(2.54) (0.100) (7.62)
(0.300)
2 0.079
1 0.039
6 0.236
1 0.039
1 0.039
4.6 0.181
7.5 0.295
(5) (0.197)
Hook-up connector (Optional)CN-14H CN-14H-2 Connector attached cable (Optional)CN-14H-C1 CN-14H-C3
+V 1 2 0V
+V 1 2 0V
+V 1 2 0V
13 0.512
15 0.591
6 0.236
+V
1 2
0V
15 0.591
(50) (1.969) (8)
(0.315)
L
ø3.8 ø0.150 cable
13 0.512
6 0.236
Model No. Length L
CN-14H-C1 1 m 3.281 ft
CN-14H-C3 3 m 9.843 ft
• Length L
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
+V
10.039
10.039
t 0.3t 0.0122.1
0.0831.60.063
0.80.031
2.540.100
2.540.100
2.540.100
1.30.051
1 2 0V
* Terminal part (PM-54, PM-54P)
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
451
Related InformationFIBERSENSORS
LASERSENSORS
PHOTOELECTRICSENSORS
MICROPHOTOELECTRIC
SENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORSINDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASUREMENTSENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE INTERFACES
ENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24
PM-44/PM-54
Extremely small size and space saving
PM-24 series contributes to the miniaturization or space saving of your equipment.
Equipped with two independent outputs
All models are equipped with two independent outputs-Light-ON and Dark-ON.Hence, one model suffices even if the output is to be used differently, depending upon the location of use.Also, since two independent outputs have been provided, cumbersome handling of the output conversion control input, or fear of logic inversion due to a cable break, is eliminated. The sensor can be connected to the existing wiring as it is.
25.4 mm1.000 in
22.3mm
0.878 in
11 mm0.433 in
Previousmodel
22 mm0.866 in
12 mm0.472 in
Ultra-small typePM-K24(-R)
( )
Wide model variety
A wide variety of 5 shapes and 15 models is available. You may select from this wide range to suit the mounting conditions.
Conforming toEMC Directive
Recognition
PM-24 SERIES
Extremely small size enables space saving!!
Certified(Some models only)
Ultra-small U-shaped Micro Photoelectric Sensor Amplifier Built-in
General terms and conditions ........... F-17 Sensor selection guide .................. P.441~
Meets global requirements
Conforms to Europe’s EMC Directive and obtains UL Recognition.Both, NPN and PNP output models are available.The PM-24 has also obtained Korea’s S-mark certification.
Note: Ensure to insulate the unused output wire.
+V0 VOutput 1 (Light-ON)Output 2 (Dark-ON)
Connected device sidecan be left as it is.
To PLC
Commercial intermediate connector
Just connect the cable of the usedoutput (either Light-ON or Dark-ON).
Example of connection with a commercial intermediate connector
Glossary of terms / General precautions ....... P.1359~ / P.1405 Korea’s S-mark .............................. P.1410
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Ultra-small U-shaped Micro Photoelectric Sensor PM-24 SERIES
Type Appearance (mm in) Sensing range Model No. (Note) Output Output operation
Ultr
a-sm
all
K ty
pe
120.472
22 0.866
6 0.236
5 mm 0.197 in(fixed)
PM-K24 NPN open-collector transistor
Incorporated with 2 outputs: Light-ON / Dark-ON
PM-K24P PNP open-collector transistor
PM-K24-R NPN open-collector transistor
L ty
pe 12 0.472
10.50.413
13.4 0.528
PM-L24 NPN open-collector transistor
PM-L24P PNP open-collector transistor
PM-L24-R NPN open-collector transistor
F ty
pe 10.5 0.413
120.472
13.40.528
PM-F24 NPN open-collector transistor
PM-F24P PNP open-collector transistor
PM-F24-R NPN open-collector transistor
R ty
pe
10.5 0.413
120.47213.4
0.528
PM-R24 NPN open-collector transistor
PM-R24P PNP open-collector transistor
PM-R24-R NPN open-collector transistor
U ty
pe
160.63013.4
0.528
6 0.236
PM-U24 NPN open-collector transistor
PM-U24P PNP open-collector transistor
PM-U24-R NPN open-collector transistor
3 m 9.843 ft cable length type3 m 9.843 ft cable length type (standard: 1 m 3.281 ft) is also available. (excluding flexible cable type and PNP output type)When ordering this type, suffix “-C3” to the model No.(e.g.) 3m 9.843 ft cable length type of PM-K24 is “PM-K24-C3”.
OPTIONS
Designation Model No. Description
Mounting screw MS-M2Mounting screw with washers for the ultra-small type sensor (50 pcs. lot). It can mount securely as it is spring washer attached.
Mounting screw•MS-M2
Note: The suffix “-R” indicates a flexible cable type.
ORDER GUIDE
Starting point
The starting point can be sensed by making a slit in the rotating body.
APPLICATIONS
Sensing the starting point on a rotating body
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
453 Ultra-small U-shaped Micro Photoelectric Sensor PM-24 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
SPECIFICATIONS
TypeUltra-small
With flexible cable
Mode
l No. NPN output PM-24 PM-24-R
Item PNP output PM-24P –
Sensing range 5 mm 0.197 in (fixed)
Minimum sensing object 0.8 × 1.8 mm 0.031 × 0.071 in opaque object
Hysteresis 0.05 mm 0.002 in or less
Repeatability 0.03 mm 0.001 in or less
Supply voltage 5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption 15 mA or less
Output
<NPN output type>NPN open-collector transistor
• Maximum sink current: 50 mA• Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 0.7 V or less (at 50 mA sink current)
0.4 V or less (at 16 mA sink current)
<PNP output type>PNP open-collector transistor
• Maximum source current: 50 mA• Applied voltage: 30 V DC or less (between output and + V)• Residual voltage: 0.7 V or less (at 50 mA source current)
0.4 V or less (at 16 mA source current)
Utilization category DC-12 or DC-13
Output operation Incorporated with 2 outputs: Light-ON / Dark-ON
Response timeUnder light received condition: 20 µs or lessUnder light interrupted condition: 100 µs or less(Response frequency: 1 kHz or more) (Note 2)
Operation indicator Vermilion LED (lights up under light received condition)
Env
ironm
enta
l res
ista
nce
Pollution degree 3 (Industrial environment)
Ambient temperature (Note 3, 4) –25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Fluorescent light: 1,000 ℓx at the light-receiving face
EMC EN 60947-5-2
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance 50 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each
Shock resistance 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions for three times each
Emitting element Infrared LED (Peak emission wavelength: 940 nm 0.037 mil, non-modulated)
Material Enclosure: PBT, Slit cover: Polycarbonate
Cable 0.09 mm2 4-core cabtyre cable [PM-24-R: 0.1 mm2 flexible, oil and heat resistant cabtyre cable (Note 5)], 1 m 3.281 ft long
Cable extension Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight Net weight: 10 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.2) The response frequency is the value when the disc, given in the figure below, is rotated.
3) In case the PM-24 series is used at an ambient temperature of +50 °C +122 °F, or more, make sure to mount it on a metal body.4) Take care that the flexibility of the PM-24-R cable is lost if the ambient temperature in –10 °C +14 °F or less.5) The cable of PM-24-R is a flexible cable usable on a moving base. When the sensor is mounted on a moving base, fix the sensor cable joint so that
stress is not applied to it. (Models other than the PM-24-R cannot be used on a moving base.)
Disc
Disc 1.8 mm 0.071 in
1.6 mm 0.063 int = 0.2 mm 0.008 in
1.6 mm 0.063 in
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Ultra-small U-shaped Micro Photoelectric Sensor PM-24 SERIES 454
I/O CIRCUIT AND WIRING DIAGRAMS
PM-24 PM-24-R NPN output type
I/O circuit diagram Wiring diagram
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit. Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) Ensure to insulate the unused output wire.
Output operationColor code Output operation
Output 1 Black Light-ON
Output 2 White Dark-ON
Symbols … ZD1, ZD2: Surge absorption zener diodeTr1, Tr2 : NPN output transistor
Color code
Sen
sor c
ircui
t
(Brown) +V
5 to 24 V DC±10 %
+
–
(Blue) 0 V
Users’ circuit Internal circuit
ZD1
ZD2
Tr2
Tr1
50 mA max.
50 mA max.
(Black) Output 1 (Note 1,2)
(White) Output 2 (Note 1,2)
Load Load
Brown
5 to 24 V DC±10 %
+
–
Black
White
Blue
Load Load
PM-24P PNP output type
I/O circuit diagram Wiring diagram
Output operationColor code Output operation
Output 1 Black Light-ON
Output 2 White Dark-ON
Color code
Sen
sor c
ircui
t
(Brown) +V
5 to 24 V DC±10 %
+
–
(Blue) 0 V
Users’ circuit Internal circuit
ZD1
ZD2
Tr2
Tr1 50 mA max.
50 mA max. (Black) Output 1 (Note 1,2)
(White) Output 2 (Note 1,2) Load Load
Brown
5 to 24 V DC±10 %
+
–
Black
White
Blue Load
Load
SENSING CHARACTERISTICS (TYPICAL)
Sensing position
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit. Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) Ensure to insulate the unused output wire.
Symbols … ZD1, ZD2 : Surge absorption zener diodeTr1, Tr2 : PNP output transistor
Dark-ON
Light-ON
Operating point ℓ (mm in)
ℓ
0 10.039
Beamaxis
2 mm0.079 in
5.5 mm0.217 in
20.079
30.118
40.157
Dark-ON
Light-ON
ℓ
0
6 mm0.236 in
10.039
20.079
30.118
40.157
Operating point ℓ (mm in)
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Ultra-small U-shaped Micro Photoelectric Sensor PM-24 SERIES 456
SensorPM-K24(P) PM-K24-R SensorPM-L24(P) PM-L24-R
SensorPM-F24(P) PM-F24-R SensorPM-R24(P) PM-R24-R
SensorPM-U24(P) PM-U24-R
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
Beam axis
Beam axis
4 0.157
3 0.118
6 0.236
2 0.079
13.4 0.528
18 0.709 22 0.866
5 0.197
2 0.079
ø4.8 ø0.189
5.5 0.217
12 0.472
8 0.315
Operation indicator (Vermilion)
2-ø2.5 ø0.098 mounting holes
ø2.7 ø0.106 cable, 1 m 3.281 ft long
Beam axis
Beam axis
5.5 0.217
30.118
10.50.413
20.079
13.40.528
10 0.3944 0.157
50.197
60.236
5.5 0.217120.472
80.315
Operation indicator(Vermilion)
2-ø2.5 ø0.098 mounting holes
ø2.7 ø0.106 cable, 1 m 3.281 ft long
Beam axis
Beam axis
1.5 0.059
30.118
6.70.264
10.50.413
20.079
20.079
ø2ø0.079
40.157
13.40.528
4 0.157
50.197
60.2365.5
0.217 5.50.217
120.472
80.315
Operation indicator(Vermilion)
ø4.8ø0.189
ø2.7 ø0.106 cable,1 m 3.281 ft long
ø2.5 ø0.098 mounting hole
Beam axis
Beam axis
1.5 0.059
30.118
6.70.264
10.50.413
20.079
20.079
ø2ø0.079
4 0.157
40.157
13.40.528
50.197
60.236
5.5 0.217
5.50.217
120.472
80.315
Operation indicator(Vermilion)
ø4.8ø0.189
ø2.7 ø0.106 cable, 1 m 3.281 ft long
ø2.5 ø0.098 mounting hole
Beam axis
Beam axis
30.118
160.630
20.079
13.40.528
50.197
60.236
5.5 0.21712
0.472
80.315
Operation indicator(Vermilion)
ø2.7 ø0.106 cable, 1 m 3.281 ft long
2-ø2.5 ø0.098 mounting holes
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Related InformationFIBERSENSORS
LASERSENSORS
PHOTOELECTRICSENSORS
MICROPHOTOELECTRIC
SENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORSINDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASUREMENTSENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE INTERFACES
ENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24
PM-44/PM-54
443PM-64 SERIES
Easy connection with a single touchusing commercially-available connectors
Conforming toEMC Directive
Built-in connector saves spaceThis greatly reduces the amount of space taken up compared to previous models.The dimension between the beam axis and cable bending part has been reduced to half at maximum.
2.1 mm 0.083 in
26 mm 1.024 in
PM-64
23 mm 0.906 in
Previous model Connector type
Approximately60 %
of previousmodel
25.4 mm 1.000 in
11 mm 0.433 in
22.3 mm 0.878 in
Can be connected using commercially-available connectorsThe connector connection type eliminates the extra work of soldering and insulation processing. In addition, the connector used is a commercially-available multi-purpose connector which is also currently used by the DP-100 series of digital pressure sensors.
Digital pressure sensorDP-100 series
DetachableCommercially-available connector
Connector Built-in U-shaped Micro Photoelectric Sensor Amplifier Built-in
General terms and conditions ........... F-17 Sensor selection guide .................. P.441~
Glossary of terms ........................ P.1359~ General precautions ..................... P.1405
Recognition
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES
Improved maintenance and workability significantly reduces total costThe processing cost of the connector cables can be drastically reduced through the use of commercially-available crimping connectors.
• Automation is hard because of soldering. • Insulation processing is required.• A large space is necessary at the terminal area.• Connectors are not reliable
(not fully connected or seated).
• Crimping processing is required in two places.• A set of commercially-available connectors is
necessary.• There are many processes for cable connections. • An intermediate box is required.
Previous model (Soldering: Connector type)
Previous model (Converted to the cable-type commercially-available connector)
PM-64 series (Commercially-available connectors can be used) • Crimping processing makes automation possible so the connectors are also highly reliable.
• Soldering, insulation processing, and an intermediate box are not necessary.
• Connectors are widely available.• Mounting in a small space is easy.• Strongly connected using a locking connector.• 1 m 3.281 ft, 2 m 6.562 ft, 3 m 9.843 ft, and 5 m
16.404 ft connector cables are available.
Insulation processing
Intermediate box Commercially-available connector
Soldering
Crimping processing
Crimping processing
Suggestion
Starting point and overrun is sensed using the dog on the base.
Starting point sensing
Overrun sensing
Overrunsensing
Dog StartingpointThe starting
point can be sensed by making a slit in the rotating body.
Pallet is stopped by sensing the dog.
APPLICATIONS
Determining the pallet position Sensing the starting point and overrun of a moving body
Sensing the starting pointon a rotating body
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
445
Type Appearance (mm in) Sensing range Model No. Output Output operation
Sm
all a
nd b
uilt-
in c
onne
ctor
type
K ty
pe
230.906 in
26 1.024 in7 0.207 in
5 mm 0.197 in (fixed)
PM-K64 NPN open-collector transistor
Incorporated with 2 outputs:Light-ON / Dark-ON
PM-K64P PNP open-collector transistor
T ty
pe
230.906 in
26 1.024 in
13.7 0.539 inPM-T64 NPN open-collector
transistor
PM-T64P PNP open-collector transistor
PM-T64W(Note)
NPN open-collector transistor
L ty
pe
15.7 0.618 in26.2 1.031 in
15.5 0.610 in
PM-L64 NPN open-collector transistor
PM-L64P PNP open-collector transistor
Y ty
pe
22.70.894 in13.8 0.543 in
15.5 0.610 in PM-Y64 NPN open-collector transistor
PM-Y64P PNP open-collector transistor
F ty
pe
230.906 in
14 0.551 in
13.4 0.528 in
PM-F64 NPN open-collector transistor
PM-F64P PNP open-collector transistor
R ty
pe
230.906 in
14 0.551 in
13.4 0.528 in
PM-R64 NPN open-collector transistor
PM-R64P PNP open-collector transistor
ORDER GUIDE
Designation Model No. Description
Connectorattachedcable
CN-14A-C1 Length: 1m 3.281 ft
0.2 mm2 4-core cabtyre cable with connector on one endCable outer diameter: ø3.7mm
ø0.146 in
CN-14A-C2 Length: 2m 6.562 ft
CN-14A-C3 Length: 3m 9.843 ft
CN-14A-C5 Length: 5m 16.404 ft
Connectorattachedcable Flexible cable
CN-14A-R-C1 Length: 1m 3.281 ft
CN-14A-R-C2 Length: 2m 6.562 ft
CN-14A-R-C3 Length: 3m 9.843 ft
CN-14A-R-C5 Length: 5m 16.404 ft
Connector CN-14A Set of 10 housings and 40 contacts
• CN-14A(-R)-C
Connector attached cable
• CN-14A
Connector
Housing
Contact
4
Recommended connectorContact: SPHD-001T-P0.5, Housing: PAP-04V-S (Manufactured by J.S.T. Mfg. Co., Ltd.)
Recommended crimping toolModel No. : YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.)
OPTIONS
Note: Contact the manufacturer for details of the recommended products.
Note: Contact the manufacturer for details of the recommended products.
Note: PM-T64W is compatible with our conventional PM-T53(B).
230.906 in
16.7 0.657 in
26 1.024 in
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES 446
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.2) This is the value when a sensing object is moved in a lateral direction to the U-shape. 3) This is the value when a sensing object is moved in a lateral direction to the U-shape and when the inserting length of the sensing board is 5 mm 0.197 in.4) The response frequency is the value when the disc, given in the figure below, is rotated.
TypeSmall and built-in connector type
K type T type L type Y type F type R type
Mode
l No. NPN output PM-K64 PM-T64(W) PM-L64 PM-Y64 PM-F64 PM-R64
Item PNP output PM-K64P PM-T64P PM-L64P PM-Y64P PM-F64P PM-R64PSensing range 5 mm 0.197 in (fixed)
Minimum sensing object 0.8 × 1.8 mm 0.031 × 0.071 in opaque object
Hysteresis 0.05 mm 0.002 in or less (Note 2)
Repeatability 0.01 mm 0.0004 in or less (Note 3)
Supply voltage 5 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption 15 mA or less
Output
<NPN output type>NPN open-collector transistor
• Maximum sink current: 50 mA• Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 0.7 V or less (at 50 mA sink current)
0.4 V or less (at 16 mA sink current)
<PNP output type>PNP open-collector transistor
• Maximum source current: 50 mA• Applied voltage: 30 V DC or less (between output and +V)• Residual voltage: 0.7 V or less (at 50 mA source current)
0.4 V or less (at 16 mA source current)
Utilization category DC-12 or DC-13
Output operation Incorporated with 2 outputs: Light-ON / Dark-ON
Response timeUnder light received condition: 20 µs or lessUnder light interrupted condition: 100 µs or less(Response frequency: 1 kHz or more) (Note 4)
Operation indicator Orange LED (lights up under light received condition)
Env
ironm
enta
l res
ista
nce
Pollution degree 3 (Industrial environment)
Ambient temperature –25 to +55 °C –13 to +131 °F (No dew condensation or icing allowed), Storage: –30 to +80 °C –22 to +176 °F
Ambient humidity 35 to 85 % RH, Storage: 5 to 95 % RH (Note 5)
Ambient illuminance Fluorescent light: 1,000 ℓx at the light-receiving face
EMC EN 60947-5-2
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance 50 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each
Shock resistance 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions for three times each
Emitting element Infrared LED (Peak emission wavelength: 940 nm 0.037 mil, non-modulated)
Material Enclosure: PBT, Slit cover: Polycarbonate
Cable length Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 6)
Weight Net weight: 3 g approx.
SPECIFICATIONS
5) 5-35% RH in an ambient temperature of +23 °C +73.4 °F.6) Confirm that the sensor terminal voltage is more than 4.5 V when using an extension of over 20 m 65.617 ft.
DiskDisk 1.8 mm 0.071 in
1.6 mm 0.063 int = 0.2 mm 0.008 in
1.6 mm 0.063 in
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
447
I/O CIRCUIT AND WIRING DIAGRAMS
I/O circuit diagram
Users’ circuit Internal circuit
50 mA max.
50 mA max.
ZD1
Tr1
Load Load
(Brown) +V (Black) Output 1 (Note 1,2)
(White) Output 2 (Note 1,2)
(Blue) 0 V
Sen
sor c
ircui
t
ZD2
Tr2
5 to 24 V DC±10 %
+
–
Color code of connector attached cable
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit. Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) Ensure to insulate the unused output wire.
Terminal arrangement diagram
4321
Terminal No. Designation
1 +V
2 Output1: Light-ON
3 Output2: Dark-ON
4 0 V
PM-64(W) NPN output type
Symbols … ZD1, ZD2 : Surge absorption zener diodeTr1,Tr2 : NPN output transistor
I/O circuit diagram
Users’ circuit Internal circuit
50 mA max.
50 mA max.
ZD1
Tr1
Load Load
(Brown) +V
(Black) Output 1 (Note 1,2)
(White) Output 2 (Note 1,2) (Blue) 0 V
Sen
sor c
ircui
t
ZD2
Tr2
Color code of connector attached cable
5 to 24 V DC ±10 %
+
–
Notes: 1) Make sure to connect terminals correctly as the sensor does not incorporate a reverse polarity protection circuit. Further, the output is not incorporated with a short-circuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Faulty wiring may result in damage.
2) Ensure to insulate the unused output wire.
Terminal arrangement diagram
4321
Terminal No. Designation
1 +V
2 Output1: Light-ON
3 Output2: Dark-ON
4 0 V
PM-64P PNP output type
SENSING CHARACTERISTICS (TYPICAL)
PM-K64(P) PM-L64(P)
Sensing position
Symbols … ZD1, ZD2 : Surge absorption zener diodeTr1,Tr2 : PNP output transistor
Dark-ON
Light-ON 0 1
0.0392
0.0793
0.1184
0.157Operating point ℓ (mm in)
ℓ
2.6 mm0.102 in
9 mm 0.354 in
Beamaxis
ℓ
Dark-ON
Light-ON 1
0.0392
0.0793
0.1184
0.157Operating point ℓ (mm in)
7 mm 0.276 in
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES
Selection Guide
U-shaped
Convergent Reflective
PM-64
PM-24PM-44/PM-54
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORS
STATIC CONTROLDEVICES
ENDOSCOPE
LASERMARKERS
PLC /TERMINALS
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
449
SensorPM-T64(P)SensorPM-K64(P)
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
Operation indicator (Orange)
Beam axis
Beam axis
2-ø3.2 ø0.126 mounting holes
6.8 0.268
7.4 0.291
3.2 0.126
2.1 0.083
5 0.197
7 0.276
13.8 0.543
2.6 0.102
20 0.787
20 0.787
3.7 0.146
1.7 0.067
26 1.024
Locking part
3.5 0.138
2-mounting oblong holes Connector attached cable CN-14A(-R)-C (Optional)
Beam axis width: 0.8 0.031
23 0.906
9 0.354
( )
13.4 0.528
Beam axis width: 0.8 0.031
2.1 0.083 Locking
part
7 0.276
3 0.118
7 0.276
9 0.354
23 0.906
Beam axis
Beam axis
13.4 0.528
5 0.197 2.6
0.102
7.4 0.291
20 0.787
26 1.024
6.2 0.244
3.2 0.126
1.6 0.063
4.1 0.161
Operation indicator (Orange)
2-mounting oblong holes
Connector attached cable CN-14A(-R)-C (Optional)
13.7 0.539
13 0.512
( ) 10.5 0.413
SensorPM-L64(P)SensorPM-T64W
SensorPM-Y64(P)
Beam axis
Beam axis
6.4 0.252
7.2 0.283
7 0.276
8.3 0.327
13.4 0.528
5 0.197
12.8 0.504
3.2 0.126
3.5 0.138
2.6 0.102
26.2 1.031
2-ø3.2 ø0.126 mounting holes
20 0.787 1.7 0.067
3.7 0.146
2-mounting oblong holes
Operation indicator (Orange) Locking part
Connector attached cable CN-14A(-R)-C (Optional)
2.1 0.083
Beam axis width: 0.8 0.031
PM-L64
PM-L64
15.7 0.618
( )
15.5 0.610
9 0.354
9 0.354
20 0.787
12.8 0.504
2.1 0.083
Connector attached cable CN-14A(-R)-C (Optional)
2-ø3.5 ø0.138 mounting holes
Operation indicator (Orange)
Locking part
Beam axis
Beam axis
6.4 0.252
2.5 0.098
6.5 0.256
9 0.354 5
0.197
15.5 0.610
7 0.276
3.5 0.138
7 0.276
2.6 0.102
Beam axis width: 0.8 0.031
22.7 0.894
( )
12.9 0.508
13.8 0.543
SensorPM-F64(P)
ø3.2 ø0.126 mounting holes
Operation indicator (Orange)Center of beam axis and boss
50.197
2.50.098
30.118
90.354
70.276
8.20.323
2.60.102
Center of beam axis and boss
ø2.4 ø0.094
Beam axis and boss
70.276
70.276Connector attached cable
CN-14A(-R)-C (Optional)
Locking part2.1
0.083
Beam axis width: 0.8 0.031
13.40.528
230.906
( )
16.30.642
140.551
Connector attached cable CN-14A(-R)-C (Optional)
Operation indicator (Orange)
2-mounting oblong holes
16.70.657
100.394
70.276
90.354
10.50.413
40.157
50.197
13.40.528
1.60.063
4.10.161
261.024
2.60.102
230.906
7.40.291
130.512
3.20.126
60.236
Beam axis
Beam axis
Beam axis width: 0.8 0.031
200.787
Locking part
2.10.083( )
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m
Connector Built-in U-shaped Micro Photoelectric Sensor PM-64 SERIES
CN-14A-C CN-14A-R-C Connector attached cable (Optional)
Model No. Length L
CN-14A(-R)-C1 1,000 39.370
CN-14A(-R)-C2 2,000 78.740
CN-14A(-R)-C3 3,000 118.110
CN-14A(-R)-C5 5,000 196.850
• Length L
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
SensorPM-R64(P)
Connector attached cable CN-14A(-R)-C (Optional)
ø3.2 ø0.126 mounting holes
Operation indicator (Orange)Center of beam axis and boss
50.197
13.40.528
2.50.098
30.118
90.354
70.276
8.20.323
2.60.102
Center of beam axis and boss
ø2.4ø0.094
Beam axis and boss
70.276
70.276
Beam axis width: 0.8 0.031
2.10.083
Locking part
16.30.642
140.551
( )
230.906
351.378
80.315
501.969
L
ø3.7 ø0.146 cable
( )( ) 8
0.315( )( )
Prod
ukte
, Sup
port
und
Ser
vice
Rug
ghöl
zli 2
CH
- 54
53 B
ussl
inge
nTe
l. +4
1 (0
)56
222
38 1
8Fa
x +4
1 (0
)56
222
10 1
2m
ailb
ox@
sent
roni
c.co
mw
ww
.sen
troni
c.co
m