SUNRISESUNRISE

The NEW The NEW ENERGYENERGY

contentcontent::1. Kinds of solar systems

Thermo-siphon systems Year-round solar systems Heat-supporting systems

2. Products with SUNRISE Panel collectors Boilers Elements of solar system

3. Project program4. Mounting of solar system

Thermo-siphon systems

SUNRISE 1. Insulation layer

2. Water holder with heat carrier

3. Water container

The heat carrier goes into the lower part of PC-[4],absorbs the sun energy accumulated by the copper absorber and upper part of the panel-collector, goes into the upper part of the boiler, flows over the water holder and provides its heat to the water inside. There are two outputs on the upper part of the boiler. The first one is used for filling the system with heat carrier [PG],an expansion vessel [6] is fixed on the second one.

 

All-year solar system-boiler with 0ne serpentine SUNRISE

Elements:

1. Water holder

2. Panel collector

3. Pump group

4. Filter RAW

5. Digital control

6. Expansion vessel

7. Back valve

8. Spherical tap

9. Filling taps

10. Thermo-sensor

5

Year-round solar system -

boiler with two serpentines SUNRISE

Elements1. Панельный коллектор 2,15 м22. Контрллер дельта Сол3. Термодатчик4. Насосная группа5. Расширительный бак6. Фильтр7. Заполняющий клапан8. Обратный клапан9. Шаровый кран10. Циркуляционный насос11. Обратный клапан12. Котел13. На систему отопления14. Расширительный бак для

системы отопления15. Трехходовой клапан

2

Heat supporting systems

SUNRISE

Elements 1. Heating installation2. Circulation pump3. Circulation pump4. Back valve 5. Generator 6. Magnet valve 7. Thermo sensor /cold heat-carrier from the

heating installation / 8. Expansion vessel for heating install.9. Thermo sensor /hot heat-carrier from the

heating installation 10. Thermo- sensor /t° of the boiler for domestic

hot water / 11. Combo - boiler12. Solar collector 13. Expansion vessel for solar installation 14. Pump group for solar installation 15. Filter 16. Thermo- sensor /hot heat-carrier from the

solar installation / .17. Water holder for domestic hot water.18. Thermo-sensor / lower part of the boiler-

Dom. hot water/

13

14

Panel collectors Select Advantages of panel collector SELECT: - special polymeric coating of the carrying aluminum construction, reducing the

heat loss.

- the absorber material made of copper tin -TINOX coating.   Characteristics of absorber TINOX Classic:   -solar coefficient of Absorbing : 95 % ± 2 %     -heat coefficient of Emitting :  5 % ± 3 % TINOX Art-Line:  - solar coefficient of Absorbing : 95 % ± 1 %     -heat coefficient of Emitting :   5 % ± 1 %        - heat carrier – liquid : PG - transformation capacity degree: 600 kWh/ м² Annually - Absorber : copper - Coating : TINOX Classic and Art-Line                                                        

Panel collector Standard panel collectors Standard are mainly designed for domestic

hot water seasonal systems and for the period April-October are able to cover the needs of warm water up to 80 - 100 %.

The absorber is made of copper elements. The special black coating absorbs maximum sun rays. The frame is made of special aluminum profile. The collector glass is designed for maximal omission of the

sum rays. The insulation is of mineral wadding. Technical data of panel collectors StandardAbsorber: copperCoefficient of absorbing : 95%Reflection : 5%Transformation degree : 364 kWh / m22 annuallyCoating: solar lacquer

0

20

40

60

80

100

I II III IV V VI VII VII IX X XI XII

Select

Standard

Hollander connection

Panel collectors Select / Standard

Standard Select

Vacuum tube collector

SUNRISE

The used materials provide long and efficient work for min. 20 years.

The strength of the connections between the glass tubes and absorber allow better vacuum field for better insulation.

The highly selective layer is sealed in high quality vacuum field, protected from outer influence and oxidation which improves its efficiency.

The vacuum tubes are changeable. The double glass tubes are without metal coating for absolute density.The hollowness of the absorbing tube allow maximal unobstructed heat flowing.

Technical data: size: 1 684 х 765 х 100 мм weight 20 kg. surface 1,29 м². pressure resistance - мах. 6 bar heat – carrier Tyfocor HTL - 3,2 liters. transformation capacity of 4 collector system : 730kWh/ м². heating energy and safety /EN 129752 hailstorm resistance DIN/EN 129752 coefficient efficiency > 99 % Mounting:

-Roof mounting-Flat roof or wall mounting-Min. inclination angle of the panel collector to be - 1500

Curve of effectiveness at 800W/m2 2 emission emission

Eff

icie

nc

y

h

1.Solar stations. 2. Flexible joining connection.3. Hand pump. 4. Flow-meter. 5. Filling element.6. Draining element.7. Air vent.8. Filter. 9. Joining tee.10. Filling tap.11. Mixing valve.12. Back valve.13. Stainless flexible tube.14. Stainless flexible tube.15. Nipple straight /female-outer/16. Capillary welding connection.17. Nipple double ¾`` /outer threading/

18. Expansion vessel

Mounting scheme SUNRISE

Elements for solar system

SUNRISE

Elements

1. Solar air vent.

2. Manometer with balancing valve.

3. Thermometer with stopping tap.

4. Pump .

5. Flow meter.

Elements for solar system

SUNRISE

Elements

1. Filter RAW.

2. Back valve.

3. Expansion vessel.

4. Filling tap.

Sample connection scheme SUNRISE

NEW ENERGY SYSTEMSNEW ENERGY SYSTEMS