Summit Deluxe PN 82058 Tripod Standimages.ebsco.com/pob/EbscoMedia/Catalog/82058-DELUXE... · 2015....
12
Summit Deluxe Tripod, 82058 - 3/12 • IT IS IMPORTANT TO NOTE THAT A FALL CAN OCCUR AT ANY TIME AFTER LEAVING THE GROUND. • ALWAYS MAINTAIN THREE POINTS OF CONTACT WHEN AND LEAN FORWARD AS YOU CLIMB THE LADDER SECTION OF THIS TRIPOD! • READ AND UNDERSTAND ALL OF THE MANUFACTURER’S WARNINGS AND INSTRUCTIONS AND USE ALL SAFETY DEVICES PROVIDED. CONTACT SUMMIT TREESTANDS FOR ANY QUESTIONS. FAILURE TO DO SO COULD RESULT IN INJURY OR DEATH! • A SIGNAL DEVICE SUCH A MOBILE PHONE, RADIO, WHISTLE, SIGNAL FLARE OR PERSONAL LOCATOR DEVICE (PLD) MUST BE ON YOUR PERSON AND READILY AVAILABLE AT ALL TIMES! ALWAYS INFORM SOMEONE OF YOUR HUNTING LOCATION, WHERE THE TRIPOD WILL BE LOCATED AND THE EXPECTED DURATION OF THE HUNT! • DO NOT USE THIS TRIPOD UNLESS YOU ARE IN GOOD PHYSICAL SHAPE AND HAVE NO PHYSICAL LIMITATIONS OR MEDICAL CONDITIONS WHICH MAY PREVENT YOU FROM SAFELY USING THIS PRODUCT. ALWAYS CONSULT A PHYSICIAN IF YOU HAVE ANY QUESTIONS ABOUT YOUR PHYSICAL ABILITY TO USE THIS PRODUCT. • NEVER USE THIS TRIPOD WHILE TAKING DRUGS, ALCOHOL OR CERTAIN PRESCRIPTION DRUGS! ALWAYS CONSULT A PHYSICIAN IF YOU HAVE ANY QUESTION ABOUT TAKING SPECIFIC MEDICATIONS AND USING THIS PRODUCT! • NEVER USE THIS TRIPOD DURING INCLEMENT WEATHER SUCH AS RAIN, LIGHTNING, WINDSTORMS OR ICY CONDITIONS! END YOUR HUNT AND RETURN TO THE GROUND IF ANY OF THESE INCLEMENTCONDITIONS ARISE. • NEVER USE THIS TRIPOD WHEN FEELING ILL, NAUSEOUS, DROWSY OR DIZZY! • BE WELL RESTED AND NEVER HURRY. HURRYING CAUSES ACCIDENTS! • CHECK EVERY COLUMN SECTION CONNECTION EVERY TIME YOU USE THE TRIPOD. IF ANY COLUMN SECTIONS ARE SEPARATING - DO NOT USE THE TRIPOD! • ALWAYS USE THE SUPPLIED SPIKES TO SECURE THIS TRIPOD TO THE GROUND BEFORE USE - EVEN IF IT IS TO BE USED WITHOUT A LEG EXTENSION KIT! • NEVER SETUP OR USE THIS TRIPOD AROUND POWER LINES, POWER TRANSFORMERS, SUBSTATIONS OR POWER GENERATORS! • CHECK THE GROUND UNDER THE TRIPOD TO MAKE SURE IT IS FIRM AND LEVEL. SLOPING GROUND OR AN UNEVEN SURFACE (ONE COLUMN SECTION ON A ROCK FOR EXAMPLE) CAN CAUSE YOUR TRIPOD TO TILT OR SHIFT AS YOU CLIMB. • PULL UP A BOW, BACKPACK, FIREARM OR OTHER EQUIPMENT ONLY AFTER BEING SECURE IN THE TRIPOD. FIREARMS MUST BE PULLED UP UNLOADED, CHAMBER OPEN AND MUZZLE DOWN! • NEVER MODIFY YOUR TRIPOD IN ANY WAY BY MAKING REPAIRS, REPLACING PARTS, OR ALTERING ADDING OR ATTACHING ANYTHING TO IT EXCEPT IF EXPLICITLY AUTHORIZED IN WRITING BY THE MANUFACTURER! • INSTRUCTIONS (WRITTEN AND VIDEO) SHOULD BE KEPT IN A SAFE PLACE AND REVIEWED AT LEAST ANNUALLY. IT IS THE RESPONSIBILITY OF THE TRIPOD OWNER TO FURNISH THE COMPLETE INSTRUCTIONS TO ANY PERSON WHO BORROWS OR PURCHASES THE TRIPOD! THIS SUMMIT TRIPOD IS DESIGNED TO BE USED AS A COMPLETE SYSTEM - NEVER LOAN OR SELL ONLY A PORTION OF THIS TRIPOD. • BEFORE EACH USE OF YOUR SUMMIT TRIPOD, ALWAYS INSPECT THE TRIPOD FOR ANY DAMAGE, CRACKS, TEARS, WEAR OR ABRASION THAT MAY HAVE OCCURRED IN TRANSPORTING / STORING YOUR TREESTAND. DO NOT USE IF ANY DAMAGE IS FOUND! CONTACT CUSTOMER SERVICE FOR THE APPROPRIATE REPAIR / REPLACEMENT PROCEDURE! • DO NOT LEAVE YOUR TRIPOD OUTDOORS WHEN IT IS NOT BEING USED! ANY STAND TUBING THAT IS ALLOWED TO FILL WITH RAINWATER AND FREEZE WILL RUPTURE OR BURST - DO NOT USE YOUR TRIPOD IF THIS OCCURS! • ALWAYS USE THREE PEOPLE TO SETUP THIS TRIPOD WARNING ! You must fully read, understand and follow these warnings and instructions (written and video)! Failure to follow these instructions may cause serious injury or death!! Summit Deluxe Tripod Stand PN 82058 © 2012 Summit Treestands, LLC 715 Summit Dr. Decatur, AL 35601 (256) 353-0634 [email protected] www.summitstands.com You MUST also view the enclosed DVD BEFORE using your new treestand!! WEIGHT LIMIT SINGLE USER 300 LBS. X 1 TOTAL* DO NOT EXCEED THIS LIMIT! (* Includes all gear) Stand minimum and maximum tree size: 8-20” diameter
Transcript of Summit Deluxe PN 82058 Tripod Standimages.ebsco.com/pob/EbscoMedia/Catalog/82058-DELUXE... · 2015....
Summit Deluxe Tripod, 82058 - 3/12
• ITISIMPORTANTTONOTETHATAFALLCANOCCURATANYTIMEAFTERLEAVINGTHEGROUND.
• ALWAYSMAINTAINTHREEPOINTSOFCONTACTWHENANDLEANFORWARDASYOUCLIMBTHELADDERSECTIONOFTHISTRIPOD!
• READANDUNDERSTANDALLOFTHEMANUFACTURER’SWARNINGSANDINSTRUCTIONSANDUSEALLSAFETYDEVICESPROVIDED.CONTACTSUMMITTREESTANDSFORANYQUESTIONS.FAILURETODOSOCOULDRESULTININJURYORDEATH!
• ASIGNALDEVICESUCHAMOBILEPHONE,RADIO,WHISTLE,SIGNALFLAREORPERSONALLOCATORDEVICE(PLD)MUSTBEONYOURPERSONANDREADILYAVAILABLEATALLTIMES!ALWAYSINFORMSOMEONEOFYOURHUNTINGLOCATION,WHERETHETRIPODWILLBELOCATEDANDTHEEXPECTEDDURATIONOFTHEHUNT!
• DONOTUSETHISTRIPODUNLESSYOUAREINGOODPHYSICALSHAPEANDHAVENOPHYSICALLIMITATIONSORMEDICALCONDITIONSWHICHMAYPREVENTYOUFROMSAFELYUSINGTHISPRODUCT.ALWAYSCONSULTAPHYSICIANIFYOUHAVEANYQUESTIONSABOUTYOURPHYSICALABILITYTOUSETHISPRODUCT.
• NEVERUSETHISTRIPODWHILETAKINGDRUGS,ALCOHOLORCERTAINPRESCRIPTIONDRUGS!ALWAYSCONSULTAPHYSICIANIFYOUHAVEANYQUESTIONABOUTTAKINGSPECIFICMEDICATIONSANDUSINGTHISPRODUCT!
• NEVERUSETHISTRIPODDURINGINCLEMENTWEATHERSUCHASRAIN,LIGHTNING,WINDSTORMSORICYCONDITIONS!ENDYOURHUNTANDRETURNTOTHEGROUNDIFANYOFTHESEINCLEMENTCONDITIONSARISE.
• NEVERUSETHISTRIPODWHENFEELINGILL,NAUSEOUS,DROWSYORDIZZY!
• BEWELLRESTEDANDNEVERHURRY.HURRYINGCAUSESACCIDENTS!
• CHECKEVERYCOLUMNSECTIONCONNECTIONEVERYTIMEYOUUSETHETRIPOD.IFANYCOLUMNSECTIONSARESEPARATING-DONOTUSETHETRIPOD!
• ALWAYSUSETHESUPPLIEDSPIKESTOSECURETHISTRIPODTOTHEGROUNDBEFOREUSE-EVENIFITISTOBEUSEDWITHOUTALEGEXTENSIONKIT!
• NEVERSETUPORUSETHISTRIPODAROUNDPOWERLINES,POWERTRANSFORMERS,SUBSTATIONSORPOWERGENERATORS!
• CHECKTHEGROUNDUNDERTHETRIPODTOMAKESUREITISFIRMANDLEVEL.SLOPINGGROUNDORANUNEVENSURFACE(ONECOLUMNSECTIONONAROCKFOREXAMPLE)CANCAUSEYOURTRIPODTOTILTORSHIFTASYOUCLIMB.
• PULLUPABOW,BACKPACK,FIREARMOROTHEREQUIPMENTONLYAFTERBEINGSECUREINTHETRIPOD.FIREARMSMUSTBEPULLEDUPUNLOADED,CHAMBEROPENANDMUZZLEDOWN!
• NEVERMODIFYYOURTRIPODINANYWAYBYMAKINGREPAIRS,REPLACINGPARTS,ORALTERINGADDINGORATTACHINGANYTHINGTOITEXCEPTIFEXPLICITLYAUTHORIZEDINWRITINGBYTHEMANUFACTURER!
• INSTRUCTIONS(WRITTENANDVIDEO)SHOULDBEKEPTINASAFEPLACEANDREVIEWEDATLEASTANNUALLY.ITISTHERESPONSIBILITYOFTHETRIPODOWNERTOFURNISHTHECOMPLETEINSTRUCTIONSTOANYPERSONWHOBORROWSORPURCHASESTHETRIPOD!THISSUMMITTRIPODISDESIGNEDTOBEUSEDASACOMPLETESYSTEM-NEVERLOANORSELLONLYAPORTIONOFTHISTRIPOD.
• BEFOREEACHUSEOFYOURSUMMITTRIPOD,ALWAYSINSPECTTHETRIPODFORANYDAMAGE,CRACKS,TEARS,WEARORABRASIONTHATMAYHAVEOCCURREDINTRANSPORTING/STORINGYOURTREESTAND.DONOTUSEIFANYDAMAGEISFOUND!CONTACTCUSTOMERSERVICEFORTHEAPPROPRIATEREPAIR/REPLACEMENTPROCEDURE!
• DONOTLEAVEYOURTRIPODOUTDOORSWHENITISNOTBEINGUSED!ANYSTANDTUBINGTHATISALLOWEDTOFILLWITHRAINWATERANDFREEZEWILLRUPTUREORBURST-DONOTUSEYOURTRIPODIFTHISOCCURS!
• ALWAYSUSETHREEPEOPLETOSETUPTHISTRIPOD
WARNING!You must fully read, understand and follow these warnings and instructions (written and video)! Failure to follow these instructions may cause serious injury or death!!
Summit DeluxeTripod Stand
PN 82058
© 2012 Summit Treestands, LLC715 Summit Dr. Decatur, AL 35601(256) [email protected]
YouMUSTalsoviewtheenclosedDVDBEFOREusingyournewtreestand!!
WEIGHT LIMITSINGLE USER
300 LBS. X 1 TOTAL*
DO NOT EXCEED THIS LIMIT!(* Includes all gear)
Stand minimum and maximum tree size: 8-20” diameter
1 INDEX
PG 2
GENERAL WARNINGS AND PRECAUTIONS, TRIPOD WEIGHT LIMITS PG 1SECTION 1 - INDEX PG 2SECTION 2 - PARTS LIST PG 2SECTION 3 - TOOLS REQUIRED PG 2SECTION 4 - ASSEMBLY PG 4-11SECTION 5 - SETUP AND USE PG 12SECTION 6 - MAINTENANCE AND CARE PG 12SECTION 8 - LIMITED WARRANTY INFORMATION PG 12
2 PARTS LIST
3 TOOLS REQUIRED
Pleasecall256-353-0634orvisithttp://www.summitstands.com/contactus/ifyouhaveanyquestions,ifyouneedreplacementparts,ifyouhaveanymissingpartsoriftheincludedDVDdoesnotplay.
www.summitstands.com
Tools Use• 7/16” Wrenches and / or Socket / Ratchet All Hardware, 1/4x20 threads• Knife or Snips Cable Tie Trimming
- Assembly can be made easier by the use of a powered ratchet or drill with socket adapter (take care not to overtighten when using power tools to assemble)- It is recommended that all bolts be sorted by thread count / length prior to assembly.
BOX CONTENTS
PN DESCRIPTION QTY 82058.210 PLATFORMASSEMBLY 382058.310 PLATFORMSUPPORTTUBE 382058.400 UPPERLEGASSEMBLY 282058.500 LOWERLADDERASSEMBLY 182058.610 LOWERCROSSBRACEA 382058.710 LOWERCROSSBRACEB 382058.810 UPPERCROSSBRACEA 382058.910 UPPERCROSSBRACEB 382058.1000 SHOOTINGRAILSUPPORTASSEMBLY282058.1110 SHOOTINGRAIL 382058.1200 SHOOTINGRAILSUPPORTTUBE 282058.1300 LOWERHUB 182058.1400 UPPERHUB 182058.1500 CROSSBRACECLAMP 1882058.2100 LOWERLEGASSEMBLY 282058.2200 UPPERLADDERASSEMBLY 182058.2310 SAFETYRAIL 382058.2410 32”ARMPAD 382058.2510 IN-LINECABLETIE 982058.2610 FOLDINGSEATBACK 182058.2710 FOLDINGSEATBASE 182058.2800 METALSEATBASE 182058.2900 SEATPOST 182058.3000 INSTRUCTIONALDVD 182058.3100 INSTRUCTIONBOOKLET 182058.3200 HARDWAREPACKET 1
82058.3200 - HARDWARE PACKET
PN DESCRIPTION QTY 10624 1”BOLT,1/4x20 25
10604 11/4”BOLT,1/4x20 6
10601 13/4”BOLT,1/4x20 18
10606 2”BOLT,1/4x20 5
10612 CENTERLOCKNUT,1/4x20 50
10625 1/4”Washer 4
PG 3
PLATFORM SUPPORT FRAME1. PositiontwoUpperLegAssembliesandonePlatformSupportTubeasshowninfigure 1.TheUpperLegAssembliesdonothaveaswagedend(as shown in figure 2).OnlytheLowerLegAssemblieshaveaswagedend.PleasenotethecorrectorientationoftheSupportTubeasshowninfigure 3.2. SlidetheSupportTubeovertheendsoftheLegAssembliesasshowninfigure 3.
PLATFORM SUPPORT TUBE(PN 82058.310)
1
4 ASSEMBLY
UPPER LEG ASSEMBLY(PN 82058.400)
2
3
NO SWAGE
3. PositiontheUpperLadderAssemblyandanotherPlatformSupportTubeasshowninfigure 4. 4.SlidetheSupportTubeovertheendoftheLegAssemblyandtheendoftheLadderAssembly.TheUpperLadderAssemblydoesnothaveaswagedend.5. SlidetheremainingPlatformSupportTubeovertheendoftheLegAssemblyandLadderAssembly(see figure 5).
UPPER LADDER ASSEMBLY(PN 82058.2200)
PLATFORM SUPPORT TUBE(PN 82058.310)
4
5
PLATFORM SUPPORT TUBE(PN 82058.310)
UPPER LADDER ASSEMBLY
UPPER LEG ASSEMBLY
UPPER LEG ASSEMBLY
www.summitstands.com
BENT TOWARD CENTER OF PLATFORM
PG 4 www.summitstands.com
PLATFORM1. PositiononeofthePlatformAssembliesasshowninfigure 6.ThefourweldedonbracketswillfitoverthePlatformSupportTubes.2. SlidethePlatformAssemblydownontotheSupportTubesasshowninfigure 7.
6
PLATFORM ASSEMBLY(PN 82058.210)
7
3. PositiontheothertwoPlatformAssembliesasshowninfigure 8. SlidethesedownontotheSupporttubesandbuttthemupascloseaspossibletoeachother.Thesixweldedontabs(inblue)underthePlatformAssembliesshouldlineupasshowninfigure 9.
8 PLATFORM ASSEMBLY(PN 82058.210)
9
4. Useone1” bolt and lock nuttosecureeachplatformsectiontogether(see figure 10.)Alternatetighteningofthesethreeboltsuntiltheplatformsectionshavebeenpulledtogether.Thereshouldnotbeanygapsbetweenthebracketsoncetight.
1” BOLTS, LOCK NUTS - WRENCH TIGHTEN
10
PG 5
5. Usetwelve(12),1 3/4” bolts with lock nutstosecuretheplatformUbracestotheSupportTubesasshowninfigure 11.Seefigure 12forboltlocations.Wrenchtightenallbolts.
12 1 3/4” BOLTS, LOCK NUTS - WRENCH TIGHTEN
11
UPPER CROSS BRACES1. Next,assembletheUpperCrossBraces.SlidetheUpperCrossBraceAintotheopenendoftheUpperCrossBraceBasshowninfigure 13.BraceAhasanoveralllengthof35.6”whileBraceBhasanoveralllengthof37.6”.2. Useone1 1/4” bolt and lock nuttosecurethetwoBraceSectionstogetherasshowninfigure 14. 3. Repeat for the other five Upper Cross Braces.
UPPER CROSS BRACE B(PN 82058.910)
UPPER CROSS BRACE A(PN 82058.810)
1 1/4” BOLTS, LOCK NUTS - WRENCH TIGHTEN
14
13
4. SnaponeoftheCrossBraceClampsontothelegtubingasshowninfigure 15.TheClampscanbespreadaparttofitoverthetubing.5. OncetheClamphasbeenattached,pinchtheopenendstogether.6. PositiononeofthecompletedUpperCrossBraces(inblue)asshowninfigure 17.ThisbracewillrundiagonallybetweentwoClamps(ingreen).7. TheendsoftheCrossBraceshouldfitbetweentheopenendsoftheClamp(see figure 16.)8. Useone,1” bolt and lock nuttosecuretheCrossBracetotheupperClamp.Leavethisconnectionhandtightfornow.
CROSS BRACE CLAMP(PN 82058.1500)
15
16
17CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE
1” BOLT, LOCK NUT
PG 6 www.summitstands.com
9. SlidetheUpperClamptightagainstthecrossrungasshowninfigure 18.Wrenchtightentheupperbolt.10. Useanother1”bolt and lock nuttosecuretheCrossBracetothelowerClamp.11. AttachanotherUpperCrossBracenext.PositionitinthesamelocationasthefirstBrace.Snaptwoclampsontothetubingasshowninfigure 19. RuntheCrossbracebetweenbothclamps.12. Useone1” bolt and lock nutateachclamptosecurethebrace.
18
19CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE
1” BOLTS, LOCK NUTS
13. AttachthefinalUpperCrossBracenow.PositionitinthesamelocationasthefirsttwoBraces.Snaptwoclampsontothetubingasshowninfigure 20. RuntheCrossbracebetweenbothclamps.14. Useone1” bolt and lock nutateachclamptosecurethebrace.15. AllthreeBracesshouldrunfromthetoplefttothelowerrightasshowninfigure 20.
20CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE
HUB ASSEMBLY1. PositiontheUpperHubabovethecenteroftheplatformasshowninfigure 21.Insertthree2” boltsthroughthehubfromabove.2. Fromundertheplatform,lineuptheboltholesinthelowerhubandslideitovertheboltsasshowninfigure 22.3. Securethehubstogetherusingthreelock nutsasshowninfigure 23.
UPPER HUB(PN 82058.1400)
2” BOLTS
LOWER HUB(PN 82058.1300)
21
22 23
LOCK NUTS
PG 7
SHOOTING RAIL ASSEMBLY1. PositiononeoftheShootingRailSupportAssembliesasshowninfigure 24.ThisRailSupportwillattachaboveoneoftheLegAssembliesasshown(notabovetheladderassembly).2. SlidetheRailSupportdownoverthetubingbutdonotbolttogetheryet.3. PositiontheotherShootingRailSupportasshowninfigure 25.ItwillattachabovetheotherLegAssemblyasshown.SlidetheRailSupportdownoverthetubingbutdonotbolttogetheryet.
SHOOTING RAIL SUPPORT ASSEMBLY(PN 82058.1000)
24
LEG ASSEMBLY
SHOOTING RAIL SUPPORT ASSEMBLY(PN 82058.1000)
LEGASSEMBLY
25
4. PositiononeoftheShootingRailsasshowninfigure 26. ThisrailwillslidedownovertheendsoftheShootingRailSupports.5. SlideoneoftheShootingRailSupportTubesovertheframeasshowninfigure 27. Donotbolttogetheryet.6. SlidetheotherShootingRailSupportTubeovertheoppositesideasshowninfigure 28.
SHOOTING RAIL (PN 82058.1110)
26
27 28
LADDERASSEMBLY
LADDERASSEMBLY
SHOOTING RAILSUPPORT TUBE(PN 82058.1200)
SHOOTING RAILSUPPORT TUBE(PN 82058.1200)
PG 8 www.summitstands.com
SHOOTING RAIL ASSEMBLY (continued)7. PositiontheremainingtwoShootingRailsasshowninfigure 29.SlidethesedownovertheendsoftheSupportTubesasshowninfigure 30.8. Useone1 3/4” bolt and lock nut(figure 31)tosecurethelowerbracketoneachofthesixShootingRailSupportsfromthestepslistedabove.Wrenchtightenallbolts.
SHOOTING RAIL (PN 82058.1110)
29
30
31
1 3/4” BOLTS, LOCK NUTS - WRENCH TIGHTEN
SAFETY RAIL ASSEMBLY1. AttachtwomoreCrossBraceClampstotheShootingRailSupportsasshowninfigure 32.2. RunoneoftheSafetyRailsbetweentheClampsandsecureusinga1” bolt and lock nutateachClampasshowninfigure 33. The Safety Rails should be positioned so that they are 17” up from the platform.
SAFETY RAIL (PN 82058.2310)CROSS
BRACE CLAMP(PN 82058.1500)
CROSSBRACE CLAMP(PN 82058.1500)
32
33
1” BOLTS, LOCK NUTS - WRENCH TIGHTEN
3. AttachtwomoreCrossBraceClampstotheShootingRailSupportsasshowninfigure 34. RunoneoftheSafetyRailsbetweentheClampsandsecureusinga1” bolt and lock nut ateachClamp.4. RepeatforthelastSafetyRailasshowninfigure 35.
34 35
1” BOLTS, LOCK NUTS - WRENCH TIGHTEN
1” BOLTS, LOCK NUTS - WRENCH TIGHTEN
PG 9
LOWER LEG ASSEMBLY1. Useahelperandcarefullylaythetripodonitsside.
2. Slidetheswagedend(see figure 36)oftheLowerLadderAssemblyintotheUpperLadderAssemblyasshowninfigure 37.
3. SlidetheswagedendofoneoftheLowerLegAssembliesintotheUpperLegAssembly(figure 38).
4. SlidetheswagedendoftheremainingLowerLegAssemblyintotheUpperLegAssemblyasshowninfigure 39.
! CAUTIONBraceattachmentmustbecompletedBEFOREattemptingtostandtheTripodup.
LOWER LADDER ASSEMBLY(PN 82058.500)
SWAGED END
36
37
38
39
LOWER LEGASSEMBLY(PN 82058.2100)
LOWER LEGASSEMBLY(PN 82058.2100)
LOWER CROSS BRACE B(PN 82058.710)
LOWER CROSS BRACE A(PN 82058.610)
1 1/4” BOLTS, LOCK NUTS - WRENCH TIGHTEN
40
PG 10 www.summitstands.com
LOWER CROSS BRACES1. Next,assembletheLowerCrossBraces.SlidetheLowerCrossBraceAintotheopenendoftheLowerCrossBraceBasshowninfigure 40.2. Useone1 1/4” bolt and lock nuttosecurethetwoBraceSectionstogetherasshowninfigure 41. 3. Repeat for the other five Lower Cross Braces.
4. SnaponeoftheCrossBraceClampsontothelegtubingasshowninfigure 42.5. PositiononeofthecompletedLowerCrossBraces(inblue)asshowninfigure 42.ThisbracewillrundiagonallybetweentwoClamps(ingreen).6. Useone,1” bolt and lock nuttosecuretheCrossBracetotheupperClamp.Leavethisconnectionhandtightfornow.7. SlidetheUpperClamptightagainstthecrossrungasshowninfigure 43.Wrenchtightentheupperbolt.8. Useanother1”bolt and lock nuttosecuretheCrossBracetothelowerClamp.ThelowerClampshouldbepositionedbetween3”-4”fromthelowercrossrungasshowninfigure 44.9. CarefullyrotatethestandandattachanotherLowerCrossBracenext.PositionitinthesamelocationasthefirstBrace.Snaptwoclampsontothetubingasshowninfigure 45. RuntheCrossbracebetweenbothclamps.10. Useone1” bolt and lock nutateachclamptosecurethebrace.11. CarefullyrotatethestandandattachthefinalLowerCrossBracenow.PositionitinthesamelocationasthefirsttwoBraces.Snaptwoclampsontothetubingasshowninfigure 46. RuntheCrossbracebetweenbothclamps.12. Useone1” bolt and lock nutateachclamptosecurethebrace.13. AllthreeBracesshouldrunfromthetoprighttothelowerleftasshowninfigure 47.
41
42
CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE
3” - 4” GAP
43 44
CROSS BRACE CLAMP(PN 82058.1500)
CROSS BRACE
1” BOLTS, LOCK NUTS
1” BOLTS, LOCK NUTS
45
1” BOLT
1/4” WASHER
METAL SEAT BASE(PN 82058.2800)
50
PG 11
46
1” BOLTS, LOCK NUTS
CROSS BRACE
CROSS BRACE CLAMP(PN 82058.1500)
47
SEAT ASSEMBLY1.LineuptheSeatBackrestwiththeSeatBaseasshowninfigure 48.(seatmaydifferinappearance)2. Usetwo,2”boltsandlocknutstosecuretheSeatBackresttotheSeatBaseasshowninfigure 49.Runtheseboltsfromtheinsideoutanddonotovertightenasthisconnectionisdesignedtopivot.3. PositiontheassembledSeatabovetheMetalSeatBaseasshowninfigure 50.BolttheSeattotheSwivelusingfour,1”boltsandwashers.4. SlidetheendoftheMetalSeatBaseintotheSeatPost.TheSeatPostslidesintothecenterhubontheplatformasshowninfigure 51.Theseatcanberemovedforstorage.
SEAT BACKREST(PN 82058.2610)
48
SEAT BASE(PN 82058.2710) 2” BOLT, LOCK NUT -
DO NOT OVERTIGHTEN
49
51
SEAT POST(PN 82058.2900)
SHOOTING RAIL PAD ASSEMBLY1. Positionthethree32”Padsasshowninfigure 52. 2. SecureeachpadwiththreeIn-Linecablestiesasshown.PleasenotetheCorrectandIncorrectwaysofusingtheties.Useasharpknifeorsnipstotrimtheexcess.Rotatetheclaspunderthepadwhentheyhavebeentrimmed.
Correct
Incorrect
52
IN-LINE CABLE TIE(PN 82058.2510)
32” PAD(PN 82058.2410)
32” PAD(PN 82058.2410)
32” PAD(PN 82058.2410)
(A)WarrantySummitTreestands,LLC(Summit)warrantstotheoriginalretailpurchaserthatallproductsmanufacturedbyitarefreefromdefectsinmaterialandmanufactureatthetimeofshipmentforsixty(60)monthsfromthedateofpurchase.SummitwillrepairorreplaceanypartfounddefectiveiftheunitclaimedtobedefectiveshallbereturnedtoSummit,postageprepaid,withinthewarrantyperiod.
Thiswarrantyshallnotapplytoanyproductwhichhasbeensubjectedtomisuse;misapplication;neglect(includingbutnotlimitedtoimpropermaintenance);accident;improperinstallation;modification(includingbutnotlimitedtouseofunauthorizedpartsorattachments);adjustmentorrepair.THEFOREGOINGISINLIEUOFALLOTHERWARRANTIES,WHETHEREXPRESSORIMPLIED(INCLUDINGTHOSEOFMERCHANTABILITYANDFITNESSOFANYPRODUCTFORAPARTICULARPURPOSE),ANDOFANYOTHEROBLIGATIONOFLIABILITYONTHEPARTOFTHECOMPANY.
(B)LimitationofLiabilityItisexpresslyunderstoodthatSummit’sliabilityforitsproducts,whetherduetobreachofwarranty,negligence,strictliability,orotherwise,islimitedtotherepairoftheproduct,asstatedabove,andSummitwillnotbeliableforanyotherinjury,loss,damage,orexpense,whetherdirectorconsequential,includingbutnotlimitedtolossofuse,income,profit,ordamagetomaterial,arisinginconnectionwiththesale,installation,useof,inabilitytouse,ortherepairorreplacementofSummit’sproducts.
Summitreservestherighttomakealterationsormodificationsinitsproductsatanytime,whichinitsopinion,mayimprovetheperformanceandefficiencyoftheproduct.Itshallnotbeobligatedtomakesuchalterationsormodificationstoproductsalreadyinservice.
Please take the time to fill out the warranty card online at http://www.summitstands.com/warranty or fill out and mail in theenclosed warranty card.
7 LIMITED WARRANTY
Theseatonthisladderstandisremovable.Werecommenditberemovedandstoredinadryplacewhennotinuse.
Thepowdercoatfinishappliedatthefactoryisverydurableandshouldonlyneedtouchupsinareasofheavywearoraccidentalimpact.Thepowdercoatisappliedonlytotheexteriorsurfacesofthetreestandsoitispossibleforsomesurfacerusttoforminsidethestandtubing.Thisisnormalandshouldnotaffectthedurabilityorperformanceofthestand.
ShouldyoudamageanypartofyourSummitTreestand,contactyournearestauthorizedSummitdealerorthefactorytoobtainthepropercorrectiveactionprocedureand/orreplacementpartsforthetreestand.
Lookfornicks,gouges,cuts,cracks,bends,corrosionorsimilardamagethatcanbetheresultofimproperuseoraccidentaldamage.Forinstance,thiscouldoccurifsomeoneelseusedthetreestandwithoutknowledgeofitsproperuse,orifthetreestandweredropped,hitbyamotorvehicleorsubjecttocorrosiveconditions,etc.
SummitTreestandshavethehigheststructuralintegritybydesign,materialselectionandmanufacturingtechniques,butasitsowner,onlyyourcontinuedcarewillassuretroublefreeperformance.Whentheabove-mentionedguidelinesarefollowed,yourSummitTreestandwillprovideyearsofsuccessfulhunting.
6 MAINTENANCE AND CARE
! CAUTION
5 SETUP AND USE
WARNING!Alwaysmaintainthreepointsofcontactwhenclimbingtheladderportionofthistripodstand.
WARNING!Duetothelargesizeandweightofthisproduct,itismandatorythataminimumofTHREEpeopleinitiallyhelpsetupthistripod.
1. FindasuitableareatosetuptheTripod.Checkthegroundunderthetripodtomakesureitisfirmandlevel.Slopinggroundoranunevensurface(onelegsectiononarockforexample)cancauseyourtripodtotiltorshiftasyouclimb.2. Tiltthestanduprightbywalkingthelegsuprightfromtheplatformdowntotheendofthelegs.Haveathirdpersonsecurethetoplegonceitislowenoughtoreach.NOTE: Thestandwillbeplatform/topheavy.
