Submittal Guide EST3edwards-es.com/Submittal Guides and Brochures/E85010-0099...Notification...
62
Notification Appliances Hazardous Location Devices Door Holders & Relays Initiating Devices EST3 Network EST3 S e e w h a t ' s p o s s i b l e n o w . . . Submittal Guide EST3 Emergency Communications Platform Life Safety and Incident Management Solutions LIFE SAFETY & INCIDENT MANAGEMENT S e e w h a t ’ s p o s s i b le n o w .
Transcript of Submittal Guide EST3edwards-es.com/Submittal Guides and Brochures/E85010-0099...Notification...
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwork
ES
T3
Se e w h a t ' s p o s s i b l e n o w . . .
Submittal Guide
EST3 Emergency Communications Platform
Life Safety and Incident Management Solutions
L I F E S A F E T Y & I N C I D E N T M A N A G E M E N T
See what’s possible now.
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwork
Project: ___________________________
Contact: ___________________________
Date: ___________________________
Thank you for giving us the opportunity to provide this submittal for an
EST3 Life Safety Control Platform. EST3 represents some of the most
technologically advanced innovations the life safety industry has ever seen –
innovations that will make your building and its occupants safe and secure.
This guide provides a summary of these innovations and includes a
presentation of related system components and devices. Products we
are submitting for your consideration are indicated by a checkmark in the
margins of the pages that follow.
More detailed information can be found in individual data sheets dedicated
to each product. All these sheets, along with guide specifications and other
useful product information, are available electronically on our LifeLines CD-
ROM. This collection of life safety related literature is fully searchable and
includes a utility for printing multiple data sheets.
Thank you for giving us the opportunity to provide this submittal. Please do
not hesitate to contact us should you require further information.
_____________________________
L I F E S A F E T Y & I N C I D E N T M A N A G E M E N T
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwork
iii
Submittal Guide
EST3 Emergency Communications Platform
Life Safety and Incident Management Solutions
EST3 Submittal Guide Intelligent control for large and medium sized applications
© 2018 United Technologies Corporation. All rights reserved. EDWARDS is a registered mark in the United States and other countries.
1016 Corporate Park Drive, Mebane, NC 27302
85010-0099
Wiring diagrams provided herein are for information and reference only and are not to be used for installation pur-poses. Consult the appropriate installation documents for wiring and configuration details.
This guidebook is for information only and is not intended as a substitute for verbatim legislated requirements. For authoritative specifications regarding the application of life safety, security, and access control systems, consult
current editions of applicable codes and standards. For authoritative interpretation of those codes and standards, consult your local authority having jurisdiction.
While every effort has been made to ensure the accuracy and completeness of this guidebook, the authors and publishers assume no responsibility for errors, inaccuracies, omissions, or any inconsistencies herein.
EST, Genesis Series, and Signature Series are trademarks of United Technologies Corporation.
v
EST3 Emergency Communications Platform
A lot can be said about EST3, but when it comes
to performance, price, installation ease and flex-
ibility, this remarkable life safety system speaks for
itself.
For example, a glance at the contents on
this page reveals just how few components are
needed to configure even the most sophisticated
and elaborate life safety, security, and access
control network. EST3’s modular design means
you only get the features you need, and its simple
configuration ensures trouble-free installation every
time.
And when it comes to connected devices,
nothing beats EST3. In fact, the Signature Series
line of intelligent analog detectors has been singled
out by Underwriters Laboratories as the first such
devices on the market that do not require a calibra-
tion sensitivity test in order to comply with NFPA72.
Quality and reliability are built into every
EST3 component, from the simplest control switch
to the system’s main processor. And that’s not just
a corporate mandate: it’s a proven fact supported
by our commitment to ISO 9000 international qual-
ity standards. EST3 is certified under ISO, not only
for manufacturing, but for design, training, custom-
er service, and technical support as well. This en-
sures that your EST3 network will provide extremely
reliable service the day it’s brought on-line and well
into the future.
EST3: Innovation geared to your needs.
No
tific
atio
n A
pp
liancesH
aza
rdo
us L
oc
atio
n D
evicesD
oo
r Ho
lders
& R
elaysIn
itiatin
g
Devices
ES
T3
Netw
ork
Intelligent Analog Initiating Devices 21CO, Smoke and Heat Detectors ..................................... 22Fire Detectors ................................................................. 23Duct Detectors ............................................................... 23Detector Bases .............................................................. 24Detector Accessories ..................................................... 25Input/Output Modules .................................................... 26Pull Stations ................................................................... 32
Notification Appliances 33Wall Strobes, Horns & Chimes ........................................ 35Low Frequency Horns and Horn-Strobes ....................... 36Ceiling Horns & Horn-Strobes ........................................ 36Outdoor Horns & Strobes ............................................... 37Wall Speakers & Speaker-Strobes .................................. 38Ceiling Speakers, Horns & Strobes ................................. 39Outdoor Speakers & Strobes .......................................... 40High Power Speaker Arrays ............................................ 41LED Strobes and Horn-Strobes ...................................... 41Medium Power Speaker Arrays ...................................... 42Firefighters’ Telephones .................................................. 43Harsh Environment Signals ............................................. 44Audible Signals ............................................................... 45Accessories .................................................................... 46
Hazardous Location Devices 48Initiating Devices............................................................. 48Notification Appliances ................................................... 49
Door Holders & Relays 50Door Holders .................................................................. 50Relays ............................................................................ 50SPDT Relays .................................................................. 51
EST3 Network 1Network Control ............................................................... 2Local Rail Modules ........................................................... 4Control, Display, and Annunciation ................................... 8Mass Notification ............................................................ 12Network Audio ............................................................... 14Power Supplies .............................................................. 16Security .......................................................................... 18Network Accessories...................................................... 19Cabinets & Chassis ........................................................ 20
D e t e c t i o n & A l a r m S i n c e 1 8 7 2 .
See what’s possible now.
Mass Notification • Smoke Detection • Graphical Monitoring and Control • Instant Messaging • Aspirating Smoke Detectors • Industrial Signaling • Voice Evacuation • Smoke Control • Fire Suppression • Intercom • Timekeeping • CO Detection • Heat Detection • Audible & Visible Signaling • Voicemail Messaging • Duct Smoke Detection • Giant Voice • Electronic Signage • Area of Rescue
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
1
EST3 N e t w o r k
EST3 is a modular system uniquely designed to easily meet the needs of standalone single node systems or multi-node networks. Fire alarm, security, and audio functions use the same fundamental components, simplifying system layouts. A powerful System Definition Utility program helps define sys-tem operations in a fraction of the time required by previous methods. Virtually all EST3 operating features are software controlled. This gives EST3 great site flexibility and ensures operational changes and upgrades will be possible years after the initial installation.
Highly Flexible ApplicationsEST3 is a superbly adaptable life safety system, lending itself to medium and large building applications. Cabinets are available with room for system batteries up to 65 Amp hours. With EST3, one 24-volt battery supports up to four power sup-plies. Each supply will support up to 7 Amp load. With four supplies, 28 Amps of current is available — all backed up by a common battery.
Fully-listed User InterfacesThe user interface layer is made up of a Liquid Crystal Display module and a system of generic modules designed to maximize design flexibility for custom systems.
In addition to front panel control and annunciation, EST3’s powerful FireWorks color graphics package provides desktop control and messaging in the familiar Windows environment. Fireworks’ unique four-quadrant display gives the user access to all EST3 functions including fire alarm, security, and CCTV – in one simple and intuitive interface. And because FireWorks is an integral part of the EST3 network, it is listed by UL not only under fire alarm standards, but under local burglar, and proprietary monitoring standards as well.
Powerful NetworkingEST3 operates on a multi priority peer-to-peer network. The multi-priority token ring gives EST3 exceptional response. Response time for all functions, including fire and security, is less than three seconds across the network regardless of the total number of nodes. EST3 token ring network configura-tion also permits vast distances between nodes. The allow-able distance between three nodes on #18AWG (0.75mm2) is 5,000ft (1,523m). With 64 nodes supported on a network, the total network length is in excess of 300,000 ft (91,400m), or nearly 60 miles! A single node supports up to 10 Signature loop controllers with 250 devices per loop, (2,500 points total
per node).
EST3 also makes field wiring easy with building wiring ter-minations that use removable terminal blocks on local rail modules.
Eight-channel AudioEST3 audio design provides the emergency user with a communication package that minimizes switch selections.
This facilitates simple, accurate and fast evacuation control announcements. EST3 provides simple paging controls. Pressing All Call selects all paging zones for message delivery. Pressing Page To Evacuation automatically selects all areas in evacuation. Similarly, the user can Page To Alert. Zoned pag-ing requires the user to simply select zone paging switches.
Taking full advantage of digital technology, up to eight chan-nels of audio sources can be sent over a single twisted pair of wires between nodes. Coupling the inherent reliability and performance of zoned amplifiers with EST3 simplified user in-terfaces makes audio system design and operation both easy and dependable.
EST3 is the right choice for any medium to large application. Its multiplex functions are second to none in the industry today.
Network Control p. 2
Local Rail Modules p. 4
Control, Display, and Annunciation p. 8
Mass Notification p. 12
Network Audio p. 14
Power Supplies p. 16
Security p. 18
Network Accessories p. 19
Cabinets & Chassis p. 20EST3 Network
BOX
LOCALRAIL
MODULESCHASSIS
CONTROLDISPLAY
MODULES
INNERDOORCOVER
OUTERDOOR
System components arrange in layers starting with the wallbox system and ending with inner and outer doors.
EST3 N e t w o r k
2
ES
T3
N
etw
ork
DEDICATED FIBER OPTIC
CCS PANEL
TCP/IP
TO
RS-232
FIREWORKS
TCP/IP
TO
RS-232
ACU/FACP
TCP/IP
Audio to VoIP
Interface
VoIP to Audio
Interface
DEDICATED
FIBER OPTIC
VoIP VoIP
DIGITAL AUDIO DIGITAL AUDIO
EST3 NETWORK DATA
LOC
EST3 NETWORK
DATA
ANALOG AUDIO
EST3 NETWORK DATA
LOC
EST3 NETWORK
DATA
ANALOG AUDIO
20 ft, max.
Application: Multiple EST3 Net-works with Fireworks on Dedi-cated UL2572 Listed IP Network using IP & VOIP communications
Fire alarm and mass notification: no matter what the configuration, EST3 provides a total life safety system. With fire alarm providing the communications backbone, EST3 is UL2572 Listed for mass notifica-tion operations, while retaining its UL864 listing as a fire alarm control system. This unique standing ensures that mass notification functions are in perfect harmony with other life safety operations.
EST3 ensures that mass notification retains priority over fire alarm events and that mass motification will not affect the network response speed of fire reporting mandated by codes and standards.
The benefits of this method are many. Mass notification now benefits from the survivability and reliability mandated by the fire codes and life safety standards. Costs are reduced because system resources are shared. Installation of a single unified system is vastly more efficient than installing multiple interconnected systems. There is no finger pointing, patchwork protocols or gateways that combine one system with another. Just the simple elegance of a single system unencum-bered by needless redundancy. EST3 achieves true operational unity with single-system responsibility.
See Page 12 for mass notification equipment.
Mass NotificationUL 2572 Listed Mass Notification and UL 864 Listed Fire Alarm
EST3 N e t w o r k
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
3
Central Processor Unit
The central processor unit is the heart of the EST3 network node. As a single node standalone system, a single 3-CPU3 controls up to 19 local rail modules. For larger systems, up to 64 nodes intercon-nect on a peer-to-peer multi-priority token ring protocol network.
The central proces-sor unit controls a l l loca l pane l r e s p o n s e s t o automatic, user initiated, or net-work reported events. As a network node, it is an equal among peers: there is no master on the network. Multi-priority token ring means that a node with a new alarm has priority on the network. This gives exceptional response times over the network — less than three seconds.
Each central processor unit provides connectors for mounting network, RS-232, and memory expansion cards. Removable terminal blocks on the central processor unit support connection of network and audio data wiring. On-board common relays also terminate at the central processor unit terminals. To aid in troubleshooting and service, status LEDs monitor local rail, network, RS232 and audio data communications.
3-CPU3 Central Processor Unit Module Data Sheet E85010-0133
Network Communication CardThe Network Communications card mounts to the back of the Central Processor Unit. The 3-RS485A card provides a Class A or Class B circuit for network communications signals and two additional circuits for Class A digitized audio signals. The 3-RS485B card provides a Class B circuit for network communications signals and a second Class B circuit for the digitized audio signals. Network messages received by the Network Communications card are re-transmitted to the next network node.
3-RS485A Network Communications Card, Class A or Class X. Data Sheet E85010-0133
3-RS485B One Class A,X/B network data circuit and one Class B audio data circuit. Data Sheet E85010-0133
RS-232 Communication CardThe 3-RS232 Communication Card mounts to the back of the 3-CPU3. The 3-RS232 has two optically-isolated RS-232 ports. The ports support connection of a printer and/or an external command center.
3-RS232 RS-232 Communication Card Data Sheet E85010-0133
PowerSupply
PowerSupply
J8
J9
J10
J11
J8
J9
J10
J11
CentralProcessor
UnitModule3-CPU
LRM
LRM
LRM
LRM
LRM
3-CHAS7
Central ProcessingUnit Module
1 2 43 5 6 7 8 9 10
N.C
.T
RO
UB
LE
CO
M.T
RO
UB
LE
N.O
.T
RO
UB
LE
N.O
.A
LA
RM
CO
MA
LA
RM
N.C
.A
LA
RM
N.O
.S
UP
V.
CO
MS
UP
V.
N.C
.S
UP
V.
SY
ST
EM
TR
OU
BL
ER
EL
AY
(sh
ow
nin
no
rma
ls
tate
)
SY
ST
EM
SU
PE
RV
ISO
RY
RE
LA
Y
COMMON SYSTEM RELAYS
SY
ST
EM
AL
AR
MR
EL
AY
11 112 214 413 315 516 617 718 819 920 10
OR
Ne
two
rkD
ata
Ris
er
Network Audio Riser
Class A only
Cla
ss
Ao
nly
Ne
two
rkA
ud
ioR
ise
r
To
/Fro
mp
revio
us
pa
ne
lo
ra
3-A
SU
3-C
PU
(1)(
3)
To
pre
vio
us
pa
ne
lM
od
ule
or
a3
-AS
U3
-CP
U(1
)(3
)
To
/Fro
mn
ext
pa
ne
lM
od
ule
3-C
PU
(1)(
3)
Fro
mn
ext
pa
ne
l3
-CP
U(1
)(3
)M
od
ule
PIN 1
PIN 14
PIN 13 PIN 25
PIN 1
PIN 9
(2) TXD
(2) RXD
Connect to TB1 on 3-CPU3 Module
Connect to TB2 on 3-CPU3 Module
(3) RXD
(3) TXD
(7) COM
(5) COM
DB25 FEMALE(REAR VIEW)
DB9 FEMALE(REAR VIEW)
PL
UG
PIN
#
PIN
FU
NC
TIO
N
TO PRINTER OR REMOTECOMMAND SYSTEM,
TO PRINTER OR REMOTECOMMAND SYSTEM,
ISOLATED PORTTO PRINTER OR REMOTECOMMAND SYSTEM.
PORT #2(isolated)
PORT #2(isolated)
PORT #1
PIN 1
PIN 14
PIN 13 PIN 25
(2) TXD
(3) RXD
(7) COM
DB25 FEMALE(REAR VIEW)
3-CPU3
ES
T3
N
etw
ork
4
EST3 N e t w o r k
SUBMIT
Local Rail Modules
Local Rail Modules (LRMs) conveniently mount to the EST3 inner chassis, away from high voltages. Each module features removable terminal blocks and simple plug-in
connectors. LRMs include Zoned Amplifiers, Signature Loop Controllers, Conventional Hardwired Modules, Off Premise Signaling Modules, as well as the main CPU module.
Control Display Modules can be mounted on any LRM.Local RailModule
RemovableTerminal Blocks
Local Rail
Signature Driver Controller Modules
The 3-SSDC1 and 3-SDDC1 Signature Driver Controller modules provide an intelligent interface between the 3-CPU(1.3) module and Signature Series devices. Each module contains its own microprocessor used to coordinate, process and interpret information received from and sent to Signature de-vices. Power and communications is received directly from the control panel rail assembly. The 3-SSDC1 Single Signature Driver Controller module sup-ports one Signature Data circuit, while the 3-SDDC1 Signature Dual Driver Controller module supports two Signature circuits. Both modules occupy one rail space in the fire alarm control cabinet and provide removable field wiring terminals to aid installation.
Innovative design gives the 3-SSDC1/3-SDDC1 and Signature devices truly “distributed intelligence”. Signature detectors and modules have their own on-board microprocessor communicating with the loop controller in a fully digital communication format. This increases the accuracy of the information coming to and from the loop controller by reducing the effects of capacitance and noise.
With decentralized intelligence much of the decision making moves from the loop controller to the devices. Advanced fire detection algorithms processed within the Signature devices effectively end unwanted alarms. Environmental compensation and multiple sensing element decision making operations are resident in the devices. Intelligent devices allow the Signature Controllers to execute communication and system functions with greater speed and low baud rates, increasing the accuracy of information transmitted between the loop controller and devices.
To enhance survivability of the system the 3-SSDC1/3-SDDC1 supports a standalone mode for Signature devices. Two catastrophic failure modes are supported. If the 3-CPU(1/3) fails, the loop controller will continue to poll its devices. If an alarm is detected it will be sent on the local rail communication bus and received by other local rail modules. A common alarm condition throughout the panel will result. If the local rail module (3-SSDC1/3-SDDC1) fails, and a device (smoke or module) detects an alarm, specialized circuitry will make the node aware of the alarm condition. The 3-CPU(1/3) will com-municate the alarm condition to the rest of the network. Having multiple redundant modes is paramount in a life safety system.
3-SSDC1 Single Signature Driver Controller, c/w one 3-SDC1 Data Sheet E85010-0129
3-SDDC1 Dual Signature Driver Controller, c/w two 3-SDC1s Data Sheet E85010-0129
3-SDC1 Signature Device Card - upgrades a 3-SSDC1 to a 3-SDDC1 Data Sheet E85010-0129
TB1
3-SDDC1SIGNATURE
DRIVERCONTROLLER
MODULE
DUAL
TB2
Class A Configuration Shown (Typical)
Class A Configuration Shown (Typical)
Circuit #1
To TB1 on 3-SDDC1 Module
SDC #1 SmokePower
1 2 43 5 6 7 8 9 10
++
Circuit #2
To TB2 on 3-SDDC1 Module
SDC #2 SmokePower
1 2 43 5 6 7 8 9 10
+ +
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
5
EST3 N e t w o r k
SUBMIT
EOL
Connect to IDC/NAC 1, 2, 7, or 8NOTIFICATION APPLIANCE CIRCUIT (NAC)
+ +- -
+ +- -
+ +- -
EOL
Detector Base
Connect to IDC 3, 4, 5, or 6IDC/NAC 1, 2, 7, or 8
Detector Base
1 4
2 3
INITIATING DEVICE CIRCUIT (IDC)
IDC
/NA
C #
1
IDC
/NA
C #
2
IDC
#3
IDC
#4
NA
C IN
1/2
To TB1 on Module
1 2 43 5 6 7 8 9 10
TXJP1
JP3
11
11
22
22
33
33
JP2
JP4
RX
TB1
TB2
IDC
/NA
C #
8
IDC
/NA
C #
7
IDC
#6
IDC
#5
NA
C IN 7/
8
124 35678910
Initiating Device Circuit (Hardwired) Module
The 3-IDC8/4 is ideal for retrofit projects where existing wiring, smoke detectors and signals may not need replacing.
Flexibility built right into the IDC module allows connec-tion of normally open contact devices, and traditional 2-wire smoke detectors.
The 3-IDC8/4 also configures for use with N.O. contacts and supports supervised supervisory and monitor cir-cuits with latching or non-latching operations. When the monitor operation is used with the non-latching function, the circuit serves as a supervised event follower. This efficiently covers critical fan and damper operations. Circuits can annunciate on the 3-LCD, control display modules, or at any other display device on the network.
All circuits may be programmed for non-verified or verified smoke operation. Ranges include open circuit, shorted condition, and high and low impedance (rela-tive to the main impedance setting). This allows the use of various detectors of similar impedance, as well as 4-state European alarm circuit operation.
Four of the eight 3-IDC8/4 circuits are convertible to Class B notification appliance circuits. The circuits em-ploy traditional reversing polarity operation for polarized bells, horns, and strobes.
Notification appliance circuits are arranged in pairs. Each pair distributes 3.5 Amps at 24 Vdc from the local rail or a single riser. Riser sources sup-ported include 24 V @ 3.5 A, which can be pulsed (temporal pattern) for audible signals, or up to 70 Vrms @ 100W audio source for speakers. For Regulated signals, the IDC supports one NAC pair to distribute up to 1 Amp from the 3-PPS primary power supply through the local rail.
3-IDC8/4 Initiating Device Circuit Module Data Sheet E85010-0061
Addressable Analog Device Controller
The 3-AADC1 Addressable Analog Circuit Module is a local rail module used on the EST3 system. The module requires one connection on the rail chassis. The module can support 99 addressable analog sensors and 99 addressable modules. The controller also features a hinged front panel for a Control Display Module, available in a variety of LED and/or switch configurations.
3-AADC1 Addressable Analog Module Data Sheet E85010-0128
1 2 43 5 6 7 8 9 10
LOOP
CLASS A WIRING
To TB1 on 3-AADC1 Module
+ - + -
Circuit #1
MonitorModule
IonizationSmoke
Detector
IsolatorModule
Photo-electric
Smoke Detector
HeatDetector
MonitorModule
ControlModule
Class AReturn Wiring
MonitorModule
IsolatorModule
Photo-electric
Smoke Detector
MonitorModule
Now supports FAST UIO6 and RZB modules
ES
T3
N
etw
ork
6
EST3 N e t w o r k
SUBMIT
Off Premise Signaling Module
The 3-OPS supports three separate off premises signaling modes of operation:
‘Old’ style reverse polarity operation has only a single reversed polarity output. In the normal state the output is 24 Vdc current limited to 6 mA. In the alarm state the polarity reverses. Should the EST3 panel go into trouble from the normal state, the voltage is removed from the output terminals of the 3-OPS. This change will be detected by the central station as a trouble. Alarm always has priority over trouble. Trouble relay contacts must be configured for normally-closed operation.
‘New’ style reverse polarity operation allows the 3-OPS to output three independent reversing polarity signals. These are alarm, supervisory, and trouble. In each case an active condition causes the terminal output voltage to reverse. Should the central station detect a loss of voltage, the condition is due to line failure. When configured for “new” style operation, a set of trouble contacts is available.
City Tie connection. In this configuration the 3-OPS has terminals for a local energy master fire alarm box. The module operates into a 14 ohm coil and supervises the city tie connection for open conditions. Trouble relay contacts are configurable for normally-open or normally-closed.
3-OPS Off Premise Signaling Module Data Sheet E85010-0075
TROUBLE RELAYTERMINALS 1 & 2
124 35678910
MUNICIPALCIRCUIT
(+)
MASTER BOX
Note: Trouble relay contacts areconfigurable for N.O or N.C
124 35678910
(+)
(+)
(+)
ALARM
TROUBLE RELAYTERMINALS 1 & 2
TROUBLE
SUPERVISORY
124 35678910
(+) ALARM Polarity ReversesTROUBLE Power offALARM has priority
Fiber Optics Communications Interface
Fiber optic communications provide a high level of immunity from electrical noise. Circuits are power limited and suitable for use through hazardous atmospheres. Fiber optic circuits also provide a high level of security and are resistant to the effects of moisture.
EST3 networks easily configure to single or multi mode fiber optic or combination fiber optic/copper networks using the 3-FIBMB2 Fiber Optic Communications Interface and the appropriate fiber optic transceivers.
The 3-FIBMB2 electronics card plugs right into the CPU. A rib-
bon cable connects the 3-CPU directly to the 3-FIBMB2 fiber interface card. The interface card mounts in the ½ footprint space in a 3-CHAS7 chassis or 3-CAB5 enclosure.
The 3-FIBMB2 supports from one to four single or multi mode transceivers. The SMXLO2 standard output single mode transceiver is suitable for distances up to approximately 8.7 miles (14km). The SMXHI2 high output single mode transceiver is available to span distances up to approximately 24 miles (40km). For multi mode applications, the MMXVR transceiver is suitable for distances up to approximately 8,000ft (2,400m).
3-FIBMB2 Fiber Optic Communications Interface c/w 3-CHAS7/3-CAB5 mounting brackets Data Sheet E85010-0131
SMXLO2 Plug-In standard output single mode transceiver for 3-FIBMB2 Data Sheet E85010-0131
SMXHI2 Plug-In high output single mode transceiver for 3-FIBMB2 Data Sheet E85010-0131
MMXVR Plug-In standard output multi mode transceiver for 3-FIBMB2 Data Sheet E85010-0131
Fiber-optic networkdata riser
Maintain physical separationor two-hour fire rating
From 3-ASU primary audio data
CPU with 3-FIBMB2
AA
UD
IOB
AUD
IO
AD
ATA
BD
ATA
RX
TXRX
T XR
XTX
RX
TX
AAU
DIO
BA
UD
IO
AD
ATA
BD
ATA
RX
TXRX
T XR
XTX
RX
TX
AA
UD
IOB
AUD
IO
AD
ATA
BD
ATA
RX
TXRX
TXR
XTX
RX
TX
AA
UD
IOB
AU
DIO
AD
ATA
BD
ATA
RX
TXRX
TXR
XT X
RX
TX
CPU with 3-FIBMB2
CPU with 3-FIBMB2
CPU with 3-FIBMB2
Fiber-optic audiodata riser
AdataRX
TX
RXTX
Bdata
RXTX
RXTX
Aau
dio
Bau
dio
AdataRX
TX
RXTX
Bdata
RXTX
RXTX
Aau
dio
Bau
dio
AdataRX
TX
RXTX
Bdata
RXTX
RXTX
Aau
dio
Bau
dio
AdataRX
TX
RXTX
Bdata
RXTX
RXTX
Aau
dio
Bau
dio
NetworkOUT INA
+A-
B+
B-
AUDIOA IN
+ -
AUDIOA OUT+ -
AUDIOB IN
+ -
AUDIOB OUT+ -
NetworkOUT INA
+A-
B+
B-
AUDIOA IN
+ -
AUDIOA OUT+ -
AUDIOB IN
+ -
AUDIOB OUT+ -
NetworkOUT INA
+A-
B+
B-
AUDIOA IN
+ -
AUDIOA OUT+ -
AUDIOB IN
+ -
AUDIOB OUT+ -
NetworkOUT INA
+A-
B+
B-
AUDIOA IN
+ -
AUDIOA OUT+ -
AUDIOB IN
+ -
AUDIOB OUT+ -
3-CPU Class A network and audio fiber-optic connections
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
7
EST3 N e t w o r k
SUBMIT
Modem Communicator
The Modem Communicator is a two-way local rail module that performs a variety of off-premise communications functions for the EST3 system unavailable on any other system. The module has provisions for supervising two loop-start telephone lines. It features a modular jack for telephone line connections, as well as database download from a PC. The Modcom’s configuration and firmware can also be updated from any network node.
Modcom series modules occupy a single local rail space and can be mounted in any node on the network. Any EST3 Control/Display module can be mounted on the face of a Modcom series module. Power for the Modcom is supplied by the EST3 system supply.
The Modcom provides an enhanced level of survivability in the event of a network CPU failure by notifying the Central Monitoring Station of the failure and entering a degraded mode of operation. In degraded mode, the Modcom can transmit a default fire alarm message during a fire alarm condition.
Two versions of the Modcom are available:
3-MODCOM - This internal modem is a V.32bis 14.4K baud full duplex modem. The modem permits the remote upload and download of system data via a telephone line.
3-MODCOMP – In addition to all modem and dialer (DACT) functions of the 3-MODCOM, the 3-MODCOMP can dial directly into paging systems using Telelocator Alphanumeric Protocol (TAP). Alphanumeric system data can be sent to a single pager or groups of pagers. Some pager services can forward messages via e-mail and Fax.
Each Modcom can buffer up to 500 events in its event queue. It reviews all active events in the queue and identifies the highest priority event and dials the associated receiver. The Modcom then identifies all other events in the queue that are destined to the same receiver as the highest priority event. All event information for that receiver is then trans-mitted. The next high priority event is identified and the process repeated.
The Modcom series has been designed for installation on the same phone lines with other devices such as faxes and answering machines. The module makes its first dial out attempt on either of the two phone lines that is not in use. This prevents unnecessary interruption of calls in progress by the line seizure relays. In the event that both lines are busy, the module seizes one of the busy lines. A fixed DACT testing time can be set at an off-hour, e.g. 2:00am, again minimizing inter-ruptions.
The answering machine override feature permits Modcom modules to be installed on a standard telephone line. The Modcom series also has the ability to detect Type 2 and Type 3 distinctive ringing patterns, permitting it to share its phone lines with other devices and still have a unique phone number for incoming calls.
3-MODCOM Modem/Dialer (DACT) version Data Sheet E85010-0107
3-MODCOMP Modem/Dialer (DACT) w/TAP Protocol Data Sheet E85010-0107
RJ31X
8 PIN MODULAR
CONNECTOR FOR
PHONE LINE #2
TO PHONE LINE #2
(WIRED SAME AS
PHONE LINE #1)
1 8
7
6
54
3
2
RING
(RED)
TIP
(GREEN)
RJ31X
8 PIN MODULAR
CONNECTOR FOR
PHONE LINE #1PREMISES
PHONES
7 Ft.
(2.13 M)
BLACK
YELLOW
SURGE
PROTECTOR
1 8
7
6
54
3
2
LINE 1 LINE 2
MODCOM(front view)
3-Modcom Typical Wiring
ES
T3
N
etw
ork
8
EST3 N e t w o r k
SUBMIT
Power
Supply
Power
Supply
J8
J9
J10
J11
J8
J9
J10
J11
Central
Processor
Unit
3-CPU1
L
R
MAlarm
Silence
Panel
SilenceDrillReset
Alarm Sup'y Trouble Monitor
1
4
7
2
5
8
0
3
6
9
Power TestCPU
Fail
GND
FaultDisable
Previous
Message
Next
Expanded
Message
Command
Menu
Date and Time
EST3 system
Liquid Crystal Display Modules
LCD display modules provide system control and annunciation from any network node location at which they are installed. Modules feature backlit high-contrast supertwist graphical displays and mount to
the local rail over the node’s central processing unit (3-CPU3). Simple-to-understand LEDs and switches help the emergency user display information and execute system commands with confidence.
3-LCDXL1 modules feature large screens that support 24 lines of text 40 characters in length – enough space to display eight events simulaneously. It occupies four local rail module spaces.
3-LCD modules support eight lines of text 21 characters in length. They occupy two local rail module spaces.
EST3 networks can support any combination of 3-LCDXL and 3-LCD display modules.
3-LCDXL1 21 Line Liquid Crystal Display Module Data Sheet E85010-0135
3-LCD 8 Line Liquid Crystal Display Module Data Sheet E85010-0071
Control Display Modules
EST3 Control Display modules provide the emergency user with the simplest of interfaces: lights and switch controls. Control Display Modules install over local rail modules. There are five types of modules available.
The first module supports simple zone annunciation; the second, zone annunciation with zone dis-able; the third, alarm and trouble zone annunciation; the fourth, alarm and trouble zone annuncia-tion with zone disable. Typically, alarm zone annunciation appears on any of these module types.
The fifth module is very adaptable to system requirements for audio or remote equipment control. Each contains 18 LEDs and 18 switches. And each group of three switches has a latching-interlock to support operations that must be kept separated. The interlock is under software control so only one switch is active at a given time.
3-LDSM LED Display Support Module Data Sheet E85010-0055
3-24R Display Module: 24 red LED Data Sheet E85010-0055
3-24Y Display Module: 24 yellow LED Data Sheet E85010-0055
3-24G Display Module: 24 green LED Data Sheet E85010-0055
3-12SR Display/Control Module: 12 switches with 12 red LEDs Data Sheet E85010-0055
3-12SY Display/Control Module: 12 switches with 12 yellow LEDs Data Sheet E85010-0055
3-12SG Display/Control Module: 12 switches with 12 green LEDs Data Sheet E85010-0055
3-12RY Display Module: 12 red LEDs and 12 yellow LEDs Data Sheet E85010-0055
3-12/2Y Display Module: 12 groups of 2 yellow LEDs Data Sheet E85010-0055
3-12/RY Display Module: 12 groups of 1 red and 1 yellow LED Data Sheet E85010-0055
3-12/S1GY Display/Control Module: 12 switches with 1 green and 1 yellow LED per switch Data Sheet E85010-0055
3-12/S1RY Display/Control Module: 12 switches with 1 red and 1 yellow LED per switch Data Sheet E85010-0055
3-12/S2Y Display/Control Module: 12 switches with 2 yellow LEDs per switch Data Sheet E85010-0055
3-6/3S1G2Y Display/Control Module: 6 groups of 3 switches, 1 LED each: green, yellow, yellow Data Sheet E85010-0055
3-6/3S1GYR Display/Control Module: 6 groups of 3 switches, one LED each: green, yellow, red Data Sheet E85010-0055
3-4/3SGYWR Display/Control Module: 6 groups of 3 switches, one LED each: green, yellow, white/red Data Sheet E85010-0055
Control, Display & Annunciation
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
9
EST3 N e t w o r k
SUBMIT
FireWorks
FireWorks is an incident management command and control platform that comprises hardware, software, and networking components that together provide a powerful and cohesive Mass Notification and Life Safety solution. Sophisticated networking technology allows it to integrate seamlessly with EDWARDS life safety solutions, yet FireWorks remains fully interoperable with third-party equipment, making it ideal for system upgrades or new installations alike.
FireWorks can automatically trigger programmed responses to facility events, or it can act as an operator interface for manual control. The FireWorks user interface provides a clear, concise, and coordinated view of any situation by presenting information strategically.
Five configurable graphical viewports offer simultaneous insight into different aspects of an incident, while the underlying software dynamically manages content in each viewport based on real-time events and user interaction. Facility maps, live video feeds, audio channels, protocol information, and fingertip control over vital equip-ment all come together instantly within view of an operator facing events that require solid information and split second timing.
Supporting every FireWorks workstation is a sophisticated network backbone – strong enough to handle coordinated critical control functions from as many as fifty client worksta-tions and many other devices, yet flexible enough to manage integration with third-party mass notification systems.
Redundant server options eliminate risk of communications breakdowns by providing alternate data paths that regenerate communications in the event of signal loss. FireWorks can operate on an existing local area network, or provide facility access from anywhere in the world via secured Virtual Private Network (VPN) connections.
For more information please refer to Data Sheet E85006-0068.
Servers and Workstations FW-UL6S Server/Workstation. Xeon processor, 128 GB RAM, RAID1 500GB array, dual power supplies.
FW-UL6W Workstation. i7 Intel processor, 32 GB RAM, RAID1 500GB SSDs. Single power supply.
Sofware FW-CGS Standalone package. Allows full 5 viewport display. Includes FW-FIREKEYUSB. No common control.
FW-CGSUL Standalone package. Allows full 5 viewport display. Includes FW-FIREKEYUSB. With common control.
Non-Redundant Servers: FW-NSZ5FP, 5 seat. FW-NS15FP, 15 seat.
Redundant Servers: FW-RSZ5FP, 5 seat. FW-RS15FP, 15 seat. FW-RS25FP, 25 seat. FW-RS50FP, 50 seat.
FW-NCZZFP Non-Redundant Server Client license.
FW-RCZZFP Redundant Server Client license.
Software options 85012-0019 FireWorks Software DVD only.
WebClients: FW-1S, One seat. FW-4S, Four seats (Requires FW-1S). FW-10S, (Requires FW-1S & FW-4S).
FW-DARCOM Sofware for Communication to DACRs and/or IPMON1000.
FW-FAST FAST AutoCAD® reader and panel building sofware for FireWorks Server or Standalone system.
FW-HSSD5 VESDA HLI Interface for up to 5 nodes. Each server must have its own FW-HSSX1.
FW-HSSD20 VESDA HLI Interface for up to 20 nodes. Each server must have its own FW-HSSX1.
FW-IPMON1000 Interface for up to 1,000 connections to iO Series panels. Requires FW-DARCOM software option.
Monitors FW-22LCDWTS 22-inch 16:9 LCD 115 Vac 1680x1050 resolution capacitive touch screen with integral speakers.
FW-42LCDWTS 42-inch 16:9 LCD 115 Vac 1920x1080 resolution surface acoustic wave touch screen.
See Data Sheet E85006-0068 for complete FireWorks ordering information.
ES
T3
N
etw
ork
10
EST3 N e t w o r k
SUBMIT
Graphic Annunciation
Graphic annunciators and smoke control panels are custom designed to present complex status and control information in an easy to understand pack-age. The design of the annunciator permits users to rapidly determine system status and easily operate associated system controls.
3-EVDVRA driver module assemblies connect the EST3 control panel to the display panel of an LED based graphic annunciator. Each driver card supports up to 24 LEDs and 12 switches on the graphic panel display. Attached to a plastic mounting rail, the driver boards fit easily into custom Graphic annunciators. The annunciator driver communicates with the EST3 control panel on the RS 485 network. This can be configured for Class A or Class B communication.
National and local installation and approvals should always be adhered to when selecting a graphic panel supplier.
3-EVDVRA LED/SWITCH Driver Module Assembly.
3-EVDVRX Plastic mounting extrusion. Mounts up to three 3-EVDVRA modules.
3-EVPWRA Power Supply Assembly. Assembled version of 3-EVPWR. Used for third party graphics.
3-ANNCPU3 Annunciator CPU. One Required per graphic annunciator.
24VDC FROM 3-PPS/MOR 3-BPS/M POWER RISER
FROM PREVIOUS PANELRS-485 NETWORK DATA
POWER MODULE
RS-485 NETWORK DATATO NEXT PANEL
24VDC TO NEXT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
11
EST3 N e t w o r k
SUBMIT
Local Operations Consoles
EST3 remote annunciation and control equipment is ideally suited for mass notification purposes. LCD display modules, remote micro-phones, and control and display modules configured for mass noti-fication operation provide everything that’s needed for annunciation, control, and paging operations. In these applications, annunciators are configured to operate as Local Operation Consoles (LOCs), from which mass notification is initiated and controlled.
See Data Sheet E85010-0148 for more information.
Remote Annunciators
Use EST3 remote annunciators wherever a com-pact system status display is needed. Annunciator configurations include: LCD only display, LED only display, or combination LED and LCD display in a single enclosure. Display and control is provided by the 3-LCD and Control Display Modules. Control/Display modules install over any annunciator sup-port module, maximizing annunciator design flex-ibility. A lamp test feature can program to any spare control switch. If a 3-LCD display is installed in the annunciator, simply operate the Alarm Silence and Trouble Silence switches simultaneously to lamp test all LEDs. 3-REMICA remote microphones can also be installed in annunciator cabinets.
3-LCDANN Remote LCD Command Module Annunciator Data Sheet E85010-0069
3-4ANN Four Position Base Annunciator Data Sheet E85010-0069
3-6ANN Six-position Base Annunciator Data Sheet E85010-0069
3-10ANN Ten-position Base Annunciator Data Sheet E85010-0069
3-ANNCPU3 Annunciator CPU Data Sheet E85010-0069
3-ANNSM Annunciator Support Module Data Sheet E85010-0069
3-LCD Liquid Crystal Display Module Data Sheet E85010-0069
3-LCDXL1 Liquid Crystal Display Module, 40 lines Data Sheet E85010-0069
3-REMICA Remote microphone for use in 3-ANN series annunciator cabinets Data Sheet E85010-0069
3-ANNBF Blank Filler Plate Data Sheet E85010-0069
3-EVDVRA LED/Switch Driver Module Assembly for Third-party Graphics Data Sheet E85010-0069
3-EVPWRA Power Supply Assembly with 19” rail mounting chassis assembly Data Sheet E85010-0069
3-EVDVRX Plastic mounting extrusion 19-inch mounting Data Sheet E85010-0069
Remote Annunciator CabinetsRemote LCD Command module Wallbox RLCM/B (flush) RLCM/B-S (Surface) Data Sheet E85010-0069 6-position LED/LCD Wallbox 6ANN/B (flush) 6ANN/B-S (Surface) Data Sheet E85010-0069 10-position LED/LCD Wallbox 10ANN/B (flush) 10ANN/B-S (Surface) Data Sheet E85010-0069 4-position LED/LCD Wallbox 4ANN/B (flush) 4ANN/B-S (Surface) Data Sheet E85010-0069
TX RX
TXRX
TX RX
TXRX
TX RX
TXRX
TX RX
TXRX
EA
RT
H G
RO
UN
DTo BackboxGround Lead
Rear View
24V
DC
24V
DC
NE
TW
OR
K A
NE
TW
OR
K B
SPA
RE
To TB1 on 3-ANNCPU1
1 2 43 5 6 7 8 9 10
See Page 8 for Control Display modules. See Page 14 for Remote Microphones.
ES
T3
N
etw
ork
12
EST3 N e t w o r k
SUBMIT
Mass Notification
VoIP Encoder/Decoder
Edwards Voice over Internet Protocol (VoIP) encoder/decoder units allow for the use of Transmission Control Protocol/Internet Protocol (TCP/IP) to transmit supervised digital audio for mass notification and life safety applications.
MN-FVPN MN-FVPN VoIP Encoder/Decoder. Data Sheet E85010-0143
Mass Notification Serial Communications/LAN interface
The MN-COM1S is a TCP/IP to RS-232 interface with one RJ-45 port and one RS-232 port. It is used in mass notification settings to connect a FireWorks workstation to an EST3 control panel.
MN-COM1S FireWorks Communications Ethernet Port, Command & Control. Data Sheet E85010-0144
Ethernet Network I/O Module
The Edwards MN-NETLRY4 Network Relay provides four unsupervised input zones and four normally-open relays to and from FireWorks V1.6 or greater over an Ethernet (TCP/IP) net-work. This module is particularly well-suited for mass notification, life safety applications, and other monitoring or output applications. It is also ideal for interfacing to third-party systems.
MN-NETRLY4 Ethernet controllable multi I/O unit, 4 input 4 relay outputs Data Sheet E85010-0149
Related Equipment (Data Sheet E85010-0144) MN-BRKT1 MN-FVP mounting bracket for EST3 enclosures
MN-BRKT3 MN-FVP mounting bracket for APS-(6)(10)A power supplies
MN-FVPB1 Polymer mounting bracket for MN-FVPN
MN-FVPN Fire VoIP encoder/decoder, includes power and audio cables
MN-PASM2 MN-FVPN preamp signal supervisory booster module
SIGA -RM1/MRM1 Riser Supervision Module
MN-ABPM Audio Bridge (Panel mount 3-ATPINT)
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
13
EST3 N e t w o r k
SUBMIT
Managed Ethernet Switches
The MN-FNS Series managed Ethernet switches are advanced managed switch solutions that provide for a fully scalable Ethernet network to sup-port virtually any life safety application. These networks may be dedicated for use by mass notification systems or where permitted, may be part of a non-dedicated facility network.
MN-FNS switches are field-tested and designed for use with EST FireWorks® Computer Platforms, EST3, EST3X and other EDWARDS panels and panel networks. They may also interface to non-dedicated facility networks, and even to competing control panels through existing network infrastructure. This makes them ideal for many retrofit applica-tions. MN-FNS Ethernet switches may be interconnected to build spoke format networks, as well as Class B, Class X, Mesh, and Hybrid systems. MN-FNS Series Ethernet switches are powered by Cisco® Technologies and are listed to UL 864 and ULC S527.
Dedicated Class X
21
EXPRESSSETUP
IE 2000
DC-A+
–
DC-B+
–
±12/24/480.5-2.0A
USB EXP SYS
CO
NSO
LE
LARMIN1 IN2 OUT
IN1
REF
IN2
COM
5X 8X
1X 4X
1X
7X
2X
8X
2
1
2
1
21
EXPRESSSETUP
IE 2000
DC-A+
–
DC-B+
–
±12/24/480.5-2.0A
USB EXP SYS
CO
NSO
LE
LARMIN1 IN2 OUT
IN1
REF
IN2
COM
5X 8X
1X 4X
1X
7X
2X
8X
2
1
2
1
21
EXPRESSSETUP
IE 2000
DC-A+
–
DC-B+
–
±12/24/480.5-2.0A
USB EXP SYS
CO
NSO
LE
LARMIN1 IN2 OUT
IN1
REF
IN2
COM
5X 8X
1X 4X
1X
7X
2X
8X
2
1
2
1
21
EXPRESSSETUP
IE 2000
DC-A+
–
DC-B+
–
±12/24/480.5-2.0A
USB EXP SYS
CO
NSO
LE
LARMIN1 IN2 OUT
IN1
REF
IN2
COM
5X 8X
1X 4X
1X
7X
2X
8X
2
1
2
1
Cat 5
Fiber
Cat 5
Fiber
Cat 5
Fiber
Cat 5
Fiber21
EXPRESSSETUP
IE 2000
DC-A+
–
DC-B+
–
±12/24/480.5-2.0A
USB EXP SYS
CO
NSO
LELARM
IN1 IN2 OUT
IN1
REF
IN2
COM
5X 8X
1X 4X
1X
7X
2X
8X
2
1
2
1
Cat 5
R e s i l i e n t E t h e r n e t P r o t o c o l
Ethernet Switches & Power Supplies MN-FNS4C2F3 4 Fast Ethernet (RJ45), 2 GB SFP, Layer 3 Lite. 24 VDC. Data Sheet E85010-0153
MN-FNS8C18F2 Rack-mount, 8 Fast Ethernet (RJ45), 16 FE SFP, 2 GB, Layer 2. Data Sheet E85010-0153
MN-FNS8C18FAC 100-250 VAC/VDC power supply module, primary or backup. Data Sheet E85010-0153
MN-FNS8C18FDC 24 VDC power supply module, primary or backup. Data Sheet E85010-0153
MN-FNS8C2F3 8 Fast Ethernet (RJ45), 2 GB, SFP/RJ45, Layer 3 Lite, 24 VDC. Data Sheet E85010-0153
Ethernet Switch Mounting Hardware MN-BRKT1F Switch mounting bracket for EST3 enclosures Data Sheet E85010-0153
MN-BRKT3F Switch mounting bracket for APS6A/10A Series power supplies. Data Sheet E85010-0153
MN-BRKT8C18F EST3 cabinet mounting bracket . Data Sheet E85010-0153
MN-FNSRMK1 MN-FNS8C18F Series switch installation kit. Data Sheet E85010-0153
MN-FNS4HDK1 MN-FNS4 Series switch holder bracket. Data Sheet E85010-0153
MN-FNS8HDK1 MN-FNS8 Series switch holder bracket. Data Sheet E85010-0153
Tranceiver Modules (Dual filament, LC Connectors) MN-FNSFEDSM10K Single mode fiber, , FE, 0m to 10km, 9.5 dB fiber budget, 1310nm. Data Sheet E85010-0153
MN-FNSFEMM2K Multimode fiber, FE, 0m to 2km, 9 dB fiber budget, 1310nm. Data Sheet E85010-0153
MN-FNSGBDSM70K Single mode fiber, GB, 10m to 70km, 17.2 dB fiber budget, 1550nm. Data Sheet E85010-0153
ES
T3
N
etw
ork
14
EST3 N e t w o r k
SUBMIT
J7BOUT
J6DIN
J3 J4
BIN
J2
J5
J1
J8 J9
COUT DOUT
AOUTAIN CIN
RAILEXPCARD
J4
J2
J1
TR RX RXTX PRIMARY
AUDIO DATA REMOTE MIC
SECONDARY TELEPHONEPAGEOUT KEY AUDIO AUX
TX
1 2 3 4
TB11 14
AudioSource
Card
J1
TB1TX RX
J3
J2FirePhoneCard
ALL CALL
READY TOPAGE
Page toEvac
Page toAlert
All CallMinus
Page byPhone
0 call(s) pending
DISCONNECT REVIEW CONNECTED
CONNECT REVIEW PENDING ACK
EMERGENCY TELEPHONE
Network AudioConfiguring EST3 audio is a matter of selecting components for installation in standard fire alarm cabinet assemblies. EST3 uses zoned amplifiers. This reduc-es wire runs and space needs at a central location. Audio control equipment and zoned amplifiers use the same system power supplies as fire alarm components. All these components are supported by a common standby battery. Where multiple nodes make up the system, a single pair of wires carries eight channels of digital audio between nodes.
Audio and Telephone MastersThe Audio Source Unit converts analog signals to digital signals. Sampling the analog signal 9600 times per second
provides high quality reproduction of audio sources. On-board audio memory stores signal tones and/or alarm-alert verbal messages. The ASU comes standard with two minutes of memory for tone and message storage. The ASU comes standard with two minutes of mem ory for tone and message storage. Available message memory expands easily to 100 minutes with the optional 3-ASUMX/100 memory expansion card. The ASU supports 3 and 4 state operation per UL864 10th edition.
Audio Source Units support connection of a local microphone, remote microphone, telephone voice line, and auxiliary audio input. With eight audio channels, combinations of paging, alert, evacuation signaling and automatic messages are available for simultaneous delivery to different parts of a building.
When the system requires paging, only the 3-ASU or 3-ASU/4 Audio Source Units provide a master paging microphone with common controls. Switch labeling makes the operation intuitive. Six LEDs and five switches cover paging operations.
Audio Source Units mount in one chassis space of a EST3 Lobby Enclosure. In addition to the paging microphone, the 3-ASU/4 has mounting space for up to four local rail modules, including 20, 40, and 95 watt zone amplifiers, and up to four Control Display modules. This increases layout flexibility. The 3-ASU provides the same functionality as the 3-ASU/4 but is supplied with an inner door filler plate and no local rail module spaces.
The 3-FTCU contains the master telephone handset that pro-vides an analog telephone riser for two-way communications between the fire command station and firefighter’s telephone stations installed in the facility. The 3-FTCU features an alpha-numeric display that indicates both incoming and connected calls. Up to five remote telephones may be connected to the riser simultaneously. The fire command center operator can also use the telephone circuit as a page source, permitting paging via the telephone system.
3-ASU/FT* Audio Source Unit with local microphone and firefighters’ telephone Data Sheet E85010-0063
3-ASU/4* Audio Source Unit with local microphone (provides four local rail spaces) Data Sheet E85010-0063
3-ASU* Audio Source Unit with local microphone and inner door filler plate Data Sheet E85010-0063
3-FTCU* Firefighters’ Telephone Control Unit with inner door filler plate Data Sheet E85010-0063
3-ASUMX/100* Audio Source Unit Memory Expansion (100 minutes of message time) Data Sheet E85010-0063
3-CCI City of Chicago Interface
* Add “-CC” for City of Chicago approved equipment
Dashed Wires Requiredfor Class 'A' Wiring Only
Typical Fire Fighter's Telephone Circuit
Telephone RiserTwisted Shielded Pair
Twisted Shielded Pairif run with other wiring
Connect Shield toEarth Ground onlyat the panel. Maintainshield continuity.
To SignatureData Circuit
To SignatureData Circuit
To Phones
ULI/ULC Listed47K ohm EOL Resistor
48 37 26
10
15
9
CC1
48 37 26
10
15
9
CC1
MAIN PROCESSOR MODULE
11 112 214 413 315 516 617 718 819 920 10
Net
wor
k D
ata
Rise
r
From previous panel3-CPU Module
To next panel3-CPU Module
Net
wor
k A
udio
Ris
er
Connect to TB2 on 3-CPU Module
3-CPU
Connect to TB1 on 3-CPU3 Module
NC C NO NO C NC NO C NCTROUBLE ALARM SUP
N/A
To external troubleinput circuit
To external alarminput circuit
To external supervisoryinput circuit
Control Panel
Audio Source Unit
3-ASUor
3-ASUFT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
15
EST3 N e t w o r k
SUBMIT
Audio Amplifiers (Zoned)EST3 audio amplifiers decode and re-expand the eight multiplexed audio signals on the network audio riser. Under command of the network, one of the available eight signals is selected to be dis-tributed over the speaker circuit. Command and control signals for the amplifier are sent and received via the network data riser in response to programming.
Amplifiers are available in 20, 40 or 95 watt versions, with su-pervised, power limited 25 Vrms or 70Vrms outputs. The amplifier output is wired to a single speaker zone. Each amplifier has a 1 KHz temporal tone generator used as evacuation signal in the event of a fault with the network audio circuit.
3-ZA20A 20 Watt Zoned Amplifier w/Class A/B Audio & Class A/B 24 VDC outputs Data Sheet E85010-0057
3-ZA20B 20 Watt Zoned Amplifier w/Class B Audio & Class B 24 VDC outputs Data Sheet E85010-0057
3-ZA40A 40 Watt Zoned Amplifier w/Class A/B Audio & Class A/B 24 VDC outputs Data Sheet E85010-0057
3-ZA40B 40 Watt Zoned Amplifier w/Class B Audio & Class B 24 VDC outputs Data Sheet E85010-0057
3-ZA95 95 Watt Zoned Amplifier w/Class A/B Audio output Data Sheet E85010-0057
COMMON ENCLOSURE
AUDIOAMPLIFIERMODULE
(ZONE #1)
AUDIOAMPLIFIERMODULE
(ZONE #2)
AUDIOAMPLIFIERMODULE
(ZONE #3)
AUDIOAMPLIFIERMODULE
(BACKUP)
1 2 43 5 6 7 8 9 101 2 43 5 6 7 8 9 10 1 2 43 5 6 7 8 9 10 1 2 43 5 6 7 8 9 10
124 35678910 124 35678910 124 35678910124 35678910
VISUAL NOTIFICATIONAPPLIANCE CIRCUIT + +
- -+ +- -
+ +- -
AUDIO NOTIFICATIONAPPLIANCE CIRCUIT
Audio Amplifiers (Banked)Banked Amplifiers provide EST3 with econo-my audio configurations for single and some dual channel applications. Model 3-ZA20A/B Zoned Amplifiers at the EST3 control panel provide channel sources for banked ampli-fiers. 3-ZA20A/B amplifiers can select any of
EST3’s eight audio channels as a signal source. A special interface module, the 3-ATPINT, accepts analog audio signals at 25 or 70Vrms from EST3’s Zoned Amplifiers and passes these signals to the 1B3125 and 1B3250 Audio Power Amplifiers. The 3-ATPINT mounts in the ATP. The ATP Audio Terminal Panel interfaces one or two audio power amplifiers and monitors utility power, charges and supervises standby batteries, and provides switch-over to standby. The amplifier bank is monitored and controlled through Signature Series modules.
EST3 Central Banked Amplifiers Data Sheet E85010-0085
1B3125 Audio Power Amplifier — 125 Watts Data Sheet E85010-0011
1B3250 Audio Power Amplifier — 250 Watts Data Sheet E85010-0013
ATP Amplifier Terminal Panel Data Sheet E85300-02741
3-ATPINT ATP Interface Module Data Sheet E85010-0085
SIGA-RM1/MRM1 Riser Monitor Module Data Sheet E85001-0535
RKU 19-inch Equipment Rack Data Sheet E85300-02738
Intelligent Audio Amplifiers
Signature Series amplifiers are high-efficien-cy switch mode audio amplifiers available in 30 and 50 watt sizes. Amplifiers have two input channels supporting dual channel or single channel audio applications. Signature amplifiers are ideally suited for distributed au-dio applications and small centrally banked applications. The audio output is configu-rable as 25Vrms or 70Vrms in Class B or Class A wiring configurations.
SIGA-AA30 30 Watt Intelligent Audio Amplifier Data Sheet E85010-0089
SIGA-AA50 50 Watt Intelligent Audio Amplifier Data Sheet E85010-0089
To 24 VDC
From Output of
Backup Amp
To Backup Input
of Next Amp
Shield Optional
Output Return
Class A Only
Audio Output
to Speakers or
Signature device
Output Voltage
Selection Jumper
To Next
Signature Device
From Previous
Signature Device
From Channel 1
Signal Source
1Vrms or 25Vrms
To Next Amp
Channel 1 Input
To Next Amp
Channel 2 Input
From Channel 2
Signal Source
1Vrms or 25Vrms
Status LEDs
Status LEDs
ATP
Amplifier
Amplifier
RKU Equipment Rack
CC2
CC2
Data
Channel 1
Channel 2
RM1 RM1
ES
T3
N
etw
ork
16
EST3 N e t w o r k
SUBMIT
Main Panel Power Supplies
EST3 Power supplies consist of two assemblies, a high efficiency switch mode power supply card and a power supply monitor module. Up to four power supplies may be combined in a single enclosure to provide up to 28 amps of available current. Battery backup is provided using from one to four sets of batteries, depending on standby power requirements to support up to 260 AH batteries
The power supply comes in two styles: a primary supply and a booster supply. Each power supply produces 7 amps of filtered and regulated 24 VDC. The primary power supply provides the system with battery charging and voltage regulation. The booster supplies work in concert with the primary supply are avail-able with or without battery
charging capability. Software configuration configures the battery changing circuits for either 10-24 AH batteries or 30 – 65 AH batteries and controls the high/low charge rate.
EST3 power supplies individually monitor batteries for load defi-ciencies, short circuits, and insufficient voltage levels and report trouble back to the 3-CPU3. The 3-LCD displays any troubles and the power supply’s address, a specific trouble code, and a text message describing the specific trouble.
3-PPS/M Primary Power Supply w/ local rail module 120V 50/60 Hz Data Sheet E85010-0059
3-BPS/M Booster Power Supply w/ local rail module 120V 50/60 Hz Data Sheet E85010-0059
3-PPS/M-230 Primary Power Supply w/ local rail module 230V 50/60 Hz Data Sheet E85010-0059
3-BPS/M-230 Booster Power Supply w/ local rail module 230V 50/60 Hz Data Sheet E85010-0059
3-PPS/M-230-E Primary Power Supply w/local rail module 230V 50 Hz, EN-54 Cert., CE Data Sheet E85010-0059
3-BPS/M-230-E Booster Power Supply w/local rail module 230V 50 Hz, EN-54 Cert., CE Data Sheet E85010-0059
3-BBC/M Booster/Charger Supply w/local rail module 120V 50/60Hz Data Sheet E85010-0059
3-BBC/M-230 Booster/Charger Supply w/local rail module 230V 50/60Hz Data Sheet E85010-0059
3-BBCMON Booster/Charger Monitor Module with charger capability Data Sheet E85010-0059
Power SuppliesEST3 power supplies use a unique paralleling arrangement that ensures optimization of each supply’s full capacity. Each power supply supports up to a 7 amp load. With four supplies, 28 Amps of current is available per cabinet as is battery charging capacity of up to 260 Amp-Hours.
Monitor Module
Power Supply
MasterPowerSupply
BoosterPowerSupply
24Vdc *2 x 3.5A
24Vdc *2 x 3.5A
124 3
UtilityPower
PowerTo Rail
AuxillaryPowerTakeoff2 x 3.5A
MasterPower SupplyMonitor Module
PowerSupplyMonitoring
Rails
124 3
AuxillaryPowerTakeoff2 x 3.5A
24Vdc *2 x 3.5A
24Vdc *2 x 3.5A
124 3
AuxillaryPowerTakeoff2 x 3.5A
BoosterPower SupplyMonitor Module
Rails
124 3
AuxillaryPowerTakeoff2 x 3.5A
BoosterPowerSupply
BoosterPowerSupply
J8
J9
J10
J11
J8
J9
J10
J11
PowerSupply
LRM
Battery Distribution Unit
The 3-BTSEN consists of a circuit breaker and copper bus bars mounted on a sheet metal bracket. The unit provides a backup battery bus for supplying backup power to multiple power supplies fed by a common battery. The 3-BTSEN features a 50 Amp circuit breaker to protect the backup battery. The 3-BTSEN mounts in the BC-1 Battery cabinet or any EST3 “RCC” series enclosure.
3-BTSEN Battery Distribution Unit Data Sheet E85010-0111
12Volts12Volts
RedBlack
Backup Battery Bus Wiring
To Booster 2
and Booster 3
To Driver
and Booster 1
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
17
EST3 N e t w o r k
SUBMIT
Remote Booster Power Supply
The Remote Booster Power Supply is a self-contained 24 Vdc power supply designed to augment fire alarm audible and visual power requirements as well as provide power for auxiliary and security applications. The booster contains all of the necessary circuits to monitor and charge batteries, control and supervise four Class B or two Class A NAC circuits and monitor two controlling inputs from external sources. It also provides the ability to synchronize Genesis series strobes to UL 1971 requirements, and offers independent horn control over two wires.
For comprehensive configuration and wiring details, refer to the BPS Application Guide, 85001-0582.
BPS6A 6.5 Amp Booster Power Supply Data Sheet E85005-0125
BPS6A/230 6.5 Amp Booster Power Supply (220V) Data Sheet E85005-0125
BPS10A 10 Amp Booster Power Supply Data Sheet E85005-0125
BPS10A/230 10 Amp Booster Power Supply (220V) Data Sheet E85005-0125
3-TAMP Tamper switch Data Sheet E85005-0125
BPSEQ Seismic battery hold-down. Supports up to two 6.5 or 10 Ah batteries. Data Sheet E85005-0125
Auxiliary Power Supplies
The Auxiliary Power Supply offers the same advantages as the BPS above, but is supplied with its own extra large enclosure providing space for up to two 24 Ah batteries and additional option modules in a number of mounting configurations. Option modules can be installed on the mounting brackets inside the enclosure or on an MP2L mounting plate at the top of the enclosure. The SIGA-REL, and SIGA-UIO2/6/6R can also be mounted at the top of the enclosure.
APS6A 6.5 Amp Auxiliary Power Supply Data Sheet E85005-0127
APS6A/230 6.5 Amp Auxiliary Power Supply (220V) Data Sheet E85005-0127
APS10A 10 Amp Auxiliary Power Supply Data Sheet E85005-0127
APS10A/230 10 Amp Auxiliary Power Supply (220V) Data Sheet E85005-0127
APSEQ Seismic battery hold-down. Supports up to two 10 - 24 Ah batteries. Data Sheet E85005-0127
Batteries and Battery CabinetsData Sheet E85010-0127
12 Volt Batteries 12V4A (4.5 Ah) 12V6A5 (7.2 Ah) 12V10A (11 Ah) 12V17A (18 Ah) 12V1A2 (1.2 Ah) 12V24A (26 Ah) 12V40A (40 Ah) 12V50A (50 Ah) 12V65A (65 Ah)
6 Volt Batteries 6V8A (8 Ah) 6V10A (12 Ah) Battery Cabinets BC-1 (holds up to two 40 Ah batteries) BC-2 (holds up to two 17 Ah batteries) 3-RCC used as large battery enclosure.
BC-1EQ Seismic battery hold-down for BC-1. Supports up to two 40 Ah batteries. Data Sheet E85010-0067
ES
T3
N
etw
ork
18
EST3 N e t w o r k
SUBMIT
Security
As a true multiplex life safety system, EST3 supports fire alarm as well as security functions. The capacity for this additional functionality is built right into every EST3 panel. All that’s needed to take advantage of it is a handful of specialized components.
Intelligent PIR Motion Detector
The SIGA-MD is a Passive Infrared (PIR) motion detection module that connects directly to the Signature loop. The module uses adaptive signal processing with gliding focus mirror optics to analyze the size, speed and shape to determine the alarm threshold. A tamper switch notifies the host system when the cover is removed. The unit is designed for wall mounting. Curtains and masks are provided.
SIGA-MD Passive Infrared Motion Detector Data Sheet E85001-0526
SIGA-MDS Passive Infrared Motion Detector, swivel mount for 1-gang boxes Data Sheet E85001-0526
Dual Input Security Module
TB1 TB2
1
2
3
4 8
7
6
5_
+
_
+
From Signature
Loop Controller
or previous device
Data In (+)
Data In (-)
Data Out (-)
Data Out (+)
_
+
_
+
Circuit 1
input
Tamper Security open
with fault
Secuity closed
with fault
Tamper
Alarm
Alarm
Tamper
Circuit 2
inputTo next Signature
device
Signature loop
SIGA-SEC2
Basic Security N/O with tamperN/C with tamper
EOL EOL
EOL
EOL
EOLEOL
The SIGA-SEC2 is an intelligent analog addressable device used to connect one or two normally-open or normally-closed dry contact security circuits. The actual function of this module is determined by the “personality code” selected by the installer. This code is downloaded to the module from the Signature loop controller during system configuration.
SIGA-SEC2 Dual Input Security Module Data Sheet E85001-0527
Security/Annunciator Control Module
Class A wiring
Class B wiring
TB2
110
3-SAC Module
KPDISPKeypad
BRS-485 Not
usedNot
usedA
RS-485 GroundG G+ +
From 24 Vdc circuit orlocal 120 Vac
TB2
110
3-SAC Module
KPDISPKeypad
KPDISPKeypad
BRS-485 Not
usedNot
usedA
RS-485 GroundG G+ +
From 24 Vdc circuit orlocal 120 Vac
From 24 Vdc circuit orlocal 120 Vac
120 OhmTerminatingResistor
120 OhmTerminatingResistor
The 3-SAC Security/Annunciator Control Module is a key component that blends security functions into the EST3 multiplex life safety system. The 3-SAC is the demarca-tion point between fire and security functions. All security devices that connect to a 3-SAC are designed, tested and listed to strict fire alarm standards. The 3-SAC is used in combination with the Modcom Modem Communicator. The Modcom’s dialer (DACT) function transmits alarms to one or more central monitoring stations and/or paging terminals.
3-SAC Security/Annunciator Control Module Data Sheet E85010-0109
Keypad/Display
DATA
POWER
24 Vdc
supply
From last device
RS-485
line
+
–
24 Vdc
supply
To next device
RS-485
line
+
–
+ –
+ –
+
–
+
–
The KPDISP transmits and receives information from/to the 3-SAC Security/Annunciator Control module installed in the EST3 system. Communication between the KPDISP and the 3-SAC is supervised, providing unprecedented reliability. Credential holder information is encrypted to provide an additional level of security. KPDISP data is stored in non-volatile memory. Power to the KPDISP is provided by the EST3, ensuring a reliable, supervised and backed-up power source.
KPDISP Keypad/Display Data Sheet E85006-0046
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initiating D
evicesE
ST
3 N
etwo
rk
19
EST3 N e t w o r k
SUBMIT
Network Accessories
EST3 to BMS Communications Bridges
The EST3 Communication Bridges are ancillary devices that provide protocol translation between EST3 serial data and the se rial or Ethernet input of an external device controller. Signal flow is typically one way — from the EST3 network to the building automation system.
FSB-PC2 EST3 to BMS Communications Bridge. Data Sheet E85010-0150
FSB-PCLW EST3 to BMS Communications Bridge. Data Sheet E85010-0150
FSB-BRKT2 MFC-A or Chass7 mounting bracket for FSB-PC2 or FSB-PCLW. Data Sheet E85010-0150
MFC-A Multifunction Fire Alarm Cabinet, red. Data Sheet E85010-0150
Network Short Haul Modem
EST3 networks easily configure for use over existing copper telephone lines using the 3-NSHM Short Haul Modem Communications Interface. The 3-NSHM electronics card, plugs right into the 3-CPU3. A ribbon cable connects the 3-CPU3 directly to the modem interface card. The interface card mounts on the right rear of a 3-CHAS7 chassis. No local rail space is used. The 3-NSHMs the 3-MPFIB mounting bracket for 3-CAB5 enclosure mounting.
3-NSHM1 Network Short Haul Modem, single modem connection Data Sheet E85010-0113
3-NSHM2 Network Short Haul Modem, two modem connections Data Sheet E85010-0113
Ground Fault Detection Module
12345678
111216 15 14 13
To earth ground
24 VDC+
24 VDC-From UL/ULC listedfire alarm panel [4]
9103-2-1
LED 1
JP1
LED 2
+
+
-
-Circuit Pair 1 IN
Circuit Pair 2 IN+
+
-
-Circuit Pair 1 OUT
Circuit Pair 2 OUT
+
-
+
-
From IDC orprevious GFD
To next GFDor EOLR [3] [4]
The GFD module is designed to detect ground fault conditions on either of two independent power or data circuits. Each circuit must be balanced with respect to ground. The module will detect when the resistance between any of the monitored conductors and earth ground drops below 10 K Ohms. Two LEDs are provided to indicate the conductor with the ground condition. A normally energized Trouble/Ground Fault relay is provided with NO/NC relay contacts for interfacing with monitoring systems.
GFD Ground Fault Detection Module Data Sheet E85010-0115
ES
T3
N
etw
ork
20
EST3 N e t w o r k
SUBMIT
EST3 offers a wide selection of cabinets allowing the greatest use of its flex-ible modular design. From the elegant contoured door design of the Lobby Enclosure through to the standard design of Remote Closet Cabinets, both
aesthetics and function are easily addressed.
Lobby Enclosures
EST3 lobby enclosures provide space for control, monitoring and display modules. Ideal for mounting in lobbies where appearance is important, maximum mounting flexibility is provided with doors that will mount for right- or left-hand opening. Lobby enclosures come in several sizes housing one to three chassis and batteries. Lobby enclosure doors have viewing windows and are available in gray baked enamel or red baked enamel finishes.
3-CAB5(R) Cabinet with Wallbox and door — five LRM spaces Data Sheet E85010-0067
3-CAB7B Wallbox only — one chassis Data Sheet E85010-0067
3-CAB7D(R) Inner and outer doors for 3-CAB7B Data Sheet E85010-0067
3-CAB14B Wallbox only — two chassis Data Sheet E85010-0067
3-CAB14D(R) Inner and outer doors for 3-CAB14B Data Sheet E85010-0067
3-CAB21B Wallbox only — three chassis Data Sheet E85010-0067
3-CAB21D(R) Inner and outer doors for 3-CAB21B Data Sheet E85010-0067
Remote Closet Enclosures
Remote Closet Cabinets provide an economical way of installing equipment in loca-tions where aesthetics are not paramount, such as electrical closets. Optional display modules used for system diagnostics display can be mounted behind the front door. Remote Closet Cabinets are surface mounted and come in sizes providing space for one to three chassis, with room for standby batteries. Remote Closet Cabinets have left hand hinged doors and are available with red finish only. RCC cabinets can also be used as remote battery cabinets.
3-RCC7R Red wallbox and door (one chassis) Data Sheet E85010-0067
3-RCC14R Red wallbox and door (two chassis) Data Sheet E85010-0067
3-RCC21R Red wallbox and door (three chassis) Data Sheet E85010-0067
Chassis Assemblies
3-CHASS4 Provides space for 3-REMICA and four local rail modules Data Sheet E85010-0067
3-CHAS7 Provides space for seven local rail modules Data Sheet E85010-0067
Cabinet Accessories
3-BATS Battery Shelf for RCC Enclosures. Room for up to one 65 AH battery. Data Sheet E85010-0067
3-TAMP Tamper switch for 3-CAB7, 3-CAB14 and 3-CAB21 cabinets Data Sheet E85010-0067
3-TAMP5 Tamper switch for 3-CAB5 Data Sheet E85010-0067
3-TAMPRCC 3-TAMPRCC Tamper Switch for RCC series cabinets. Data Sheet E85010-0067
ATCK Attack rated door for 3-RCC7R Data Sheet E85010-0067
3-RCCEQ50 Seismic battery hold-down for 3-RCC1XXR series. Data Sheet E85010-0067
3-RCCEQ65 Seismic battery hold-down. Supports two 65 Ah batteries. Data Sheet E85010-0067
3-FTEQ Seismic hardening kit for 3-ASU/FT or 3-FTCU telephone handset. Data Sheet E85010-0067
3-CABEQ Seismic battery hold-down for 3-CAB 7, 14 or 21. Data Sheet E85010-0067
Cabinets & Chassis
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
21
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
EST3’s Signature Series intelligent analog-addressable system is an entire family of life safety detec-tors as well as mounting bases, multiple-function input and output modules, and user-friendly maintenance and service tools.
Signature Series detectors continually monitor the protected space with their on-board sensors, which are finely tuned to detect the characteristic properties of combustion. Detection data is gathered and run through sophisticated algorithms that track the sensor readings over time to known signatures of fires. Only when a match is found will an alarm condition occur. This means that a Signature Series detector can distinguish between a harmless puff of dust and a wisp of smoke; between hot, humid weather and a serious life safety condition.
On-board processing and distributed intelligence also results in advanced features that save time and money...
Self-diagnostics and History Log – Signature Series devices constantly run self-checks to provide important maintenance information. The results of these checks are automatically updated and permanently stored in the device’s non-volatile memory.
Automatic Device Mapping – The Signature Loop Con-troller learns where each device’s serial number address is installed relative to other devices on the circuit. This map-ping function is invaluable for tracking down unexpected or missing device addresses, or finding changes to wiring. The System Definition Utility program also uses this map-ping feature to produce system layout or As-Built drawings showing such details as banch wiring (T-taps), device types and their addresses.
Fast Stable Communication – Built-in intelligence means less information needs to be sent between the device and the Signature Loop Controller, making the circuit less sensi-tive to noise and wire characteristics. This renders shielded wiring unnecessary. In fact, existing wiring can be used by Signature Series devices in most retrofit situations.
Testing & Maintenance – Each detector automatically identifies when it is dirty or defective and causes a “dirty de-tector” message. The detector’s sensitiv ity measurement can also be transmitted to the loop controller. A sensitivity report may be printed to satisfy NFPA sensitivity mea surements. The user-friendly maintenance program shows the current state of each detector and other pertinent messages. When the CO sensor’s electrochemical cell reaches its end of life, the detector signals a trouble condition to the control panel.
Signature Series
Intelligent Analog Initiating Devices
Signature Driver Controllers
3-SSDC1 and 3-SDDC1 Signature Driver Controller modules provide an intelligent interface between the 3-CPU3 module and Signature Series devices. The 3-SSDC1 Single Signature Driver Controller module supports one Signature Data circuit, while the 3-SDDC1 Signature Dual Driver Controller module supports two Signature circuits. Both modules occupy one rail space in the fire alarm control cabinet and provide removable field wiring terminals to aid installation. Class B, Class A and Class X wiring are supported. Loop distances over 11,000 feet (3300m) are possible.
CO, Smoke and Heat Detectors p. 22
Fire Detectors p. 23
Duct Detectors p. 23
Detector Bases p. 24
Detector Accessories p. 25
Input/Output Modules p. 26
Pull Stations p. 32
TB1
3-SDDC1SIGNATURE
DRIVERCONTROLLER
MODULE
DUAL
TB2
Circuit# 1
To TB1 on 3-SDDC1 Module
12 435 67 89 10
++
Circuit# 2
To TB2 on 3-SDDC1 Module
12 435 67 89 10
+ +
Class A Configuration Shown (Typical)
SDC #1 Smoke Power
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
22
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Intelligent Carbon Monoxide (CO) Detector
The SIGA-COD detects carbon monoxide from any source of combustion and analyzes the sensor data to determine when to initiate a CO-related life safety event.
SIGA-COD Intelligent Carbon Monoxide Detector Data Sheet E85001-0648
Intelligent Multisensor Optical Smoke Detector with CO Sensor
Includes an optical smoke sensor and a carbon monoxide sensor. The detector analyzes the smoke sensor indepen-dently from the CO sensor, and can report a smoke/fire alarm separate from a CO-related life safety alarm.
SIGA-PCD Intelligent Multisensor Smoke and CO Detector Data Sheet E85001-0651
Intelligent Multisensor Optical Smoke Detector with Heat and CO Sensors
Includes a photoelectric smoke sensor, a fixed-temperature heat sensor, and a carbon monoxide sensor. The detector analyzes the smoke and heat sensors independently from the CO sensor, and can report a smoke/fire alarm separate from a CO-related life safety alarm.
SIGA-PHCD Intelligent Multisensor Smoke, Heat, and CO Detector Data Sheet E85001-0649
Carbon Monoxide and Fire DetectorsIn addition to integrated smoke and heat sensors, Signature Series combination life
safety devices include electrochemical carbon dioxide sensors. CO detection has
rapidly become a standard part of life safety strate gies. Monitored CO detection is
becoming mandated with increasing frequency in all types of commercial applications,
but particularly in occupancies such as hotels, rooming houses, dormitories, day care
facilities, schools, hospitals, assisted living facilities, and nursing homes. In fact, more
than half of the U.S. population already lives in states requiring the installation of CO
detectors in some commercial occupancies. Car bon monoxide is the leading cause of
accidental poisoning deaths in America. Known as the “Silent Killer,” CO is odorless,
tasteless, and colorless. It annually claims nearly 500 lives, and results in more than
15,000 hospital visits.
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
23
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Fire Detectors
Intelligent Optical Smoke DetectorThe workhorse of modern fire alarm systems, this devices includes a photoelectric smoke sensor to detect smoke.
SIGA-PD Intelligent Optical Smoke Detector Data Sheet E85001-0646
Intelligent Rate-of-rise and Fixed Temperature Heat DetectorIncludes a rate-of-rise and a fixed-temperature sensor to detect heat from fire.
SIGA-HRD Intelligent fixed temperature/Rate-of-rise heat detector Data Sheet E85001-0647
Intelligent Multisensor Optical Smoke and Heat DetectorContains a fixed-temperature heat sensor to detect heat from fire and a photoelectric smoke sensor to detect smoke. Unlike simple multi-criteria detectors, the SIGA-PHD can report the heat and photo elements as separate event types — or together. This permits the photo element of the detector to report, for example, a supervisory event during the day, and an alarm event at night – while the heat element always reports an alarm.
SIGA-PHD Intelligent Multisensor Smoke and Heat Detector Data Sheet E85001-0650
Duct Smoke Detectors
SuperDuct Detectors
Less than two inches deep, SuperDuct intelligent smoke detectors are ideal for installation in ductwork, where space is always at a premium. Offering the most advanced and most reliable performance in its class, SuperDuct represents the perfect balance of practical design and advanced technology.
SuperDuct detectors feature a unique design that speeds installation and simplifies maintenance. Removable dust filters, conformally coated circuit boards, and optional water-resistant gaskets keep contaminants away from components, ensuring years of trouble-free service. When cleaning is required, the assemblies come apart easily and snap back together in seconds.
Return
air
Duct smoke
detector
Supply
air
Duct smoke
detector
Remote
test stationFACP
HVAC
unit
Alarm relay output
Alarm relay output
Remote
test station
SIGA-SD Intelligent SuperDuct Detector Data Sheet E85001-0584
SD-PH Protective housing for high humidity environments Data Sheet E85001-0584
Sampling Tubes SD-T8 (8”) SD-T18 (18”) SD-T24 (24”) SD-T36 (36”) SD-T42 (42”) SD-T60 (60”) SD-T78 (78”) SD-T120 (120”)
Remote Test Stations SD-TRM (magnetic) SD-TRM (keyed) SIGA-LED (Remote alarm LED)
Accessories SD-GSK (cover gasket kit) SD-MAG (Test magnet kit) SD-VTK (Air velocity test kit, stoppers only) SIGA-SDPCB (PCB/Signature sensor kit)
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
24
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Audible (Sounder) Bases
Signature Series Sounder Bases add audible output functions to Signature Series smoke and CO detectors. Bases can operate as independent local alarms, or as part of a zone or system alarm with synchronized audible output. The SIGA-AB4G-LF is UL listed for sleeping areas and other applications requiring 520 Hz low frequency audible tones.
SIGA-AB4G-LF Low Frequency Audible (Sounder) Base for CO and Fire Detectors Data Sheet E85001-0640
SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors Data Sheet E85001-0640
SIGA-TCDR Temporal Pattern Generator for SIGA-AB4GT, SIGA-AB4G-LF Data Sheet E85001-0640
SIGA-AB4G Audible (Sounder) Base for SIGA-PS Detectors Only Data Sheet E85001-0640
AB4G-SB Surface Box for Audible Bases Data Sheet E85001-0640
Standard Detector Bases
Standard detector bases provide roomside wiring terminals. They mount to North American one-gang box, 3½ or 4-inch octagon boxes, or 4-inch square electric box. Bases for 4-inch square boxes include the SIGA-TS4 Trim Skirt to conceal the electric box and provide a finished appearance.
SIGA-SB SIGA-SB4 (with trim skirt) Standard Detector Base Data Sheet E85001-0245
Isolator Detector Base
Isolator detector bases provide room-side wiring terminals and includes a built-in line fault isolator. Models with integral switches allow the detector to be removed from its base without causing the isolator to operate. Mounts to North American one-gang box, 3½ or 4-inch octagon boxes, or 4-inch square electrical boxes. Bases for 4-inch square boxes include the SIGA-TS4 Trim Skirt to conceal the electrical box and provide a finished appearance.
SIGA-IB SIGA-IB4 (with trim skirt) Isolator Detector Base Data Sheet E85001-0245
Relay Detector Base
This base includes a relay. Normally-open or closed operation is selected during installation. The dry contact is rated for 1 amp (pilot duty) @ 30 Vdc. The relay’s position is supervised to avoid accidentally jarring it out of position. The relay base does not support the SIGA-LED remote LED. It mounts to North Ameri-can one-gang boxes, 3½ or 4-inch octagon boxes, or 4-inch square electrical boxes. Bases for 4-inch square boxes include the SIGA-TS4 Trim Skirt to conceal the electrical box and provide a finished appearance.
SIGA-RB SIGA-RB4 (with trim skirt) Relay Detector Base Data Sheet E85001-0245
Detector Bases
CO system wiring for detector operation of bases
AUX_RISER +AUX_RISER -
SLC +SLC -
3
Sounder
Tone Generator
Listed 24 V EOL
Supervising Equipment
SounderSounder Base UL approved
for sleeping areas!
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
25
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
SIGA-TCDR Temporal Pattern Generator SLC_IN +
AUX_RISER_IN + AUX_RISER_OUT +
A
SLC_OUT +
1 2
From previous device To next device
The SIGA-TCDR Temporal Pattern Generator is an addressable device that generates sound patterns for carbon monoxide (CO) and fire signals for the AB4GT sounder base. The control panel sends synchronization and channel commands to the SIGA-TCDR; the channel selection determines the pattern.
SIGA-TCDR Temporal Pattern Generator for AB4GT Sounder Base Data Sheet E85001-0623
Detector Mounting Plate
The SIGA-DMP Detector Mounting Plate is a 7-inch (178mm) square mounting plate designed to provide convenient mounting of Signature Series intelligent smoke detectors in raised floor or plenum applications. The detector mounting plate may also be installed in low velocity ducts that have a maximum width of up to 36-inches (915mm) and a maximum height of up to 36-inches (915mm).
SIGA-DMP Detector Mounting Plate Data Sheet E85001-0255
Remote LED
The remote LED connects to the SIGA-SB or SIGA-SB4 Standard Base. It features a North American size one-gang plastic faceplate with a white finish and red alarm LED.
SIGA-LED Remote Alarm LED Data Sheet E85001-0245
Trim Skirt
Use the SIGA-TS Trim Skirt to give Signature detectors a finished look and hide surface imperfections around the detector’s base. Supplied with all four-inch detector bases, the SIGA-TS4 can also be ordered separately. Use the black model with SIGA-IPHSB.
SIGA-TS Detector Trim Skirt (white) Data Sheet E85001-0245
SIGA-TSB Detector Trim Skirt (black) Data Sheet E85001-0245
SIGA-TS4 Detector Trim Skirt (white) – for 4-inch box Data Sheet E85001-0245
Detector Accessories
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
26
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Signature Series intelligent input/output modules feature multiple user-set personality codes that define the module’s behavior.
Signature Series input/output modules are extremely flexible and powerful devices that gather analog information from the slave devices connected to them and convert this data into digital signals. They are available in models that mount in standard one- or two-gang electrical boxes, as well as versions that plug into UIO motherboards. The actual function of each module is determined by its installer-selected personality code. This is downloaded to the module from the Signature Loop Controller during system configuration. Because they are intelligent devices, all decisions are made at the module. This allows lower communication speed but very fast control panel response time and less sensitivity to line noise and loop wiring properties. As a result, twisted or shielded wire is not required.
Signature Series
Input/Output Modules
Standard two-gang mount
Plug-in UIOs with motherboard
Application ModuleVoice messages Digital Messaging ModuleWaterflow Switches Waterflow/Tamper ModuleClass A indicating and initiating circuits, two-wire smoke detectors
Universal Class A/B Module
Class B Initiating Circuits: Door Closers, Fans, Dampers
Class B Input Module Monitor ModuleControl Relay Module
Telephone Power and Audible/Visual Signal Power Selector, Strobe Synchronization
Signal Module
Sounder Base power Reversal Relay ModuleFire Suppression Releasing ModuleFault detection Isolator Module
Module mounting and installation options
Signature Series input/output modules are available in models that feature two mounting options: standard mount and plug-in.
Standard mount models are installed to North American two-gang or one-gang electrical boxes, making them ideal for locations where only one module is required. Separate I/O and data loop connections
are made to each module.
Plug-in UIO modules mount to UIO moth-erboards. Two- and six-module UIO
motherboards are available, mak-ing them ideal for installations
where more than one module is required. Motherboards can accommodate individual risers for each on-board module,
or shared risers in any combination with their UIO modules. All wiring connections are made
to terminal blocks on the motherboard. UIO assemblies may be mounted in either cabinets, or standard electrical enclosures.
Standard mount (one- or two-gang)
FIRE ALARM
MODULE
UIO Motherboard
Plug-in (UIO)Module
Cabinet or electrical enclosure
Plug-in UIO
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
27
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Digital Message Module
The SIGA-MDM Digital Message Module provides custom pre-recorded voice messaging. Two standard factory pre-recorded messages are included. Each module can store two 30 second messages in its non-volatile EEPROM memory. A microphone/line-level audio input stereo jack and output stereo jack, as well as record and playback switches are conveniently located on top of the module. Programming in the Signature Data Controller provides all control instructions; extra wiring for monitoring or controlling circuits is not required. Up to 47 modules can be cascaded together. The SIGA-MDM is available as a plug-in module only.
SIGA-MDM Intelligent Digital Message Module Data Sheet E85001-0363
4
3
2
1
4
3
2
1
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
P1 P2
TB1 TB2TB7
TB8 TB9
TB15
PLAY
REC.
LINE
IN
HEAD
PHONES
MSG 1
MSG 2
CLIP
MIC.
LINE
SDC
NORMAL
ACTIVE
PLAY
REC.
LINE
IN
HEAD
PHONES
MSG 1
MSG 2
CLIP
MIC.
LINE
SDC
NORMAL
ACTIVE
IN OUT
Audio Preamp Riser
24 Vdc To
Other Loads
24 Vdc
From Power Supply
First Downstream
Jumper
To Other
SIGA Devices
To Signature
Loop
Controller
(SLC)
_
_
+
+
Universal Class A/B Module
The Universal Class A/B Module is used to connect initiating, appliance, or two-wire smoke circuits in either Class A or Class B configurations. The plug-in version can also be used as a Class A dry contact initiating device circuit. The actual function of this module is determined by the “personality code” selected by the installer. Up to fifteen personalities are available.
SIGA-UM Universal Class A/B Module (Two-gang standard mount) Data Sheet E85001-0275
SIGA-MAB Universal Class A/B UIO (Plug-in) Module Data Sheet E85001-0275
SIGA-UM
Class B Input Module
The Class B Input Module is used to connect Class B normally-open Alarm, Supervisory, or Monitor type dry contact initiating device circuits. The standard-mount version is available with either one or two input connections. The plug-in version accepts two input connections. The actual function of this module is determined by the “personality code” selected by the installer. A total of four personalities are available.
SIGA-CT1 Single Input Module (One-gang standard mount) Data Sheet E85001-0241
SIGA-CT1HT Single Input Module, high temperature rating (One-gang standard mount) Data Sheet E85001-0241
SIGA-CT2 Dual Input Module (One-gang standard mount) Data Sheet E85001-0241
SIGA-MCT2 Dual Input UIO (Plug-in) Module Data Sheet E85001-0241
SIGA-CT1/CT2
SIGA-MCT2
SIGA-MAB
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
28
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Signal ModuleThe Signal Module is used to connect, upon command from the loop controller, supervised Class B signal or telephone circuits to their respective power inputs. Models are available with one or two power inputs. These may be either polarized 24 Vdc to operate audible and visual signal appliances, or 25 and 70Vrms to operate audio evacuation speakers and firefighter’s telephones. The actual function of this module is determined by the “personality code” selected by the installer. A total of three personalities are available.
SIGA-CC1 Single Input Signal Module (Two-gang standard mount) Data Sheet E85001-0237
SIGA-MCC1 Single Input Signal UIO (Plug-in) Module Data Sheet E85001-0237
SIGA-CC2 Dual Input Signal Module (Two-gang standard mount) Data Sheet E85001-0237
SIGA-MCC2 Dual Input Signal UIO (Plug-in) Module Data Sheet E85001-0237
SIGA-CC2A Dual Input Signal Module with Class A Operation (Two-gang mount) Data Sheet E85001-0609
SIGA-MCC2A Dual Input Signal UIO with Class A Operation (Plug-in) Module Data Sheet E85001-0609
Control Relay ModuleThe Control Relay Module provides a Form C dry relay contact to control external appliances such as door closers, fans, dampers etc. This device does not provide supervision of the state of the relay contact. Instead, the on-board microprocessor ensures that the relay is in the proper ON/OFF state. Upon command from the loop controller, the relay activates the normally open or normally-closed contact. This module supports only one personality: no user configuration is required.
SIGA-CR Control Relay Module (One-gang standard mount) Data Sheet E85001-0239
SIGA-MCR Control Relay UIO (Plug-in) Module Data Sheet E85001-0239
SIGA-CRH High Power Control Relay Module (One-gang standard mount) Data Sheet E85001-0644
Polarity Reversal Relay ModuleThe Polarity Reversal Relay Module provides a Form C dry relay contact to power and activate a series of SIGA-AB4 Audible Sounder Bases. Upon command from the Signature loop controller, the SIGA-CRR reverses the polarity of its 24 Vdc output, thus activating all Sounder Bases on the data loop. This module supports only one personality: no user configuration is required.
SIGA-CRR Polarity Reversal Relay Module (One-gang standard mount) Data Sheet E85001-0239
SIGA-MCRR Polarity Reversal Relay UIO (Plug-in) Module Data Sheet E85001-0239
Riser Monitor ModuleThe SIGA-RM1 Riser Monitor Module is an intelligent device that monitors the integrity of 24 Vdc, 25 Vac, and 70 Vac circuits, as well as telephone riser signals. Upon the loss of a signal, the Riser Monitor Module causes the fire alarm control panel to indicate an alert status. Per-sonality codes downloaded to the Riser Monitor Module during system configuration determine its function.
SIGA-RM1 Riser Monitor Module (One-gang standard mount) Data Sheet E85001-0535
SIGA-MRM1 Riser UIO (Plug-in) Module Data Sheet E85001-0535
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
29
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Synchronization Output Module
The Synchronization Output Module is an intelligent device that connects a supervised output circuit to a 24 Vdc riser. The output wiring is monitored for open circuits and short circuits. A short circuit will cause the fire alarm control panel to inhibit the activation of the audible/visual signal circuit so the riser is not connected to the wiring fault. Upon command from the Signature loop controller, the Auto-Sync Output Module connects the output circuit to the riser input. The output circuit operates polarized audible and visual appliances that have an adjustable resynchronizing feature.
SIGA-CC1S Synchronization Output Module (One-gang standard mount) Data Sheet E85001-0543
SIGA-MCC1S Synchronization Output UIO (Plug-in) Module Data Sheet E85001-0543
Input/Output Module
The Input/Output Module is an intel l igent device that provides the fol lowing modes of operation:
• Output with monitor input• Input/programmable output• Input/direct output
SIGA-IO Input/Output Module (One-gang standard mount) Data Sheet E85001-0533
SIGA-MIO Input/Output UIO (Plug-in) Module Data Sheet E85001-0533
Waterflow/Tamper Module
The SIGA-WTM Waterflow/Tamper Module is a two circuit intelligent module. Circuit 1 is for Class B normally-open waterflow alarm switches. When the input contact is closed for approximately 16 seconds, an “alarm” signal is sent to the loop controller. Circuit 2 is for Class B normally open dry contact supervisory and tamper switches. When the input contact is closed, an “active” signal is sent to the loop controller. Conditions on both circuits are latched at the module.
SIGA-WTM Waterflow/Tamper Module (One-gang standard mount) Data Sheet E85001-0297
Isolator Module
The SIGA-IM Isolator Module is an intelligent device that allows part of the Signature data loop to continue operating in the event of a short circuit. The module can be wired into a Class A data loop at any point. A maximum of 96 isolator modules can be installed on one circuit. If a fault occurs, the isolator cuts power to all devices beyond the isolator on the loop. Once activated, the line fault isolator continuously checks the faulted side of the loop to determine if the short still exists. When the fault is cleared, the module automatically restores the entire data loop to its normal condition.
SIGA-IM Fault Isolator Module (Two-gang standard mount) Data Sheet E85001-0271
Monitor Module
The SIGA-MM1 is a single-circuit intelligent module that includes a Class B normally-open dry contact. This is used for monitoring input from devices such as fans, dampers, and doors. When the input contact is closed, an “active” signal is sent to the loop controller. The active condition is not latched at the module.
SIGA-MM1 Monitor Module (One-gang standard mount) Data Sheet E85001-0297
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
30
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Related Equipment
MFC-A Multi-function Cabinet (for UIO and Releasing modules)
27193-11 Surface Mount Box - Red, One-gang
27193-16 Surface Mount Box - White, One-gang
27193-21 Surface Mount Box - Red, Two-gang
27193-26 Surface Mount Box - White, Two-gang
235196P Bi-polar Transient Protector (use with all Signal Modules)
SIGA-MP1 Signature Module Mounting Plate, 1 footprint
SIGA-MP2 Signature Module Mounting Plate, 1/2 footprint
SIGA-MP2L Signature Module Mounting Plate, 1/2 extended footprint
Riser 2 Input
common to
all SIGA-UIO
Modules
Jumpers Connect
Riser Input #1
Between Modules
Individual Riser 1 Input to each SIGA-UIO module
Module Input/Output Wiring
Signature
Data
Circuit
Data In
Data Out
Universal Input/Output (UIO) Motherboards
Signature Series Universal Input/Output Module Motherboards provide mounting and wiring terminations for up to six Signature Series plug-in UIO (SIGA-“M” se-ries) modules. UIO motherboards snap into a rigid extruded track (included) with mounting pads for convenient mounting into a variety of equipment enclosures. UIO modules plug into the board and are held securely in place with captive machine screws. All field wiring connects to terminal blocks on the motherboard, which permits rapid removal and replacement of modules for troubleshooting.
The SIGA-UIO2R provides mounting and wiring terminations for up to two UIO modules, and the SIGA-UIO6R provides mounting and wiring terminations for up to six UIO modules. Both motherboards feature a riser #1 input and a riser #2 input bus. Jumpers on riser #1 input (between modules), facilitate sharing a single riser among more than one module. This significantly reduces wiring requirements. Re-moving the jumpers provides
separate riser inputs to each adjacent module. Riser #2 input is fixed to each module position and cannot be split.
The SIGA-UIO6 provides mounting and wiring terminations for up to six UIO modules. This moth-erboard provides two riser inputs that are common to all modules.
UIO motherboards mount inside the MFC-A cabinet or other suitable UL-listed electrical enclosure. Each MFC-A will hold one UIO2R motherboard or one UIO6 or UIO6R motherboard complete with their full complement of modules.
SIGA-UIO2R Universal Input/Output Module Board with Riser Inputs — 2 Module Positions Data Sheet E85001-0365
SIGA-UIO6R Universal Input/Output Module Board with Riser Inputs — 6 Module Positions Data Sheet E85001-0365
SIGA-UIO6 Universal Input/Output Module Board — 6 Module Positions Data Sheet E85001-0365
UIO6R
UIO2R
SUBMIT
Notification
Appliances
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
Initia
ting
D
evices
31
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
Releasing Module
The Signature Series Releasing Module (SIGA-REL) is an analog addressable module that works with fire suppression systems designed to release extinguish-ing gas. Its primary function is the control of sprinkler pre-action routines and the initiation of suppression system deluge functions. The module is easily configured in the field and offers a wide range of options that prevent the unnecessary release of extinguishing agent.
The SIGA-REL is a network component consisting of:• Two supervised release circuits• Two supervised pre-release circuits• One supervised manual
release input circuit• One supervised abort cir-
cuit for N/O abort switch• One first alarm output
relay (Form C Contact)
The releasing module includes a built-in timer that inhibits the deluge function during the pre-action routine. One of four pre-action routines, may be selected by means of dip-switches on the module. The duration of automatic and manual time delays, as well as the abort time settings are also selectable with dip-switches. The SIGA-REL mounts inside an MFC-A cabinet or other suitable UL-listed electrical enclosure. Each MFC-A will hold one SIGA-REL.
Available releasing module accessories include dedicated pull sta-tions, abort switches and service switches. Together with the SIGA-REL, they comprise a complete fire suppression package.
SIGA-REL Analog addressable releasing module Data Sheet E85001-0531
RELA-ABT Abort station Data Sheet E85001-0531
RELA-SRV Service disconnect station Data Sheet E85001-0531
276A-REL Manual releasing station (single-action) Data Sheet E85001-0531
278A-REL Manual releasing station (double-action) Data Sheet E85001-0531
RELA-EOL Polarized end-of-line relay Data Sheet E85001-0531
Abort
Manual Release
TB3 TB2
TB6
TB4 TB5
TB1
SW1-SW8
First alarm output
Form C 3 A @24 Vdc
Signature data in
Signature data out
+_
+_
Release CCT1
+
_
24 Vdc in
24 Vdc out
Pre-release CCT2 (steady)
Pre-release CCT1 (pulsed 15/60)
SIGA-REL
+
_
1
2
3
4
RELA-EOL
1
2
3
4
RELA-EOL
Release CCT2
+_
+_
+_
+_
DS1
DS2
DS4DS3DS5
DS6 DS7
Init
iati
ng
D
evic
es
SUBMIT
ES
T3
Net
wor
k
32
EST3 I n t e l l i g e n t I n i t i a t i n g D e v i c e s
LIFT
NORMAL
8
4
7
3 2 1
DATA OUT (+)DATA IN (+)
DATA OUT (-)DATA IN (-)
To Next DeviceFrom Signature Controlleror Previous Device
Green LED(Normal)
Red LED(Alarm/Active)
REAR VIEW
TB1
TB2
8
4
7
3 2 1
DATA OUT (+)DATA IN (+)
DATA OUT (-)DATA IN (-)
To Next DeviceFrom Signature Controlleror Previous Device
Green LED(Normal)
Red LED(Alarm/Active)
REAR VIEW
TB1
TB2
Single Action Pull Stations
SIGA-270 series manual pull stations are made from die-cast zinc and finished with red epoxy powder-coat paint. With positive pull-lever operation, one pull on the station handle breaks the rod and turns in a positive alarm. Where two-stage operation is re-quired, SIGA-270P pre-signal models are equipped with a general alarm (GA) keyswitch.
SIGA-270 One Stage Fire Alarm Station, English Markings Data Sheet E85001-0279
SIGA-270P Two Stage (Pre-signal) Fire Alarm Station, English Markings Data Sheet E85001-0279
276-K2 GA Key — for pre-signal station Data Sheet E85001-0279
270-GLR 20 Break-rods — for SIGA-270 series Data Sheet E85001-0279
276B-RSB Surface Mount Box, Red — for SIGA-270 series Data Sheet E85001-0279
Double Action Pull Stations
The double action, single stage SIGA-278 station is a contemporary style manual station made from durable red LEXAN. To initiate an alarm, first lift the upper door, then pull the alarm handle.
SIGA-278 Double Action (One Stage) Fire Alarm Station, English Markings Data Sheet E85001-0279
276B-RSB Surface Mount Box, Red — for SIGA-278 series Data Sheet E85001-0279
276-GLR 20 Break-rods — for SIGA-278 series Data Sheet E85001-0279
Manual Pull Stations
Manual Station Relocator
The Manual Station Relocator is designed to lower the height of a fire alarm pull station to meet ADA requirements. Most existing pull stations are mounted 60 inches (1524mm) or higher above the floor. The Relocator lowers the height to 48 inches (1220mm) without the need for pulling new wires or moving the existing electrical box.
RR-32RL Pull Station Relocator Data Sheet E85001-0351
Stopper II
This unique device helps prevent false alarms without restricting legitimate ones. It consists of a tamper-proof clear LEXAN polycarbonate shield and frame that fits easily over manual pull stations. When lifted, it sounds a piercing warning horn.
STI-1100 (Flush) STI-1130 (Surface) Stopper II with Horn Data Sheet E85001-0491
STI-1200 (Flush) STI-1230 (Surface) Stopper II without Horn Data Sheet E85001-0491
STI-3100 (2" Spacer) STI-3004 (Conduit Insert) Spacers Data Sheet E85001-0491
STI-3002 (Gasket) STI-3003 (Conduit Gasket) Weatherproofing Data Sheet E85001-0491
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
33
No
tific
atio
n A
pp
liances
Class B Notification Appliance Circuit with Genesis Signalsand Signal Master for independent sounder and strobecontrol and synchronisation
Notification Appliance CircuitClass B with separate strobe and horn circuits
Notification Appliance CircuitClass A with combination horn-strobe circuit
Notification AppliancesEDWARDS notification appliances are high-performance devices finely
tuned to deliver maximum output in exchange for the lowest possible cur-
rent draw. Covering the entire spectrum of life safety applications, these
devices are durable, dependable, and virtually maintenance-free. And they
support a wide range of mounting options that make them ideal for new
construction and retrofit applications alike.
Field Wiring
Notification appliances may be configured
for Class A or Class B wiring. Genesis
combination horn-strobes, when used
with the innovative Signal Master Module,
support independent horn control over
a single pair of wires and precision
synchronization that exceeds UL
requirements. This reduces wiring time while
meeting the requirements of even the most
demanding application.
Wall Strobes, Horns & Chimes p. 35
Low Frequency Horns and Horn-Strobes p. 36
Ceiling Horns & Horn-Strobes p. 36
Outdoor Horns & Strobes p. 37
Wall Speakers & Speaker-Strobes p. 38
Ceiling Speakers, Horns & Strobes p. 39
Outdoor Speakers & Strobes p. 40
High Power Speaker Arrays p. 41
LED Strobes and Horn-Strobes p. 41
Medium Power Speaker Arrays p. 42
Firefighters’ Telephones p. 43
Harsh Environment Signals p. 44
Audible Signals p. 45
Accessories p. 46
All appliances feature #18 - #12 AWG terminals – ideal for long runs, existing wiring
SP
KR
S+
C S-
Polarity shown in
alarm condition
To next device
or end of line
device
++
SP
KR
S+
C S-
S S
+ +
To listed fire alarm control panel(supervised signal circuit
– 20-24 Vdc)
To listed fire alarm control panel(supervised amplifier signal circuit
– 25.2 or 70.7V rms)
Device Wiring, Speaker-strobes Device Wiring, Horn-strobes
Strobe Syncrhonization
On a common circuit, strobes flash once per second (1
fps) within 10 milliseconds over a two-hour time period. A
synchronization source is required to comply with UL 1971
synchronization standards. Temporal setting (private mode
only): synchronized to temporal output on the same circuit.
Syncrhonization Sources
The following control panels, power supplies, and modules
provide synchronization sources that enable Genesis strobe
devices to comply with UL 1971 synchronization standards:
SIGA-CC1S, SIGA-MCC1S, SIGA-CC2A, SIGA-MCC2A,
G1M-RM, BPS6A, BPS10A, APS6A, APS10A, EST3X, iO
Series, Fireshield Plus.
EST3N o t i fi c a t i o n A p p l i a n c e s
34
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
Genesis Visual & Audible Signals
The award-winning Genesis line of products represents
excellence in fire alarm notification with looks, features, and
performance benefits designed with your project in mind.
Wall strobes, horns, and chimes about the size of a deck
of playing cards offer a discreet alternative to bulky devices,
while speakers and ceiling models with clean modern lines
blend inconspicuously with their surroundings.
Signaling on-demand
Though designed for discretion, Genesis signals are also
engineered to command attention. Wall-penetrating high
dB output and patented FullLight strobe technology im-
merse the protected area with levels of light and sound
that simply can’t be ignored – all in exchange for the low-
est current demands of any device in their class.
Genesis brings on-demand signaling to every applica-
tion with an unparalleled range of field-configurable
options: horns and chimes with high/low dB output
settings; speakers with multiple wattage tap selections;
and strobes with selectable candela output and flash
rate – options that put you in the driver’s seat when time
is short, budgets slim, and manpower at a premium. It
also means fewer parts to stock, less inventory to worry
about, and the flexibility to meet changing demands – on
the fly – without having to reinstall equipment or order
more parts!
Application flexibility
Whether you’re designing for a new landmark structure,
or simply retrofitting a local strip mall, competitively-
priced Genesis signals bring value, good looks, and
installation flexibility to every application. Contact Ed-
wards today to learn how your signal solutions can be
the model of discretion.
A complete line engineered to deliver innovative features and superb output.
Wall Strobes, Horns, Chimes, p. 35
Low Frequency Horns and Horn-Strobes, p. 36
Ceiling Horns, Horn-Strobes, p. 36
Outdoor Horns, Horn-Strobes, p. 37
Wall Speakers and Speaker-strobes, p. 38
Ceiling Speakers, Speaker-strobes, p. 39
Outdoor Speakers, Speaker-Strobes, p. 40
LED Strobes and Horn-Strobes, p. 41
EST3N o t i fi c a t i o n A p p l i a n c e s
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
35
No
tific
atio
n A
pp
liances
Genesis G1 Series
Wall Strobes, Horns & Chimes
EST3N o t i fi c a t i o n A p p l i a n c e s
SUBMIT
Genesis signals feature textured housings in architecturally neutral white or traditional fire red. An ingenious iconographic symbol indicates the purpose of the device. This universal symbol is code-compliant and is easily recog-nized by all building occupants regardless of what language they speak. models with “FIRE” and “ALERT” markings are also available.
Genesis strobes offer 15 to 110 candela output, which is selectable with a conveniently-located switch on the side of the device. The candela output setting remains clearly visible even after final installation, yet it stays locked in place to prevent unauthorized tampering. (Data Sheet E85001-0573)
White housing White housing Red housing Red housing Fire Alarm Appliances no marking with “FIRE” no marking with “FIRE” (with “Running Man” icon)
G1-VM G1F-VM G1R-VM G1RF-VM Strobe only (15/30/75/110 cd)
G1F-V1575 G1RF-V1575 Strobe only (15/75 cd¹), 24 V
Genesis Horns and Horn-strobes reach output levels as high as 99 dB and features a unique multiple frequency tone that results in excellent wall penetration and an unmistakable warning of danger. Horns may be configured for either coded or non-coded signal circuits. They can also be set for low dB output with a jumper cut that reduces horn output by about 5 dB. (Data Sheet E85001-0573)
White housing White housing Red housing Red housing Fire Alarm Appliances no marking with “FIRE” no marking with “FIRE” (with “Running Man” icon)
G1-HD G1F-HD G1R-HD G1RF-HD Horn only (high/low dB)
G1-HDVM G1F-HDVM G1R-HDVM G1RF-HDVM Horn-strobe (15/30/75/110, high/low dB)
G1F-HDV1575 G1RF-HDV1575 Horn-strobe (15/75 cd¹, high/low dB), 24 V
G1-P G1F-P G1R-P G1RF-P Steady horn (not compatible with Signal Master)
Genesis mass notification appliances bring the same high-performance fire alarm features and unobtrusive design to mass notification applications. Available with amber lenses and optional “ALERT” housing labels, they are ideal for applica-tions that require differentiation between fire alarm and mass notification alerts. (Data Sheet E85001-0573)
White housing White housing Mass Notification Appliances no marking with “ALERT” (with no “Running Man” icon)
G1WN-VMA G1WA-VMA Strobe only, amber lens (A/B/C/D cd settings)
G1WN-VMC G1WA-VMC Strobe only, clear lens (15/30/75/110 cd)
Genesis chimes and chime-strobes produce a pleasing mellow tone. When steady (non-stroked) voltage is applied, the chime automatically pulses at 60 strokes per minute, or may be field-configured for temporal output. When installed with a GIM Signal Master Module, the chime may also be field-configured for coded operation, which enables the chime output to match the rate that voltage is applied to the circuit. Chimes may be set for low dB output with a jumper cut that reduces sound output by about 5 dB. (Data Sheet E85001-0574)
White housing Red housing Chimes and Chime-strobes
G1-CVM G1R-CVM Chime-strobe (15/30/75/110, high/low dB)
G1-C G1R-C Chime only (high/low dB)
Trim plates for wall horns, chimes, and strobes are ideal for covering openings left behind during retrofits.
White plate White plate Red plate Red plate White plateFire Trim Plates no marking with “FIRE” no “FIRE” with “FIRE” with “ALERT”
G1T G1T-FIRE G1RT G1RT-FIRE G1WT-ALERT Trim plate for 2-gang or 4” boxes
¹ 15/75 cd models provide fixed output. The 15 cd output component complies with UL1971. The 75 cd output component complies with UL 1638.
36
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Genesis G4LF Series Wall Models
Low Frequency (520 Hz) Horns and Horn-Strobes
G4LF Series notification appliances provide the benefits of Genesis life safety signals with output suitable for sleeping areas and other applications requiring low frequency audible tones. These high-performance appliances generate a crisp 520 Hz tone in the standard 3-3 tem-poral pattern. An optional setting configures the appliance for continuous audible output — a critical feature for notification appliance circuits that are coded with a CDR-3 coder module. All G4LF appliances feature field-configurable high and low dB output settings. Horn-Strobe models feature field-selectable 15, 30, or 75 cd output settings.
G4LFWN-HVM Horn-Strobe, 520 Hz, White Housing, No Marking, 15/30/75 cd Data Sheet E85001-0639
G4LFWF-HVM Horn-Strobe, 520 Hz, White Housing, FIRE Marking, 15/30/75 cd Data Sheet E85001-0639
G4LFRN-HVM Horn-Strobe, 520 Hz, Red Housing, No Marking, 15/30/75 cd Data Sheet E85001-0639
G4LFRF-HVM Horn-Strobe, 520 Hz, Red Housing, FIRE Marking, 15/30/75 cd Data Sheet E85001-0639
G4LFWN-H Horn, 520 Hz, White Housing, No Marking Data Sheet E85001-0639
G4LFWF-H Horn, 520 Hz, White Housing, FIRE Marking Data Sheet E85001-0639
G4LFRN-H Horn, 520 Hz, Red Housing, No Marking Data Sheet E85001-0639
G4LFRF-H Horn, 520 Hz, Red Housing, FIRE Marking Data Sheet E85001-0639
Genesis GC Series Ceiling Models
Strobes and Horn-StrobesGenesis ceiling strobes are available in low- or high-candela output models featuring 15 to 95, or 95 to 177 cd output. The setting is selectable with a conveniently-located switch that remains clearly visible even after final installation, yet it is locked in place to prevent unauthorized movement after installation.
Genesis horn output reaches as high as 99 dB (peak) and features a unique multiple frequency tone that results in excellent wall penetration. Horns may be set for low dB output with a jumper cut that reduces horn output by about 5 dB.
All models are rated for both wall and ceiling installation.
Fire Alarm Appliances
All fire alarm appliances come White housing White housing Red housing with the “Running Man” Icon no marking with “FIRE” with “FIRE”
Strobe, 15/30/75/110 (standard output) cd, selectable GC-VM GCF-VM GCFR-VM
Strobe, 95/115/150/177 (high output) cd, selectable GC-VMH GCF-VMH
Horn-strobe, 15/30/75/110 (standard output) cd, selectable GC-HDVM GCF-HDVM GCFR-HDVM
Horn-strobe, 95/115/150/177 (high output) cd, selectable GC-HDVMH GCF-HDVMH
Mass Notification Appliances
White housings Clear lens Clear lens Amber lens Amber lens No “Running Man” Icon no marking with “ALERT” no marking with “ALERT”
Strobe, four standard cd settings GCWN-VMC GCWA-VMC GCWN-VMA GCWA-VMA
Strobe, four high output cd settings GCWN-VMHC GCWA-VMHC GCWN-VMHA GCWA-VMHA
Ceiling Strobes Data Sheet E85001-0557
Ceiling Horn-strobes Data Sheet E85001-0559
UL compliant signals for sleeping
areas!
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
37
No
tific
atio
n A
pp
liances
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Genesis WG4 Series Wall Models
Weatherproof Horns and Horn-StrobesGenesis WG4 Series horns and horn-strobes are among the most versatile emer-gency signals of their kind. Rated for indoor or outdoor use, they are suitable for a wide range of wet and harsh environments with a listed operating temperature range of as low as -31°F to as high as 151°F (-35°C to 66°C).
Refer to Data Sheet E85001-0628 -- Genesis Outdoor Horns and Strobes for details.
Field Configuration
Genesis WG4 strobes feature four selectable light output set-tings. Cd selections are changed by removing the cover and simply sliding the switches to the desired setting, which remains visible through a small window on the front of the device after the cover is replaced. Genesis Horn-strobes may also be configured for high or low dB output and temporal flash. This battery-saving feature is intended for private mode signaling only.
WG4RF-H WG4RF-HVMC WG4WF-H WG4WF-HVMC WG4RN-H WG4RN-HVMC WG4WN-H WG4WN-HVMC
Light Output
Standard Candela Horn-strobes
Standard/ratingStrobe Switch Position
D C B AUL 1971 Indoor 15 cd 29 cd 70 cd 87 cdUL 1638 Outdoor @ -35°C 6 cd 12 cd 28 cd 35 cdCAN/ULC-S526 Outdoor @ -40°C 1 cd 3 cd 8 cd 10 cd
High Candela Horn-strobes
Standard/ratingStrobe Switch Position
D C B AUL 1971 Indoor 102cd 123cd 147cd 161cdUL 1638 Outdoor @ -35°C 41cd 50 cd 60 cd 65 cdCAN/ULC-S526 Outdoor @ -40°C 11 cd 14 cd 17 cd 18 cd
White housing White housing Red housing Red housing Outdoor Fire Alarm Appliances no marking with “FIRE” no marking with “FIRE”
WG4WN-H WG4WF-H WG4RN-H WG4RF-H Horn Only
WG4WN-HVMC WG4WF-HVMC WG4RN-HVMC WG4RF-HVMC Horn-Strobe, standard cd output
WG4WN-HVMHC WG4WF-HVMHC WG4RN-HVMHC WG4RF-HVMHC Horn Only, high cd output
WG4 Mounting Accessories
WG4WTS (white) WG4RTS (red) Surface Skirt for Genesis WG4 Appliances
74347U (white) 449 (red) Surface mount box, outdoor rated
WG4GSKT Genesis WG4 Full Body Mounting Gasket for Smooth Surfaces
For Audible Sounder Bases, see Intelligent Initiating Devices.
Signal In —
Signal In +
Signal Out —
Signal Out +
—/+ designations indicate the signal polarity required to activate the device.
38
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Genesis speakers combine high performance output with a low profile design to deliver a life safety audio solution that’s as versatile as it is effective. Protruding no more than one inch from the wall, these appliances blend inconspicuously with any decor. All speak-ers feature selectable ¼, ½, 1, or 2 watt operation.
Speaker-strobes feature field-configurable candela output, select-able with a conveniently-located switch on the bottom of the device.
Candela and wattage settings remain clearly visible even after final installation.
Genesis G4 Series Wall Models
Speakers and Speaker-strobes
Speakers and speaker-strobes (Data Sheet E85001-0642)
White housing White housing Red housing Red housing Fire Alarm Speakers no marking with “FIRE” no marking with “FIRE” (with “Running Man” icon)
G4-S2 G4F-S2 G4R-S2 G4RF-S2 25 V Speaker
G4-S7 G4F-S7 G4R-S7 G4RF-S7 70 V Speaker
G4-S2VM G4F-S2VM G4R-S2VM G4RF-S2VM 25 V Speaker-strobe (15/30/75/110 cd settings)
G4-S7VM G4F-S7VM G4R-S7VM 70 V Speaker-strobe (15/30/75/110 cd settings)
G4F-S7V1575 G4RF-S7V1575 70 V Speaker (15/75 cd)
High fidelity speakers and speaker-strobes meet new standards for audible tones in sleeping areas and produce crisp, clear voice audio output that is highly intelligible over large areas. (Data Sheet E85001-0642)
White housing White housing Red housing Red housing Fire Alarm Speakers no marking with “FIRE” no marking with “FIRE” (no “Running Man” icon)
G4HFN-S2 G4HFWF-S2 G4HFRN-S2 G4HFRF-S2 25 V Speaker
G4HFN-S7 G4HFWF-S7 G4HFRN-S7 G4HFRF-S7 70 V Speaker
G4HFN-S2VM G4HFWF-S2VM G4HFRN-S2VM G4HFRF-S2VM 25 V Speaker-strobe (15/30/75/110 cd settings)
G4HFN-S7VM G4HFWF-S7VM G4HFRN-S7VM G4HFRF-S7VM 70 V Speaker-strobe (15/30/75/110 cd settings)
High fidelity mass notification speakers and speaker-strobes feature optional amber lenses and “ALERT” lettering on white housings, and meet new standards for audible tones in sleeping areas. (Data Sheet E85001-0642)
Clear lens Amber lens Amber lens High Fidelity Mass Notification Speakers “ALERT” no marking “ALERT” — white housing, no “Running Man icon”
G4HFWA-S2VMC G4HFWN-S2VMA G4HFWA-S2VMA 25 V Speaker-strobe (A/B/C/D cd settings)
G4HFWA-S7VMC G4HFWN-S7VMA G4HFWA-S7VMA 70 V Speaker-strobe (A/B/C/D cd settings)
Speaker only models: G4HFWA-S2 (25 V, “ALERT” marking) G4HFWA-S7 (70 V, “ALERT” marking)
Mass notification speakers and speaker-strobes feature amber lenses and optional “ALERT” lettering. They are ideal for applications that require differentiation between fire alarm and mass notification alerts. (Data Sheet E85001-0642)
Clear lens Clear lens Amber lens Amber lens Mass Notification Speakers no marking “ALERT” no marking “ALERT” — white housing, no “Running Man” icon
G4WN-S2VMC G4WA-S2VMC G4WN-S2VMA G4WA-S2VMA 25 V Speaker-strobe (A/B/C/D cd settings)
G4WN-S7VMC G4WA-S7VMC G4WN-S7VMA G4WA-S7VMA 70 V Speaker-strobe (A/B/C/D cd settings)
G4EWN-C G4EWF-C G4EWN-A G4EWA-A Mass notification expander, white
G4ERN-A G4ERA-A Mass notification expander, red
Speaker-only models, 25 V: G4WN-S2 (no marking) G4WA-S2 (“ALERT” marking)
Speaker-only models, 70 V: G4WN-S7 (no marking) G4WA-S7 (“ALERT” marking)
The ingenious Genesis G4E Mass Notification Expander provides a separate, independently-controlled strobe that fits behind a Genesis G4 Series speaker or speaker-strobe. (Data Sheet E85001-0610)
Genesis high fidelity Speakers are can generate UL compliant low frequency signals now required for sleeping areas!
Genesis
high fidelity
Speakers are also
UL compliant low
frequency signals
for sleeping
areas!
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
39
No
tific
atio
n A
pp
liances
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
The Genesis line of multi-candela and multi-wattage ceiling signals feature all the hallmarks that have made Genesis products a big hit with designers, engineers, building own-ers, and installers everywhere. Precision timing electron-ics, and low current draw bring the benefits of the popular Genesis wall-mount models to ceiling applications. These signals are 30 percent slimmer than comparable signals on the market. They are compatible with standard 4-inch (10 cm) square electrical boxes and don’t require extension rings or trim plates.
Select ¼, ½, 1, or 2
watt operation!
Select 15/30/75/95
and 95/115/150/177 candela output!
Genesis GC Series Ceiling Models
Speakers and Speaker-Strobes
Fire Alarm Speakers and Speaker-strobes
White housing White housing Red housing All fire alarm appliances come no marking with “FIRE” with “FIRE” with the “Running Man” Icon
GC-S2VM GCF-S2VM 25 V Speaker-strobe (15/30/75/110 cd setting)
GC-S2VMH GCF-S2VMH 25 V Speaker-strobe (95/115/150/177 cd setting)
GCF-S7VM 70 V Speaker-strobe (15/30/75/110 cd setting)
GC-S7VMH GCF-S7VMH 70 V Speaker-strobe (95/115/150/177 cd setting)
GC-S2 GCFR-S2 Speaker-only models, 25 V
GC-S7 GCF-S7 GCFR-S7 Speaker-only models, 70 V
High Fidelity Fire Alarm Speakers and Speaker-Strobes
White housing White housing Red housing Red housing All fire alarm appliances come no marking with “FIRE” no marking with “FIRE” with the “Running Man” Icon
GCHFWN-S2VMC GCHFWF-S2VMC GCHFRN-S2VMC GCHFRF-S2VMC 25 V Spkr + 15/30/75/110 cd strobe
GCHFWN-S2VMCH GCHFWF-S2VMCH GCHFRN-S2VMCH GCHFRF-S2VMCH 25 V Spkr + 95/115/150/177 cd strobe
GCHFWN-S7VMC GCHFWF-S7VMC GCHFRN-S7VMC GCHFRF-S7VMC 70 V Spkr + 15/30/75/110 cd strobe
GCHFWN-S7VMCH GCHFWF-S7VMCH GCHFRN-S7VMCH GCHFRF-S7VMCH 70 V Spkr + 95/115/150/177 cd strobe
GCHFWN-S2 GCHFWF-S2 GCHFRN-S2 GCHFRF-S2 Speaker-only models, 25 V
GCHFWN-S7 GCHFWF-S7 GCHFRN-S7 GCHFRF-S7 Speaker-only models, 70 V
High Fidelity Mass Notification Speakers and Speaker-strobes
Clear lens Amber lens Amber lens White housings with “ALERT” no marking with “ALERT” No “Running Man” Icon
GCHFWA-S2VMC GCHFWN-S2VMA GCHFWA-S2VMA 25 V Speaker, four standard cd settings
GCHFWA-S2VMCH GCHFWN-S2VMAH GCHFWA-S2VMAH 25 V Speaker, four high cd settings
GCHFWA-S7VMC GCHFWN-S7VMA GCHFWA-S7VMA 70 V Speaker, four standard cd settings
GCHFWA-S7VMCH GCHFWN-S7VMAH GCHFWA-S7VMAH 70 V Speaker, four high cd settings
GCHFWA-S2 (25 V, “ALERT” marking) GCHFWA-S7 (70 V, “ALERT” marking) Speaker-only models
Mass Notification Speakers and Speaker Strobes
Clear lens Clear lens Amber lens Amber lens White housings no marking with “ALERT” no marking with “ALERT” No “Running Man” Icon
GCWN-S2VMC GCWA-S2VMC GCWN-S2VMA GCWA-S2VMA Speaker-strobe, 25 V, four standard cd settings
GCWN-S2VMHC GCWA-S2VMHC GCWN-S2VMHA GCWA-S2VMHA Speaker-strobe, 25 V, four high output cd settings
GCWN-S7VMC GCWA-S7VMC GCWN-S7VMA GCWA-S7VMA Speaker-strobe, 70 V, four standard cd settings
GCWN-S7VMHC GCWA-S7VMHC GCWN-S7VMHA GCWA-S7VMHA Speaker-strobe, 70 V, four high output cd settings
GCWN-S2 (25 V) GCWA-S2 (25 V, “ALERT”) GCWN-S7 (70 V) GCWA-S7 (70 V, “ALERT”) Speaker-only models
Data Sheet E85001-0641
Genesis
high fidelity
Speakers are also
UL compliant low
frequency signals
for sleeping
areas!
40
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Genesis WG4 Series Wall Models
Weatherproof Speakers and Speaker-StrobesGenesis WG4 Series speakers and speaker-strobes are among the most ver-satile emergency signals of their kind. Rated for indoor or outdoor use, they are suitable for a wide range of wet and harsh environments with a listed operating temperature range of as low as -31°F to as high as 151°F (-35°C to 66°C).
Refer to Data Sheet E85001-0626 -- Genesis Outdoor Speakers and Strobes for details.
Field Configuration
S1: wattage
S2: Candela
JP1: Strobe temporal mode selection
S3: Speaker voltage
SPKR -SPKR +
STROBE -STROBE +
SPKR -SPKR +STROBE -STROBE +Genesis WG4 speakers may be set 70- or 25-Volt
operation, and for ¼, ½, 1, or 2 watt operation. Strobe models feature four selectable light output settings. Wattage and cd selections are changed by removing the cover and simply sliding the switches to the desired settings, which remain vis-ible through a small window on the front of the de-vice after the cover is replaced. Genesis speaker-strobes may also be configured for temporal flash. This battery-saving feature is intended for private mode signaling only. To set the device for temporal flash, snip the jumper at JP1.
WG4RF-S WG4RF-SVMC WG4WF-S WG4WF-SVMC WG4RN-S WG4RN-SVMC WG4WN-S WG4WN-SVMC WG4WN-SVMA WG4WA-SVMA WG4WA-SVMC
White housing White housing Red housing Red housing Fire Alarm Speakers no marking with “FIRE” no marking with “FIRE”
WG4WN-S WG4WF-S WG4RN-S WG4RF-S 25/70 V Speaker
WG4WN-SVMC WG4WF-SVMC WG4RN-SVMC WG4RF-SVMC 25/70 V Speaker-strobe (15/29/70/87 cd)
WG4WF-SVMHC WG4RN-SVMHC WG4RF-SVMHC 25/70 V Speaker-strobe (102/123/147/161 cd)
Genesis mass notification speakers and speaker-strobes bring the same high-performance fire alarm features and unobtrusive design to mass notification applications. Available with amber lenses and optional “ALERT” lettering, they are ideal for applications that require differentiation between fire alarm and mass notification alerts.
White housing White housing Mass Notification Speakers no marking “ALERT” — white housing, no “Running Man” icon
WG4WN-SVMA WG4WA-SVMA 25/70 V Speaker-strobe, amber lens (13/25/5962 cd output)
WG4WN-SVMHA WG4WA-SVMHA 25/70 V Speaker-strobe, amber lens (84/101/125/130 cd output)
WG4WA-SVMC 25/70 V Speaker-strobe, clear lens (15/29/70/87 cd output)
WG4WN-SVMHC WG4WA-SVMHC 25/70 V Speaker-strobe, clear lens (102/123/147/161 cd output)
WG4WA-S 25/70 V Speaker
Trim skirts
WG4WTS (white) WG4RTS (red) Surface Skirt for Genesis WG4 appliance family.
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
41
No
tific
atio
n A
pp
liances
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Genesis GL Series Wall Models
LED StrobesGenesis GL Series horns and LED strobes break the current draw barrier with innovative technology that not only makes them inexpensive to install and oper-ate, but also allows them to maintain the sleek low-profile design that has made Genesis appliances a favorite among facility owners, architects, and designers. Horn-Strobe models feature field-selectable 15, 30, 75, or 110 cd output set-tings. Horn-strobe and horn-only appliances feature field-configurable high/low dB and temporal/steady audible output.
White housing White housing Red housing Red housing All fire alarm appliances come no marking with “FIRE” no marking with “FIRE” with the “Running Man” Icon
GL1WN-HDVMC GL1WF-HDVMC GL1RN-HDVMC GL1RF-HDVMC Horn-Strobe
GL1WN-HD GL1WF-HD GL1RN-HD GL1RF-HD Horn-only
GL1WN-VMC GL1WF-VMC GL1RN-VMC GL1RF-VMC Strobe-only
GL1WN-TP (white) GL1RN-TP (red) Trim Plate for four-inch square boxes
GL1WN-BB1G (white) GL1RN-BB1G (red) One-gang surface box
Mass Notification
High Power Speaker Arrays Hyperspike High Power Speaker Arrays (HPSA) employ exclusive technology that delivers
lightweight and acoustically sophisticated solutions for outdoor mass notification installations. These rugged units are among the industry’s smallest in physical size, yet they reproduce some of the clearest (up to 0.91 STI, source-dependant) and loudest (up to 126 dBA Fast @ 1m) audio signals available. Loudspeaker heads are as small as 13.2” (33.5 cm) in diameter and 24.7” (62.7 cm) in height. A single panel unit weighs as little as 16 lb (7.3 kg).
Hyperspike assemblies are AC powered with DC backup. They come with a lockable NEMA 4 Electronics Control Cabinet (ECC) that holds the amplifier and battery charger, and a lockable NEMA 4 battery enclosure. Loudspeakers come pre-assembled with an eight foot (2.4 meter) ¾-inch liquid-tight flexible conduit whip and wire leads. Batteries and battery enclosures are ordered separately.
Color: Tan Color: Gray HPSA Assemblies
1600 Watt Class MN-HSHT16P5N MN-HSHG16P5N 1600 Watts, 360° Dispersion, 5 Active Panels Data Sheet E85001-0637
MN-HSHT16P3N MN-HSHG16P3N 960 Watts, 230° Dispersion, 3 Active Panels Data Sheet E85001-0637
MN-HSHT16P2N MN-HSHG16P2N 640 Watts, 185° Dispersion, 2 Active Panels Data Sheet E85001-0637
MN-HSHT16P1N MN-HSHG16P1N 320 Watts, 120° Dispersion, 1 Active Panel Data Sheet E85001-0637
3200 Watt Class MN-HSHT32P5N MN-HSHG32P5N 3200 Watts, 360° Dispersion, 5 Active Panels Data Sheet E85001-0637
MN-HSHT32P3N MN-HSHG32P3N 1920 Watts, 230° Dispersion, 3 Active Panels Data Sheet E85001-0637
MN-HSHT32P2N MN-HSHG32P2N 1280 Watts, 185° Dispersion, 2 Active Panels Data Sheet E85001-0637
MN-HSHT32P1N MN-HSHG32P1N 640 Watts, 120° Dispersion, 1 Active Panel Data Sheet E85001-0637
6400 Watt Class MN-HSHT64P5N MN-HSHG64P5N 6400 Watts, 360° Dispersion, 5 Active Panels Data Sheet E85001-0637
MN-HSHT64P3N MN-HSHG64P3N 3840 Watts, 230° Dispersion, 3 Active Panels Data Sheet E85001-0637
MN-HSHT64P2N MN-HSHG64P2N 2560 Watts, 185° Dispersion, 2 Active Panels Data Sheet E85001-0637
MN-HSHT64P1N MN-HSHG64P1N 1280 Watts, 120° Dispersion, 1 Active Panel Data Sheet E85001-0637
42
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Mass Notification
Medium Power Speaker ArraysEDWARDS brand Hyperspike Series Medium Power loudspeakers employ exclusive HyperSpike technology to deliver lightweight and acoustically sophisticated solutions for large indoor and smaller outdoor mass notification installations.
UL Listed 250-Watt Medium Power Speaker Arrays
EDWARDS brand Model 250 Hyperspike Series UL Listed Medium Power loudspeakers em-ploy HyperSpike® technology to deliver lightweight and acoustically sophisticated solutions for large indoor and smaller outdoor mass notification installations. These UL Listed units are omni-directional loudspeakers that produce 360 degrees of acoustic energy. The high fidelity output remains intelligible over up to a quarter mile from the device. It is rated for indoor or outdoor use. The include four wattage taps: 40 W, 90 W, 125 W, and 250 W.
MN-HSMT25P5N 250-Watt Medium Power Speaker Array, tan housing. Data Sheet E85001-0652
MN-HSMG25P5N 250-Watt Medium Power Speaker Array, gray housing. Data Sheet E85001-0652
MN-HSMR25P5N 250-Watt Medium Power Speaker Array, red housing. Data Sheet E85001-0652
Omnidirectional 650-Watt Loudspeakers
The MN-HSMP650 Series has a 360° omnidirectional sound dispersion pattern and can handle 650 Watts of crystal-clear audio power. It is rated for indoor and outdoor use and hangs from eyebolts or is mounted to a two-inch OD mast.
MN-HSMP650G Loudspeaker assembly, 650 Watt, Gray Housing. Data Sheet E85001-0638
MN-HSMP650P5T Loudspeaker assembly, 650 Watt, Tan Housing. Data Sheet E85001-0638
Omnidirectional Indoor-rated 300-Watt Loudspeakers
The MN-HSMP300DF is a grey indoor-rated omnidirectional unit rated for 300 Watts of con-tinuous audio power. These units are eyebolt-mounted.
MN-HSMP300DF1 Omnidirectional Loudspeaker, 300 Watt. Data Sheet E85001-0638
MN-HSMP300DF170 Omnidirectional Loudspeaker, 300 Watt with 70.7 VRMS transformer. Data Sheet E85001-0638
Directional 200-Watt Loudspeakers
The MN-HSMP200D is a directional loudspeaker that handles 200 Watts of continuous audio. Units feature 60° x 30° sound dispersion and are suitable for indoor or outdoor applications. They come complete with mounting bracket.
MN-HSMP200D1 Directional Loudspeaker, 200 Watt. Data Sheet E85001-0638
MN-HSMP200D170 Directional Loudspeaker, 200 Watt with 70.7 VRMS transformer. Data Sheet E85001-0638
Portable Loudspeaker System
The MN-HSPB is a self-contained, portable loudspeaker system that weighs a mere 15 lbs. Despite its light weight, the MN-HSPB packs a peak acoustic output of 144dB for an intel-ligible communication range of more than 2,450 feet (750 m).
MN-HSPB-S HS Series Portable Handheld Speaker - Standard Output Data Sheet E85001-0653
MN-HSPB-H HS Series Portable Handheld Speaker - High Output Data Sheet E85001-0653
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
43
No
tific
atio
n A
pp
liances
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Firefighters’ TelephonesFirefighters’ telephones are typically installed in corridors, lobbies, mechanical rooms, stairways, or other stategic locations. When lifted from its cradle, or plugged into a suitable wall jack, the hand-set activates audible and visible signals at the EST3 control panel.
Edwards fire alarm telephones are rugged communications de-vices for emergency use. Enclosed keylocked telephone stations comprise three separately ordered components: the handset assembly, the frontplate, and the wallbox. Depending on how the phones are wired, they are supervised for three or four state operation. Frontplates are available with either metal or break glass insterts.
MEA approved warden stations feature doors with magnetic latches and one-state handsets with armoured cords. Warden stations mount to 6832-1 wallboxes. Portable handsets plug into one-gang receptacles. Handsets are available in black or red. The TCS-6 cabinet provides storage for up to six handsets.
6831-46831-1 6830-4 6830-3
6833-4
6830-NY-S4
6832-1
Firefighters’ Telephones 6830-NY-F4 Four-state Remote Telephone Warden Station - Flush. Armored armored cord.
6830-NY-S4 Four-state Remote Telephone Warden Station - Surface. Armored armored cord.
6830-5A-4 Four-state Telephone Handset Assembly - Red, 60” (1500mm) Coiled Cord, Push-to-talk button.
6830-6A-4 Four-state Telephone Handset Assembly - Red, 60” (1500mm) Armored Cord, Push-to-talk button.
6830-4 Four-state Telephone Handset Assembly - Red, 60” (1500mm) Coiled Cord.
6830-5A-4 Three-state Telephone Handset Assembly - Red, 60” (1500mm) Coiled Cord, Push-to-talk button.
6830-6A-4 Three-state Telephone Handset Assembly - Red, 60” (1500mm) Armored Cord, Push-to-talk button.
6833-4 Four-state Portable Telephone Handset Receptacle, 1-gang Stainless-steel Faceplate.
6830-3 Portable Telephone Handset - Black c/w 60” (1500mm) Coiled Cord.
6700-0061 Portable Telephone Handset - Red c/w 60” (1500mm) Coiled Cord.
6831-1 Frontplate - Flush Mount, Red Finish, Break Glass Type c/w 2 keys.
6831-2 Frontplate - Flush Mount, Red Finish, Non-Break Glass Type c/w 2 keys.
6831-3 Frontplate - Surface Mount Red Finish, Break Glass Type c/w 2 keys.
6831-4 Frontplate - Surface Mounting Red Finish, Non-Break Glass Type c/w 2 keys.
6832-1 Wallbox - Flush or Surface mount, Red finish. 14” (356mm) H x 8-1/2” (216mm) W x 3½” (89mm) D.
TCS-6 Portable handset storage cabinet. Surface mount c/w keylock. Red finish with white lettering.
TB1
1
2
3
5
6
7
8
4
Compatible signalmodule.
Printed circuit board
24 Vdc
24 Vdc
UL/ULC listedpower supply
Telephone riser
Control relay module to operateTelephone in Use indicator light.
47 kW
Normal(on hook)
TB1
1
2
3
5
6
7
8
4
Compatible signalmodule.
Printed circuit board
24 Vdc
24 Vdc
UL/ULC listedpower supply
Telephoneriser
Control relay module to operateTelephone in Use indicator light.
47 kW
Normal(on hook)
Active(off hook)
Three-state operation
Four-state operation
44
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
HousingSurface Box (optional)
North American2-gang electrical box
Mounting Plate
Single Captive Mounting Screw
H+H-S+S-
Horn/Strobe
H+H-S+S- To Next Device
or EOL Resistor
To Fire AlarmControl PanelSignal Circuit
+
+
First Device
-
-
Horn/Strobe
Re-Entrant Speakers and Speaker-StrobesRe-entrant speakers feature a sealed, high efficiency compression driver that’s both weatherproof and vermin proof. This makes them ideal for public places and outdoor areas such as parking garages and transport terminals. All Integrity speakers include a DC Blocking Capacitor that permits electrical supervision of the audio distribution circuit. Models for 25Vrms and 70Vrms circuits are available.
Fire Alarm Appliances, clear lenses, Data Sheet E85001-0317
15/75 cd 30 cd 110 cd Speaker only
757-7A-RS25 757-3A-RS25 757-8A-RS25 757-1A-R25 Speaker-strobe, 25 V, red housing
757-7A-RS25W 757-3A-RS25W 757-8A-RS25W 757-1A-R25W Speaker-strobe, 25 V, white housing
757-7A-RS70 757-3A-RS70 757-8A-RS70 757-1A-R70 Speaker-strobe, 70 V, red housing
757-7A-RS70W 757-3A-RS70W 757-8A-RS70W 757-1A-R70W Speaker-strobe, 70 V, white housing
Mass Notification Appliances, amber lenses, Data Sheet E85001-0317 757-7A-RS25WA (12/75 cd) 757-8A-RS25WA (88 cd) Speaker-strobe, 25 V, white housing
757-7A-RS70WA (12/75 cd) 757-8A-RS70WA (88 cd) Speaker-strobe, 70 V, white housing
Temporal Horns and Horn-Strobes During installation, the Horn is configured for steady or temporal tone signal. When temporal output is selected, all Horns on a common two-wire circuit are self-synchronized. Integrity Series Horns emit a low frequency “growling” tone that demands attention. Horns can be configured for either high output (98 dBA) or low output (94 dBA); and are listed for outdoor use.
757-1A-T (Red) 757-1A-TW (White) Temporal Horn Data Sheet E85001-0341
757-7A-T (Red) 757-7A-TW (White) Temporal Horn-Strobe, 15/75cd Data Sheet E85001-0341
757-4A-T (Red) 757-4A-TW (White) Temporal Horn-Strobe, 75cd Data Sheet E85001-0341
757-8A-T (Red) 757-8A-TW (White) Temporal Horn-Strobe, 110cd Data Sheet E85001-0341
4” Square Box Mount Strobes405 Series strobes are self-synchronized to flash at one fps across their full operating voltage range. UL 1971 synchronization requirements are achieved when used with the G1M Signal Master. Strobes must be connected to signal circuits that output a constant (not pulsed) voltage. A diode is used to allow full signal circuit supervision. 405 Series strobes are suitable for outdoor use and installed to a standard four-inch square electrical box.
405-5A-T (Red) 405-5A-TW (White) Strobe - 15 cd Data Sheet E85001-0305
405-7A-T (Red) 405-7A-TW (White) Strobe - 15/75 Data Sheet E85001-0305
405-3A-T (Red) 405-3A-TW (White) Strobe - 30 cd Data Sheet E85001-0305
405-6A-T (Red) 405-6A-TW (White) Strobe - 60 cd Data Sheet E85001-0305
405-8A-T (Red) 405-8A-TW (White) Strobe - 110 cd Data Sheet E85001-0305
CS-405-7A-T (15/75 cd) CS-405-8A-T (110 cd) Strobe - Weatherproof (red) Data Sheet E85001-0305
Enhanced Integrity Series
Harsh Environment Signals
All Enhanced Integrity devices are UL 1971 listed for both wall and ceiling orien-tation. Enhanced Integrity strobes meet the latest UL1971 synchronization re-quirements when used with the G1M Signal Master. Integrity devices are shipped with wall mount style “FIRE” lens markings. Other lens markings are available.
Hazard
ous Lo
cation
Devices
Do
or H
olders &
Relays
45
No
tific
atio
n A
pp
liances
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
Fire Alarm Bells
Edwards fire alarm bells are of the underdome type with heavy-duty mechanisms. Gongs are made of selected alloy steel to generate the loud, resonant tones. For weatherproof ap-plication, optional surface weatherproof backboxes are available.
323D-10AW (Grey) 323D-10AW-R (Red) 10-inch Single Stroke, Diode — 20-24Vdc Data Sheet E85001-0333
439D-6AW (Grey) 439D-6AW-R (Red) 6-inch Vibrating, Diode — 20-24Vdc Data Sheet E85001-0333
439D-10AW (Grey) 439D-10AW-R (Red) 10-inch Vibrating, Diode — 20-24Vdc Data Sheet E85001-0333
Multiple Tone Signal
The 5530MD-24AW is a weatherproof heavy-duty industrial, tone-selectable, signaling de-vice capable of producing volume-controlled, high-decibel tones. It uses a microprocessor circuit to create 27 distinctive tones. A single tone may be selected by setting a miniature dip switch within the unit.
5530MD-24AW 27-Tone Selectable Signal — 24Vdc Data Sheet E85001-0415
Multi-purpose LoudspeakerThe HPSA15 loudspeaker is a high-efficiency double re-entrant loudspeaker that operates within a nominal frequency response range of 400-14,000 Hz, and provides audible output of 120 dB (peak at one meter) at the rated power level. It includes a versatile, three-way, 25/70.7 V line transformer that meets a variety of distributed system needs. The transformer is adjustable by means of a convenient seven-position, watts/impedance selection switch.
HPSA15R2570 15-watt loudspeaker, red Data Sheet E85001-0591
HPSA15G2570 15-watt loudspeaker, gray Data Sheet E85001-0591
Audible Signals
Signal Master
The Signal Master is a simple-to-use accessory that adds enhanced features to Genesis and Integrity strobes and Horn-Strobes. It is a dual-purpose module that provides UL 1971 required precision synchronization for con-nected Integrity and Genesis strobes, and independent control for connected Genesis Horns over a single pair of wires. Two methods of Horn control are available: traditional Horn silence; or, normally-closed contact. Both methods may be used to silence Horns without turning off strobes on the same circuit. Two models are available. The Genesis “piggyback” model doesn’t require a separate electrical box. It simply snaps to the back of the first G1 signal on the circuit. The remote mount model mounts in a North American 2½ inch (64 mm) deep one-gang box.
G1M Genesis Signal Master – Snap-on (piggyback) Data Sheet E85001-0545
G1M-RM Genesis Signal Master – Remote 1-Gang Mount Data Sheet E85001-0545
Snap-on (piggyback) model
Remote 1-gang mount model
Accessories
46
ES
T3
Net
wor
kIn
itiat
ing
Dev
ices
No
tifi
ca
tio
n A
pp
lianc
es
SUBMIT
EST3N o t i fi c a t i o n A p p l i a n c e s
46
Integrity Lens Marking Kits
Integrity strobes are shipped with wall mount style “FIRE” lens markings. Where ceiling mount, other languages or dif-ferent lens markings are required, optional LKW and LKC series Lens Marking Kits are available. Lens marking sleeves snap right over the strobe lens providing a quick, easy, change.
LKW-1R (Wall orientation) “FIRE” (Red)
LKW-1 (Wall orientation) LKC-1 (Ceiling orientation) “FIRE”
LKW-2 (Wall orientation) LKC-2 (Ceiling orientation) “FEU”
LKW-3 (Wall orientation) LKC-3 (Ceiling orientation) “FIRE/FEU”
LKW-4 (Wall orientation) LKC-4 (Ceiling orientation) “SMOKE”
LKW-5 (Wall orientation) LKC-5 (Ceiling orientation) “HALON”
LKW-6 (Wall orientation) LKC-6 (Ceiling orientation) “CO2”
LKW-7 (Wall orientation) LKC-7 (Ceiling orientation) “EMERGENCY”
LKW-8 (Wall orientation) LKC-8 (Ceiling orientation) “ALARM”
LKW-9 (Wall orientation) LKC-9 (Ceiling orientation) “FUEGO”
LKW-10 (Wall orientation) LKC-10 (Ceiling orientation) “ALERT”
Integrity Temporal Horn, Horn/strobe 757A-SB Surface Box, Red, Indoor 757A-SBW Surface Box, White, Indoor 757A-WB Weatherproof Box, Red, Surface 757A-WBW Weatherproof Box, White, Surface
Integrity Speakers, Speaker/strobes 960A-4SF Flush Box, Indoor 757A-SB Surface Box, Red, Indoor 757A-SBW Surface Box, White, Indoor
Integrity Re-entrant speakers, Speaker/strobes 960A-4SF Flush Box, Indoor 757A-SB Surface Box, Red, Indoor 757A-SBW Surface Box, White, Indoor 757A-WB Weatherproof Box, Red, Surface 757A-WBW Weatherproof Box, White, Surface
Integrity Chimes, Chime/strobes 757A-SB Surface Box, Red, Indoor 757A-SBW Surface Box, White, Indoor
Mounting Accessories
Genesis Signals 27193-11 Horn-strobe Surface Box, Red, Indoor 27193-16 Horn-strobe Surface Box, White, Indoor G4RB Speaker Surface Box, Red, Indoor G4B Speaker Surface Box, White, Indoor G4ERB G4 Dual-strobe Format Surface box, Red G4EWB G4 Dual-strobe Format Surface box, White
Horn/siren Combination 349 Weatherproof Backbox
Fire Alarm Bells and CS-405 Series 449 Weatherproof Backbox
Bell/Strobe Plate
The bell/strobe plate is ideal for renovation and retrofit projects, and new construction. It is equipped with an Edwards self-synchronizing strobe and is designed to allow on-site mounting of the 439 series Vibrating Bell, providing instant conversion to Bell/Strobe audible/visual signal appliances. The strobe is designed for 20 to 24Vdc operation and must be connected to signal circuits which output a constant (not pulsed) voltage. A diode is used to allow full signal circuit supervision.
403-5A-R (15 cd) 403-7A-R (15/75 cd) 403-3A-R (30 cd) 403-8A-R (110 cd) Data Sheet E85001-0441
Accessories
Genesis G4B Speaker Surface Box
Hazardous Location Devices
Initiating Devices p. 48
Notification Appliances p. 49
Classes
Class I - Hazardous Gases. Class I locations are areas in which flam-mable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures.
Typical Class I Hazardous Areas• Spray painting and finishing areas• Utility gas plants• Petroleum refining production plants• Petroleum dispensing locations• Dry cleaning facilities• Dip tanks containing combustibles or flammable liquids• Plant facilities extracting solvents• Inhalation anesthetics areas• Process facilities manufacturing pyroxylin type plastics
Class II - Hazardous Dusts. Class II locations represent areas that are hazardous due to the presence of combustible dust.
Typical Class II Hazardous Areas• Flour mills• Feed mills• Grain elevators and grain handling facilities• Aluminum manufacturing and storage areas• Magnesium manufacturing and storage areas• Coal preparation and handling facilities• Starch manufacturing and storage areas• Confectionery plants• Pulverizer sugar and cocoa manufacturing, and storage plants• Spice grinding and storage plants
Class III - Hazardous Fibers. Class III locations have easily ignitable fibers or flyings present, but not likely to be suspended in air in quantities sufficient to produce ignitable mixtures in the atmosphere.
Typical Class III Hazardous Areas• Textile mills• Woodworking plants*• Furniture manufacturers*• Cotton gins• Cotton seed milling plants• Flax plants• Carpet manufacturers
* Except if wood flour (dust), which is Class II Group G, is present
DivisionsThe Location Classes are broken down by the NFPA into Divisions 1 and 2, defining different levels of risk. In general, the risk of there being a hazardous presence of flammable/combustible/ignitable materials is higher for Division 1 than for Division 2. The specifics differ between the three classes (I, II and III). Equipment suitable for Division 1 is also suitable for Division 2 locations.
GroupsClass I and II locations are divided by the NFPA into Group designations identifying specific gases, vapors and dusts by characteristic similarities that relate to specific equipment construction requirements. Class III locations are not divided into separate group designations.
Class I Groups Group A. Atmospheres containing acetylene.
Group B. Atmospheres containing hydrogen, fuel and combustible process gases containing more than 30 percent hydrogen by volume, or gases or vapors of equivalent hazard such as butadiene, ethylene oxide, propylene oxide, and acrolein.
Group C. Atmospheres such as ethyl ether, ethylene, or other gases or vapors of equivalent hazard.
Group D. Atmospheres containing acetone, ammonia, benzene, butane, cyclopropane, ethanol, gasoline, hexane, methanol, methane, natural gas, naphtha (petroleum), pro-pane, or gases or vapors of equivalent hazard.
Class II GroupsGroup E. Atmospheres containing combustible metal dusts, including aluminum, magnesium, and their commercial alloys, or other combustible dusts whose particle size, abra-siveness and conductivity present similar hazards in the use of electrical equipment.
Group F. Atmospheres containing combustible carbona-ceous dusts, including carbon black, charcoal, coal, or dusts that have been sensitized by other materials so that they present an explosion hazard.
Group G. Atmospheres containing combustible dusts not included in Group E or F, including flour, grain, wood, plastic, and chemicals.
Edwards hazardous location devices provide reliable life safety protection and emergency signaling in areas where atmospheres could become harsh or explosive. All hazardous location devices are UL rated under the full range of classifications set out in the National Electrical Code.
The following classification definitions are an interpretive summary based on the latest edition of the National Electri-cal Code (NEC, NFPA 70). Refer to the latest editions of NFPA 497M, NFPA 70 and the UL Hazardous Location Equipment Directory for current and more detailed information. For more information on NEMA classifications, refer to NEMA Standards Publication No. 250.
Hazardous Location Classifications
Ha
zard
ou
s Lo
ca
tion
Devices
Do
or H
olders &
Relays
47
EST3 H a z a r d o u s L o c a t i o n D e v i c e s
ES
T3
N
etw
ork
Initi
atin
g D
evic
esN
otifi
catio
n A
pplia
nces
Ha
zard
ou
s L
oc
ati
on
Dev
ices
SUBMIT
48
EST3 H a z a r d o u s L o c a t i o n D e v i c e s
Initiating Devices
Rate Compensation Heat Detectors
Series 302 heat detectors are designed for use in normal environments as well as environments where the detectors are subject to weather, moisture (internal condensation), and explosive atmospheres. They are normally-open devices designed to close an electrical circuit upon activation. All models feature rate compensation and are available with either 135 °F (57.2 °C) or 194 °F (90 °C) ratings. They are self restoring, hermetically sealed, shock and corrosion resistant, and are tamperproof.
Sensor’s Rated Temperature
Minimum Ambient Air Temperature
Maximum Ceiling Temperature
135 °F (57.2 °C) -40 °F (-40 °C) 100 °F (38 °C)194 °F (90 °C) -40 °F (-40 °C) 150 °F (66 °C)
The sensor's aluminum tube acts as a heat collector when sources of heat radiate directly on the tube. Install these sensors out of direct sunlight and away from radiating heat sources including the direct flow from heaters and heat ducts.
302-AW-135 All-weather Heat Detector - Vertical Mounting FM & UL, 135 °F (57.2 °C) Data Sheet E85001-0589
302-AW-194 All-weather Heat Detector - Vertical Mounting FM & UL, 194°F (90 °C) Data Sheet E85001-0589
302-ET-135 All-weather Heat Detector - Vertical, Box Mount (½" NPT), FM & UL, 135 °F (57.2 °C) Data Sheet E85001-0589
302-ET-194 All-weather Heat Detector - Vertical, Box Mount (½" NPT), FM & UL, 194°F (90 °C) Data Sheet E85001-0589
302-EPM-135 Heat Detector - Explosionproof Mounting UL (Not FM approved), 135 °F (57.2 °C) Data Sheet E85001-0589
302-EPM-194 Heat Detector - Explosionproof Mounting UL (not FM approved), 194°F (90 °C) Data Sheet E85001-0589
AP-P Adaptor plate for mounting 302 and 302-AW to any 3" box or 4" octagon outlet box Data Sheet E85001-0589
JALX11 Explosion proof outlet body with cover - Killark Data Sheet E85001-0589
Explosionproof/weatherproof Manual Stations
MPSR Series explosionproof/weatherproof manual pull stations are noncoded fire alarm stations solidly constructed of die-cast material. They are rated for Class I Group B (hy-drogen) C & D, Class II Groups E. F, G, Class III environments, and are rated NEMA 4X for outdoor use. Key and screw reset models feature terminal connections and come complete with backbox.
Hex Screw Reset Cat 45 Key Reset Manual Stations Data Sheet E85001-0588
MPSR1-DHTWX-GE MPSR1-D45WX-GE Explosionproof Single-action, SPST with backbox.
MPSR1-SHTW-GE MPSR1-S45W-GE Weatherproof Single-action, SPST with backbox.
MPSR1-DHTW-GE MPSR1-D45W-GE Weatherproof Single-action, DPDT with backbox.
MPSR2-SHTW-GE MPSR2-S45W-GE Weatherproof Double-action, SPST with backbox.
MPSR2-DHTW-GE MPSR2-D45W-GE Weatherproof Double-action, DPDT with backbox.
MPSR2-SHTW-GE-NYW MPSR2-S45W-GE-NYW Weatherproof Double-action, SPST with backbox, NYC white stripe.
For French markings add -F to the suffix of the model number. For bilinguial French/English markings add -B to the suffix of the model number.
MPSR-LP Double action cover for explosionproof manual stations
MPSRGR10 Replacement glass rods for MPSR stations (10 pack).
276-K1 Cat 45 Key (each)
Surface Mount
Box mount
Ha
zard
ou
s Lo
ca
tion
Devices
Do
or H
olders &
Relays
49
SUBMIT
EST3 H a z a r d o u s L o c a t i o n D e v i c e s
Hazardous Location Strobes
• Class I, II, or III locations
116DEGEX-FJ hazardous location strobes are life safety signaling appliances designed for installation in hazardous environments. State-of-the-art technology provide for high visual output and low maintenance. The 116DEGEX-FJ has negligible in-rush current. When pendant, wall or ceiling mounted, the 116DEGEX-FJ meets or exceeds the requirements of UL 1971 Signaling Appliance for the Hearing Impaired.
116DEGEX-FJ Explosionproof Strobe, Diode Polarized Data Sheet E85001-0624
116EX-B Wall bracket mounting elbow (required for wall mount applications) Data Sheet K85001-0624
116EX-C Ceiling/wall mounting module (required for wall mount applications) Data Sheet K85001-0624
116EX-P Pendant mounting module - 3/4” (19 mm) NPT Data Sheet E85001-0624
116-GRD Lens Guard Data Sheet E85001-0624
Hazardous Location Bells
• Class I groups B, C and D locations • Class III hazardous locations, for Divisions 1 and 2 • Class II groups E, F and G locations
430D series of hazardous location bells are diode-polarized, heavy duty fire bells for use in life safety applications where a diode supervised signal is required. They can be mounted to any solid surface using two 3/8 inch (10 mm) bolts and the supplied mounting brackets or to a rigid conduit. The integral explosion-proof housing is mechanically terminated to accept a standard 3/4 inch -14 National Pipe Taper (NPT) nipple.
439DEX-6AW (6”) 439DEX-8AW (8”) 439DEX-10AW (10”) Bell – 24 Vdc, Red Data Sheet K85001-0399
439DEX-6AW-R (6”) 439DEX-8AW-R (8”) 439DEX-10AW-R (10”) Bell – 24 Vdc, Grey Data Sheet K85001-0399
Hazardous Location Horns
• Class I groups B, C and D locations • Class III hazardous locations, for Divisions 1 and 2 • Class II groups E, F and G locations
888D and 889D hazardous location horns are diode-polarized, heavy duty, high decibel vibrating horns intended for use in life safety systems in hazardous (classified) locations. These horns may be mounted to any solid surface using two bolts. Each unit is supplied with a sealing fitting for a 3/4 inch -14 National Pipe Taper (NPT) nipple, and wire leads for the electrical connection to the life safety system notification appliance circuit.
888D-N5 (120 Vac) 889D-AW (24 Vdc) Horn – 120 Vac Catalog Sheet: 85001-0397
Notification Appliances
Explosionproof Smoke Detector
Model 30-3013 detectors are high performance smoke detectors built for use in hazardous locations. They are corrosion-resistant and feature a non-conducting aluminum alloy retaining ring that protects the detector sensor against the effects of explosions and other catastrophic events. The retaining ring mounts securely to a companion junction box, which offers several common port configurations for conduit connection. Together, the ring and box provide a sturdy protective shell for the detector head.
30-3013A1N12F Explosionproof Smoke Detector Data Sheet E85001-0645
Do
or
Ho
lder
s
& R
elay
s
50
ES
T3
N
etw
ork
Initi
atin
g D
evic
esN
otifi
catio
n A
pplia
nces
Haz
ard
ous
Lo
catio
n D
evic
es
SUBMIT
EST3 D o o r H o l d e r s & R e l a y s
Door Holders Electromagnetic Door Holders
Electromagnetic door holders keep doors open until signaled by the fire alarm system, a heat detector, a smoke detector, or an electrical switch. Door holders should be installed wherever doors may be effectively used to confine smoke and fire, or where the release of a self-closing door from a remote location is required. Fail-safe operation is an inherent feature of these door holders. If power fails, doors are released automatically, but may be opened or closed manually at any time. All units are free of moving parts, are self-contained, and require no maintenance. Door holders have a holding force of approximately 15-25 Lbf (66-111N).
1501-AQN5 (Single Door) 1502-AQN5 (Double Door) Floor Mounted Data Sheet E85001-0421
1504-AQN5 (Long Catch Plate) 1505-AQN5 (Short Catch Plate) Flush Wall Mounted Data Sheet E85001-0421
1508-AQN5 (Surface) 1505-AQN9 (Completely flush) Wall Mounted Data Sheet E85001-0421
1500-1 (1.5” Extension) 1500-2 (2.5” Extension) Catch Plate Data Sheet E85001-0421
1500-7 (5.25 to 7.5” Extension) 1500-12 (7.5 to 12” Extension) Catch Plate Data Sheet E85001-0421
CS2595-5 (short) CS2598-5 (long) Replacement Armature Data Sheet E85001-0421
Relays Four-Voltage SPDT/DPDT Control Relays
MR Series multi-voltage control relays are ideal for applications where local contacts are required for system status, remote contacts, or for control of electrical loads and general pur-pose switching. They are suitable for use with HVAC temperature control, fire alarm, security, energy management, and lighting control systems. Relays provide 10-Amp contacts, which may be operated by one of four input control voltages. Each relay position contains a red LED that indicates the relay coil is energized. Relays may be snapped apart from a standard four-module assembly and used independently.
MR-101/T (with mounting hardware) MR-101/C (in metal enclosure) Single SPDT relay Data Sheet E85300-02762
MR-104/T (with mounting hardware) MR-104/C (in metal enclosure) 4-position SPDT relay Data Sheet E85300-02762
MR-201/T (with mounting hardware) MR-201/C (in metal enclosure) Single DPDT relay Data Sheet E85300-02762
MR-204/T (with mounting hardware) MR-204/C (in metal enclosure) 4-position DPDT relay Data Sheet E85300-02762
Heavy Duty DPDT Power Relays
MR-199 heavy duty power relays are designed for control applications where 30-Amp DPDT contacts are required. Two models are available: a 115Vac coil and a 24Vdc coil, each of which may be mounted in a rugged steel enclosure.
MR-199X-13 (relay only) MR-199X-13/C (in metal enclosure) Power Relay — 24 VDC Data Sheet E85300-02765
MR-199AX-14 (relay only) MR-199AX-14/C (in metal enclosure) Power Relay — 120 VDC Data Sheet E85300-02765
24 Vac 60 Hz
24 Vdc
120 Vac 60 Hz
Do
or H
old
ers &
Relays
51
SUBMIT
EST3 D o o r H o l d e r s & R e l a y s
SPDT RelaysSingle-pull/double-throw relays are ideal for applications where local or remote con-tacts are required for control of electrical loads. They are suitable for use with HVAC, temperature control, fire alarm, security, energy management, and lighting control systems. Each relay position contains a high-intensity LED which, when illuminated, indicates the relay coil is energized. Individual relay circuits may be snapped apart from standard four- or eight-position modules, and are also available in a single-circuit configuration. The common power to each relay position is bussed on the printed wiring board, which permits power to be connected only once per multi-position module.
Single-Voltage Manual Override Relays
MR-600 series relays provide SPDT, 10-Amp contacts with manual override capability by means of an ON-AUTO-OFF switch. The relay requires a 24Vac or 24Vdc power source supplied by the controlling system. With the switch in the ON position the power relay is energized. With the switch in the AUTO position the relay is allowed to operate as signaled by the controlling system. With the switch in the OFF position the relay cannot be energized.
MR-601/T (with mounting track) MR-601/S (with mounting spacers) Single SPDT relay Data Sheet E85300-02761
MR-604/T (with mounting track) MR-604/S (with mounting spacers) 4-position SPDT relay Data Sheet E85300-02761
MR-608/T (with mounting track) MR-608/S (with mounting spacers) 8-position SPDT relay Data Sheet E85300-02761
Three-Voltage Control Relays
MR-800 Series relays provide SPDT 10-Amp contacts that may be operated by one of three input control voltages: 24Vdc, 24Vac or 115Vac.
MR-801/T (with mounting track) MR-801/S (with mounting spacers) Single SPDT relay Data Sheet E85300-02763
MR-804/T (with mounting track) MR-804/S (with mounting spacers) 4-position SPDT relay Data Sheet E85300-02763
MR-808/T (with mounting track) MR-808/S (with mounting spacers) 8-position SPDT relay Data Sheet E85300-02763
Four-Voltage Control Relays
MR-700 Series relays provide SPDT 10-Amp contacts that may be operated by one of four input control voltages: 12Vdc, 12Vac, 24Vdc, or 24Vac.
MR-701/T (with mounting track) MR-701/S (with mounting spacers) Single SPDT relay Data Sheet E85300-02764
MR-704/T (with mounting track) MR-704/S (with mounting spacers) 4-position SPDT relay Data Sheet E85300-02764
MR-708/T (with mounting track) MR-708/S (with mounting spacers) 8-position SPDT relay Data Sheet E85300-02764
Three-Voltage Encapsulated Control Relays
PAM-1 relays provide 10-Amp Form C contacts. The relay may be energized by one of three input voltages: 24Vac, 24Vdc, or 115Vac. The PAM-1 may be mounted with double-sided adhesive tape, a self-tapping screw, or loosely placed in a backbox.
PAM-1 Encapsulated SPDT relay Data Sheet E85300-02766
Proven leadership. Proud heritage.Shared vision.
In 1872 when Robert Edwards
installed an electrically-operated
gas lamp igniter in a New York
City church, he began a tradition
of innovation that would chart
the course of building safety and
security for the next 140 years.
Today the company that bears his
name draws on this rich legacy of
inventiveness, and benefits from
fresh new alliances established
with one underlying goal:
uncompromised excellence.
Today EDWARDS meets this
goal with quality products and an
exceptional sensitivity to the needs
of our customers. Now we have
access to the resources, talent, and
experience that is already setting
a coordinated plan for excellence
into action. The result is a unique
synergy sustained by a strong
organization with a well-defined
vision of the future.
That vision of excellence
is why EDWARDS is among the
fastest growing building systems
providers today. It’s also why, with
more than a century of solid growth
behind us, you can put your trust in
EDWARDS.
See what’s possible now.
12-21-17
LIFE SAFETY & INCIDENT MANAGEMENT
Contact us...
Email: [email protected]: edwards-fire.com
1016 Corporate Park Drive Mebane, NC 27302
EDWARDS is a registered mark in the United States and other countries.
© 2018 United Technologies Corporation. All rights reserved.
EDWARDS Strategic Partners:
Innovation, leadership, and a rich tradition of excellence...Whether EDWARDS life safety systems are protecting the lives and livelihoods
of the people who make businesses run, or the lives entrusted to the care of
public institutions; whether they’re charged with protecting the guests of the
world’s finest hotels, or preserving irreplaceable artifacts that bring history to life;
EDWARDS stands alone as the brand closely associated with some of the most
important and far-reaching developments in the life safety industry today.
Our strength is in our Strategic Partners — the people and organizations
we entrust with the technology that has charted the course of life safety protec-
tion for decades. Strategic Partners are not middlemen or go-betweens. They
are independent contractors who add value to the EDWARDS life safety solution.
As insiders, they enjoy exclusive access to products, custom design innovations,
and factory training. Yet as successful independent contractors, they are adept
at ensuring that each submittal is strong and competitive, and that each bid is
locally relevant to your installation. As local businesses they not only have to earn
your trust — they have to keep it.
Together these strengths set EDWARDS installations apart, and have
earned this brand a special place among life safety and security solutions avail-
able today. Perhaps that’s why many of the world’s most cherished landmarks
are protected by EDWARDS products. From the Bibliotheca Alexandrina Muse-
um in Egypt, to the modern-day sphinx at the Luxor Hotel in Las Vegas, profes-
sionals who design, own and occupy the world’s most impressive structures
have chosen the EDWARDS solution.
See what’s possible now...
Contact your EDWARDS Strategic Partner today!
E85010-0099 Rev 1.1
![EST3 v5[1].0 Installation & Service Manual](https://static.fdocuments.in/doc/165x107/55cf93fa550346f57b9ef906/est3-v510-installation-service-manual.jpg)
![The University of Sydney - AVOID GLARE [3.5] Submittal Form...Reduce glare through the use of fixed shading devices, window tinting or operable devices such as shades or blinds. Provide](https://static.fdocuments.in/doc/165x107/603075b76cb98308e06441d7/the-university-of-sydney-avoid-glare-35-submittal-form-reduce-glare-through.jpg)
![270412 R4[1].0 EST3 SelfStudy](https://static.fdocuments.in/doc/165x107/5695d53d1a28ab9b02a4917b/270412-r410-est3-selfstudy.jpg)
