Study of Road Accidents in India
-
Upload
purushottam -
Category
Documents
-
view
17 -
download
4
description
Transcript of Study of Road Accidents in India
STUDY OF ROAD ACCIDENTS IN INDIA
INTRODUCTION
Road accidents are one of the causes of disability, injury and death.
India has the highest road traffic accident rate worldwide with over 140000 deaths annually, beating even China. Every hour nearly 14 lives are lost due to road accidents.
Most accidents occur during peak hours considered an ‘unsafe’ or dangerous time due to complex flow pattern of vehicular traffic.
Thus traffic engineers have to undertake a big responsibility of providing safe traffic movements to the road users and ensure their safety.
Road accidents cannot be totally prevented but by suitable traffic engineering and management the accident rate can be reduced to a certain extend.
Studies on road accidents in India
COMMON CAUSES OF ROAD ACCIDENTS SPEEDING
CARELESS DRIVING
DRINKING DRIVING
SEAT BELT WEARING
INEXPERIENCE
LOSS OF CONTROL
FAILED TO LOOK PROPERLY
AT WORK
UNSAFE VEHICLE DESIGN.
LACK OF PROPER LAWS
PATHETIC CONDITION OF ROADS
• Defects in the quality of materials used.
• Defects in construction methods and quality control during construction.
• Does not follow the correct geometric standards.
• Inadequate surface or subsurface drainage in the locality resulting in the stagnation of water in the sub grade or in any of the pavement layers.
• Lack of proper maintenance.
• Increase in the magnitude of wheel loads and the number of load repetitions due to increase in traffic volume.
• Settlement of foundation of embankment of the fill material itself.
• Environmental factors including heavy rainfall, soil erosion, high water table, snow fall ,frost action ,etc..
STEPS TO BE TAKEN FOR PREVENTING ROAD ACCIDENTS…. Strict enforcement of speed limits.
One way traffic should be implemented.
Roads should be widened wherever required.
Curvatures should be minimized.
Footpaths and medians should be made mandatory for all important roads.
Zebra crossing should be provided.
Provide signals, road markings, sign posts..
Construction of humps in important places, accident prone areas ,etc.. And it must be mark properly to avoid accidents
Traffic rules should be strictly enforced.
PAVEMENT SAFETY FACTORS
SURFACE TEXTURE
PAVEMENT ROUGHNESS AND SURFACE DISTRESS
PAVEMENT SHOULDER DESIGN
RUMBLE STRIPS
PASSING LANES
TIME OF DAY AND WEATHER CONDITON
INCORPORATING ROAD SAFETY IMPROVEMENTS
Road surfaces must ensure an adequate level of friction at the tyre pavement interfaces to provide safe operation of vehicles.
Pavement surface properties
• Micro texture – tyre pavement contact, skid resistance
• Macro texture –drainage ability
SURFACE TEXTURE
PAVEMENT ROUGHNESS AND SURFACE DISTRESS “potholes, bumps or ruts”.
Driving on roads in good condition, higher accident may occur due to high speed, lower skid resistance and some other safety factors.
Single and multiple vehicle accident rates.
To decrease single vehicle road accidents by reducing the roughness of the roads, which increase the quality of driving.
Multiple road accidents on rougher roads contain two factors
Lateral variation in vehicle path
Road defects
PAVEMENT SHOULDER DESIGN
Shoulder performs variety of functions
o Lateral support
o Provides area
o Provide easy driving
o Safety zone for parking
o Improve sight distance
Shoulder reduces accident rates for various lane width categories such as
1-1.2m - 3m lanes
1.5m - 3.30m & 3.60m
Median shoulder width increases, accidents increases…
Main functions of traffic engineering studies is to improve safety by
• Minimizing shoulder drop-off
• Increase driver comfort
• Reduce property damage
RUMBLE STRIPS
Effective low cost method of providing guidance for drivers.
Mainly helpful at the time of winter storms, which reduces the visibility of pavement marking.
Installed wherever the shoulder width is 2m or more.
On shoulders adjacent to climbing lanes, rumble strips may be installed on 1.5m shoulder also.
PASSING LANES
Road system must have a wide paved lanes.
It helps in reducing problems during overtaking and to avoid queues of vehicles on the road.
It also provide adequate gap in the opposing traffic nor absence of solid barrier lines.
TIME OF DAY AND WEATHER CONDITION These are highly related to road
accident rates.
About 68% of accidents occur during daylight hours while 27% occur during the hours of darkness and the remaining 5% occur during low light conditions.
High accident areas can be targeted with innovative signing or reflectivity to ensure drivers are aware of their environment.
INCORPORATING ROAD SAFETY IMPROVEMENTS Pavement engineering properties
associated with road safety, there are various treatments available…
“skid resistance” can be restored by a list of specific treatments such as.. ‘surface milling, grooving, blasting, chip sealing, micro-surfacing, slurry seal, planning, bush hammering, etc..
Also based on pavement roughness, surface condition evaluation, pavement performance experience, surface visibility and paving materials, etc..
CLASSES OF FACTORS & INDICATORS
MAINTENANCE TREATMENT & ROAD SAFETY IMPROVEMENTS
ENGINEERING APPLICATIONS IN THE FIELD OF TRANSPORTATIONRoad safety is an integral part of
engineering design.
IRC formulates codes for road construction ,maintenance and also for road safety.
National highways used to be built through PWDs, which connects the entire states of nation.
NHAI
Policy is to provide bypass, service lanes….
MAJOR CHALLENGES PRETAINING TO ENGINEERING MEASURES..
Accessibility rather than mobility
Economic growth and development
Deficiency of funds for non-NHDP networks
Available funds for maintenance & repair is only about 35%-40% of the estimated fund
PRESENT POLICIES REGARDING ENGINEERING MEASURES FOR ROAD SAFETY• Short term solutions
Inadequate provision of SSD, signage, shoulder width, delineators, pedestrian railing, crash barriers, edge and lane marking…..
• Medium term solutions
Improvement of junctions, culvert parapet, lack of visibility at night, safety measures for pedestrians, rest areas, shoulder consolidation…..
• Long term solutions
Construction of service road, grade separator intersections, under passes, flyovers, climbing lane at steep gradient….
GEOMETRIC DESIGN CONSIDERATIONS OF ROADS TO PREVENT ACCIDENTSBasic objectives of geometric design are
Optimize efficiency
Safety
Minimizing cost
Minimizing environmental damages
Livability
Geometric design can be broken into 3 parts
Alignment
Profile
Cross section
ALIGNMENT- route of the road, defined as a series of horizontal tangents and curves
PROFILE – vertical aspect of the road, including crest, sag curves and the straight grade lines connecting them.
CROSS SECTION – position, no of vehicles, bicycle lanes and side walks ,along with their cross slope or banking, drainage features, pavement structure and other items outside the category of geometric design.
DESIGN STANDARDS
Design guidelines taken into account by
Speed
Vehicle type
Road grade (slope)
View obstructions
Stopping distance
AASHTO published primary US guidance on “A Policy on Geometric Design of Highway and Streets” and other standards includes Australian Guide to design and British Design Manual for Roads
PROFILE
Consist of road slopes(grades) connected by parabolic vertical curves
Sag curves –tangent slopes at the end of the curve that is higher than the beginning of the curve
Crest vertical curves –tangent slope at the end of the curve lower than the beginning of the curve
Drainage – poor in sag curves and flat roads
SAG CURVES
Concave upwards
Head light sight distance (S)–important design criteria
S is determined by angle of head light & angle of tangent slopes at the end of the curve
Headlights are 2 ft above the ground and the headlight beam diverges 1° above the longitudinal axis of the vehicle.
CREST CURVES
Convex upwards
Stopping sight distance is the important design criteria, it is determined by the speed of traffic
Sight Distance > Curve Length (S>L)
Sight Distance < Curve Length (S<L)
US standards specify that, the height of driver’s eye is up to 1080mm from the pavement and height of object the driver needs to see as 600mm
Cyclist’s eye height is at 4.5 ft from the pavement
GEOMETRY
CROSS SLOPE
Includes horizontal or lateral slopes
Leveled road creates problem of drainage
In tangent sections,1 – 2% C S is provided
“NORMAL CROWN” is provided
“SUPER ELEVATION” for curved sections
Lower cross slope increases, risk of loss of control increases
8% super elevation is provided for sharp curves
Radius of curve is given by
SAFETY EFFECTS OF CROSS SECTION
Cross slopes and lane width affects the safety performance of a road
‘lane departure crashes’ are mostly on narrow lane roads
SIGHT DISTANCE
Length of road way ahead visible to the driver
It is the distance travelled during two phases
Perception reaction time
Maneuver time (Brake reaction time)
• Depending upon the situations,3 types of sight distance are used
Stopping sight distance
Decision sight distance
Intersection sight distance
Stopping sight distance- distance travelled during PRT & MT and affected by road conditions, mass of the vehicle, inclination of the road and some other factors
Decision sight distance- used when drivers must make decisions more complex than stop or don’t stop, roads are designed for DSD ,using 6 to 10sec for PRT & 4 to 5sec for MT
Intersection sight distance – distance needed to safely proceed through an intersection ,it depends upon traffic control at the intersection and the maneuver
CONCLUSION
Safety means first aid to the uninjured
Health of the nation is more important than the wealth of the nation
Road safety is a major public health concern
Strict implementation of road safety measures reduces the“ ROAD ACCIDENTS”
REFERENCES
Journal Articles:
DR. (Mrs.) Nishi Mittal & DR. S.M.Sarin,“ characteristics of road accidents in India”, Indian Highways,October 2001
A. Anne Rosaline, B. Sathya Narayanan & S. Shanmuga Sundara Boopathy,“comparison of accident rate using accident ranking”, Indian Highways, September 2012
Dinesh Mohan, “Road accidents in India”, IATSS Research vol.33 No.1,2009
Websites:
Ministry of Road Transport and Highways Transport Research Wing, Government of India, 2009. “Road accidents in India 2009”, http://morth.nic.in/writereaddata/.../RoadAccidents2009750843813.pdf (Viewed on 26 September 2011).
Milan Batista,”On the Mutual Coefficient of Restitution in Two Car CollinearCollisions”,http://arxiv.org/ftp/physics/papers/0601/0601168.pdf (Viewed on 26 September2011).
Prof.TomV.Mathew2012,<http://www.civil.iitb.ac.in/tvm/1111_nptel/582_Accident/plain/plain.html>
Thank you