strong+simple+eAsY weldsale - Soluquip · Cast Iron Construction Resists Warping. 2 Weldsale...
Transcript of strong+simple+eAsY weldsale - Soluquip · Cast Iron Construction Resists Warping. 2 Weldsale...
phone 215.739.7474 fax 215.426.1260 www.weldsale.com email [email protected]
weldsalestrong+simple+eAsY
helping you build it better, faster, for less!
catalog #WB0319 version 1.1p March 19, 2012
50years
in business for
weldsale company, llc
Cast Iron Construction Resists Warping.
2
Weldsale Platens allow you to clamp simply, easily and securely—in seconds—anywhere on the Platen surface…
Weldsale Platens are great for welding, grinding, heating, bending and straightening, layout and set-up. They can be used for Plasma Cutting, Oxy-Fuel Cutting and are excellent for “heating and beating”.
Weldsale Platens are made of HIGH TENSILE STRENGTH GRAY cast iron.
the many benefits of Weldsale cast iron platens include:
• Weld spatter does not easily stick to the cast iron Platen. The small spatter bits simply brush off… the large globs can easily be knocked off with a cold chisel.
• Weldsale Platens will not warp, sag, bend, twist or break under normal conditions.
• You can securely clamp anywhere on the Platen in seconds (using Weldsale Clamps and Tools!).
• Our product is long lasting, staying flat for many years.
• Any size Platen will easily support an amazing amount of distributed load.
Weldsale platens are simple, everyday workhorses that can easily handle your toughest jobs.We look forward to hearing from you!
► TOP SURFACEThe tolerance of the top surface of every Weldsale Platen is ± 0.005" per linear foot. This provides a very flat working surface. Because they are made of cast iron this flatness will be maintained for a long time.
►RAiSEd, mAChinEd bOSSES On SidES When two or more Weldsale Platens are set up
in multiple beds, they fit flush with each other at the slotted holes. This completely eliminates the
possibility of the sides cracking when bolting together. Slots on the bosses make bolt
together simple, fast and easy.
Top View
► mAChinEd ShOUldERS allow exact, completely flush set up of multiple Platen beds. ► SiZE OF
SQUARE hOlE: 1¾" sq.
► ROUnd COUnTER-SUnk hOlES kEEP ThE EnTiRE wORk SURFACE ClEAR OF bOlT hEAdSHeads of the mounting bolts are recessed below the work surface. Bolting the Platen to the stand eliminates any unwanted moving or shifting while removing the workpieces.
very heavy duty platens… WeldsAle plAtens are one of the longest-lasting tools you will ever buy.
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
Weldsale Platens can be ground to closer tolerance for extra cost. Call for details.Specifications subject to change without notice.
► RAdiUS in All FOUR CORnERS OF EACh SQUARE hOlE This cast-in feature of our Platens was designed to reduce the “notch effect” on the corners of each square hole, reducing the chance of cracking from hole to hole.
Underside View
WHY PLATENS ARE USED:• Layout• Bending• Straightening• Minimum set-up time• Restraint during welding• Minimizing distortion• Fixturing• Heating & Beating• Downdraft systems available• Cast iron stays flat
WHERE PLATENS ARE USED:• Maintenance Shops• Fabrication Shops• Production Line Shops• Machinery Builders• Utilities• Ship and Submarine
Facilities• Military and Government
Installations• Laboratories• Robotic Installations• Universities and Training
Facilities
3
downdraft
systems
toolingcutting tables
pyramids
magnets
cubes, kneestowers & tom
bstonesused
platenspp. 6–10
p. 13pp. 14–15
p. 11pp. 16–17
pp. 18–19 platens
pp. 2–5
► CROSS Ribbing in bOTh diRECTiOnSgreatly reduces sagging and warping. Helps to assure a long-lasting, flat working surface on the top side.
STAndARd 1¾" SQUARE hOlES.mACHined CAst iron
► CAST-in SOCkETS On ThE bOTTOm OF EvERy SQUARE hOlE make bolt down of tooling by one operator fast and easy. The operator simply inserts bolt (head first) into the square hole, turns the bolt ¼ turn, then pulls the bolt up into the cast-in socket for positive grip.
► ExTRA ThiCk SkiRTS around the perimeter add strength and durability.
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
Platens take no break, no lunch hour, and no sick days… And there is no adjusting, no tuning, and no maintenance required.Weldsale Platens have no electrical, hydraulic or pneumatic requirements.
*ExclusivE WEldsalE FEaturEs shoWn in blue bold fACe tYpe.
please take a moment to consider the benefits a cast iron platen will add to your shop.
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
WeldsAle plAtens: standard sizes
4
2½' × 5' plAten And stAnd
WS25B Platen WS25BNS Stand
Combined Wt.: 1150 lbs. Overall Ht. 32"
5' × 5' plAten And stAnd
WS55B PlatenWS55BNS Stand
Combined Wt.: 2425 lbs. Overall Ht. 32"
5' × 8' plAten And stAnd
WS58B Platen WS58BNS Stand
Combined Wt.: 3630 lbs. Overall Ht. 32"
5' × 10' plAten And stAnd
WS510B Platen WS510BNS Stand
Combined Wt.: 4575 lbs. Overall Ht. 32"
4' × 4' plAten And stAnd
WS44B PlatenWS44BNS Stand
Combined Wt.: 1345 lbs. Overall Ht. 32"
WS56B PlatenWS56BNS Stand
5' × 6' plAten And stAnd
Combined Wt.: 2795 lbs. Overall Ht. 32"
ligHt dutY 3' × 6' plAten & stAndWS36D Platen WS36DNS Stand
Combined Wt.: 1050 lbs. Overall Ht. 36"
WeldsAle steel stAndsStand Part Number
Stand Size
StandHt.
Approx. Wt.(lbs.) Stand Price
WS510BNS 5' × 10' 26.5" 495WS58BNS 5' × 8' 26.5" 390WS56BNS 5' × 6' 26.5" 330 CallWS55BNS 5' × 5' 26.5" 315 forWS44BNS 4' × 4' 26.5" 280 PricesWS25BNS 2.5' × 5' 26.5" 275WS36DNS 3' × 6' 34" 210
Custom height stands available. Call for details.
WeldsAle plAtensPlaten
Part Number Size Approx. Wt. (lbs.)
Platen Price
WS510B 5' × 10' × 5.5" 4080WS58B 5' × 8' × 5.5" 3240WS56B 5' × 6' × 5.5" 2465 CallWS55B 5' × 5' × 5.5" 2110 forWS44B 4' × 4' × 5.5" 1065 PricesWS25B 2.5' × 5' × 5.5" 875WS36D 3' × 6' × 2" 840
Weldsale Platens and stands ship freight class 70.
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
5
platenssteel stands
► OUR STAnd dESign AllOwS SimPlE & FAST FiT UP OF mUlTiPlE PlATEnS inTO lARgER bEdS.
► ClAmP, wEld, bEnd, STRAighTEn, gRind, ASSEmblE, hEAT & bEAT… wiTh wEldSAlE PlATEnS.
Ws510bns
5' × 10'
Ws510b
Ws58bns
5' × 8'
Ws58b
Ws56bns
5' × 6'
Ws56b
Ws55bns
5' × 5'
Ws55b
Ws44bns
4' × 4'
Ws44b
Ws25bns
2.5' × 5'
Ws25b
Ws36dns (LIGHT DUTy)
3' × 6'
Ws36d
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
PriCes effeCtive MArCH 19, 2012
* WELdSALE FLExTOOLING IS COvEREd bY US PATENT #4,867,427.
tools on Pages 6 tHRU 12 fit standaRd 1¾" sqUaRe Holes, typical of Weldsale Platens.
All Weldsale flextooling is shipped Class 70 or UPs. specifications and prices on Platens/tooling subject to change without notice.
WS16-134-20*20" Vertical ClampIdentical to WS16-134, except that it has a larger clamping envelope of 20".7.5 lbs. $199.00
WS16 -134* 9" Vertical Clampthe round knurled boot simply drops into a square hole.Clamping envelope: 0"– 9"Throat: 4½"6.5 lbs. $159.00 WS16-134LR*
Long Reach 9" Vertical ClampSimilar to our standard 9" clamp but with a longer reach.Clamping envelope: 9"Clamping throat, or reach: 7¾"7.5 lbs. $169.00
WS16-134-20LR* Long Reach
20" Vertical ClampSimilar to our standard
20" clamp (WS16-134-20) but with a longer reach.Clamping envelope: 20"
Throat: 7¾"8.5 lbs. $209.00
6
WS18-134*Horizontal
clamping in any radial directionClamping height:
2" (with sliding arm reversed) to 15"
Throw of screw: 3½" 7 lbs. $199.00
WS14-134*Light Duty Vertical Clamp
recommended for use only on Weldsale WS36D
Light Duty 3' x 6' Platens Reduced weight and reduced cost.
Rated at 950 lbs. clamping pressure at 6" height.
Clamping Envelope: 0–18" Throat: 4½"
5 lbs. $119.00
WS30-134*90º Mitre Clamp• Clamping action
for mitre joints.• Typically used with
other tools such as Ws31 angle Plate or WsCorner12.
Throw of screw: 3½" 10 lbs. $289.00
siMPle, sUPer-fAst And sUPer-strong:four easy steps to install:
1. Drop clamp into square hole2. Tilt clamp back 3. Slide arm down4. Turn screw
All clamping force is directed straight down.
WeldsAle flextooling* fast-action clamping… our customers’ favorites!
foR 1¾" sqUaRe Holes. (For 1½" and 1⅝"square holes See Page 17.)
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
** Longer rail lengths available by special order. Call for details.
see Page 17 foR tooling foR Used Platens (1½" and 1⅝"square holes).
platenspp. 2–5
downdraft
systems
cutting tablespyram
idsm
agnetscubes, knees
towers & tombstones
used platens
p. 13pp. 14–15
p. 11pp. 16–17
pp. 18–19 tooling
pp. 6–10
WS26-134*6½" Vertical Pipe ClampClamp is designed to securely hold pipe and curved, narrow, or flat surfaces. Clamping envelope:0"– 6½"Throat: 4½"8 lbs. $209.00
WS28-134*13" Horizontal Pipe Clamp**face pads are self-aligning to apply horizontal pressure on almost any surface.Clamping height: 2" (with sliding arm reversed) to 13"Throw of screw: 3½" 9 lbs. $229.00
WS26-134-20LR*Long Reach 18" Vertical Pipe Clamp
Clamping Envelope: 0" to 18"
Throat or Reach: 7¾"11 lbs. $259.00
WS26-134LR*Long Reach 6 ½" Vertical Pipe ClampClamping Envelope: 0" to 6½"Throat, or Reach: 7¾"9 lbs. $219.00
7
WS26-134-20*18" Vertical Pipe Clamp This clamp is identical to our WS26-134 shown at left, except that it has a larger clamping envelope of 18".Throat: 4½"10 lbs. $249.00
fast-action pipe clampswith v-groove swivel pads
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
PriCes effeCtive MArCH 19, 2012
bolt-doWn flextooling
All Weldsale flextooling is shipped Class 70 or UPs. specifications and prices on Platens/tooling subject to change without notice.8
WS5BD Horizontal Clamp w/Bolt Down Boot
• 360° Swivel• Adjustable height boot
Clamping envelope: 3"–10" Throw of screw: 7¼"13 lbs. $91.00
WS17-134-1616" Vertical Bolt Down ClampThis clamp is identical to our WS17-134, except that it offers a larger clamping envelope.Clamping envelope: 0"–16"Throat: 4½"10 lbs. $309.00
WS17-1345" Bolt Down Vertical Clamp
This clamp bolts into square hole on Platen using the cast-in socket
unique to Weldsale Platens.Clamping envelope: 0"–5"
Throat: 4½"8 lbs. $279.00
WS17-134-16LRLong Reach 16" Vertical Bolt Down ClampThis clamp is identical to our WS17-134-16, except that it offers a longer reach.Clamping envelope: 0"–16"Clamping throat, or reach: 7¾"11 lbs. $319.00
WS17-134-28Extra Long
28" Vertical ClampArm slides up & down rail 360° rotation. Excellent for
clamping tall parts.Clamping envelope: 0"–28"
Throat: 4½"12 lbs. $319.00
WS17-134-28LRLong Reach Extra Tall
28" Vertical Clamp360° rotation
Excellent for clamping tall parts.Clamping envelope:
0"–28" Throat: 7¾"
13 lbs. $329.00
WS17-134LRLong Reach 5" Bolt Down Vertical ClampThis clamp is identical to our WS17-134, except that it offers a longer reach.Clamping envelope: 0"–5" Clamping throat, or reach: 7¾"9 lbs. $287.00
Works with cast-in sockets exclusive to WeldsAle PlAtensClamp must be bolted into hole. Some customers prefer this style. The clamp does not tilt back and can be easier to keep in place. When loose, it can be rotated away from work so weldment can be removed. Bolt-down tools are a bit slower to install than fast-action clamps (see p. 7). Bolt-down clamps cannot be used with generic or acorn brand Platens. Bolt-down feature allows 360˚ rotation.
foR 1¾" sqUaRe Holes. (For 1½" and 1⅝"square holes See Page 17.)
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
WS37BD V Block
• Adjustable height v-block to support pipe, angle or tubing. Can be used with WS26 Pipe Clamp.
• Holds steel 3" to 10" above Platen. Head is fixed.
9 lbs. $168.00
WS35Horizontal Bolt Down Toggle Clamp
• base bolts down into cast-in sockets for quick-action clamping
• 360° Swivel in hole• Adjustable height clamping with
12" bolt down baseClamping envelope: 1¼" to 11¾"Throat: 2"– 4"8 lbs. $172.00
WS34Vertical Bolt Down Toggle Clamp
• base bolts down into cast-in sockets for quick-action clamping
• 360° swivel in hole• Adjustable height clamping
with 12" bolt-down base.Clamping Envelope: 0" to 13"Throat: 4¼"10 lbs. $172.00
WS37WR 13⁄16" Wrench Re-designed wrench fits all bolt-down tooling.2 lbs. $16.00
WS37BD-30Adjustable height V-Block To support pipe, angle and tubing. Holds steel from 3" to 30" above Platen. Head is fixed.12 lbs. $198.00
WSARROWBD Bolt Down Arrow ToolCan hold angle iron above Platen surface.8 lbs. $168.00
wS37 wREnCh ShOwn wiTh POTEnTiAl APPliCATiOnS
tHese tools Have boots (oR bases) tHat bolt into PlaCe foR stability.
* WELdSALE FLExTOOLING IS COvEREd bY US PATENT # 4,867,427. 9
bolt-doWn flextooling
see Page 17 foR tooling foR Used Platens (1½" and 1⅝"square holes).
weldsale co. 215.739.7474 www.weldsale.com email: [email protected]
10 PriCes effeCtive MArCH 19, 2012All Weldsale flextooling is shipped Class 70 or ups. specifications and prices on Platens/tooling subject to change without notice.
WSSHELF30 Height adjusts 5" to 30".22 lbs. $295.00
WSSHELF18 Same uses as WSShelf 30.Height adjusts 5" to 18".18 lbs. $265.00
WSSHELF30 WSSHELF18
WSUNIVISE8 An adjustable clamping system. Jaws crank open and closed, without tools. Will hold your work at nearly any angle above the Platen surface. Includes the two WSPOST18 supports as pictured.32 lbs. $499.00
WSCRADLE6Will hold pipe up to 6" diameter. The “bolt down” arrangement allows you to position your pipe in any orientation along the Platen.11 lbs. $199.00
WSBRIDGE620A bridge between two WSSHELF units that provides you with a larger surface that is adjustable in height and angle. Can also be used with one of our accessories (shown below). 6" wide × 20" long × ½" thick.28 lbs. $49.00 (Bridge only)
WSCRADLE6 with WSCHAINVISE
foR 1¾" sqUaRe Holes. (For 1½" and 1⅝"square holes See Page 17.)
WssHelfsystem
ACCessories for workholding above the Platen:These accessories will hold pipe, tube, angle, channel and flat stock above the Platen surface. They can be used with or without the WSSHeLF System.
An adjustable Platform–or shelf– above the Platen.It can support your work piece or can be used with Clamps and accessories (as shown). Will hold pipe, tube, angle, channel and flat stock. Head adjusts from flat to 15°, 30°, 45°, 60°, 75° and 90°. Shelf measures 6" × 6". Bolts for shelf sold separately.
WSCRADLE17Pipe Clamping ToolWill hold pipe up to 17" diameter. This will bolt to Platen surface or WSSHELF. It can be used with WSCHAINvISE. If bolting to Platen surface, this cradle will
hold your work piece parallel to the sides of Platen.11 lbs. $199.00
WSCHAINVISEVise Grip with flexible, adjustable chain. For use with our WSCRAdLE17 or WSCRAdLE6.3 lbs. $27.00
WeldsAle offset, square head bolts & washers specially made for use with exclusive Weldsale
“Cast-in sockets” on bottom of every square holeWS8 (1 lb.) 4¼" long × ¾" dia., 3" thread. $10.00WS7 (1.5 lbs.) 5¾" long × ¾" dia., 3" thread. $10.50WS6 (2 lbs.) 10" long × ¾" dia., 5" thread. $11.00
hex head bolts, nuts & washersstandard hex head boltsWS12 (2 lbs.) 4¾" long × 1" dia. for bolting Platens together. $10.00WS13 (2.5 lbs.) 6½" long × 1" dia.for bolting Platens down to stands. $11.00
WSLC8 Large Lever ClampFast action clamp with quick release.Clamp force: 1200 lbs. Clamps from 0" to 12" Throat depth: 5½" 5 lbs. $65.00
WSLC4 Small Lever ClampFast action clamp with quick release.Clamp force: 660 lbs.Clamps from 0" to 8" Throat depth: 4"1½ lbs. $55.00
used platens
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
pp. 2–5
downdraft
systems
cutting tablespyram
idsm
agnetsused
platensp. 13
pp. 14–15 pp. 16–17
pp. 18–19 tooling
pp. 6–10
cubes, kneestowers & tom
bstonesp. 11
11
all square holes are standard 1¾" square with cast-in sockets for tooling. all slots are ⅞" wide to allow for standard WS8 bolts (¾" dia.)
WeldsAle Cubes, tombstones, toWers & Knees: stackable for increased elevation
WSKNEE1012 Weldsale Knee10" long slotted base × 12" high × 4" wideCast iron 1¾" square holes with cast-in sockets.25 lbs. $185.00
WSTOWER12B Weldsale Tower 4" wide × 6 " deep × 12" highCast iron 1¾" square holes with cast-in sockets and also slots for bolting down to Platen.30 lbs. $199.00
WSANGLE444 Pipe Clamping Tool4" x 4" x 4" angle plate or stop.6 lbs. $89.00
WSCORNER12Corner Fit Up ToolGreat for establishing and squaring up corners of your weldment. bolt down arrangement allows you to place this corner wherever you need it, at whatever orientation to the sides of Platen. Works great with WS30 Mitre Clamp.40 lbs. $195.00
WS31C90°Angle Plate10" Long × 8" Deep × 8" High• Traditional workhorse
of machine shop trade has similar uses on Weldsale Platens.
• Typically used to provide a machined vertical surface anywhere on Platen.
25 lbs. $199.00 Please note: two offset square head bolts are included
with this angle plate at no additional charge.
WSTOMB12 Weldsale Tombstone12" wide × 12" high × 4" deepCast iron with slotted base and 1¾" square holes.62 lb. $219.00
WS12CUBE 12" × 12" × 12" Cast Iron Platen Cube Three rows of 1¾" (standard size) square holes per side. Excellent for assorted tasks: as an Angle Plate, a risor block for tooling (to elevate tools for increasing the clamping envelope), as a stop for weldments and also as a risor to elevate parts of your weldments as needed. Cube has slotted holes on one side for bolting to Platen surface. The sixth side is open. Weldsale standard tooling fits the square holes.Square holes are 1¾" square on 3½" centers.125lb. $315.00
either Ws12CUBe or WstoMB12 can be used as Mini-Platens and as
“outriggers” alongside standard Platens.
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
12
WeldsAle classic tools WS4Arm Clamp
• Arm Clamps are bolted down tightly to Platen for vertical clamping.
• Platen hole size and thickness determine proper mounting bolt. Call for details.
Clamping Envelope: 0" to 3¼"Throat: 2"WS4 7.5 lbs. $104.00
WS1AWS1A Mini
Gooseneck Hold Down Dogs
• WS1A is our traditional dog for heavy duty clamping.
• WS1A Mini is a smaller, heavy duty clamp for tight/confined areas.
• Either clamp available for use with older, used Platens.
WS1A 17.5 lbs. $62.00WS1A Mini 8 lbs. $46.00
WS3 Bending Postbending Posts are used for bending or straightening with horizontal clamps.11.5 lbs. $68.00
WS38Platen Vise 180° Swivel Base vise includes connector plate and 2 bolts to attach vise to Platen. (Part no. for Connector Plate is WS38PLaTe)•5½" jaw width, 6" jaw opening. 180° rotating base. 40 lbs. $249.00
WS3BD Bolt Down Bending Postbending Posts are used for bending or straightening with horizontal clamps.11.5 lbs. $112.00
WS2Tapered Drift Pin Tapered drift pins are used as stops. 9 lbs. $58.00
WS5A90° Horizontal Clamp9.25 lbs. $112.00
WS5B 45°Horizontal Clamp9.25 lbs. $117.00
WS111 Conical Rising Block Conical rising block allows plasma and flame cutting on Platen.
• Used to elevate plate to permit flame cutting or preheating of plate over Platen.
• For 1¾" square holes only2 lbs. $6.90 ea.
WS10Heel WedgeMuch like a set up wedge, the heel provides a surface for pounding the wedge into place and also for prying the wedge out.1.5 lbs. $12.50
ChOOSE FROm OUR ASSORTmEnT OF diFFEREnT ClAmPS And TOOlS FOR yOUR jOb!
foR 1¾" sqUaRe Holes. (For 1½" and 1⅝"square holes See Page 17.)
PriCes effeCtive MArCH 19, 2012
toolingpp. 6–10
magnets
p. 13platens
pp. 2–5
downdraft
systems
cutting tablespyram
idscubes, knees
towers & tombstones
used platens
pp. 14–15 p. 11
pp. 16–17 pp. 18–19
13
WS20B8090° Inside Corner Magnetic Clamp
• Clamp and align in one step.• Welder can work alone,
eliminating a second operator holding a T-square
5 lbs. $316.00
WS21B81 90° Outside Corner Magnetic Clamp
• Magnets allow one welder to save time when holding parts off the surface of the table.
• All magnets have substantial 100 lb. holding capacity. (Not designed for lifting.)
5 lbs. $310.00
WS22B80AAdjustable Magnetic Inside Corner Clamp
• Holding surfaces are machined and can be set from 45° to 90° using built in scale.
• Layout, fit-up, and welding can beachieved in one step, by one person.
5 lbs. $396.00
WS223 Magnetic V-Block with On/Off Switch excellent for holding pipe, tubing and angle. Can be used as is, or with one of our bolt down bases to elevate the Magnetic v-block above the table surface. Magnetic force works on v-block top, sides, front, back and bottom. (all six sides!)6.5 lbs. $303.00
WS210Chunky Magnetic Square 3¾" deep × 4⅜" high × 1½" thick. This magnet has an average pull of 100 lbs. Magnetic surfaces hold work firmly at 90°, 45° and 135° angles. It includes a “T-Handle” lever adjacent to one magnetic surface to break this magnet off of the weldment.2.75 lbs. $50.00
WS211Compact Magnetic Square 3⅜" deep × 3⅜" high × ⅝" thick.This magnet has an average pull of 55 lbs. very compact to allow this magnet to fit into tight spaces. Magnetic surfaces hold work firmly at 90°, 45° and 135° angles.0.75 lbs. $10.00
WS212Magnetic Square 3¾" deep × 4⅜" high × ¾" thick.With enclosed construction to prevent metal filings and dirt from getting into the magnet, making it easier to clean, this magnet has an average pull of 57 lbs. Magnetic surfaces hold work firmly at 90°, 45° and 135° angles.1 lbs. $25.00
WS214Fixed Magnetic AngleA heavy duty magnet with two independent on/off switches.Holding force of approximately 50 lb. on each face. designed to hold plate, tube or pipe. Quick action on/off switch facilitates easy set up and removal of the magnet. 7 lbs. $231.00
WS215 Adjustable Magnetic AngleA heavy duty magnet with two independent on/off switches. The switch on each magnet makes them much easier to position and safer to use. Holding force of approximately 50 lb. on each face. designed to hold plate, tube or pipe. 5.5 lbs. $256.95
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
magnets
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
PriCes effeCtive MArCH 19, 2012
why use a downdraft ventilation/exhaust system?
• Retrofit is available for most existing Platensand stands. Please phone for full retrofitting information.
• Operator friendly–the welder does not need to move an extraction arm.
• Operator can make long welds without stopping to reposition a smoke exhaust arm.
• The downdraft principle (moving smoke away from the welder) is in keeping with OSHA guidelines.
• Applicable for any process — MIG, Flux-Cored, Stick, TIG, Plasma Cutting, Oxy-Acetylene cutting, Arcair gouging, and grinding.
• Especially suitable for galvanized and stainless welding.
Our goal is to capture approximately 70% of the smoke and fumes generated at least 12-18" above the Platen surface. Efficiency increases as the square holes are covered over by your weldment and plugged with clamps and tools. Field tests show that Weldsale downdraft systems do not affect the shielding gases in MIG welding operations.We constantly seek to improve our products. This is the third generation of our downdraft systems. It works better than our previous designs. Weldsale Company supplies only industrial grade pipe, ducting and elbows. We also supply pipe hangers and a pipe coupling for this suggested layout. The exhaust blowers are industrial grade and have weather resistant covers.Customer must supply their own electrical starter components and power cable. (Larger size units will also need a starter motor.)
A
b
C
d
e
f
downdraft ventilation/exhaust systemAir exhausting system
3rd generAtion design: tried And true!
Systems pull smoke and fumes down through the Platen’s square air holes!
Excellent for welding or hand-held plasma cutting, using pyramids on Platens.
BECausE it WoRks!
pleAse speCifY SIDE OF PLATEN FOR DUCTWORK/AIR TAKE OFF FOR THE FOLLOWING SIZES:
2½' × 5'3' × 6'5' × 6'5' × 8'
5' × 10'Shortside or Longside.
14
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
Please Note: Specify which side of Platen for exhaust takeoff (eg. 5' side or 8' side).
Ws36dd 3' × 6' downdraft A. WS36D 3' × 6' Weldsale Platen
(Light duty)
B. WS36DDS Steel Stand, Plenum, diffuser box
C. WS36RP Round Spiral Pipe 10" dia. x 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS36DE die-stamped Elbows, 90°, 2 pcs. supplied
E . WS36SPR Spun Reducer, 1 pc. supplied
F. WS36EB Exhaust blower, 2 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
platenspp. 2–5
cutting tablespyram
idsm
agnetscubes, knees
towers & tombstones
used platens
p. 13p. 11
pp. 16–17 pp. 18–19
toolingpp. 6–10
downdraft
systems
pp. 14–15
Ws510dd 5' × 10' downdraft A. WS510B 5' × 10' Weldsale Platen
B. WS510DDS Steel stand, Plenum, diffuser box
C. WS510RP Round spiral pipe16" dia. × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS510DE Gored elbows, 90°, 2 pcs. supplied
E. WS510SPR Spun reducer
F. WS510EB Exhaust blower, 5 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
Ws58dd 5' × 8' downdraft A. WS58B 5' × 8' Weldsale Platen
B. WS58DDS Steel Stand, Plenum, diffuser box
C. WS58RP Round spiral pipe 16" diameter × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS58DE Gored elbows, 90°, 2 pcs. supplied
E. WS58SPR Spun reducer, 1 supplied
F. WS58EB Exhaust blower, 5 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
Ws56dd 5' × 6' downdraft A. WS56B 5' × 6' Weldsale Platen
B. WS56DDS Steel stand,Plenum, diffuser box
C. WS56RP Round Spiral pipe 12" diameter × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS56DE die stamped elbows, 90°, 2 pcs. supplied
E. WS56SPR Spun reducers,1 pc. supplied
F. WS56EB Exhaust blower, 3 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
Ws55dd 5' × 5' downdraft A. WS55B 5' × 5' Weldsale Platen
B. WS55DDS Steel Stand, Plenum, diffuser box
C. WS55RP Round Spiral Pipe 12" diameter × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS55DE die-stamped Elbows, 90°, 2 pcs. supplied
E. WS55SPR Spun Reducers, 1 pc. supplied
F. WS55EB Exhaust blower, 2 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
Ws44dd 4' × 4' downdraft A. WS44B 4' × 4' Weldsale Platen
B. WS44DDS Steel Stand, Plenum, diffuser box
C. WS44RP Round Spiral Pipe 10" diameter × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS44DE die-stamped Elbows, 90°, 2 pcs. supplied
E. WS44SPR Spun Reducer, 1 pc. supplied
F. WS44EB Exhaust blower, 2 hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
Ws25dd 2½' × 5' downdraft A. WS25B 2½' × 5' Weldsale Platen
B. WS25DDS Steel Stand,Plenum, diffuser box
C. WS25RP Round spiral pipe 8" diameter × 60" long. 3 pcs. supplied, plus 2 pipe hangers, 1 pipe coupler
D. WS25DE die-stamped Elbows, 90°, 2 pcs. supplied
E. WS25SPR Spun Reducer, 1 pc. supplied
F. WS25EB Exhaust blower, 1½ hp. 3 Phase, 230/460v. 60Hz
Complete sYstem… Call for Prices
15
WeldsAle downdraft systems pull smoke and fumes down through the Platen, away from the welder’s face
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
PriCes effeCtive MArCH 19, 2012
Call for available sizes and pricing.
we have quality, used 5'×5' platens with blAnCHArd ground top surfacesvariety of hole sizes and patterns available.
5'× 5' ROwS On PERPEndiCUlAR
CAst iron!
Weldsale has over 48 years experience selling used Platens. Most used Platens are 5' × 5' and have no brand name. (they are usually not Weldsale brand Platens.) We usually have several different designs available. These Platen designs will differ by hole pattern/configuration, and whether they have support ribs on the underside, holes in the skirts for bolting together, etc.Please let us know if you already own older Platens. We will sometimes be able to match the design of your used Platens. (There are many, many different designs of used Platens.) Other sizes of used Platens are also often available. Please call for details.Most Weldsale flextooling must be modified to fit used Platens. We typically stock this modified tooling for immediate shipment. It will work well on used Platens. See page 17 (opposite).
Typical used Platens have 1½"or 1⅝" square holes. Typical new Weldsale Platens have 1¾" square holes.When you are ordering tooling for your Platen, please check the size of your Platen’s square holes. This need not be precise, just a close approximation–but check by using a ruler, not by eye.
example of ordering tooling for used platens:
WS1ASP …for Platens with 1½" or 1⅝" sq. holes.
WS5ASP …for Platens with 1½" or 1⅝" sq. holes.
WS16-112 …for Platens with 1½" square holes.
WS16-158 …for Platens with 1⅝" square holes.
VArietY of Hole sizes And Hole pAtterns AVAilAble
5'× 5' ROwS On diAgOnAl
f.o.b. shipping point
16
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
these new tools work for used platensplatens
pp. 2–5
cutting tablespyram
idsm
agnetscubes, knees
towers & tombstones
used platens
p. 13p. 11
pp. 16–17 pp. 18–19
toolingpp. 6–10
downdraft
systems
pp. 14–15
Part No. DescriPtioN Price refer to Page
WS1ASP Gooseneck Dog $62.00 12
WS2 Tapered Drift Pin $58.00 12
WS3SP Bending Post $69.00 12
WS4SP Arm Clamp $111.00 12
WS5ASP Horizontal Clamp 90 deg. $113.00 12
WS5BSP Horizontal Clamp 45 deg. $117.00 12
WS6SP 10"Bolt, Nut, Washer $15.00 10
WS7SP 5¾" Bolt, Nut, Washer $15.00 10
WS8SP 4¼" Bolt, Nut, Washer $15.00 10
WS38 Vise with Connector Plate $249.00 12
WS10 Heel Wedge $12.50 12
WS16-112 Vertical Clamp 9" $159.00 6
WS16-158 Vertical Clamp 9" $159.00 6
WS16-112LR Long Reach Vert. Clamp 9" $169.00 6
WS16-158LR Long Reach Vert. Clamp 9" $169.00 6
WS16-112-20 Vertical Clamp 20" $199.00 6
WS16-158-20 Vertical Clamp 20" $199.00 6
WS16-112-20LR Long Reach Vert. Clamp 20" $209.00 6
WS16-158-20LR Long Reach Vert. Clamp 20" $209.00 6
WS26-112 Vert. Pipe Clamp 6.5" $209.00 7
WS26-158 Vert. Pipe Clamp 6.5" $209.00 7
WS26-112LR Long Reach Vert. Pipe Clamp 6.5" $219.00 7
WS26-158LR Long Reach Vert. Pipe Clamp 6.5" $219.00 7
WS26-112-20 Vert. Pipe Clamp 18" $249.00 7
WS26-158-20 Vert. Pipe Clamp 18" $249.00 7
WS26-112-20LR Long Reach Vert. Pipe Clamp 18" $259.00 7
WS26-158-20LR Long Reach Vert. Pipe Clamp 18" $259.00 7
WS18-112 Horizontal Clamp 13" $199.00 6
WS18-158 Horizontal Clamp 13" $199.00 6
WS28-112 Horiz. Pipe Clamp 13" $229.00 7
WS28-158 Horiz. Pipe Clamp 13" $229.00 7
WS30-112 Mitre Clamp $289.00 6
WS30-158 Mitre Clamp $289.00 6
ALSO: ALL Magnets work great on Used Platens. (See p. 13)All small components (Knees, Towers, Angle Plate) also work great. (See p. 11) (They will use "SP" bolts as listed above.)Above pages refer to pictures of tools sized to fit 1¾" square holes.WS111, WS12 or any bolt down tool typically do not work on Used Platens.
Measure the SIZE of the square holes on your old Platens, if you already have Platens and need more tools. Also measure the thickness of your Platens through the square holes.
foR examPle: WS16-112 fits 1½" square holes and WS16-158 fits 1⅝" square holes.WS5ASP fits either 1½" or 1⅝" square holes.
see pgs. 6–12 for tools that fit 1¾" square holes.The “sP” suffix on some tools indicates special machining that make these particular tools fit.
if you alreaDy have oNe of these,
see what Number is stamPeD here
17
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
PriCes effeCtive MArCH 19, 2012
WeldsAle flAme-CleAr pYrAmids increase your profits
working advantages of using WeldsAle flAme-CleAr pYrAmids
xno more of tHis!
level plate equals square cuts which
equals better fit up.
Plate can't weld itself to cross supports and
dross blows away freely. weldsale Pyramids improve cosmetics of cutting table.
Avoid blowbacks, lost cuts and lost time!
xwithout pyramids flame blows back into tip at cross support.
Weldsale flame-Clear Pyramids are shipped by either UPs or Common Carrier Class 50. specifications subject to change without notice.terms: Net 30 Days. foB: Shipping Point.
pArt lbs.oVerAll
dimensionsslot
HeigHt WeigHt 1-39 40-99 100-249 250-upRB79DA 2¼" x 2¼" x 3¼" 1" 1lb. 15oz. $7.45 $7.08 $6.71 $6.33RB53DL 2⅛" x 2⅛" x 33/16" 1" 1lb. 12oz. $7.45 $7.08 $6.71 $6.33RB58BE 2" x 2" x 4¼" 1⅞" 2lb. 10 oz. $8.80 $8.36 $7.92 $7.48RB916XL 4⅛" x 2⅝" x 6" 2" 7lb. 4oz. $18.20 $17.29 $16.38 $15.47
rb79dA duAl slot
fits ⅜" & ½" supports
rb53dlduAl slot
fits ¼" & 5/16" supportsrb916Xl
fits ½" supportsrb58be
fits 9/16" & ½" supports
“everything under the torch gets destroyed.”Weldsale flame CleaR PyRamids are designed to extend the life of your Cutting Table. Their fewer points of contact assure that the cross supports will never be cut (as long as you continue to use the Pyramids). The Pyramids themselves (being made of cast iron) do not easily burn, even when the torch makes a “bulls eye” pass over the point of a Pyramid. (Note: Oxy-Fuel does not easily cut cast iron and the Plasma torch travels so fast, it does minimal damage.)
You install them by simply setting them on the cross supports. We recommend you place Pyramids about 6" apart. However, the size of the parts you are cutting often dictates the distance you place them apart. They can be placed right next to each other or as far apart as you wish; whatever is appropriate to the parts you are cutting. (Note: if you place them too far apart, on very thin material for instance, the plate may belly and your part size–and kerf!!–may be affected.)
The following information will help us to determine which Pyramids are best for you:
• Do you already use Weldsale Flame Clear Pyramids?
• What is the thickness of your existing cross supports?
• Do you load and/or unload your plate with magnets?
• Will you want to slide the Pyramids back and forth along the cross supports or fix them in place?
• Is your existing Cutting Table a Dry, Downdraft or Water Table?
save money!! Note: On very large tables, the number of Pyramids can easily run into several hundred or even thousands. On highly repetitive cutting, we recommend you run your cutting program, with no plate loaded, and follow the torch along, pushing or pulling Pyramids out of the path of the torch. This will greatly extend the life of these Pyramids. Get your money’s worth!
18
weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
pp. 2–5m
agnetscubes, knees
towers & tombstones
used platens
p. 13p. 11
pp. 16–17 tooling
pp. 6–10
downdraft
systems
pp. 14–15
cutting tablespyram
idspp. 18–19
19
taller, stronger, simpler, cheaper. We build them for regular duty or heavy duty applications. Weldsale Cutting tables can be used with or without pyramids.
Options include:• A central support for much greater strength
(Heavy duty Cutting Table)• A sloped tray—below the table—to bring the
dross, debris and cut parts to one side.
It will be helpful for us to know the following, so we can quote you promptly and correctly:
• How do you load and unload your Plate? (eg: Overhead Crane? Forklift?)
• do you plan to use Flame Clear Pyramids on your table?
Cross supports are easily replaced.
Would you like a different size table than those listed? Please call for pricing.
WeldsAle flame cutting tablesCompletely redesigned…
pArt number
WeigHtW/o pYrAmids
priCeW/o pYrAmids
pArt number
WeigHtWitH pYrAmids
numberof pYrAmids
priCeWitH pYrAmids
WS44TABLE 410 lbs. $1025.00 WS44TABLE-PYR 510 lbs. 55 $1394.00WS46TABLE 515 lbs. $1270.00 WS46TABLE-PYR 690 lbs. 85 $1840.00WS48TABLE 800 lbs. $1354.00 WS48TABLE-PYR 1010 lbs. 115 $2082.00WS58TABLE 880 lbs. $1480.00 WS58TABLE-PYR 1160 lbs. 138 $2355.00
WS58TABLEHD 940 lbs. $1564.00 WS58TABLEHD-PYR 1220 lbs. 138 $2438.00WS510TABLE 960 lbs. $1673.00 WS510TABLE-PYR 1310 lbs. 174 $2775.00
note: We also sell Water Tables and Downdraft Cutting Tables for Plasma and Oxy-Fuel Cutting. Call for details and pricing.
•Movable Cross Supports and Movable Pyramids•Bolt together extensions available•Tables are built to order. Custom sizes available.•Replacement Supports available.
flAme Cutting tAble Ws46tAble 4' × 6'
flAme Cutting tAble Ws58tAbleHd 5' × 8' (with heavy duty option)
Weldsale Cutting tables ship Class 85. Some assembly required.
Close up of Heavy duty option Additional center support with leg.
WS58TABLEHd with Pyramids
WS58TABLEHd without Pyramids
weldsale weldsale co. 215.739.7474 fax 215.426.1260 www.weldsale.com email: [email protected]
weldsaleWeldsale Company LLC2151 Dreer StreetPhiladelphia, PA 19125-1997
50 YeArs supplYing neW & reConditioned plAtens
strong+simple+eAsY
weld, cut, bend, straighten, saw, glue and grind…
Weldsale Platens take the abuse and give you years upon years of use.
…layout, set-up, assemble, heat, beat, measure, test & pry…
…our huge variety of clamps, tools, magnets and
components makes your job easier and faster!
catalog #WB0319 version 1.1p March 19, 2012
50years
in business for
weldsale company, llc