STRAKON Extension Manual 2014

DICAD Systeme GmbH

Extension Manual Version 2014

February 2014

STRAKONpremium STRAKONstandard STRAKONlight

This manual is protected by copyright law. All rights reserved. No part of this manual may be duplicated, translated or amended without the express written consent of DICAD Systeme GmbH. DICAD Systeme GmbH reserves the right to alter or revise this publication at any time without prior notice. DICAD Systeme GmbH accepts no liability except as set forth in its General Terms and Conditions The instructions contained in this manual shall not be construed as a warranty of particular product capabilities.

© 2014 DICAD Systeme GmbH (www.dicad.de)

STRAKON 1

Contents Installation Instructions 4

Part 1 · Basics 8 User Interface 8

Fresh New Look for the STRAKON Dialog Boxes 8 Edit Lists in Dialog Boxes 9 Search in Dialog Boxes 9

Menus 10 Toolbar 12 Function Toolbar / Additional Function Toolbar 12 Context Menu 12

Part 2 · Configurations 13 External Settings 13 Settings 13

Simplified Call-Up of Dialog Boxes 13 General Settings 13 Master Data 15 3D Design 16

File Administration 17 General 17 Handling 18

Material Administration 20 Material Name 20

Part 3 · Basics 21 Drawing Data 21

Switch on/off Margin 21 Save Drawing in Library / Create New from Library 21

General 21 Save in Library 21 New from Library 23

Create Drawing Set 23 Drawing Administration 24

Create Drawing Set / Mark Drawings from Drawing Set 24 Display all Drawings 25 Layers 25

Selection of Layers using the Dialog Box 25 Back-up Levels 26

General 26 Settings 26

Undo / Redo 27 General 27 Undo 27 Redo 27

Part 4 · Inputs/Input Helps 28 Pointer Commands 28 Screen Sections - Pan 28 Commands 28

ARBWECHS 28

Part 5 · 2D Design 29 Lines 29

Settings 29 Modify Lines > Global 29

Dimensions 30 General 30

Version 2014 © DICAD Systeme GmbH

2

New Dimension Types: Slope Dimension, Polygon Dimension 30 Settings 31 Direction of the Dimension Line using SmartClick 32

Text 32 Permanent Text Manager 32 Text Manager in Global Modification 33

Formatted Texts 33 Text Takeover from the Drawing Data 33

Hatchings / Colored Areas 33 Section using Quick Mode 33

Prefab Item Numbering 33 Insert Schedule 33

Part 6 · 3D Design 34 Walls 34

Sandwich Wall 34 Flex-Parts / 3D Built-In Parts / 3D Body 35

Create 35 Flex-Parts 36

General 36 Place Flex-Part 38 Individually Modify Flex-Part 39 Edit Flex-Part in the CubeViewer 39

CubeViewer 40 General 40 Functions of the Icon Bar 40 Status Bar 43 Further Operating Options in the CubeViewer 43

Modify 3D Views 44 Edit Section 44

Part 7 · Design Aids 45 Drawing Variants 45

Length of the Name 45 Changed Function Toolbar and Additional Function Toolbar 45

Template 45 Select Master Data 45 Insert from PDF 45

Part 8 · Edit Element 46 Delete / Modify 46

Individually in current function / Individually Free 46 Modify Section 46

Search Selectively 46

Part 9 · Reinforcement 47 General 47

Settings for Reinforcement Texts 47 Move Non-Linked Main View 47 Input Mask for Bending Shape 47 Item Reinforcement Check 48 Reinforcement Check Count Factor 49

Rebar 50 Offset/Bending at the Start and End of the Main View 50 Lay Count Views 50 Insert a Recess into a Laying 51 Bar Representation as Symbol in Count View 52 Modify Individually 52

Meshes 54 Settings 54 Renaming 54 Laying on a Line using SmartClick 54

© DICAD Systeme GmbH Version 2014

STRAKON 3

Enter Count View in the Laying Field (CV Laying) 55 Difference Schedule 57 Modify Mesh Type in Laying 57

AdHoc Reinforcement 58 Insert using Comfort or Classic 58

Rebar Design Mesh 58 3D Reinforcement 59

Basics for 3D Reinforcement 59 3D Reinforcement Check 61 Project Steel Totals 63

Settings 63

Part 10 · Built-In Parts 64 General 64

Length of the Name 64 Changed Function Toolbar and Additional Function Toolbar 64

3D Built-in Parts 66 General 66 Calling up the Function 66 Place 68 Create 68

Part 11 · Break Down 69 Wall/Ceiling General 69

Wall Setting 69 Wall/Ceiling Setting 70

Wall 71 Lattice Girder Collision Check 71

General Laying 72 Settings 72

Part 12 · Outputs and Interfaces 73 Publish / Mail Drawing 73

Publish 73 Manual Unitechnik Export 73

HPGL/PDF File of the Element Drawing 73 Print 74

Direct Drawing 74


4 Installation Instructions

Installation Instructions Contents

Important Information 4 System Requirements 4 Windows Vista/7/8/8.1 4 Windows XP 4 IMPORTANT ! Shared data access 4 Initial, Parallel and Update Installations 5

Installation 5 License 6

Version License for the Dongle 6 Licensing the Modules for the Computer 7 Registering the Unlock Code 7

Important Information System Requirements Operating system Windows XP, Service Pack 3 / Windows Vista *, min. Service Pack 2

Windows 7 *, min. Service Pack 1, Windows 8/8.1 *

* 32 or 64 Bit Version

Screen resolution min. 1280 x 768 pixels

Products: - .NET runtime modules 4

- Products from Microsoft® Office >2000 (for outputting lists to Excel)

If the set-up program cannot find the .NET 4.0 runtime modules and/or runtime libraries for Visual C++ 2005 and 2010 (vcredist_x86), it will offer to install them and you will have to perform this installation as User with Adminis-trator Rights.

Windows Vista/7/8/8.1 To ensure that STRAKON will be able to run, the installation must not be made in paths with restricted access rights, e.g. c:\windows, c:\Programs, C:\Programs(x86), C:\ProgramData or C:\User.

We recommend you use the prompted path C:\CAD.Programs\. !

Windows XP Advance information: From the STRAKON Version 2015 onwards we will no longer support the running of the pro-gram under Windows XP.

IMPORTANT ! Shared data access As a result of the new data structure of the file management, it is no longer intended that shared data access for the Version 2014 and versions lower than 2014 be permitted to the file management system using the following func-tions:

• Additional programs, macros, symbols, details, built-in parts, element break down, external files

• Reference Views

(For further details on the new file management system, see Part 2 · Configurations, File Administration, page 17)


STRAKON 5

Initial, Parallel and Update Installations Initial installation If STRAKON is not available on the computer, or only in a version lower than 5.2, then an initial installation will be automatically performed. That is, unless a license has been enabled, automatically licensed for 10 days as a demo version. After this, you can start STRAKON without a license in Viewer Mode.

Parallel and update installations If STRAKON is available on the computer in a version lower than 2014 or higher than 5.2, you can choose between a Parallel or an Update Installation.

Parallel Installation As an option, the settings of an installed 2013 version can be taken over. The following are taken over:

Plotter/printer drivers and diversion files (not STRAKON’s own files), tablet configuration, screen settings, layer sets, colors, editor settings, Excel template files, images from the template directory, input units, text modules, title block data, back-up file (secur.sic), settings for data export (PPS, BVBS, etc.), default sets, translation files for the DWG/DXF import/export, dialog settings for back-up levels, element breakdown (all SYS files), settings for automatic snapping to points, einbau-s.dat for PPC export, definition files for design meshes and settings from Settings > Basic Settings. All files are copied locally into the standard directories of the 2014 version.

Update Installation Select the version onto which you want to install the 2014 update. If your version is lower than 5.2, please request the STRAKON CD 5.2A, then conduct the update up to version 5.2A and restart the installation of the 2014 version.

We recommend you perform the installation with the user-profile set as the Administrator or User with Administra-tor Rights. A normal user will require the administrator’s password. An update must be performed using the same user-profile as was used for the initial installation. The chosen installation path must not contain any accented letters or special characters.

Perfect functioning is only guaranteed if the user is given full access to the installed directories and working directo-ries of STRAKON

Installation 1. Select the language and accept the license agreement.

2. Select between Update and Parallel Installation. With the parallel installation, you can optionally take over the settings from the 2013 version.


6 Installation Instructions

3. If conducting an Update, select the existing version onto which the update is to be installed As an option, you can delete the old program folder from the start menu. A new folder with the current entries is automatically created.

4. As an option, a link to STRAKON 2014 can be created for you on the desktop.

5. Continue by following the instructions in the installation dialog prompts.

License Version License for the Dongle A version license is not usually necessary for the dongle used in the context of the service agreement!

Check the version number in the dongle via: Start > Programs > DICAD 2014 > Dongle test:


STRAKON 7

Requesting a version license for the dongle with pre-2014 versions Open the license via Start > Programs > DICAD 2014 > Unlock software:

Click on Request, complete the input boxes and send the request to the responsible customer services department.

Licensing the Modules for the Computer It is only possible to unlock software (e.g. steel construction variants etc.) via an unlock code for the computer in question. Open the license via Start > Programs > DICAD 2014 > Unlock software:

Mark the modules, click on >> and Request, complete the input boxes and send the request to the responsible cus-tomer services department.

Registering the Unlock Code Open the license via Start > Programs > DICAD 2014 > Unlock software, enter the unlock code in capital letters and click on Register.

We wish you every success in all your work with the 2014 version!

Should you have any further questions, please do not hesitate to contact us.

Your DICAD Support Team


8 Part 1 Basics

Part 1 · Basics

User Interface Fresh New Look for the STRAKON Dialog Boxes As in previous updates, in this new STRAKON 2014 version familiar dialog boxes are given a fresh new look while retaining the same user prompts.

Example:


STRAKON 9

Edit Lists in Dialog Boxes Filter Lists The filtering has been simplified for the selection of the display of lists.

For this, please enter the letters and/or characters of the filter criterion into the input box

Delete filter Display the complete list again after filtering

The filter criterion in the input box will then be deleted

Filter Display the list in accordance with the filter criterion

Using the context menu (right mouse key) you specify through the selection of the criterion in which column filtering will take place, e.g. filter in the font input box in the column Description in accordance with the criterion std. It is possible to switch on several criteria at the same time.

Quick filter By switching on this option you can obtain a selected display of the list directly while entering the filtercriterion.

Search in Dialog Boxes In order to be able to more quickly find an option, such as settings or global modifications, you can now search for it in the dialog boxes. The search function is opened using the key combination Ctrl+F. Please ensure that you have marked an option in the column beforehand.

You repeat the search by pressing the function key F3.


10 Part 1 Basics

Menus The menus have been rearranged or have been expanded in their functions and functions have been renamed.

Menu File

The menu has been expanded and rearranged:

New:

New from library Save in library Create drawing set Import / Export > Import PDF (see Part 7 · Design Aids, Template, Insert from PDF, page 45)

Discontinued:

The function Working Directory and also the functions GEO Import, GEO Export, Batch Export GEO, GEO > DXF/DWG and DXF/DWG > GEO in the menu Import / Export have been discontinued.

Moved:

The function Print > Parts schedule can now be found under Inter-faces.

Menu View

The menu has been expanded:

New:

Display pen weight


STRAKON 11

Menu Reinforcement The menu has been rearranged:

New:

Rebar design mesh 3D reinforcement 3D reinforcement check

Moved:

The functions Rebar administration and Mesh administration can now be found in the menu Settings > Administration.

Menu Settings

The menu has been expanded and rearranged:

New:

Administration

Reinforcement > Project steel totals

The function material administration can now be found in the menuSettings > Administration > Material.

Menu Window

One function has been renamed:

New: Display all drawings Previously: Show all windows


12 Part 1 Basics

Toolbar The toolbar has been expanded and one icon has been renamed:

New:

Accessories: 3D built-in parts

General reinforcement: Item reinforcement check

General reinforcement: 3D reinforcement

General reinforcement: 3D reinforcement check

Rebar: Reinforcement check count factor

Renamed:

Window: Display all drawings

Function Toolbar / Additional Function Toolbar

As additional information on the pen weight the respective pen number is displayed in brackets.

Context Menu The context menu has been expanded to include the functions Display pen weight (see Part 2 · Configurations, General Settings, Display: Display Pen Weight, page 14), Delete individually, Delete last input, Modify indi-vidually and Copy individually.


STRAKON 13

Part 2 · Configurations

External Settings The entry Graphic Settings has been removed from the external settings.

Settings Simplified Call-Up of Dialog Boxes The dialog boxes for selection can be directly opened in the settings Master data and Schedule headers and draw-ing data texts by clicking in the appropriate right column.

General Settings General Settings The category General settings has been extended to include the settings for the Drawing to/from library:

Optionally, you can switch on the protocol when saving to and New from library.

Save The category Save has been expanded to include the settings for the back-up levels Saved drawing level and Automatic back-up:


14 Part 2 Configurations

Output The category Output has been expanded to include the setting Selection of Windows printers in “Direct draw-ing…":

Switch the option on to open the Windows dialog box Print using Direct drawing (see Part 12 · Outputs and Inter-faces, Print, Direct Drawing, Selection of Windows Printers in “Direct Drawing…“, page 74).

Display: Display Pen Weight The general settings have been expanded in the category Display to include the option Pen weights:

Different pen weights can now be displayed on the screen. The pen weights are displayed using 1, 3, 5 or 7 pixels. You can assign the max. pen weight (mm) to the pixel values. E.g. when entering 0.25 all pen weights up to 0.25 mm will be displayed with a pen weight of 1 pixel (see above).

switched off switched on

You can display different pen weights by switching on the option Display pen weight using the Settings > General settings > Display menu and by using the context menu.


STRAKON 15

Master Data General The entries have been clearly arranged according to subject area:

New Master Data For these entries you can now specify master data names and paths:

Drawings (Library) Menu File > Save in library

3D built-in parts Menu Accessories > 3D built-in parts



Manage Settings All current master data names can be saved in a file (*.set) together with their relevant master data paths. You can select any storage location. Conversely, the saved settings can be loaded at any time.

Open Open the settings file (*.set) and take over data

Save as Save the settings in a file (*.set)

Material Administration By switching on the option Work directory when creating a new working directory, the DICAD material administration is copied to the new work directory.

3D Design The category 3D design has been extended to include the settings for the Drawing in library:

If only one Flex-Part is available, select for the naming of the Flex-Part between

Never The Flex-Part is saved to the library with its name.

Automatic The Flex-Part is saved to the library with the drawing name.

Inquires The prompt is displayed for the taking over of the drawing name.


STRAKON 17

File Administration General The file administration dialog box has been completely revised:

When calling up the function, for example Symbols, you open the administration in the additional function toolbar with the full range of its functions.

When placing and creating a file, for example Symbols, the administration has a reduced range of functions when opened in the function toolbar.

In this administration you can select files in the Selection list or by using the icon Graphical selection and, as nec-essary, by changing the Display of the catalogs or the Master data path and filter in the list.

Administrative functions, such as Delete, etc. are not active at this point.



Note: • The information in the list is read from the *.inf files of the list entries. These files are automatically created for

every list entry, for example symbol, when it is created. Missing *.inf files are created immediately on opening the file administration.

• When updating from versions lower or equal to 2013 a search is carried out for a database in the active masterdata path on the first opening of the file administration. If the database exists, the *.inf files are created together with their information.

• Because of the data format of the new file administration it should not be attempted to access the samedata directory using the 2014 version and pre-2014 versions at the same time!

Handling The handling of the file administration, for instance marking, sorting or editing, takes place analogous to the lists in comparable dialog boxes.

Catalogs The display of the symbols shown in the list depends on the selected catalogs. Open the list of all catalogs using the icon Select catalogs and choose the catalogs whose symbols should be shown:

Following this, the names of the catalogs will be displayed in accordance with the selection:

If you have selected all catalogs, All appears.

In order to quickly change in the selection list between the display of all or selected catalogs, click on the icon / Display all catalogs, on/off.

Assign Catalogs You can now assign a symbol to one or several catalogs. By selecting certain catalogs you can obtain either a rough or a detailed overview of the symbols.

Example: You assign the symbol Sections to the catalog Arrows (for a rough overview) and to the catalog Section arrows (for a detailed overview).


STRAKON 19

Replace Catalog(s)

Mark one/several symbol(s) in the selection list and click on the icon Assign catalogs (replace) to replace the catalog(s) by one or more catalogs. You can create a new catalog by entering a new name using the line New catalog:

Add Catalog(s)

Mark one/several symbol(s) in the selection list and click on the icon Assign catalogs (add) to add one or more catalogs. When doing this, you can also create a new catalog.

You can additionally overwrite (replace) one or more catalogs directly in the selection list for a marked symbol using the input box in the column Catalog or add a further or new catalog by entering a catalog name. You can enter sev-eral names at once by separating them with a comma:

Replace

Add

Master Data The selection list displays the current master data names. By opening the list you can change directly to another master data path.

Click on the icon Administer master data path to newly create, delete or change master data paths.

The administration is divided into the following columns:

Current Identification of the current master data path

The current master data path can be changed by clicking in the column

Master data name Enter the master data name



Work directory By switching on the option Work directory you create or save the data in the current working directory. The ordner.dat entry from pre-2012 STRAKON versions has been discontinued. With the STRAKON update, an existing ordner.dat entry is automatically replaced by the activated option Work directory.

Master data path Select the master data path using the Open icon or enter the directory name or data path directly. The following inputs are possible:

ebt projekt_01\ebt !110 !110\ebt j:\projekt_01\ebt

The ebt directory is located in the strakon program directory. The projekt_01\ebt data path is located in the strakon program directory. The files are located in the current working directory The files are located in the ebt subdirectory of the current working directory. The files are located on the (network) drive letter j in the data path projekt_01\ebt.

The selection or entry of a directory or data path in the network for a drive letter which does not currently exist, e.g. \\server\projekt_01\ebt, is not allowed. Adding/deleting of lines in the list is carried out analogous to Edit lists in dialog boxes.

Material Administration Material Name You can now enter a maximum of 256 characters for the name of the material.


STRAKON 21

Part 3 · Basics

Drawing Data Switch on/off Margin Select Without margin to reduce the left margin to 5mm. The drawing area will be appropriately expanded.

Save Drawing in Library / Create New from Library General You can save drawings which you wish to use as a template in a library and, as required, create a new drawing as a copy from the library in the selected working directory.

Examples of templates: • An empty drawing for formwork or reinforcement in various sheet sizes and scales including the plan head and

legends

• A working drawing with an inserted Flex-Part

• 3D layout drawing with several Flex-Parts

Save in Library Select the drawing using the menu File > Save in library and save it, optionally under a new name, in the active master data path of the Drawings (Library).


22 Part 3 Basics

The drawing contains a Flex-Part If the drawing contains one Flex-Part, you can optionally take over this into the active master data path of the Flex-Parts library using the name of the drawing:

If the Flex-Part already exists in the library under its own or the drawing's name, you can overwrite or duplicate it or cancel the takeover into the library:

The drawing contains several Flex-Parts If the drawing contains several Flex-Parts, the Flex-Parts will be taken over under their name into the active master data path of the Flex-Parts library. If these Flex-Parts already exist, you can overwrite or duplicate them or cancel the takeover into the library

Protocol After the saving process into the library is complete the protocol opens up automatically:

Note: Renamed or duplicated Flex-Parts will be immediately replaced in the drawing.


STRAKON 23

New from Library Select a drawing which has been saved as a template using the menu File > New from library and save this as a copy, optionally under a new name, in a working directory. The new drawing opens in the selected working directory.

The drawing contains a Flex-Part If the drawing contains a single Flex-Part, it will be loaded from the Flex-Parts library and taken over into the active master data path of the Flex-Parts. There you can optionally rename it using the new name of the drawing.

If the Flex-Part already exists under its own or the drawing's name, you can overwrite or duplicate it or cancel the takeover.

The drawing contains several Flex-Parts If the drawing contains several Flex-Parts, they will be loaded from the Flex-Parts library and taken over, using their own name, into the active master data path of the Flex-Parts. If these Flex-Parts already exist, you can overwrite or duplicate them or cancel the takeover.

Protocol After the creating is complete the protocol opens up automatically:

Create Drawing Set You can now pool several open drawings into a drawing set directly using the menu File > Create drawing set.

You can also create a drawing set from several open and unopened drawings in the drawing administration.


24 Part 3 Basics

Drawing Administration Create Drawing Set / Mark Drawings from Drawing Set You can now create drawing sets additionally in the drawing administration from open and unopened drawings and read off from the drawing set in order to mark these drawings.

Create drawing set Mark the drawings which you would like to save in a drawing set.

Specify a name for the drawing set which simplifies for you the choice of the drawing set for furtherprocessing (see Different Forms of Behavior in the Drawing Administration, page 24).

Mark drawings from drawing set Choose the drawing set whose drawings are intended to be marked. A list displays the contents of theselected drawing set:

Following this, in the drawing administration you can select or de-select drawings in addition to the marked drawings in the drawing set and further edit these (open, copy, print, etc.).

Different Forms of Behavior in the Drawing Administration Open the drawing administration using the menu and icon bar / in the function Publish Create drawing set To create a drawing set select drawings from one working directory.

Mark drawings from drawing set Only those drawings of the drawing set are marked in the drawing administration which are in the active working directory.

In the function Project Steel Totals / Print > Drawings > Several drawings Create drawing set To create a drawing set you can select drawings from several working directories.

Mark drawings from drawing set All drawings in the drawing set in the drawing administration are marked. You can thus immediately produce the output of the project steel totals list or carry out printing.


STRAKON 25

Display all Drawings In the menu Window the function Display all windows has been given the new name Display all drawings and the dialog box has been adjusted:

The Create drawing set and Close drawings buttons have been removed. In addition to the function Close many (= Close drawings), the function Create drawing set can now also be found by using the File menu.

Layers Selection of Layers using the Dialog Box In many of the Level functions, e.g. Assign element (previously: Swapping) or Change layers etc., you can now also select a layer directly in the List of Layers by using Select.

List of layers


26 Part 3 Basics

Back-up Levels General The savings and back-ups are now listed in a clearly arranged manner according to drawings:

The list begins with the drawing of the last saving and interim back-up. For each drawing the savings and back-ups are listed in chronological order.

An older back-up can be opened by a double-click on the relevant line or by marking it and confirming with Open.

To delete a line, mark the line and press the Del key or open the context menu by pressing the right mouse button and select Delete selection.

Settings You can now determine the settings for the back-up levels by using the menu Settings > General settings (see Part 2 · Configurations, General Settings, page 13).


STRAKON 27

Undo / Redo General The number of back-up levels in editing functions has been increased to 20.

Undo When carrying out an editing function, e.g. Copy Section, a back-up level is first created with the prefix Before, e.g. Before: Copy, which can be used for undoing . If you carry out a drawing function after the editing function, e.g. enter a dimension or create a rebar item, firstly a back-up level is created of the drawing level with the prefix After, e.g. After: Copy.

Redo Use Redo to restore undone back-up levels to their original state. When you select Undo for the first time, a back-up of the drawing level will first be created and offered up as Last level for redoing.


28 Part 4 Inputs/Input Helps

Part 4 · Inputs/Input Helps

Pointer Commands (not available in STRAKONlight) For a quicker activation of the Part elements in the editing functions Delete and Modify use the combination Ctrl+Alt and/or Alt + pointer symbol (see Part 8 · Edit Element, Delete / Modify, page 46).

Ctrl+Alt + pointer command " " Alt + pointer command " " Alt + pointer command " "

Delete individually free > Part element

Ctrl+Alt + pointer command " " Modify individually free > Part element Alt + pointer command " "

Screen Sections - Pan (not available in STRAKONlight) You can now carry out the function Pan (for moving the drawing section) by using the fitted Pen tip and by pressing the upper rocker key of a coordinate.

Commands ARBWECHS By using the command ARBWECHS in the chapter General commands you can directly change the working direc-tory for the current drawing. The selected working directory will not be displayed in the title bar of the CAD window until the drawing has been saved.


STRAKON 29

Part 5 · 2D Design

Lines Settings The dialog box for the line settings has been expanded to include the basic settings and the selection for marking.

Modify Lines > Global You can now modify here both the display of the end point of a line and the size of the cross markings.


30 Part 5 2D Design

Dimensions General The dimension types are now arranged by subject area.

New Dimension Types: Slope Dimension, Polygon Dimension Slope dimension The slope of a distance, identified by 2 dimensional points, is calculated and dimensioned.

A=… Basic angle for the calculation of the slope

The position and the geometric angle equate to the basic angle.

0° 90° 30°

When turning the geometry with a slope dimension using a section, the prompt for modifying the basic angle is made for the same difference angle. If you answer the prompt with Yes, the slope value remains unchanged. For an answer of No a re-calculation of the slope value is made.

Degree Select between Degree, Percent, Ratio and Gon.

Text Optionally you can enter a text for the slope value. Give the position of the value in the text with the # character.

Determine the distance using 2 dimension points, whereby the second point determines the position of the arrow.

Example 1: Calculation in percent


STRAKON 31

Example 2: Calculation in degrees including prefix

Note: You can determine in the settings the unit and number of decimal places for a slope dimension separately from theother dimension types.

Polygon dimension A polygon dimension consists of individual dimensions which are placed parallel to the identified dimension points. You only determine the distance from a dimension to the dimension points for the first individual dimension in the polygon. All other dimensions in the polygon are automatically placed at the same distance.

Settings In addition to the redesigned dialog box, the display of the ø character is now offered as a separate option from the selection of the type of dimension terminator.


32 Part 5 2D Design

Direction of the Dimension Line using SmartClick You can determine the direction of a dimension line by using the SmartClick function. You determine the direction of the dimension line in relation to an identified line by the method of selection when triggering the SmartClick (see marked line). A parallel position of the dimension line can be obtained by selecting the line in the lower or upper fifth (1). If you carry out the SmartClick in the central section (2), the dimension line will be displayed at a right-angle to the identi-fied line.

Text Permanent Text Manager The permanent text manager dialog box has been revised.

The operations in the right-hand dialog box area of the Text manager have changed.

Chapter Selection list of the existing chapters

Chapter administration Open and save a text manager file. Create, modify and delete a chapter


STRAKON 33

Text administration Create, modify and delete text

Text Manager in Global Modification The text manager now opens up in global modification by clicking on the button.

Formatted Texts (not available in STRAKONlight)

Text Takeover from the Drawing Data The drawing text (!xxx) and/or parts of this text (![xxx:xxx]) are now available for text entry in the dialog box Format-ted texts.

Hatchings / Colored Areas Section using Quick Mode In order to speed up the search process in a section pull the search section down from top to bottom (quick mode). Within this, all elements in the section will be automatically searched for and hatched.

Prefab Item Numbering Insert Schedule Item numbers with a maximum of 12 characters will now be considered in the lists.


34 Part 6 3D Design

Part 6 · 3D Design

Walls (not available in STRAKONlight)

Sandwich Wall In addition to a solid and double wall, the wall type Sandwich wall (a double wall with cavity insulation) is now avail-able.

Function toolbar

The relevant settings >> are shown for a sandwich wall.

Note: The values of a sandwich wall including cavity insulation will be transferred to the Break down module.


STRAKON 35

Flex-Parts / 3D Built-In Parts / 3D Body (not available in STRAKONlight)

Create (Flex-Parts / 3D Built-in parts: not available in STRAKONstandard) In addition to the definition of Layers, you can now also rotate a surface about an axis or design the part directly in the CubeModeler (not for 3D bodies).

Additional function toolbar

The creation form Rotation is not available at this point in the 3D body function.

Create via Rotation Function toolbar

Determine the axis of rotation (equivalent to the z-axis) using 2 points.


Starting angle=…, End angle=… Starting and end angle of the rotation

Example: 1. Select the points of the axis of rotation

2. Choose entry type Polygons

3. Starting angle = 0°; End angle = 360°

4. Define the window around the closed geometry


36 Part 6 3D Design

Flex-Parts (not available in STRAKONlight)

General File Format The file type of Flex-Parts has changed from *.xml to *.smd.

Note: • You can open and edit Flex-Parts with a file type *.xml in the CubeModeler. However, they can only be saved as

an SMD file using Save Flex-Part as. The function Save Flex-Part is not available here.

• You can still insert Flex-Parts with a file type *.xml into drawings. When the Flex-Part is identified using the pointer symbol "C" and selected using the function Edit, it is automatically opened as a copy in the CubeModeler with the file type *.smd and directly replaced in the drawing.

• If Flex-Parts with the same name and of both file types (*.xml, *.smd) exist in the master data path, only the Flex-Part with the file type *.smd will be displayed and/or offered in the administration, for inserting and modifying.


STRAKON 37

File Administration The file administration has now also been integrated for Flex-Parts.

In addition to the 2D image file, a 3D preview is displayed. You can use the following functions from the CubeViewer preview here:

Pan, all zoom functions, turn to the current cursor location (right mouse key), turn view in 90°steps, turn to 0°, turn using the cube, select display modes (Shift+R), hide marked objects (H) or display as transparent (T).

You can switch the 3D preview on and off in the Settings using the option Display 3D preview. If the option is switched off, you can temporarily switch it on for the marked element by a click in the 3D preview.

Function Toolbar/Additional Function Toolbar The extent of the toolbars and the function names have been changed.

Function toolbar

New: Edit Previously: Open

Moved: Place from library has been moved from under Library into the additional function toolbar.


New: Drawing schedule Previously: Schedule

New: Master data Master data name (Library) Library Administration for Flex-Parts (Library) Administration Administration for Flex-Parts


38 Part 6 3D Design

Settings As an option select the pen Nplo for a Flex-Part as a negative part (see Insert Flex-Part). You can switch on/off the item labeling of the referenced 3D built-in parts.

Place Flex-Part Select a Flex-Part using the function toolbar:

From library Select a Flex-Part from the administration (Library)

KON files which belong to the Flex-Part and which are in the directory above the library must be moved into the mas-ter data path Drawings (Library) (see Part 3 · Basics, Save Drawing in Library / Create New from Library, page 21).

From administration Select a Flex-Part from the administration

From drawing list Select a Flex-Part from the drawing list

The Flex-Part in the drawing does not have to exist in the administration or in the library.

SF01_01 The last used Flex-Part is offered for placing.

The functions Front and Negative part are now additionally available for the placement of a Flex-Part.


Top, … Placement view of the Flex-Part

Select one of the 6 standard views or determine the placement view in the CubeModeler. Close the CubeModeler with OK and place the Flex-Part into the drawing.

Negative part Toggle function for the insertion of a Flex-Part as a negative part


STRAKON 39

Use a Flex-Part as a negative part in order to cut out only one section from the Flex-Part in the drawing.

3D built-in parts Toggle function for display/hiding of the item text for the referenced 3D built-in parts

Individually Modify Flex-Part Analogous to Insert, new functions have been also added in the function toolbar to the Modify function.

Top, … Placement view of the Flex-Part

Select one of the 6 standard views or determine the placement view in the CubeModeler. Close the CubeModeler with OK and place the Flex-Part into the drawing.

Positive, Negative Toggle function

Switch between a positive and a negative part

Rename Rename a placed Flex-Part

When renaming, a copy of the Flex-Part is created in the active master data path and replaced in the drawing.

Edit Flex-Part in the CubeViewer (not available in STRAKONstandard) You can now also edit the Flex-Parts placed in the drawing in the CubeViewer (see CubeViewer, Functions of the Icon Bar, page 40).


40 Part 6 3D Design

CubeViewer (not available in STRAKONlight)

General Transparent and Hidden Objects Transparent and hidden objects in the CubeViewer remain transparent or hidden in the drawing when designing.

Functions of the Icon Bar New Icons and Functions New icons and modified user prompts are available for selection in the CubeViewer and CubeModeler.

CubeViewer

CubeViewer: 3D reinforcement

CubeViewer - Preview

CubeModeler


STRAKON 41

Open Flex-Part (Ctrl+O) (not available in STRAKONstandard) Now open IFC files (Industry Foundation Classes) in the CubeModeler. Select a material as a default for unknown materials in the IFC file or assign the materials directly.

The imported objects can be edited using all possible modification tools. As necessary, define the placementview and the placement point and save these objects as Flex-Parts.

Save Image (Ctrl+Shift+i) Save the current display as an image (JPG, PNG)

In PNG file format the background is saved as a transparent surface.

Export to drawing as an image Take over the current display into the drawing as an image (PNG) with a transparent background

The image will be automatically deposited as a file in the directory strakon\bilder under the name Cube-bild*.png.

Export to drawing as 3D line group You can take over the display of all visible objects, such as 3D reinforcement, parts and 3D parts, into the drawing as a 3D line group in 3D reinforcement and 3D reinforcement check.

Edit marked Flex-Part (not available in STRAKONstandard) You can now edit the Flex-Parts placed in the drawing in the CubeViewer. When doing this, you can use the points of all flex- and other parts as a reference, for instance when measuring for a change of height.

Mark the Flex-Part which is to be edited and click on the icon Edit marked Flex-Part. The program changes to the CubeModeler.


42 Part 6 3D Design

For clarification, the Flex-Part which is to be edited is displayed in the relevant material color. All Flex-Parts with the same name will be marked with a magenta border.

All possible modification tools of the CubeModeler are available.

After editing select OK and confirm the prompt to save the changes in the Flex-Part. The drawing will be updated, the model recalculated and the program will change once again to the CubeViewer.

Add referenced 3D built-in part (not available in STRAKONstandard) Add 3D built-in parts into a Flex-Part as a reference

When making a geometry change to the referenced 3D built-in part you only need to edit and save its source, e.g. using Edit referenced part.

If you update the Flex-Part which has been placed into the drawing, all the referenced 3D built-in parts con-tained in it will also be updated and, where necessary, the item number changed.

You define the item number of the referenced 3D built-in part for the placement in the dialog for built-in part data (see Part 10 · Built-in Parts, 3D Built-in Parts, page 66).

Add referenced Flex-Part (not available in STRAKONstandard) This icon/function replaces the icon/function Import Flex-Part. You can add additional Flex-Parts to a Flex-Part as references. When making a geometry change to the referenced Flex-Part, only its source needs to be edited and saved. If you update the main Flex-Part which has been placed into the drawing, all the referenced Flex-Parts contained in it will also be updated.

Edit referenced part (Ctrl+space bar) (not available in STRAKONstandard) You can also edit a referenced Flex-Part or 3D built-in part in the CubeModeler analogous to Edit marked Flex-Part. You save the changes directly with Save or OK to the source of the Flex-Part or 3D built-in part.


STRAKON 43

Create section (C) You can freely move the cursor for the entry of the sectioning line. If the cursor is in the immediate vicinity ofthe angles 0°, 90°, 180° and 270°, they will be automatically recognized and snapped to. You can switch this angle recognition on/off at any time by pressing the R key.

For an exact definition of the sectioning line you can snap to the points with the space bar and modify them as necessary. Hidden objects remain hidden during the definition of the section and in the relevant 3D view in the drawing.Select Edit Section for subsequent display of the objects in the 3D section (see Edit Section, page 44).

Fragment referenced part (not available in STRAKONstandard) Cancel the reference to the source and the object structure of the placed Flex-Part or 3D built-in part

You can now edit the layers using all possible modification tools of the CubeModeler.

Create cone (F7) (not available in STRAKONstandard) Create a cone via a center point and a radius

You can define the center point and radius by freehand or by entering values. After the creation you candetermine the material for the sphere using the function Fix material for marked objects.

Status Bar Entry in Box When entering in insert mode, press the Tab key now and enter the value.

Activation using the space bar is no longer possible.

Further Operating Options in the CubeViewer Pan You can now also use the arrow keys on your keyboard for an infinitely variable movement of the model.

Snap to Points For modifying points you can now, analogous to the design in the drawing, snap to the point with the space bar. Snapping using a right mouse click is no longer possible.


44 Part 6 3D Design

Modify 3D Views Edit Section If the 3D view to be modified is a section created in the CubeViewer, you can subsequently extrude the section sur-faces in the CubeModeler or move the entire section. Identify the 3D view using Modify individually free or the pointer symbol "C".

Function toolbar

If you select Edit section the CubeModeler opens up:

The section is displayed as a body in full size (depth and height). The line of sight to the section is marked for infor-mation by arrows. You can change the display of the section body and/or building model at any time by using Dis-play marked objects transparently.

Select Extrude object surface to move a surface of the section body. You can move the section body itself by using Move marked objects.

Close the CubeModeler with OK and take over the complete edited status into the drawing.

Note: Select Hide marked objects in the CubeModeler for a subsequent displaying or hiding of objects and confirm withOK.


STRAKON 45

Part 7 · Design Aids

Drawing Variants Length of the Name You can now enter a maximum of 80 characters for the file name of the built-in parts, symbols, etc. All permissible Windows characters are available for the naming.

Changed Function Toolbar and Additional Function Toolbar The function toolbar and additional function toolbar have been changed for the inserting and creating of macros, symbols, details and element break-down (see Part 10 · Built-In Parts, Changed Function Toolbar and Additional Function Toolbar, page 64).

Template (not available in STRAKONlight)

Select Master Data

"Schablonen" Current master data name

Insert from PDF (module available at additional expense)

Select Insert from PDF to insert a 2D PDF file into the drawing.

If the PDF file contains several layers, you can select the layers to be inserted.

The template displays all lines, texts and dimensions of the selected layers.

Note: All templates, except those temporarily created, will now be saved either with the drawing or to a back-up level.


46 Part 8 Edit Element

Part 8 · Edit Element

Delete / Modify Individually in current function / Individually Free You can edit parts of a line or a circle using Part element. A separation of the line or circle at the point of intersection is no longer necessary.

Function toolbar

Select Part element and identify the part (between 2 points of intersection or a point of intersection to the end of the element) of the line or circle which is intended to be deleted or modified.

Additionally use the quick entry method via the pointer symbols to edit the part elements (see Part 4 · Inputs/Input Helps, Pointer Symbols, page 28).

Modify Section Search Selectively (not available in STRAKONlight and STRAKONstandard) The toggle function Selective has, analogous to the other section editing functions, been moved to the additional function toolbar for element selection.


STRAKON 47

Part 9 · Reinforcement

General Settings for Reinforcement Texts American Text Format Switch on the option original to display the German text format (ø10/15) with the American symbol "#" for a diameter (#10/15).

Move Non-Linked Main View Now you can move a main view created using MV old with the use of Modify individually > BR or MR > Location, the menu Edit > Move individually free or using comparable pointer symbols.

Input Mask for Bending Shape The input mask for bending shapes has been revised.

Using the button you can determine a leg length in the drawing analogous to the function Measure distance.


48 Part 9 Reinforcement

Where laying exists (Top, Side) the button additionally appears, using which you can take over the side length.

Item Reinforcement Check (not available in STRAKONlight)

Enter Item Number or Select using Display Switch on the function Enter item number to select the item number using Display in the dialog or to enter directly.

Function toolbar


Rebar, standard/special meshes Select the type of reinforcement to be examined

Display Select the position using the display window

Next item Automatically mark the next available position


STRAKON 49

Reinforcement Check Count Factor (not available in STRAKONlight) You can check the count factors of all the reinforcement views in the drawing using the menu Reinforcement > Overview of rebar items > Reinforcement check count factor or the toolbar .

Determine the count factor to be checked and the reinforcement views using the additional function toolbar.


Factor … Select according to count factors = 0, > 0, = 1 or > 1

MV, CV, BR Select reinforcement views by Main View, Count View and Bar Representation

Permanent Marking is retained permanently, on/off

The selected reinforcement views remain marked for further editing of the drawing. As soon as a reinforcement view no longer matches the selected criteria during further editing, its marking will be automatically switched off.

P=… Pen for permanent marking

This switch does not appear until after the first switching-on of the Permanent function.

Item circle Mark the item number circle of the selected reinforcement



Rebar Offset/Bending at the Start and End of the Main View You can optionally mirror and copy the offset or bending entered at the end of a main view with the end leg at the beginning of the main view.

For automatic mirroring including copying of the offset and bending switch on Start=End.

Offset additional function toolbar:

Bending additional function toolbar:

Lay Count Views Calculate Bar Distance or Quantity If you wish to calculate the bar distance using nec. As [cm2/m], enter the as value with a pre-set as or AS:

The bar distance will be calculated using the selected bar diameter (rounded to 0.5cm) and offered as a default value:

If you wish to calculate the bar quantity using nec. As [cm2], enter the as value with a pre-set as or AS:

The bar quantity will be calculated using the selected bar diameter and offered as a default value:

For both entries the information on nec. As/exist. As will be displayed in the status bar.


STRAKON 51

Insert a Recess into a Laying You can insert a recess into a plane laying (A-Side, A-Plan, A-Leg) in the modify function.

Select Add recess from the additional function toolbar using the menu Reinforcement > Modify rebar individually > Count view.

Define the recess and choose the laying angle of the item to be modified (important for crosswise laying). The laying field will be automatically divided in accordance with the shape and size of the recess and designed as far as possi-ble using the existing item.

Select in succession the surfaces for further laying and enter all relevant data (item number, diameter, etc.). Further explanations can be found in the STRAKON Help: Reinforcement > Rebar > Input method for reinforcement Comfort > Lay the count view field by field (CV area).

Note: • When Quick reinforcement input is selected, modifying is made with less prompts.

• If modify is called up using the pointer symbol "C", the laying direction of the marked item is taken over as a default.

• Not all fields must be laid using rebar. End modify as required using Continue in the toolbar or using the pointer symbol "\".



Bar Representation as Symbol in Count View (not available in STRAKONlight and STRAKONstandard) You can now place the symbol for the bar representation behind the item text in an existing count view. As an option, you can switch off the side text for the symbol.

Modify Individually Modify Laying Leg Numbers (not available in STRAKONlight and STRAKONstandard) Select Modify individually > CV > Leg numbers to change the leg numbers of a bending shape for a laying. For this, select the laying to be modified and determine the leg numbers.

You can modify the leg numbers for the following types of laying:

• Laying with variable leg lengths created using

CV laying > A-Plan, A-Side or A-Leg

• Laying with constant leg lengths created using

CV laying > L-Leg CV individual > Leg

Example 1: Laying field for variable bar The leg number 0 was assigned in the laying:

When modifying the laying the variable leg numbers 2 and 4 are added:


STRAKON 53

If the table with the variable lengths exists, this will be automatically updated (see also Bar Representation Table, page 53).

Example 2: Line laying The incorrect leg number 3 was selected in the laying:

When modifying, the leg number 2 is selected:

Bar Representation Table Select Modify individually > BR > Table to modify an existing table with variable length or to display this table if did not previously exist.



Meshes Settings Design Meshes with fixed Overhang Switch on Mesh end rod (fixed overhang) to use the defined minimum overhangs (min. O1 to min. O4) in design rules when creating a design mesh. The resulting final bar distance in the mesh is additionally determined by the defined Minimum distance. i.e. if the minimum distance is not reached, the second last rod is omitted.

Renaming The term List Meshes has been renamed to Special meshes, for example in the mesh administration.

Additional terms have been renamed:

old new Load bearing direction Longitudinal direction Delivery direction Transverse direction Load bearing bar Longitudinal bar Delivery bar Transverse bar

Laying on a Line using SmartClick Identify a leg in the main view using SmartClick and determine the laying length. If the laying results in remnant mesh or if the laying length is shorter than the identified mesh, the program automatically creates the appropriate main view for it.


STRAKON 55

Enter Count View in the Laying Field (CV Laying) Function Speeded Up Using the Comfort entry method you can now create a laying with just a few clicks. You simply define the laying field, select the type of mesh and confirm the displayed laying.

After defining the laying field (external geometry) you define recesses using the additional function toolbar or select the type of mesh.

Function toolbar

The function From administration (previously: Mesh Administration) has been integrated into the function toolbar. From drawing list shows a graphical summary of the items in the drawing.

The laying field is designed with the overlaps from the mesh administration relating to the mesh type and the calcu-lated required remnant meshes. The status bar shows at any time the net/gross weight for the selected mesh type and the section both for the laying and for the entire drawing.

The displayed laying can be directly taken over using Continue and completed.

Function toolbar

Longitudinal overlap, Transverse overlap Modify overlap in a longitudinal or transverse direction

Longitudinal row construction Modify the length of the starting and remnant mesh for the selected row in a longitudinal direction

Transverse row construction Modify the mesh width for the first row and the remnant mesh in a transverse direction



Variants Select user-defined laying variants

Detailed input The meshes are removed and all values, for instance the overlap in a transverse direction, mesh width, etc. are indi-vidually requested.


>> Settings for the laying variants

You can define various types of laying for 10 variants and assign clear designations to these variants.


STRAKON 57

Difference Schedule (not available in STRAKONlight) You can now compare the changes in individual mesh items between the current and a comparable drawing.


If you do not select another drawing for comparison, the current drawing will be compared with its last saved editing level.

You can hand over marked rows into the clipboard (Ctrl+C/Ctrl+V) and then, for example, insert them into Microsoft® Excel.

Modify Mesh Type in Laying Optional Adjustment of the Overlap If you change the mesh type of a laying, the relevant values for the overlap will be read from the administration and offered for modifying. The original values for the laying are also provided for selection.



AdHoc Reinforcement Insert using Comfort or Classic The inserting of AdHoc reinforcement using the menu Reinforcement > AdHoc reinforcement can now also be optionally carried out using either the Comfort input method with/without Quick Mode (see Insert using QuickBox) or Classic.

Rebar Design Mesh (not available in STRAKONlight) You can now directly save an existing crosswise rebar laying to the mesh administration as a design mesh.

Select using the menu Reinforcement > Rebar design mesh. Place a section around the rebar laying, select the direction of the longitudinal bars and assign a name to the design mesh.

The design mesh is automatically generated in the existing anchor lines and saved in the mesh administration.

Optionally you can directly delete the underlying rebar laying.

You can edit the design mesh at any time using the mesh administration, e.g. by adding dimensions for the list of design meshes.


STRAKON 59

3D Reinforcement (not available in STRAKONlight) Highly reinforced parts or intersections of reinforced parts often require a collision check between reinforcements or also in connection with 3D built-in parts. This check requires a reinforcement which is able to 3-dimensionally display the shape and position of the bar.

For this purpose the reinforcement is divided in accordance with specific criteria into 3D layers (see Basics for 3D Reinforcement).

Then select using the menu Reinforcement > 3D reinforcement or using the toolbar . All items which are capa-ble of being shown in 3D will be displayed.

Function toolbar

Item number, Diameter, Steel grade Each item number, diameter or steel grade is shown in a separate color.

Blue, Orange Display all items either in blue or orange

You can select the quality of the display in the CubeViewer using the additional function toolbar Low (quick) to High.

Basics for 3D Reinforcement You must observe the following basic rules for a correct 3-dimensional display:

3D Views The 3D views which are to be reinforced must be correctly aligned with each other, i.e. created vertically in relation to each other.

Reinforcement • A minimum of two reinforcement views must exist for each item

• At least one connection point in the reinforcement must be located within a 3D view. Reinforcements outside 3D views will be ignored.



• For the count view select the view A-/L-Plan, A-/L-Side or Point. You can use L-Leg or SmartClick on a leg if the leg length matches the dimension Plan and/or Side.

• The following counted and uncounted reinforcement views result in a 3D reinforcement:

Variant / Priority Counted View + Uncounted View = 3D reinforcement

1.1 + MV: with one or more legs without Z-leg

Laying of bending shape

1.2 + CV laying: Point *1)

1.3

CV laying: A-/L-Plan, A-/L-Side

or

CV individual: Plan, Side

+ CV laying / individually: only one point *2)

Laying of single-leg bar

2.1 + MV: single-leg

2.2

CV laying: Point

or

CV individual: Point + CV laying: A-/L-Plan,

A-/L-Side

or

CV individual: Plan, side *1)

Laying of single-leg bar

3 MV: with several legs and with Z-leg + MV: with several legs and with Bending shape Z-leg *3)

Where there are several uncounted views per item the view with the highest priority will determine the 3D display.

• Where there is one from-to item the laying of the from-to count view must be counted.

• The counted view is the most important view for the 3D creation. It contains the most data relevant to the position. For example, the laying in the left geometry has the most data relevant to the position, these being the sloped lay-ing line and the direction (angle) of the laying.

*1) In this combination the number of laid bars in the counted and uncounted count view must be identical.

*2) In the combination "counted count view laying (A-Plan/Side) + CV one point" the position of the point is sufficient for the display of all points in the 3D reinforcement.


STRAKON 61

*3) For main views with a Z-leg one counted and one uncounted main view is always required. i.e. the position in the 3D reinforcement is only defined using the main views. For the uncounted main view you can, for instance, use the function MV old.

3D Reinforcement Check (not available in STRAKONlight) You can carry out the check of the reinforcement laid in the 3D views using the menu Reinforcement > 3D rein-forcement check or the toolbar .

Here you can display individual, several or all items capable of being shown in 3D. All relevant views of the items are marked in the drawing.

Where an individual item is displayed all views will be shown in blue and the identified counted view in orange.



The views of greatest relevance for 3D creation will be marked with an arrow in the drawing:

• Arrow from the right = counted view

• Arrow from the left = associated uncounted view


Other functions are available in addition to the known functions from Item reinforcement check:

All Display all items

Accumulate Display all identified or entered items

3D views Mark all 3D views in the drawing

>> Select the quality of the display in the CubeViewer

Rotate Rotate bending shapes in the CubeViewer

If a counted count view *) is marked, the function Rotate appears in the additional function toolbar. With this you can rotate a count view which has been laid in reverse to fit correctly into the formwork.

*) This only applies for count views which have been created using the laying with L-Plan/-Side or individually with Plan/Side.


STRAKON 63

Project Steel Totals (not available in STRAKONlight) You can now select drawings from one or several working directories for the project steel totals. Optionally, you can now export the totals to Microsoft® Excel divided by steel types and/or with defined diameter groups. You determine the form of the output and selection of the templates in the new settings.

Settings The new settings are displayed when the function is carried out for the first time.

Separated steel types Output with separate steel types

Every steel type is output in a separate Excel file worksheet.

Diametergroups Output with diameter groups

Determine diameter groups Determine diameter groups for arranging the calculation of the weight

Template ... Select for output in accordance with a Microsoft® Excel template

Display settings Display settings when selecting the function Project Steel Totals, switch on/off

You can also open the dialog box for the settings using the menu Settings > Reinforcement > Project steel totals.


64 Part 10 Built-In Parts

Part 10 · Built-In Parts

General Length of the Name You can now enter a maximum of 80 characters for the file name. All permissible Windows characters are available for the naming.

Changed Function Toolbar and Additional Function Toolbar Calling up the Function The first additional function toolbar displayed after calling up the function has been expanded.


Built-in part, 3D built-in part Select built-in part type

Select between a standard built-in part, created using macro design, and a 3D built-in part, created analogous to the Flex-Parts.

Project schedule Global project schedule of the built-in parts and 3D built-in parts

3D built-in parts are marked in the project list with a $ sign in front of the name.

Drawing schedule Global drawing schedule of the built-in parts and 3D built-in parts

Delete item Delete an item from the global project list

"3D-EBT" Current master data name dependent on the selected built-in part type

Administration New file administration of the selected built-in part type (see Part 2 · Configurations, File Administration, page 16)


STRAKON 65

Mark Mark all 3D and built-in parts which have been inserted into the drawing (see Part 2 · Configurations, File Admini-stration, page 16)

Place The project and drawing lists have been moved from the additional function toolbar to the function toolbar. Function toolbar

From project list, From drawing list Select the item to be inserted with a single click:


The function toolbar when entering an item number has been expanded to include the functions From administra-tion, From project list and From drawing list.

Function toolbar

No functions relating to the administration are available at this point (see Part 2 · Configurations, File Administra-tion, page 16). The calling up of the administration in the additional function toolbar has been removed at this point.

The following additional function toolbar appears after selecting a sub image of the selected built-in part:

"w-halter.stl"“ Current name of the assignment file

If you no longer wish to have an assignment file for insertion, end the insertion, open the administration and select No File for Pen/line style:



S+Ltyp Change the pen and line style of the assignment file

Create The function toolbar and additional function toolbar are the same as for Insert.

3D Built-in Parts (not available in STRAKONlight)

General 3D built-in parts are not parameterized 3D objects whose creation is the same as for Flex-Parts.

They are administered, placed and counted like built-in parts. All items of the built-in parts and 3D built-in parts are taken into consideration for the item comparison. The list for the drawing generally contains both types of built-in part.

Calling up the Function Function toolbar

Place Place a 3D built-in part into the drawing

Create Create a 3D built-in part

The creation of a 3D built-in part is carried out using the Layers, Rotation function or directly in the CubeModeler analogous to Flex-Parts.


STRAKON 67

Modify Model a part or modify built-in part data for the list

Schedule Place a drawing-related list of both types of built-in part on the drawing


>> Settings for the built-in parts and list

Online catalog (not available in STRAKONstandard) Download of 3D built-in parts in IFC format, e.g. Halfen anchorage rail, in the DICAD portal of the CADENAS online catalog.

Register for free-of-charge access and log on with your access data.

Select a built-in part, generate the CAD MODEL (IFC file) and where necessary the PDF data sheet and load the CAD MODEL (IFC file) onto your computer.

After the download, load the file into the CubeModeler and save it as a 3D built-in part. It is now directly available for insertion.



Place Analogous to Flex-parts, the same functions (with the exception of the function Negative part) are available to you for inserting.


Create (not available in STRAKONstandard) Creating is carried out analogous to Flex-Parts. The dialog box for built-in part data opens up after modelling the part and closing the CubeModeler:

Item number The item number of the referenced 3D built-in part for inserting using a Flex-Part (see Part 6 · 3D Design, CubeViewer, Functions of the Icon Bar, page 40)

Item text Form of the item number in a drawing

%POS%: only the item number → E1 Rail %POS%: Item number with a fixed text → Rail E1

Description Text form for a built-in parts schedule

Numeric variables Numerically variable value for the description text

You can change this value when inserting. It has no influence over the size of the 3D built-in part.

Text variables Variable text for the description text

You can change this value when inserting.


STRAKON 69

Part 11 · Break Down

Wall/Ceiling General Wall Setting The setting of the function Crane from the additional function toolbar has been integrated into the dialog box for all settings.

Reinforcement with Schöck ComBAR You can automatically place Schöck ComBAR Thermo-Anchors as an alternative to a lattice girder. For this, switch on the option Insert Schöck ComBAR.

Schöck ComBAR thermo-anchors will be automatically placed into the 1st wall shell.


70 Part 11 Break Down

Wall/Ceiling Setting You can now define the attributes for the center of gravity intersection and text for the center of gravity in the element drawing.

Article numbers for the built-in parts from the article management can be optionally written into the Unitechnik file.

Example:


STRAKON 71

Wall Lattice Girder Collision Check For a visual check in the element drawing you can display the lattice girders (upper member) of the wall shell "1" as a template temporarily in the wall shell "2". You can now modify built-in parts from the layout drawing of wall shell "2" in relation to their position to the upper member or better place new built-in parts.

Using the menu Reinforcement > Lattice girders select the wall item of the existing element drawing and Collision check.

Select Place for placing the lattice girder template in the wall item. Remove this template using Delete.

Select Place all for directly inserting all lattice girder templates in all element drawings. Select Delete all to delete all lattice girder templates.

Lattice girder template in the 2nd shell:

Note: The pen weight of the lattice girders in shell "2" matches the selected pen weight for templates (see menu 2D De-sign > Template).


72 Part 11 Break Down

General Laying Settings The redesigned dialog box provides an overview of all settings for laying and the element drawing.

These new settings are now available for you:

Manage settings You can save all settings to a file (*.set) and load them once more as required.

Laying - Element Support in longitudinal direction, Support in transverse direction Separately determine the support lengths for the longitudinal and transverse directions

Element drawing - Labeling of element drawing Font, Pen, Height Settings for the title of the element drawing


STRAKON 73

Part 12 · Outputs and Interfaces

Publish / Mail Drawing (not available in STRAKONlight and STRAKONstandard)

Publish Settings: Paper Output You can now also send drawings in paper form to an output device. For this you can also select the output device in addition to entering the quantity.

Manual Unitechnik Export HPGL/PDF File of the Element Drawing When exporting data to Unitechnik you can create the element drawing as an HPGL and PDF file.

Switch on the creation of HPGL files and select the output device for the element drawing. You can choose between creating the PDF file in color or in black and white.


74 Part 12 Outputs and Interfaces

Print Direct Drawing Selection of Windows Printers in “Direct Drawing…“ If the option Select Windows printers in "Direct drawing…" is switched on (see Part 2 · Configurations, Set-tings, General Settings, Output, page 14), the Windows dialog box Print appears with the printers installed in the operating system when calling up the function Direct drawing.

You can now output the current drawing with its currently visible layers and segments directly to the printer. The set-tings of the options Drawing Border, Marginal note and Info line will be taken over from the dialog box Print Draw-ings. If you close the dialog box using Cancel, you can choose the printer for the drawing output in the list of the STRAKON output devices.

Note: • The selected Settings in the Windows dialog box, such as paper format, orientation and margins, will be noted

independently of the printer and pre-set for the next output.

• If you select the option Color for the output, the current color settings of the STRAKON printer driver cwindrv will be implemented.


STRAKON Extension Manual 2014

Documents

Transcript of STRAKON Extension Manual 2014