Stow-and-Go Router Table...Router Table Created in Alibre Design 3D Model Part 1 – Sacrificial...
Transcript of Stow-and-Go Router Table...Router Table Created in Alibre Design 3D Model Part 1 – Sacrificial...
Tabletop, 3/4 in. thick by 24 in. deep by 48 in. wide
Sacrificial fence, 3/4 in. thick by 4 in. wide by 48 in. long
Main fence, 3/4 in. thick by 3 1/2 in. wide by 48 in. long
Fence support, 3/4 in. thick by 3 1/2 in. wide by 48 in. long
Dust hood sides, 3/4 in. thick by 2 1/2 in. wide by 3 1/2 in. long
Dust hood top, 1/4 in. thick by 2 in. wide by 5 1/2 in. long
Dust hood back, 3/4 in. thick by 2 1/2 in. wide by 4 in. long; 2 1/4 in. dia. hole for hose
Opening for router plate (sized to template), 9 1/4 in. deep by 11 3/4 in. wide.;Rabbet for plate, 5/8 in. wide by 3/8 in. deep
Clamp to workbench or machine tabletop
Bolt for fence pivot, 5/16 in. dia. by 2 in.
Lower leg, 3/4 in. thick by 6 1/2 in. wide by 29 1/4 in. long
Side braces, 7/8 in. thick by 1 5/8 in. wide by 12 in. long
Front support, 7/8 in. thick by 2 1/2 in. wide by 48 in. long; Taper to 1 5/8 in. at ends
Upper leg, 3/4 in. thick by 6 1/2 in. wide by 18 in. long
Back support, 7/8 in. thick by 3 1/2 in. wide by 31 in. long; Taper to 1 5/8 in. at ends
Slot in lower leg,5/16 in. wide by 11 1/2 in. long; centered on width
Feet (milled from scrap 2x4), 1 3/4 in. thick by 3 1/2 in. wide by 6 1/2 in. long
Bolts, 5/16 in. dia. 2 in.
Stow-and-Go Router Tableby Roland Johnson
Drawings: Jim RicheyCopyright 2006, www.FineWoodworking.comCLICK HERE for companion article and video
Knobs, Threaded for 5/16 in. dia. bolts.
Rabbet, 3/4 in. wide by 3/4 in. deep, centered
Router Table
Created in Alibre Design
Part 1 – Sacrificial Fence – ¾ ” x 4” x 48”
Part 2 – Main Fence – ¾ ” x 3 ½ ” x 48”
Part 3 – Fence Support – ¾ ” x 2 ½ ” x 48”
Part 4 – Dust Hood Back – ¾ ” x 3 ½ ” x 4” 2 ¼” dia. hole
Part 5 – Dust Hood #1 – ¾ ” x 2 ½ ” x 3 ½ ”
Part 6 – Dust Hood #2 – ¾ ” x 2 ½ ” x 3 ½ ”
Part 7 – Dust Hood Top – ¼” x 2” x 5 ½ ”
Part 8 – Back Support – 7/8” 3 ½ ” x 31” Taper to 1 5/8” at ends
Part 9 – Side Brace #1 – 7/8” x 1 5/8” x 12” Explode Implode Reset
Part 10 – Upper Leg #1 – ¾ ” x 6 ½ ” x 18”
Part 11 – Lower Leg #1 – ¾ ” x 6 ½ ” x 29 ¼”
Part 12 – Lower Leg #2 – ¾ ” x 6 ½ ” x 29 ¼”
Part 13 – Upper Leg #2 – ¾ ” x 6 ½ ” x 18”
Part 14 – Side Brace #2 – 7/8” x 1 5/8” x 12”
Part 15 – Side Brace #3 – 7/8” x 1 5/8 x 12”
Part 16 – Front Support – 7/8” x 2 ½ ” x 20” Taper to 1 5/8” at ends
Part 17 – Foot #1 – 1 ¾ ” x 3 ½ ” x 6 ½ ” Milled from scrap 2x4
Part 18 – Foot #2 – 1 ¾ ” x 3 ½ ” x 6 ½ ” Milled from scrap 2x4
Part 19 – Side Brace #4 – 7/8” x 1 5/8” x 12”
Part 20 – Router Plate – 9 ¼” x 11 ¾ ”
Part 21 – Tabletop – ¾ ” x 24” x 48” Rabbet for plate – 5/8” wide by 3/8” deep