STATE A6 pro LR TUNING MANUAL - Spinaudio...Start a program of STATE A6 pro LR. 3.Select the...
Transcript of STATE A6 pro LR TUNING MANUAL - Spinaudio...Start a program of STATE A6 pro LR. 3.Select the...
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
Input method crossover
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B
Precaution for multi installation of STATE A6 pro LR
Connecting to PC-1
With Left and Right stand-alone system
USB hub
①
②②
■ USB hub x 1
■ USB cable 1. for PC / 3.5 to 4.0m long cable from the driver's seat to the STATE A6 pro (USB hub) x 1 / USB - USB cable
2. Short cables from USB hub to the STATE A6 pro x 2 (depending on the number of STATE A6 pro) /
USB - Mini USB (the hub that does not require dedicated power is recommended)
prepare depending on the number of STATE A6 pro LR
*Please make sure of the shape of the USB connector
when purchasing the cables and hubs.
■
Preparation for installation
事前に準備する物
パソコンとの接続-1
USBハブ
①
②②
■ USBハブ × 1
■ USB ケーブル ① PC用 / 運転席からBEWITHSTATE(USBハブ)までの長いケーブル (3.5~4.0m等)
STATE A6 pro の数に応じて用意する
※ ケーブル、ハブをご購入の際は、USBの形状にご注意ください 。
② USBハブから各機までの短いケーブル×2(STATE A6 proと同数必要)/USB-MiniUSB(専用電源を必要としない4ハブが推奨)
Wiring Diagram
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
CAMERA
+B +B
Analog input
Remote Eye
REMOTO out
パソコンとの接続-2
1.接続を確認し、電源を入れます。
2. STATE A6 pro LRのプログラムを起動します。
3.ConnectよりInitializeを選択します。
4. 子画面が開きます。
△△
“A6の初期化を行います。”
“A6を外して「Next」を押してください。”
5.A6のUSBケーブルを抜いて“Next”をクリックして下さい。
▲▲ ▲▲
▲接続がすべて完了したら、MM-1の接続の有無や
入力されるSIGNALの種類を選択し、Loadします。
Connecting to PC-2
1.Check the connection, and then turn.
2. Start a program of STATE A6 pro LR.
3.Select the Initialize from Connect.
4. Opens sub window.
△△
“Do the initialization of the A6.”
“After removing the A6, please press the "Next".”
5.Please click on the "Next" after unplug the A6 of the USB cable.
▲▲ ▲▲
▲Completed all connections, and presence or absence of the connection of the MM-1
Selected the type of SIGNAL to be input, and Load.
About adjustment screen
▲
▲▲
▲▲
▲
▲▲
Lch, operation screen of Rch will switch by clicking the UnitNo..
※ For a detailed operations, such as how to enter numbers, please refer to the TUNING MANUAL of STATE A6.
Adjustment of the equalizer.
Adjustment of crossover (Hipass).
Adjustment of crossover (Lowpass).
Adjustment of time alignment.
Level adjustment.
Phase switching.
Mute
▲ Unit No. and COM port in operation will be displayed here.
調整画面について
▲
▲▲
▲▲
▲
▲▲
Lch、Rchの操作画面はUnitNo.をクリックすることで切り替わります。
※ 数値の入力方法など細かな操作については、STATE A6のTUNING MANUALを参照ください。
イコライザーの調整。
クロスオーバー(Hipass)の調整。
クロスオーバー(Lowpass)の調整。
タイムアライメントの調整。
レベル調整。
位相切替え。
ミュート
▲ 操作中のUnit No.とCOMポートはココに表示されます。
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
クロスオーバーの入力方法
800Hz
800Hz
-18db/oct
-36db/oct
800Hz
-18db/oct
1000Hz
-18db/oct
50Hz
50Hz
50Hz
40Hz
-18db/oct
-18db/oct
-18db/oct
-36db/oct
STATE A6 pro LR TUNING MANUAL
パソコンとの接続-3
Lch用 Rch用
“1台目(Lch)のA6を接続してください。”
5.1台目(Lch)A6のUSBケーブルのみを接続し
“Next”をクリックして下さい。
“初期化中です”
6.2台目(Rch)A6のUSBケーブルを接続し
“Next”をクリックして下さい。
“初期化中です”
2
Lch用 Rch用
“2台目(Rch)のA6を接続してください。”
2
7.Fiinishをクリックして接続完了です。
次回以降同じパソコンで調整を行う場合は
それぞれのUSBケーブルを接続し、Refreshを
実行することで、簡単に接続完了となります。
“2初期化が完了しました。”
Connecting to PC-3
Lch Rch
“Please connect the A6 of first unit (Lch).”
5.First unit (Lch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
6.Second unit (Rch) Connect the A6
of the USB cable Please click on the "Next".
“Is initializing”
2
Lch Rch
“Please connect the A6 of second unit (Rch).”
2
7.Connection is completed by clicking the Fiinish.
If you make an adjustment in the same PC subsequent
You can connect the USB cable, it will be easy to
connect completion by clicking the Refresh.
“Initialization has ended.”
Input method equalizer
▲
▲
Click the EQ2. Second page opens.
Of 30 bands per channel Adjustment is possible.
L = R to turn on. unit1 (Lch) and unit2 (Rch) will be synchronized.
イコライザーの入力方法
▲
▲
EQ2をクリックすると2ページ目が開き、1チャンネルあたり30バンドの
調整が可能です。
L=Rをオンにすると、unit1(Lch)とunit2(Rch)が同期します。
STATE A6 pro LR TUNING MANUAL
基本配線図
Lch用 Rch用
Power Amplifier
Power Amplifier
Power Amplifier
TW_L
MW_L
SW_L
TW_R
MW_R
SW_RACC
PARKING
AV
ACC
Power Amplifier
Power Amplifier
Power Amplifier
リモコンアイ
CAMERA
+B +B