Starry Night by Vincent Van Gogh - PrusaPrinters · 2020-02-27 · Print Files (.gcode) DOWNLOAD...
4
54.91 hrs 5 pcs f 0.20 mm k 0.40 mm h 1 26.00 g d MK3/S Summary This is the next in my sequence of printing in colour. It leads on from three earlier Xmas prints. Progress has been achieved in getting a correct colour balance -the palette is limited to 220. Prints size is to a resolution of 0.35mm. I now use my Gimp script-fu to go directly from the original image to a raw data file which is the input for my program written in Scheme, This now produces sets of .obj and .gcode files. That is it converts a image into a 3d model and slices it. For this particular print I have published the .obj files but didn't use them, instead I just printed the gcodes. Please message me if your interest is piqued. Below you can see the data file image produced in Gimp. Copyright -- the original image was downloaded Wikimedia Art & Design > Wall-mounted b blunstone Starry Night by Vincent Van Gogh VIEW IN BROWSER updated 27. 2. 2020 | published 27. 2. 2020
Transcript of Starry Night by Vincent Van Gogh - PrusaPrinters · 2020-02-27 · Print Files (.gcode) DOWNLOAD...
54.91 hrs
5 pcs
f
0.20 mm
k
0.40 mm
h
1
26.00 g
d
MK3/S
Summary
This is the next in my sequence of printing in colour. It leads on from threeearlier Xmas prints.
Progress has been achieved in getting a correct colour balance -the paletteis limited to 220. Prints size is to a resolution of 0.35mm.
I now use my Gimp script-fu to go directly from the original image to a rawdata file which is the input for my program written in Scheme, This nowproduces sets of .obj and .gcode files. That is it converts a image into a 3dmodel and slices it. For this particular print I have published the .obj filesbut didn't use them, instead I just printed the gcodes. Please message meif your interest is piqued.
Below you can see the data file image produced in Gimp.
Copyright -- the original image was downloaded Wikimedia
Art & Design > Wall-mounted
b blunstone
Starry Night byVincent Van Gogh
VIEW IN BROWSER
updated 27. 2. 2020 | published 27. 2. 2020
Print Files (.gcode) DOWNLOAD ALL FILES
6.7 MB
8.00 hrs f 0.20 mm k 0.40 mm h PLA 2.00 g
updated 27. 2. 2020
4.5 MB
5.00 hrs f 0.20 mm k 0.40 mm h PLA 2.00 g
updated 27. 2. 2020
63.5 KB
0.91 hrs f 0.20 mm k 0.40 mm h PLA 11.00 g d MK3/S
updated 27. 2. 2020
17.5 MB
18.00 hrs f 0.20 mm k 0.40 mm h PLA 5.00 g
updated 27. 2. 2020
21.1 MB
23.00 hrs f 0.20 mm k 0.40 mm h PLA 6.00 g
updated 27. 2. 2020
You will need PLA in cyan, magenta, yellow and black. Print in order of filesize - smallest first, except of course the backing file (b at the end if itsname).
The gcodes do not carry print times - they will vary between 6 hours and aday.
You will see your nozzle repeatedly traversing the x-axis as it travels alongthe y axis.
Don't forget to remove the initial wipe before changing colours.
The backing file is set to a z-lift of 0.2mm and will print quickly.
Figures given for the gcodes below are estimates.
starrym.gcode
starryy.gcode
starrybg_02mm_pla_mk3s_55m.gcode
starryc.gcode
starryk.gcode
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
13.4 MBupdated 27. 2. 2020
12.3 MBupdated 27. 2. 2020
48.4 MBupdated 27. 2. 2020
93.1 MBupdated 27. 2. 2020
1.5 KBupdated 27. 2. 2020
License
This work is licensed under a Creative Commons (4.0 International License)
Attribution-NonCommercial
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition
starrym.obj
starryy.obj
starryc.obj
starryk.obj
starryb.obj
