Sheet1PENGUJIAN KABEL TEGANGAN TINGGI (XLPE)A.ROUTINE TESTNOPENGUJIANSTANDARDSYARAT PENGUJIAN1Partial DischargeIEC 60840 ,Cl 9.2 and tabel 4Test voltage1,5Uo =131 kVIEC 60885-3sensitivit level 10 pC2Voltage testIEC 60840,CL9.3Test Voltage2,5 Uo =218 kV/30 menit3Measurement of electrical resistance conductorIEC 60840,CL10,5DC value measured at 20 C max 0,021 /km4Measurement of capacitanceIEC 60840,CL10,5C0,190F/km ( 8%acc IEC)5Electric test on non-metalic inner sheathIEC 60840,Cl 9.4; IEC 60229,Cl3.1Test voltage 25 kV DC duration 1 menit6Measurement of tickness of insulationIEC 60940,Cl.10.6.2 ,tav =avv valuetavtn19,0 mm, tmin0,9 tn17,1 mn,(tmax-tmin)/tmin 0,157Measurement of tickness of metalic sheathIEC 60840,Cl.10.7.1.tav0,95 tn-0,1 ; tmin3,22 mm ; tn= 3,5,mm8Measurement of tickness of non metalic inner sheathIEC 60840,Cl. 10.6.3. tav = av valuetavto4,0 mm: tmin0,85 tn -0,1 ; tmin 3,3mm9Measurement of tickness of non metalic outer sheathIEC 60840,Cl. 10.6.3.tmin 0,85 tn-0,1 : tmin3,30 mm: tn= 4,0 mmB.SAMPLE TEST ON CABLENOPENGUJIANSTANDARTSYARAT PENGUJIAN1Hot test setIEC 60840 ,Cl 10.9 and tabel 7Max elongation under load :175%.IEC 60811-2-1,Cl.9Max permanent elong after cooling :15% 4 samples per lot2Bending testIEC 60840,CL12.3.3Diam.silinder 25(d+D)+5% 3,75 m,d =35 mm,D=108 mm3Partial dischargeIEC 60840,CL12.3.4 and table 4,IEC 60885-3Test voltage 1,5 Uo=131 kV ,sensitivity level 5 pC4Heating cycle testIEC 60840,CL12.3.6.1 heating cycle5Partial dischargeIEC 60840,CL12.3.4 and table 4,IEC 60885-3Test voltage 1,5 Uo=131 kV ,sensitivity level 5 pC6Voltage testIEC 60940,Cl.9.3. and table 4Test voltage 3 Uo =261 kV/24 jamC.ROUTINE TEST ON ACCESSORIES (on each piecce of suply)NOPENGUJIANSTANDARTSYARAT PENGUJIAN1Partial discharge test on stress cone adapter and main joint sleeveIEC 60840 ,Cl9.2.and table 4Test voltage1,5Uo =131 kV ,sensitivity level 10 pc2Voltage test on stress cone adapter and main joint sleeveIEC 60840 Cl.9.3 and table 4test voltage 2,5 Uo 218 kV /30 minSAMPLE TEST ON ACCESSORIESNOPENGUJIANSTANDARTSYARAT PENGUJIAN1Check of dimensionAccording to quality system procedur QV 750 - 2QM,Identification No;SEV 170:30603101,SM 245-S: 30805801Compliance with manufacturing drawings and parts lists2Check of packingAccording to working instruction: AA53006-01 TKG,AA 53160-01 TKG,AA 53180-01 TKGCompliance with packing list

Sheet2

Sheet3