SS/SSC 103 Multipole Plugs - Fischer Connectors · 2019-09-02 · Max.n 6 ~33 ~22 12 15 CONTACT...
2
® Max. n6 ~33 ~22 15 12 CONTACT CONFIGURATION Contacts Solder cup 103 A Z 051 2 1.18 103 A Z 052 3 1.18 103 A Z 053 4 0.79 103 A Z 054 5 0.79 Crimp (2) cup 1.18 - - 0.80 SS/SSC 103 Multipole Plugs All dimensions in mm Rev.Pages Notes : 1) All tolerances resulting from connector assembly are typically # 0.3mm 2) For optimum crimping refer to available crimping manual. 3) Max cable diameter below shield Part number example : SS 103 A062-130 600493 2 1/2 Information provided herein is believed to be accurate at time of publishing.Fischer Connectors reserves the right to make modifications on products for continuous improvement without prior notice. www.fischerconnectors.com Contact polarity A Keying codes (View from F) Contact polarity Z Contact configuration for polarity A (View from B) Contact configuration for polarity Z (View from B) Guide mark Guide mark Guide mark Code 1 (-1xx) Code 2 (-2xx) Code 3 (-3xx) 051 052 053 054 1 2 1 2 3 1 2 3 4 1 2 3 4 5 1 2 1 2 3 4 1 2 3 1 2 3 4 5 All dimensions see note 1) 10 0.8-1.0Nm 11 F B Guide mark (3) 4) This torque is a recommended value that may be influenced by the characteristics of the cable. Tests have to be made to evaluate the exact value. To secure the back nut, we recommend the use of thread locking adhesive. (4)
Transcript of SS/SSC 103 Multipole Plugs - Fischer Connectors · 2019-09-02 · Max.n 6 ~33 ~22 12 15 CONTACT...
®
Max.�n�6
~33
~22
15
12 CONTACT
CONFIGURATIONContacts
Soldercup
103AZ
051 2 1.18
103AZ
052 3 1.18
103AZ
053 4 0.79
103AZ
054 5 0.79
Crimp(2)
cup
1.18
-
-
0.80
SS/SSC 103 Multipole Plugs
All dimensions in mm Rev.Pages Notes :1) All tolerances resulting from connector assembly are typically �#� 0.3mm2) For optimum crimping refer to available crimping manual.3) Max cable diameter below shieldPart number example : SS 103 A062-130
600493 2 1/2Information provided herein is believed to be accurate at time of publishing.Fischer Connectors reserves the right to make modifications on products for continuous improvement without prior notice. www.fischerconnectors.com
Contact polarity A
Keying codes (View from F)
Contact polarity Z
Contact configuration for polarity A (View from B)
Contact configuration for polarity Z (View from B)Guide mark Guide mark Guide mark
Code 1(-1xx)
Code 2(-2xx)
Code 3(-3xx)
051 052 053 054
1
2
1
2 3
1
23
4 1
2
3 4
5
1
2
1
23
41
23
1
2
3
4
5
All dimensions see note 1)
100.8-1.0Nm11
F B
Guide mark
(3)
4) This torque is a recommended value that may be influenced by the characteristics of the cable.Tests have to be made to evaluate the exact value.To secure the back nut, we recommend the use of thread locking adhesive.
(4)
®
Max.�n�6
~33
~22
15
12 CONTACT
CONFIGURATIONContacts
Soldercup
103AZ
056 6 0.79
103AZ
057 7 0.79
103AZ
058 8 0.79
103AZ
062 12 0.43
Crimp(2)
cup
0.60
0.60
0.60
-
SS/SSC 103 Multipole Plugs
All dimensions in mm Rev.Pages Notes :1) All tolerances resulting from connector assembly are typically �#� 0.3mm2) For optimum crimping refer to available crimping manual.3) Max cable diameter below shieldPart number example : SS 103 A062-130
5) Only valid for Code 1. For other codes please contact us.
600493 2 2/2Information provided herein is believed to be accurate at time of publishing.Fischer Connectors reserves the right to make modifications on products for continuous improvement without prior notice. www.fischerconnectors.com
Contact polarity A Contact polarity Z
Contact configuration for polarity A (View from B)
Contact configuration for polarity Z (View from B)
056 057 058 062
12
3
4 5
6 1
2
3
45
6
72
1
8
7
65
4
3
10
11
45
6
78 9
2
31
12
12
3
45
6 1
2
3
45
6
72
1
8
7
65
4
3
10
11
456
78
9
2
31
12
(5) (5)
(5) (5)
Keying codes (View from F)
Guide mark Guide mark Guide mark
Code 1(-1xx)
Code 2(-2xx)
Code 3(-3xx)
All dimensions see note 1)
100.8-1.0Nm11
F B
Guide mark
(3)
4) This torque is a recommended value that may be influenced by the characteristics of the cable.Tests have to be made to evaluate the exact value.To secure the back nut, we recommend the use of thread locking adhesive.
(4)
