SRB Biodegradable 2 Stroke Oil MSDS

7/31/2019 SRB Biodegradable 2 Stroke Oil MSDS

1/7

MSDS Biomex SRB-2 Stroke Page 1 of 7

Revision Date: 12/03/2012Product No Biomex SRB-2 StrokeOil

biomex SRB-2 Stroke Oil

SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THECOMPANY/UNDERTAKING

1.1. Product identifier

Synonyms, Trade Names BIOMEX SRB- 2 Stroke Oil

1.2. Relevant identified uses of the substance or mixture and uses advised against

Identified uses: 2 Stroke oil

1.3. Details of the supplier of the safety data sheetSupplier: Biocorp Sustainables Ltd

Unit 2 Ringtail CourtBurscoughLancashireL40 8LBUnited Kingdom

Telephone : +44-(0) 7739 325341Fax : +44-(0)Emergency Telephone Number : +44-(0) 7739 325341

2. HAZARDS IDENTIFICATIONEC Classification Not classified as Dangerous under EC criteria.Human Health HazardsNo specific hazards under normal use conditions. Prolonged or repeated exposure may give riseto dermatitis. Used oil may contain harmful impurities.Safety HazardsNot classified as flammable, but will burn.Environmental HazardsNot classified as dangerous for the environment.

3.COMPOSITION / INFORMATION ON PRINCIPAL INGREDIENTSIngredient % conc. Classification CAS EINECSModified fatty acid ester


2/7


In the unlikely event of dizziness or nausea, remove casualty to fresh air. If symptoms persist,obtain medical attention.SkinRemove contaminated clothing and wash affected skin with soap and water. If persistent irritationoccurs, obtain medical attention. When using high pressure equipment, injection of product underthe skin can occur. If high pressure injuries occur, the casualty should be sent immediately to ahospital. Do not wait for symptoms to develop.EyeFlush eye with copious quantities of water. If persistent irritation occurs, obtain medical attention.IngestionWash out mouth with water and obtain medical attention. Do not induce vomiting.Advice to DoctorTreat symptomatically. Aspiration into the lungs may result in chemical pneumonitis. Dermatitismay result from prolonged or repeated exposure. High pressure injection injuries require promptsurgical intervention and possibly steroid therapy, to minimise tissue damage and loss of function.Because entry wounds are small and do not reflect the seriousness of the underlying damage,surgical exploration to determine the extent of involvement may be necessary. Local anaestheticsor hot soaks should be avoided because they can contribute to swelling, vasospasm andischaemia. Prompt surgical decompression, debridement and evacuation of foreign materialshould be performed under general anaesthetics, and wide exploration is essential.

There may be a risk to health where low viscosity products are aspirated into the lungs followingvomiting, although this is uncommon in adults. Such aspiration would cause intense local irritationand chemical pneumonitis.Children, and those in whom consciousness is impaired, will be more at risk. Emesis of lubricantsis not usually necessary, unless a large amount has been ingested, or some other compound hasbeen dissolved in the product. If this is indicated, for example, when there is rapid onset of centralnervous system depression from large ingested volume - gastric lavage under controlled hospitalconditions, with full protection of the airway is required. Supportive care may include oxygen,arterial blood gas monitoring, respiratory support, and, if aspiration has occurred, treatment withcorticosteriods and antibiotics. Seizures should be controlled with Diazepam, or appropriateequivalent drug.

5. FIRE FIGHTING MEASURES

Specific HazardsCombustion is likely to give rise to a complex mixture of airborne solid and liquid particulates andgases, including carbon monoxide and unidentified organic and inorganic compounds.Extinguishing MediaFoam and dry chemical powder. Carbon dioxide, sand or earth may be used for small fires only.Unsuitable Extinguishing MediaWater in jet. Use of halon extinguishers should be avoided for environmental reasons.Protective EquipmentProper protective equipment including breathing apparatus must be worn when approaching a firein a confined space.

6. ACCIDENTAL RELEASE MEASURESPersonal Precautions

Avoid contact with skin and eyes. Wear PVC, Neoprene or nitrile rubber gloves. Wear rubberknee length safety boots and PVC Jacket and Trousers. Wear safety glasses or full face shield ifsplashes are likely to occur.Environmental PrecautionsPrevent from spreading or entering into drains, ditches or rivers by using sand, earth, or otherappropriate barriers. Inform local authorities if this cannot be prevented.Clean-up Methods - Small SpillagesAbsorb liquid with sand or earth. Sweep up and remove to a suitable, clearly marked container fordisposal in accordance with local regulations.Clean-up Methods - Large Spillages


3/7


Prevent from spreading by making a barrier with sand, earth or other containment material.Reclaim liquid directly or in an absorbent. Dispose of as for small spills.

7. HANDLING AND STORAGEHandlingUse local exhaust ventilation if there is risk of inhalation of vapours, mists or aerosols. Avoidprolonged or repeated contact with skin. When handling product in drums, safety footwear shouldbe worn and proper handling equipment should be used. Prevent spillages. Cloth, paper andother materials that are used to absorb spills present a fire hazard. Avoid their accumulation bydisposing of them safely and immediately. In addition to any specific recommendations given forcontrols of risks to health, safety and the environment, an assessment of risks must be made tohelp determine controls appropriate to local circumstances. Exposure to this product should bereduced as low as reasonably practicable. Reference should be made to the Health and SafetyExecutive's publication 'COSHH Essentials'.

StorageKeep in a cool, dry, well-ventilated place. Use properly labelled and closeable containers. Avoiddirect sunlight, heat sources, and strong oxidizing agents. The storage of this product maybesubject to the Control of Pollution (Oil Storage) (England) Regulations. Further guidance maybeobtained from the local environmental agency office.

Storage Temperatures0C Minimum. 50C Maximum.Recommended MaterialsFor containers or container linings, use mild steel or high density polyethylene.Unsuitable MaterialsFor containers or container linings, avoid PVC.Other InformationPolyethylene containers should not be exposed to high temperatures because of possible risk ofdistortion.

8. EXPOSURE CONTROLS, PERSONAL PROTECTIONExposure LimitsSubstance Regulations Exposure Duration Exposure Limit Units

Oil mist, mineral EH 40 2005 TWA 5 mg/m3EH 40 2005 STEL 10 mg/m3

EH 40 2005 EH 40 2005 Health and Safety Executive. EH40; Workplace Exposure LimitsExposure ControlsThe use of personal protective equipment is only one aspect of an integrated approach to theControl Of Substances Hazardous to Health.The management of Health and Safety at Work Regulations 1992 require employers to identifyand evaluate the risks to health and to implement appropriate measures to eliminate or minimisethose risks. The choice of personal protective equipment is highly dependent upon localconditions, e.g. exposure to other chemical substances and micro-organisms, thermal hazards(protection from extremes of cold and heat), electrical hazards, mechanical hazards andappropriate degree of manual dexterity required to undertake an activity.Whilst the content of this section may inform the choice of personal protective equipment used,

the limitations of any information which can be provided must be fully understood, e.g. personalprotective equipment chosen to protect employees from occasional splashes maybe entirelyinadequate for activities involving partial or complete immersion.If the levels of oil mist or vapourin air are likely to exceed the occupational exposure standards then consideration should begiven to the use of local exhaust ventilation to reduce personal exposure.The choice of personal protective equipment should only be undertaken in the light of a full riskassessment by a suitably qualified competent person ( e.g. a professionally qualified occupationalhygienist). Effective protection is only achieved by correctly fitting and well maintained equipmentand employers should ensure that appropriate training is given. All personal protective equipmentshould be regularly inspected and replaced if defective. Reference should be made to HSE's


4/7


publication Methods for the Determination of Hazardous Substances (MDHS) 84 - Measurementof oil mist from mineral oil-based metalworking fluids. Measurement of an employee's exposure tooil vapour maybe supplemented through the use of stain tubes. In the first instance, furtherguidance maybe obtained through HSE's publication 'COSHH - a brief guide to the regulations'(INDG 136(rev1)).Respiratory ProtectionAt standard temperature and pressure, the Occupational Exposure Standard for oil vapour isunlikely to be exceeded. Care should be taken to keep exposures below applicable occupationalexposure limits. If this cannot be achieved, use of a respirator fitted with an organic vapourcartridge combined with a particulate pre-filter should be considered. Half masks (EN 149) orvalved half masks (EN 405) in combination with type A2 (EN 141) and P2/3 (EN 143) pre-filtersmaybe considered.Hand ProtectionChemical protective gloves are made from a wide range of materials, but there is no single glovematerial ( or combination of materials) which gives unlimited resistance to any individual orcombination of substances or preparations. The extent of the breakthrough time will be affectedby a combination of factors which include permeation, penetration, degradation, use pattern ( fullimmersion, occasional contacts) and how the glove is stored when not in use.Theoretical maximum levels of protection are seldom achieved in practice and the actual level ofprotection can be difficult to assess. Effective breakthrough time should be used with care and a

margin of safety should be applied. HSE guidance on protective gloves recommends a 75%safety factor to be applied to any figures obtained in a laboratory test. Nitrile gloves may offerrelatively long breakthrough times and slow permeation rates. Test data, e.g breakthrough dataobtained through test standard EN374-3:1994 are available from reputable equipment suppliers.Personal hygiene is a key element of effective hand care. Gloves must only be worn on cleanhands. After using gloves, hands should be washed and dried thoroughly. A non perfumedmoisturiser should be applied.Eye ProtectionGoggles conforming to a minimum standard of EN 166 345B should be considered if there is apossibility of eye contact with the product through splashing. Higher rated eye protection must beconsidered for highly hazardous operations or work areas. For example, employees involved inmetalworking operations such as chipping, grinding or cutting may require additional protection toavert injury from fast moving particles or broken tools.

Body ProtectionMinimise all forms of skin contact. Overalls and shoes with oil resistant soles should be worn.Launder overalls and undergarments regularly.Environmental Exposure ControlsMinimise release to the environment. An environmental assessment must be made to ensurecompliance with local environmental legislation.

9 PHYSICAL AND CHEMICAL PROPERTIESAppearance: Clear liquidOdour: PerceptibleAcidity/Alkalinity not applicableInitial boiling point n/a

Pour Point -9CFlash Point >150C

Vapour pressure @20C


5/7


StabilityStable.Conditions to AvoidExtremes of temperature and direct sunlight.Materials to AvoidStrong oxidizing agents.Hazardous Decomposition ProductsHazardous decomposition products are not expected to form during normal storage.

11. TOXICOLOGICAL INFORMATIONBasis for AssessmentToxicological data have not been determined specifically for this product. Information given isbased on a knowledge of the components and the toxicology of similar products.Acute Toxicity - OralLD50 expected to be > 2000 mg/kg.Acute Toxicity - DermalLD50 expected to be > 2000 mg/kg.Acute Toxicity - InhalationNot considered to be an inhalation hazard under normal conditions of use.Eye Irritation

Expected to be slightly irritating.Skin IrritationExpected to be slightly irritating.Respiratory IrritationIf mists are inhaled, slight irritation of the respiratory tract may occur.Skin SensitisationNot expected to be a skin sensitizer.CarcinogenicityComponents are not known to be associated with carcinogenic effects.MutagenicityNot considered to be a mutagenic hazard.Reproductive ToxicityNot considered to be toxic to reproduction.

Other InformationProlonged and/or repeated contact with products containing mineral oils may result in defatting ofthe skin, particularly at elevated temperatures. This may lead to irritation and possibly dermatitis,especially under conditions of poor personal hygiene. Skin contact should be minimised. Highpressure injection of product into the skin may lead to local necrosis if the product is not surgicallyremoved. Used oils may contain harmful impurities that have accumulated during use. Theconcentration of such impurities will depend on use and they may present risks to health and theenvironment on disposal. ALL used oil should be handled with cautionand skin contact avoided as far as possible.

12. ECOLOGICAL INFORMATIONBasis for AssessmentEcotoxicological data have not been determined specifically for this product. Information given is

based on a knowledge of the components and the ecotoxicology of similar products.MobilityLiquid under most environmental conditions. Floats on water. If it enters soil, it will adsorb to soilparticles and will not be mobile.Persistence / DegradabilityNot expected to be readily biodegradable. Major constituents are expected to be inherentlybiodegradable, but the product contains components that may persist in the environment.BioaccumulationContains components with the potential to bioaccumulate.Ecotoxicity


6/7


Poorly soluble mixture. May cause physical fouling of aquatic organisms. Product is expected tobe practically non-toxic to aquatic organisms, LL/EL50 >100 mg/l. (LL/EL50 expressed as thenominal amount of product required to prepare aqueous test extract). Mineral oil is not expectedto cause any chronic effects to aquatic organisms at concentrations less than 1 mg/l.Other Adverse EffectsNot expected to have ozone depletion potential, photochemical ozone creation potential or globalwarming potential. Product is a mixture of non-volatile components, which are not expected to bereleased to air in any significant quantities.

13. DISPOSAL CONSIDERATIONSWaste DisposalRecycle or dispose of in accordance with prevailing regulations, by a recognised collector orcontractor. The competence of the contractor to deal satisfactorily with this type of product shouldbe established beforehand. Do not pollute the soil, water or environment with the waste product.Product DisposalAs for waste disposal.Container DisposalRecycle or dispose of in accordance with the legislation in force with a recognised collector orcontractor.

14. TRANSPORT INFORMATIONTransport InformationNot dangerous for transport under ADR/RID, IMO and IATA/ICAO regulations.ADR/RID ClassNone AllocatedADR/RID Packing GroupNone AllocatedIMDG Hazard ClassNone AllocatedIMDG Packing GroupNone AllocatedIATA Hazard Class

None AllocatedIATA Packing GroupNone Allocated

15. REGULATORY INFORMATIONEC Symbols None.EC Risk Phrase Not classified.EC Safety Phrase Not classified.EINECS All components listed or polymer exempt.TSCA (USA) All components listed.National LegislationEnvironmental Protection Act 1990 (as amended).Health and Safety at Work Act 1974

Consumers Protection Act 1987Control of Pollution Act 1974Environmental Act 1995Factories Act 1961Shell HVI 650Version No. 1.3 12/05/2008 Page 7 of 9Carriage of Dangerous Goods by Road and Rail (Classification, Packaging and Labelling)RegulationsChemicals (Hazard Information and Packaging for Supply) Regulations 2002.Control of Substances Hazardous to Health Regulations 1994 (as amended).


7/7


Road Traffic (Carriage of Dangerous Substances in Packages) RegulationsMerchant Shipping (Dangerous Goods and Marine Pollutants) RegulationsRoad Traffic (Carriage of Dangerous Substances in Road Tankers in Tank Containers)RegulationsRoad Traffic (Training of Drivers of Vehicles Carrying Dangerous Goods) RegulationsReporting of Injuries, Diseases and Dangerous Occurences RegulationsHealth and Safety (First Aid) Regulations 1981Personal Protective Equipment (EC Directive) Regulations 1992Personal Protective Equipment at Work Regulations 1992Packaging & LabellingSafety data sheet available for professional user on request.

16. OTHER INFORMATIONRevisions HighlightedRevised according to REACH Legislation

Further InformationThis information is based on our current knowledge and is intended to describe the product forthe purposes of health, safety and environmental requirements only. It does not constitute aguarantee for any specific property of the product.

SRB Biodegradable 2 Stroke Oil MSDS

Documents

Transcript of SRB Biodegradable 2 Stroke Oil MSDS