Spreader Training - EH5U & EH170U
-
Upload
david-adeola-ogunyemi -
Category
Documents
-
view
704 -
download
82
Transcript of Spreader Training - EH5U & EH170U
![Page 1: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/1.jpg)
SPREADER TRAINING MODULE
![Page 2: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/2.jpg)
CONTENTS OF MODULE
1. Introduction to Spreaders
2. Technical Data
3. Spreader Overview
4. Structural Sections
5. Functional Mechanisms
6. Hydraulic System
7. Electrical system
8. Spreader Interlocks
![Page 3: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/3.jpg)
Spreaders are the most intensively used lifting equipments and has been designed to lift Standard ISO Containers – Length 20-ft (6.1 m), 40-ft (12.2 m), 45-ft (13.7 m) and Width 8-ft (2.4 m).
Data reveals that Spreader breakdowns accounts to nearly 60 – 70% of total breakdowns in cranes. Spreaders are continuously subjected to shocks & vibrations when it comes in contact with containers, so understanding the functioning of all mechanisms and proper maintenance is the key to smooth Spreader operation.
INTRODUCTION TO SPREADERS
![Page 4: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/4.jpg)
TECHNICAL DATA
Spreader Model – EH5U(Single Lift) & EH170U(Twin Lift)
Dead Load – 9 Tonnes (EH5U) & 10.7 Tonnes (EH170U)
Lifting CapacitySingle Lift – 41 TonnesTwin Lift – 2 x 25 Tonnes
Lifting Lugs – 4 x 10 Tonnes in Main & End Beam
Telescopic Position –20ft position – 5852 mm ± 3 mm30ft position – 8918 mm ± 3 mm40ft position – 11984 mm ± 3 mmTwistlock Pins center at End Frame – 2259 mm
![Page 5: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/5.jpg)
TECHNICAL DATA
Gravity Point Adjustment – ± 1200 mm in 20 Secs
Operations –
20 Ft to 40 Ft – 30 Secs
Twistlock Rotation (90°) – 1.5 Secs
Flipper Up / Down (180°) – 3 to 5 Secs
Hydraulics –
Pump – Axial Piston Pump
Pump Running Pressure – 100 bar
Cross Line Relief Valve (Flipper) – 140 bar
Pump Flow (Flipper & Twistlock) – 14 Ltrs / min
Pump Flow (Twin up/down) – 18 Ltrs / min
Tank Capacity (Flipper & Twistlock) – 50 Ltrs (2 Nos)
Tank Capacity (Twin up/down) – 70 Ltrs (1 No)
Pressure Line Filter – 10 Microns
![Page 6: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/6.jpg)
TECHNICAL DATA
Electrical – Power Voltage - 400 VAC / 50 Hz / 3PHControl Voltage - 230 VACControl Valve (Solenoid Coil) - 24 VDCLights - 24 VDCPump Motor (Flipper & Twistlock) - 2.2 KW ( 2 Nos.)Pump Motor (Twin Up/Down) - 3 KW ( 1 No.)Motor (Telescopic) - 3 KW ( 1 No.)Motor (Gravity Adjustment) - 3 KW ( 1 No.)Electrical Protection - IP 55
![Page 7: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/7.jpg)
Structural Sections:
Center body
Telescopic Arm
Tower
SPREADER OVERVIEW
Functional Mechanisms: Telescopic DriveFlipper Up / DownTower Gravity Point AdjustmentTwinlift Housing Up/ Down Twistlock and Land Pin
Control System:Electrical Hydraulic
![Page 8: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/8.jpg)
STRUCTURAL DESCRIPTION
Bromma Telescopic Spreader is fabricated as all welded, high quality steel, construction. Two pairs of telescopic beams slide in the centre main frame construction. The telescopic beams are joined together at the ends by end beams, which house the twistlocks, flipper arms and hydraulic valves. The spreader has an inbuilt under clearance of 185 mm. The spreader is optionally fitted with one set of lifting lugs.
![Page 9: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/9.jpg)
FUNCTIONAL MECHANISMS
TELESCOPIC SYSTEMThe telescoping system is driven by means of an electric motor and reduction gearbox connected to an endless chain. This chain is fitted with stacks of spring washers that work as shock absorbers where the chain attaches to the tension rods. These tension rods are connected to the end beam. The springs allow for changes in the length of the spreader up to plus or minus 7 mm. The springs do not only act as shock absorbers, they also provide a floating possibility for the twistlocks to handle distorted containers. In the event of a power failure the telescoping motion can be hand cranked. The positioning system works with proximity switches
for positioning the spreader in the 20', 30' and 40' positions. The drive motor incorporates an electric brake that is spring applied and takes electrical power to release. This brake not only controls the accuracy in stopping the expansion and retraction but also prevents changes from occurring in the spreader length during use.
![Page 10: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/10.jpg)
20–40 MECHANISM
![Page 11: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/11.jpg)
20–40 MECHANISM
![Page 12: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/12.jpg)
FUNCTIONAL MECHANISMS
TOWER & GRAVITY POINT ADJUSTMENTThe main frame of the spreader is connected to the crane through a sliding tower assembly. This enables the centre of gravity lifting point to be moved a maximum of 1,2 meters toward each end of the spreader. After unlocking an unevenly loaded container, the sliding tower assembly automatically returns to the central position.
![Page 13: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/13.jpg)
TOWER CHAIN ASSEMBLY
![Page 14: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/14.jpg)
TOWER CHAIN ASSEMBLY
![Page 15: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/15.jpg)
FUNCTIONAL MECHANISMS
FLIPPER MECHANISMFlat gather guides, commonly called flippers, are fitted to each end beam of the spreader. They are of strong construction and are driven by a powerful hydraulic motor, which enables easy and fast location of the spreader onto the containers. The flipper gather is 155 mm and has a gathering torque of 1200 Nm. The flipper arms are always under pressure and each arm is controlled by its own solenoid valve and shock relief valve, which opens at a pre-set pressure of 45 bar above the normal working pressure. As soon as the shock load ends the flipper returns to the vertical position.The speed of the flipper is approximately 180° in 6 seconds and is controlled by an orifice plug in the pipe connection to the motor.
![Page 16: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/16.jpg)
FLIPPER ASSEMBLY
![Page 17: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/17.jpg)
FLIPPER ASSEMBLY
![Page 18: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/18.jpg)
FUNCTIONAL MECHANISMS
TWISTLOCK ASSEMBLYFour twistlocks for single container spreader are located in the corners of the spreader to engage and lift the container. A hydraulic cylinder rotates the twistlock and two sensors indicate the position of the twistlock, Locked or Unlocked. A spring loaded landing pin near each twistlock is pushed up into the twistlock housing when the spreader is landed on the container. When the spreader is properly landed on a container, the landing pin will activate a proximity switch. Only when all the corners of the spreader are landed, can the twistlocks be turned. At the same time, the blockading key is moved high enough so the blockading stop on the twistlock lever arm passes underneath it. If the spreader is not
properly landed the proximity switch will not be activated and the blockading key will get in the way of the blocking stop. This will stop the twistlocks from turning.
![Page 19: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/19.jpg)
TWISTLOCK ASSEMBLY
![Page 20: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/20.jpg)
FUNCTIONAL MECHANISMS
CENTER TWISTLOCKSThe EH 170 is equipped with center twistlocks to be able to handle two 20 foot containers at the same time. These center twistlocks are placed in housings on the main frame. The twistlock boxes can be tilted to “down” position by four hydraulic cylinders. (one per twistlock box). The center twistlocks operate the same way as the end beam twistlocks.
![Page 21: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/21.jpg)
HYDRAULIC CONTROL SYSTEM
The hydraulic units are protected inside each end beam. The unit consists of a built-in tank, variable displacement piston pump, motor valves and filter. The filter cap is fitted with a pressure relief valve plus or minus 0,14 bar to allow expansion and contraction of air inside the tank. The hydraulic components used are designed to work at over 200 bar but normal working pressure is 100 bar. The hydraulic valves are solenoid operated and can be tested by hand operating.The EH170U has a third hydraulic unit placed in the main beam. This unit provides the four cylinders for center twistlock housings up-down and the four cylinders for lock-unlock in the central twistlocks with power.
![Page 22: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/22.jpg)
FLIPPER & CORNER TWISTLOCK HYDYAULIC SETUP
![Page 23: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/23.jpg)
FLIPPER & CORNER TWISTLOCK HYDYAULIC CIRCUIT
![Page 24: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/24.jpg)
P T
A B
M
Sol B Active
M
140 Bar
140 Bar
Flipper Down
FLIPPER DOWN HYDYAULIC CIRCUIT
Down
Pump Pressure - 100 Bar
![Page 25: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/25.jpg)
P T
A B
M
Sol A Active
M
140 Bar
140 Bar
Flipper Up
FLIPPER UP HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 26: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/26.jpg)
P T
A B
M
Sol A Active
Twistlock Lock
CORNER TWISTLOCK LOCK HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 27: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/27.jpg)
P T
A B
M
Sol B Active
Twistlock UnLock
CORNER TWISTLOCK UNLOCK HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 28: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/28.jpg)
TWIN PICK HYDYAULIC CIRCUIT
![Page 29: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/29.jpg)
P T
A B
M
210 Bar
TWIN PICK HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 30: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/30.jpg)
P T
A B
M
210 Bar
Sol B Active
TWIN DOWN HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 31: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/31.jpg)
P T
A B
M
210 Bar
Sol A Active
TWIN UP HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 32: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/32.jpg)
P T
A B
M
210 Bar
Sol A Active
Twistlock Unlock
TWISTLOCK UNLOCK HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 33: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/33.jpg)
P T
A B
M
210 Bar
Sol B Active
Twistlock Lock
TWISTLOCK LOCK HYDYAULIC CIRCUIT
Pump Pressure - 100 Bar
![Page 34: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/34.jpg)
TWISTLOCK MAINTENANCE
![Page 35: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/35.jpg)
TWISTLOCK FLOAT CHECK
![Page 36: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/36.jpg)
ADJUSTING SPREADER LENGTH
![Page 37: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/37.jpg)
ADJUSTING TELESCOPIC CHAIN
![Page 38: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/38.jpg)
TOWER MOTOR BRAKE CHECK
![Page 39: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/39.jpg)
MAINTENANCE PROCEDURES
A. Find below the list of Lubricating Points & their respective positions
![Page 40: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/40.jpg)
MAINTENANCE PROCEDURES
![Page 41: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/41.jpg)
MAINTENANCE PROCEDURES
B. Check Points in Spreader
1. Inspect and verify condition of 20’-40’ motor & gearbox assembly
2. Check motor brake condition & air gap (0.25 mm to 0.6 mm)
3. Check telescopic gear box oil level, oil condition, leakages
4. Check telescopic drive sprocket condition, Roller chain condition & Tension wheel condition. Grease, if necessary.
5. Check chain slackness ( 25 mm in vertical direction). Adjust, if necessary
6. Check roller chain end lock nuts tightness (45 Nm) & shock absorber (Disc spring) condition. Replace if found broken/cracked
7. Check all Robalon glide plates condition. Replace when thickness goes less than 17 mm.
8. Grease the sliding area under the telescopic beams with brush
9. Inspect and verify for Center distance of twist locks
10. Inspect and verify condition of Tower shifting motor & Gearbox assembly
![Page 42: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/42.jpg)
MAINTENANCE PROCEDURES
11. Check tower motor brake torque (75 Nm)
12. Check Tower shifting gear box oil level, oil condition, leakages
13. Check tower drive sprocket condition, Idler sprockets condition & Roller chain condition. Grease, if necessary.
14. Check chain slackness and adjust, if necessary
15. Check gearbox alignment / chain tensioning bolts are touching gearbox base
16. Check Tower shifting Robalon glide plate condition & thickness
17. Check tightness of all bolts / fasteners
18. Check oil level in both Hydraulic tanks and fill slightly below max. Mark
19. Check hydraulic oil condition
20. Check whether filter clog indicator has changed from green to red if so, change filter element
21. Inspect and verify condition of Hydraulic Tank, Valve Assembly, hose condition. Check for any leakages
![Page 43: Spreader Training - EH5U & EH170U](https://reader033.fdocuments.in/reader033/viewer/2022061109/5450d52ab1af9fc8038b4a33/html5/thumbnails/43.jpg)
MAINTENANCE PRODEDURES
22. Check Hydraulic pump pressure (100 Bar)
23. Check twistlock nut & floating mechanism.
24. Ensure all the parts are properly tightened.
25. Check twistlock cylinder & all hose fittings for any leakage
26. Check landpin condition & lubricate with oil
27. Dismantle all twistlocks every six months & check for cracks by doing dye-penetration test. Clean & inspect all parts. Replace, if necessary.
28. Check all flipper condition & Hub fasteners tightness
29. Check flipper motor for proper operation & hose fitting leakages
30. Check Twin pick motor & pump assembly condition
31. Check twin up/down cylinder mountings & also check for any leakages
32. Check all Buffer condition & mounting bolts for proper tightness
33. Check all structures for damage, welding cracks & deformation.
34. Check all operations of Spreader