SPECIFICATIONS...With our unique IDD (Isolated Direct Drive) Spindle Design and our ultra-wide,...
Transcript of SPECIFICATIONS...With our unique IDD (Isolated Direct Drive) Spindle Design and our ultra-wide,...
FV56T FV56A FV85A FV102A FV125ASPINDLESpindle Speed (opt.) 15,000rpm 10,000rpm (12,000/15,000rpm )
Spindle Power (opt.) 2.2/3.7kW 3/5HP (cont./15min.)5.5/7.5/11/15kW
7/10/15/20HP (cont./30min./10min./5min.)
5.5/7.5/11/15kW 7/10/15/20HP (7.5/11/15/22kW 10/15/20/30HP)(cont./30min./10min./5min.)
Spindle Taper BT30 BBT40Front Bearing Diameter ø45mm ø1.77" ø70mm ø2.76"TRAVEL X-axis Travel 560mm 22.05" 850mm 33.46" 1,020mm 40.16" 1,270mm 50"Y-axis Travel 410mm 16.14" 520mm 20.47"Z-axis Travel 450mm 17.72" 540mm 21.26" Distance Between Spindle Nose & Table Top 110~560mm 4.33"~22.05" 150~690mm 5.91"~27.17" 105~645mm 4.13"~25.39"
TABLETable size 700 x 420mm 27.56"~16.54" 1,000 x 520mm
39.37" x 20.47" 1,120 x 520mm44.09" x 20.47"
1,350 x 520mm53.15" x 20.47"
T-Slots × Size × Pitch 3 x 14mm x 100mm 3 x 0.55" x 3.94" 5 x 18mm x 100mm 5 x 0.71" x 3.94" Max. Load on Table 300kg 661 lb 500kg 1,102 lb 1,000kg 2,205 lbFEEDRATERapid Feedrate 36/36/24 m/min. (48/48/48 m/min.)
1,417/1,417/945ipm (1,890/1,890/1,890ipm) 36/36/24 m/min. 1,417/1,417/945ipm 24/24/24 m/min. 945/945/945ipm
Cutting Feedrate 1~10,000mm/min. (0.04~394ipm) ATCTool Magazine Capacity 16T (20T) 20T 24T (30T)Max. Tool Weight (per piece) 4kg 8.8 lb 6kg 13.2 lbPull Stud MAS-P30T-1 MAS-P40T-1
Max. Tool Dimensions ø63 x 200mm ø2.48" x 7.87"
ø90mm x 250mmø3.54" x 9.84"
ø90mm x 300mm (ø76mm x 300mm) ø3.54" x 11.81" (ø2.99" x 11.81")
Max.Tool Dimensions (Without adjacent tools) ø100mm ø3.94" ø125mm ø4.92"
Tool Changer Method Arm Type Arm Type (Armless Type)Tool Selection Method Random Random (By Sequence)GENERALPneumatic Supplier 5.5kg/cm2 78.2psl Power Consumption (std.) 16kVA (17kVA) 25kVA (30kVA)Machine Weight 2,800kg 6,173 lb 3,000kg 6,614 lb 5,260kg 11,596 lb 5,350kg 11,795 lb 6,700kg 14,771 lb
Tool Kit ● ● ● ● ●Work Lamp ● ● ● ● ●Pilot Lamp ● ● ● ● ●Coolant Gun ● ● ● ● ●Coolant Equipment System ● ● ● ● ●Cuttng Air Blast ● ● ● ● ●Spindle Air Blast ● ● ● ● ●Spindle Air Seal ● ● ● ● ●Central Lubrication System ● ● ● ● ●Oil Skimmer ● ● ● ● ●Coolant Through Spindle System - ○ ○ ○ ○Foundation Bolts ○ ○ ○ ○ ○Leveling Blocks and Bolts ● ● ● ● ●Oil-Mist Coolant System ○ ○ ○ ○ ○Oil Hole Holder Function - ○ ○ ○ ○Chips Flush Coolant System ○ ○ ○ ○ ○Chip Conveyor ○ ○ ○ ○ ○Workpiece Measurement System ○ ○ ○ ○ ○Heat Exchanger for Electrical Cabinet ● ● ● ● ●A/C. Cooler for Electrical Cabinet ○ ○ ○ ○ ○
Mechanical, Electrical & Operating Manuals ● ● ● ● ●
Rigid Tapping ● ● ● ● ●Guideway Cover (X,Y,Z) ● ● ● ● ●Optical Scale ○ ○ ○ ○ ○Automatic Door ○ ○ ○ ○ ○Safty Door ● ● ● ● ●4th Axis Rotary Table ○ ○ ○ ○ ○Spindle Cooling System ○ ○ ○ ○ ○Heavy Duty Coolant Pump ○ ○ ○ ○ ○Auto Tool Length Measurement System ○ ○ ○ ○ ○
Full Chip Enclosure ● ● ● ● ●Circular Coolant Nozzle ○ ○ ○ ○ ○Screw Type Chip Conveyor - - ● ● -Air Gun ● ● ● ● ●Automatic Power Off Device ○ ○ ○ ○ ○Hydraulic System ○ ○ ○ ○ ○Oil-Mist Collector ○ ○ ○ ○ ○CNC Controller: MXP-200FB ● ● ● ● ●CNC Controller: MXP-200FC ○ ○ ○ ○ ○
SPECIFICATIONS
ACCESSORIES
PULL STUD TOOL SHANKNote: The manufacturer reserves the right to modify the design, specifications, mechanisms, etc. to improve the performance of the machine without notice. All the specifications shown above are just for reference.
0.31”
ø0.4
9”
ø31.
8 ø1
.25”
ø46
ø1.8
1”
ø38
ø1.5
”
16 0
.63”
48.4 1.91”70.4 2.77”
2 0.08”22 0.87”
43 1.69”23 0.91” 4
0.16”3 0.12”
M12 x 1.75P
M12 x 1.75P
Taper 7/24
5 0.2”3.5 0.14”
2.5 0.1”
ø11 ø
0.43”
ø7
ø0.28
”
ø16.5
ø0.6
5”
ø9.5
ø0.37
”ø1
2.5 ø
0.49”
18 0.71”
65.42.57”
16.60.65”
Taper 7/24
M16
x 2
P
ø10 ø0.39”
ø44.
45 ø
1.75
”
1-0.005 250.98”
ø53
ø2.0
9”
ø75.
7 ø2
.98”
ø63
ø2.4
8”
30°
ø15
ø0.5
9”
28 1.10”30.13”
35 1.38” 40.16”
60 2.36”
ø17
ø0.6
7”
M16
x 2
P
ø10
ø0.
39” ø2
3ø0
.90”
45°
Ball Diameter
50.19”
BT30 MAS-P30T-1 BBT40 MAS-P40T-1
HBM
FP FP55LX, FP66A, FP100A / FP66G
FV FV56T, FV56A, FV85A, FV102A, FV125A / FV50T
XV XV560A, XV1020A, XV1250A
MV MV66A, MV76A, MV86A, MV106A
FX FX380A
NSV NSV66A, NSV85A, NSV102A, NSV156A
NDV NDV66A, NDV85A, NDV102A
NBX NBX102A
TCV TCV2000A, TCV3000A, TCV3000A-5AF, TCV3000A-5AX
NTV NTV158A/B
DCV
TV TV116B, TV146A/B, TV158B, TV188B, TV2110B, TV2610B
NXV1020A, NXV1020AM
WV WV108A/B
High Efficiency T-base Vertical Machining Center
High Precision Die & Mold Vertical Machining Center
/ High Precision Graphite Vertical Machining Center
High Performance
High Performance Swivel Head 5-axis Vertical Machining Center
High Performance Double Column Vertical Machining Center
NXV
DCV2012A/B, DCV2016B, DCV3016B, DCV4016B, DCV3021B, DCV4021B, DCV5021B, DCV6021B, DCV3025B, DCV4025B, DCV5025B, DCV4035B, DCV5035B, DCV6035B, DCV4030B, DCV5030B, DCV6030B, DCV4030B-5AF, DCV5030B-5AX, DCV6030B-5AX, DCV4030B-5AF
NDC NDC2016B, NDC3016B, NDC3016B
H H500A/B, H630B, H800B, H2612B
NH NH450A, NH630B, NH800B
High Speed High Precision Horizontal Machining Center
GT GT-200A/B/MA, GT-250A/B/MA/MB, GT-300A/B/LA/LB/MA/MB/LMA/LMB, GT-380A/B/LA/LB
TC TC-16A/B/LA/LB/MA/MB/LMA/LMB, TC-26, TC-26L, TC-36, TC-36W, TC-46, TC-46M
BMP BMP1416B
NT NT-2000Y/SY, NT-2500Y/SY
High Performance Mill-axis Mill/Turn Center
High Accuracy Heavy Duty Boring Machine
Horizontal Boring Milling Machining Center
A remote monitoring systemRemote Monitoring System
YEONG CHIN MACHINERY INDUSTRIES CO., LTD.888 Homu Road, Shengang District, Taichung, Taiwan
022013-E09-1000
FV56T FV56A FV85A FV102A FV125ASPINDLESpindle Speed (opt.) 15,000rpm 10,000rpm (12,000/15,000rpm )
Spindle Power (opt.) 2.2/3.7kW 3/5HP (cont./15min.)5.5/7.5/11/15kW
7/10/15/20HP (cont./30min./10min./5min.)
5.5/7.5/11/15kW 7/10/15/20HP (7.5/11/15/22kW 10/15/20/30HP)(cont./30min./10min./5min.)
Spindle Taper BT30 BBT40Front Bearing Diameter ø45mm ø1.77" ø70mm ø2.76"TRAVEL X-axis Travel 560mm 22.05" 850mm 33.46" 1,020mm 40.16" 1,270mm 50"Y-axis Travel 410mm 16.14" 520mm 20.47"Z-axis Travel 450mm 17.72" 540mm 21.26" Distance Between Spindle Nose & Table Top 110~560mm 4.33"~22.05" 150~690mm 5.91"~27.17" 105~645mm 4.13"~25.39"
TABLETable size 700 x 420mm 27.56"~16.54" 1,000 x 520mm
39.37" x 20.47" 1,120 x 520mm44.09" x 20.47"
1,350 x 520mm53.15" x 20.47"
T-Slots × Size × Pitch 3 x 14mm x 100mm 3 x 0.55" x 3.94" 5 x 18mm x 100mm 5 x 0.71" x 3.94" Max. Load on Table 300kg 661 lb 500kg 1,102 lb 1,000kg 2,205 lbFEEDRATERapid Feedrate 36/36/24 m/min. (48/48/48 m/min.)
1,417/1,417/945ipm (1,890/1,890/1,890ipm) 36/36/24 m/min. 1,417/1,417/945ipm 24/24/24 m/min. 945/945/945ipm
Cutting Feedrate 1~10,000mm/min. (0.04~394ipm) ATCTool Magazine Capacity 16T (20T) 20T 24T (30T)Max. Tool Weight (per piece) 4kg 8.8 lb 6kg 13.2 lbPull Stud MAS-P30T-1 MAS-P40T-1
Max. Tool Dimensions ø63 x 200mm ø2.48" x 7.87"
ø90mm x 250mmø3.54" x 9.84"
ø90mm x 300mm (ø76mm x 300mm) ø3.54" x 11.81" (ø2.99" x 11.81")
Max.Tool Dimensions (Without adjacent tools) ø100mm ø3.94" ø125mm ø4.92"
Tool Changer Method Arm Type Arm Type (Armless Type)Tool Selection Method Random Random (By Sequence)GENERALPneumatic Supplier 5.5kg/cm2 78.2psl Power Consumption (std.) 16kVA (17kVA) 25kVA (30kVA)Machine Weight 2,800kg 6,173 lb 3,000kg 6,614 lb 5,260kg 11,596 lb 5,350kg 11,795 lb 6,700kg 14,771 lb
High Speed High Performance Machining Vertical Center
HIGH SPEED HIGH PERFORMANCE MACHINING VERTICAL CENTER
The YEONG CHIN FV-Series High-Speed, High-Power Vertical Machining Centers are specially designed for industries that demand high precision, high productivity application such as automotive, aerospace, electronic, and job shop industries.
With our unique IDD (Isolated Direct Drive) Spindle Design and our ultra-wide, ultra-rigid internally ribbed construction, our FV-Series delivers exceptional cutting finish and accuracy.
With the addition of ATC system that changes tool-to-tool in 1 second for 30# spindle, and 3.5 seconds for 40# spindle, the newly developed NR type linear motion guide ways from THK, and the FANUC high responsive AC servo units, our FV-Series will more than pay for its value in no time, and we will bring you success.
1
2
F: 600mm/min.F: 23.62ipm
F: 5,000mm/min.F: 196.85ipm
Circularity: 5μF: 5,000mm/min.F: 196.85ipm
Circularity: 4μF: 600mm/min.F: 23.62ipm
Error: 6μ Error: 6μ
HEIDENHAINACCOM
HEIDENHAINACCOM
10μm /div 10μm /div
* Optional functions under FANUC MXP-200FB or MXP-200FC control system.
Conduct 45mm ■ 1.77" linear interpolation on XY plane with 600mm/min. 23.62ipm and 5,000mm/min. 196.85ipm cutting feed respectively.
Conduct R = 40mm ■ 1.58" circular interpolation on XY plane with 600mm/min. 23.62ipm and 5,000mm/min. 196.85ipm cutting feed respectively.
2
The most cost-effective solution in high-speed, high-precision mold & die machining.0.1μm High Resolution Modular (HRM)* + Simultaneously Differential Feedrate Control (SDFC)* Take a YCM FV-Series Vertical Machining Center with the HRM and SDFC functions, conduct tests and then check by Heidenhain Grid Encoder with the following results, which prove
HRM and SDFC not only enhance the feed rate control but also keep good accuracy.
Unique direct coupled spindle design could isolate heat source, reduce the thermal deformation, increase the spindle precision and prolong spindle life.
Isolated polyurethane flexible coupling is used between motor and spindle.
Optional spindle cooling system could achieve better accuracy control.
Direct power transfer from spindle shaft to the cutting edge, ensures the power efficiency. Detecting the spindle speed from the build-in encoder of spindle ensures the best performance of rigid tapping.
Unique Spindle IDD Design
3
Hi-Speed, Hi-Power Spindle Design
FV56T (30#)
■ Ceramic bearings are applied on 15,000rpm spindle, with features of lighter weight, low centrifugal force, high rigidity, low coefficient of heat expansion, so as to achieve better accuracy and spindle life.
■ High horse power design, maximum output for acceleration can achieve 20kW 27HP.
■ High torque, low inertia-form 0 to 6,000rpm takes only 0.3sec. to reach. Excellent in mass drilling and tapping works.
■ The high precision spindle bearing system, with ID. 45mm, is to match the small & precise mold making requirements.
■ Max. rigid tapping speed: 6,000rpm.
FV56A/85A/102A/125A (40#)
■ The 10000rpm spindle deploys precision ceramic ball bearings of light mass, low centrifugal force, low swell factor, but high rigidity, which assure the optimal accuracy and spindle life span.
■ Oil-Air lubrication 12,000rpm or 15,000rpm spindle is available for option.
4
Various High-Speed Spindle Options for Selection to Meet the Utmost Machining Requirements.
For : FV85A / FV102A / FV125A12,000rpm (opt.)
For : FV85A / FV102A / FV125A 15,000rpm (opt.)
For : FV56A / FV85A / FV102A / FV125A 10,000rpm (std.)
For : FV85A / FV102A / FV125A 10,000rpm (opt.)
For : FV56T - 15,000rpm
For : FV56A / FV85A / FV102A / FV125A12,000rpm (opt.)
15,000 1,500 2,100 4,500 8,000 10,0008,0005,5003,000
1,500 2,100 2,700 4,000 5,500 8,000 4,0008,000 10,000 12,000
12,0001,500 3,000 4,0008,000 1,500 15,000
1,500 10,000
5min.
5min.
5min.5min.
5min.
5min.5min.
5min.
1min.
1min.
2min. 2min.
5min.
5min.
3.7
0.54kgf-m0.36kgf-m
1.07kgf-m0.73kgf-m
2.14kgf-m1.46kgf-m
0.61kgf-m1.07kgf-m
0.45kgf-m
0.89kgf-m1.22kgf-m1.50kgf-m
0.61kgf-m 0.71kgf-m0.97kgf-m1.20kgf-m1.43kgf-m
0.49kgf-m
5
0.67 4.85
12.98 93.89
22 30
22 3011.69 84.56
12.98 93.89
11.69 84.56
12.98 93.89
18.5 25
22 30
18.5 25
L H L H
L HL H
2.38 17.21
6.96 50.34
5
High Efficiency Utmost performance Integration, Solution & Automation
Shuttle Type Automatic Pallet Changer (FV102A, Option)
■ APC's swivel arm is driven by X-axis servo motor with unique rack transmission design, features fast and accurate pallet change mechanism.
■ APC time is around 15 seconds.
■ Over sized taper pins are applied to ensure backlash-free positioning and rigid clamping on the pallet.
■ APC feed rate is adjustable to appropriate speed for different work pieces' demand.
Reliable ATC Unit
■ Fast and reliable roller gear cam ATC allows ATC time in 1 second (for FV56T), and 3.5 secods (for FV56A/FV85A/ FV102A/FV125A), lowers the idle time and enhances the machining efficiency.
■ The ATC units were running tested more than million times before their mass production to ensure high reliability.
Complete chips disposal system
■ Ensure the cleanness of machining environment. Optional flush coolant can be used to prove the chips disposal efficiently.
■ Screw type chip conveyor makes the chips disposal more easily & efficiently. (FV85A / FV102A)
■ Complete set of the Y-axis back side plate well protects the guide-way for durable operation.
Advanced APC Design (FV56T/A, Option)
■ Hi-speed rotary auto-pallet changer.
■ APC time takes 9 seconds only.
■ Reliable rotary mechanism driven by servo motor reducer achieves quick APC speed.
■ Rotary speed is adjustable to ensure better stability when heavy loading on the pallet.
■ Shot flush coolant could clean the positioning block automatically.
■ The minimum floor space required, saving floor space and saving money.
//
6
Extra Wide Machine Base 960mm 37.80"
FV56T Headstock
Extra Wide Column Base
Super-Accuracy & Rigidity Construction for High Speed Epoch ■ Tough and durable MEEHANITE castings deliver exceptional cutting stability and consistent accuracy - the massive,
rigid internally ribbed construction reduces damping effect for superb part finishing.
■ The extra wide column base and machine base maximize the cutting rigidity, and enhance machine stability during heavy-duty machining.
■ Hardened & ground ballscrews are precisely pre-tensioned at both ends, supported by angular contact thrust bearings, and directly coupled with high responsive AC servomotors of backlash-free for outstanding positioning repeatability and accuracy during long machining cycles.
■ All axes utilize the newly developed NR type linear motion guide ways from THK of its superior rigidity, low friction, low noise, thus to assure much smoother movement in high-speed traverse.
■ All linear motion guide ways are mounted on the very fine surface for maximum surface contact and exceptional cutting rigidity and stability.
Axial Rapid Feedrate (opt.)
X 36m/min. (48m/min.) 1,417ipm (1,890ipm)
Y 36m/min. (48m/min.) 1,417ipm (1,890ipm)
Z 24m/min. (48m/min.) 9,45ipm (1,890ipm)
//
7
Extra Wide Column Base
Extra Wide Machine Base 1,090mm 42.91"
Super-Accuracy & Rigidity Construction for High Speed Epoch ■ Tough and durable MEEHANITE castings deliver exceptional cutting stability and consistent accuracy - the
massive, rigid internally ribbed construction reduces damping effect for superb part finishing.
■ The extra wide column base and machine base maximize the cutting rigidity, and enhance machine stability during heavy-duty machining.
■ Hardened & ground ballscrews are precisely pre-tensioned at both ends, supported by angular contact thrust bearings, and directly coupled with high responsive AC servomotors of backlash-free for outstanding positioning repeatability and accuracy during long machining cycles.
■ All axes utilize the newly developed NR type linear motion guide ways from THK of its superior rigidity, low friction, low noise, thus to assure much smoother movement in high-speed traverse.
■ All linear motion guide ways are mounted on the very fine surface for maximum surface contact and exceptional cutting rigidity and stability.
Axial Rapid Feedrate
X 36m/min. 1,417ipm
Y 36m/min. 1,417ipm
Z 24m/min. 9,45ipm
//
8Extra Wide Machine Base 1,455mm 57.28"
Extra Wide Column Base
Y-Aaxis 4-Slideway Design
Super-Accuracy & Rigidity Construction for High Speed Epoch ■ Tough and durable MEEHANITE castings deliver exceptional cutting stability and consistent accuracy - the massive,
rigid internally ribbed construction reduces damping effect for superb part finishing.
■ The extra wide column base and machine base maximize the cutting rigidity, and enhance machine stability during heavy-duty machining.
■ Hardened & ground ballscrews are precisely pre-tensioned at both ends, supported by angular contact thrust bearings, and directly coupled with high responsive AC servomotors of backlash-free for outstanding positioning repeatability and accuracy during long machining cycles.
■ All axes utilize the newly developed NR type linear motion guide ways from THK of its superior rigidity, low friction, low noise, thus to assure much smoother movement in high-speed traverse.
■ All linear motion guide ways are mounted on the very fine surface for maximum surface contact and exceptional cutting rigidity and stability.
Axial Rapid Feedrate
X 24m/min. 9,45ipm
Y 24m/min. 9,45ipm
Z 24m/min. 9,45ipm
//
9
2,74
0 10
7.87
2,09
0 82
.28”
1,66
0 62
.35”
2,12
0 83
.46”
1,99
0 78
.35”
2,16
7 85
.31”
1,625 63.98”
2,280 89.76”
230
9.06
”
FV56
T : 2
,330
91.
73”
FV
56A
: 2,4
80 9
7.64
”
FV56A : 1,850 72.83”FV56T : 1,620 63.78”
678 23.62” (Door Open)
420 16.54100 100 110
700
27.
56
3.94 3.94 3.941103.94
Unit : mm inch
3.94 3.94 4.33
0.55
0.02
0.35
700
27.
56
420 16.54110100100
30°
14
2 0
.08
14 0.55
90.
5
27.5
1.0
8
23 0.91
H8
DIMENSIONS
*The appearance of the machines will be diverse due to different model and selectivity of controllers.
TABLE SIZE
T-SLOTS
//
10
FV85
A : 1
,000
39.
37 /
FV
102A
: 1,
120
44.0
9
60100 100100520 20.47
60 1002.36 2.363.943.94 3.94 3.94
0.71
18
321.26
31 1.22
0.5
0.02
13 0.51
H8
Unit : mm inch
FV85A : 2,150 84.65”
FV102A : 2,580 101.57”
3,040 119.69”
1,290 50.79”
216 8.5”
3,43
0 1
35.0
4”
R675
R26.57”
2,44
5 9
6.26
”
2,23
5 8
7.99
”
2,03
0 7
9.92
”
2,41
395
”
2,78
010
9.45
”(C
TS: 3
,110
122
.44”
)
2,300 90.55”150 5.91”
DIMENSIONS
*The appearance of the machines will be diverse due to different model and selectivity of controllers.
TABLE SIZE
T-SLOTS
11
2,07
0 8
1.5”
2,30
0 9
0.55
”
1,89
0 7
4.41
”
1,65
0 6
4.96
”
1,250 49.21”
3,100 122.05”
3,00
0 1
18.1
1”
2,46
6 9
7.09
”
2,12
5 8
3.66
”
R900
R35.43
”
3,500 137.8”
1,275 50.2”
1,05
0 4
3.34
”
2,50
0 9
8.43
”
2,24
0 8
8.19
”
2,9
75 1
17.1
3”
100 100 601001003.94 3.94 2.363.943.94
520 20.47
1350
53.
15
TABLE SIZE
Unit : mm inch
1350
53.
15
18
32 1.26
31 1
.22
0.5
0.0
2
100520 20.47
100 10010060
13 0
.51
H8
2.36 100100100100
0.71
//
*The appearance of the machines will be diverse due to different model and selectivity of controllers.
DIMENSIONS
T-SLOTS
12
2,500 98.43 (option)
2,19
0 86
.22
(top
cove
r , o
ptio
n)
FV56
A :2
,675
105
.31
(αT6
,C
TS*,
optio
n)
1,93
0 75
.98
1,17
5 4
6.26
2,18
5 8
6.02
1,960 77.17
3,095 121.85
R540R540
250 9.841,350 53.15
1957.68
1,850 72.83
3,29
5 1
29.7
2
250 9.84
2,230 87.80
R675
1,10
0 4
3.31
865
34.
06
800
31.
50
1,600 62.99
2,04
5 8
0.51
31012.20
2,21
0 8
7.01
2,15
5 84
.84
260
10.
24
FV56
T : 2
,145
84.
45 /
FV56
A : 2
,470
97.
24
R26.57
R21.2646
018
.11
R21.26
560
22.
05
240
9.4
524
0 9
.45
160
6.3
016
0 6
.30
8080
160 6.30160 6.30
80
410 16.14
ø13.5
118
22.5
0.8
9
0.5
0.0
2
M12x1.75P
3.15
3.15
803.15 3.15
ø0.53
APC TABLE SIZE SCREW HOLE
DIMENSIONS
Relevant Specifications of APC (Option)
Model FV56T FV56APallet Size 560 x 410mm 22.05" x 16.14"
Table Load Capacity 120kg 265 lbDistance Between Spindle Nose and Table Top
25 ~ 475mm 0.98"~18.70"
Axial Rapid Feedrate (X/Y/Z)
36/36/24 m/min. 1,417/1,417/945ipm
Machine Weight 3,630kg 8,003 lb 3,850kg 8,488 lb
Unit : mm inch
*The appearance of the machines will be diverse due to different model and selectivity of controllers.
//
DIMENSIONS
13
2,03
0 7
9.92
1,630 64.17
2,01
5 7
9.33
995
39.
17
170 6.69
2,820 111.02
2,45
5 9
6.65
920 36.22 (door open)
87034.25
63525
1,210+4047.64+1.57(handle)
4,090 161.02
2,525 99.41
1,36
553
.74
3,475 136.81
1,35
0 5
3.15
1,360 53.54 2459.65
1,68
0 6
6.14
4,09
0 1
61.0
2
67526.57
R400R15.75
CTS
* : 3
,110
122.
442,
920
114.
96 (M
AX
.)
240 9.45
3 0.12
100x
91,
000
39.
37
500
19.
69
50 1
.97
100x4480 18.90
40 1.57
60°
60°
60°
60°
M16x2P
120°ø20
35 452C
18
2C
6
18
ø50
ø110
2C 2C
Relevant Specifications of APC (Option)
Model FV102APallet Size 1,000 x 480mm 39.37" x 18.9"
Table Load Capacity 400kg 882 lbDistance Between Spindle Nose and Table Top
30~570mm 1.18"~22.44"
Axial Rapid Feedrate (X/Y/Z)
24/24/24 m/min. 945/945/945ipm
Machine Weight 6,360kg 14,021 lb
Unit : mm inch
// DIMENSIONS
*The appearance of the machines will be diverse due to different model and selectivity of controllers.
TABLE SIZE SCREW HOLE
DIMENSIONS
OPERATIONOPERATION
CONTROLby
User-friendly G-menu function provides multiple machining cycles that greatly simplifies programming steps
Detailed troubleshooting procedures will be automatically displayed when machine alarm occurs that allows users to restore machine status and minimize down time
Comprehensive tool data management function allows operators to monitor and manage all positions in tool magazine
Intelligent Tool Data Management
Pre-set macros and graphical procedure are provided for automatic tool length measurement function
Automatic Tool LengthMeasurement
Easy setup of tool length measurement provides convenient settingof tool offsets data fromone tool to another
Manual Tool LengthMeasurement
Easy to use conversational software offers convenience of part programming right on the shop-floor with 3D graphical display and full simulation function
Pre-set maintenanceschedules are programmedto remind operators toinspect periodicallyprolonging machine life
Intelligent MaintenanceReminder
Allows user to easily keep track on number of workpieces with:Main CounterPeriodical CounterDaily CounterOver Cycle Alarm
Counter Function
Pop-up Alarm Display
Convenient calculator function provides fast calculation and setting of workpiece offsets
Artificially intelligent machining function that is developed from accumulation of all YCM knowledge and experience on high speed to achieve the fastest cycle time with best machining results. Machining efficiency improved by 25% without sacrificing machining accuracy.
Easy Shop-floor ProgrammingManual Guide i
G-menu Function Calculator Function
Easily select multiple windows from the following list of display for your monitoring needs.
Tool DataWork Coordination
Parts CountMachining Hours
G-code StatusM-code StatusSpindle Status
Multi-function Display
High Speed Machining Mode: M400
Wireless Message Notification (opt.)
Integrating GSM communication and CNC technology, YCM developed the WMN system for wireless notification of machine and work status report.
Date and TimeController Running Hours Spindle Load Function Display
Software enhancement exclusively from YCM
Combined with artificial intelligence, M400 provides users more convenient and easier ways of operation and achieves fast cycle time for the best machining result.
High Speed Machining Mode: M400
Feedrate
YCMWORKPIECESTATUS:COMPLETE
High Performance AC Digital Servo & Spindle Drives with Super Precision Absolute Positioning EncodersAI NANO CNC Controller for High Precision Operation in Nanometers and Acknowledged HRV ControlAICC II High Speed High Accuracy JERK Function & Auto Switching on/off Machining Control FunctionHigh Speed High Accuracy Rigid Tapping, Helical Interpolation, Custom Marco B, and Tool Path GraphicsManual Guide i with Big & Double Screen Display (MXP-200FC, opt.)Program File Management for Easy Program ClassifyingUSB Drive Port for Easy Parameters & CNC Programs TransferLarge Program Capacity with 1,280 Meters of MemoryHigh Speed Positioning Function (MXP-200FC, opt.)Memory Card Program Edit & Operation (opt.)3D Interference Check (opt.)NANO Smooth (opt.)
1. The manufacturer reserves the right to modify the design, specifications, mechanisms, etc. to improve the performance of the machine without notice. All the specifications shown above are just for reference.2. The functions of the controllers will be distinct due to different model and selectivity.
OPERATIONOPERATION
CONTROLby
User-friendly G-menu function provides multiple machining cycles that greatly simplifies programming steps
Detailed troubleshooting procedures will be automatically displayed when machine alarm occurs that allows users to restore machine status and minimize down time
Comprehensive tool data management function allows operators to monitor and manage all positions in tool magazine
Intelligent Tool Data Management
Pre-set macros and graphical procedure are provided for automatic tool length measurement function
Automatic Tool LengthMeasurement
Easy setup of tool length measurement provides convenient settingof tool offsets data fromone tool to another
Manual Tool LengthMeasurement
Easy to use conversational software offers convenience of part programming right on the shop-floor with 3D graphical display and full simulation function
Pre-set maintenanceschedules are programmedto remind operators toinspect periodicallyprolonging machine life
Intelligent MaintenanceReminder
Allows user to easily keep track on number of workpieces with:Main CounterPeriodical CounterDaily CounterOver Cycle Alarm
Counter Function
Pop-up Alarm Display
Convenient calculator function provides fast calculation and setting of workpiece offsets
Artificially intelligent machining function that is developed from accumulation of all YCM knowledge and experience on high speed to achieve the fastest cycle time with best machining results. Machining efficiency improved by 25% without sacrificing machining accuracy.
Easy Shop-floor ProgrammingManual Guide i
G-menu Function Calculator Function
Easily select multiple windows from the following list of display for your monitoring needs.
Tool DataWork Coordination
Parts CountMachining Hours
G-code StatusM-code StatusSpindle Status
Multi-function Display
High Speed Machining Mode: M400
Wireless Message Notification (opt.)
Integrating GSM communication and CNC technology, YCM developed the WMN system for wireless notification of machine and work status report.
Date and TimeController Running Hours Spindle Load Function Display
Software enhancement exclusively from YCM
Combined with artificial intelligence, M400 provides users more convenient and easier ways of operation and achieves fast cycle time for the best machining result.
High Speed Machining Mode: M400
Feedrate
YCMWORKPIECESTATUS:COMPLETE
High Performance AC Digital Servo & Spindle Drives with Super Precision Absolute Positioning EncodersAI NANO CNC Controller for High Precision Operation in Nanometers and Acknowledged HRV ControlAICC II High Speed High Accuracy JERK Function & Auto Switching on/off Machining Control FunctionHigh Speed High Accuracy Rigid Tapping, Helical Interpolation, Custom Marco B, and Tool Path GraphicsManual Guide i with Big & Double Screen Display (MXP-200FC, opt.)Program File Management for Easy Program ClassifyingUSB Drive Port for Easy Parameters & CNC Programs TransferLarge Program Capacity with 1,280 Meters of MemoryHigh Speed Positioning Function (MXP-200FC, opt.)Memory Card Program Edit & Operation (opt.)3D Interference Check (opt.)NANO Smooth (opt.)
1. The manufacturer reserves the right to modify the design, specifications, mechanisms, etc. to improve the performance of the machine without notice. All the specifications shown above are just for reference.2. The functions of the controllers will be distinct due to different model and selectivity.
OPERATIONOPERATION
CONTROLby
User-friendly G-menu function provides multiple machining cycles that greatly simplifies programming steps
Detailed troubleshooting procedures will be automatically displayed when machine alarm occurs that allows users to restore machine status and minimize down time
Comprehensive tool data management function allows operators to monitor and manage all positions in tool magazine
Intelligent Tool Data Management
Pre-set macros and graphical procedure are provided for automatic tool length measurement function
Automatic Tool LengthMeasurement
Easy setup of tool length measurement provides convenient settingof tool offsets data fromone tool to another
Manual Tool LengthMeasurement
Easy to use conversational software offers convenience of part programming right on the shop-floor with 3D graphical display and full simulation function
Pre-set maintenanceschedules are programmedto remind operators toinspect periodicallyprolonging machine life
Intelligent MaintenanceReminder
Allows user to easily keep track on number of workpieces with:Main CounterPeriodical CounterDaily CounterOver Cycle Alarm
Counter Function
Pop-up Alarm Display
Convenient calculator function provides fast calculation and setting of workpiece offsets
Artificially intelligent machining function that is developed from accumulation of all YCM knowledge and experience on high speed to achieve the fastest cycle time with best machining results. Machining efficiency improved by 25% without sacrificing machining accuracy.
Easy Shop-floor ProgrammingManual Guide i
G-menu Function Calculator Function
Easily select multiple windows from the following list of display for your monitoring needs.
Tool DataWork Coordination
Parts CountMachining Hours
G-code StatusM-code StatusSpindle Status
Multi-function Display
High Speed Machining Mode: M400
Wireless Message Notification (opt.)
Integrating GSM communication and CNC technology, YCM developed the WMN system for wireless notification of machine and work status report.
Date and TimeController Running Hours Spindle Load Function Display
Software enhancement exclusively from YCM
Combined with artificial intelligence, M400 provides users more convenient and easier ways of operation and achieves fast cycle time for the best machining result.
High Speed Machining Mode: M400
Feedrate
YCMWORKPIECESTATUS:COMPLETE
High Performance AC Digital Servo & Spindle Drives with Super Precision Absolute Positioning EncodersAI NANO CNC Controller for High Precision Operation in Nanometers and Acknowledged HRV ControlAICC II High Speed High Accuracy JERK Function & Auto Switching on/off Machining Control FunctionHigh Speed High Accuracy Rigid Tapping, Helical Interpolation, Custom Marco B, and Tool Path GraphicsManual Guide i with Big & Double Screen Display (MXP-200FC, opt.)Program File Management for Easy Program ClassifyingUSB Drive Port for Easy Parameters & CNC Programs TransferLarge Program Capacity with 1,280 Meters of MemoryHigh Speed Positioning Function (MXP-200FC, opt.)Memory Card Program Edit & Operation (opt.)3D Interference Check (opt.)NANO Smooth (opt.)
1. The manufacturer reserves the right to modify the design, specifications, mechanisms, etc. to improve the performance of the machine without notice. All the specifications shown above are just for reference.2. The functions of the controllers will be distinct due to different model and selectivity.