SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401...

14
www.mouvex.com SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities B 200-10L 700 to 1000 rpm B 200-12R 840 to 1200 rpm Dimensions : L 436 x H 215x l 133 mm Weight : 26,5 kg Gravity torque : under 50 Nm Screw compressor B 200 For liquids 120 to 180m 3 /hr Splined shaft for direct flange mounting on PTO PF Option - PTO Flange Straight Keyed shaft for electric motor drive PS Option - PTO Shaft Femele spline shaft for hydraulic motor drive HY Option - hydraulic

Transcript of SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401...

Page 1: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

www.mouvex.com

SPEC SHEET 1401-012 ESECTION : 1401Effective January 2010Replaces : New

The solution for an optimum direct mounting3 possibilities

B 200-10L700 to 1000 rpm

B 200-12R840 to 1200 rpm

Dimensions :L 436 x H 215x l 133 mm

Weight : 26,5 kg

Gravity torque : under 50 Nm

Screw compressorB 200For liquids

120 to 180m3/hr

Splined shaftfor direct flange

mounting on PTO

PF Option - PTO Flange

Straight Keyed shaftfor electricmotor drive

PS Option - PTO Shaft

Femele spline shaftfor hydraulicmotor drive

HY Option - hydraulic

Page 2: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

ZI la Plaine des Islesrue des Caillottes89000 AUXERRE - FRANCET + 33.3.86.49.86.30 F + [email protected]

www.mouvex.com

Distributed by :

* At full speed.

Mouvex reserves the right to modify the information and illustrations contained in this documentwithout prior notice. This is a non-contractual document. 01/09Printed in FRANCE by Filigrane© 2010 Mouvex

50

60

70

80

90

100

110

120

130

140

150

160

170

180

190

200

0 0,5 1 1,5 2 2,5

EXHAUST PRESSURE bar

SUC

TIO

N F

LOW

RA

TE m

3/h

4

6

8

10

12

14

16

POW

ER k

W

Suction : 1 atm , 20°C Flow measurement : ISO 5167-2

BE 10385A 20/05/09

Screw compressor B 200

� Speed (rpm)COMPRESSOR SPEED

VERSION 1 2 3 4

12R 840 960 1080 1200

10L 700 800 900 1000

� Flow (m3/hr) / Power (kW)

� Torque / Pressure (Nm)

Pressure (bar)*VERSION 1.5 2.0 2.5

12R 100 111 124

10L 83 93 103

PS Option - PTO Shaft

HY Option - Hydraulic

PF Option - PTO Flange

SU

CT

ION

FLO

W m

3/h

r

EXHAUST PRESSURE (bar)

PO

WE

R k

W

cannelures / (Splines)ANSI B92-1a7/8n SAE_16/32 Spline pitch13 dents / (teeth)

6 Trous / (Holes) Ø 10.2

For flange SAE B (2 or 4 holes)

Key : large 8 mm

Page 3: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

Spec Sheet 208-001 E Section: 200Effective: April 2014Replaces: September 2010

Historical partnerFrom the collaboration between HAMMOND and MOUVEX, the Enterprise series is the result of long experience that stands out today as the vane compressor of reference.

Legendary robustnessThe body and rotor are contructed of hard-coated cast iron to withstand harsh environmental and operating conditions, with strength unmatched in the industry.

Corrosion freeThe integral anticorrosion coating of the compressor and the check relief valve, combined with stainless steel flanges, guarantee peace of mind.

Quality of the accessoriesThe new, extra-long inlet connection kit allows for deporting the air filter and insures perfect waterproofing.

ENTERPRISE Series Vane Compressor for Liquids to 170 m3/h

E170 Vane Compressor

E140 Vane Compressor

Enterprise Check Relief Valve

E140: 1,000/1,750 rpm

E170: 1,000/1,600 rpm

Dimensions: L 490/570 x H 220 x l 220 mm

L 19/23 x H 9 x l 9 in.

Weight: 36 kg (79 lbs.) to 47 kg (104 lbs.)

Page 4: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

ZI la Plaine des Isles • 2 rue des CaillottesF-89000 AUXERRE - FRANCE

Tel: + 33.3.86.49.86.30 • Fax: + [email protected] www.mouvex.com

Dimensions

Technical Specifications

CompressorA B C

in. mm in. mm in. mm

E140 9 1/2 240 9 7/8 250 17 7/8 454

E170 11 280 117/16 290 191/2 494

WeightCompressor lbs. kg

E140 79 36

E170 104 47

E140 E170

Air Delivered m3/hr (CFM) 140 (82) 170 (102)

Maximum Continuous Pressure bar-g (PSIG) 2.5 (36) 2.0 (29)

Pressure – 1500 rpm – Kw (HP) PowerAbsorbed @ Maximum 8.4 (11.3) 10.2 (13.7)

Maximum Speed (rpm) 1,750 1,600

DischargeE140 1.5" NPT flange

E170 1.5" NPT flange

ENTERPRISE Series Vane Compressors for Liquids to 170 m3/h

Distributed By:

Mouvex reserves the right to modify the information and illustrations contained in this document without prior notice. This is a not-contractual document.

© 2014 Pump Solutions Group (PSG), a Dover Company MVX-30000-T-01

(3¹/") (6¹¹/")

(8¹¹/")

(4³/")

(8¹¹/")

(3¹/") (6¹¹/")

(8¹¹/")

(4³/")

(8¹¹/")

Options and AccessoriesThe Enterprise Series compressors are available in PTO or Hydraulic Motor drive versions. Accessories available include:

Option: Enterprise with Hydraulic motor drive adaptor

Hydrive Hydraulic Cooler (optional)

Enterprise Check and Relief Valve (Delivered with Enterprise Series)

Suction Filter (optional)

Inlet Connection Kit (Delivered with Enterprise Series)

Page 5: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

CC20Eccentric Disc Pump

Spec Sheet 1004-001 E Section: 1001

Effective: September 2012

Replaces: July 2011

Design• Features and Benefits: Excellent self priming

capacity, constant and smooth delivery, line stripping capability, small package size, lightweight, easy to install. The Mouvex CC20 pump is an excellent truck mounted solution to load and off-load tank trucks and transports.

• The unique, durable design allows for leak-free operation and consistent flow rates over time resulting in low life-cycle costs.

• Its multi-purpose application also enables it to be used as a base mounted unit.

Application• Collection and transfer of used oil/waste oil and used anti-freeze

Operation• Principle Eccentric Disc, positive displacement

• Installation Can be mounted in any position

• Drive Truck mounted – PTO, hydraulic motor drive, or engine drive

Base mounted – electric motor or engine drive

Flow Rate• Up to 88 gpm (20 m3/h)

Page 6: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

Printed in USA

Distributed by:

© 2012 Mouvex

ZI la Plaine des Isles2 rue des Caillottes

F-89000 AUXERRE - FRANCETél : + 33.3.86.49.86.30Fax: + 33.3.86.46.42.10

[email protected]

Description of Construction• Standard construction: Cast iron piston and head, steel shaft

and ball bearings, bronze bushings, WNCN mechanical seal, Nitrile O-rings and bronze compensated relief valve

• Output shaft: Steel ball bearings

• Shaft seal: Mechanical (no packing gland)

• Relief valve: Adjustable built-in relief valve

• Delivered with 3” weld flanges

• Cast iron and steel construction

• Optional construction: “Used oil and lubricants” construction. This option is especially suited for the pumping of difficult products as well as the collection and transfer of waste oil and lubricants.

Options• Electric motor driven

• Diesel engine driven

• Hydraulic motor drive

Mouvex reserves the right to modify the information and illustrations contained in this documentwithout prior notice. This is a not-contractual document.

CC20Eccentric Disc Pump

Rotation Speed

Flow RateMaximum Pressure

ViscosityPower

Required

rpm m3/h gpm bar psi cSt ssu kW HP

300 12 53 3.4 50 2000 9600 1.1 1.5

400 16 70 3.4 50 1000 4800 1.5 2.0

500 20 88 3.4 50 750 3600 1.8 2.4

Page 7: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

www.mouvex.com

The Mouvex Food Transport solution

BLK 4-T Positive Displacement Lobe Pump

TECHNICAL DATA SHEET 1701-001 ECHAPTER: 100Effective from: June 2009Replaces: CCL 50i

The new BLK 4-T lobe Pump takes over from the tireless CCL 50i.More compact it will be your best ally to satisfy the ever-increasing transport requirements.

Reliable:• The same key components of the former CCL50i are used in the BLK4T,

the parts that created the like exclusive reputation. Shaft seal made of PTFE.

• Easy to clean in all circumstances, it is also easy to take apart in few seconds with usual tools and the lobe extractor supplied with each pump.

• The robust front cover seal remains in place, in the pump casing.

Adaptable:• Compact, easy to fit in narrow areas.• Hollow shaft for hydraulic drive systems or standard shaft

for electrical drive.• Optional: heating jacket, on the front cover.• Optional: internal relief valve .• Reversible.

Clean:• High grade polished surface.• Food grade lubricant in the gear box.

Up to 42 m3/h - 7 bar

Page 8: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

ZI la Plaine des Islesrue des Caillottes89000 AUXERRE - FRANCET + 33.3.86.49.86.30 F + [email protected]

Votre distributeur :

www.mouvex.com

Dimensions

Packages available

� Operating limits:

Flow rate 42 m3/h

Speed 720 rpm

Pressure 7 bar

Temperature 120°C

� Flow rate graph (viscosity of 500 cst):

� ��� ��� ��� ��� ��� ��� �� ���

��

��

��

��

��

��

��

��

�� ������ ����

���� �������

� Hydraulic drive: � Electrical drive:

Hydraulic motor: Inverter Speed variator

Hydraulic pumpHydrive cooler

Wet parts made of 316L stainless steel.

Materials EPDM O rings, FDA type

Shaft seal PTFE

Shaft seal with 3 lip seals

Standard connections DIN 80 and DIN 100

Rotor: Tri lobe

Equipment Shaft 1 hollow SAE 6B Ø 1’

Shaft 2 male output Ø 38

Heating jacket as an option

Internal relief valve as an option

Direction of rotation Reversible

Mounting Horizontal or vertical

Standard 3A – compliant

Weight 65 Kg

Flow

rate

(m3 /h

)

Speed (rpm)

190

290

143,5

DIN-80

DIN-10

0

SAE 6B 1”internal spline

53,2 53,2

105 100120

100120

M12

385290

297137 160

Distributed by:

Page 9: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

www.mouvex.com

Petroleum product transfer on tanker, the Mouvex solution.

CC8 Vanes pump series

SAFETY:• ATEX certified pump with a temperature probe • Integrated by-pass avoiding any over pressure • The unused ended shaft is protected by a casing

Universality:• Compatible with diesel, heating oil, petrol, biodiesel, paraffin,

kerosene, oil, heavy fuel, bitumen … • Compact and so fits in narrow spaces • Double ended shaft facilitates the mounting depending

on the rotation directions • Broad flow range

User Friendly:• Silent • Constant flow rate • Drains the pipes

Reliability:• Its robust construction allows working in the heavy duty application

of the road transports

Up to 80 m3/h - 8 bar

TECHNICAL LEAFLET 1801-003 ERUBRIQUE : 1801Valid since : July 2009Remplaced : June 2006

The CC8 pump range has been a major player in the Europeanmarket for many years.

� Universal joint driven

� Hydraulic driven

� Diesel driven

Page 10: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

TYPE DESCRIPTION

Mechanical 4 bar spring

By-PassMechanical 8 bar springPneumatic with springPneumatic without springSteel Ø 91Stainless steel Ø 91

Flanges Steel Ø 115Cast iron type BSM bore G 2,5Cast iron type BSM bore G 3

TYPE DESCRIPTION

By-Pass Pneumatic with springFlanges Steel Ø 115

The CC8 pumps versions A & AP are designed for clean products at room temperature

Uses

VERSION MODEL APPLICATION MAXIMUM VISCOSITY MAXIMUM TEMPERATURE

CC8-40

ACC8-50 Diesel, biodiesel

40 cstCC8-65 heating oil, petrol,70°CCC8-80 F kerosene, parrafin

APCC8-50

Oils 900 cstCC8-65

Dimensions Equipment

E - by-pass settingJ - space for head dismantling P - pump plate

V - drain plug V1-V2 - pressure / vacuum take off

Page 11: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

Flow rate in m3/h

Examples

MODEL MAXIMUM PRESSURE 8 BAR MAXIMUM PRESSURE 4 BAR

SPEED (RPM)

50 200 500 750 1000 1200

CC8-40 19 28 40 48CC8-50

24 36 47CC8-50AP 2 8CC8-65A

28 42 61CC8-65AP 2,5 10CC8-80F 40 60 81

CONSTRUCTION COMPONENT QUANTITY MATERIAL

Casing & head 1, 2 cast iron

Shaft 1 steel

BASISRotor 1 cast iron

Static seal - Nitrile

Mechanical seal - FKM

Mechanical seal 2 Carbon/SS

A Vanes 6 TVR

AP Vanes 12 TVP

Pushrods 6 Hardened steel

Material of construction

� AD truck with CC8-50 A

� Semi-trailor with CC8-65 A

Page 12: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

ZI la Plaine des Islesrue des Caillottes89000 AUXERRE - FRANCET + 33.3.86.49.86.30 F + [email protected]

www.mouvex.com

Votre distributeur :

The CC8 pump versions C & EP are designed for clean hot products, there are 2 versions

VERSION MODEL APPLICATION MAXIMUM VISCOSITY (cst) MAXIMUMDepending on speed (rpm) TEMPERATURE In °C

50 400 550 750

C CC8-65 heavy fuel 900 900 400 170EP CC8-65 Bitumen 5000 3000 2000 1000 200

TYPE DESCRIPTION Construction

By-PassMechanical 4 bar spring � �

Mechanical 8 bar spring � �

Foot With or without � �

Head With heating jacket �

Steel Ø 91 mm � �

Stainless steel Ø 91 mm � �

Flanges Steel Ø 115 mm � �

Cast iron type BSM � �Bore G 2,5

Cast iron type BSM � �Bore G 3

Dimensions Equipment

C EP

Flow rate in m3/h

MODEL MAXIMUM PRESSURE 6 BAR

50 400 550 750

CC8-65C25 34 43

CC8-65EP 2

CONSTRUCTION COMPONENT QUANTITY MATERIAL

Casing & head 1 Cast iron

BASISShaft 1 Steel

Rotor 1 Cast iron

Mechanical seal 2 Bronze/Stainless steel

C Mechanical seal - FKM

Static seal - FKM

Vanes 6 Bronze

EP Mechanica seal - FKM - high temperature

Static seal - FKM - high temperature

Vanes 6 Special bronze

Pushrods 3 Hardened steel

Material of construction

V1-V2 - pressure/vacuum take offE - by-pass settingJ - space for dismantlingP - pump plateA - heating jacket ports

Distributed by:

Mouvex reserves the right to modify the information and illustrations contained in this document without priornotice. This is a not-contractual document. 05/2010. Printed in FRANCE by Italic Impressions. © 2010 Mouvex

Page 13: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

Reliability Durable pumps for fast and quiet operation.Sliding vane design provides sustained performance and trouble free operation.

Unique FeaturesAdjustable relief valve protects pump from excessive pressure. Optional air operated relief valve offers easy hose and nozzle handling. T-type strainers are available to protect pumping systems from damage caused by welding slag and foreign matter in the piping and tanks.

Sizing OptionsAvailable in 1.5, 2, 2.5, 3, and 4-inch port sizes with flow rates from 10 to 500 U.S. gallons (2 to 113 m3/h) and pressures up to 125 psi (8.6 bar).

Applications

TXSD models are equipped with a nickel-plated relief valve ideal for handling solvents, and FKM elastomers that are compatible with all Biodiesel and Ethanol blends.

TX, TXD & TXSD SeriesSliding Vane Pumps

How Blackmer’s sliding vane action works

■ Fuel oil delivery truck

■ Fleet refueling

■ Lube oil

■ Aviation refuelers

■ Transport of · petro chemicals · gasoline · biofuels · solvents · and many more

www.blackmer.com

SPEC SHEET 201-001

Section: 201Effective: April 2009Replaces: September 2006

Page 14: SPEC SHEET 1401-012 E 1401 January 2010 New Screw ... · SPEC SHEET 1401-012 E SECTION : 1401 Effective January 2010 Replaces : New The solution for an optimum direct mounting 3 possibilities

Pump Model TX1.5 TX(S)D2 TX(S)D2.5 TX(S)D3 TX4 Rated Pump

Speed 780 600 400 640 520 640 520 640 520 500 400

gpm 52 40 25 72 58 120 98 263 211 505 405L/min 197 151 95 273 220 454 371 995 799 1,911 1,533m3/h 12 9 6 16 13 27 22 60 48 115 92hp 2.4 1.9 1.3 3.0 2.5 5.0 3.8 11.1 8.6 18.2 15kW 1.8 1.4 1.0 2.2 1.9 3.7 2.8 8.3 6.4 13.6 11.2

Performance Data

* Appropriate capacities and horsepower (hp) are based on a 100 ssu (22 cP) fluid a 50 psi (3.4 bar) delivered pressure. Refer to Characteristic Curves for flow rates and torque requirements at other pressures and viscosities.

TX, TXD & TXSD Series Sliding Vane Pumps

Options■ FKM or PTFE O-rings■ Me chanical seals with

stainless steel stationary seats

■ Laminate vanes■ Pneumatic relief valve■ Hydraulic Motor Adapters ■ Strainers

Pump ModelNominal Flowrate Pump Speed Viscosity Differential Pressure Working Pressure Temperature

gpm L/min. rpm ssu cP psi bar psi bar ºF ºC

TX1.5 56 212 780 20,000 4,250 125 8.6 175 12.1 300 149

TX(S)D2 87 329 780 20,000 4,250 125 8.6 175 12.1 300 149

TX(S)D2.5 157 594 780 20,000 4,250 125 8.6 175 12.1 300 149

TX(S)D3 270 1,022 640 20,000 4,250 125 8.6 175 12.1 300 149

TX4 505 1,911 500 20,000 4,250 125 8.6 175 12.1 240 116

Maximum Operating Limits

Model A B D E G K M Q S T AA BB DD TT Approx. Wt.

TX1.5in. 11/8 1/4 713/16 51/16 31/8 61/2 4 81/2 7 39/16 – – 103/8 – 61 lbs.

mm – – 198 129 79 165 102 216 178 90 – – 264 – 28 kg11⁄4" HYD Motor Shaft

1" HYD Motor Shaft

TX(S)D2in. 11/8 1/4 8 51/4 31/2 61/2 4 811/16 61/8 37/8 83/4 85/16 107/8 109/16 121/8 70 lbs.

mm – – 203 133 89 165 102 221 156 98 222 211 276 268 308 32 kg

TX(S)D2.5in. 11/8 1/4 83/4 6 47/8 7 4 95/8 613/16 315/16 91/2 811/16 115/8 115/16 135/16 94 lbs.

mm – – 222 152 124 178 102 244 173 100 241 221 295 287 338 43 kg

TX(S)D3in. 11/8 1/4 95/8 67/16 43/8 71/4 53/8 1213/16 89/16 415/16 1011/16 97/16 123/8 153/8 152 lbs.

mm – – 244 164 111 184 137 325 217 125 271 240 314 391 69 kg

TX4in. 11/2 3/8 11 81/4 7 91/2 63/8 151/2 81/2 63/8 – – – – 295 lbs.

mm – – 279 210 178 241 162 394 217 162 – – – – 134 kg

Dimensions

Pump RotationBlackmer TX(S)D models are equipped with a double-ended drive shaft for either clockwise (RH) or counterclockwise (LH) rotation. Standard rotation for the TX1.5 is counterclockwise (LH) when viewed from the drive shaft. Standard rotation for the TX4 model is clockwise (RH).

www.blackmer.com

Blackmer World Headquarters1809 Century Avenue SW

Grand Rapids, MI 49503-1530 USAT 616.241.1611 F 616.241.3752

Printed in USA © 2009 Blackmer