Spec 3800
Click here to load reader
-
Upload
lowys235375 -
Category
Documents
-
view
215 -
download
1
description
Transcript of Spec 3800
APPLICATIONCat. No. 3800 devices are designed for mounting in standard equipment cabinets where transient volt-age surge suppression is desired for the enclosed equipment. The MOV-based circuit design of eachmodule provides Normal Mode and Common Mode protection for line to neutral, line to ground and neu-tral to ground. The 3800 modules feature compact “black box” styling. Three modules are available:DIN-rail mounting, terminal block wiring or wire leads.
STANDARDS SPECIFICATIONSThe Cat No. 3800 Equipment-Cabinet Surge Protective Devices (SPD) are designed for use on 120Vsingle-phase AC power lines. The 3800-OWM, DIN and OEM modules feature a green LED monitor toindicate loss of protection. (Light out indicates that protection is lost, replace unit.) In the event protec-tion is lost, unit will continue to provide power to connected loads. These devices are UL RecognizedComponent TVSS 1449 Standard. The Cat. No. 3800 is backed by Leviton’s limited five year warranty.
R
SPECIFIER PRODUCT INFORMATION
CAT. NO. 3800 EQUIPMENT-CABINET SURGE PROTECTIVE DEVICES
UL 1449 Transient Voltage Surge Suppressors
GENERAL DATA FOR CAT. NO. 3800
Specification Data Applicable To All
Rated line voltage 120V (VRMS)
Maximum continuous 135Voperating voltage
Max. single-pulse transient current 13000A (L-N)(8x20 µs, Amps peak) 6500A (L-G)
6500A (N-G)
Rated single-pulse transient energy 280 Joules(10x1000 µs, impulse)
Noise rejection @ 5kHz-5MHz -35 dB
Dat
e of
Iss
ue:
Oct
ober
, 19
96N61
Cat. No. 3800-DIN
©1996 Leviton Manufacturing Co., Inc. All Rights Reserved C-481/J6
R
SPECIFIER PRODUCT INFORMATIONN62
Specification 3800-OWM, DIN 3800-OEM*
UL Standard 1449 L-N: 500V Peak L-N: 600 Peak
Permanently-wired L-G: 500V Peak L-G: 600 Peak
Test (8x20 µs, 3000A) N-G: 500V Peak N-G: 600 Peak
Operating Temperature Range: -10°C to 60°C
Storage Temperature Range: -20°C to 85°C
Wiring Means:
Nos. 3800-DIN, 3800-OWM Terminal block accepts 22 AWG to 12 AWG conductors
No. 3800-OEM #16 AWG leads, 6” long, stripped 1/2”
Agency Approvals All devices UL Recognized Component TVSS1449 Standard, CSA Certified
LIGHT ONSURGE
PROTECTED
1.66 (42.16mm)
0.83(21.08mm)
2.69
(68
.33m
m)
3.28
(83
.31m
m)
3.78
(96
.01m
m)
0.625(15.88mm)
TERMINAL BLOCK
1.41
(35
.81m
m)
NOTE: WIRES ENTERFROM THIS SIDE
0.73(18.54mm)
0.85 (21.59mm)
DIN RAIL CLIP
CLAMPING PERFORMANCE
PHYSICAL SPECIFICATIONS
SUPPRESSION MODULES FOR EQUIPMENT CABINETS
*3800-OEM rating tested with 6” lead length
Cat. No. Description
3800-DIN For DIN rail mounting, with terminal block
3800-OWM Screw mounting, with terminal block
3800-OEM Screw mounting, with pigtail wire leads