Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m29-1

SPECIALTY HARDWARE

Revised 05/02/16

CONTENTSThis section contains miscellaneous door hardware and hotel entry sets.

TABLE OF CONTENTS:

Saddle Entry Sets Pages 29-2 – 29-3

Contemporary Entry Sets Pages 29-4 – 29-5

Rim Lock Sets Pages 29-6 – 29-7

Contemporary Sets w/Concealed Screws Pages 29-8 – 29-19

Minimalist Sets Pages 29-20 – 29-24

The Lift Sets Pages 29-25 – 29-30

Hotel Entry Sets Page 29-31

ORDERING INSTRUCTIONS:

Specialty Hardware: See Ordering Instructions in Binder 1/ Dealer Information. Custom Specialty Hardware: See Custom Ordering Instructions in Binder 1/ Dealer Information.

DOOR HANDING GUIDE:

Right Hand (RH)Left Hand (LH)OUTSIDE

INSIDE

Right Hand Reverse (RHR)Left Hand Reverse (LHR)OUTSIDE

INSIDE

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-2

Revised 05/02/16

Illustrations are for demonstration purposes only. Available knob or lever high or low. Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Flush mount entry set. Plates DO NOT wrap door edge.Door template must be provided with door edge bevel.Requires 2 1/4” minimum door thickness.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Flush mount entry set. Plates DO NOT wrap door edge.Door template must be provided with door edge bevel.Requires 2 1/4” minimum door thickness. Specify manufacturer and function of lock to be used.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Shown with 5” backset.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included.

2500 SADDLE ENTRY SETS

14"

10" 10"

14"

10" 10"

14"

10" 10"

14"

10" 10"

CS-2500ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – No key cover. OR TS-2500ML – Trim set only. No lock.

CS-2500ML-DC – Complete set with mortise lock, cylinder and spindle. – Double cylinder. – No key cover. OR TS-2500ML-DC – Trim set only. No lock.

CS-2500ML-PF – Complete set with mortise lock and spindle. – Patio function. OR TS-2500ML-PF – Trim set only. No lock.

CS-2500ML-FD – Trim set only. – Full dummy.

3 5/

8"

2 7/

16"

3 5/

8"

2 7/

16"5

3/16

"5

3/16

"

CS-2500ML Single cylinder. Knob x knob or lever x lever entry set.

CS-2500ML-DC Double cylinder. Knob x knob or lever x lever entry set.

CS-2500ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-2500ML-FD Full dummy. Knob x knob or lever x lever dummy set.

TS-2500ML Single cylinder. Knob x knob or lever x lever entry set.

TS-2500ML-DC Double cylinder. Knob x knob or lever x lever entry set.

TS-2500ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-2500ML–FD Full dummy. Knob x knob or lever x lever dummy set.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-3

Revised 05/02/16

Illustrations are for demonstration purposes only. Available knob or lever high or low. Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

F2500 SADDLE ENTRY SETS

14"

10" 10"

14"

10" 10"

14"

10" 10"

14"

10" 10"

CS-F2500ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – No key cover. OR TS-F2500ML – Trim set only. No lock.

CS-F2500ML-DC – Complete set with mortise lock, cylinder and spindle. – Double cylinder. – No key cover. OR TS-F2500ML-DC – Trim set only. No lock.

CS-F2500ML-PF – Complete set with mortise lock and spindle. – Patio function. OR TS-F2500ML-PF – Trim set only. No lock.

CS-F2500ML-FD – Trim set only. – Full dummy.

3 5/

8"

2 7/

16"

3 5/

8"

2 7/

16"

5 3/

16"

5 3/

16"

Flush mount entry set. Plates DO NOT wrap door edge.Door template must be provided with door edge bevel. Requires 2 1/4” minimum door thickness.Specify manufacturer and function of lock to be used.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included.

Flush mount entry set. Plates DO NOT wrap door edge.Door template must be provided with door edge bevel.UC-F included in pricing.Requires 2 1/4” minimum door thickness.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Shown with 5” backset.

CS-F2500ML Single cylinder. Knob x knob or lever x lever entry set.

CS-F2500ML-DC Double cylinder. Knob x knob or lever x lever entry set.

CS-F2500ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-F2500ML-FD Full dummy. Knob x knob or lever x lever dummy set.

TS-F2500ML Single cylinder. Knob x knob or lever x lever entry set.

TS-F2500ML-DC Double cylinder. Knob x knob or lever x lever entry set.

TS-F2500ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-F2500ML–FD Full dummy. Knob x knob or lever x lever dummy set.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-4

Revised 05/02/16

999 CONTEMPORARY ENTRY SETSIllustrations are for demonstration purposes only. Available knob or lever high or low. Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Specify manufacturer and function of lock to be used.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Shown with 5” backset.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included.

9"9" 9"

9"

9" 9"

9"

9" 9"

9"

9" 9"

CS-999ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. OR TS-999ML – Trim set only. No lock.

CS-999ML-DC – Complete set with mortise lock, cylinder and spindle. – Double cylinder. – No key cover. OR TS-999ML-DC – Trim set only. No lock.

CS-999ML-PF – Complete set with mortise lock and spindle. – Patio function. OR TS-999ML-PF – Trim set only. No lock.

TS-999ML-FD – Trim set only. – Full dummy.

2 3/

4"

2 3/

4"

3 5/

8"

2 7/

16"

2 3/

4"2

7/16

"

2 3/

4"3

5/8"

2 3/

4"

CS-999ML Single cylinder. Knob x knob or lever x lever entry set.

CS-999ML-DC Double cylinder. Knob x knob or lever x lever entry set.

CS-999ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-999ML-FD Full dummy. Knob x knob or lever x lever dummy set.

TS-999ML Single cylinder. Knob x knob or lever x lever entry set.

TS-999ML-DC Double cylinder. Knob x knob or lever x lever entry set.

TS-999ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-999ML–FD Full dummy. Knob x knob or lever x lever dummy set.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-5

Revised 05/02/16

F999 CONTEMPORARY ENTRY SETSIllustrations are for demonstration purposes only. Available knob or lever high or low. Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.UC-F included in pricing.

Specify manufacturer and function of lock to be used.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob.

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Shown with 5” backset.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included.

CS-F999ML Single cylinder. Knob x knob or lever x lever entry set.

CS-F999ML-DC Double cylinder. Knob x knob or lever x lever entry set.

CS-F999ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-F999ML-FD Full dummy. Knob x knob or lever x lever dummy set.

TS-F999ML Single cylinder. Knob x knob or lever x lever entry set.

TS-F999ML-DC Double cylinder. Knob x knob or lever x lever entry set.

TS-F999ML-PF Patio function. Knob x knob or lever x lever entry set.

TS-F999ML–FD Full dummy. Knob x knob or lever x lever dummy set.

9"9" 9"

9"

9" 9"

9"

9" 9"

9"

9" 9"

CS-F999ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. OR TS-F999ML – Trim set only. No lock.

CS-F999ML-DC – Complete set with mortise lock, cylinder and spindle. – Double cylinder. – No key cover. OR TS-F999ML-DC – Trim set only. No lock.

CS-F999ML-PF – Complete set with mortise lock and spindle. – Patio function. OR TS-F999ML-PF – Trim set only. No lock.

TS-F999ML-FD – Trim set only. – Full dummy.

6 1/

4"

2 7/

16"

6 1/

4"

2 7/

16"

6 1/

4"

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-6

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Available for any door thickness.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all rim lock sets.Always specify lever/knob.

Specify which side of door (exterior or interior) the rim lock will be installed.

Complete rim lock sets with interior mortise lock and spindle.

RIM LOCK SETS

CS-RL300-PA – Complete rim lock with spindle. – Passage set.

4 1/2"7"

1 1/2"

CS-RL300-PR – Complete rim lock with spindle. – Privacy set.

4 1/2"

7"

1 1/2"

CS-RL300-BK – Complete rim lock with bit key. and spindle. – Privacy set.

4 1/2"

7"

1 1/2"

2 1/

16"

2 1/

16"

2 1/

16"2

1/4"

2 1/

4"

4"

7"

4"

7"

4"

7"

CS-RL300-PA Rim lock passage set.

CS-RL300-PR Rim lock privacy set.

CS-RL300-BK Rim lock bit key privacy set.

1 3/8"

7"

1/4"

PROFILE VIEW

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-7

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Available for any door thickness.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all rim lock sets.Always specify lever/knob.

Specify which side of door (exterior or interior) the rim lock will be installed.

Complete rim lock sets with interior mortise lock and spindle.

RIM LOCK SETS

CS-F-RL300-PA – Complete rim lock with spindle. – Passage set.

4 1/2"7"

1 1/2"

CS-F-RL300-PR – Complete rim lock with spindle. – Privacy set.

4 1/2"

7"

1 1/2"

CS-F-RL300-BK – Complete rim lock with bit key and spindle. – Privacy set.

4 1/2"

7"

1 1/2"

4 15

/16"

4 15

/16"

4 15

/16"2 1/

4"

2 1/

4"

4"

7"

4"

7"

4"

7"

CS-F-RL300-PA Rim lock passage set.

CS-F-RL300-PR Rim lock privacy set.

CS-F-RL300-BK Rim lock bit key privacy set.

1 3/8"

7"

1/4"

PROFILE VIEW

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-8

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Trim sets for tubular latch with spindle, no latch included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with tubular latch and spindle. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

926C CONTEMPORARY TUBULAR LATCH SETS w/CONCEALED SCREWS

CS-926C – Complete set with latch and spindle. OR TS-926C – Trim set only. No latch.

2 1/

2"

2 1/2" 2 1/2"

CS-926C Passage set w/concealed screws.

CS-926C-PR Privacy set w/concealed screws.

TS-926C Passage set w/concealed screws.

TS-926C-PR Privacy set w/concealed screws.

TS-926C-FD Full dummy w/concealed screws.

TS-926C-HD Half dummy w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-9

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

926C-8 CONTEMPORARY SECTIONAL INTERIOR MORTISE LOCK SETS w/CONCEALED SCREWS

Trim sets for interior mortise locks with spindle, no lock included. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with interior mortise lock and spindle. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

CS-926C-8IML – Complete passage set with interior mortise lock and spindle. OR TS-926C-8IML – Trim set only. No lock.

2 1/

2"

2 1/2" 2 1/2"

CS-926C-8x9497C-IML-PR – Complete privacy set with interior mortise lock and spindle. OR TS-926C-8x9497C-IML-PR – Trim set only. No lock.

2 1/

2"

2 1/

2"

1 3/4"3/4"

1/2"

11/1

6"

CS-926C-8IML Sectional interior mortise lock passage set w/concealed screws.

CS-926C-8x9497C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

TS-926C-8IML Sectional interior mortise lock passage set w/concealed screws.

TS-926C-8x9497C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-10

Revised 05/02/16

Illustrations are for demonstration purposes only. Any lever or knob may be substituted for lever or knob shown. Additional functions available.

F926C-8 CONTEMPORARY SECTIONAL INTERIOR MORTISE LOCK SETS w/CONCEALED SCREWS

Trim sets for interior mortise locks with spindle, no lock included. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with interior mortise lock and spindle. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

CS-F926C-8IML – Complete passage set with interior mortise lock and spindle. OR TS-F926C-8IML – Trim set only. No lock.

2 1/

2"

2 1/2" 2 1/2"

CS-F926C-8x9497C-IML-PR – Complete privacy set with interior mortise lock and spindle. OR TS-F926C-8x9497C-IML-PR – Trim set only. No lock.

2 1/

2"

2 1/

2"

1 3/4"3/4"

1/2" 11

/16"

2 1/2" 2 1/2"

CS-F926C-8IML Sectional interior mortise lock passage set w/concealed screws.

CS-F926C-8x9497C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

TS-F926C-8IML Sectional interior mortise lock passage set w/concealed screws.

TS-F926C-8x9497C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-11

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

ER13/9497C CONTEMPORARY AUXILIARY MORTISE BOLT SETS w/CONCEALED SCREWS

Trim sets for tubular mortise bolt, no mortise bolt included.

Complete sets with tubular mortise bolt.

CS-ER13/9497C-MB – Complete set with mortise bolt. OR TS-ER13/9497C-MB – Trim set only. No latch.

1 3/

4"

1/2"

1 3/4"3/4"

CS-9497C-MB – Complete set with mortise bolt. OR TS-9497C-MB – Trim set only. No latch.

1 3/

4"

1 3/4"

CS-ER13/9497C-MB Privacy bolt w/concealed screws.

CS-9497C-MB Privacy bolt w/concealed screws.

TS-ER13/9497C-MB Privacy bolt w/concealed screws.

TS-9497C-MB Privacy bolt w/concealed screws.

TS-ER13 Emergency release. No screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-12

Revised 05/02/16

926C CONTEMPORARY LEVER x KNOB SECTIONAL MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Compatible with Accurate mortise locks only.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*1 3/4” minimum door thickness.Thru-bolt only.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.Thru-bolt only.

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified. Refer to Section 6 pages 6-2 and 6-3 for cylinder trim options.

CS-926C-ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – Shown with CC-405ML-C. OR TS-926C-ML – Trim set only. No lock.

CS-926C-ML-DC – Complete set with mortise lock, cylinders and spindle. – Double cylinder. – Shown with CC-405ML-C. – Non-egress. OR TS-926C-ML-DC – Trim set only. No lock.

CS-926C-ML-PF – Complete set with mortise lock

and spindle. – Patio function. OR TS-926C-ML-PF – Trim set only. No lock.

TS-926C-ML-FD – Trim set only. – Full dummy.

1 3/4"

2 1/2"

2 1/

2"

2 1/2"2 1/2"

2 1/

2"

2 1/

2"

2 1/

2"

1 3/4"

2 7/

16"

2 7/

16"

3 5/

8"

3 5/

8"

1 3/4" 1 3/4" 1 3/4"

CS-926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

CS-926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

CS-926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

TS-926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

TS-926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-13

Revised 05/02/16

F926C CONTEMPORARY LEVER x KNOB SECTIONAL MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Compatible with Accurate mortise locks only.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*1 3/4” minimum door thickness.Thru-bolt only.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.Thru-bolt only. UC-F built into pricing.

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified. Refer to Section 6 pages 6-2 and 6-3 for cylinder trim options.

CS-F926C-ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – Shown with CC-405ML-C. OR TS-F926C-ML – Trim set only. No lock.

CS-F926C-ML-DC – Complete set with mortise lock, cylinders and spindle. – Double cylinder. – Shown with CC-405ML-C. – Non-egress. OR TS-F926C-ML-DC – Trim set only. No lock.

CS-F926C-ML-PF – Complete set with mortise lock

and spindle. – Patio function. OR TS-F926C-ML-PF – Trim set only. No lock.

TS-F926C-ML-FD – Trim set only. – Full dummy.

1 3/4"

2 1/2"

2 1/

2"

2 1/2"2 1/2"

2 1/

2"

2 1/

2"

2 1/

2"

1 3/4"

2 7/

16"

2 7/

16"

3 5/

8"

3 5/

8"

1 3/4" 1 3/4" 1 3/4"

CS-F926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

CS-F926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

CS-F926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

TS-F926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

TS-F926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-14

Revised 05/02/16

RP926C CONTEMPORARY TUBULAR LATCH SETS w/CONCEALED SCREWS

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Trim sets for tubular latch with spindle, no latch included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with tubular latch and spindle. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

CS-RP926C – Complete set with latch and spindle. OR TS-RP926C – Trim set only. No latch.

2 1/

2"

2 1/2" 2 1/2"

CS-RP926C Passage set w/concealed screws.

CS-RP926C-PR Privacy set w/concealed screws.

TS-RP926C Passage set w/concealed screws.

TS-RP926C-PR Privacy set w/concealed screws.

TS-RP926C-FD Full dummy w/concealed screws.

TS-RP926C-HD Half dummy w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-15

Revised 05/02/16

RP926C-8 CONTEMPORARY SECTIONAL INTERIOR MORTISE LOCK SETS w/CONCEALED SCREWS

CS-RP926C-8IML – Complete passage set with interior mortise lock and spindle. OR TS-RP926C-8IML – Trim set only. No lock.

2 1/

2"

2 1/2" 2 1/2"

CS-RP926C-8xRP9499C-IML-PR – Complete privacy set with interior mortise lock and spindle. OR TS-RP926C-8xRP9499C-IML-PR – Trim set only. No lock.

2 1/

2"

2 1/

2"

1 3/4"5/8"

11/1

6"

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Trim sets for interior mortise locks with spindle, no lock included. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with interior mortise lock and spindle. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

CS-RP926C-8IML Sectional interior mortise lock passage set w/concealed screws.

CS-RP926C-8xRP9499C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

TS-RP926C-8IML Sectional interior mortise lock passage set w/concealed screws.

TS-RP926C-8xRP9499C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-16

Revised 05/02/16

F-RP926C-8 CONTEMPORARY SECTIONAL INTERIOR MORTISE LOCK SETS w/CONCEALED SCREWS

Trim sets for interior mortise locks with spindle, no lock included. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Complete sets with interior mortise lock and spindle. 2 7/8” center-to-center. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

CS-F-RP926C-8IML – Complete passage set with interior mortise lock and spindle. OR TS-F-RP926C-8IML – Trim set only. No lock.

2 1/

2"

2 1/2" 2 1/2"

CS-F-RP926C-8xRP9499C-IML-PR – Complete privacy set with interior mortise lock and spindle. OR TS-F-RP926C-8xRP9499C-IML-PR – Trim set only. No lock.

2 1/

2"

2 1/

2"

1 3/4"5/8"

11/1

6"

2 1/2" 2 1/2"

TS-F-RP926C-8IML Sectional interior mortise lock passage set w/concealed screws.

TS-F-RP926C-8xRP9499C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

CS-F-RP926C-8IML Sectional interior mortise lock passage set w/concealed screws.

CS-F-RP926C-8xRP9499C-IML-PR Sectional interior mortise lock privacy set w/concealed screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-17

Revised 05/02/16

ER12/RP9499C CONTEMPORARY AUXILIARY MORTISE BOLT SETS w/CONCEALED SCREWS

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

Trim sets for tubular mortise bolt, no mortise bolt included.

Complete sets with tubular mortise bolt.

CS-ER12/RP9499C-MB – Complete set with mortise bolt. OR TS-ER12/RP9499C-MB – Trim set only. No latch.

1 3/

4"

1 3/4"5/8"

CS-RP9499C-MB – Complete set with mortise bolt. OR TS-RP9499C-MB – Trim set only. No latch.

1 3/

4"

1 3/4"

CS-ER12/RP9499C-MB Privacy bolt w/concealed screws.

CS-RP9499C-MB Privacy bolt w/concealed screws.

TS-ER12/RP9499C-MB Privacy bolt w/concealed screws.

TS-RP9499C-MB Privacy bolt w/concealed screws.

TS-ER12 Emergency release. No screws.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-18

Revised 05/02/16

RP926C CONTEMPORARY LEVER x KNOB SECTIONAL MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Compatible with Accurate mortise locks only.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*1 3/4” minimum door thickness.Thru-bolt only.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.Thru-bolt only.

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified. Refer to Section 6 pages 6-2 and 6-3 for cylinder trim options.

CS-RP926C-ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – Shown with CC-401ML-C. OR TS-RP926C-ML – Trim set only. No lock.

CS-RP926C-ML-DC – Complete set with mortise lock, cylinders and spindle. – Double cylinder. – Shown with CC-401ML-C. – Non-egress. OR TS-RP926C-ML-DC – Trim set only. No lock.

CS-RP926C-ML-PF – Complete set with mortise lock

and spindle. – Patio function. OR TS-RP926C-ML-PF – Trim set only. No lock.

TS-RP926C-ML-FD – Trim set only. – Full dummy.

1 3/4"

2 1/2"

2 1/

2"

2 1/2"2 1/2"

2 1/

2"

2 1/

2"

2 1/

2"

1 3/4"

2 7/

16"

2 7/

16"

3 5/

8"

3 5/

8"

1 3/4" 1 3/4" 1 3/4"

CS-RP926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

CS-RP926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

CS-RP926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-RP926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

TS-RP926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-RP926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

TS-RP926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-RP926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-19

Revised 05/02/16

F-RP926C CONTEMPORARY LEVER x KNOB SECTIONAL MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress). Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

Compatible with Accurate mortise locks only.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*1 3/4” minimum door thickness.Thru-bolt only.

Trim sets for mortise lock with spindle, no lock or cylinder(s) included. Escutcheon is 7/16” thick. Escutcheon with 3/16” lever hub is 5/8”.

2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.Thru-bolt only. UC-F built into pricing.

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified. Refer to Section 6 pages 6-2 and 6-3 for cylinder trim options.

CS-F-RP926C-ML – Complete set with mortise lock, cylinder and spindle. – Single cylinder. – Shown with CC-401ML-C. OR TS-F-RP926C-ML – Trim set only. No lock.

CS-F-RP926C-ML-DC – Complete set with mortise lock, cylinders and spindle. – Double cylinder. – Shown with CC-401ML-C. – Non-egress. OR TS-F-RP926C-ML-DC – Trim set only. No lock.

CS-F-RP926C-ML-PF – Complete set with mortise lock

and spindle. – Patio function. OR TS-F-RP926C-ML-PF – Trim set only. No lock.

TS-F-RP926C-ML-FD – Trim set only. – Full dummy.

1 3/4"

2 1/2"

2 1/

2"

2 1/2"2 1/2"

2 1/

2"

2 1/

2"

2 1/

2"

1 3/4"

2 7/

16"

2 7/

16"

3 5/

8"

3 5/

8"

1 3/4" 1 3/4" 1 3/4"

CS-F-RP926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

CS-F-RP926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

CS-F-RP926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F-RP926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

TS-F-RP926C-ML Single cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F-RP926C-ML-DC Double cylinder. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional. Non-egress.

TS-F-RP926C-ML-PF Patio function. Lever/knob x lever/knob ML entry set w/concealed screws. Sectional.

TS-F-RP926C-ML-FD Full dummy. Lever/knob x lever/knob ML dummy set w/concealed screws. Sectional.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-20

Revised 05/02/16

Illustrations are for demonstration purposes only. Any lever or knob may be substituted for lever or knob shown. Additional functions available.

M100-ML MINIMALIST LEVER x KNOB MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress).

Warning: This is a difficult installation. All mortising should be done by door shop to Sun Valley Bronze specs. 1 3/4” thick minimum door thickness. 1 1/2” wide ML face plate.

Complete sets with mortise lock and spindle. Thread in knob/lever hub 7/32” projection.Knob/lever and turn piece thread into a brass block, machined and fastened to ML lock body by Sun Valley Bronze.2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.

Component Pricing:Lever/Knob w/Threaded Hub TPC w/threaded Hub IML Lock Body Machined w/Brass Blocks to Receive Knob/Lever Threaded Hubs IML Lock Body Machined w/Brass Block to Receive Threaded TPC HubSee Locks, Parts & Upcharges Section for ML pricing.

1 3/4"

CS-M100-ML – Complete set with mortise lock, cylinder, and spindle. – Single cylinder. – Shown w/CC-400ML-C.

3 5/

8"

2 7/

16"

5/8"1 3/4"

CS-M100-ML-DC – Complete set with mortise lock, cylinder, and spindle. – Double cylinder. – Shown w/CC-400ML-C.

3 5/

8"

1 3/4"

CS-M100-ML-PF – Complete set with mortise lock and spindle. – Patio function.

2 7/

16"

5/8"

1 1/8" 1 1/8"1 1/8" 1 1/8" 1 1/8" 1 1/8"

5/32

"

1 1/8"

Screw in Lever/Knob Hub – Side view.

15/16"

CS-M100-ML Single cylinder. Lever/knob x lever/knob mortise lock entry set.

CS-M100-ML-DC Double cylinder. Lever/knob x lever/knob mortise lock entry set. Sectional. Non-egress.

CS-M100-ML-PF Patio function. Lever/knob x lever/knob mortise lock entry set.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-21

Revised 05/02/16

Illustrations are for demonstration purposes only. Any lever or knob may be substituted for lever or knob shown. Additional functions available.

F-M100-ML MINIMALIST LEVER x KNOB MORTISE LOCK ENTRY SETS

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress).

Warning: This is a difficult installation. All mortising should be done by door shop to Sun Valley Bronze specs. 1 3/4” thick minimum door thickness. 1 1/2” wide ML face plate.

Complete sets with mortise lock and spindle. Thread in knob/lever hub 7/32” projection.Knob/lever and turn piece thread into a brass block, machined and fastened to ML lock body by Sun Valley Bronze.2 1/2” or 2 3/4” backset standard.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob mortise lock entry sets.Always specify lever/knob design and ML cylinder trim.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.

Component Pricing:Lever/Knob w/Threaded Hub TPC w/threaded Hub IML Lock Body Machined w/Brass Blocks to Receive Knob/Lever Threaded Hubs IML Lock Body Machined w/Brass Block to Receive Threaded TPC HubSee Locks, Parts & Upcharges Section for ML pricing.

1 3/4"

CS-F-M100-ML – Complete set with mortise lock, cylinder, and spindle. – Single cylinder. – Shown w/CC-400ML-C.

3 5/

8"

2 7/

16"

5/8"1 3/4"

CS-F-M100-ML-DC – Complete set with mortise lock, cylinder, and spindle. – Double cylinder. – Shown w/CC-400ML-C.

3 5/

8"1 3/4"

CS-F-M100-ML-PF – Complete set with mortise lock and spindle. – Patio function.

2 7/

16"

5/8"

1 1/8"1 1/8" 1 1/8"1 1/8" 1 1/8" 1 1/8"

5/32

"

1 1/8"

Screw in Lever/Knob Hub – Side view.

15/16"

CS-F-M100-ML Single cylinder. Lever/knob x lever/knob mortise lock entry set.

CS-F-M100-ML-DC Double cylinder. Lever/knob x lever/knob mortise lock entry set. Sectional. Non-egress.

CS-F-M100-ML-PF Patio function. Lever/knob x lever/knob mortise lock entry set.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-22

Revised 05/02/16

Illustrations are for demonstration purposes only. Any lever or knob may be substituted for lever or knob shown. Additional functions available.

M100-IML MINIMALIST INTERIOR MORTISE SETS

Complete sets with interior mortise lock and spindle. 2 1/4” center-to-center.

Warning: This is a difficult installation. All mortising should be done by door shop to Sun Valley Bronze specs. 1 3/4” thick minimum door thickness. 1 1/2” wide IML face plate.

Complete sets with interior mortise lock and spindle. Thread in knob/lever hub 7/32” projection.Knob/lever and turn piece thread into a brass block, machined and fastened to IML lock body by Sun Valley Bronze.2 1/2” or 2 3/4” backset standard.Custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob interior mortise lock sets.Always specify lever/knob design.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.

Component Pricing:Lever/Knob w/Threaded Hub TPC w/threaded Hub IML Lock Body Machined w/Brass Blocks to Receive Knob/Lever Threaded Hubs IML Lock Body Machined w/Brass Block to Receive Threaded TPC HubSee Locks, Parts & Upcharges Section for IML pricing.

CS-M100-IML Lever/knob x lever/knob interior mortise lock passage set.

CS-M100-IML-PR Lever/knob x lever/knob interior mortise lock privacy set.

CS-M100-IML – Complete passage set. – 1 1/2" wide face plate interior

mortise lock and spindle.

1 1/

8"1 1/8"

2 1/

4"

5/8"5/8"

CS-M100-IML-PR – Complete privacy set. – 1 1/2" wide face plate interior

mortise lock and spindle.

1 1/8"

1 1/8" 1 1/8"

5/32

"

1 1/8"

Screw in Lever/Knob Hub – Side view.

15/16"

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-23

Revised 05/02/16

Illustrations are for demonstration purposes only. Any lever or knob may be substituted for lever or knob shown. Additional functions available.

F-M100-IML MINIMALIST INTERIOR MORTISE SETS

Complete sets with interior mortise lock and spindle. 2 1/4” center-to-center.

Warning: This is a difficult installation. All mortising should be done by door shop to Sun Valley Bronze specs. 1 3/4” thick minimum door thickness. 1 1/2” wide IML face plate.

Complete sets with interior mortise lock and spindle. Thread in knob/lever hub 7/32” projection.Knob/lever and turn piece thread into a brass block, machined and fastened to IML lock body by Sun Valley Bronze.2 1/2” or 2 3/4” backset standard.Custom backsets available. Call for options and pricing.Door handing and thickness is required for all lever/knob interior mortise lock sets.Always specify lever/knob design.*Upcharge for doors over 2 1/4” thick.**1 3/4” minimum door thickness.

Component Pricing:Lever/Knob w/Threaded Hub TPC w/threaded Hub IML Lock Body Machined w/Brass Blocks to Receive Knob/Lever Threaded Hubs IML Lock Body Machined w/Brass Block to Receive Threaded TPC HubSee Locks, Parts & Upcharges Section for IML pricing.

CS-F-M100-IML Lever/knob x lever/knob interior mortise lock passage set.CS-F-M100-IML-PR Lever/knob x lever/knob interior mortise lock privacy set.

CS-F-M100-IML – Complete passage set. – 1 1/2" wide face plate interior

mortise lock and spindle.

2 1/

4"

5/8"5/8"

CS-F-M100-IML-PR – Complete privacy set. – 1 1/2" wide face plate interior

mortise lock and spindle.

5/32

"

1 1/8"

Screw in Lever/Knob Hub – Side view.

15/16"

1 1/8"1

1/8"

1 1/8" 1 1/8" 1 1/8"

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-24

Revised 05/02/16

2000 MINIMALIST HANDLE ENTRY SETSIllustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate. Additional functions available.

Requires 2 1/4” minimum door thickness.Additional functions and custom backsets available. Call for options and pricing.Door handing and thickness is required for all handle entry sets.*Upcharge for doors over 2 1/4” thick. Refer to Parts, Miscellaneous Upcharges UC-2 through UC-4.

Complete sets with cylinder(s), spindle and emergency egress mortise lock (except where noted non-egress).

1 3/4"

1"

13 5

/8"

15 1

/8"

CS-2000HH (No Escutcheon Plate) – Complete set with mortise lock and cylinder. – Single cylinder. – No key cover. – Double grip handle. – Shown w/std GH-983.

1"

1 3/4"

15 3

/4"

17 1

/4"

CS-2001HH (No Escutcheon Plate) – Complete set with mortise lock and cylinder. – Single cylinder. – No key cover. – Double grip handle. – Shown w/std GH-993.

10"

1 1/4" 1 1/4"

8"

4 1/

8"

4 1/

8"

3 5/

8"

3 5/

8"

CS-2000HH Single cylinder. Handle x handle.

CS-2000HH-DC Double cylinder. Handle x handle. Non-egress. (Not shown)

TS-2000HH-FD Full dummy. Back-to-back grip handles. No thumb latch, key cover or turn piece. (Not shown)

CS-2001HH Single cylinder. Handle x handle.

CS-2001HH-DC Double cylinder. Handle x handle. Non-egress. (Not shown)

TS-2001HH-FD Full dummy. Back-to-back grip handles. No thumb latch, key cover or turn piece. (Not shown)

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-25

Revised 05/02/16

THE LIFT LEVERIllustrations are for demonstration purposes only.

The Lift lever. Specify left or right hand.

1 1/4” Break off screws included.

L-176LSQ-RH – The Lift lever. – Specify L-176LSQ-RH (right hand) or L-176LSQ-LH (left hand). – Right hand shown.

1" 4 5/8"

1 1/

8"

5 5/8"1"

1"

2 3/4"

1 1/4"1 1/8"

Side View

Front View

Top View

L-176LSQ-RH The Lift Lever* Square hub. Right hand (shown).

L-176LSQ-LH The Lift Lever* Square hub. Left hand.

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-26

Revised 05/02/16

Illustrations are for demonstration purposes only.

THE LIFT TURN PIECE & TURN PIECE ESCUTCHEON

The Lift turn piece and escutcheon.

1 1/4” Break off screws included.

TPC-L1 The Lift turn piece.

MB-L12 The Lift turn piece escutcheon.

L12MB w/ TPC-L1 – Turn piece w/escutcheon.

2 1/

32"

1 1/32" 1"

1 3/

32"

3/8"

11/1

6"

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-27

Revised 05/02/16

Illustrations are for demonstration purposes only.

P-L13 THE LIFT INTERIOR MORTISE LOCK PASSAGE SETS

Complete sets with interior mortise lock and spindle.

Trim sets for interior mortise locks with spindle, no lock included.

1 1/4” Break off screws included.

CS-L13IML – Complete passage set w/interior

mortise lock and spindle. – Shown w/L-176LSQ levers.

OR TS-L13IML – Trim set only. No lock.

3"1 3/4"

1"

5/16

"

1 3/4"

1"

5/16

"

CS-L13IML-PR – Complete privacy set w/interior

mortise lock and spindle. – Shown w/L-176LSQ levers and MB-L12

w/TPC-L1. OR

TS-L13IML-PR – Trim set only. No lock.

3"1"

5/16

"

1 3/4"

1"

5/16

"

1 1/32"

CS-L13IML Complete passage set shown w/L-176LSQ levers. P-L13 (ext) P-L13 (int)

CS-L13IML-PR Complete privacy set shown w/L-176LSQ levers and MB-L12 w/TPC-L1. P-L13 (ext) P-L13 (int)

TS-L13IML Passage set shown w/L-176LSQ levers. Trim only. P-L13 (ext) P-L13 (int)

TS-L13IML-PR Privacy set shown w/L-176LSQ levers and MB-L12 w/TPC-L1. Trim only. P-L13 (ext) P-L13 (int)

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-28

Revised 05/02/16

Illustrations are for demonstration purposes only.

P-L16 THE LIFT INTERIOR MORTISE LOCK PASSAGE & PRIVACY SETS

Complete sets with interior mortise lock and spindle.

Trim sets for interior mortise locks with spindle, no lock included.

1 1/4” Break off screws included.

1 3/4"

6"

5/16

"

1"

CS-L16IML – Complete passage set w/interior

mortise lock and spindle. – Shown w/L-176LSQ levers.

OR TS-L16IML – Trim set only. No lock.

CS-L16IML-PR – Complete privacy set w/interior

mortise lock and spindle. – Shown w/L-176LSQ levers and TPC-L1.

OR TS-L16IML-PR – Trim set only. No lock.

1 3/4"

5/16

"

1"

1 3/4"

6"

5/16

"

1"

1 3/4"

5/16

"

1"

CS-L16IML Complete passage set shown w/L-176LSQ levers. P-L16 (ext) P-L16 (int)CS-L16IML-PR Complete privacy set shown w/L-176LSQ levers and TPC-L1. P-L16 (ext) P-L16 (int)

TS-L16IML Passage set shown w/L-176LSQ levers. Trim only. P-L16 (ext) P-L16 (int)

TS-L16IML-PR Privacy set shown w/L-176LSQ levers and TPC-L1. Trim only. P-L16 (ext) P-L16 (int)

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-29

Revised 05/02/16

L-13 THE LIFT TUBULAR LATCH PASSAGE SETSIllustrations are for demonstration purposes only.

Complete sets with tubular latch and spindle.

Trim sets for tubular latch with spindle, no latch included.

1 1/4” Break off screws included.

CS-L13 – Complete passage set w/latch

and spindle. – Shown w/L-176LSQ levers.

OR TS-L13 – Trim set only. No lock.

3"

1 3/4"

1"

5/16

"

1 3/4"

1"

5/16

"

CS-L13 Complete passage set shown w/L-176LSQ levers. P-L13 (ext) P-L13 (int)

TS-L13 Passage set shown w/L-176LSQ levers. Trim only. P-L13 (ext) P-L13 (int)

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-30

Revised 05/02/16

Illustrations are for demonstration purposes only.

L-16 THE LIFT TUBULAR LATCH PASSAGE SETS

Complete sets with tubular latch and spindle.

Trim sets for tubular latch with spindle, no latch included.

1 1/4” Break off screws included.

1 3/4"

6"

1"

CS-L16 – Complete passage set w/latch

and spindle. – Shown w/L-176LSQ levers.

OR TS-L16 – Trim set only. No lock.

1 3/4"

5/16

"

1"

5/16

"

CS-L16 Complete passage set shown w/L-176LSQ levers. P-L16 (ext) P-L16 (int)

TS-L16 Passage set shown w/L-176LSQ levers. Trim only. P-L16 (ext) P-L16 (int)

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

29-31

Revised 05/02/16

Illustrations are for demonstration purposes only. Any Sun Valley Bronze lever or knob may be specified.

2 3/4” backset only.Door handing and thickness is required.Always specify lever design.

Complete hotel entry set with internal locking system, card reader and strike.

HOTEL ENTRY SETS

HCR-1000 – Complete set with internal locking system, card reader and strike. – Software and programming equipment available from Saflock.

3 5/8"

10 1

/2"

1 1/16"3 5/8"

2 7/

8"

2 7/

8"

2 7/

8"

CS-HCR1000 Card reader entry set.

TS-HCR1000 Card reader trim set.