SPARE PARTS / Bebop 2 / Central body - Pennekamp
Transcript of SPARE PARTS / Bebop 2 / Central body - Pennekamp
3
Put the camera support in place and secure it with the 2 MCFAS00197 screws in the front.
4 Secure the back of the camera support with the 2 MCFAS00221 screws.
1 Slide the nose of the Bebop 2 back on.*
Caution: make sure you do not damage the GPS during the process.
SPARE PARTS / Bebop 2 / Central body
To replace the central body under the Bebop 2, you need a T5 screwdriver, a T6 screwdriver, pliers and a box cutter.
It is recommended to use the Parrot Toolbox for this operation.
REFERENCES: Red Central Body: PF070226AB / White Central Body: PF070203AB
2 Slide the nose forward to remove it.*
Caution: make sure you do not damage the GPS during the process.
1 Put the cross back on the drone.
4 With a box cutter, peel off the sticker.
x6
1 Remove the 2 screws holding the nose.
2 Secure the nose with the 2 screws.
2 Disconnect the GPS from the flex.
1 Connect the GPS to the flex.
2 Remove the camera support and all its elements.
2
Put the lock on top of the connector. Make sure the screw holes are aligned.
G207
G207
1REMOVING
THE NOSE
14INSTALLING
THE NOSE
2REMOVING
THE GPS
13INSTALLING
THE GPS
3REMOVING
THE CAMERA
12INSTALLING
THE CAMERA
1 Remove the 2 MCFAS00197 and the 2 MCFAS00221 screws.
1 Fix the connector of the camera support on the motherboard.
1 Remove the 3 screws holding the GPS to the support of the camera.
2 Secure the GPS with 3 new MCFAS00220 screws.
1 Remove the 4 screws holding the foot and remove the old foot.
1 Connect the cables to each connector.
3 Remove cable from the antenna.
3 Fix the antenna back to the cable.
2 Slide the antenna off the foot.
2 Secure each connector with 2 MCFAS00333 screws.
5 Disconnect the antennas of the front feet.
5 Put each foot back into place and secure them with 4 screws.
4
10
REMOVING
THE FRONT FEET
INSTALLING
THE FRONT FEET
5
11
REMOVING
THE REAR FEET
INSTALLING
THE REAR FEET
REMOVING THE
CAMERA AND THE FAN
UNDER THE DRONE
1 Use a T5 screwdriver to remove the 4 screws holding the foot.
1 Connect the cables to each connector.
1 Use the pliers to remove the metal stems of the old motherboard.
5 Disconnect the cables of the fan and remove it completely.
4 Slightly pull on the cable to disconnect them from each connector.
4 Slide the antenna in the foot.
2 Remove the foot and use a T6 screwdriver to remove the 2 screws holding the connector.
2 Secure each connector with 2 MCFAS00333 screws.
2 Use a T5 screwdriver to remove the 3 screws holding the fan.
6 Disconnect the connector of the camera and remove it completely.
3 Slightly pull on the cable to disconnect it from the connector.
3 Put each foot back into place and secure them with 4 screws.
3 Use a T5 screwdriver to remove the 2 screws holding the camera.
2 Connect the fan to the motherboard.
5 Secure the fan with the 3 MCFAS00197 screws .
6 Use the pliers to screw the metal stems on the new motherboard.
3 With a box cutter, peel off the sticker. Put the sticker back into place.
1 Use a T5 screwdriver to remove the 2 screws holding the camera.
4 Secure the camera with the 2 MCFAS00199 screws.
AA
CC
AA C C
1 Use the pliers to unscrew the 4 washers under the drone.
3 Secure the cross with the washers. 2 Make sure to correctly put back all the cables.
2 Remove the cross.
REMOVING
THE CROSS
INSTALLING
THE CROSS
6
9
7
Package content:1 central body / 6 screws
INSTALLING THE
ELEMENTS ON THE
NEW CENTRAL BODY8
* Using a new nose part will ease the process and prevent from damaging the GPS.
D I F F I C U L T Y L E V E L