Note: In addition to the above dimensions, allow three feet of space on all sides for consumable replenishment,paper jam removal, and maintenance and service procedures. Images may not be to scale.

MX-MF11

MX-RB14 MX-LC13 MX-LC13

MX-FN22MX-FD10MX-ST10MX-CF11MX-RB15

A B C D E F G H JI K

L

MX-RB12

M Height from platen glass with document feeder open

A 4-3/4" B 30-1/4" C 13-1/4" D, E 36" F 6-1/2" G 8-3/8" H 34-3/8" I 18" J, K 35-1/4" L 240-1/4" M 23"

SPACE REQUIREMENTS AND PLANNING GUIDE

MX-6500N/7500N

Installing Dealer

Read this document in its entirety before planning your configuration.Plan ahead and make sure your installation is a great success! Remember to check the latest information on these products and make sure that the following items are available prior to installation.

• Verifydedicatedpowersourceandcheckforstability.TheMX-6500N/7500NDocumentSystemsrequirea208-240VAC,60Hz,20Amp power source.

The MX-6500N/7500N main unit requires one 208-240 VAC, 20 Amp power source plug

The MX-BM50, MX-FN21, MX-FN22, MX-LC13, and MX-ST10 options each require separate 120 VAC, 15 Amp power source plugs.

• Confirmthatyouhavethelatestfirmwareavailablefrom www.sharp-pcservice.comtoupgradeyourMX-6500N/7500N Document Systems.

•Someaccessoriesrequireaproductkeyforoperation.YoushouldobtaintheaccessoryApplicationCodeandmachine’sserialnumbertoregistertheproductkey online prior to arrival at the customer location.

•ChecktoseeifMySharp™onlinetrainingisset upfortheend-user.

•Verifythatthecustomerhasenoughsupplieson-handtocomplete alargerushjob.After-hoursprintingand/orholidayworkmaytake placefollowinganinstallation.SeeSupplies&Accessoriesliston the following page.

* Illustrations shown are for measurement purposes only and may not be to scale. For configurations see subsequent pages.

Design and specifications are subject to change without notice. All product dimensions listed are approximate. Sharp, Sharp OSA, My Sharp and all related trademarks are trademarks or registered trademarks of Sharp Corporation and/or its affiliated companies. PCL is a registered trademark of HP Company. Adobe and PostScript are registered trademarks of Adobe Systems Inc. All other trademarks are the property of their respective owners.

31 1/8"

48 7/8"

25 7/8"

14 3/4"

8 3/8"

MX-FN21 MX-RB15MX-LC12

MX-LCX3N

64 1/2"

48 7/8" 26 3/8"

MX-SL10N

MX-MF10

MX-GBCX2

GBC Plockmatic

MX-FD50

MX-XB50

MX-TM50 MX-BM50 MX-CF50

Exit Trayincluded withMX-BM50

87 1/4"

78"

23 3/4" 35 1/2"

39"

3"

14" 14"16 3/4"

Width Measurements

Depth Measurements (overhead view).*

Base Unit Measurements Shown with MX-FN21, MX-RB13, MX-MF10, MX-LC12, and MX-LCX3N.*

Measurements for GBC SmartPunch™ Pro and Plockmatic Booklet Maker System.*

© 2013SharpElectronicsCorporation.Allrightsreserved.10/13

B

A

B

A

Configuration AThese configurations require the MX-MF10.• The MX-TR14 and MX-LT10 are not required. • The MX-LC12 cannot be used with the MX-LCX3N. • These items cannot be combined with items from paper feed configuration B.

Configuration BThis configuration requires the MX-RB14 and MX-LC13. • An MX-RB17 is required to connect two MX-LC13 Large Capacity Trays. • The MX-MF11 can also be added to the first MX-LC13 but cannot be used alone. • These items cannot be combined with items from paper feed configuration A.

MX-6500N/7500N

1. Base Unit

MX-MF10*Multi Bypass Tray

and and/or and/or or

MX-RB14Paper Pass Unit

* The MX-MF10 is required as a minimum configuration if the MX-RB14 is not selected. MX-LC13

Large Capacity Tray (2 Drawers; Ledger)

MX-LC13Large Capacity Tray (2 Drawers; Ledger)(not required)

MX-RB17LCT ConnectingKit (required for2nd MX-LC13)

3. MX-LC13

MX-MF11500-sheetMulti Bypass Tray (not required)

MX-TR14Right SideExit Tray

MX-LT10Long PaperFeeding Tray

MX-LC12 Large Capacity Cassette(Letter)

MX-LCX3N Large Capacity Cassette(Ledger)

2. MX-LC12 5. MX-MF10 6. MX-MF114. MX-LCX3N

and and and

and

MX-6500N/7500N Configuration Chart

StEP 1: ChooSE PaPEr fEED Configuration

Supported Paper Weights

1. BaseUnit(3,000Sheets) UpperDrawer(tandem):16lb.Bondto28lb.Bond(60-105gsm) Middle/LowerDrawer:16lb.Bondto100lb.Bristol(60-220gsm)

2. MX-LC12(3,500Sheets) 16lb.Bondto100lb.Bristol(60-220gsm)

3. MX-LC13(5,000Sheets) Upper/LowerDrawer:15lb.Bondto110lb.Cover(55-300gsm)

4. MX-LCX3N(3,000Sheets)

16lb.Bondto100lb.Bristol(60-220gsm)

5. MX-MF10(100Sheets) 15lb.Bondto110lb.Cover(55-300gsm)

6. MX-MF11(500Sheets) 15lb.Bondto100lb.Bristol(55-220gsm)

Supplies & Accessories

•BlackTonerCartridge MX-62NTBA•CyanTonerCartridge MX-75NTCA•MagentaTonerCartridge MX-75NTMA•YellowTonerCartridge MX-75NTYA•BlackDeveloper MX-62NVBA •Cyan/Magenta/YellowDeveloper MX-62NVSA

•Drum MX-62NRSA•TonerCollectionContainer MX-700HB•120V/15APowerFilter AR-D5133NT (forMX-BM50,MX-FN21,MX-FN22, MX-LC13andMX-ST10)

•208-240V/20APowerFilter MX-E524ZNT (forMX-6500N/7500N)

© 2013SharpElectronicsCorporation.Allrightsreserved.

C

B

MX-FN22 Saddle Stitch Finisher 4K (100-sheet staple)

MX-FN21 Finisher 4K (100-sheet staple)

MX-PCB50 PlockmaticInterface Kit

MX-ST10High CapacityStacker

MX-RB15Curl CorrectionUnit

MX-RB12Paper PassUnitand and/or

and and or

B

Configuration B: High Capacity StackingThis configuration requires the MX-RB12, MX-RB15 and one MX-ST10. • An additional MX-ST10 can be added, but is not required. • Each MX-ST10 includes one MX-CA10 Paper Cart. • Additional paper carts can be ordered for convenience. • The MX-SL10N Status Indicator can be added to any configuration.

C

Configuration C: Basic 100-sheet Staple FinishingThis configuration requires the MX-RB12, MX-RB15 and the MX-FN21 or MX-FN22.• The MX-FN21 cannot be used with the MX-FN22. • The MX-BM50 requires the MX-FN21 and MX-PCB50. • The MX-FD50 must be connected to the MX-TM50. • The MX-SL10N Status Indicator can be added to any configuration.

MX-TM10 Trimming Unit

MX-PN13B3-Hole Punch Unit

MX-ST10High CapacityStacker(not required)

MX-CF112-Tray Inserter Unit

MX-6500N/7500N + MX-RB12 Paper Pass Unit + MX-RB15 Curl Correction Unit (both required for Configurations B and C)

MX-SL10N Status Indicator(optional)

A

MX-6500N/7500N MX-TU14Center Exit Tray

A

Configuration AThe MX-TU14 must be installed if no finishing options are selected. This item cannot be combined with items from other finishing configurations.

MX-BM50Booklet Maker

MX-CF50 Cover Feeder

Exit Tray Includedwith MX-BM50

MX-TM50Trimming UnitModule

MX-XB50Rail Unit (recommended)

MX-FD50Square Spine Module

and and

and

and

Plockmatic Production Booklet Maker System

MX-6500N/7500N Configuration Chart

StEP 2: ChooSE finiShing Configuration

© 2013SharpElectronicsCorporation.Allrightsreserved.

D

MX-ST10High CapacityStacker

MX-GBCX2GBC SmartPunch ProTM

MX-RB13Relay Unit

D

Configuration D: Advanced 100-sheet Staple FinishingThis configuration requires the MX-RB12, MX-RB15 and the MX-FN21 or MX-FN22.• The MX-CF11, both MX-ST10s, MX-GBCX2, MX-FD10, and Plockmatic Production Booklet Maker System are all optional.• The MX-GBCX2 requires the MX-RB13 (The MX-RB13 is only required when using the MX-GBCX2).• The MX-RB13 is required to connect a 100-sheet finisher and 2-Tray Inserter Unit directly.• The MX-FN21 cannot be used with the MX-FN22.• The MX-BM50 requires the MX-FN21 and MX-PCB50.• The MX-FD50 must be connected to the MX-TM50.• The MX-SL10N Status Indicator can be added to any configuration.

MX-ST10High CapacityStacker

MX-CF112-Tray Inserter Unit

and/orandand and/orand/or

MX-FD10 Multi-Folding Unit

(continued)

MX-FN22 Saddle Stitch Finisher 4K (100-sheet staple)

MX-FN21 Finisher 4K (100-sheet staple)

andand or

MX-TM10 Trimming Unit

MX-PN13B3-Hole Punch Unit

MX-6500N/7500N + MX-RB12 Paper Pass Unit + MX-RB15 Curl Correction Unit (both required for Configuration D)

MX-RB15Curl CorrectionUnit

MX-RB12Paper PassUnit

MX-SL10N Status Indicator(optional)

MX-PCB50 PlockmaticInterface Kit

and

MX-BM50Booklet Maker

MX-CF50 Cover Feeder

Exit Tray Includedwith MX-BM50

MX-TM50Trimming UnitModule

MX-XB50Rail Unit (recommended)

MX-FD50Square Spine Module

and and

and

and

Plockmatic Production Booklet Maker System

Both Units Required

StEP 2: ChooSE finiShing Configuration (continued)

MX-6500N/7500N Configuration Chart

© 2013SharpElectronicsCorporation.Allrightsreserved.

A Network Printing (PCL®6/Adobe PostScript® 3TM Standard)• The MX-PUX1 and MX-PF10 cannot be used with the MX-PE10.• The MX-PE10 requires the MX-PX10

B Network Scanning (Standard) and Faxing

C Security

D Application Integration (MX-AMX2 Application Communication Module and MX-AMX3 External Accounting Module Standard)

E Stamp Kit

MX-PUX1 XPSExpansion Kit

MX-PF10Bar Code Font Kit

MX-PX10Fiery Interface Kit

MX-PE10Fiery Server

(see price list for additional Fiery accessories and software)

and/or or and

andand/or

and

MX-EB11Compact PDF Kit (for Scanning)

MX-EB15HDD Mirroring Expansion Kit

MX-FR43UCommercial Data Security Kit *

MX-EC50CAC Reader(requires MX-FR43U)

MX-AMX1Application IntegrationModule

AR-SU1Stamp Unit(requires AR-SV1)

AR-SV1Stamp Cartridge(requires AR-SU1)

MX-SL10N Status Indicator(optional)

MX-6500N/7500N

STEP 3: SELECT CONNECTIVITY COMPONENTS

* See price list for availability.

MX-6500N/7500N Configuration Chart

© 2013SharpElectronicsCorporation.Allrightsreserved.