Axial submersible pumps QZB type and QHB Francis of submersible pumps
SP UGP-M Submersible Pumps...SP Submersible Pumps UGP-M Installation options Range of materials...
2
Submersible Pumps Applications: Water supply Desalination Irrigation Mining Oil & Gas Power plants Flow Head Power Voltage Speed Materials Type of Installation Features Ranges 50 m /h - 8000 m /h 30 m - 1000 m 30 kW - 3000 kW 380 V - 13800 V 735 rpm - 3500 rpm Cast iron, stainless steel (304, 316, 904L, Duplex, Super Duplex) Low suction or inverted 3 3 www.indarpump.com [email protected] SP UGP-M The SP UGP-M series consists of multistage centrifugal pumps directly coupled to a submersible electric motor in inverted configuration, designed for permanent submersible pumping operation of clean water in a wide range of sectors and applications. Being the pump suction located at the lowest part of the set, this allows increasing the submergence of the set in installations where the water level is low or where the water level is too low to assure the required suction conditions. At the same time, this configuration maximizes pumping, allowing an efficient use of water reserves. The motor, assembled in inverted position on top of the set, includes a cooling shroud that ensures the cooling flow with the discharged fluid. All parts of the pump and the motor are completely designed and manufactured by INDAR. This configuration, along with a wide range of materials, make UGP-M pumps a highly-versatile product which provides perfect solutions to an infinite range of demands.
Transcript of SP UGP-M Submersible Pumps...SP Submersible Pumps UGP-M Installation options Range of materials...
-
Submersible Pumps
Applications:Water supplyDesalinationIrrigationMiningOil & GasPower plants
FlowHead
PowerVoltageSpeed
MaterialsType of Installation
Features Ranges
50 m /h - 8000 m /h 30 m - 1000 m
30 kW - 3000 kW380 V - 13800 V
735 rpm - 3500 rpmCast iron, stainless steel (304, 316, 904L, Duplex, Super Duplex)
Low suction or inverted
3 3
SP UGP-M
The SP UGP-M series consists of multistage centrifugal pumps directly coupled to a submersible electric motor in inverted configuration, designed for permanent submersible pumping operation of clean water in a wide range of sectors and applications.
Being the pump suction located at the lowest part of the set, this allows increasing the submergence of the set in installations where the water level is low or where the water level is too low to assure the required suction conditions. At the same time, this configuration maximizes pumping, allowing an efficient use of water reserves. The motor, assembled in inverted position on top of the set, includes a cooling shroud that ensures the cooling flow with the discharged fluid.
All parts of the pump and the motor are completely designed and manufactured by INDAR. This configuration, along with a wide range of materials, make UGP-M pumps a highly-versatile product which provides perfect solutions to an infinite range of demands.
-
Submersible PumpsSP UGP-MInstallation options Range of materials
1. Radial bearings2. Cooling shroud3. Rotor4. Axial bearing5. Coupling6. Pump radial bearing7. Upper wear ring8. Impeller9. Key10. Washer11. Suction body12. Discharge body13. Upper bearing housing14. Motor casing15. Lower bearing housing16. Friction disc17. Mechanical seal18. Union body19. Spacer sleeve20. Pump shaft21. Pump bowl22. Lower wear ring23. Pump shaft nut24. Strainer
Part list
Inverted or low suction IronStainless steel:
304316904LDuplexSuper duplex
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
1
4
5
6
7
8
9
10
11
The
tech
nica
l dat
a in
this
cat
alog
ue is
sub
ject
to c
hang
e w
ithou
t prio
r no
tice.
SP
UG
P-M
EN
G. 2
017/
01
