Sony Hcd Zx70dvd

HCD-ZX70DVDSERVICE MANUALUS Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model

HCD-ZX70DVD is the Amplifier, DVD/CD player, Tape Deck and Tuner section in MHC-ZX70DVD.

Photo: AEP model

This stereo system is equipped with the Dolby B-type noise reduction system*. * Manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY and the double-D symbol ; are trademarks of Dolby Laboratories Licensing Corporation.

Model Name Using Similar Mechanism DVD Section DVD Mechanism Type Base Unit Name Optical Pick-up Name TAPE Section Model Name Using Similar Mechanism Tape Transport Mechanism Type

NEW CDM53J-DVBU1 DVBU1 KHM-220AAA HCD-ZX30AV TCM-230AWR12

This system incorporates Dolby* Digital and Pro Logic Surround. * Manufactured under license from Dolby Laboratories. Dolby, AC-3, Pro Logic and the double-D symbol ; are trademarks of Dolby Laboratories. Confidential unpublished Works. 1992-1997 Dolby Laboratories, Inc. All rights reserved.

SPECIFICATIONSAmplifier section AUDIO POWER SPECIFICATIONS: (U.S.A. model only)POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 8 ohm loads both channels driven, from 12010,000 Hz; rates 90 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output.Total harmonics distortion Less than 0.07% (8 ohms at 1 kHz, 50 W) Center Speaker: Continuous RMS power output 40 watts (8 ohms at 1 kHz, 10% THD) Rear Speaker: Continuous RMS power output 40 + 40 watts (8 ohms at 1 kHz, 10% THD)

Canadian model:Front Speaker: Continuous RMS power output 100 + 100 watts (8 ohms at 1 kHz, 10% THD) Total harmonics distortion Less than 0.07% (8 ohms at 1 kHz, 50 W) Center Speaker: Continuous RMS power output 40 watts (8 ohms at 1 kHz, 10% THD) Rear Speaker: Continuous RMS power output 40 + 40 watts (8 ohms at 1 kHz, 10% THD)

Continuous RMS power output (reference) 100 + 100 watts (8 ohms at 1 kHz, 10% THD) Music power output (reference) 170 + 170 watts (8 ohms at 1 kHz, 10% THD) Center Speaker: DIN power output (rated) 30 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 40 watts (8 ohms at 1 kHz, 10% THD) Music power output (reference) 60 watts (8 ohms at 1 kHz, 10% THD)

European model:Front Speaker: DIN power output (rated) 80 + 80 watts (8 ohms at 1 kHz, DIN)

Continued on next page

COMPACT DISC DECK RECEIVER

Rear Speaker: DIN power output (rated) 30 + 30 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 40 + 40 watts (8 ohms at 1 kHz, 10% THD) Music power output (reference) 60 + 60 watts (8 ohms at 1 kHz, 10% THD)

Tape player sectionRecording system Frequency response (DOLBY NR OFF) 4-track 2-channel stereo 40 13,000 Hz (3 dB), using Sony TYPE I cassette 40 14,000 Hz (3 dB), using Sony TYPE II cassette

Tuner sectionFM stereo, FM/AM superheterodyne tuner

FM tuner sectionTuning range North American model: Other models: Antenna Antenna terminals Intermediate frequency 87.5 108.0 MHz (100 kHz step) 87.5 108.0 MHz (50 kHz step) FM antenna 75 ohm unbalanced 10.7 MHz

Other models:The following measured at AC 120/220/240 V, 50/60 Hz Front Speaker: DIN power output (rated) 95 + 95 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 120 + 120 watts (8 ohms at 1 kHz, 10% THD) Center Speaker: DIN power output (rated) 30 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 40 watts (8 ohms at 1 kHz, 10% THD) Rear Speaker: DIN power output (rated) 30 + 30 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 40 + 40 watts (8 ohms at 1 kHz, 10% THD) Inputs VIDEO (AUDIO) IN: voltage 250 mV, (phono jacks) impedance 47 kilohms MD IN: voltage 450 mV, (phono jacks) impedance 47 kilohms MIC: sensitivity 1 mV, (mini jack) impedance 10 kilohms (Asian model only) Outputs MD OUT: (phono jacks) VIDEO OUT: (phono jack)

AM tuner section530 1,710 kHz (with the interval set at 10 kHz) 531 1,710 kHz (with the interval set at 9 kHz) European and Middle Eastern models: 531 1,602 kHz (with the interval set at 9 kHz) Other models: 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz Tuning range North American model:

GeneralPower requirements North American model: European model: Australian model: Mexican model: Thai and Chinese models: Other models: 120 V AC, 60 Hz 230 V AC, 50/60 Hz 230 240 V AC, 50/60 Hz 120 V AC, 60 Hz 220 V AC, 50/60 Hz 120 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector

S-VIDEO OUT: (4-pin/mini-DIN jack)

PHONES: (stereo mini jack) FRONT SPEAKER: REAR SPEAKER: CENTER SPEAKER: WOOFER OUT:

voltage 250 mV impedance 1 kilohms max. output level 1Vp-p, unbalanced, Sync negative, load impedance 75 ohms Y: 1Vp-p, unbalanced, Sync negative, C: 0.286Vp-p, load impedance 75 ohms accepts headphones of 8 ohms or more accepts impedance of 8 to 16 ohms accepts impedance of 8 to 16 ohms accepts impedance of 8 to 16 ohms Voltage 1 V, impedance 1 kilohms

Power consumption North American model: European model: Other models: Dimensions (w/h/d) Mass North American model: European model: Other models:

220 watts 220 watts 230 watts Approx. 250 x 375 x 395 mm

Approx. 13.2 kg Approx. 13.0 kg Approx. 13.5 kg

DVD player sectionLaser Frequency response Semiconductor laser DVD (PCM 48 kHz): 2 Hz 22 kHz = (1 dB) CD: 2Hz 20 kHz = (1 dB) More than 90 dB More than 90 dB

Design and specifications are subject to change without notice.

Signal-to-noise ratio Dynamic range Video color system format

NTSC, PAL DIGITAL OUT OPTICAL (Square optical connector jack, rear panel) Wavelength 660 nm Output Level 18 dBm

2

TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. SERVICING NOTES ............................................... 5 GENERAL ................................................................... 7 DISASSEMBLY ......................................................... 9 ASSEMBLY ................................................................. 18 MECHANICAL ADJUSTMENT .......................... 21 DIAGRAMS23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 44 45 46 47 48 49 50 51 6-31. 6-32. 6-33. 6-34. 6-35. 6-36. 6-37. 6-38. 6-39. 6-40. Schematic Diagram MIC Board ............................... Printed Wiring Boards FRONT AMP/HP Boards .... Schematic Diagram FRONT AMP/HP Boards ........ Printed Wiring Board SURR AMP Board ................ Schematic Diagram SURR AMP Board ................... Printed Wiring Boards PANEL/CD SW Boards ...... Schematic Diagram PANEL/CD SW Boards ........... Printed Wiring Board SUB PANEL Board .............. Schematic Diagram SUB PANEL Board ................. Printed Wiring Boards TRANS/SUB TRANS Boards .................................. 6-41. Schematic Diagram TRANS/SUB TRANS Boards .................................. 51 52 53 54 55 56 57 58 59 60 61

6-1. Note for Printed Wiring Boards and Schematic Diagrams ....................................................... 6-2. Printed Wiring Board TK Board ............................... 6-3. Schematic Diagram TK Board ................................. 6-4. Printed Wiring Board MB Board (Side A) ............... 6-5. Printed Wiring Board MB Board (Side B) ............... 6-6. Schematic Diagram MB Board (1/10) ...................... 6-7. Schematic Diagram MB Board (2/10) ...................... 6-8. Schematic Diagram MB Board (3/10) ...................... 6-9. Schematic Diagram MB Board (4/10) ...................... 6-10. Schematic Diagram MB Board (5/10) ...................... 6-11. Schematic Diagram MB Board (6/10) ...................... 6-12. Schematic Diagram MB Board (7/10) ...................... 6-13. Schematic Diagram MB Board (8/10) ...................... 6-14. Schematic Diagram MB Board (9/10) ...................... 6-15. Schematic Diagram MB Board (10/10) ................... 6-16. Printed Wiring Board IF Board ................................ 6-17. Schematic Diagram IF Board ................................... 6-18. Printed Wiring Boards CDM Section ....................... 6-19. Schematic Diagram CDM Section ........................... 6-20. Printed Wiring Board AUDIO Board ....................... 6-21. Schematic Diagram AUDIO Board .......................... 6-22. Printed Wiring Board LEAF SW Board ................... 6-23. Schematic Diagram LEAF SW Board ...................... 6-24. Printed Wiring Board MAIN Board ......................... 6-25. Schematic Diagram MAIN Board (1/5) ................... 6-26. Schematic Diagram MAIN Board (2/5) ................... 6-27. Schematic Diagram MAIN Board (3/5) ................... 6-28. Schematic Diagram MAIN Board (4/5) ................... 6-29. Schematic Diagram MAIN Board (5/5) ................... 6-30. Printed Wiring Board MIC Board ............................

7. 8.

EXPLODED VIEWS ................................................ 65 ELECTRICAL PARTS LIST ............................... 71

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.

3

SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)To Exposed Metal Parts on Set

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. The following caution label is located inside the unit.

0.15 F

1.5 k

AC voltmeter (0.75 V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.

4

SECTION 1 SERVICING NOTESNOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. MODEL IDENTIFICATION Back Panel PART No.

MODEL US model Canadian model AEP, UK, German and North European models Saudi Arabia model Malaysia and Singapore models E model Mexican model Hong Kong model Australian model Thai model Argentine model Chinese model Taiwan model

PART No. 4-227-558-0[] 4-227-558-1[] 4-227-558-2[] 4-227-559-0[] 4-227-559-1[] 4-227-559-2[] 4-227-559-3[] 4-227-559-4[] 4-227-559-5[] 4-227-559-6[] 4-227-559-7[] 4-227-559-8[] 4-227-559-9[]

5

NOTE ON TEMPERATURE OF HEAT SINK

heat sink

Heat sink gets heated up to a high temperature. Be careful not to get burnt.

SERVICE POSITION In checking the DVD block, prepare jig (extension cable J-2501-198-A: 700 mm 17 cores).

IF board

MB board

CONNECT board Connect jig (extension cable J-2501-198-A) to the IF board (CN10) and CONNECT board (CN701).

6

SECTION 2 GENERALLOCATION OF CONTROLS Front View 1 2 3 qf MODE SELECT button qg PUSH ENTER multi stick 456 789 q; qa qs e; ea es ed ef eg eh ej ek el r; ra rs rd qd qf qg qh qj qk ql w; wa ws wd wf qh TITLE button qj DVD MENU button qk m, M buttons ql ., > buttons w; VOLUME knob wa GROOVE button and indicator ws GROOVE-EX button and indicator wd Z B button wf Tape B deck wg Disc 1 indicator wh Disc 2 indicator wj Disc 3 indicator wk Disc 4 indicator wl Disc 5 indicator e; TIMER SELECT indicator ea DISPLAY button es FUNCTION button ed SELECT button wgwhwjwkwl rf ef RETURN button eg HI-DUB button eh NEXT button rg ej PREVIOUS button ek PHONES jack ta rhrjrk rlt; tstdtftgth el REC PAUSE/START button and indicator r; PRO LOGIC button and indicator ra DVD 5.1CH button and indicator rs Z A button rd Tape A deck rf MIC VOL knob (EA, MY, SP, HK, TH, TW, CH) 1 I/1 button and indicator 2 CD SYNC button 3 TAPE A n/N buttons and indicators 4 TAPE B n/N buttons and indicators 5 Fluorescent indicator tube 6 x button 7 DVD u button and indicator 8 TUNER/BAND button 9 SET UP MODE indicator 0 Remote sensor qa SOUND MODE indicator qs DSP button and indicator qd V-GROOVE button and indicator Abbreviation CH : Chinese model EA : Saudi Arabia model MY : Malaysia model HK : Hong Kong model SP : Singapore model TH : Thai model TW : Taiwan model

rg MIC jack (EA, MY, SP, HK, TH, TW, CH) rh DISC 1 button rj DISC 2 button rk DISC 3 button rl DISC 4 button t; DISC 5 button ta Disc tray ts Z 1 button td Z 2 button tf Z 3 button tg Z 4 button th Z 5 button

7

8Parts Identification for the remote (continued)TAPERemote Button(s) TAPE A nN TAPE B nN Starts playback. Each time you press this button, the tape reverses direction. Stops playback. Searches for the beginning of a Track (AMS: Automatic Music Sensor). Fast-forwards or rewinds. x ./> Function

Step 3: Setting the timeDVD/VIDEO CD/CDRemote Button(s) Function Starts playback. Stops playback. Pauses playback. m/M DVD N x X ./> (PREV/NEXT) Selects a chapter or track. For VIDEO CD, use NEXT to see the rest of the menu, and use PREV to go back to the top of the menu.

4

Move the multi stick toward b.

The minute indication flashes.

Parts Identification for the remoteYou can also operate the system with the supplied remote. * You can operate with the remote only. **These buttons do not operate when the function is set to DVD. TVFunction

You must set the time before using the timer functions.

The clock is on a 24-hour system for the European model, and on a 12-hour system for other models.

For illustration purposes, the 12-hour system model is used.

5

Move the multi stick toward V or v repeatedly to set the minute.

?/1 (Power)

2,3,4,5,6TIMERRemote Button(s) SLEEP*Remote Button(s)

1m/M Locates a desired point in a track.Turn the TV on or off. Switch the TV's video input. Change the TV channels. Adjusts the volume of the TV speaker(s). TV ?/1* TV/VIDEO* TV CH +/* TV VOL +/*

6STEP c/C* Performs frame by frame playback of DVD and VIDEO CD. SLOW t/T* Performs slow playback of DVD and VIDEO CD. Exchanges discs. D.SKIP Numeric buttons* Use for the menu operations. DVD SETUP*Function

Press PUSH

To cancel the menu operation

Function Selects a sleep timer.

Press MODE SELECT.

Tips

OTHERSRemote Button(s) ?/1 VOL +/ B/b/V/v ENTER FUNCTION CLEAR* Function Turns the system on or off. Adjusts the volume. Use to select menu and adjust the settings. Selects the function. Restores a setting to the factory preset. MODE SELECT Enters the menu mode. FILE SELECT Selects the preset audio effect file. MD*

Refer to the illustration to use the multi stick. Place your finger on the center of the multi stick and move in the direction you want (up/down or left/ right shown V/v or B/b in this manual). Up (V)PUSH ENTER

TUNERRight (b) TUNER/BAND Selects FM or AM. Remote Button(s)

Displays the setup display on the TV screen. Returns to previously selected screen. Changes the audio sound track. Changes the angles when playing a DVD. Changes the subtitle language. Displays the title menu on the TV screen. Displays the DVD menu on the TV screen. Changes the front panel display.

Left (B)

RETURNO AUDIO* ANGLE* SUBTITLE* TITLE DVD MENU

)Down (v m/M Scans for a station or selects a preset station. Select a preset number. numeric buttons >10* ./> (+, ) Selects a preset number.

All of the functions that use the multi stick can also be performed using V/v/B/b and ENTER on the remote. If youve made a mistake, start over from step 1.

1continuedDISPLAY

To change the time

Press to listen to the connected MD deck. VIDEO* MULTI/2CH PRO LOGIC ON/OFF T.TONE ON/OFF*,** DSP CENTER LEVEL +/*,** REAR LEVEL +/*,** Press to listen to the connected VCR. Press to switch between multi channel and stereo audio. Activates the Pro Logic effects. Use to test each speakers volume. Activates the surround effects. Adjusts the center speaker level. Adjusts the rear speaker level.

Press MODE SELECT when the system is turned off.

Clock Set ? appears. When the system is in the Power Saving Mode, Clock Set ? will not appear. Either set Power Saving Mode off, or follow the steps on this page (To change the time) after turning the power on.

The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following:

DVD DISPLAY* Displays the control menu screens.

2

Press PUSH ENTER.

The hour indication flashes.

1 Press MODE SELECT repeatedly to select Set Up Mode, then press PUSH ENTER. 2 Move the multi stick toward B or b repeatedly to select Timer Set Up ?, then press PUSH ENTER. 3 Move the multi stick toward B or b repeatedly to select Clock Set ?, then press PUSH ENTER. 4 Perform steps 3 through 6 on this page.

Note

The clock settings are canceled when you disconnect the power cord or if a power failure occurs.

This section is extracted from instruction manual.

3

Move the multi stick toward V or v repeatedly to set the hour.

SECTION 3 DISASSEMBLY This set can be disassembled in the order shown below.

UPPER CASE (Page 10)

FRONT PANEL SECTION (Page 10)

BACK PANEL SECTION (Page 11)

TAPE MECHANISM DECK (TCM-230AWR12) (Page 17)

MAIN BOARD (Page 11)

POWER TRANSFORMER (T902) (Page 12)

IF BOARD (Page 12)

FRONT AMP BOARD (Page 13)

MB BOARD (Page 13)

DVD MECHANISM DECK (CDM5J-DVBU) (Page 14)

FITTING BASE (GUIDE) ASSY, BRACKET (CHASSIS) AND MAGNET ASSY (Page 14)

MAGNET ASSY, DVD BASE UNIT (DVBU1) (Page 15)

TRAY (SUB) (Page 16)

OPTICAL PICK-UP, TK BOARD (KHM-220AAA) (Page 15)

CHASSIS (MOLD B) SECTION, STOCKER SECTION AND SLIDER (SELECTION) (Page 16)

9

Note: Follow the disassembly procedure in the numerical order given.

UPPER CASE4 upper case 3 five screws (BVTT 3 8)

1 three screws (CASE3 TP2)

2 three screws (CASE3 TP2)

FRONT PANEL SECTION2 wire (flat type) (15 core) (CN305) 1 connector (CN504) 8 screw (P 3 8) 6 connector (CN691)

5 connector (CN914)

4 wire (flat type) (17 core) (CN503) 3 wire (flat type) (11 core) (CN304) 7 two screws (BVTT 3 6) 9 front panel section

10

BACK PANEL SECTION1 wire (flat type) (13 core) or(15 core) (CN502)

3 connector (CN201) 7 Remove the back panel to direction of the arrow.

2 connector (CN901) 2 connector (CN902)

4 three screws (BVTP 3 8) 4 screw (BVTP 3 8)

2 connector (CN903)

4 fifteen screws (BVTP 3 8)

5

6 connector (CN941)

MAIN BOARD

1 connector (CN1001) 4 connector (CN902)

5 MAIN board

4 connector (CN901)

3 screw (BVTP 3 8)

2 wire (flat type) (23 core) (CN6) 2 wire (flat type) (13 core) (CN8) 3 screw (BVTP 3 8)

11

POWER TRANSFORMER (T902)3 four screws (BVTP 4 6)

1 connector (CN801)

4 Power transforme (T902)

2 connector (CN913)

IF BOARD

2 connector (CN13) 2 connector (CN11) 3 screws (BVTP 3 8) 4 IF board 1 wire (flat type) (23 core) (CN5) 1 wire (flat type) (13 core) (CN7) 1 wire (flat type) (17 core) (CN9)

1 wire (flat type) (17 core) (CN10)

3 two screws (BVTP 3 8) 1 wire (flat type) (10 core) (CN1)

12

FRONT AMP BOARD

9 two screws (BVTP 3 8) 0 heat sink

6 two screws (BVTP 3 8)

1 connector (CN1002)

8 front amp board



5 surrund amp board

4 bracket 3 two screws (BVTP 3 16)

MB BOARD7 three screws (BVTT 3 8) 6 connector (CN013)

3 screw (BVTP 3 8)

4 chassis

8 MB board 5 wire (flat type) (18 core) (CN002)

5 wire (flat type) (18 core) (CN003) qa bracket

9 screw (BVTP 3 8) 0 screw (BVTP 2.6 8)


1 three screws (BVTP 3 8)

13

DVD MECHANISM DECK (CDM5J-DVBU)

1 four screws (BVTP 3 8)

2 Remove the DVD mechanism deck section.

FITTING BASE (GUIDE) ASSY, BRACKET (CHASSIS) AND MAGNET ASSY6 Bracket (chassis) 2 four screws (BTTP M2.6) 4 two screws (BTTP M2.6) 7 connector (CN710) 8 four screws (BTTP M2.6)

9 magnet assy 5 three screws (BTTP M2.6)

3 fitting base (guide) assy 1 two connectors (CN709, 715)

14

MAGNET ASSY, DVD BASE UNIT (DVBU1)

2 four screws (BVTP M2.6) 3 magnet assy 1 connector (CN710)

5 DVD base unit (DVBU1)

4 two screws (PTPWH M2.6)

OPTICAL PICK-UP (KHM-220AAA), TK BOARD5 three step screws 8 optical pick-up (KHM-220AAA) 7 insulator

7 insulator 6 7 insulator


4 TK board

3 two screws (BVTP 2.6)


15

TRAY (SUB)1 Rotating the pulley (LD), shift the slider (selection) in the arrow A direction. 2 Rotating the pulley (mode) in the arrow direction, adjust the tray (sub) to be removed. 3 Rotating the pulley (LD), shift the slider (selection) in the arrow B direction. 4 Rotating the pulley (mode) in the arrow direction, remove the tray (sub) to be removed.

slider (selection)

pully (LD)

stocker section

A B

pully (mode)

tray (sub)

CHASSIS (MOLD B) SECTION, STOCKER SECTION AND SLIDER (SELECTION)6 two screws (PTPWH M2.6)

5 stocker section

7 slider (selection) 8 washer

Pully (LD)

9 compression spring

1 three screws (BVTP M2.6)

4 two step screws

2 chassis (mold B) section

Note: Rotating the pully (LD), shift the slider (selection) to the left.4 two step screws 3 gear (eject)

16

TAPE MECHANISM DECK (TCM-230AWR12)3 Remove the tape mechanism deck section.



CABLE SETTINGWhen connecting the cable from PANEL board (CN704) to CD board (CN754), set it as shown in the figure. FRONT PANEL - BACK VIEW CN704 PANEL board

cable

CN754

CD board

17

SECTION 4 ASSEMBLY

GEARS INSTALLATION (Page 18)

SLIDER (SELECTION) INSTALLATION (Page 19)

STOCKER SECTION INSTALLATION (Page 19)

CHASSIS (MOLD B) SECTION INSTALLATION (Page 20)

Note: Follow the assembly procedure in the numerical order given.

GEARS INSTALLATION

3 gear (gear B)

portion A

Adjust the gear (gear B) with the portion A as shown.

1 Slide the slider (u/d) fully in the arrow direction.

2 gear (U/D slider)

4 gear (gear A)

slider (U/D) gear

gear (gear B)

linearly

Adjust the gear so that it meshes with the bottom tooth of slider (U/D) gear, as shown.

Adjust so as to be aligned with gear B linearly, as shown.

18

SLIDER (SELECTION) INSTALLATION6 two screws (PTPWH M2.6) 2 gear (chuking)

rotary encoder

5 washer 4 compression spring 7 Insert the slider (selection) into the portion A.

Align with the slot of rotary encoder.

portion A

3 convex portion of slider (selection) Gear (chuking) 1 rotary encoder

Insert a convex portion into a groove of gear (chuking). align marking

STOCKER SECTION INSTALLATION2 portion A of tray (sub) 1 stocker section

Hook the portion A of tray (sub) to the slider (selection).

portion A of tray (sub)3 two step screws

sticking of slider (selection)

3 two step screws

19

CHASSIS (MOLD B) SECTION INSTALLATION3 three screws (BVTP M2.6)

2 Insert the gear (eject0 under the gear (LD deceleration).

portion A

1 Insert the portion A of chassis (mold B) section into the portion B of slider (selection).

gear (LD deceleration)

portion B of slider (selection)

20

SECTION 5 MECHANICAL ADJUSTMENTPrecaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque MeasurementMode Torque meter Meter reading

FWD

CQ-102C

FWD back tension REV

CQ-102C

CQ-102RC

REV back tension FF/REW

CQ-102RC

CQ-201B

FWD tension

CQ-403A

REV tension

CQ-403R

3.06 N m to 6.96 N m 31 to 71 g cm (0.43 0.98 oz inch) 0.19 N m to 0.58 N m 2 to 6 g cm (0.02 0.08 oz inch) 3.06 N m to 6.96 N m 31 to 71 g cm (0.43 0.98 oz inch) 0.19 N m to 0.58 N m 2 to 6 g cm (0.02 0.08 oz inch) 6.96 N m to 14.02 N m 71 to 143 g cm (0.98 1.99 oz inch) 9.80 N m 100 g or more (3.53 oz or more) 9.80 N m 100 g or more (3.53 oz or more)

21

MEMO

22

SECTION 6 DIAGRAMS6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSNote on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. % : indicates tolerance. f : internal component. 2 : nonflammable resistor. 5 : fusible resistor. C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice por tant le numro spcifi.

Circuit Boards Location

Note on Printed Wiring Boards: X : parts extracted from the component side. Y : parts extracted from the conductor side. W : indicates side identified with part number. b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A)

TRANS board

Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.

PANEL board MAIN board

MB board is multi-layer printed board. However, the patterns of intermediate-layer have not been included in the diagram. Indication of transistorC Q B E These are omitted.

SUB PANEL board

HP board

MB board

LEAF SW board These are omitted.

Q B C E

U : B+ Line. V : B Line. H : adjustment for repair. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. c : DVD PLAY J : CD PLAY L : DVD/CD PLAY (VIDEO) F : DVD/CD PLAY (AUDIO) g : DVD/CD PLAY (DIGITAL OUT) f : TUNER E : TAPE A PLAY d : TAPE B PLAY G : TAPE B REC N : MIC Abbreviation AR : Argentine model AUS : Australian model CH : Chinese model CND : Canadian model EA : Saudi Arabia model HK : Hong Kong model MX : Mexican model MY : Malaysia model SP : Singapore model TH : Thai model TW : Taiwan model

FRONT AMP board IF board CD SW board AUDIO board

SUB TRANS board TUNER UNIT CLAMP MOTOR board

SENSOR 2 board MIC board (EA, MY, SP, HK, TH, TW, CH) TK board

IN SW board SENSOR board

CONNECTOR board OUT SW board LOAD MOTOR board INIT/COUNT SW board

23

23

HCD-ZX70DVD6-2. PRINTED WIRING BOARD TK Board See page 23 for Circuit Boards Location.

(Page 26)

(Page 26)

24

24

HCD-ZX70DVD6-3. SCHEMATIC DIAGRAM TK Board See page 62 for Waveforms.

(Page 34)

(Page 35)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : DVD STOP

25

25

HCD-ZX70DVD6-4. Semiconductor LocationRef. No. D801 D802 D803 D804 D805 D807 IC001 IC003 IC004 IC202 IC205 IC206 IC302 IC303 IC401 IC501 IC601 IC701 IC904 Q801 Location B-3 C-2 C-2 C-2 B-4 D-5 F-9 F-9 F-9 G-4 F-2 F-2 A-7 C-6 C-10 G-11 G-7 C-3 G-12 B-4

PRINTED WIRING BOARD MB Board (Side A)

See page 23 for Circuit Boards Location.

(Page 24)

(Page 24)

(Page 60)

(Page 60)

(Page 40)

(Page 38)

(Page 38) (Page 38)

(Page 38)

(Page 38)

(Page 38)

26

26

HCD-ZX70DVD6-5. PRINTED WIRING BOARD MB Board (Side B) See page 23 for Circuit Boards Location. Semiconductor LocationRef. No. D701 D806 IC005 IC201 IC203 IC204 IC207 IC304 IC402 IC403 IC404 IC702 IC801 IC802 IC803 IC902 IC905 IC906 IC907 Location D-4 B-3 G-11 G-5 G-5 F-3 G-3 C-6 C-9 C-10 B-10 D-2 C-4 C-2 D-2 G-12 F-12 E-12 D-12

27

27

HCD-ZX70DVD6-6. SCHEMATIC DIAGRAM MB Board (1/10) See page 62 for Waveform.

(Page 33)

(Page 33)

(Page 39) (Page 30)

(Page 37)

(Page 29)

(Page 34) (Page 32)

(Page 36)

(Page 37) (Page 34) (Page 35)

(Page 29) (Page 37)

(Page 33)

(Page 31)

(Page 33)


28

28

HCD-ZX70DVD6-7. SCHEMATIC DIAGRAM MB Board (2/10)

(Page 33)

(Page 31)

(Page 28)

(Page 33)

(Page 33) (Page 28)

(Page 37)


29

29

HCD-ZX70DVD6-8. SCHEMATIC DIAGRAM MB Board (3/10) See page 62 for Waveforms.

(Page 32)

(Page 37)

(Page 33) (Page 34)

(Page 31)

(Page 28)

(Page 35)

(Page 34)

(Page 33)


30

30


(Page 37)

(Page 33)

(Page 28)

(Page 29)

(Page 32)

(Page 30)

(Page 37)

31

31



(Page 28)

(Page 33)

(Page 37)

(Page 31)

(Page 30)

(Page 36)

(Page 37) Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : DVD STOP

32

32


(Page 28)

(Page 29) (Page 28)

(Page 34) (Page 29)

(Page 28)



(Page 32)

(Page 36)

(Page 37)

(Page 37)

(Page 37)

(Page 34)

(Page 31) (Page 35)


33

33



(Page 25)

(Page 37)

(Page 30)

(Page 28) (Page 35)

(Page 33)

(Page 33)

(Page 35)

(Page 30) (Page 35)

(Page 28) (Page 35) Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : DVD STOP

34

34


(Page 33)

(Page 34)

(Page 30)

(Page 34)

(Page 34)

(Page 33)

(Page 25)

(Page 34)

(Page 34)

(Page 34) (Page 28)


35

35


(Page 28) (Page 37)

(Page 32)

(Page 33)

(Page 37)

(Page 33)

(Page 37)


36

36


(Page 32)

(Page 31)

(Page 33) (Page 61)

(Page 39) (Page 36)

(Page 28) (Page 36)

(Page 28) (Page 33)

(Page 36)

(Page 39)


(Page 34)

(Page 29)

(Page 31)


(Page 32)


37

37

HCD-ZX70DVD6-16. PRINTED WIRING BOARD IF Board See page 23 for Circuit Boards Location.(Page 45) (Page 45)

(Page 26)

(Page 45)

(Page 26) (Page 40)

(Page 26)

Semiconductor LocationRef. No. IC1 IC2 Q1 Q2 Q3 Q4 Location E-4 C-3 D-3 C-2 D-2 D-3

(Page 26)

(Page 26)

(Page 26)

38

38

HCD-ZX70DVD6-17. SCHEMATIC DIAGRAM IF Board See page 62 for Waveform.

(Page 49)

(Page 49)

(Page 34)

(Page 28)

(Page 37)

(Page 37)

(Page 37)

(Page 41)

(Page 48)

(Page 37)


39

39

HCD-ZX70DVD6-18. PRINTED WIRING BOARDS CDM Section See page 23 for Circuit Boards Location.

(Page 38)

(Page 26)

40

40

HCD-ZX70DVD6-19. SCHEMATIC DIAGRAM CDM Section See page 62 for IC Block Diagram.

(Page 39)

(Page 37)


41

41

HCD-ZX70DVD

6-20. PRINTED WIRING BOARD AUDIO Board


(PLAYBACK)

TAPE DECK BLOCK (1/2)

JW15

3 1

4 6

05

16(Page 45)

MAIN BOARD CN305

Semiconductor LocationRef. No. IC601 IC602 IC611 Q621 Q622 Q623 Location B-7 B-6 B-1 B-4 B-4 B-3

42

JW14

42

HCD-ZX70DVD6-21. SCHEMATIC DIAGRAM AUDIO Board See page 62 for IC Block Diagram.


N

MAIN BOARD (1/5) CN305

(Page 46)

T621 BIAS OSC

05



43

43

HCD-ZX70DVD

6-22. PRINTED WIRING BOARD LEAF SW Board


Semiconductor Location MAIN Board Ref. No. Location C-9 C-10 H-9 H-8 G-10 H-9 F-7 E-5 F-3 F-3 F-2 F-2 F-3 F-2 F-2 F-2 F-2 F-2 E-10 E-10 E-10 E-10 E-10 F-10 F-10 F-10 F-12 F-12 G-12 G-3 F-3 G-3 H-5 H-4 B-10 F-8 D-7 D-7 B-4 D-4 F-3 I-12 H-12 H-11 G-11 G-10 F-12 H-4 H-5 G-3 H-2 I-3 G-2 Ref. No. Q101 Q102 Q130 Q151 Q152 Q181 Q182 Q183 Q184 Q201 Q202 Q203 Q391 Q392 Q393 Q394 Q395 Q396 Q397 Q501 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q611 Q612 Q613 Q614 Q615 Q616 Q617 Q618 Q691 Q692 Q901 Q902 Q903 Q904 Q905 Q906 Q910 Q911 Q912 Q913 Q941 Q942 Location C-9 C-8 E-12 B-9 C-8 H-9 H-9 H-9 H-9 C-7 C-7 D-7 D-1 C-1 D-1 C-1 C-2 D-2 C-1 E-5 E-11 D-11 E-11 E-11 E-11 F-11 F-11 F-11 H-9 G-9 F-10 G-9 G-9 F-9 E-10 F-10 E-10 F-10 G-12 G-12 H-4 H-4 H-5 H-5 H-4 H-3 G-3 G-3 G-4 F-3 I-7 I-7 D101 D102 D181 D182 D183 D184 D201 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D512 D601 D602 D603 D604 D605 D606 D607 D608 D691 D692 D693 D912 D913 D914 D951 D952 IC101 IC201 IC203 IC204 IC301 IC401 IC501 IC551 IC601 IC602 IC603 IC604 IC691 IC901 IC902 IC903 IC905 IC906 IC907

A DECK PLUNGER


B DECK PLUNGER

05

M

M1 (CAPSTAN)

17

MAIN BOARD CN304

(Page 45)

6-23. SCHEMATIC DIAGRAM LEAF SW Board

(CAPSTAN)

TAPE DECK BLOCK (2/2)A DECK PLUNGER B DECK PLUNGER

(0.2)

0.2( )

O(Page 46)

MAIN BOARD (1/5) CN304

05

Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : TAPE A PLAY ( ) : TAPE B PLAY

44

44

HCD-ZX70DVD6-24. PRINTED WIRING BOARD MAIN Board (Page 51)

See page 23 for Circuit Boards Location.(Page 54)

(Page 38)

(Page 42)

(Page 56)

(Page 44)

(Page 60)

(Page 52)

(Page 52)

45

45

(Page 38)

(Page 38)

HCD-ZX70DVD6-25. SCHEMATIC DIAGRAM MAIN Board (1/5) See page 62 for Waveforms.

(Page 51)

(Page 47)

(Page 44)

(Page 50) (Page 43)

Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : DVD STOP [ ] : TAPE A STOP : Impossible to measure

(Page 48)

46

46

HCD-ZX70DVD6-26. SCHEMATIC DIAGRAM MAIN Board (2/5)

(Page 46)

(Page 55)

(Page 48) Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : DVD STOP

(Page 50)

(Page 49)

47

47


(Page 46)

(Page 57)

(Page 39)

(Page 61)

(Page 47)

(Page 49)

(Page 53) (Page 50)


48

48

HCD-ZX70DVD6-28. SCHEMATIC DIAGRAM MAIN Board (4/5) See page 62 for Waveforms.

(Page 47)

(Page 39)

(Page 39)

(Page 48)

(Page 50)


49

49


(Page 47)

(Page 49)

(Page 46) (Page 53)

(Page 48)


50

50

HCD-ZX70DVD6-30. PRINTED WIRING BOARD MIC Board See page 23 for Circuit Boards Location. 6-31. SCHEMATIC DIAGRAM MIC Board

(Page 46)

(Page 45)

Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM

51

51

HCD-ZX70DVD6-32. PRINTED WIRING BOARDS FRONT AMP/HP Boards Semiconductor LocationRef. No. D801 D802 D821 D831 D851 D871 D881 D911 D951 D961 D962 D963 D981 D982 D983 D984 D991 D992 D993 D994 D995 D996 D997 D998 IC801 Q801 Q821 Q822 Q851 Q871 Q881 Q883 Q891 Q892 Q893 Q894 Q895 Q896 Q897 Q961 Q962 Q963 Q981 Location E-2 F-2 G-1 D-5 E-2 G-2 C-1 G-8 I-9 D-4 D-4 F-3 I-1 I-1 I-1 I-1 H-1 I-1 H-2 I-1 I-3 I-3 I-3 I-3 D-3 D-2 H-2 G-1 D-2 H-3 C-1 D-1 G-7 G-7 G-8 G-8 G-9 G-9 G-9 F-3 F-2 F-2 I-1 (Page 45) (Page 54)


(Page 45)

(Page 60)

(Page 60)

52

52

HCD-ZX70DVD6-33. SCHEMATIC DIAGRAM FRONT AMP/HP Boards

(Page 48)

(Page 61)

(Page 61)

(Page 50)

(Page 55) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM

53

53

HCD-ZX70DVD6-34. PRINTED WIRING BOARD SURR AMP Board Semiconductor LocationRef. No. D1001 D1002 D1051 D1061 D1062 D1081 IC1001 Q1001 Q1051 Q1061 Q1062 Q1063 Q1064 Q1081 Q1091 Q1092 Location B-4 B-3 B-3 A-2 B-4 C-3 C-3 B-3 C-3 B-3 A-4 B-3 B-3 C-4 B-1 B-1

See page 23 for Circuit Boards Location.(Page 52)

(Page 45)

54

54

HCD-ZX70DVD6-35. SCHEMATIC DIAGRAM SURR AMP Board

(Page 53)

(Page 47)

Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

55

55

HCD-ZX70DVD6-36. PRINTED WIRING BOARDS PANEL/CD SW Boards Semiconductor LocationRef. No. D601 D602 D603 D604 D691 D755 D756 D761 D762 D763 IC701 IC702 IC703 IC704 Q601 Q602 Q603 Q663 Q664 Q665 Q690 Q691 Q692 D661 D662 D663 D664 D665 Location A-9 B-9 B-2 A-2 D-2 D-7 D-7 C-3 D-3 D-3 B-6 B-2 D-5 C-4 A-9 A-9 C-2 D-1 D-1 D-2 D-3 D-2 D-2 A-5 A-4 A-4 A-3 A-3


(Page 60)

(Page 45)

(Page 58) (Page 58)

56

56

HCD-ZX70DVD6-37. SCHEMATIC DIAGRAM PANEL/CD SW Boards See page 62 for Waveform. See page 62 for IC Block Diagram.

(Page 61)

(Page 48)

(Page 59)

(Page 59)


57

57

HCD-ZX70DVD6-38. PRINTED WIRING BOARD SUB PANEL Board Semiconductor LocationRef. No. D605 D606 D607 D608 D609 D610 D611 D612 D613 D615 D617 D618 D652 Q605 Q607 Q609 Q611 Q613 Q615 Q617 Q652 Location A-3 A-3 D-6 E-6 B-6 B-7 B-7 B-8 D-9 C-6 E-4 E-4 B-4 C-3 D-4 C-3 C-3 E-4 D-3 D-4 C-3


(Page 56)

(Page 56)

58

58

HCD-ZX70DVD6-39. SCHEMATIC DIAGRAM SUB PANEL Board

(Page 57)

(Page 57)


59

59

HCD-ZX70DVD6-40. PRINTED WIRING BOARDS TRANS/SUB TRANS Boards Semiconductor LocationRef. No. D901 D902 D903 D904 D906 IC901 Q901 Location B-4 B-4 B-4 B-4 A-3 A-4 A-3


(Page 26) (Page 56)

(Page 52)

(Page 52)

(Page 45) (Page 26)

60

60

HCD-ZX70DVD6-41. SCHEMATIC DIAGRAM TRANS/SUB TRANS Boards

(Page 53)

(Page 53)

(Page 57)

(Page 37)

(Page 48)

Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

61

61

IC Block Diagrams CLAMP MOTOR Board IC701VCC 1 OUT2 2 REG 8 VCC IN1 3 INPUT AMP. CONTROL INPUT AMP. POWER AMP. GND 4 6 IN2 5 REFERENCE POWER AMP. 7 OUT1

LOAD MOTOR Board IC702VCC 1 OUT2 2 REG 8 VCC IN1 3 INPUT AMP. CONTROL INPUT AMP. POWER AMP. GND 4 6 IN2 5 REFERENCE POWER AMP. 7 OUT1

Waveforms TK Board 1 IC001 tf (SIGO) (DVD Play Mode)

MB Board 1 IC202 os (X0) 6 IC303 (LRCK)

M54641L

M54641L

1.4 Vp-p

2.3 Vp-p

3.5 Vp-p

80 ns 2 IC001 r; (FE) (DVD Play Mode) 2 IC303 ts (MDP0) (DVD Play Mode)

22.8 s

7 IC401 wg (LRCKO)

Approx. 90 mVp-p

1.8 Vp-p4 Vp-p

AUDIO Board IC602 PC1330HA40 sINVERTER

20.8 s 8 IC401 wh

3 IC001 el (TE) (DVD Play Mode)

3 IC303 tj (JITPWM) (DVD Play Mode)

COMPARATER 1 2 3 4 5 GND 6 VCC 7 8 9 SW R2

3.6 Vp-p

SW R1 GND

SW P1 CONT

SW P2 GND

Approx. 120 mVp-p

4.4 Vp-p

PANEL Board IC704 BA3830F

15.2 s4 IC303 oa (SDCK)

326 ns

9 IC401 ya (Y OUT) (DVD Play Mode (color bar)) (NTSC)

R02 R01 LINE NF LINE IN

1 2 3 4

REFERENCE CURRENT REFERENCE CURRENT

RESET

18 RESET

3.9 Vp-p17 16 15 14 13 12 F01 F02 F03 F04 F05 F06

1 Vp-p

+

BAND PASS FILTER DET

H236 ns 5 IC303 (BCLK) 9 IC401 ya (Y OUT) (DVD Play Mode (color bar)) (PAL)

REC NF REC IN

5 6 + 11 REC LEVEL 10 VCC

RESET C BIAS C GND

7 8 9

3.7 Vp-p

1 Vp-p

H

355 ns

62

62

q; IC401 ys (C OUT) (DVD Play Mode (color bar)) (NTSC)

qd IC501 9 (BCKO)

qk IC701 8 (PWM1)

710 mVp-p

4.3 Vp-p

3.7 Vp-p

H

435 nsq; IC401 ys (C OUT) (DVD Play Mode (color bar)) (PAL) qf IC501 q; (LRCKO)

12.6 sql IC701 9 (PWM0)

710 mVp-p

4 Vp-p

3.7 Vp-p

H

20.8 sqa IC401 yg (COMP OUT) (DVD Play Mode (color bar)) (NTSC) qg IC601 tl (MCK)

12.6 sw; IC001 6 (XT1)

1 Vp-p

4 Vp-p

4.3 Vp-p

H

37.3 nsqa IC401 yg (COMP OUT) (DVD Play Mode (color bar)) (PAL) qh IC601 (CPUCK)

37.3 nswa IC001 qs (SCKO1)

1 Vp-p

3.8 Vp-p

3.8 Vp-p

H

40 nsqs IC401 us (FLDO) qj IC701 7 (PWM2)

29.8 nsws IC001 qf (SCKO2)

3.3 Vp-p

3.7 Vp-p

4.5 Vp-p

40 ms

12.6 s

40.6 ns

63

wd IC001 qj (SCKO3)

2 IC401 qg (X-IN)

5 IC691 q; (DVD Play Mode (color bar)) (PAL)

4.3 Vp-p

1.9 Vp-p

3.5 Vp-p

H

27.2 ns

62.2 ns 3 IC401 w; (RDS-INT) (AEP, UK models) 6 IC691 qd (DVD Play Mode (color bar)) (NTSC)

4.6 Vp-p

2.4 Vp-p

H

IF Board 1 IC1 el (X1)

840 s 4 IC691 qg (DVD Play Mode (color bar)) (NTSC) 6 IC691 qd (DVD Play Mode (color bar)) (PAL)

3.3 Vp-p

2 Vp-p

3.4 Vp-p

H

H

80 ns 4 IC691 qg (DVD Play Mode (color bar)) (PAL)

2 Vp-p

H

MAIN Board 1 IC401 q; (XC-IN) 5 IC691 q; (DVD Play Mode (color bar)) (NTSC)

PANEL Board 1 IC701 oa (XOUT)

1.4 Vp-p

750 mVp-p

4.7 Vp-p

H30.5 s 80 ns

64

SECTION 7 EXPLODED VIEWSNOTE: -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list. Abbreviation AR : Argentine model AUS : Australian model CH : Chinese model CND : Canadian model EA : Saudi Arabia model HK : Hong Kong model MX : Mexican model MY : Malaysia model SP : Singapore model TH : Thai model TW : Taiwan model #4 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiquens pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

(1)

CASE 1

2

3

4

5

#1 #1 #3

7

#1

8 1 9FAN101

#3

#1

6#2

Front panel section #1 Ref. No. 1 2 3 3 4 4 4 4 5 5 5 5 5 5 5 5 5 5 Part No. 3-363-099-21 4-226-746-01 1-773-009-11 1-792-801-11 Description Remark Ref. No. 5 5 5 6 6 6 6 6 6 6 6 7 8 8 8 Part No. 4-227-559-71 4-227-559-81 4-227-559-91 A-4428-997-A A-4473-019-A A-4473-029-A A-4473-670-A A-4473-674-A A-4473-690-A A-4473-857-A A-4475-123-A 4-227-815-01 1-418-687-11 1-476-027-11 Description PANEL, BACK (AR) PANEL, BACK (CH) PANEL, BACK (TW) MAIN BOARD, COMPLETE (US, CND) MAIN BOARD, COMPLETE (AEP, UK) MAIN BOARD, COMPLETE (MY, SP, HK, TW) MAIN BOARD, COMPLETE (E, MX, AR) MAIN BOARD, COMPLETE (EA) MAIN BOARD, COMPLETE (TH) MAIN BOARD, COMPLETE (CH) SCREW (CASE 3 TP2) CASE WIRE (FLAT TYPE) (15 CORE) (AEP, UK, CH) WIRE (FLAT TYPE) (13 CORE) (US, CND, E, EA, MX, HK, MY, SP, AR, TH, TW, AUS) (210mm) 1-693-481-11 TUNER (FM/AM) (US, CND) 1-693-482-11 TUNER (FM/AM) (EA, MY, SP, HK, TH, TW, AUS, MX, AR) 1-693-484-11 TUNER (FM/AM) (E) 1-693-490-11 TUNER (FM/AM) (AEP, UK, CH) 4-227-558-01 PANEL, BACK (US) 4-227-558-11 PANEL, BACK (CND) 4-227-558-21 4-227-559-01 4-227-559-11 4-227-559-21 4-227-559-31 PANEL, BACK (AEP, UK) PANEL, BACK (EA) PANEL, BACK (MY, SP) PANEL, BACK (E) PANEL, BACK (MX) #3 Remark

MAIN BOARD, COMPLETE (AUS) BRACKET (SW) POWER BLOCK (US, CND) POWER BLOCK (EA, MY, SP, HK, TH, TW, AUS, CH) 1-476-028-11 POWER BLOCK (AEP, UK)

4-227-559-41 PANEL, BACK (HK) 4-227-559-51 PANEL, BACK (AUS) 4-227-559-61 PANEL, BACK (TH)

8 1-476-029-11 POWER BLOCK (E, MX, AR) 9 1-676-976-11 SUB TRANS BOARD (US, CND, AEP, UK) FAN101 1-763-072-11 FAN, D.C.

65

(2)

FRONT PANEL SECTION

56 56not supplied

78 59 67 83#3

56

not supplied

66 64 65 60 61 56 62 56 56 63#1

56 68 56 69

57 56#3

58

55EA, MY, SP, HK, TH, TW, CHnot supplied

56

71 70not supplied

56

53 51

54 58 77

56not supplied

72 #1#3

73 52 74 56 85 80 84 81 82 79Ref. No. 51 52 53 54 55 56 57 58 59 60 60 60 60 61 62 63 64 65 66 67 Part No. 4-226-734-01 4-226-735-01 4-226-537-01 4-226-715-01 4-214-385-91 4-951-620-01 1-676-972-11 4-224-104-11 1-676-971-11 X-4952-797-1 Description Remark Ref. No. 68 68 68 68 69 70 70 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 Part No. Description Remark

TCM-230PWR12

76 75not supplied

BUTTON (A), EJECT BUTTON (B), EJECT SPRING (TC EJECT), COIL KNOB, VOLUEME KNOB (MIC) (EA, MY, SP, HK, TH, TW, CH) SCREW (2.6X8), +BVTP MIC BOARD (EA, MY, SP, HK, TH, TW, CH) DAMPER HP BOARD PANEL ASSY, FRONT (US)

A-4473-011-A PANEL BOARD, COMPLETE (US, CND, AEP, UK, E, MX, AR, AUS) A-4473-023-A PANEL BOARD, COMPLETE (EA, MY, SP, HK, TW) A-4473-683-A PANEL BOARD, COMPLETE (TH) A-4473-851-A PANEL BOARD, COMPLETE (CH) 1-769-938-11 WIRE (FLAT TYPE) (11 CORE) A-4428-661-A A-4473-825-A A-4473-243-A 1-773-022-11 1-773-045-11 4-227-458-01 4-227-459-01 X-4952-712-1 X-4952-711-1 4-957-577-01 3-056-508-01 4-226-741-11 4-226-737-01 4-226-729-01 4-226-728-01 CD SW BOARD, COMPLETE (EXCEPT TH, CH) CD SW BOARD, COMPLETE (CH) CD SW BOARD, COMPLETE (TH) WIRE (FLAT TYPE) (15 CORE) (300mm) WIRE (FLAT TYPE) (17 CORE) (170mm) SPRING (TC A) SPRING (TC B) HOLDER (B) ASSY, TC HOLDER (A) ASSY, TC SCREW PTP WH (2.6X8) (DIA. 10) EMBLEM, DVD PANEL (CD), ALUMINUM LID (CD) LID, TC PANEL (TC), ALUMINUM

X-4952-798-1 PANEL ASSY, FRONT (AEP, UK) X-4952-799-1 PANEL ASSY, FRONT (EA, MY, SP, HK, TH, TW, CH) X-4952-812-1 PANEL ASSY, FRONT (CND, E, MX, AR, AUS) 4-226-733-01 LOCK (B) 4-226-731-01 LOCK (LID) 4-226-732-01 4-226-755-01 4-227-544-01 4-226-713-01 A-4473-013-A LOCK (A) COVER, LOCK SPRING, TENSION CURSOR SUB PANEL BOARD, COMPLETE (EXCEPT TH, CH)

67 67

A-4473-680-A SUB PANEL BOARD, COMPLETE (TH) A-4473-848-A SUB PANEL BOARD, COMPLETE (CH)

4-226-712-41 PANEL (STR), ALUMINUM 4-226-897-01 SPRING (CD) 4-227-460-01 SPRING, TENSION

66

112 111

(3)

CHASSIS SECTION#4

110 110US, CND

EA, MY, SP, TW

110UK, HK

120#4

123#6 #6

AEP, EA, MY, SP, HK, TW

110 110E, MX, TH, CH#3

121 114#3 #3 #3

115 104#4 #4

110AR#1

AUS

122

T902

#3

#3

not supplied

106#5 #3

#3

102CDM53F-K2BD38

107not supplied #5

109

116

not supplied

117#3

118 119not supplied

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. Remark

101#3

113

Ref. No. 101 102 104 106 106 106 106 106 106 106 * 107 107 109 109 109 109 109 0 110 0 110 0 110 0 110 0 110 0 110 0 110

Part No. 4-965-822-01 1-792-798-11 1-676-975-11 A-4428-992-A A-4473-016-A

Description

Remark

Ref. No. 0 111 0 112 113 113 113 114 115 115 115 115 115 115 115 115 116 117 118 119 120 121 122 123 0 T902 0 T902 0 T902

Part No. 1-569-008-21 1-770-019-11 A-4473-238-A A-4473-693-A A-4473-860-A 4-227-814-01 A-4473-710-A A-4473-711-A A-4473-712-A A-4473-713-A A-4473-714-A A-4473-715-A A-4473-709-A A-4473-861-A 1-792-799-11 1-792-800-11 1-769-977-11 1-792-802-11 1-792-797-11 1-792-797-21 4-951-620-01 4-227-816-01 1-435-475-11 1-435-391-11 1-435-392-11

Description

FOOT WIRE (FLAT TYPE) (17 CORE) (120mm) TRANS BOARD FRONT AMP BOARD, COMPLETE (US) FRONT AMP BOARD, COMPLETE (AEP, UK)

ADAPTOR, CONVERSION 2P (EA, MY, SP, TW) ADAPTOR, CONVERSION PLUG 3P (UK, HK) IF BOARD, COMPLETE (EXCEPT TH, CH) IF BOARD, COMPLETE (TH) IF BOARD, COMPLETE (CH) BRACKET (DVD) MB BOARD, COMPLETE (US, CND) MB BOARD, COMPLETE (AEP, UK) MB BOARD, COMPLETE (E, MX, AR) MB BOARD, COMPLETE (EA) MB BOARD, COMPLETE (MY, SP, HK, TW) MB BOARD, COMPLETE (AUS) MB BOARD, COMPLETE (TH) MB BOARD, COMPLETE (CH) WIRE (FLAT TYPE) (10 CORE) WIRE (FLAT TYPE) (23 CORE) (160mm) WIRE (FLAT TYPE) (13 CORE) (150mm) WIRE (FLAT TYPE) (17 CORE) (170mm) WIRE (FLAT TYPE) (18 CORE) (PLATE: BLUE) WIRE (FLAT TYPE) (18 CORE) (PLATE: WHITE) SCREW (2.6X8), +BVTP HEAT SINK (DVD) TRANSFORMER, POWER (US, CND) TRANSFORMER, POWER (AEP, UK) TRANSFORMER, POWER (EXCEPT US, CND, AEP, UK)

A-4473-026-A FRONT AMP BOARD, COMPLETE (EA, MY, SP, HK, TW, AUS) A-4473-668-A FRONT AMP BOARD, COMPLETE (E, MX, AR) A-4473-687-A FRONT AMP BOARD, COMPLETE (TH) A-4473-695-A FRONT AMP BOARD, COMPLETE (CND) A-4473-854-A FRONT AMP BOARD, COMPLETE (CH) 3-703-244-00 BUSHING (2104), CORD (US, CND, AEP, UK, EA, MY, SP, HK, TW, AR, AUS, CH) 3-703-571-11 BUSHING (S) (4516), CORD (E, TH, MX) A-4428-632-A SURR AMP BOARD, COMPLETE (AEP, UK) A-4428-643-A SURR AMP BOARD, COMPLETE (E, EA, MY, SP, HK, TW, MX, AR, AUS) A-4428-994-A SURR AMP BOARD, COMPLETE (US, CND) A-4473-251-A A-4473-831-A 1-690-608-11 1-777-070-11 1-777-071-51 1-782-464-21 1-783-531-11 1-783-941-21 1-791-901-11 SURR AMP BOARD, COMPLETE (TH) SURR AMP BOARD, COMPLETE (CH) CORD, POWER (AUS) CORD, POWER (CND) CORD, POWER (AEP, UK, EA, MY, SP, HK, TW) CORD, POWER (CH) CORD, POWER (US) CORD, POWER (AR) CORD, POWER (E, TH, MX)

67

(4)

DVD MECHANISM DECK SECTION-1 (CDM53J-DVBU1)

178 151 151not supplied

177 151 164

151 151 151 151 160 161 151 168 159 151 176 167 151 169 151 151 158 170 174 171 157 156 155 151 151 175 151 154 151 153 151M702not supplied

162 165 151

170 171

173 172

152

Ref. No. 151 152 153 154 155 156 157 158 159 160 161 162 164 165

Part No. 4-218-253-11 1-675-728-11 4-220-261-01 1-675-724-11 1-675-726-11 4-212-676-01 4-212-674-01 4-985-672-01 A-4672-873-A 1-675-725-11 1-675-727-11 4-964-461-02 1-675-723-11 A-4672-872-D

Description SCREW (M2.6), +BTTP LOAD MOTOR BOARD GEAR (EJECT) INIT/COUNT SW BOARD SENSOR BOARD SPRING (LID), TORSION LID (DISC) SCREW (+PTPWH M2.6), FLOATING BASE (GUIDE) ASSY, FITTING OUT SW BOARD SENSOR 2 BOARD HOLDER (SENSOR) IN SW BOARD BASE (MAGNET) ASSY, FITTING

Remark

Ref. No. 167 168 169 170 171 172 173 174 175 176 177 178 M702

Part No. 4-211-235-01 4-211-236-01 4-211-231-01 4-211-214-01 4-211-232-01 4-211-228-01 4-214-130-01 1-675-722-11 3-341-549-01 4-226-821-02

Description BELT (COMMUNICATION) BELT (LOADING) PULLEY (MODE) PULLEY (LD) GEAR (LD DECELERATION) LEVER (GOOSENECK) GEAR (TRAY) CONNECTOR BOARD SCREW(2.6X12) (DIA.7.5), +PTP WH PLATE, CHUCKING

Remark

3-053-844-01 YOKE 4-223-293-01 RETAINER, YOKE X-4950-342-1 MOTOR (LOADING) ASSY

68

(5)

DVD MECHANISM DECK SECTION-2 (CDM53J-DVBU1)222 221#3

201 223

243#3

219B

220 217#3

224 219

225S707

not supplied

215 214

227 229 230

216 218

228

not supplied

231 232B

212 210 213#3 #3

A

233 234 235 219

238 240 211 204 204 226 204 209 241 242 219 210 202A

237 202 201not supplied M701

236

202

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

Ref. No. 201 202 204 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225

Part No. 4-985-672-01 3-053-847-01 4-223-291-11 4-223-292-11 4-211-244-01 4-211-223-01 4-933-134-01 4-221-504-01 4-211-211-01 4-211-210-01 4-211-215-01 4-211-232-01 4-211-214-01 4-218-253-21 4-211-237-01 4-212-677-01 4-212-678-01 4-211-233-01 4-211-230-01 4-211-245-01

Description SCREW (+PTPWH M2.6), FLOATING INSULATOR TRAY (DVD) HOLDER (DVD) SCREW, STEP SLIDER (U/D) SCREW (M2.6), +PTPWH BASE (STOCKER), FITTING STOCKER (R) STOCKER (L) GEAR (EJECT) GEAR (MODE DECELERATION) PULLEY (LD) SCREW (M2.6), +BTTP BELT (MODE) SLIDER (SHUTTER) SPRING (SHUTTER), TENSION SLIDER (SELECTION) GEAR (CHUCKING) SPRING, COMPRESSION

Remark

Ref. No. 226 227 228 229 230 231 232 233 234 235 236 237 238 0 240 241 242 243 M701 S707

Part No. 1-675-729-11 4-211-221-01 4-211-217-01 4-211-242-11 4-211-240-01 4-211-216-01 4-211-241-01 4-216-879-01 3-701-446-21 4-211-218-01 4-211-220-01 4-211-219-01 4-981-923-01 8-820-081-09 A-4725-157-A 4-951-620-41 4-211-234-01 X-4950-341-1 1-418-045-01

Description CLAMP MOTOR BOARD GEAR (LD MOVABLE) GEAR (SELECTION) SHAFT (SELECTION GEAR) GEAR (LD DECELERATION B) GEAR (RELAY) LEVER (SELECTION) SPRING (GEAR), COMPRESSION WASHER GEAR (GEAR A) GEAR (U/D SLIDER) GEAR (GEAR B) SCREW (M), STEP OPTICAL PICK-UP KHM-220AAA TK BOARD, COMPLETE

Remark

SCREW (2.6), +BVTP BRACKET (STOCKER T) MOTOR (CLAMP) ASSY (ELEVATOR UP/DOWN) ENCODER, ROTARY (DISC TRAY ADDRESS DETECT)

69

(6)

TAPE MECHANISM DECK SECTION (TCM-230AWR12)

309 310 311not supplied

312

M1

307 308

314

313

310

305 308 315#10

306 316

305

315

303 306 302 301 302 304

Ref. No. 301 302 303 304 305 306 307 308 309

Part No. A-2100-898-A 3-911-116-42 A-2007-845-A 3-376-464-11 X-3374-156-4 X-3374-155-4 A-2007-838-A 3-041-947-01 X-3378-041-1

Description

Remark

Ref. No. 310 311 312 313 314 315 316 M1

Part No. 3-041-946-01 X-3378-040-1 4-227-239-01 X-3378-042-1 X-3378-043-1

Description BELT (CAPSTAN B) FLYWHEEL (A-FWD) ASSY BELT (CAPSTAN C) FLYWHEEL (B-FWD) ASSY FLYWHEEL (B-REV) ASSY

Remark

TAPE MECHANISM ASSY TCM-230AWR12 RIVET, PUSH AUDIO BOARD, COMPLETE SCREW(+PTT 2.6X6),GROUND POINT PINCH LEVER (REV) ASSY PINCH LEVER (FWD) ASSY LEAF SW BOARD, COMPLETE BELT (FR) FLYWHEEL (A-REV) ASSY

3-019-208-01 WASHER, STOPPER 4-227-455-02 SPRING (HALF), TORSION X-3378-241-1 MOTOR ASSY (CAPSTAN/REEL)

70

SECTION 8 ELECTRICAL PARTS LISTNOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable Abbreviation AR : Argentine model MX : Mexican model AUS : Australian model MY : Malaysia model CH : Chinese model SP : Singapore model CND : Canadian model TH : Thai model EA : Saudi Arabia model TW : Taiwan model HK : Hong Kong model Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u: , for example: uA. . : A. . uPA. . : PA. . uPB. . : PB. . uPC. . : PC. . uPD. . : PD. . CAPACITORS uF: F COILS uH: H

AUDIOThe components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiquens pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

When indicating parts by reference number, please include the board.

Ref. No.

Part No.

Description

Remark

Ref. No. C642

Part No.

Description 47uF 20%

Remark 16V

A-2007-845-A AUDIO BOARD, COMPLETE ********************** < CAPACITOR >

1-104-664-11 ELECT < CONNECTOR >

CN601 C301 C302 C303 C304 C305 C311 C313 C314 C315 C331 C332 C333 C401 C402 C403 C404 C405 C411 C413 C414 C415 C431 C432 C433 C601 C602 C611 C612 C621 C622 C623 C624 C625 C627 C628 1-162-289-31 1-126-968-11 1-162-282-31 1-130-483-00 1-107-715-11 1-162-289-31 1-162-282-31 1-130-487-00 1-126-233-11 1-137-427-11 1-162-288-31 1-162-209-31 1-162-289-31 1-126-968-11 1-162-282-31 1-130-483-00 1-107-715-11 1-162-289-31 1-162-282-31 1-130-487-00 1-126-233-11 1-137-427-11 1-162-288-31 1-162-209-31 1-104-396-11 1-104-396-11 1-104-396-11 1-104-396-11 1-137-150-11 1-126-961-11 1-136-155-00 1-130-481-00 1-130-481-00 1-124-903-11 1-136-153-00 CERAMIC ELECT CERAMIC MYLAR ELECT CERAMIC CERAMIC MYLAR ELECT MYLAR CERAMIC CERAMIC CERAMIC ELECT CERAMIC MYLAR ELECT CERAMIC CERAMIC MYLAR ELECT MYLAR CERAMIC CERAMIC ELECT ELECT ELECT ELECT FILM ELECT FILM MYLAR MYLAR ELECT FILM 390PF 100uF 100PF 0.01uF 22uF 390PF 100PF 0.022uF 22uF 120PF 330PF 27PF 390PF 100uF 100PF 0.01uF 22uF 390PF 100PF 0.022uF 22uF 120PF 330PF 27PF 10uF 10uF 10uF 10uF 0.01uF 2.2uF 0.015uF 0.0068uF 0.0068uF 1uF 0.01uF 10% 20% 10% 5% 20% 10% 10% 5% 20% 5% 10% 5% 10% 20% 10% 5% 20% 10% 10% 5% 20% 5% 10% 5% 20% 20% 20% 20% 5% 20% 5% 5% 5% 20% 5% 50V 6.3V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 100V 50V 50V 50V 50V 50V 50V

1-568-834-21 SOCKET, CONNECTOR 15P < IC >

IC601 IC602 IC611

8-759-111-44 IC uPC4570C-1 8-759-143-54 IC uPC1330HA 8-759-111-44 IC uPC4570C-1 < COIL >

L331 L431

1-410-780-11 INDUCTOR 1-410-780-11 INDUCTOR < TRANSISTOR >

27mH 27mH

Q621 Q622 Q623

8-729-142-46 TRANSISTOR 8-729-142-46 TRANSISTOR 8-729-801-93 TRANSISTOR < RESISTOR >

2SC2001TP-LK 2SC2001TP-LK 2SD1387-34-TP

R301 R302 R303 R304 R305 R311 R312 R314 R315 R331 R401 R402 R403 R404 R405 R411 R412 R414 R415

1-247-881-00 1-249-409-11 1-249-433-11 1-247-889-00 1-247-858-11 1-247-881-00 1-247-807-31 1-247-882-11 1-247-850-11 1-249-430-11 1-247-881-00 1-249-409-11 1-249-433-11 1-247-889-00 1-247-858-11 1-247-881-00 1-247-807-31 1-247-882-11 1-247-850-11

CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON

120K 220 22K 270K 13K 120K 100 130K 6.2K 12K 120K 220 22K 270K 13K 120K 100 130K 6.2K

5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%

1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

71

AUDIORef. No. R431 R601 R602 R608 R609 R611 R612 0 R621 0 R622 R623 R624 R625

CD SW

CLAMP MOTORRemark 12K 220 220 220 22K 220 220 5.6 5.6 18K 18K 10K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

CONNECTORRef. No. S631 Part No. Description Remark 1-762-875-21 SWITCH, KEYBOARD (Z1)

Part No.

Description

1-249-430-11 CARBON 1-249-409-11 1-249-409-11 1-249-409-11 1-249-433-11 1-249-409-11 1-249-409-11 1-212-851-00 1-212-851-00 1-249-432-11 1-249-432-11 CARBON CARBON CARBON CARBON CARBON CARBON FUSIBLE FUSIBLE CARBON CARBON

S632 1-762-875-21 SWITCH, KEYBOARD (DISC 1) S633 1-762-875-21 SWITCH, KEYBOARD (DISC 2) S634 1-762-875-21 SWITCH, KEYBOARD (DISC 3) S635 1-762-875-21 SWITCH, KEYBOARD (DISC 4) S636 1-762-875-21 SWITCH, KEYBOARD (DISC 5) ************************************************************** 1-675-729-11 CLAMP MOTOR BOARD ******************* < CAPACITOR > C701 C702 C706 C711 C712 1-162-306-11 1-126-964-11 1-162-306-11 1-162-306-11 1-162-306-11 CERAMIC ELECT CERAMIC CERAMIC CERAMIC < CONNECTOR > * CN712 1-568-954-11 PIN, CONNECTOR 5P < DIODE > D701 8-719-983-66 DIODE MTZJ-T-72-3.6B < IC > IC701 8-759-633-65 IC M54641L < RESISTOR > R701 1-249-411-11 CARBON 330 5% 1/4W R702 1-249-401-11 CARBON 47 5% 1/4W ************************************************************** 1-675-722-11 CONNECTOR BOARD ***************** < CONNECTOR > CN701 1-770-169-11 CONNECTOR, FFC/FPC 17P < TRANSISTOR > 0.01uF 10uF 0.01uF 0.01uF 0.01uF 30% 20% 30% 30% 30% 16V 50V 16V 16V 16V

1/4W 1/4W F 1/4W F 1/4W 1/4W 1/4W

1-249-429-11 CARBON

< VARIABLE RESISTOR > RV301 RV311 RV341 RV401 RV411 RV441 1-238-598-11 1-238-598-11 1-241-768-11 1-238-598-11 1-238-598-11 RES, ADJ, CARBON 2.2K RES, ADJ, CARBON 2.2K RES, ADJ, CARBON 220K RES, ADJ, CARBON 2.2K RES, ADJ, CARBON 2.2K

1-241-768-11 RES, ADJ, CARBON 220K < TRANSFORMER >

T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION ************************************************************** A-4428-661-A CD SW BOARD, COMPLETE (EXCEPT TH, CH) A-4473-243-A CD SW BOARD, COMPLETE (TH) A-4473-825-A CD SW BOARD, COMPLETE (CH) *********************** < LED > D661 D662 D663 D664 D665 8-719-058-64 8-719-058-64 8-719-058-64 8-719-058-64 8-719-058-64 LED LED LED LED LED SEL5823A-TP15 (1) SEL5823A-TP15 (2) SEL5823A-TP15 (3) SEL5823A-TP15 (4) SEL5823A-TP15 (5)

< RESISTOR > R628 R629 R630 R631 R632 R633 R634 R635 R636 R661 R662 R663 R664 R665 1-249-420-11 1-249-422-11 1-247-843-11 1-249-425-11 1-249-427-11 1-249-429-11 1-249-431-11 1-249-434-11 1-249-438-11 1-249-409-11 1-249-409-11 1-249-409-11 1-249-409-11 1-249-409-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON < SWITCH > S627 S628 S629 S630 1-762-875-21 1-762-875-21 1-762-875-21 1-762-875-21 SWITCH, KEYBOARD (Z5) SWITCH, KEYBOARD (Z4) SWITCH, KEYBOARD (Z3) SWITCH, KEYBOARD (Z2) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. 1.8K 2.7K 3.3K 4.7K 6.8K 10K 15K 27K 56K 220 220 220 220 220 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

Q701

8-729-029-66 TRANSISTOR < RESISTOR >

RT1N141S-TP

R707 1-249-424-11 CARBON 3.9K 5% 1/4W R708 1-249-417-11 CARBON 1K 5% 1/4W R709 1-249-429-11 CARBON 10K 5% 1/4W **************************************************************

72

FRONT AMPRef. No. Part No. Description Remark Ref. No. C872 C891 C892 C893 C911 C912 C951 C951 C952 4.7uF 4.7uF 220PF 100PF 47uF 0.068uF 0.068uF 0.1uF 0.1uF 0.01uF 0.01uF 4.7uF 47uF 0.1uF 0.1uF 20% 50V (EXCEPT US, CND) 20% 100V (US, CND) 10% 50V 10% 50V 20% 10V 50V 50V 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 30% 16V 30% 16V 20% 100V 20% 50V 5% 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 20% 50V 20% 50V (EXCEPT US, CND) 20% 100V (US, CND) 10% 50V 10% 50V 20% 10V 50V 50V 50V (AEP, UK, CH) 5% 50V (AEP, UK, CH) 30% 16V 30% 30% 30% 30% 20% 16V 16V 16V 16V 100V 5% 5% 5% 5% 5% 5% 5% C952 Part No. 1-126-959-11 1-104-665-11 1-126-961-11 1-104-665-11 1-130-777-00 Description ELECT ELECT ELECT ELECT MYLAR 0.47uF 100uF 2.2uF 100uF 0.1uF 20% 20% 20% 20% 10% Remark 50V 10V 50V 10V 100V A-4428-992-A FRONT AMP BOARD, COMPLETE (US) A-4473-016-A FRONT AMP BOARD, COMPLETE (AEP, UK) A-4473-026-A FRONT AMP BOARD, COMPLETE (EA, MY, SP, HK, TW, AUS) A-4473-668-A FRONT AMP BOARD, COMPLETE (E, MX, AR) A-4473-687-A FRONT AMP BOARD, COMPLETE (TH) A-4473-695-A FRONT AMP BOARD, COMPLETE (CND) A-4473-854-A FRONT AMP BOARD, COMPLETE (CH) *************************** < CAPACITOR > C801 C801 C802 C803 C804 C806 C807 C808 C809 C811 C812 C821 C822 C831 C832 1-126-963-11 ELECT 1-128-581-11 ELECT 1-162-286-31 CERAMIC 1-162-282-31 CERAMIC 1-104-664-11 ELECT 1-136-495-11 MYLAR 1-136-495-11 MYLAR 1-136-165-00 MYLAR 1-136-165-00 MYLAR 1-162-306-11 CERAMIC 1-162-306-11 1-107-721-11 1-107-717-11 1-136-165-00 CERAMIC ELECT ELECT MYLAR

1-130-777-00 MYLAR 1-127-753-11 ELECT 1-135-516-11 ELECT 1-127-753-11 ELECT 1-135-516-11 ELECT

0.1uF 10% 100V 3300uF 20% 71V (EXCEPT US, CND, AEP, UK) 3300uF 20% 63V (US, CND, AEP, UK) 3300uF 20% 71V (EXCEPT US, CND, AEP, UK) 3300uF 20% 63V (US, CND, AEP, UK) 3300uF 3300uF 0.1uF 0.1uF 22uF 22uF 100uF 47uF 220uF 10uF 47uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 20% 20% 5% 5% 20% 20% 20% 20% 20% 20% 20% 5% 5% 5% 5% 50V 50V 50V 50V 100V 100V 50V 50V 100V 50V 50V 50V 50V 50V 50V 50V

C953 C954 C955 C956 C961 C962 C963 C964 C981 C982 C983 C984 C991 C992 C993 C994

1-135-515-11 1-135-515-11 1-136-165-00 1-136-165-00 1-128-560-11 1-128-560-11 1-126-968-11 1-126-967-11 1-128-564-11 1-126-964-11 1-126-967-11 1-164-159-11 1-136-165-00 1-136-165-00 1-136-165-00

ELECT ELECT MYLAR MYLAR ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC MYLAR MYLAR MYLAR

1-136-165-00 MYLAR

1-136-165-00 MYLAR < CONNECTOR >

C833 C834 C835 C836 C837 C851 C851 C852 C853 C854 C856 C857 C858 C859 C861 C862 C863 C864 C865 C871

1-136-165-00 MYLAR 1-136-165-00 MYLAR 1-136-165-00 MYLAR 1-136-165-00 MYLAR 1-126-963-11 ELECT 1-126-963-11 ELECT 1-128-581-11 ELECT 1-162-286-31 CERAMIC 1-162-282-31 CERAMIC 1-104-664-11 ELECT 1-136-495-11 MYLAR 1-136-495-11 MYLAR 1-136-165-00 MYLAR 1-136-165-00 MYLAR 1-162-306-11 CERAMIC 1-162-306-11 1-162-306-11 1-162-306-11 1-162-306-11 1-107-721-11 CERAMIC CERAMIC CERAMIC CERAMIC ELECT

0.1uF 0.1uF 0.1uF 0.1uF 4.7uF 4.7uF 4.7uF 220PF 100PF 47uF 0.068uF 0.068uF 0.1uF 0.1uF 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF 4.7uF

CN801 CN803 CN804

1-691-768-11 PLUG (MICRO CONNECTOR) 6P 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P < DIODE >

D801 D802 D821 D831 D851 D871 D881 D911 D951 D961 D962 D963 D981 D982 D983 D984 D991 D992 D993 D994 D995

8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-302-37 8-719-302-37 8-719-947-58 8-719-947-58 8-719-911-19 8-719-024-99 8-719-079-21 8-719-079-21 8-719-160-56 8-719-024-99 8-719-024-99 8-719-024-99 8-719-024-99

DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE

1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 RBV-602 RBV-602 MTZJ-T-72-13C MTZJ-T-72-13C 1SS133T-72 11ES2-NTA2B MTZJ-T-72-20D MTZJ-T-72-20D RD12F-T7B2 11ES2-NTA2B 11ES2-NTA2B 11ES2-NTA2B 11ES2-NTA2B

8-719-024-99 DIODE 11ES2-NTA2B

73

FRONT AMPRef. No. D996 D997 D998 Part No. Description Remark Ref. No. R822 R823 R824 R825 R826 R827 R828 R829 R830 R831 Part No. 1-260-089-11 1-260-089-11 1-260-089-11 1-249-402-11 1-249-417-11 1-249-433-11 1-249-417-11 1-249-437-11 1-249-417-11 1-260-076-11 Description CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 150 150 150 56 1K 22K 1K 47K 1K 10 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/2W 1/2W 1/2W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/2W (AEP, UK, CH) 8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B < EARTH TERMINAL > * EPT951 1-537-738-21 TERMINAL, EARTH < IC > IC801 IC801 8-749-017-03 IC STK412-020 (EXCEPT US, CND, AEP, UK) 8-749-017-01 IC STK412-000 (US, CND, AEP, UK) < COIL > L811 L831 L832 L833 L861 1-420-872-00 1-420-872-00 1-420-872-00 1-420-872-00 1-420-872-00 COIL, AIR-CORE (AEP, UK, CH) COIL, AIR-CORE (AEP, UK, CH) COIL, AIR-CORE (AEP, UK, CH) COIL, AIR-CORE (AEP, UK, CH) COIL, AIR-CORE (AEP, UK, CH) < TRANSISTOR > Q801 Q821 Q822 Q851 Q871 Q881 Q883 Q891 Q892 Q893 Q894 Q895 Q896 Q897 Q961 Q962 Q963 Q981 8-729-140-84 8-729-231-55 8-729-900-63 8-729-140-84 8-729-231-55 8-729-119-76 8-729-119-78 8-729-140-84 8-729-140-84 8-729-140-82 8-729-119-78 8-729-119-78 8-729-119-78 8-729-119-78 8-729-140-84 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC1841TP-PAFAEA 2SC2878AB-TPE2 BN1F4M-TP 2SC1841TP-PAFAEA 2SC2878AB-TPE2 2SA1175-HFE 2SC2785TP-HFE 2SC1841TP-PAFAEA 2SC1841TP-PAFAEA 2SA988TP-PAFAEA 2SC2785TP-HFE 2SC2785TP-HFE 2SC2785TP-HFE 2SC2785TP-HFE 2SC1841TP-PAFAEA 2SA1376-T-L 2SC1841TP-PAFAEA 2SA1932 (TP)

R832 R833 R834 R835 R836

1-260-076-11 CARBON 1-260-076-11 CARBON 1-260-076-11 CARBON 1-260-076-11 CARBON 1-260-076-11 CARBON

10 10 10 10 10

5%

1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W

R837 R838 R839 R851 R852 R853 R853 R854 0 R855 R856 R857 R858 R859 R861 R862

1-249-437-11 1-249-437-11 1-249-437-11 1-249-417-11 1-249-438-11

CARBON CARBON CARBON CARBON CARBON

47K 47K 47K 1K 56K

1-249-414-11 CARBON 1-249-415-11 1-249-438-11 1-234-499-21 1-249-417-11 1-249-431-11 1-249-441-11 1-260-076-11 1-260-076-11

560 5% 1/4W (EXCEPT US, CND, AEP, UK) CARBON 680 5% 1/4W (US, CND, AEP, UK) CARBON 56K 5% 1/4W ENCAPSULATED COMPONENT CARBON 1K 5% 1/4W 15K 100K 10 10 10 5% 5% 5% 5% 1/4W 1/4W 1/2W 1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 1/2W 1/2W 1/2W 1/2W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 2W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

8-729-140-82 TRANSISTOR 8-729-140-84 TRANSISTOR 8-729-048-52 TRANSISTOR < RESISTOR >

CARBON CARBON CARBON CARBON

1-260-076-11 CARBON

R801 R802 R803 R803 R804 0 R805 R806 R807 R808 R809 R811 R812 R814 R815 R821

1-249-417-11 CARBON 1-249-438-11 CARBON 1-249-414-11 CARBON 1-249-415-11 CARBON 1-249-438-11 CARBON 1-234-499-21 1-249-417-11 1-249-431-11 1-249-441-11 1-260-076-11

1K 5% 1/4W 56K 5% 1/4W 560 5% 1/4W (EXCEPT US, CND, AEP, UK) 680 5% 1/4W (US, CND, AEP, UK) 56K 5% 1/4W

R871 R872 R873 R874 R875 R876 R877 R878 R879 R880 0 R881 R883 R885 R887 R889 R891 R892 R894 R895 R896

1-260-089-11 1-260-089-11 1-260-089-11 1-260-089-11 1-249-402-11 1-249-417-11 1-249-433-11 1-249-417-11 1-249-441-11 1-247-903-00 1-215-889-00 1-249-437-11 1-249-429-11 1-249-441-11 1-249-429-11 1-249-438-11 1-249-439-11 1-249-429-11 1-249-429-11 1-249-435-11

CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON METAL OXIDE CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON

150 150 150 150 56 1K 22K 1K 100K 1M 330 47K 10K 100K 10K 56K 68K 10K 10K 33K

5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%

ENCAPSULATED COMPONENT CARBON 1K 5% CARBON 15K 5% CARBON 100K 5% CARBON 10 5% 10 10 47K 47K 150 5%

1/4W 1/4W 1/4W 1/2W

1-260-076-11 CARBON 1-260-076-11 CARBON 1-249-437-11 CARBON 1-249-437-11 CARBON 1-260-089-11 CARBON

1/2W (AEP, UK, CH) 5% 1/2W (AEP, UK, CH) 5% 1/4W 5% 1/4W 5% 1/2W

74



FRONT AMPRef. No. R897 R898 R900 0 R951 0 R952 Part No. 1-249-433-11 1-249-425-11 1-249-425-11 1-215-877-11 Description CARBON CARBON CARBON METAL OXIDE 22K 4.7K 4.7K 22K 22K Remark 5% 1/4W 5% 1/4W 5% 1/4W 5% 1W F (E, MX, AR, AUS) 5% 1W F (E, MX, AR, AUS) 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1W 1W 1/4W F 1/4W F 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W C1 C2 C4 C5 C6 C8 R966 R967 0 R968 R969 R970 R971 R972 R973 R974 R982 R983 R984 1-249-435-11 1-249-435-11 1-202-972-61 1-249-439-11 1-249-433-11 1-249-421-11 1-249-433-11 1-249-421-11 1-249-429-11 1-249-427-11 CARBON CARBON FUSIBLE CARBON CARBON CARBON CARBON CARBON CARBON CARBON 33K 33K 1 68K 22K 2.2K 22K 2.2K 10K 6.8K 2.2K 10K Ref. No. Part No. Description

HP

IFRemark

A-4473-238-A IF BOARD, COMPLETE (EXCEPT TH, CH) A-4473-693-A IF BOARD, COMPLETE (TH) A-4473-860-A IF BOARD, COMPLETE (CH) ******************* < CAPACITOR > 1-124-779-00 1-163-038-00 1-163-031-11 1-115-464-91 1-126-206-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 10uF 20% 0.1uF 0.01uF 0.0022uF 10% 100uF 20% 0.01uF 16V 25V 50V 630V 6.3V 50V

1-215-877-11 METAL OXIDE

R961 R962 0 R963 0 R964 R965

1-215-870-11 1-215-870-11 1-212-881-11 1-212-881-11 1-249-431-11

METAL OXIDE METAL OXIDE FUSIBLE FUSIBLE CARBON

1.5K 1.5K 100 100 15K

1-163-031-11 CERAMIC CHIP < CONNECTOR >

CN1 CN3 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14

1-784-369-21 1-770-215-11 1-793-991-11 1-793-991-11 1-793-989-11 1-793-989-11 1-784-376-11 1-784-869-21 1-793-687-31 1-793-687-31

CONNECTOR, FFC/FPC 10P PIN, CONNECTOR (PC BOARD) 7P CONNECTOR, FFC/FPC 23P CONNECTOR, FFC/FPC 23P CONNECTOR, FFC/FPC 13P CONNECTOR, FFC/FPC 13P CONNECTOR, FFC/FPC 17P CONNECTOR, FFC (LIF (NON-ZIF)) 17P PIN, CONNECTOR (1.5mm) (SMD) 5P PIN, CONNECTOR (1.5mm) (SMD) 5P

1-249-421-11 CARBON 1-249-429-11 CARBON < RELAY >

1-793-687-11 PIN, CONNECTOR (1.5mm) (SMD) 5P 1-793-687-11 PIN, CONNECTOR (1.5mm) (SMD) 5P < FERRITE BEAD >

RY881

1-755-141-11 RELAY < TERMINAL >

1-694-677-11 TERMINAL BOARD (4P) (FRONT SPEAKER, IMPEDANCE USE 8-16) TM802 1-694-674-11 TERMINAL BOARD (6P) (REAR/CENTER SPEAKER, IMPEDANCE USE 8-16) ************************************************************** 1-676-971-11 HP BOARD ********* < CAPACITOR > C1691 C1692 C1693 1-162-294-31 CERAMIC 1-162-294-31 CERAMIC 1-164-159-11 CERAMIC < CONNECTOR > CN1691 1-785-316-51 PIN, CONNECTOR (STRAIGHT) 4P < EARTH TERMINAL > * EPT1691 1-537-738-21 TERMINAL, EARTH < INDUCTOR > FB1691 1-412-473-21 INDUCTOR FB1692 1-412-473-21 INDUCTOR FB1693 1-412-473-21 INDUCTOR < JACK > J1691 1-793-829-11 JACK, HEADPHONE (PHONES) ************************************************************** The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le nemro spcifi. 0uH 0uH 0uH 0.001uF 0.001uF 0.1uF 10% 10% 50V 50V 50V

TM801

FB1 FB2 FB3

1-414-813-11 FERRITE 1-414-813-11 FERRITE 1-414-813-11 FERRITE < IC >

0uH 0uH 0uH

IC1 IC2

8-759-645-59 IC uPD784214AYGF-501-3BA 8-759-497-44 IC TC7WH125FU (TE12R) < RESISTOR >

JR1 JR3 JR4 JR5 JR6 JR7 JR8 JR9 JR10 JR11 JR14 JR15 JR16 JR17 JR18 JR19 JR20 JR23 JR24 JR25

1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-089-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00

SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT RES-CHIP SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT

0 0 0 0 0 0 0 0 47K 0 0 0 0 0 0 0 0 0 0 0

5%

1/10W

75

IFRef. No. JR26 JR27 JR28 JR29 JR30 JR31 JR32 JR33 JR34 JR35 JR36 JR37 JR38 JR39 JR40 JR41 JR42 JR43

INIT/COUNT SWPart No. 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 Description SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT

IN SW

LEAF SWRemark Ref. No. Part No. Description < COMPOSITION CIRCUIT BLOCK > Remark

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RB1 RB2 RB3

1-233-576-11 RES, CHIP NETWORK 100 1-233-810-21 RES, NETWORK 100K (3216) 1-233-576-11 RES, CHIP NETWORK 100 < VIBRATOR >

X1 1-781-893-21 VIBRATOR, CERAMIC (CHIP TYPE) (12.5MHz) ************************************************************** 1-675-724-11 INIT/COUNT SW BOARD ******************** < SWITCH > 1-771-264-11 SWITCH, PUSH (DETECTION) (1 KEY) (INIT) 1-771-264-11 SWITCH, PUSH (DETECTION) (1 KEY) (COUNT) ************************************************************** 1-675-723-11 IN SW BOARD ************ < CONNECTOR > S705 S706

1-216-296-00 SHORT 1-216-296-00 SHORT 1-216-296-00 SHORT < TRANSISTOR >

Q1 Q2 Q3 Q4

8-729-027-31 8-729-025-28 8-729-025-28 8-729-025-28

TRANSISTOR FET FET FET < RESISTOR >

DTA124EKA-T146 2SK1828TE85L 2SK1828TE85L 2SK1828TE85L

* CN710

1-568-941-11 PIN, CONNECTOR 3P < SWITCH >

R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R17 R18 R19 R20 R21 R22 R30 R31 R32 R33 R34 R35 R44 R48 R49 R50 R60 R68

1-216-174-00 1-216-073-00 1-216-097-00 1-216-073-00 1-216-089-00 1-216-025-00 1-216-073-00 1-216-061-00 1-216-061-00 1-216-061-00 1-216-061-00 1-216-073-00 1-216-073-00 1-216-222-00 1-216-073-00 1-216-097-00 1-216-073-00 1-216-198-00 1-216-097-00 1-216-198-00 1-216-097-00 1-216-049-11 1-216-097-00 1-216-025-00 1-216-097-00 1-216-025-00 1-216-073-00 1-216-174-00 1-216-025-00

RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP

100 10K 100K 10K 47K 100 10K 3.3K 3.3K 3.3K 3.3K 10K 10K 10K 10K 100K 10K 1K 100K 1K 100K 1K 100K 100 100K 100 10K 100 100

5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%

1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/8W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W

S703 1-771-218-11 SWITCH, MICRO (MID IN) S704 1-771-218-11 SWITCH, MICRO (IN) ************************************************************** A-2007-838-A LEAF SW BOARD, COMPLETE ************************ < CAPACITOR > C1001 1-107-716-11 ELECT < CONNECTOR > CN1001 1-568-860-21 SOCKET, CONNECTOR 17P < DIODE > D1001 D1002 8-719-911-19 DIODE 1SS133T-72 8-719-911-19 DIODE 1SS133T-72 < PHOTO INTERRUPTER > IC1001 IC1002 8-749-014-38 PHOTO INTERRUPTER SG-264 8-749-014-38 PHOTO INTERRUPTER SG-264 < TRANSISTOR > Q1001 8-729-029-56 TRANSISTOR < RESISTOR > R907 R1001 R1002 R1003 R1004 R1005 R1006 1-247-879-11 1-249-409-11 1-249-409-11 1-249-414-11 1-247-834-11 CARBON CARBON CARBON CARBON CARBON 100K 220 220 560 1.3K 300 24K 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W DTA144ESA-TP 33uF 20% 10V

1-247-818-11 CARBON 1-247-864-11 CARBON

76

LEAF SWRef. No. R1007 R1008 Part No. Description 7.5 1K 5% 5% Remark 1/4W 1/4W Ref. No. C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C132 C133 C137 C142 C144 < CONNECTOR > C146 * CN713 1-568-954-11 PIN, CONNECTOR 5P < DIODE > D702 8-719-109-85 DIODE MTZJ-T-72-5.1B < IC > IC702 8-759-633-65 IC M54641L < RESISTOR > R703 1-249-411-11 CARBON 330 5% 1/4W R704 1-249-401-11 CARBON 47 5% 1/4W ************************************************************** A-4428-997-A A-4473-019-A A-4473-029-A A-4473-670-A A-4473-674-A MAIN BOARD, COMPLETE (US, CND) MAIN BOARD, COMPLETE (AEP, UK) MAIN BOARD, COMPLETE (MY, SP, HK, TW) MAIN BOARD, COMPLETE (E, MX, AR) MAIN BOARD, COMPLETE (EA) C153 C155 C157 C158 C159 C160 C161 C162 C163 C164 C165 C166 C167 C168 C169 C170 C171 C172 C173 C174 C175 C181 C192 C194 20% 5% 5% 10% 10% 50V 50V 50V 50V 50V C196 1-126-960-11 1-126-964-11 1-136-157-00 1-136-157-00 1-163-019-00 1-163-019-00 1-164-161-11 1-164-161-11 1-126-964-11 1-136-495-11 1-130-481-00 1-130-481-00 1-163-017-00 1-164-161-11 1-136-159-00 1-126-964-11 1-126-964-11 1-136-165-00 1-136-165-00 1-126-960-11 Part No. 1-164-161-11 1-164-161-11 1-126-964-11 1-136-495-11 1-130-481-00 1-130-481-00 1-163-017-00 1-164-161-11 1-136-159-00 1-126-964-11 1-126-964-11 1-136-165-00 1-136-165-00 1-126-960-11 1-104-665-11 1-136-165-00 1-104-664-11 1-104-664-11 1-163-009-11 1-163-038-00 1-247-780-00 CARBON 1-249-417-11 CARBON

LOAD MOTORDescription CERAMIC CHIP CERAMIC CHIP ELECT MYLAR MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP MYLAR ELECT ELECT MYLAR MYLAR ELECT ELECT MYLAR ELECT ELECT CERAMIC CHIP CERAMIC CHIP 0.0022uF 0.0022uF 10uF 0.068uF 0.0068uF 0.0068uF 0.0047uF 0.0022uF 0.033uF 10uF 10uF 0.1uF 0.1uF 1uF 100uF 0.1uF 47uF 47uF 0.001uF 0.1uF 10uF 0.1uF 220PF 220PF 220PF 10% 10% 20% 5% 5% 5% 5% 10% 5% 20% 20% 5% 5% 20% 20% 5% 20% 20% 10%

MAINRemark 100V 100V 50V 50V 50V 50V 50V 100V 50V 50V 50V 50V 50V 50V 10V 50V 16V 16V 50V 25V

< VARIABLE RESISTOR > RV1001 1-241-785-11 RES, ADJ, CARBON 10K RV1002 1-241-785-11 RES, ADJ, CARBON 10K < SWITCH > S1001 S1002 S1003 S1004 S1005 1-570-953-11 1-570-953-11 1-771-333-11 1-771-205-11 1-771-205-11 SWITCH, PUSH (1 KEY) (A PLAY) SWITCH, PUSH (1 KEY) (B PLAY) SWITCH, LEAF (A HALF) SWITCH, LEAF (A 120/70) SWITCH, LEAF (REC A)

S1006 1-771-333-11 SWITCH, LEAF (B HALF) S1008 1-771-205-11 SWITCH, LEAF (B 120/70) S1009 1-771-205-11 SWITCH, LEAF (REC B) ************************************************************** 1-675-728-11 LOAD MOTOR BOARD ****************** < CAPACITOR > C703 C704 C705 1-162-306-11 CERAMIC 1-126-964-11 ELECT 1-162-306-11 CERAMIC 0.01uF 10uF 0.01uF 30% 20% 30% 16V 50V 16V

1-126-964-11 ELECT 1-163-038-00 CERAMIC CHIP 1-163-001-11 CERAMIC CHIP 1-163-001-11 CERAMIC CHIP 1-163-001-11 CERAMIC CHIP

20%

50V 25V 10% 50V (AEP, UK, CH) 10% 50V (AEP, UK, CH) 10% 50V (AEP, UK, CH) 50V 50V 50V 50V 50V 50V 100V 100V 50V 50V 50V 50V 50V 100V 50V 50V 50V 50V 50V 50V

ELECT ELECT MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT MYLAR MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP MYLAR ELECT ELECT MYLAR MYLAR ELECT

1uF 10uF 0.022uF 0.022uF 0.0068uF 0.0068uF 0.0022uF 0.0022uF 10uF 0.068uF 0.0068uF 0.0068uF 0.0047uF 0.0022uF 0.033uF 10uF 10uF 0.1uF 0.1uF 1uF 100uF 1uF 220PF 220PF 220PF

20% 20% 5% 5% 10% 10% 10% 10% 20% 5% 5% 5% 5% 10% 5% 20% 20% 5% 5% 20%

A-4473-690-A MAIN BOARD, COMPLETE (TH) A-4473-857-A MAIN BOARD, COMPLETE (CH) A-4475-123-A MAIN BOARD, COMPLETE (AUS) ********************* 4-875-327-31 HEAT SINK 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S < CAPACITOR/SHORT > C103 C107 C108 C109 C110 1-126-960-11 1-136-157-00 1-136-157-00 1-163-019-00 1-163-019-00 ELECT MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP 1uF 0.022uF 0.022uF 0.0068uF 0.0068uF

Sony Hcd Zx70dvd

Documents

Transcript of Sony Hcd Zx70dvd