Sony Audio

Sony Audio

Audio Make

Audio Model Problem Solution

SONY APM007AV AMP LED FADES & AUDIO CUTS OFF AFTER A MINUTE

CHANGE Q301 (PN:8-729-2815-2).

SONY AVU270 AC SWITCH OUTLET NOT WORKING.

REPLACE D902, (PN:8-719-107-4)

SONY AVU360 INTERMITTENT SOUND ON TV CHANNELS AFTER 1 HOUR

REPLACE IF-B001 I. F. BLOCK

SONY BM600 NO PLAYBACK, HAS FF & RWD (FLYWHEEL GEAR BROKEN).

REPLACE THE GEAR WITH AN IMPROVED ONE, 3-574-629-11

SONY BM900 NO PLAYBACK, HAS FF & RWD (FLYWHEEL GEAR BROKEN).

REPLACE THE GEAR WITH AN IMPROVED ONE, 3-574-629-11

SONY CCDM8U DOOR NOT LATCHING & WILL NOT EJECT UNABLE TO COMPLETE ANY

REPLACE CAM ASSEMBLY WITH IMPROVED ONE (PN: X-3712-031-1)

SONY CDP101 WON'T ACCEPT DISC OR READ TOC

ADJUST RV202 TO BRING VOLTAGE AT IC203 PIN 5 FROM 2.85 VDC TO 2.55 VDC ADJUS

SONY CDP101 LEFT OUTPUT DISTORTED REPLACE Q504

SONY CDP101 SKIPS JUMPS TRACK READJUST RF PLL FREQUENCY & FOCUS GAIN

SONY CDP101 HISS ON 1 CHANNEL OTHER CHANNEL DEAD

REPLACE Q505

SONY CDP101 DISC SUDDENLY SPEEDS UP & THEN EJECTS SOMETIMES IN STOP MODE HEAR DISC MOTOR

REPLACE IC203

SONY CDP101 DISC WON'T SPIN DUE TO RESTING ON TABLE ASSEMBLY

REPLACE CHASSIS ASSEMBLY

SONY CDP101 HISS ON ONE CHANNEL OTHER CHANNEL DEAD.

REPLACE Q505.

SONY CDP101 DISC MOTOR TURNED BACKWARD AT MAXIMUM SPEED.

FOUND CRYSTALL X502 (8.6436 MHZ) WAS DEFECTIVE.

SONY CDP101 RANDOMLY SKIPS PROGRAM MATERIAL

REPLACE OPTICAL BLOCK KSS-100A

SONY CDP101 DISC EJECTS BEFORE TABLE OF CONTENTS (TOC) CAN BE READ

FREE STUCK OBJECTIVE LENS-COIL ASSEMBLY

SONY CDP101 STAYS IN SCAN REPLACED IC304

SONY CDP101 WON'T READ TABLE OF CONTENTS EJECTS AFTER 3 TIMES

REPLACE PICKUP ASSEMBLY (PN: KSS-100A)

SONY CDP101 CLICKING POPPING NOISE REPLACE IC504 & ALLIGNED

SONY CDP101 POPPING & CLICKING NOISES ALTERNATING FROM LEFT & RIGHT CHANNEL

CHECK TIMER DISPLAY SWITCH IN FRONT PANEL

SONY CDP101 DRAW WON'T OPEN NO LED INDICATION ON OPEN CLOSE BUTTON

REPLACE R390 4.7 OHM 1/4 WATT OPEN IN +13V LINE

SONY CDP101 STATIC IN BOTH CHANNELS AFTER 10 MINUTES

REPLACE CX79034 & COMPLETE ALIGNMENT

SONY CDP101 NO AUDIO (SLED MOVES TO OUTSIDE OF DISC)

REINSTALL & RESOLDER X101 CONTACTS

SONY CDP101 WON'T READ TABLE OF CONTENTS

RESOLDER BAD CONNECTIONS OF IC403

SONY CDP101 DISC WOULD EJECT BEFORE THE T.O.C. COULD BE READ

FREE STUCK OBJECTIVE LENS-COIL ASSY.

SONY CDP101 UNIT STAYS IN SCAN. REPLACED IC304.

SONY CDP101 DISTORTED SOUND. REPLACE RAM IC501.

SONY CDP101 WHISTLE ON LEFT CHANNEL REDRESS AUDIO LEADS AROUND CNP22 FOR BEST ELIMINATION OF NOISE.

SONY CDP101 WITH DISC IN PLACE TRANSPORT WOULD CLOSE BUT WOULD ALSO REJECT IT.

CNJ36 TO BSL MOTOR WAS INTERMITTENTLY LOOSE CAUSING VOLTAGE TO MOTOR TO VARY

SONY CDP101 NO ANALOG OUTPUT FROM IC507 (D/A CONVERTER).

REPLACE IC507 D/A CONVERTER.

SONY CDP101 WOULD NOT READ TOC RESOLDER BAD CONECTIONS OF IC403

SONY CDP101 UNIT WILL NOT ACCEPT DISC ADJUST RR PPL AND CLV

SONY CDP101 DOOR WILL NOT ALWAYS WORK OR WILL OPEN OR CLOSE BY ITSELF

REPLACE IC304 STK6922 WITH A BX-1201 (8-741-120-10) IC.

SONY CDP101 STATIC NOISE IN BOTH CHANNELS AFTER 10 MINUTES

REPLACE CX79034 & COMPLETE ALIGNMENT.

SONY CDP101 POPPING AND CLICKING NOISES ALTERNATING FROM LEFT AND RIGHT CHANNEL.

CHECK TIMER DISPLAY SWITCH IN THE FRONT PANEL.

SONY CDP101 SOUND DISTORTED REPLACE RAM IC501

SONY CDP101 UNIT WILL NOT READ TOC EJECTS AFTER 3 TIMES

REPLACE PICK-UP ASSY. (PN:KSS-100A).

SONY CDP101 SKIP OF PROGRAM MATERIAL AT RANDOM.

REPLACE OPTICAL BLOCK KSS-100A

SONY CDP101 DISC WOULD SUDDENLY SPEED UP AND THEN EJECT.

REPLACE IC203.

SONY CDP101 DISC EJECTS AFTER TWO OR THREE SECONDS.

REMOVE SOLDER BRIDGE BETWEEN R333 AND JW122 COMPLETE ALIGNMENT PHASE RV201

SONY CDP101 DISC WILL NOT SPIN DUE TO RESTING ON TABLE ASSEMBLY.

REPLACE CHASSIS ASSEMBLY.

SONY CDP101 DOOR OPENS SLOW REPLACE IC304, R390, R391.

SONY CDP101 DISK MOTOR WOULD RUN AT POWER ON. NO LOADING OR CHUCKING OPERATION.

NO CLOCK WAVEFORM AT PIN 2 OF IC102 OR PIN 2 OF IC104. REPLACE X101

SONY CDP101 SKIPPING JUMPS TRACK. READJUST RF PLL FREQUENCY AND FOCUS GAIN

SONY CDP101 NO AUDIO SLED MOVES TO OUTSIDE OF DISC.

REINSTALL AND RESOLDER X101 CONTACTS.

SONY CDP101 INTERMITTTENT OPERATION Q510 IC503 X502

SONY CDP101 DISTORTED LEFT OUTPUT REPLACE Q504

SONY CDP101 FOCUS COIL OSCILLATES REPLACE IC204 STK6922 WITH NEW TYPE BX1201

SONY CDP102 INTERMITTENTLY SKIPS TRACKS RE LUBERICATE SLIDE SHAFT REF #511

SONY CDP102 NOISE IN AUDIO AFTER 15-20 MINUTES

REPLACED INTERMITTENT IC310 (PN: 875201520) & CHECK CX23035

SONY CDP102 INTERMITTENT MISTRACKING ADD A RESISTOR OF 33K OHM (1/6W 1-247-867-00) BETWEEN PIN 25 CX20108 & GROUN

SONY CDP102 SKIPS TRACKS INTERMITTENTLY. RE LUBERICATE SLIDE SHAFT (REF. #511).

SONY CDP102 NOISE IN THE AUDIO AFTER 15-20 MIN.

REPLACED INTERMITTENT IC310 (PN: 875201520) ALSO CHECK CX23035

SONY CDP110 DISTORTED AUDIO. REPLACED IC303 CXD1135Q (PN: 875232205).

SONY CDP110 EJECT IS INTERMITTENT. REPLACE DRIVE BELT. NEW PN 4-917-548-02

SONY CDP110 UNIT MAY NOT FOCUS OR MAY NOT TRACK.

REPLACED IC2 CXA1082AQ (PN: 875203165).

SONY CDP110 AUDIO DISTORTED REPLACED IC303 CXD1135Q (PN: 875232205)

SONY CDP110 MAKES A NOISE & DOOR WON'T STAY CLOSED

REPLACED IC6 (PN: 875930390)

SONY CDP110 UNIT MAKES A NOISE & DOOR WILL NOT STAY CLOSED.

REPLACED IC6 (PN: 875930390).

SONY CDP110 WON'T FOCUS OR TRACK REPLACED IC2 CXA1082AQ (PN: 875203165)

SONY CDP190 IC102 REPEATEDLY FAILS IF IC102 IS DETERMINED TO BE BAD REPLACE AND TEST

SONY CDP190 DISTORTION AFTER WARM UP REPLACED IC211, (PN: 8-752-334-51).

SONY CDP190 UNIT ACCEPTS DISC & READS T.O.C. BUT WILL NOT MOVE OPTICAL ASSY OUTWARD HOME

REPLACED IC102 FOCUS/TRACKING/SPINDLE/SLED DRIVE O.P AMP/BUNNER IC 875982194

SONY CDP200 DISC MOTOR WON'T TURN READJUSTED FOCUS OFFSET RV103 & RF PLL

SONY CDP200 START TO SKIP AFTER WARMUP REPLACED IC406 STK6932 WITH IMPROVED (PN: BX1234)

SONY CDP200 SKIPS OR MISSES COMPLETE TRACKS

REPLACED CHUCKING ARM (PN: X490220130)

SONY CDP200 UNIT SKIPS OR MISS COMPLETE TRACKS.

REPLACED CHUCKING ARM (PN: X490220130).

SONY CDP200 UNIT SKIPS POOR CONTACT BETWEEN THE CLUTCH IN THE CHUCKING ARM AND THE DISC

SONY CDP200 AFTER WARM-UP THE UNIT STARTED SKIPPING.

REPLACED IC406 STK6932 WITH NEW IMPROVED ONE BX1234.

SONY CDP200 DISC TABLE MOTOR TURNS BACKWARDS AT HIGH SPEED AT TURN ON.

REPLACED X501 CRYSTAL (PN: 152799900). NOTE: FOUND NO CLOCK AT PIN 15/16 IC5

SONY CDP200 THE DISC MOTOR DOESN'T TURN.

READJUSTED FOCUS OFFSET (RV103) AND RF PLL.

SONY CDP203 NO FUNCTION DISPLAY LIGHTS UP STRANGELY

REPLACED IC803, (PN:8-759-303-41).

SONY CDP203 INTERMITTENT NO EJECT. LM BELT 4-913-797-01 & TENSION SPRING 1-913-796-01

SONY CDP203 BACKGROUND NOISE IS HEARD DURING QUIET PASSAGES OF MUSIC.

REPLACED IC302 D/A CONVERTER (PN: 875201520).

SONY CDP203 ERATTIC OPERATION OR INTERMITTENTLY IT WILL ENTER SHUFFLE PLAY.

RESOLDER INTERMITTENT CONNECTION ON R809 WHICH IS ACROSS THE MASTRO CONTROL

SONY CDP203 SCRATCHES ON THE DISC REPLACE THE DISC SUPPORT WITH NEW TYPE, P/N X-4912-513-1

SONY CDP203ES CONSTANT LOW LEVEL ILLUMINATION OF UNUSED DISPLAY SECTIONS

REPLACE D914 SHORTED 6V ZENER DIODE.

SONY CDP21 EJECT IS INTERMITTENT. REPLACE DRIVE BELT. NEW PN 4-917-548-02

SONY CDP25 SCRATCHED DISC REPLACE THE DISC SUPPORTS WITH THE DISC SUPPORT KIT. X-4912-53-1

SONY CDP25 DISTORTED AUDIO. REMOVED BURR FROM OPTICAL PICK-UP.

SONY CDP25 AUDIO DISTORTED REMOVED BURR FROM OPTICAL PICK-UP

SONY CDP270 LOADS & UNLOADS CD TRAY ASSEMBLY

REPLACE LOADING BELT

SONY CDP291 NOISE IN AUDIO AT LOW LEVEL (SOUNDS LIKE PHONO CRACKS SNAPS & POPS)

REPLACE X251

SONY CDP291 AUDIO HAS INTERMITTENT STATIC NOISE

REPLACE IC211

SONY CDP30 WHEN NECESSARY TO REPLACE OPTICAL BLOCK ASSY, VERIFY CORRECT NUMBER

KSS-121A P/N X-4910-424-1, KSS-120C P/N X-4910-441-1

SONY CDP30 WON'T READ TOC REPLACED (PN:CX20109) RF AMP.


SONY CDP30 NO FOCUS. BAD SOLDER CONNECTION ON PIN 32 IC106 LD ON.

SONY CDP30 NO FOCUS BAD SOLDER CONNECTION ON PIN 32 IC106

SONY CDP302 NOISY UNRELIABLE REPLACE C220 10MFD X 50V.

SONY CDP302 NO DISPLAY ALL OTHER FUNCTIONS OK

REPLACE DISPLAY

SONY CDP302 WON'T READ TOC WOULD FOCUS SEARCH & THEN STOP WON'T PLAY AT ALL

REPLACE LEAKY C218 LEAKY

SONY CDP302 MACHINE FUNCTIONED NORMALLY WITH EXCEPTION OF HAVING NO, DISPLAY.

REPLACE DISPLAY.

SONY CDP302 INTERMITTENT WOULD NOT READ T.O.C.

RESOLDER ALL CONNECTIONS AROUND IC201

SONY CDP302 NO PLAY FUNCTION. FOUND OPTICAL BLOCK STUCK AT REAR OF BU-1 UNIT.

FOUND THAT THE OPTICAL BLOCK HAD ADHERED TO RUBBER CUSHION

SONY CDP302 WILL NOT PLAY BAD CONNECTION ON C905.

SONY CDP302 SKIPS INTERMITTENTLY, TRACK 6 OR HIGHER, NOT ALWAYS IN THE SAME PLACE.

MAKE A NEW BOTTOM PANEL THAT IS DEEPER THAN THE ORIGINAL ALLOW MORE CLEARANC

SONY CDP302 DISTORTED SOUND. TRACED PROBLEM TO LOOSE PIN 41 OF IC307 (PN:CX23035)

SONY CDP302 INTERMITTENT MISTRACKING ADD A RESISTOR OF 33K OHM (1/6W 1-247-867-00) BETWEEN PIN 25 CX20108 & GROUN

SONY CDP302 INTERMITTENT SKIPPING. ADJUST RV102

SONY CDP302 INTERMITTENT PLAY, SKIPS FORWARD, BACKWARD ETC.

PERFORMED RF PLL TRACKING AND FOCUS ADJUSTMENTS

SONY CDP302 UNIT WILL NOT READ TOC, WOULD FOCUS SEARCH & THEN STOP WON'T PLAY AT ALL.

FOUND C-218 LEAKY, WHICH WOULD NOT ALLOW UNIT TO LOCATE INNER PORTION OF DIS

SONY CDP302 MISTRACKS TOWARDS END OF DISC.

IN ADDITION TO ALIGNMENT, Q203 WAS FOUND TO BE LEAKY.

SONY CDP302 SOUND DISTORTED RESOLDER PIN 41 TO BOARD OF IC307 (PN: CX23035)

SONY CDP302 WON'T PLAY REPAIR BAD CONNECTION ON C905

SONY CDP302 NOISY REPLACE C220 10MFD X 50V

SONY CDP302 INTERMITTENT OPERATION. BAD CONNECTION C905 & C952.

SONY CDP307ESD NO CHUCKING OPERATION. REPLACE THE FORMER DRIVE BELT WITH A NEW VERSION 4-917-522-02

SONY CDP310 INTERMITTENLTY WON'T READ CD

REPLACE TRAY LOADING BELT

SONY CDP310 WILL NOT READ CD MAY BE INTERMITTENT

REPLACE TRAY LOADING BELT

SONY CDP35 DOESN'T READ TOC & TRACKING IS NOT ENGAGED

REPLACE Q605 AND Q606 AND RESOLDER TRACKING COIL LEADS.

SONY CDP35 INTERMITTENT SKIPPING PROBLEM

LOOSEN THE SCREWS SECURING THE SLED RACK AND THE SLED MOTOR AND REPOSITION.

SONY CDP35 WON'T READ TABLE OF CONTENTS (TOC) & TRACKING ISN'T ENGAGED

REPLACE Q605 & Q606 & RESOLDER TRACKING COIL LEADS

SONY CDP35 MISTRACKING/SKIPS INCREASE R624 TO 6.8K

SONY CDP35 STATIC IN AUDIO ONLY WHEN MUSIC IS PLAYING ALSO UNIT MAKES TICKING SOUND.

REPLACE IC704 (PN:875930272) HM6116LPFP3 RAM .

SONY CDP35 CONSTANT LOW LEVEL ILLUMINATION OF UNUSED DISPLAY SECTIONS


SONY CDP35 INTERMITTENT NO EJECT. TENSION SPRING NEW # 1-913-796-01, LM BELT NEW # 4-914-797-01


SONY CDP350 DOOR OPENS BY ITSELF REPLACED LOADING BELT ON BOTTOM USE RCA BELT (PN: 157053)

SONY CDP390 IMTERMITTENT OR NO FOCUS SEARCH OR LD ON

REPLACE S101 (PN: 1-572-0851-1) PICKUP HOME SWITCH WHICH HAS INTERMITTENT CO

SONY CDP390 AFTER 30 MTS. SOUND FADES BECOMES STATIC & SAYS "NO DISC"

REPLACE LASER (PN: 8-848-144-11).

SONY CDP390 SOUND FADES BECOMES STATIC & SAYS "NO DISC" AFTER 30 MINUTES

REPLACE LASER (PN: 8-848-144-11)

SONY CDP391 NOISE IN AUDIO AT LOW LEVEL (SOUNDS LIKE PHONO CRACKS SNAPS & POPS)

REPLACE X251


LOOSEN THE SCREWS SECURING THE SLED RACK AND THE SLED MOTOR AND REPOSITION






SONY CDP45 INTERMITTENTLY SKIPS USUALLY ABOUT 2-3 DISC

REPLACED LASER & RF AMP (PN: 875201090)

SONY CDP45 SKIPS INTERMITTENTLY USUALLY ABOUT 2-3 DISC.

REPLACED LASER & RF AMP (PN: 875201090).

SONY CDP470 NO DISPLAY IF +30V LOW OR MISSING REPLACE IC12 (PN: 8-759-605-43) CAN USE (PN: M5231TL)




LOOSEN THE SCREWS SECURING THE SLED RACK AND THE SLED MOTOR AND REPOSTION.

SONY CDP501 EJECT IS INTERMITTENT. REPLACE DRIVE BELT. NEW # 4-917-548-02

SONY CDP510 HIGH PITCH NOISE THROUGH AUDIO WHEN PLAYING.

REPLACE RAM IC306 (PN: 8-759-802-72).

SONY CDP510 SKIPPING ON FIRST TRACK LOOSENED SLED MOTOR HOLDING SCREW AND REPOSITIONED WORM GEAR TO OPEN MESHING

SONY CDP510 DISC DOESN'T TURN OR TURNS SLOW WITH NOISE

DISC TURNTABLE IS PUSHED ALL THE WAY DOWN. LIFT THE TABLE UP A LITTLE

SONY CDP510 DISC WON'T TURN OR TURNS SLOW WITH NOISE

DISC TURNTABLE IS PUSHED ALL THE WAY DOWN LIFT TABLE UP A LITTLE

SONY CDP510 DISC OVERRUNS OR OVERRUNS REVERSELY

AFTER RELEASING THE OPTICAL BLOCK BY MOVING THE SLED GEAR A LITTLE.

SONY CDP520ES INTERMITTENTLY LOCKS UP FOUND LEAD OF TANTALUM CAPACITOR C-363 SHORTING AGAINST ANOTHER

SONY CDP520ES SKIPS BACKWARDS NEAR END OF DISC.

FLEX BOARD ON BASE UNIT SAGS & TOUCHES BOTTOM PANEL. REPAIR-BEND FLEX BOARD

SONY CDP520ES INTERMITTENT MISTRACKING ADD A RESISTOR OF 33K OHM (1/6W 1-247-867-00) BETWEEN PIN 25 CX20108 & GROUN






SONY CDP55 UNIT SKIPS ALSO TRANSFORMER BUZZING.

TIGHTEN TRANSFORMER AND CLEAN OPTICS.

SONY CDP55 MUSIC SKIPS RANDOMLY. LUBE SLIDE SHAFTS. ADJUST FOCUS BIAS. ADJUST FOCUS\TRACKING GAIN.

SONY CDP55 DOOR OPENS OR CLOSES BY ITSELF.

REMOVED CONTECT RUBBER GULE WHICH WAS CONDUCTING ON LOADING SWITCH S701

SONY CDP55 UNIT OCCASIONALLY SKIPS AT THE END OF DISC.

ADJUST GEAR MESH.


SONY CDP55 OCCASSIONALLY SKIPS AT END OF DISC

SLED MOTOR CHATTERING DUE TO POOR GEAR MESH BETWEEN WORM & FIRST GEAR

SONY CDP55 SKIPS & TRANSFORMER BUZZING

TIGHTEN TRANSFORMER & CLEAN OPTICS

SONY CDP590 IC102 REPEATEDLY FAILS IF IC102 IS DETERMINED TO BE BAD REPLACE AND TEST

SONY CDP62 MISTRACKING NOT READING DISC SOMETIMES.

LIFT BLACK COVER OFF OF LENS & SOLDER COIL CONNECTIONS OVER AGAIN.

SONY CDP620ES WON'T READ TABLE OF CONTENTS NOISY FOCUS SEARCH

REPLACED R921 1.2 OHM RESISTOR INCREASED IN VALUE FROM 1.2 OHM TO 7.6 OHM.

SONY CDP620ES WILL NOT READ TOC NOISY FOCUS SEARCH.

REPLACED R921 1.2 OHM RESISTOR INCREASED IN VALUE TO 7.6 OHM.

SONY CDP620ES INTERMITTENT MISTRACKING ADD A RESISTOR OF 33K OHM (1/6W 1-247-867-00) BETWEEN PIN 25 CX20108 TO GROU







SONY CDP650ES DRAWER WILL NOT OPEN. CHECK FOR DISC INSERTED UPSIDE DOWN.

SONY CDP650ESD INTERMITTENT MISTRACKING ADD A RESISTOR OF 33K OHM (1/6W 1-247-867-00) BETWEEN PIN 25 CX20108 & GROUN

SONY CDP670 ABNORMAL TRACKING. SUSPECTED DEAD SPOT IN SLED MOTOR. REPLACE SLED MOTOR. X-4917-504-1

SONY CDP68 NO CHUCKING OPERATION. REPLACE THE FORMER DRIVE BELT WITH A NEW VERSION 4-917-522-02


SONY CDP70 DOOR WOULD INTERMITTENTLY OPEN AND THEN CLOSE

DIRTY SWITCH (S703)

SONY CDP70 MOTOR STARTS IN THE CORRECT DIRECTION THEN REVERSES AND OVER RUNS.

REPLACE OPTICAL BLOCK ASSY.




SONY CDP790 WONT'T PLAY DISC. REPLACE BROKEN CAM. (PN: 4-933-109-01).

SONY CDP85 ERRATIC OPERATION. ADJUSTMENT OF RV101 T.E. AND RV102FE SOLVED PROBLEM.

SONY CDP9000 SCREEN BLUE AND DARK REPLACE Q703


SONY CDPC20

WHEN TURNED ON SPINDLE DROPS & CAROUSEL SPINS BUT DRAW OPENS HALF WAY/CLOSES

REPOSITION DOWN SWITCH SW105 IT IS POSITIONED TOO LOW.

SONY CDPC20 BROKEN PULLEY (CHUCKING REPLACE CHUCKING PULLEY (PN:

PULLEY) 492102201) & APPLY SOME GULE TO SECURE IT

SONY CDPC20 WHEN CHANGING FROM DISC TO DISC DRAW WILL OPEN AGAIN HALF WAY THEN CLOSE

REPOSITION DOWN SWITCH SW105 IT IS POSITIONED TOO LOW.

SONY CDPC20 BROKEN CHUCKING PULLEY REPLACE CHUCKING PULLEY (PN: 492102201) & APPLY SOME GULE TO SECURE IT

SONY CDPC211 LOCKS UP FRONT PANEL FUNCTIONS WON'T WORK

REPLACE C425 OR C432 LEAKY IN KEY SCAN INPUTS K0-K7



SONY CDPC215 DISK CONSTANTLY TURNS WHEN DISK TRAY CLOSED

REPLACE FLEX CABLE REF 63

SONY CDPC215 DISK CONSTANTLY TURNS WHEN DISK TRAY CLOSED

REPLACE FLEX CABLE REF 63

SONY CDPC301M WON'T PLAY NO FOCUS SEARCH CHECK FOR BAD SOLDER CONNECTION ON S402 SWITCH

SONY CDPC305 MISTRACKING REPLACE OPTICAL PICK UP DRIVE IC

SONY CDPC305 NO AUDIO OUTPUT WHILE DISC IS PLAYING & COUNTER IS INCREMENTING.

REPLACE LEAKY CAPACITOR C328 LOCATED ACROSS Q302.



SONY CDPC400 STATIC HEARD WHEN PLAYING REPLACE OPTICAL PICK UP ASSEMBLY





SONY CDPC500 WHEN PLAYING COUNTER JUMPS FROM 1:00 TO 1:42 & THAN PAUSE AUDIO PLAYS OK

REPLACE IC301 DIGITAL SIGNAL PROCESSOR (PN: 8-752-332-38).

SONY CDPC500 NO DISPLAY & SLOW CAROUSEL MOVEMENT

REPLACED OPEN Q903 (PN:8-729-154-83) & LEAKY D907 8-719-110-78

SONY CDPC505 SUDDENLY LOSES TRACK & STOPS INTERMITTENTLY READS TABLE OF CONTENTS

CHECK WIRES NO 1 & 18 ON CNJ301 MAY BE LOOSE



SONY CDPC5F AUDIO OUTPUT GARBLED REPLACE IC503 (PN: 8-752-320-44) IF TROUBLE REMAINS REPLACE CXD1135Q IC501

SONY CDPC70 NO MUTING WORKS DURING PROGRAM AND SHUFFLE MODE.

REOLACE MECH MICRO IC (PN:8-759-971-41).

SONY CDPC700 DISC TRAY CONTINUOUSLY ROTATES BACK & FORTH

REPLACE IC801.

SONY CDPC700 CAROUSEL INTERMITTENTLY WON'T COME OUT "E" APPEARS ON DISPLAY

REPLACE IC801

SONY CDPC705 AFTER WARMUP TRAY ERRATICALLY JOGS BACK & FORTH

RESOLDER BAD CONNECTIONS AT PIN 1 OF D701

SONY CDPC705 ERRATIC DISK CHUCKING SLOW DRAWER

REPLACE LOADING BELT NEW (PN: 4-934-388-01)

***** End of Audio database search *****

Sony Audio

Documents

Transcript of Sony Audio