.somfy.om IB+ Chronis & Soliris Smoove · Somfy is proud to present you two new ranges of...

www.somfy.com

Interactive operating instructions

Ref

. 512

9502

A

Chronis Smoove UNOChronis Smoove UNO SChronis Smoove IB+

Soliris Smoove UNOSoliris Smoove IB+

IB+

Chronis & Soliris Smoove

2/40Copyright © 2016 Somfy SAS. All rights reserved. Non contractual imagesChronis & Soliris Smoove [ Back to Contents ]


Thank you for choosing this Somfy product.

Simply elegantSomfy is proud to present you two new ranges of touch-sensitive buttons, wired, automatic controls with timeless and sleek design.

Chronis Smoove Uno and IB+ range:Time is controlled thanks to these programmable clocks for automatic opening/closing of motorized equipment (roller shutters, external venetian blinds, external blinds). These controls can be used in 3 ways: in manual mode, in automatic mode, or in simulated presence mode.

The Chronis Smoove UNO S and Chronis Smoove IB+ can be associated with an io homecontrol® sun sensor.

Soliris Smoove Uno and IB+ range:Climate is controlled thanks to an automated system for opening/closing the motorized equipment (patio awnings, interior blinds, roller shutters, external venetian blinds, external blinds) depending on sunlight or outdoor weather conditions (wind/rain). These controls can be used in 3 ways: in manual mode, in automatic mode, or in simulated presence mode.

The Soliris Smoove UNO and Soliris Smoove IB+ can be associated with an io homecontrol® sun sensor and also wired sensors (sun/light, rain, wind sensors).

The UNO versions are dedicated to control one motor.

The IB+ versions are dedicated to IB+ motor controller devices (1 to 3 channels).

Interactive operating instructionsThis full manual describes the operating instructions to make the best use of the 5 products of the new Chronis & Soliris Smoove ranges:

• Chronis Smoove UNO

• Chronis Smoove UNO S

• Chronis Smoove IB+

• Soliris Smoove UNO

• Soliris Smoove IB+

To find the common or specific functions of each product, consult the following table Functions of the 5 products : available functions of each product are indicated by a small icon.

The table of Contents presents all instructions for the 5 products. When a chapter describes a function that does not apply to all products, the concerned products are indicated in the heading of the chapter.

This manual is interactive:

• Click on each title or page number in the table of Contents to access it directly.

• Click on [ Back to Contents ] at the bottom of each page to return to table of Contents.

WELCOME PAGE



Functions of the 5 products

FeaturesChronis Smoove

UNO

Chronis Smoove UNO S

Chronis Smoove

IB +

Soliris Smoove

UNO

Soliris Smoove

IB +

TimerSnow

Rain Moon / night

TemperatureCloud

Sun / day Wind Heating

Light

Audi/Video Entry door

security Remote control

Wall mounted control

Domotique

Air conditioning

Alarm Intercom

Fire

Week program + pre-programmed days

Backlight

1 channel

1 to 3 channels

2 orders/day

4 orders/day

Presence simulation

Automatic Summer/Winter time

Sunset (in the control)

Sunrise (in the control)

Auto from

Optional settings and copy/paste with a tool

TimerSnow

Rain Moon / night

TemperatureCloud


Light




Domotique

Air conditioning

Alarm Intercom

Fire

Façade wireless io sun sensor : sun protection, sunrise & sunset

Sun sensor (wired) : sun protection, sunrise & sunset

TimerSnow

Rain Moon / night

TemperatureCloud


Light




Domotique

Air conditioning

Alarm Intercom

Fire

Rain sensor (wired only)

TimerSnow

Rain Moon / night

TemperatureCloud


Light




Domotique

Air conditioning

Alarm Intercom

Fire

Wind sensor (wired only)

PRODUCTS & FUNCTIONS

4/40Copyright © 2016 Somfy SAS. All rights reserved. Non contractual imagesChronis & Soliris Smoove


CONTENTS[ Interactive instructions ]You can click on each title to access it directly.

1. DESCRIPTION OF FUNCTIONS 51.1. UNO Versions - for controlling a 230V AC single motor 51.2. IB+ Versions - for controlling Smoove devices with IB+ input 5

2. SOFT KEY FUNCTIONS 6

3. DISPLAY 7

4. STARTING UP 84.1. Language 84.2. Time and Date 84.3. Type of End products 84.4. Runtime setup 94.5. Sun/light Sensor 104.6. Wind Sensor (Soliris versions) 114.7. Rain Sensor (Soliris versions) 124.8. End of initial settings 12

5. MANUAL MOVE COMMAND 13

6. QUICK MENU 146.1. Automatic 146.2. Auto from 146.3. Holiday mode 156.4. Manual 156.5. Settings 15

7. SETTINGS MENU 167.1. Program Timer / Cycle Times 167.2. Sun Function 217.3. Wind Function (Soliris versions) 267.4. Rain Function (Soliris versions) 287.5. Configuration in the "Normal" operating mode 307.6. Configuration in Professional Operating Mode 327.7. Additional functions in Expert Mode 37

8. TECHNICAL DATA 39



1. DESCRIPTION OF FUNCTIONS

1.1. UNO Versions - for controlling a 230V AC single motorChronis Smoove UNOAutomatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Up to two time-dependent control commands per day. Settings for the device over a backlit menu display.

Chronis Smoove UNO SAutomatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Sun- and sunset-dependent control. Up to 4 time-dependent control commands per day. Settings for the device over a backlit menu display.

Soliris Smoove UNOAutomatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Weather-dependent control (wind, rain, sun/light, and sunset). Up to 4 time-dependent control commands per day. Settings for the device over a backlit menu display.

1.2. IB+ Versions - for controlling Smoove devices with IB+ inputImportant: The settings on Chronis / Soliris Smoove IB+ Smoove devices must be matched with the installed Smoove devices. Current Smoove devices are fitted with an IB+ Bus input. Previous versions have an IB Bus input. With systems that have IB, as well as IB+ Smoove devices, the IB+ operating mode must be selected in all cases.

Chronis Smoove IB+Automatic and manual control of a motor for roller shutters, Venetian blinds or awnings. Sun- and sunset-dependent control. Up to 4 time-dependent control commands per day. Using a Chronis Smoove IB+ device, up to 100 IB/IB+ motor controller devices can be controlled. Settings for the device over a backlit menu.

Warning: All connected end products must be of the same type (e.g. all Venetian blinds).

Soliris Smoove IB+Automatic and manual control of multiple motors for roller shutters, Venetian blinds or awnings. Weather-dependent control (wind, rain, sun/light, and sunset). Up to 4 time-dependent control commands per day. Using a Soliris Smoove IB+ device, up to 100 IB/IB+ Smoove devices can be controlled. Settings for the device over a backlit menu display.

Warning: All connected end products must be of the same type (e.g. all Venetian blinds).



2. SOFT KEY FUNCTIONS

1:

- In the main display: shows the sensors activated under the line for 5 seconds

- In the settings: back to a higher menu

- In the Quick Menu: back to main display

2:

- Moves end products upwards or downwards

- For setting the function: value change, operating the cursor

- For navigating between menus

3:

- Stop function when the end product is moving

- Go to "my" Position when the end product is stopped

- Setting of "my" Position

4:

- In the main display: with a short press, go to "Quick Menu"

- In the main display: with a long press (> 2 secs.), go to "Configuration menu"

- In the settings: confirm a setting / value

4

1

2

3



3. DISPLAY

The display is fitted with a lit background. In the main menu, the display shows the time of day and, depending on the type of operation (see Chapter "Quick Menu"), the activated function (picture 1), as well as when a function is currently active (picture 2).

Stand-by-Mode:After 3 minutes without touching, the lighting on the display switches off. By touching a soft key, the lighting is activated again without setting off a command.

Main menu with activated (switched on) sensor functions (only for Chronis Smoove Uno S and Soliris).

Main display, when an automatic function, e.g. the sun function, is activated.

Sensor(s) enabled

08:231

POS.2



Important: When installing, check whether the adapter for the logic module fits (the backside of both parts is labeled). If the wrong adapter is used unintentionally, the following message is displayed: "WARNING - not compatible". The logic module or adapter hereby will not be damaged.

If the device has not been put into operation yet, you are automatically guided through the basic settings.

If the device has already been put into operation, go directly to the next chapter "Manual move command".

The basic settings are to be followed step by step:

- To go to the next sep, the configuration must be confirmed.

- Use the soft key to go back to the previous step.

4.1. Language1. Choose the display language.

2. Confirm your selection.

4.2. Time and DateTime1. Set the time / hours between 00 and 23 hrs and confirm.

2. Set the minutes and confirm.

Tip: Press longer on the soft key to change the values quicker.

Date1. Set the day and confirm.

2. Repeat to set the month and year.

Tip: Press longer on the soft key to change the values quicker.

4.3. Type of End products1. Choose the connected end product between roller shutters, awnings

and Venetian blinds.


4. STARTING UP

LanguageEnglishGerman

10:41

14 .12.15

Date

Producttyp setupRoller shutterVenetian blinds



4. STARTING UP

4.4. Runtime setupRuntime is the time a roller shutter, Venetian blind or awning requires for a complete move from moved-in position to moved-out position. Runtime is also dependent on the height of the end products and is a decisive factor for the correct moving to the intermediate positions (e.g. my-position, glare protection and sun protection).

To set runtime, there are two possibilities available: manual or automatic.

ManualTime can be set only when runtime of an end product has been determined (e.g. timed with a stopwatch).1. First set the minutes, up to 5, and confirm.

2. Then set the seconds and confirm .

AutomaticWhen runtime of the product is unknown, this can be set automatically.

Move end products upwardsThe end products must be in the top-end position. This position is given as a reference point for the exact positioning of the end products in "my" Position, glare protection or in sun protection position.

1. With the DOWN arrow, select "Start". > The end products move up.

2. When they have reached the top, select "Stop".

Setting up Runtime1. With the soft key, select "ok/menu".

2. With the DOWN arrow, select "Start". > The end products move down.

3. When the end products have reached the bottom, confirm with "ok/menu".

Runtime setupManualAutomatic

00m:15s

Manual runtime setup

Move product upStopStart

Auto runtime setupStopStart



4.5. Sun/light Sensor - The wired sun/light sensor measures the actual brightness value that the sun function

requires.

- The radio sun/light sensor measures the actual brightness value that the Sun and Sunrise/sunset Functions require.

Select the sensor between radio sensor, wired sensor or no sensor, and confirm.

Note: Not all devices provide the possibilities mentioned above. See the selection table below.

Radio sensor Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S X

Chronis Smoove IB+ X

Soliris Smoove Uno X X

Soliris Smoove IB+ X X

- With "Radio sensor", you must pair the Sunis Wirefree io with the device (see chapter "Pairing the Radio Sensor").

- With "No sensor", you can select a sensor later in the configura-tion of the Sun Functions (see chapter "Settings menu").

Warning: When the radio sensor (Sunis Wirefree io) is already paired to another device, select the "No sensor" option. You can pair the sensor later in the configuration of the Sun Functions.

Light sensor setupRadio sensorNo sensor

4. STARTING UP



4.6. Wind Sensor (Soliris versions) - The wind sensor measures the actual wind speed that the Wind Function requires.

Select the sensor between wired or no sensor, and confirm.


Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S

Chronis Smoove IB+

Soliris Smoove Uno X

Soliris Smoove IB+ X

- With "No sensor", you can select a sensor later in the configu-ration of the Wind Function (see chapter "Wind Function (Soliris versions)").

Wind sensor setupWired sensorNo sensor

4. STARTING UP



4.7. Rain Sensor (Soliris versions) - The rain sensor detects rain that the Rain Function requires.

Select the sensor between wired sensor or no sensor, and confirm.


Wired sensor

Chronis Smoove Uno

Chronis Smoove Uno S

Chronis Smoove IB+

Soliris Smoove Uno X

Soliris Smoove IB+ X

- With "No sensor", you can select a sensor later in the configu-ration of the rain function (see chapter "Rain Function (Soliris versions)").

4.8. End of initial settingsThe basic settings are now complete and the time appears in the display.

With Chronis Smoove devices, the next predefined Cycle Time also appears.

Rain sensor setupWired sensorNo sensor

10:41

08:50Sat. 20:00

4. STARTING UP



5. MANUAL MOVE COMMAND

In the main menu the following move commands can be made manually:

- UP symbol : Moves up and the symbol appears in the display.

- DOWN symbol : Moves down and the symbol appears in the display.

- "my" symbol : When the end products are moving, they are stopped. The symbol appears in the display.

When the end products are stationary, they move to the already set "my" position. In the display, the symbol appears.

Note for Venetian blinds operation:A short press on the UP symbol tilts the Venetian blinds up.

A long press on the UP symbol moves the Venetian blinds up.

A short press on the DOWN symbol tilts the Venetian blinds down.

A long press on the DOWN symbol moves the Venetian blinds down.

If you give a short press or if there is a possibility that the end products only move very slightly, adjust the start delay parameter (see "Back to Start delay").

Setting "my" PositionIn the factory state, the "my" Position is 70% set (in the case of Venetian blinds without turn). 1. Move the end products to the desired position ("my") and use the "my-soft key" to stop them.

2. Press "my-soft key" for more than 5 seconds to save the new position. > The following message appears: "My position set".

3. To delete the position, move the end products in the "my" Position.

4. Press the "my-soft key" for more than 5 seconds. > The following message appears: "My position cleared".



6. QUICK MENU

In the main menu, press shortly "ok/menu" (< 2s).

- The following mode can now be selected:

In the Quick menu, different device operating modes can be set quickly.

6.1. AutomaticWhen activated, all automatic functions are carried out. Wind and Rain Functions always have priority over Sun Functions or over timer commands. Manual operation is not possible during wind or rain alarm.

The automatic mode is set as default.

In the display, only the activated functions are shown.

Example: the next time Cycle Time will appear in the display (UP move command at 07:00).

6.2. Auto fromCurrent time +6, +12, or +18 hours: the automatic mode is switched off until this time. The automatic function can be put out of operation for a limited time.

An intentional reactivating of the automatic functions is not necessary.

Example: "Auto from 16:23" means that the automatic functions (incl. time Cycle Times) will activate the Cycle Times first from 16:23 on. The deactivating of the automatic is displayed with an arrow symbol and the time up to when the deactivation is valid.

Auto modeAuto from 16:51Auto from 22:51

Holiday modeManualSettings

10:55Mon. 16:55

10:54Thu. 07:00



6. QUICK MENU

6.3. Holiday modePresence can only be simulated when the timer is set with a fixed time. The automatic Cycle Times are randomly activated 15 minutes before or after.

The Holiday mode is displayed with a suitcase.

Example: a fixed cycle time is set for 7:00. In Holiday mode, the move commands are carried out randomly between 06:45 and 07:15. Further set functions such as sun, wind, rain, or cycle times of sunrise and sunset remain active.

6.4. ManualAll automatic functions (incl. time Cycle Times) except safety relevant functions, such as wind and rain, are deactivated.

Only the time is displayed.

6.5. Settings1. Select the appropriate mode.


See chapter "Settings menu".

10:56

10:56Mon. 16:55



7. SETTINGS MENU

In the Settings menu, the automatic functions can be set and the basic configuration of the device can be changed:

- Prog. timer

- Sun Function (only with Chronis Smoove UNO S and Soliris Smoove devices)

- Wind Function (only with Soliris Smoove devices)

- Rain Function (only with Soliris Smoove devices)

- Configuration: Language, Time, Date, Operating Mode, Display

1. In the "Quick Menu", select the menu "Settings" (see "Starting up").

2. In the main display, press the "ok/menu" soft key for more than 2 secs.

7.1. Program Timer / Cycle TimesEach day, two (with Chronis Smoove UNO, Cycle Time 1 to Cycle Time 2), or four different timer commands (with Chronis Smoove UNO S and Soliris Smoove devices, Cycle Time 1 to Cycle Time 4) can be carried out. A timer command activates a move of the end products (e.g. a downward move in the evening or an upward move in the morning). As a rule, the end products require two Cycle Times per day (e.g. morning up and evenings down).

The timer commands can depend on either the time or on Sunrise/sunset.

Factory settingsWith all Chronis and Soliris Smoove devices, Cycle Times 1 and 2 are already set and switched on:

- Cycle Time 1: switched on, UP command, Mon-Fri at 7:30, Sat-Sun at 8:30

- Cycle Time 2: switched on, DOWN command every day at 20:00

1. Confirm the "Prog. Timer" function to carry out timer commands.

2. Select the Cycle Time (depending on model, 1 to 2 or 1 to 4) and confirm.

Switching ON/OFFYou can switch the function on and off.1. Confirm the function.

2. Switch the function on or off with the DOWN or UP arrow.

Configuration menuProg. timerSun Function

Configuration menuWind FunctionRain Function

Configuration menuRain FunctionConfiguration

Prog. timerCycle Time 1Cycle Time 2

Cycle Time 1ON/OFF Cycle Time Configuration

Cycle Time 1OFFON



7. SETTINGS MENU

Configuration of Cycle TimesThe Cycle Times are defined with the Position, Day, Time (Time or depending on Sunrise/sunset).

Go to the "Configuration" sub menu. You will be guided to the next step.

PositionSelect the required position of the end products on the timer between the following possibilities and confirm the position.

- Up (top), Down (bottom)

- Glare protection (not with Chronis Smoove Uno): mostly used in connection with sun automatism

- Intimacy (not with Chronis Smoove Uno): mostly evenings when one does not wish to be seen

- my Position: a position freely definable by the user, also acces-sible over the my soft key

- Position 2 (not with Chronis Smoove Uno): a second position definable by the user

The Glare protection and Intimacy positions are programmed with preset values but they can also be changed (see "Configuration of Cycle Times").

Glare protection Intimacy

Roller shutters 70% 90%

Venetian blinds 100%, angle 0.5s 100%, angle 0s

Awnings 100% 100%

Note for Venetian blinds operation:100% position means that the Venetian blinds move completely downwards.

Angle 0.5s means that the blinds, after moving downwards, move again upwards for 0.5 seconds and thus tilt out the slats.

Cycle Time 1ON/OFF Cycle Time Configuration

Cycle Time 1UpDown

Cycle Time 1Glare protectionIntimacy

Cycle Time 1my PositionPosition 2



DayDetermine on which day the end products should move to the selected position.

• Select between the following options and confirm your selection:

- Week: the cycle time is sent every day at the same time

- Mon - Fri: the cycle time is sent from Monday to Friday at the same time

- Sat - Sun : the cycle time is sent from Saturday to Sunday at the same time

- Mon, Tues, Wed, Thurs, Fri, Sat, Sun: the cycle time is sent individually each day

Setting TimeDetermine at what time the cycle times are activated.

1. With the arrow, select the following option and confirm.

2. Select the time and confirm.

3. Set the minutes and confirm.

Setting Time depending on Sunrise/sunsetDetermine whether the Cycle Time should be activated at sunrise (sun symbol), or at sunset (moon symbol) instead of a fixed time.

Chronis Smoove UNO has been programmed only with sunset.

1. With the arrow, select the following option and confirm.

2. Press the "back" soft key to quit and save the time setting.

07:30

--:--

Cycle 1 - Up

WeekMon.-Fri.

07:30

08:30

Cycle 1 - Up

Sat.-Sun.Mon.-Fri.

20:00

20:00

Cycle 1 - Down

Sun.Mon.

12:00

12:00

Cycle 1 - Up

Mon.-Fri.Week

12:00

Cycle 1 - UpWeekMon.-Fri.

12:00

Cycle 1 - UpWeekMon.-Fri.

7. SETTINGS MENU



Setting of the Sunrise/sunset functionThe Surise/sunset function parameter is now set in the "Prog Timer" menu.1. In "Prog Timer", go to the sub menu "Sunrise/Sunset" (directly after

"Cycle Time 2" with Chronis Smoove UNO, or "Cycle Time 4" with all other devices).

2. Confirm. > The sub-menus "Sunrise" and "Sunset" appear.

The Sunrise/sunset function offers two options: the Cosmic Option and the Sensor Option.

With the Cosmic Option, the controller activates the Cycle Time corresponding to the calculated sunrise and sunset.

With the Sensor Option, the Cycle Time activates the brightness measured on the radio sensor. The Sensor Option is only available when the radio sensor is applied.

3. Select the radio sensor. > Both options (Sensor/Cosmic or Cosmic settings) are displayed.

4. Select the desired option in the "Sensor/Cosmic" menu and confirm your selection.

Setting of the Sensor Parameter (only with application of the Radio Sensor)Note: Only for Chronis S and Soliris.

Two setting options are available:

- Threshold: confirm the threshold value between 1 and 10 for the sunset. The default value is 5 and corresponds to a typical sunset value of approx. 200 Lux.

- "Not before time" with sunrise, and "Not after time" with sun-set: the Cycle Time is activated with sunrise, but not before a set time. With sunset, the Cycle Time is not activated after the defined time. Set the desired time and confirm.Setting of the

Prog. timerCycle Time 4Sunrise - sunset

Sunrise - SunsetSunrise settingsSunset settings

Sunrise settingsSunrise typeCosmic settings

Sensor settingsThresholdNot before time

Sunrise typeSensorCosmic

0

Threshold

07h:00m

Not before time

7. SETTINGS MENU



Cosmic settingsTwo setting options are available:

- DeviationTime: the Cycle Time is activated at sunrise or sunset with a settable time diffe-rence between -2 and +2 hours. In each case, it can be set for sunrise and sunset. The time difference applies for all Cosmic move commands. Determine the desired difference time and confirm.

Example: at 05h08, the sunset is activated. The timer will activate a Cycle Time at 21h00 (see main display). If you find this time to be too early, you can enter a difference time of +10 mins so that the Cycle Time is activated at 21h10. The difference time will be the same for each day.

- "Not before time" with sunrise and "Not after time" with sunset: the Cycle Time is activated at sunrise and not before the set time. With sunset the Cycle Times are activated not later than a certain time. Set the desired time and confirm.

Display of next move command over TimerWhen the "Prog. Timer / Cycle time x" function is set and switched on, the next Cycle Time is displayed with Day, Time and Move command.

Example: at sunset, a move to the Intimacy position.

When the function is active, the following is displayed.

Example: Friday at 20h00, DOWN command.

Cosmic settingsDeviation timeNot before time

00h:10m

Deviation time

21h:00m

Not after time

09:03Fri. Pos.16:30

Fri. 20:00

7. SETTINGS MENU



7.2. Sun FunctionNote: Only for Chronis S and Soliris.

The Sun Function is a comfort function: it stops the sun glaring and the heating up of the room in summer.

As soon as the measured sun value exceeds the set threshold value for at least 3 continuous minutes, the end products move to the predefined position.

When the threshold value is not exceeded for at least 15 continuous minutes, the Sun Function is deactivated and the end products move to the upper end position.

For test purposes, the delay times can be shortened (see "Configuration in Professional Operating Mode").

• Under "Configuration menu", select "Sun function".

> If you have already selected a sensor at start-up, these setting options are displayed.

> If you have selected "No sensor" at start-up, you will be guided automatically to Sensor configuration (see "Configuration of the Sun Sensor").

Switching ON/OFFYou can switch the function "ON" or "OFF".

1. Select "ON or "OFF" to switch on or off the function.


Note: In the factory state, the Sun Function is switched off.

Configuration menuProg. timerSun Function

Sun FunctionON/OFFThreshold

Sun FunctionActual levelPosition

Sun FunctionPositionConfiguration

Sun sensor ON/OFFOFFON

7. SETTINGS MENU



ThresholdNote: First go to the "Sun sensor actual level" menu to display the actual measured value and to set the threshold value (see "Actual level").

1. Confirm the function.

2. With the UP/DOWN arrow, set the threshold value from 1 to 10.

1 2 3 4 5 6 7 8 9 10

5 to 10 kLux

10 to 16 kLux

16 to 22 kLux

22 to 27 kLux

27 to 33 kLux

33 to 38 kLux

38 to 44 kLux

44 to 49 kLux

49 to 55 kLux

> 55 kLux

3. Confirm the value.

Actual level The actual value is displayed (from 1 to 10).

Leave the menu with the soft key or ok/menu button.

PositionThe target position is set to the value the end products should have after exceeding the threshold value.

Factory settingsThe Glare protection and Intimacy positions are already saved with values and can be changed (see "Configuration in Professional Operating Mode").

- Roller Shutters: Glare protection: = Position 70%, Intimacy = 90%

- Venetian blinds: Glare protection: = Position 100%, Angle 0.5s , Intimacy = 100% Angle 0.0s.

- Awnings: Glare protection: = Position 100%

1. Select the position between Glare protection, Intimacy, my-Position, and Position 2.

2. Confirm.

We recommend selecting "Glare protection".

5

Sun sensor threshold

6

Sun sensor actual level

Sun sensor positionGlare protectionIntimacy

Sun sensor positionmy PositionPosition 2

7. SETTINGS MENU



Configuration of the Sun SensorYou can configure the sun sensor.1. Select between the wired sensor (only possible with Soliris devices),

radio sensor (only possible with Chronis Smoove UNO S, Chronis Smoove IB+ or Soliris Smoove devices), or no sensor.


For "Radio sensor", see "Back to Pairing the Radio Sensor".

Pairing the Radio SensorPairing the Radio Sensor with a Smoove device

1. Confirm "Radio sensor" and "Pairing".

2. Press on the program button of the Sunis WireFree io, until the green LED lights up.

3. Confirm "Start". > The following message appears: "Searching for wireless sun sensor..." . > After a short time, the following message appears: "Wireless sun sensor connected" and the

LED on the Sunis Wirefree io blinks.

4. If the message "No wireless sun sensor found" appears:

• Check the distance between the sensor and the device.

• The sensor might already be paired with another device. In this case, reset the Sunis Sensor: press the program button of the Sunis WireFree io for 7 seconds until the green LED blinks. Repeat the pairing procedure.

ConfigurationWired sensorRadio sensor

PairRadio sensor

Read key

PairStopStart

PROGRAM BUTTON GREEN LED

7. SETTINGS MENU



Pairing a Radio Sensor with two or three Smoove devicesThe Sunis WireFree io radio sensor can be paired with a maximum of three Smoove devices (Smoove Chronis Uno/IB+ and Soliris devices). The procedure for the first Smoove device is carried out as explained above ("Back to Pairing the Radio Sensor with a Smoove device"). For additional Smoove devices, a key transfer from the already paired device must be done.

Key transfer1. With the already paired Smoove device (device 1), go to "Configuration

menu" / "Sun Function" / "Configuration" and confirm "Radio sensor".

2. Select "Share key".

3. Confirm "Start". > The following message appears: "Wating for key sharing...".

4. (Device 2) Go directly to "Configuration menu" / "Sun Function" / "Configuration" and confirm "Radio sensor".

5. Select "Read key" and confirm. > The following message appears: "Requesting wireless key...". > When the transfer is successful, the following message appears

in the display of device 2: "Key request finished". The following message appears in the display of device 1: "Key sharing finished".

Device 2 must now be paired with the radio sensor (see "Back to Pairing the Radio Sensor with a Smoove device").

A third Smoove device can be paired with the same procedure (Key transfer).

ConfigurationWired sensorRadio sensor

Remove light sensoRadio sensor

Share key

StopShare key

Start

PairRadio sensor

Read key

Read keyStopStart

7. SETTINGS MENU



Display of Sun Function on screenWhen the function is set and switched on, "Sensor(s) enabled" is displayed.

• Press on the "Back" arrow. > The Sun symbol appears.

When the Sun Function is active (threshold value exceeded), the sun symbol is shown on the main display during the cycle time delay (3 minutes).

After the cycle time delay, the end products move to the preset position. The sun symbol and the desired position are displayed during the move.

Subsequently, the sun symbol appears again, but smaller.

If the threshold value is not exceeded, the sun symbol blinks during the switching-off time delay (15 minutes). After the time delay, the end products move to the upper-end position. The sun symbol and the UP arrow are displayed during the move.

Note: The sun function is temporarily deactivated when a manual request is made (up, down, my).

The sun function will resume operation with the next change in status of the sun (appears or desappears).

Sensor(s) enabled

10:23

10:24

10:24

POS.

7. SETTINGS MENU



7.3. Wind Function (Soliris versions)The Wind Function is a safety function that protects the end products in high-wind speeds against damage.

When the wind speed exceeds the threshold value for more than 2 seconds, the end products move to the upper-end position.

When the threshold value is not exceeded for more than 15 minutes, the manual operation, sun automatic and the timer are then all released again.

Warning: The Wind Function must be activated deliberately.

• Under "Configuration menu", select "Wind Function".

> The following options are available.

If you have selected "No sensor" at start-up, you will be guided automatically to sensor configuration (see "Back to Configuration of the Wind sensor").

Switching ON/OFFYou can switch the functions on and off.1. Confirm the selection.

2. Select "ON" or "OFF".

3. Confirm.

Note: In the factory state, this function is switched off.

Configuration menuSun FunctionWind Function

Wind FunctionON/OFFThreshold

Wind FunctionActual levelConfiguration

Wind sensor ON/OFF

OFFON

7. SETTINGS MENU



Wind sensor thresholdWe recommend at first to go to "Wind Sensor actual level" to measure the actual real value beforehand (see "Back to Actual level") and next to set the threshold value.

1. Confirm this function.

2. Set the threshold value from 1 to 10 with the UP/DOWN arrow.

1 2 3 4 5 6 7 8 9 10

5 to 11 km/h

11 to 17 km/h

17 to 23 km/h

23 to 29 km/h

29 to 35 km/h

35 to 41 km/h

41 to 47 km/h

47 to 53 km/h

53 to 59 km/h

> 60 km/h

Actual levelLeave the menu with the soft key or ok/menu button.

Configuration of the Wind sensorThe wind sensor can be configured again.1. Select between the wired sensor and no sensor.


Display of the Wind Function on screenWhen the function is set and switched on, "Sensor(s) enabled" is displayed.

• Press on the "Back" arrow. > The wind symbol appears.

When the Wind Function is momentarily active (threshold exceeded), the end products move immediately to the upper-end position, and the wind symbol and the UP arrow appear during the move.

Subsequently, the wind symbol appears again in the main display.

When the threshold value is not exceeded, the wind symbol blinks in the main display window during the switching-off time delay (15 minutes).

5

Wind sensor threshold

6

Wind sensor actual level

Sensor(s) enabled

10:45

Wind sensor setupWired sensorNo sensor

10:45

7. SETTINGS MENU



7.4. Rain Function (Soliris versions)The Rain Function is a safety function that protects the end products against damage due to rain.

When raining, the end products move to the upper-end position.

When there is no rain for more than 15 minutes, the manual operation, sun automatic and the timer are all released again.

Warning: The Rain Function must be activated deliberately.

• Confirm the function.

> The following options are available.

If you have selected "No sensor" at start-up, you will be guided automatically to sensor configuration (see "Back to Configuration of the rain sensor").

Switching ON/OFFYou can switch the functions on and off.1. Confirm the selection.

2. Select "ON" or "OFF".

3. Confirm.

Note: In the factory state, this function is switched off.

Actual levelThis menu showns whether rain has been detected by the sensor.

With this function, the wiring and functionality of the rain sensor can be checked.

Leave the menu with the soft key or ok/menu button.

Configuration menuWind FunctionRain Function

Rain FunctionON/OFFActual condition

Rain FunctionActual conditionConfiguration

Rain sensor ON/OFFOFFON

Rain sensor actual level

not active

7. SETTINGS MENU



Configuration of the rain sensorThe rain sensor can be configured again. 1. Select between the wired sensor and no sensor.


Display of the Rain Function on screenWhen the function is set and switched on, "Sensor(s) enabled" is displayed.

• Press on the "Back" arrow. > The rain symbol appears.

As soon as the rain sensor detects rain, the end products move to the upper-end position and the rain symbol appears.

When rain is no longer detected, the rain symbol blinks during the switching-off time delay (15 minutes).

Rain sensor setupWired sensorNo sensor

Sensor(s) enabled

11:21

11:23

7. SETTINGS MENU



7.5. Configuration in the "Normal" operating modeThe User mode is set to "normal" in the factory state and the following options are available.

• Under "Configuration menu", select "Configuration".

LanguageSee "Language".

TimeSee "Time and Date".

DateSee "Time and Date".

User mode setupThe User mode is set by default on "Normal". In the professional mode, all further options such as Runtime, End product, Position and Service are displayed (see "Configuration in Professional Operating Mode").

Configuration menuRain FunctionConfiguration

Configuration LanguageTime

Configuration DateUser mode

Configuration User modeDisplay

User mode setup NormalProfessional

7. SETTINGS MENU



DisplayYou can set the brightness and contrast of the display.

• Confirm the menu "Display".

Brightness1. With the arrow, change the current value between 1 and 10.

2. Select and confirm your preference.

Contrast1. With the arrow, change the current value between 1 and 10.

2. Select and confirm your preference.

5

Brightness

Display BrightnessContrast

5

Contrast

7. SETTINGS MENU



7.6. Configuration in Professional Operating ModeWhen confirming the Professional Operating Mode, the following additional functions are shown in "Configuration menu" and "Configuration".

Time and automatic Daylight saving time1. Set the time.

2. Activate (ON) or deactivate (OFF) the automatic Daylight saving time change-over (ON).


Runtime See "Runtime setup".

End Product See "Type of End products".

ServiceFactory Settings

The device can be reset to the factory state.


2. Confirm your selection. > On confirmation, the following message appears; "All configuration

data will be erased".

3. With the soft key button "Ok/Menu", confirm reset. > Start-up starts automatically (see "Starting up"). You can cancel

the step with the button.

Demo ModeThe time delays with the Sun / Wind / Rain Functions are shortened for test purposes (minutes are seconds).


2. Confirm your selection. > The demo mode is active for 30 minutes.

Daylight saving time OFFON

ServiceFactory resetDemo mode

Factory resetNoYes

Demo modeOFFON

7. SETTINGS MENU



Positions Depending on the controlling, Glare protection, Intimacy, my-Position and Position 2 can be set.1. Select the corresponding position.

2. Confirm.

Note: For all positions, the same procedure can be repeated.

PositionUnder "Glare protection value set", you can set the position.

1. Set the position of the end products in percent (0% top, 100% bottom).

2. Confirm.

TiltNote: Only with Venetian blinds.

Under "Glare protection tilt set", you can set the angle.

1. Set the angle in seconds (0.0 seconds minimum, 3 seconds maximum).

2. Confirm:

TestUnder "Glare protection test", you can check the set position.1. Select "Yes".

2. Confirm. > The end products move to the set position.

PositionsGlare protectionIntimacy

Glare protectionPositionTest

Glare protectionPositionTilt

Positionsmy PositionPosition 2

70%

Glare protection value set

0.5s

Glare protection tilt set

Glare protection testNoYes

7. SETTINGS MENU



IB+ Mode (not with UNO versions) Chronis and Soliris Smoove IB+ can control several Smoove IB+ or other IB+ devices at the same time over the IB+ Bus channel. The list of the Smoove devices is in the chapter "IB/IB+ Versions - for controlling Smoove devices with IB/IB+ input".

In addition, Chronis and Soliris Smoove IB+ can control the Smoove devices in up to 3 different zones (see "Multiple Zone Control"). This enables e.g. the controlling of Smoove devices at different cycle times.

Note: Requirement for multiple zone control: You need the QuickCopy device and the corresponding PC software.

Initializing the IB+ Smoove devices In the IB+ mode, the IB+ Smoove devices must be initialized with certain parameter settings such as Runtime. The initialization ensures that the IB+ Smoove devices are connected together with the Chronis / Soliris Smoove IB+ on the IB+ channel.

1. Under "Configuration" / "IB Mode", select "IB+".

2. Confirm your selection. > Several data telegrams are sent to the IB+ Smoove devices. > The following message appears briefly: "Please wait". The LEDs

of the IB+ Smoove device light up in red for a short time. > At the same time, the UP relay is activated whereby the end

products move to the upper end position (system reset).

Multiple Zone ControlChronis / Soliris Smoove IB+ can control up to 3 different zones over the IB+ control channel.

For multiple zone control, you need the QuickCopy device and the corresponding PC-software.

Number and Configuration of Zones using QuickCopy softwareYou can only configure the zones with the QuickCopy PC Software.

Refer to the "QuickCopy" operating instructions.

IB modeIBIB+

Configuration PositionsIB mode

IB+ initializationNoYes

7. SETTINGS MENU



Assigning Zones In the assignment, you define which IB+ Smoove device belongs to which zone. The assigning is done directly on the Soliris / Chronis Smoove IB+.

Note: Requirement: The Smoove device is connected with the Soliris / Chronis Smoove IB+. The Soliris / Chronis Smoove IB+ must be set to "Professional mode" (see "Configuration in Professional Operating Mode").

1. Under "Configuration menu" / "Configuration", confirm "Zones".

2. Select the zone (zone 1 to 3) to which the IB+ Smoove device should be assigned.

Defining the Assignment1. Confirm the "Add device" option, then "Start".

> The LED on the Smoove Uno IB+ lights up alternatingly in green, orange and red to show that the device is currently in the "Pairing mode".

> With animeo IB+ Smoove devices, the 4 LEDs flash alternatingly.

2. To confirm assignment of the zone, press the UP or DOWN button of the Smoove uno IB+, or the UP or DOWN button of the IB+ Smoove device that is currently connected.

> The pairing mode in the corresponding zone is confirmed with a move command of the motor.

> The LED no longer lights up.

Delete Assignment1. Under "Zones", select the corresponding zone.

2. Confirm the option "Remove device".

3. Repeat the step as with "Back to Defining the Assignment".

Configuration IB modeZones

Select zone Zone 1Zone 2

Zone 1Add deviceRemove device

7. SETTINGS MENU



Manual Operation of a ZoneOn the Soliris / Chronis Smoove IB+, the number of zones appears on the right.

1. Press the OK-Menu button in the main display to go to "Quick Menu". > The "Select zone" option appears.

2. Select the corresponding zone operation. > The selection is now always taken into account with manual

operation.

3. Confirm and select the zone to be operated. > You can now set off a move command in this zone only.

Note: When a move command is set off, the zone appears in the display next to the move direction symbol.

4. Go to the Quick Menu to check which zone is being operated. > The zone being operated appears in the first menu point ("Zone

Operation 1" for the operation of Zone 1 or "Zone Operation 1-3" for the operation of all zones).

Mon.13:09

20:00

12

3

Zone 1Add deviceRemove device

Select zoneAll zonesZone 1

1

Confirm zone 1Remove deviceAuto from 19:10

7. SETTINGS MENU



7.7. Additional functions in Expert ModeExpert Mode enables access to the special functions and is used only in exceptional cases.

• In the main menu, press the "Back" button for more than 7 seconds. > A message appears: "You have switched on the Expert Mode". > As soon as the device goes in Stand-By Mode, you leave the Expert Mode.

Under "Configuration Menu " / "Configuration", you can set additionally the functions "Start delay" and "Max. tilting time".

Start delay With electronic motors, the electrical current does not often immediately set off a mechanical move (wake-up time). Depending on the manufacturer, this time can vary between 0.3 and 0.7 secs. With Somfy WT motors, this time is set generally 0.3 secs.


2. Set the value between 0.0 and 2.5 secs.


Max. tilting time (with Venetian blinds)With Venetian blinds, in addition to the runtime of the end products, the tilting time of the slats is set. The tilting time is the time the slats require for a maximum move before the blinds begin to move upwards. This time consists usually of between 0.8 to 2.0 secs and is dependent on type of blinds and motor manufacturer.


2. Set the value between 0.0 and 3.0 seconds.


Configuration Start delayProducttyp setup

Configuration Max. tilting timeProducttyp setup

0.1s

Start delay

3.0s

Max. tilting time

7. SETTINGS MENU



Software versionUnder "Configuration menu" / "Configuration" / "Service", you have access to the following information.

1. Confirm to read the current version.

2. Press on the button or on the ok/menu button to exit the menu again.

Number of counter-up or counter-down movements

1. Confirm the corresponding option to read the number of close steps of the Up-relay or of the Down-relay.

2. To leave the menu, press "Back" or "OK".

ServiceFactory resetSoftware version

Software version

Rev: 1163 modified

ServiceCounter-up movemCounter-down mov

7

Counter-up movements

0

Counter-down movements

7. SETTINGS MENU



8. TECHNICAL DATA

Operating voltage 230V AC 50/60 Hz

Operating temperature 0°C to +40°C

Protection type IP20

Protection class II

Relays 230V AC ~ 3A cos φ 0,9

Storage temperature -10°C / +65°C

Display 17 mm x 35 mm, backlit

Somfy hereby declares that the radio equipment covered by these instructions is in compliance with the requirements of Radio Directive 2014/53/EU and the other essential requirements of the applicable European Directives.The full text of the EU declaration of conformity is available at www.somfy.com/ce.

Somfy SAS50 avenue du Nouveau MondeF-74300 CLUSESFRANCE

www.somfy.com

Som

fy S

AS, c

apita

l 20.

000.

000

Euro

s, R

CS A

nnec

y 30

3.97

0.23

0 -

11/2

016

.somfy.om IB+ Chronis & Soliris Smoove · Somfy is proud to present you two new ranges of...

Documents

Transcript of .somfy.om IB+ Chronis & Soliris Smoove · Somfy is proud to present you two new ranges of...