Solidfix
-
Upload
benztooling -
Category
Engineering
-
view
119 -
download
0
Transcript of Solidfix
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ Solidfix® and BENZ CAPTOTM Modular Quick Tool Change Systems
Powered by theSee Machining from a New Angle benztooling.com/quickchange
What Is Wrong With This Picture?
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Injuries Like This Are Avoidable!
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Slow Set-Up Procedures
ER Collets Take Time to Loosen,
Remove the Tool and Collet
Then Exchange with the Next
Collet and Tool. The Tool
Length Offset Must Be Set with
the Lathe Tool Pre-setter. A Radial Tool Can Take 20 –
30 Minutes to Install in the
Turret and Accurately Set Up.
Standard Radial Alignment is
Time Consuming and Must Be
Done with Every Tool Change
by Tightening and Loosening
Two Set Screws.
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Implement Quick Change Processes
Use BENZ Solidfix® Quick Change Live Tools Where
You Can Preset the Adapters and Leave the Tools
Mounted Permanently in the Turret.
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Implement Quick Change Processes
Use BENZ Solidfix® Quick Change Live Tools to
Reduce 2 – 3 Hour Set Ups to 5 – 10 Minutes!
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Implement Quick Change Processes
Start by Leaving
the Tools in the Turret!
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Implement Quick Change Processes
• Change Only
the Adapters.
• Exchange 12 Tools
in Less Than 3 Minutes!
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ Solidfix® The Safe, One-handed
15-Second Solution
• Speed
• Power
• Performance
• Flexibility
• Safety
• Fast Return on Investment
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ Solidfix® Live Tools
Modular Design Allows for Fast Tool
Changes in 10 – 15 Seconds and
Safe, One-Handed Operations
Powered by theSee Machining from a New Angle benztooling.com/quickchange
• Weldon for Parallel
Shanks DIN 1835B
• Whistle-Notch for Parallel
Shanks DIN 1835 E
• Shrink Fit Chucks
• Softsynchro® with IC
Reduce Cost of Ownership
• Collet Chucks 8° Type ER
• Milling Machine Arbors with IC
• Closing Plug
• Test Arbors
• Boring Bar Blanks
• Special Tool Options
One BENZ Solidfix® Could Replace the Need for up to Ten Live Tools
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ Solidfix® Adapter
Self-Centering Taper
Bayonet Style Lock
Thick Face Contact
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ Solidfix® Adapter
Bayonet Lock
Self-Centering Taper
Full Face Contact
Powered by theSee Machining from a New Angle benztooling.com/quickchange
The Assembly Block Can Be Used to
Assemble and Tighten the Tools in the
BENZ Solidfix Adapter, Allowing for Fast
Tool Exchanges for Worn or Broken Tools.
Presetting the BENZ Solidfix® Adapter
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Presetting the BENZ Solidfix® Adapter
BENZ Solidfix Adapters Can Be
Easily Preset Using a Height Gauge
and the BENZ Solidfix Assembly
Block.
Preset Tools Can Be Exchanged in
10 – 15 Seconds.
Powered by theSee Machining from a New Angle benztooling.com/quickchange
1. 10 -15 Second Tool Change
2. Live Tool Left Mounted in the Turret Between Set Ups
3. No Need for Live Tools with Costly Dedicated Spindles
4. Safe One-Handed Operation
5. Easy Integration of Preset Tooling
6. Reduce Setup Time from Hours to Minutes
7. Fast and Easy Set Up and Teardown Between Batch Runs
BENZ Solidfix® Payback
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ CAPTO™ VB24 Turret
• BENZ CAPTO™ for
Axial & Radial Live Tools
(Standard or Shaped Profile)
• BENZ CAPTO™ Static Bolt on
Tools for the VB24 Turret
Powered by theSee Machining from a New Angle benztooling.com/quickchange
BENZ CAPTO™ BMT Style
Axial & Radial Combination
Bolt on Static Tooling
Axial Radial
Powered by theSee Machining from a New Angle benztooling.com/quickchange
Contact Us Directly For Questions
BENZ Inc. 704.529.5300
www.benztooling.com
8325 J Arrowridge Blvd.
Charlotte, NC 28273
Rapid Turnaround to Minimize Downtime• BENZ Inc.’s Standard Repair Service
Turnaround is Two Weeks
• Choose Expedite Service to Replace
Worn or Damaged Tools within 72 hours
• Preventive Maintenance Program is
Available to Minimize Unscheduled Downtime
• One-Year Warranty on all Repairs