Solar panel manufacturing process
-
Upload
aster-e-technologies -
Category
Engineering
-
view
195 -
download
4
Transcript of Solar panel manufacturing process
Aster e Technologies
Solar PV Module Manufacturing ProcessPRESENTED BY :- Mr. SHIVAJI R Shinde
SOLAR PV PANEL MANUFACTURING MACHINE
Semi Automatic Manufacturing Process
Aster E Technologies
www.
aste
rete
ch.c
om
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
Aster E Technologies
INTRODUCTION TO MANUFACTURING PROCESS
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
Aster E Technologies
Introducing Solar PV Module Manufacturing Machines CELL TESTER
Solar Cell Tester is applied to the primary process of solar Panel manufacturing, testing parameters like :
Electrical testing: Electrical performance of photovoltaic cells under a solar simulator.
Quality testing: surface quality, breakages, cracks... A computer with user-friendly software caters for different options, such as defining the parameters to be measured.
LASER SCRIBING
scribing or cutting the Solar Cells and Silicon Wafers in solar PV industry, including the mono crystalline silicon and poly crystalline silicon solar cells and silicon wafer
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
Aster E Technologies
RIBBON CUTTER
SOLDRING TABLE
The Ribbon Cutting machine is used to cut the ribbon as per dimensions by manually.
Soldering Table is used to solder the cell by using ribbon in a single cell that is called Tabbing and solder the tabbed cell is called Stringing
TABBING AND STRIGINGSemi Automatic Manufacturing Process
Aster E Technologies
www.
aste
rete
ch.c
om
The solar Tabber and Stringer machine is a fully automatic machine for solder photovoltaic solar cells. This equipment is one of the first step in the production line and it’s one of the most important in the entire pv module production line. Assembling and soldering strings of cells interconnected with metal ribbons usingthe Tabber & Stringer.
Aster E Technologies
www.
aste
rete
ch.c
omSemi Automatic Manufacturing Process
GLASS WASHER
Wash, rinse and dry the glass superstrate using a glass washer. It remove unwanted particles from glass and dry very fast
LAY UP STATIONManual place the tempered glass, EVA, Solar cell string and back sheet five layer materials together on this station .Completing the module laminate circuit by soldering bus ribbons to connect the strings together and provide output leads at the busing station.
EL TESTERIn this machine detects the micro cracks in the prepared solar module
MIRROR OBSERVATION
Mirror observation method is use to observe solar module clearly, to check the foreign particles in the module and strings alignment
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
Aster E Technologies
LAMINATOR
In the manufacturing line for pv modules, the laminator machine is of fundamental importance in curing the EVA, to join the layers that form the module and remove all air from between them. When the materials in the photovoltaic module have been placed on the glass, they undergo a heat treatment that converts the EVA into a type of gel that encapsulates all the layers to form a very strong and compact sandwich. The result is a high quality product ready for the finishing phase before testing and installation. To make the service even faster and more complete, accessory units are available for the semi automatic preparation of the glass, the sheets of EVA and the back sheet
Aster E Technologies
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
SUN SIMULATOR
This equipment is used in the final test of solar module manufacturing. It measures solar module output power and physical parameter by simulate sunlight, and classifies them according to the results of measurement. The test result can save and label on the solar module.
Aster E Technologies
Semi Automatic Manufacturing Processww
w.as
tere
tech
.com
FRAMING
The solar panel Framing machine is one of process in the solar panel production line
Completing final assembly, which includes edge trimming at the Trimming station, installing and edge gasket and frame with the Frame Assembly and attaching a junction box at the JB station.
Semi Automatic Manufacturing Process
SUPPORTING EQUIPMENT
www.
aste
rete
ch.c
om
Aster E Technologies
www.
aste
rete
ch.c
om
Aster E Technologies
Automatic Dual Track Tabber & Stringer CHD150-M2600
LAYUP STATION
www.
aste
rete
ch.c
om
Aster E Technologies
Semi Automatic Manufacturing Process
Aster E Technologies
www.
aste
rete
ch.c
om
ALL FABRICATION EQUIPMENTS
We have customers all over INDIA
Contact Us
Aster e Technologies
Tel: +91 889 243 1790 +91 988 096 2111Fax: +91 80 416 10311
www.asteretech.com Email: [email protected]: aetsales5
Address: 1,Mahesh Building, Chamundeswari Layout, Doddabommasandra, Vidyaranyapura Main Road, Bangalore – 560097 Karnataka, India.