SOAP/LOTION DISPENSER INSTALLATION -...
6
Turn off water supply. REQUIRED TOOLS: PARTS INCLUDED: Adjustable Wrench Optional Caps - Soap, Lotion and Finish (TRADITIONAL MODELS ONLY) COUNTER OR SINK 1-3/8” HOLE A B C F G D E 1. 2. 3. 4. 5. 6. 7. BEFORE YOU BEGIN YOUR INSTALLATION: 41180 Raintree Court • Murrieta, CA 92562 1-888-304-0660 • 951-304-0520 www.waterstoneco.com VEN-038-SOAP Rev. B SOAP/LOTION DISPENSER INSTALLATION Contemporary Model # 4065 Traditional Model #s 4055, 4060 Slide the brass spacer ring up to top of dispenser shroud, then thread the clamp nut. Tighten nut snug to underside of sink or counter. Add soap or lotion to plastic bottle. Thread bottle (E) into bottom of dispenser shroud. Pull and remove spout (A) from dispenser body (B). Remove clamp nut (C) and brass spacer ring (D) from threaded shroud. Slide red tubing (F) into tube fitting (G) at bottom of spout. Insert open end of red tubing down through dispenser and into plastic bottle. Push down on spout to secure over white O-rings. Pump spout a few times to get soap or lotion flowing. Fit dispenser body through 1-3/8” hole on counter or sink. (No plumbers putty is required. O-ring seals base).
Transcript of SOAP/LOTION DISPENSER INSTALLATION -...
Turn o� water supply.
REQUIRED TOOLS: PARTS INCLUDED:
Adjustable Wrench
Optional Caps - Soap, Lotion and Finish(TRADITIONAL MODELS ONLY)
COUNTEROR SINK
1-3/8”HOLE
A
B
C
F
G
D
E
1. 2. 3. 4.
5. 6. 7.
BEFORE YOU BEGIN YOUR INSTALLATION:
41180 Raintree Court • Murrieta, CA 925621-888-304-0660 • 951-304-0520www.waterstoneco.com VEN-038-SOAP Rev. B
SOAP/LOTION DISPENSER INSTALLATIONContemporary Model # 4065
Traditional Model #s 4055, 4060
Slide the brass spacer ring up to top of dispenser shroud, then thread the clamp nut. Tighten nut snug to underside of sink or counter.
Add soap or lotion to plastic bottle. Thread bottle (E) into bottom of dispenser shroud.
Pull and remove spout (A) from dispenser body (B). Remove clamp nut (C) and brass spacer ring (D) from threaded shroud.
Slide red tubing (F) into tube fitting (G) at bottom of spout.
Insert open end of red tubing down through dispenser and into plastic bottle.
Push down on spout to secure over white O-rings. Pump spout a few times to get soap or lotion flowing.
Fit dispenser body through 1-3/8” hole on counter or sink. (No plumbers putty is required. O-ring seals base).
Turn o� water supply.
REQUIRED TOOLS: PARTS INCLUDED:
1. Adjustable Wrench 2. Phillips Screwdriver
USM1375Undersink Mounting Hardware(1-1/4”)
AIR SWITCH INSTALLATIONContemporary Model # 3010Traditional Model # 4010
B
A
G
H
J
C
GARBAGE DISPOSAL
D
F
ECOUNTEROR SINK
1-1/2”HOLE
1. 2. 3. 4.
5. 6. 7.
Slide washer and thread the clamp nut onto threaded shroud. Tighten nut snug to underside of sink or counter.
Securely tighten clamp screws (G).
Remove clamp nut (A) and washer (B) from threaded shroud (C).
Slide clear tubing (D) into tube fitting (E) at bottom of air switch.
Slide other end of clear tubing (H) into tube fitting at bottom of control box (J).
Plug control box into undersink electrical outlet. Garbage disposal can be plugged into either dual outlet.
Fit air switch (F) through 1-1/2” hole on counter or sink. (No plumbers putty is required. O-ring seals base).
BEFORE YOU BEGIN YOUR INSTALLATION:
41180 Raintree Court • Murrieta, CA 925621-888-304-0660 • 951-304-0520www.waterstoneco.com VEN-038-AIRSW Rev. B
Turn o� water supply.
REQUIRED TOOLS: PARTS INCLUDED:
1. Adjustable Wrench 2. Phillips Screwdriver
USM1375Undersink Mounting Hardware(1-1/4”)
A
B
C
D
E
F
Optional Button Caps - Logo and Finish(TRADITIONAL MODELS ONLY)
DUAL PORT AIR GAP INSTALLATIONContemporary Model # 3030Traditional Model # 4030
BEFORE YOU BEGIN YOUR INSTALLATION:
4030
A. Dual Port Air GapB. Drainage Hose*C. Intake Hose*D. DishwasherE. Brine Discharge Hose*F. Reverse Osmosis Filtration Unit
*Not Included 3030
41180 Raintree Court • Murrieta, CA 925621-888-304-0660 • 951-304-0520www.waterstoneco.com VEN-038-DPAG Rev. C
G
H
LM
K
J
A
D
E
C
B
F
1-1/2”HOLE
1. 2. 3. 4.
5. 6.
DUAL PORT AIR GAP INSTALLATIONContemporary Model # 3030Traditional Model # 4030
Unscrew and remove top clamp nut (D) from both threadings on piping. Slide gasket (E) off piping and remove.
Pull air gap (A) off of upper cap nut (B). Unscrew and remove cap nut from piping (C).
Slide gasket down and screw top clamp nut back onto piping. Adjust the two clamp nuts to fit countertop thickness. (No plumbers putty is required).
Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. Be sure to have overflow holes (F) facing sink.
From underneath counter top, fit air gap piping upward through 1-1/2” hole.
Slide small intake hose (G) over small connector. Slide larger drainage hose (H) over large connector. Tighten hose clamps.
Third intake hole (J) has 3 options. Use hose connector (K) for additional dishwasher, use filtration hose connector (L) for reverse osmosis unit, or use solid cap (M) to plug third hole.
Turn o� water supply.
REQUIRED TOOLS: PARTS INCLUDED:
1. Adjustable Wrench 2. Phillips Screwdriver
USM1375Undersink Mounting Hardware(1-1/4”)
A
B
C
D
Optional Button Caps - Logo and Finish(TRADITIONAL MODELS ONLY)
41180 Raintree Court • Murrieta, CA 925621-888-304-0660 • 951-304-0520www.waterstoneco.com
SINGLE PORT AIR GAP INSTALLATIONContemporary Model # 3020Traditional Model # 4020
BEFORE YOU BEGIN YOUR INSTALLATION:
4020 3020
A. Dual Port Air GapB. Drainage Hose*C. Intake Hose*D. Dishwasher
*Not Included
VEN-038-SPAG Rev. B
A
B
D
E
F
GH
1. 2. 3.
4. 5. 6.
1-1/2”HOLE
SINGLE PORT AIR GAP INSTALLATIONContemporary Model # 3020Traditional Model # 4020
Unscrew and remove top clamp nut (D) from both threadings on piping. Slide gasket (E) off piping and remove.Pull air gap (A) off
of upper cap nut (B). Unscrew and remove cap nut from piping (C).
Slide gasket down and screw top clamp nut back onto piping. Adjust the two clamp nuts to fit countertop thickness. (No plumbers putty is required).
Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. Be sure to have overflow holes (F) facing sink.
Slide small intake hose (G) over small connector. Slide larger drainage hose (H) over large connector. Tighten hose clamps. Turn on water supply and check for leaks.
From underneath counter top, fit air gap piping upward through 1-1/2” hole.
41180 Raintree Court • Murrieta, CA 925621-888-304-0660 • 951-304-0520www.waterstoneco.com VEN-038-SPAG Rev. B
