Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation...
-
Upload
lizette-humpherys -
Category
Documents
-
view
212 -
download
0
Transcript of Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation...
![Page 1: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/1.jpg)
Snowflake Coasters
NOISE LEVEL 1
Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue gun Production cost worksheet
Directions:1. Listen to the manager read the task sheet.2. Review the steps on the picture walk before you
begin.3. Following the picture walk, complete the steps
to make a snowflake coaster.4. When you are done, clean up your area. Wash
the sponge brush thoroughly so that it can be reused.
5. Put your coasters in a safe place to dry.6. Complete the production cost worksheet.7. Put your finished worksheet in the completed
rotation basket when you are done.
PBL Connection: Becoming an Entrepreneur
I can add, subtract, multiply and divide decimal numbers.Standard 5.NBT.7
I can make precise measurements and specify the units.Standard SC 5.5.1
![Page 2: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/2.jpg)
Snowflake Coasters
Name _____________________
Directions: Complete the calculations to determine the production cost per coaster.
Show all work. Expenses:
Fabric 5.99Sanders 5.94Spray Paint 3.984 x 4 “ Tiles 8.00High Gloss Coating 5.99Modge Podge 4.99
Total snowflake coasters produced = 50
Per product cost = ________
Suggested retail price for a set of 4 coasters = _______
I can add, subtract, multiply and divide decimal numbers.Standard 5.NBT.7
![Page 3: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/3.jpg)
Step 1: Sand all the rough edges off of the tile with the sander.
Step 2: Wipe off all the dust with the damp cloth.
TIP: Make sure your work space is free of dust after you are done sanding your tile.
![Page 4: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/4.jpg)
Step 3: Measure the width at 4 ¼ inches. Measure the height at 4 ¼ inches.
TIP: Remember to work from the edge of the fabric to conserve your materials.
Step 4: Draw a line marking the edges of the square you measured.
![Page 5: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/5.jpg)
Step 5: Use your scissors to cut out your square.
Step 6: Use hot glue to put glue down around the edges of the tile and a large x in the middle of the tile. Place the felt onto the tile and smooth it out so that it lies flat.
TIP: Be careful not to burn yourself! You can use a ruler to smooth out the felt onto the tile if you don’t want to touch the felt with your
hands.
![Page 6: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/6.jpg)
Step 7: Gather your materials to place the snowflake onto your coaster.
Step 8: Use the sponge brush to brush a fine layer of Modge Podge onto the top of the tile.
TIP: Place a piece of foil under your tile to create a workspace. You will keep your coaster on the foil until it dries and the final step is
completed.
![Page 7: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/7.jpg)
Step 9: Center the snowflake on the tile.
TIP: Make sure that everyone places their snowflake on their tile in the same position as yours. These four tiles will make one
coaster set!Step 10: Brush a heavy layer of Modge Podge onto the top of the tile and the snowflake. Cover this space thoroughly! Be careful not to move your snowflake as you brush it.
![Page 8: Snowflake Coasters NOISE LEVEL 1 Materials Ruler Pencil Fine tip marker Felt 4 tiles per rotation Modge Podge Foil Sponge brush Sander Damp cloth Hot glue.](https://reader035.fdocuments.in/reader035/viewer/2022070306/55178d585503463e368b554d/html5/thumbnails/8.jpg)
Step 11: Your completed tile should look similar to the one pictured below.
Last step: Your finished product will look like this when it dries!
TIP: Keep your tile on the foil somewhere safe in your classroom until it is completely dry. Mrs. Spear will spray all the tiles with a
water resistant sealant before you assemble the coasters for sale.