Smart Slaves
Transcript of Smart Slaves
Smart Slaves
Remote I/O Terminals with Transistors
DRT2-ID08(-1)/OD08(-1)/MD16(-1)MIL Connector Terminals with Transistors
DRT2-ID16ML(-1)/OD16ML(-1)/ID16MLX(-1)/OD16MLX(-1)Environment-resistive Terminals with Transistors (without detection functions)
DRT2-ID04CL(-1)/OD04CL(-1)/ID08CL(-1)/OD08CL(-1)/MD16CL(-1)/HD16CL(-1)
OMRON CorporationIndustrial Automation Company
Control Devices Division H.Q.
Shiokoji Horikawa, Shimogyo-ku,Kyoto, 600-8530 JapanTel:(81)75-344-7109Fax:(81)75-344-7149
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD HoofddorpThe NetherlandsTel:(31)2356-81-300/Fax:(31)2356-81-388
Authorized Distributor:
Note: Specifications subject to change without notice. Cat. No. R110-E1-05Printed in Japan1006-0.3M
OMRON ELECTRONICS LLC
1 East Commerce Drive, Schaumburg,IL 60173 U.S.A.Tel:(1)847-843-7900/Fax:(1)847-843-8568
OMRON ASIA PACIFIC PTE. LTD.
83 Clemenceau Avenue,#11-01, UE Square,Singapore 239920Tel:(65)6835-3011/Fax:(65)6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,200 Yin Cheng Zhong Road,PuDong New Area, Shanghai, 200120 ChinaTel:(86)21-5037-2222/Fax:(86)21-5037-2200
Note: Do not use this document to operate the Unit.
Printed on 100% Recycled Paper
Remote MaintenanceThe lineup now includes a wide variety of Smart Slaves with different numbers of control points that contribute to production site servicing and repair.
Operating time monitor error or contact operation count monitor error
2 3
OMRON's DRT2-series Smart Slaves do not just input and output ON/OFF signals. They collect a variety of value-added information to help increase the rate of operation without changing the wiring for existing DeviceNet networks. In particular, they allow the separation of control systems and maintenance systems so that maintenance systems can be created independently of control systems.
PLC
Configurator
Control I/O
DRT2-series Smart Slave
Pneumatic valve (Connected device comment)
Maintenance information
Easy-to-view Display2
3Sensor (Connected device comment)
Cylinder (Connected device comment)
Control System Maintenance SystemMaintenance SystemControl System
Operating time, contact operation counter
Machine Operation Monitored by Slave
Faster Maintenance Work1
Use production site information in a variety of applications, such as maintenance and quality control.
The Slave can hold comments, allowing quick identification of fault locations and faulty devices.
The Slave Unit represents machine operating time and operational changes as data, enabling monitoring without increasing the load between controllers.
By counting the number of ON/OFF operations and the total operating time, the Slave Unit can provide notification when maintenance is required.
Measuring Counting
Maintenance is required for cylinder 23A in inspection line A!
All data can be converted to electronic format and, by combining with an OMRON PLC (CS/CJ Series), checked directly from Ethernet or the Internet to allow remote maintenance.
Information monitoring for each Slave
Collect a variety of data from maintenance systems without influencing control systems and productivity.
Using OMRON Temperature Input Terminals for Maintenance
Slave comment
Status confirmation using the status icon
Unit conduction time monitor error
Communications power voltage monitor error
If it takes too long to modify the ladder program on the Master when a Temperature Sensor is replaced:
Slaves internally
convert display values
to temperature input
values so the Controller
program no longer has
to be modified to
perform this task.
Short Startup
If prolonging the time it takes to reach a certain temperature may degrade equipment:
The operating time of a preset temperature range is counted in 1-s units.
The peaks or valleys of temperature inputs that change in a regular pattern
are counted to predict when devices operating with severe temperature
swings are due for maintenance.
Failure Prediction
and Maintenance
Sensor replaced by one with a different input range
Operating time
Indicator service life control
Time
Input
Semiconductor manufacturing equipment
Tem
per
atu
re
Scaling performed inside the Slave
Slaves can notify the Master when a setting is exceeded.
Scaling points for 0% and 100% are set from the Configurator
Maintenance SystemMaintenance SystemControl SystemControl System
DRT2-series Smart Slave
DeviceNet Configurator
Ethernet
Maintenance informationPLC
Control information
Unit conduction
time monitor
(See note.)
Operating time
monitor
External load
short-circuit detection
Contact operation
counter (See note.)
I/O power status
monitor
Communication error
history monitor
Network power
voltage monitor
Note: The contact operation counter function and the unit conduction time monitor function cannot be used simultaneously.
Operating time monitor
Contact operation counter
Unit conduction time monitor
Slave and connected component comments
I/O power status monitor
Reliable equipment
startup
Preventive maintenance
of equipment
Reduced startup time
Reduced downtime
It's time for
motor
maintenance!
What is the
present
communications
voltage?
The cylinder's
speed is
incorrect!
It might be time
for a switch
inspection!
Is the I/O
power supply
turned ON?
What was the
cause
of the error?
Communication error history monitor
Network power voltage monitor
The wiring to
the I/O device is
short-circuited
or broken!
Operating time monitor error or contact operation count monitor error
2 3
OMRON's DRT2-series Smart Slaves do not just input and output ON/OFF signals. They collect a variety of value-added information to help increase the rate of operation without changing the wiring for existing DeviceNet networks. In particular, they allow the separation of control systems and maintenance systems so that maintenance systems can be created independently of control systems.
PLC
Configurator
Control I/O
DRT2-series Smart Slave
Pneumatic valve (Connected device comment)
Maintenance information
Easy-to-view Display2
3Sensor (Connected device comment)
Cylinder (Connected device comment)
Control System Maintenance SystemMaintenance SystemControl System
Operating time, contact operation counter
Machine Operation Monitored by Slave
Faster Maintenance Work1
Use production site information in a variety of applications, such as maintenance and quality control.
The Slave can hold comments, allowing quick identification of fault locations and faulty devices.
The Slave Unit represents machine operating time and operational changes as data, enabling monitoring without increasing the load between controllers.
By counting the number of ON/OFF operations and the total operating time, the Slave Unit can provide notification when maintenance is required.
Measuring Counting
Maintenance is required for cylinder 23A in inspection line A!
All data can be converted to electronic format and, by combining with an OMRON PLC (CS/CJ Series), checked directly from Ethernet or the Internet to allow remote maintenance.
Information monitoring for each Slave
Collect a variety of data from maintenance systems without influencing control systems and productivity.
Using OMRON Temperature Input Terminals for Maintenance
Slave comment
Status confirmation using the status icon
Unit conduction time monitor error
Communications power voltage monitor error
If it takes too long to modify the ladder program on the Master when a Temperature Sensor is replaced:
Slaves internally
convert display values
to temperature input
values so the Controller
program no longer has
to be modified to
perform this task.
Short Startup
If prolonging the time it takes to reach a certain temperature may degrade equipment:
The operating time of a preset temperature range is counted in 1-s units.
The peaks or valleys of temperature inputs that change in a regular pattern
are counted to predict when devices operating with severe temperature
swings are due for maintenance.
Failure Prediction
and Maintenance
Sensor replaced by one with a different input range
Operating time
Indicator service life control
Time
Input
Semiconductor manufacturing equipment
Tem
per
atu
re
Scaling performed inside the Slave
Slaves can notify the Master when a setting is exceeded.
Scaling points for 0% and 100% are set from the Configurator
Maintenance SystemMaintenance SystemControl SystemControl System
DRT2-series Smart Slave
DeviceNet Configurator
Ethernet
Maintenance informationPLC
Control information
Unit conduction
time monitor
(See note.)
Operating time
monitor
External load
short-circuit detection
Contact operation
counter (See note.)
I/O power status
monitor
Communication error
history monitor
Network power
voltage monitor
Note: The contact operation counter function and the unit conduction time monitor function cannot be used simultaneously.
Operating time monitor
Contact operation counter
Unit conduction time monitor
Slave and connected component comments
I/O power status monitor
Reliable equipment
startup
Preventive maintenance
of equipment
Reduced startup time
Reduced downtime
It's time for
motor
maintenance!
What is the
present
communications
voltage?
The cylinder's
speed is
incorrect!
It might be time
for a switch
inspection!
Is the I/O
power supply
turned ON?
What was the
cause
of the error?
Communication error history monitor
Network power voltage monitor
The wiring to
the I/O device is
short-circuited
or broken!
Wide variety of control and maintenance functions using DeviceNet.
4 5 6
DeviceNet Configurator
DRT2-ID16(-1)
DRT2-OD16(-1)
DRT2-ID08(-1)
DRT2-OD08(-1)
DRT2-MD16(-1)
Settings and monitoringfor startupSettings and monitoring for maintenance
DRT2-ROS16
DRT2-ID16S(-1)
DRT2-MD16S(-1)
DRT2-AD04/DRT2-AD04H
DRT2-DA02
DRT2-TS04T
DRT2-TS04P
DRT2-ID08C(-1)
DRT2-OD08C(-1)
DRT2-HD16C(-1)
I/O Control and Maintenance
Sensor Input and Maintenance Monitor Control and MaintenanceAnalog Control and Maintenance
E5ZN-DRT3G3MV-PDRT2 (for 3G3MV Series)
3G3RV-PDRT2 (for 3G3RV Series)
DRT2-ID32ML(-1)
DRT2-OD32ML(-1)
DRT2-MD32ML(-1)
DRT2-ID16ML(-1)
DRT2-OD16ML(-1)
DRT2-ID16MLX(-1)
DRT2-OD16MLX(-1)
DRT2-ID16TA(-1)
DRT2-OD16TA(-1)
DRT2-MD16TA(-1)DRT2-ID04CL(-1)
DRT2-OD04CL(-1)
DRT2-ID08CL(-1)
DRT2-OD08CL(-1)
DRT2-MD16CL(-1)
DRT2-HD16CL(-1)
DRT2-WD16CL(-1)
Monitor network devices using
a DeviceNet Configurator.
PLC
CS/CJ-series
DeviceNet Unit
DRT2-ID32SL(H)(-1)
DRT2-OD32SL(H)(-1)
DRT2-MD32SL(H)(-1)
DRT2-ID32B(-1)
DRT2-OD32B(-1)
DRT2-MD32B(-1)
DRT2-ID32BV(-1)
DRT2-OD32BV(-1)
DRT2-MD32BV(-1)
Board Terminals
with MIL Connectors
Remote I/O Terminals with
Screw-less Clamps
e-CON Connector Terminals Analog I/O TerminalsTemperature Input
TerminalsDeviceNet Communications
Unit for E5ZN Digital
Temperature Controllers
DeviceNet Communications
Units/Cards for Inverters
Remote I/O Terminals
with Transistors
Remote I/O Terminal
with Relay Outputs
Environment-resistive
Terminals with Transistors
(with detection functions)
Remote I/O Terminals
with 3-tier Terminal Blocks
MIL Connector
Terminals
Environment-resistive
Terminals with Transistors
(without detection functions)
Collect a variety of data from maintenance systems without influencing control systems and productivity.Communications power supply voltage monitor, deterioration due to aging, operating time data, and other information can be easily collected and managed via the network. Locations of problems can be easily identified.
Single action
Models with 8 Input,8 Output, or 16 I/O PointsAdded to the Lineup
Remote I/O Terminals with IP67 High Environmental Resistance
Terminals with 16 Inputs or Outputs
Remote I/O Terminals
with Transistors
DRT2-ID08(-1)/OD08(-1)/
MD16(-1)
Environment-resistive Terminals
with Transistors
DRT2-ID04CL(-1)/OD04CL(-1)/
ID08CL(-1)/OD08CL(-1)/MD16CL(-1)/
HD16CL(-1)/WD16CL(-1)
MIL Connector Terminals
with Transistors
DRT2-ID16ML(-1)/
OD16ML(-1)/
ID16MLX(-1)/
OD16MLX(-1)
First Board-type Smart Slave TerminalsUser boards attach easily to the DRT2- D32V(-1) using screws.
Wiring is completed in a single action.No screw tightening required.Removable terminal blocks.Advanced models detect ground faults and broken lines in I/O wiring.Applicable wire sizes range from AWG24 to AWG16 (0.2 to 1.25 mm2 dia.)
Includes industry-standard e-CON connector that can be used to connect prewired sensors without using special tools. (The OMRON XN2 Connector can be used.)
The DRT2-AD04H offers high resolution at 1/30,000 (full scale) and insulation between input channels.The DRT2-AD04 and DRT2-DA02 support a wide variety of data sampling function, including scaling, peak/bottom hold, top/valley hold, comparator, integral, and differential operation functions.
Offers basically the same functions as Analog Input Terminals, such as scaling and comparators.Also provides functions that are available only from Temperature Input Terminals, such as the time in a preset temperature range and temperature difference detection between input channels.
Monitoring and setting of Temperature Controller from PLC.Batch download of all Temperature Controller parameters from Configurator.
Frequencies and other specifications can be designated from PLC.Monitor-related maintenance possible, including output current (torque) error detection/trace, operation monitor, and general-purpose I/O read.
I/O points can be extended by adding Expansion Units.
One-step relay exchangeOperation time monitor function enabled by combining Remote I/O Terminals with Expansion I/O Units.
High resistance to environments (IP67).Detecting shorts in the sensor power supply is also possible.
The 3-tier Terminal Block means that wiring locations are easy to find with no wiring to intermediate terminals. Ultra-small 32-point remote
terminals (35 x 60 x 80 mm (W x D x H)).
Smart Slave functions provide robust support for effective maintenance and monitoring device operation status. The terminals conform to IP67 and use materials selected for resistance to oil and spattering. Models with two-output connector are also available to improve ease of connection with hydraulic valve devices.
Connection with an array of I/O interfaces is achieved by combining adaptor boards for D-Sub or other interfaces.
7 DRT2-series Smart Slave DRT2-series Smart Slave 8
Functions Supported by Smart Slaves
: Yes, ---: No
Note: The contact operation count monitor and the total RUN (ON) time monitor cannot be used at the same time for one contact. External load detection is supported only by the DRT2-MD32SLH-1 and DRT2-OD32SLH-1.
Function
Slave name
General-purpose Slaves General-purpose Slaves Environment-resistive SlavesGeneral-
purpose SlavesAnalog Slaves
Remote I/O TerminalsMIL Connector
TerminalsBoard Terminals Screw-less Clamp Terminals Environment-resistive Terminals e-con
ConnectorTerminals
Analog I/O TerminalsTemperatureInput TerminalsType Models with Transistors Model with
Relay OutputsModels with 3-tierTerminal Blocks
Models withTransistors
Models with MIL Connectors
Models with TransistorsWith Detection Functions
Models with TransistorsWithout Detection Functions
Models with TransistorsWith Detection Functions
Models with TransistorsWithout Detection Functions
ModelDRT2-@D16(-1)
DRT2-@D08(-1)
DRT2-MD16(-1)
DRT2-ROS16
DRT2-@D16TA(-1)DRT2-@D32ML(-1)DRT2-@D16ML(-1)DRT2-@D16MLX(-1)
DRT2-@D32B(-1)DRT2-@D32BV(-1)
DRT2-@D32SLH(-1) DRT2-@D32SL(-1)DRT2-@D08C(-1)DRT2-@D16C(-1)
DRT2-@D04CL(-1)DRT2-@D08CL(-1)DRT2-@D16CL(-1)
DRT2-@D16S(-1)
DRT2-AD04
DRT2-AD04H
DRT2-DA02
DRT2-TS04@
I/O classification Input Output Input OutputInput/output
Output Input OutputInput/output
Input OutputInput/output
Input OutputInput/output
Input OutputInput/output
Input OutputInput/output
Input Output Input OutputInput/output
InputInput/output
Input Output Input
Operating time monitor (Inputs and outputs only)
--- --- --- --- ---
Contact operation count monitor --- ---
Unit conduction time monitor
Total RUN (ON) time monitor --- ---
Unit comment
Connected device comment
Network power voltage monitor
I/O power status monitor --- --- --- ---
Communications error history monitor
Input filter --- --- --- --- --- --- --- --- --- --- --- ---
Prevention of malfunctions due to sensor inrush current
--- --- --- --- --- --- --- --- --- --- --- ---
Sensor power short-circuit detection --- --- --- --- --- --- --- ---
External load short-circuit detection --- --- --- --- (See note.) --- --- --- --- --- ---
Sensor disconnection detection --- --- --- --- --- --- --- --- ---
External load disconnection detection --- --- --- --- --- --- --- --- ---
Removable terminal blocks --- --- --- ---
Automatic baud rate detection
Unit power supply wiring not required
Power supply wiring not required for input devices
--- --- --- --- --- --- ---
Expansion I/O Units mountable --- --- --- --- --- --- --- --- ---
Scaling --- --- --- --- --- ---
User calibration --- --- --- --- --- ---
Last maintenance date
Integral function --- --- --- --- --- ---
Moving average processing --- --- --- --- --- --- ---
Number of AD conversion points setting (conversion cycle)
--- --- --- --- --- --- --- ---
Peak/bottom hold --- --- --- --- --- --- ---
Top/valley hold --- --- --- --- --- --- ---
Change rate calculations --- --- --- --- --- --- ---
Comparator function --- --- --- --- --- --- ---
Setting output value for errors --- --- --- --- --- --- --- ---
Top/valley count --- --- --- --- --- --- ---
Operating time in a preset temperature range
--- --- --- --- --- --- ---
Temperature difference detection between input channels
--- --- --- --- --- --- ---
DRT2-Series Smart Slave 9
Specifications
Communicationspower supply voltage
11 to 25 VDC (supplied from communications connector)
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC −15% to +10%)
Noise immunity Conforms to IEC61000-4-4, 2 kV (power lines)
Vibration resistance 10 to 60 Hz, 0.7-mm double amplitude, 60 to 150 Hz, 50 ms2 for 80 min each in the X, Y, and Z directions
Shock resistance 150m/s2, 6 directions, 3 times each
Dielectric strength 500 VAC (between isolated circuits)
Insulation resistance 20 MΩ min. (between isolated circuits)
Ambient operatingtemperature
−10 to 55°C
Ambient operatinghumidity
25 to 85%
Ambient operatingatmosphere
No corrosive gases
Ambient storagetemperature
−20 to 65°C
Degree of protection IP67
Mounting methodDRT2-@D08@-1@/@D16(-1): 35-mm DIN Track DRT2-@D32ML(-1)/@D16ML(-1): 35-mm DIN Track DRT2-@D04CL(-1)/@D08CL(-1)/@D16CL(-1): M5 screws mounting (front or back)
Screw tighteningtorque
DRT2-@D08(-1)/@D16(-1): M3 (power supply and I/O terminals): 0.3 to 0.5 N·mDRT2-@D32ML(-1)/@D16ML(-1): M2 (communications connector screws): 0.26 to 0.3 N·m,
M3 (screw terminals): 0.3 to 0.5N·mDRT2-@D04CL(-1)/@D08CL(-1)/@D16CL(-1): Round connectors (communications connector, power supply, and I/O): 0.39 to 0.49 N·m
M5 (Unit mounting from the front): 1.47 to 1.96 N·m
10 DRT2-Series Smart Slave
Input Specifications
Remote I/O Terminals with TransistorsTerminals with 8 Inputs
Terminals with 8 Inputs/8 Outputs
MIL Connector Terminals with Transistors Terminals with 16 Inputs, with Connectors
Standard Environment-resistive Terminals and Environment-resistive Terminals with Transistors
Terminals with 4 Inputs
Terminals with 8 Inputs
Terminals with 16 Inputs
Terminals with 8 Inputs/8 Outputs
Item Model DRT2-ID08(-1)
Input current 6.0 mA max. per point at 24 VDC
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
ON voltageNPN 15 VDC min. (between each input terminal and V)
PNP 15 VDC min. (between each input terminal and G)
OFF voltageNPN 5 VDC max. (between each input terminal and V)
PNP 5 VDC min. (between each input terminal and G)
OFF current 1.0 mA max.
Isolation method Photocoupler isolation
Input indicator Yellow LED indicator
Item Model DRT2-MD16 DRT2-MD16-1
Internal I/O common NPN PNP
Number of I/O points 8 inputs
ON voltage15 VDC min. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
5 VDC min. (between each input terminal and G)
OFF current 1 mA max.
Input current6.0 mA max. per point at 24 VDC3.0 mA max. per point at 17 VDC
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
8 points per common
ItemModel DRT2-ID16ML
DRT2-ID16MLXDRT2-ID16ML-1DRT2-ID16MLX-1
Internal I/O common NPN PNP
Number of I/O points 16 inputs
ON voltage17 VDC min. (between each input terminal and V)
17 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF current 1 mA max.
Input current6.0 mA max. per point at 24 VDC3.0 mA max. per point at 17 VDC
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Max. number of simultaneous ON input points
16
Number of points per common
16 points per common
Item Model DRT2-ID04CL DRT2-ID04CL-1
Internal I/O common NPN PNP
Number of I/O points 4 inputs
ON voltage15 VDC min. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
5 VDC min. (between each input terminal and G)
OFF current 1 mA max.
Input current6.0 mA max. per point at 24 VDC3.0 mA max. per point at 17 VDC
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
4 points per common
Item Model DRT2-ID08CL DRT2-ID08CL-1
Internal I/O common NPN PNP
Number of I/O points 8 inputs
ON voltage15 VDC min. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
5 VDC min. (between each input terminal and G)
OFF current 1 mA max.
Input current6.0 mA6.0 mA max. per point at 24 VDC3.0 mA max. per point at 17 VDC
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Number of points per common
8 points per common
Item Model DRT2-HD16CL DRT2-HD16CL-1
Internal I/O common NPN PNP
Number of I/O points 16 inputs
ON voltage15 VDC min. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF currrent 1 mA max.
Input current6.0 mA max. per point at 24 VDC3.0 mA max. per point at 17 VDC
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
16 points per common
Item Model DRT2-MD16CL DRT2-MD16CL-1
Internal I/O common NPN PNP
Number of I/O points 8 inputs
ON voltage15 VDC min. (between each input terminal and V)
15 VDC min. (between each input terminal and G)
OFF voltage5 VDC max. (between each input terminal and V)
5 VDC min. (between each input terminal and G)
OFF currrent 1 mA max.
Input current6.0 mA max. per point at 24 VDC3.0 max. per point at 17 VDC
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 1.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
8 points per common
DRT2-Series Smart Slave 11
Output Specifications
Remote I/O Terminals with TransistorsTerminals with 8 Outputs
Terminals with 8 Inputs/8 Outputs
MIL Connector Terminals with TransistorsTerminals with 16 Outputs, with Connectors
Note: Make sure the total external load current does not exceed 2 A.Make sure that the V and G terminals do not exceed 1 A per terminal.
Standard Environment-resistive Terminals and Environment-resistive Terminals with Transistors
Terminals with 4 Outputs
Terminals with 8 Outputs
Terminals with 16 Outputs
Terminals with 8 Inputs/8 Outputs
Item Model DRT2-OD08(-1)
Rated output current 0.5 A per point, 4.0 A per common
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Residual voltage 1.2 V max.
Leakage current 0.1 mA max.
Isolation method Photocoupler isolation
Output indicator Yellow LED indicator
Item Model DRT2-MD16 DRT2-MD16-1
Internal I/O common NPN PNP
Number of I/O points 8 outputs
Rated output current 0.5 A per point, 4 A per common
Residual voltage1.2 V max. (0.5 A DCbetween each outputterminal and G)
1.2 V max. (0.5 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
8 points per common
ItemModel DRT2-OD16ML
DRT2-OD16MLXDRT2-OD16ML-1DRT2-OD16MLX-1
Internal I/O common NPN PNP
Number of I/O points 16 outputs
Rated output current 0.3 A per point, 2 A per common (See note.)
Residual voltage1.2 V max. (0.3 A DCbetween each outputterminal and G)
1.2 V max. (0.3 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
16 points per common
Item Model DRT2-OD04CL DRT2-OD04CL-1
Internal I/O common NPN PNP
Number of I/O points 4 outputs
Rated output current 0.5 A per point, 4 A per common
Residual voltage1.2 V max. (0.5 A DCbetween each outputterminal and G)
1.2 V max. (0.5 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
4 points per common
Item Model DRT2-OD08CL DRT2-OD08CL-1
Internal I/O common NPN PNP
Number of I/O points 8 outputs
Rated output current 0.5 A per point, 4 A per common
Residual voltage1.2 V max. (0.5 A DCbetween each outputterminal and G)
1.2 V max. (0.5 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
8 points per common
Item Model DRT2-WD16CL DRT2-WD16CL-1
Internal I/O common NPN PNP
Number of I/O points 16 outputs
Rated output current 0.5 A per point, 4 A per common
Residual voltage1.2 V max. (0.5 A DCbetween each outputterminal and G)
1.2 V max. (0.5 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
16 points per common
Item Model DRT2-MD16CL DRT2-MD16CL-1
Internal I/O common NPN PNP
Number of I/O points 8 outputs
Rated output current 0.5 A per point, 4 A per common
Residual voltage1.2 V max. (0.5 A DCbetween each outputterminal and G)
1.2 V max. (0.5 A DCbetween each outputterminal and V)
Leakage current 0.1 mA max.
I/O power supply voltage 20.4 to 26.4 VDC (24 VDC, −15 to +10%)
ON delay time 0.5 ms max.
OFF delay time 1.5 ms max.
Number of points percommon
8 points per common
12 DRT2-Series Smart Slave
Internal Circuit Configuration
Remote I/O Terminals with TransistorsDRT2-ID08 (NPN) DRT2-ID08-1 (PNP)
DRT2-OD08 (NPN) DRT2-OD08-1 (PNP)
DRT2-MD16 (NPN) DRT2-MD16-1 (PNP)
Photocoupler
Photocoupler
Inte
rnal
circ
uits
V 24 VDC
0
1
G
Phy
sica
lla
yer
Communicationsconnector
DC-DCConverter
(non-insulated)
V+
CAN H
DRAIN
CAN L
V−
Photocoupler
Photocoupler
Inte
rnal
circ
uits
V 24 VDC
0
1
G
Phy
sica
lla
yer
DC-DCConverter
(non-insulated)
V+
CAN H
DRAIN
CAN L
V−
Communications connector
Photocoupler
Inte
rnal
circ
uits
0
1
G
V 24 VDC
Phy
sica
lla
yer
DC-DCConverter
(non-insulated)
CAN H
DRAIN
CAN L
Vol
tage
step
dow
n
Communications connector
V+
V−
Photo-coupler
Photocoupler
Inte
rnal
circ
uits
0
1
G
Photocoupler
V 24 VDC
Phy
sica
lla
yer
DC-DCConverter
(non-insulated)
V+
CAN H
DRAIN
CAN L
V−
Vol
tage
step
dow
n
Communicationsconnector
Photocoupler
0
1
G2
V2 24 VDC
Vol
tage
step
dow
n
Photocoupler
Photocoupler
Inte
rnal
circ
uits
V1 24 VDC
0
1
G1
Phy
sica
lla
yer
Communicationsconnector
DC-DCConverter
(non-insulated)
V+
CAN H
DRAIN
CAN L
V−
Photo-coupler
Photocoupler0
1
G2
Photocoupler
V2 24 VDC
Vol
tage
step
dow
n
Photocoupler
Photocoupler
Inte
rnal
circ
uits
V1 24 VDC
0
1
G1
Phy
sica
lla
yer
DC-DCConverter
(non-insulated)
V+
CAN H
DRAIN
CAN L
V−
Communicationsconnector
DRT2-Series Smart Slave 13
MIL Connector Terminals with Transistors DRT2-ID16ML(X) DRT2-ID16ML(X)-1
DRT2-OD16ML(X) DRT2-OD16ML(X)-1
V
Input (0 to 15)
GPhotocoupler
Inte
rnal
circ
uits
Physicallayer
V+
CAN H
DRAIN
CAN L
V−
DC-DCConverter
(non-insulated)
Inte
rnal
circ
uits G
Input (0 to 15)
VPhotocoupler
Physicallayer
V+
CAN H
DRAIN
CAN L
V−
DC-DCConverter
(non-insulated)
Inte
rnal
circ
uits
Photocoupler
Vol
tage
step
dow
n
V
Output (0 to 15)
G
Physicallayer
V+
CAN H
DRAIN
CAN L
V−
DC-DCConverter
(non-insulated)
Photocoupler
Vol
tage
step
dow
n
V
Output (0 to 15)
G
Inte
rnal
circ
uits
Physicallayer
V+
CAN H
DRAIN
CAN L
V−
DC-DCConverter
(non-insulated)
14 DRT2-Series Smart Slave
Standard Environment-resistive Terminals and Environment-resistive Terminals with TransistorsDRT2-ID04CL (NPN) DRT2-ID04CL-1 (PNP)
DRT2-OD04CL (NPN) DRT2-OD04CL-1 (PNP)
DRT2-ID08CL (NPN) DRT2-ID08CL-1 (PNP)
DRT2-OD08CL (NPN) DRT2-OD08CL-1 (PNP)
4
23 1
4
23 14
52
1 3
CAN-L
CAN-H
V+
V−
DRAIN
G
V
IN0
IN1
VG
VG
314
2In
tern
al c
ircui
ts
4
2
3 1
G
V
IN0
IN1
VG
VG
4
2
3 145
2
1 3
CAN-L
CAN-H
DRAIN
314
2
V+
V−
Inte
rnal
circ
uits
4
23 1
4
23 1
G V
OUT0
OUT1
V
V452
1 3
CAN-L
CAN-H
DRAIN
Vol
tage
step
dow
n
314
2
V+
V−
Inte
rnal
circ
uits
4
23 1
4
23 1
G V
OUT0
OUT1
G
G452
1 3
CAN-L
CAN-H
DRAIN
314
2Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
4
2
3 1
4
2
3 145
2
1 3
CAN-L
CAN-H
DRAIN
G
V
IN0
IN1
VG
VG
314
2
V+
V−
Inte
rnal
circ
uits
4
23 1
G
V
IN0
IN1
VG
VG
4
23 14
52
1 3
CAN-L
CAN-H
DRAIN
314
2
V+
V−
Inte
rnal
circ
uits
4
23 1
4
23 1
G V
OUT0
OUT1
V
V452
1 3
CAN-L
CAN-H
DRAIN
314
2
Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
4
23 1
4
23 1
G V
OUT0
OUT1
G
G452
1 3
CAN-L
CAN-H
DRAIN
314
2Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
DRT2-Series Smart Slave 15
DRT2-HD16CL (NPN) DRT2-HD16CL-1 (PNP)
DRT2-WD16CL (NPN) DRT2-WD16CL-1 (PNP)
DRT2-MD16CL (NPN) DRT2-MD16CL-1 (PNP)
4
23 14
52
1 3
CAN-L
CAN-H
DRAIN
G
V
IN0
IN1
VG
314
2
V+
V−
Inte
rnal
circ
uits
G
V
IN0
IN1
VG4
2
3 145
2
1 3
CAN-L
CAN-H
DRAIN
314
2
V+
V−
Inte
rnal
circ
uits
4
23 1
G V
OUT0
OUT1
V452
1 3
CAN-L
CAN-H
DRAIN
314
2
Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
4
23 1
G V
OUT0
OUT1
G452
1 3
CAN-L
CAN-H
DRAIN
314
2Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
4
23 1
OUT0
OUT1
V
452
1 3
CAN-L
CAN-H
DRAIN
4
23 1
G1
V1
IN0
IN1
VG
314
2
V2G2
Vol
tage
step
dow
n
V+
V−
Inte
rnal
circ
uits
4
23 1
OUT0
OUT1
G
452
1 3
CAN-L
CAN-H
DRAIN
G1
V1
IN0
IN1
VG4
23 1
314
2
V2G2
Vol
tage
step
dow
nV+
V−
Inte
rnal
circ
uits
16 DRT2-Series Smart Slave
Dimensions (Unit: mm)
Remote I/O Terminals with Transistors
MIL Connector Terminals with Transistors
Standard Environment-resistive Terminals and Environment-resistive Terminals with Transistors
49.7
29.9
43.9
50
3.1115
Remote I/O TerminalsDRT2-ID08(-1)DRT2-OD08(-1)DRT2-MD16(-1)
Dimensions inside parentheses are for reference only.35
52.7
80
60
63
5
(83)DRT2-ID16ML(-1)DRT2-OD16ML(-1)DRT2-ID16MLX(-1)DRT2-OD16MLX(-1)
34
AAB
B
1A
2AB
B
27.337.7
(125)
60
123
113±0.2
Two, M5 holes or 5.3 dia.
DRT2-ID04CL(-1)DRT2-OD04CL(-1)
Mounting hole dimensions
DRT2-Series Smart Slave 17
Wiring Diagrams
Remote I/O Terminals with TransistorsDRT2-MD16 (NPN) DRT2-MD16-1 (PNP)
DRT2-ID08 (NPN) DRT2-ID08-1 (PNP)
DRT2-OD08 (NPN) DRT2-OD08-1 (PNP)
4 87
B A B A B A
B A B A B A B A
AB
3
21 5
6OUT
43.9
26.624.3
175
60
Two 5.3 dia. or M5 holes
27.3
54
321098
7 6 54
321098
7 6
NO
DA
DR
X 10
X 1
AU
XP
WR
165±0.2
DRT2-ID08CL(-1)DRT2-OD08CL(-1)DRT2-HD16CL(-1)DRT2-WD16CL(-1)DRT2-MD16CL(-1)
Mounting hole dimensions
V1 1 3 5 7 V2
G1 0 2 4 6 G2
24 VDC
I/O power supply
Two-wire sensor(Limit switch, etc.)
+−
1 3 75 NC
0 2 4 6 NC
Bro
wn
(r
ed)
I/O power supply
Solenoid,etc.
+−
Valve, etc.
Bla
ck
(whi
te)
Blu
e
(bla
ck)
Bro
wn
(w
hite
)
Blu
e
(bla
ck)
Three-wire sensor with NPN output
(e.g., photoelectric sensor or proximity sensor)
V1 1 3 5 7 V2
G1 0 2 4 6 G2
24 VDC
1 3 75
0 2 4 6
NC
NC
I/O power supply
Solenoid,etc. Valve,etc.
I/O power supply
Two-wire sensor(Limit switch, etc.)
Bro
wn
(r
ed)
Bla
ck
(whi
te)
Blu
e
(bla
ck)
Bro
wn
(w
hite
)
Blu
e
(bla
ck)
Three-wire sensor with PNP output
(e.g., photoelectric sensor or proximity sensor)
+− +−
V 1 3 5 7
G 0 2 4 6
24 VDC
NCNC NC NC
NCNC NC NC
I/O power supply
+−
Two-wire sensor(Limit switch, etc.)
Bro
wn
(r
ed)
Bla
ck
(whi
te)
Blu
e
(bla
ck)
Bro
wn
(w
hite
)
Blu
e
(bla
ck)
Three-wire sensor with NPN output
(e.g., photoelectric sensor or proximity sensor)
V 1 3 5 7
G 0 2 4 6
24 VDC
NCNC NC NC
NCNC NC NC
I/O power supply
Two-wire sensor(Limit switch, etc.)
Bro
wn
(r
ed)
Bla
ck
(whi
te)
Blu
e
(bla
ck)
Bro
wn
(w
hite
)
Blu
e
(bla
ck)
Three-wire sensor with PNP output
(e.g., photoelectric sensor or proximity sensor)
+−
V 1 3 5 7
G 0 2 4 6
24VDC
NCNC NC NC
NCNC NC NC
Solenoid,etc. Valve,etc.
I/O power supply
+−
V 1 3 5 7
G 0 2 4 6
24 VDC
NCNC NC NC
NCNC NC NC
Solenoid,etc. Valve,etc.
I/O power supply
+−
18 DRT2-Series Smart Slave
MIL Connector Terminals with Transistors DRT2-ID16ML(X) DRT2-ID16ML(X)-1
DRT2-OD16ML(X) DRT2-OD16ML(X)-1
24 VDC
1920
V V
G G
1718
1516
1314
11
10
12
9
8 7
6 5
4 3
2 1
mch03
mch11
mch02
mch10
mch01
mch09
mch00
mch08
mch04
mch12
mch05
mch13
mch06
mch14
mch07
mch15
24 VDC
1920
V V
G G
1718
1516
1314
11
10
12
9
8 7
6 5
4 3
2 1
mch03
mch11
mch02
mch10
mch01
mch09
mch00
mch08
mch04
mch12
mch05
mch13
mch06
mch14
mch07
mch15
L
L
L
L
L
L
L
LL
L
L
L
L
L
L
L
24 VDC
1920
V V
G G
1718
1516
1314
11
10
12
9
8 7
6 5
4 3
2 1
mch03
mch11
mch02
mch10
mch01
mch09
mch00
mch08
mch04
mch12
mch05
mch13
mch06
mch14
mch07
mch15 L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
24 VDC
1920
V V
G G
1718
1516
1314
11
10
12
9
8 7
6 5
4 3
2 1
mch03
mch11
mch02
mch10
mch01
mch09
mch00
mch08
mch04
mch12
mch05
mch13
mch06
mch14
mch07
mch15
DRT2-ID16MLX(-1)/DRT2-OD16MLX(-1)Wiring Diagram for Enclosed Cable (with Connectors)
20
18
14
12
4
2
19
17
13
11
3
1
20
18
14
12
4
2
19
17
13
11
3
1
XG4M-2030-T(mating portion side)
XG4M-2030-T(mating portion side)
Triangle mark
Triangle mark
100 mm
DRT2-Series Smart Slave 19
Standard Environment-resistive Terminals and Environment-resistive Terminals with Transistors DRT2-ID04CL (NPN) DRT2-ID04CL-1 (PNP)
DRT2-OD04CL (NPN) DRT2-OD04CL-1 (PNP)
0V
24V
12
43
VNC
G Input 2
2 3
1 4
NC
V V
G
Input 1
2 3
1 4
NC G
Input 3
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
1
2
4
3NC
NC
I/O power supply 24 VDC
12
43
VNC
G Input 0
Three-wire sensor with NPN output (e.g., photoelectric sensor or proximity sensor)
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
12
43
VNC
G Input 0
12
43
VNC
G Input 2
2 3
1 4
NC NC
V
G
Input 1
2 3
1 4V
G
Input 3
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
1
2
4
3NC
0V
24V
NC
I/O power supply 24 VDC
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
Three-wire sensor with PNP output (e.g.,photoelectric sensor or proximity sensor)
12
433
V
Output 0
12
43
V
Output 2
2 3
1 4V Output 1
2 3
1 4V Output 3
1 2
4
V+
CAN H
CAN L
5 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
2NC
10V3
24V
4NC
I/O power supply
NC
NC
NC NC
NC
NC
NC NC
12
43Output 0
12
43Output 2
2 3
1 4Output 1
2 3
1 4Output 3
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
2NC
10V3
24V
4NC
I/O power supply
NCNC
NC
NC
NC NC
NC
NC
G G
GG
20 DRT2-Series Smart Slave
DRT2-ID08CL (NPN)
DRT2-ID08CL-1 (PNP)
DRT2-OD08CL (NPN)
12
43
VNC
G Input 0
12
43
V VNC
G Input 4
12
43
VNC
G Input 2
12
43
NC
G Input 6
2 3
1 4
NC
V
G
Input 1
2 3
1 4
NC
V
G
Input 5
2 3
1 4
NC
V
G
Input 3
2 3
1 4
NC
V
G
Input 7
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
1
2
4
3NC
NC
24V
0V
I/O power supply 24 VDC
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
Three-wire sensor with NPN output (e.g., photoelectric sensor or proximity sensor)
12
43
VNC
G Input 0
12
43
VNC
G Input 4
12
43
VNC
G Input 2
12
43
VNC
G Input 6
2 3
1 4
NC
V
G
Input 1
2 3
1 4
NC
V
G
Input 5
2 3
1 4
NC
V
G
Input 3
2 3
1 4
NC
V
G
Input 7
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
1
2
4
3NC
NC
24V
0V
I/O power supply 24 VDC
Three-wire sensor with PNP output (e.g., photoelectric sensor or proximity sensor)
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
12
43
V
Output 4
12
43
V
Output 2
12
43
V
Output 6
2 3
1 4
NC
V VOutput 1
2 3
1 4Output 5
2 3
1 4V Output 3
2 3
1 4V Output 7
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
12
43
V
Output 02NC
10V3
24V
4NC
I/O power supply
NC
NC
NC
NC
NC
NC NC
NC
NC
NC NC
NC
NC
NC NC
DRT2-Series Smart Slave 21
DRT2-OD08CL-1 (PNP)
DRT2-HD16CL (NPN)
DRT2-HD16CL-1 (PNP)
12
43Output 4
12
43output 2
12
43Output 6
2 3
1 4
NC
Output 1
2 3
1 4Output 5
2 3
1 4Output 3
2 3
1 4Output 7
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
12
43Output 02
NC
10V3
24V
4NC
I/O power supply
NCNC
NC
NCNC
NC
NC
NCNC
NC
NC
NC NC
NC
NC
G
G
G G G
G G G
12
43
V
G Input 0
12
43
V
G
Input 8
12
43
V
G Input 4
12
43
V
G Input 12
2 3
1 4
NC
V
G
Input 2
2 3
1 4V
G
Input 10
2 3
1 4V
G
Input 6
2 3
1 4V
G
Input 14
1 2
4
V+
CAN H
CAN L
35 V−
DRAINInput 1
Input 3
Input 5 Input 9 Input 13
Input 15Input 11
Input 7
1
2
4
3NC
NC
24V
0V
I/O power supply 24 VDC
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
Three-wire sensor with NPN output
(e.g., photoelectric sensor or proximity sensor)
Three-wire sensor with NPN output (e.g., photoelectric sensor or
proximity sensor)
12
43
V
G Input 0
12
43
V
G
Input 8
12
43
V
G Input 4
12
43
V
G Input 12
2 3
1 4
NC
V
G
Input 2
2 3
1 4V
G
Input 10
2 3
1 4V
G
Input 6
2 3
1 4V
G
Input 14
1 2
4
V+
CAN H
CAN L
35 V−
DRAINInput 1
Input 3
Input 5 Input 9 Input 13
Input 15Input 11
Input 7
1
2
4
3NC
NC
24V
0V
I/O power supply 24 VDC
Three-wire sensor withPNP output (e.g.,
photoelectric sensor orproximity sensor)
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Three-wire sensor withPNP output (e.g.,
photoelectric sensor orproximity sensor)
Bro
wn
(red
)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
22 DRT2-Series Smart Slave
DRT2-WD16CL (NPN)
DRT2-WD16CL-1 (PNP)
DRT2-MD16CL (NPN)
12
43
V
Output 8
12
43
V
Output 4
12
43
V
Output 12
2 3
1 4V Output 2
2 3
1 4Output 10
2 3
1 4V Output 6
2 3
1 4V Output 14
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
12
43
V
Output 02NC
10V3
24V
4NC
I/O power supply
NC
NC
NC
NC
NC
NC
NC
NC
Output 1
Output 3
Output 5
Output 7
Output 9
Output 11
Output 13
Output 15
V
12
43Output 8
12
43Output 4
12
43Output 12
2 3
1 4Output 2
2 3
1 4Output 10
2 3
1 4Output 6
2 3
1 4
Output 14
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc. Solenoid valve, etc.
12
43Output 02
NC
10V3
24V
4NC
I/O power supply
NC
NC
NC
NC
NC
NC
NC
NC
G
G
G G G
G G G
Output 1
Output 3
Output 5
Output 7
Output 9
Output 11
Output 13
Output 15
12
43
V2
Output 4
12
43Input 4
12
43
V2
OUT4
2 3
1 4V1 Input 2
2 3
1 4Output 2
2 3
1 4V1 Input 6
2 3
1 4V2V2 Output 6
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN
Solenoid valve, etc.
12
43
V1
Input 02
V2 1G23
4V1
G1
G1
NC
G1
NC
NC
NC
NC
Input 1
Input 3
Input 5
Input 7
Output 1
Output 3
Output 5
Output 7
24 V for outputs
24 V for inputs
V1
Solenoid valve, etc.
G1
I/O power supply
Three-wire sensor withNPN output (e.g.,
photoelectric sensor orproximity sensor)
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
DRT2-Series Smart Slave 23
DRT2-MD16CL-1 (PNP)
12
43
NC
Output 0
12
43Input 4
12
43
NC
OUT4
2 3
1 4V1 Input 2
2 3
1 4Output 2
2 3
1 4V1 Input 6
2 3
1 4NCNC Output 6
1 2
4
V+
CAN H
CAN L
35 V−
DRAIN 12
43
V1
Input 02
V2 1G23
4V1
G1
G1
NC
G1
G2
G2
G2
G2
Input 1
Input 3
Input 5
Input 7
Output 1
Output 3
Output 5
Output 7
24 V for outputs
24 V for inputs
V1
G1
Solenoid valve, etc.
I/O power supply
Three-wire sensor withPNP output (e.g.,
photoelectric sensor orproximity sensor)
Two-wire sensor(Limit switch, etc.)
Blu
e (b
lack
)
Bro
wn
(whi
te)
Blu
e (b
lack
)
Bla
ck (
whi
te)
Bro
wn
(red
)
Solenoid valve, etc.
24 DRT2-Series Smart Slave
Applicable Cables
MIL Connectors with Transistors Connector-Terminal Block Conversion Unit and Connecting
Cable (16 Points) Cables with Connectors (1:1)
I/O Relay Terminal Connector Cables (16 Points) Cables with Connectors (1:1)
Cables with Loose Wires with Crimp Terminals
Cables with Loose Wires
ModelApplicable
cableConnected Relay
TerminalRemarks
DRT2-ID16MLDRT2-ID16ML-1DRT2-OD16MLDRT2-OD16ML-1
G79-O@C
XW2D-20G6XW2B-20G5XW2B-20G4XW2C-20G6-IO16
Connector Terminal Block Conversion Unit
ModelApplicable
cableConnected Relay
TerminalRemarks
DRT2-ID16ML G79-I@CG7TC-ID16G7TC-IA16
For I/O Relay Terminal inputs
DRT2-ID16ML-1 --- ---(No applicable models)
DRT2-OD16ML G79-O@C
G7TC-OC16/OC08G70D-SOC16/VSOC16G70D-FOM16/VFOM16G70A-ZOC16-3G70D-SOC08G70R-SOC08
For I/O Relay Terminal outputs
DRT2-OD16ML-1
G79-I@C G7TC-OC16-1For I/O Relay Terminal outputs
G79-O@CG70D-SOC16-1G70D-FOM16-1G70A-Z0C16-4
For I/O Relay Terminal outputs
Model Applicable cable Remarks
DRT2-ID16MLDRT2-ID16ML-1DRT2-OD16MLDRT2-OD16ML-1
G79A-Y@C-D1
20-pole connector/bundled cable (with crimp-style terminals) conversion cable
Model Applicable cable Remarks
DRT2-ID16MLDRT2-ID16ML-1DRT2-OD16MLDRT2-OD16ML-1
G79A-A@C-D120-pole connector/bundled cable conversion cable
DRT2-Series Smart Slave 25
List of Models
DRT2-series Smart Slaves
Product name Shape Model SpecificationsApprovedstandards
Remote I/O Basic Terminals with Transistors
DRT2-ID16 16 inputs, NPN ( + common)
UC, CE
DRT2-ID16-1 16 inputs, PNP ( − common)
DRT2-OD16 16 outputs, NPN ( − common)
DRT2-OD16-1 16 outputs, PNP ( + common)
DRT2-MD168 inputs/8 outputs with NPN, + common for inputs, − common for outputs
DRT2-MD16-18 inputs/8 outputs with PNP, − common for inputs, + common for outputs
DRT2-ID08 8 inputs, NPN ( + common)
DRT2-ID08-1 8 inputs, PNP ( − common)
DRT2-OD08 8 outputs, NPN ( − common)
DRT2-OD08-1 8 outputs, PNP ( + common)
Remote I/O Terminal Expansion Units with Transistors
XWT-ID08 8 inputs for terminals with NPN, + common
UC, CE
XWT-ID08-1 8 inputs for terminals with PNP, − common
XWT-OD08 8 outputs for terminals with NPN, − common
XWT-OD08-1 8 outputs for terminals with PNP, + common
XWT-ID16 16 inputs for terminals with NPN, + common
XWT-ID16-1 16 inputs for terminals with PNP, − common
XWT-OD16 16 outputs for terminals with NPN, − common
XWT-OD16-1 16 outputs for terminals with PNP, + common
Remote I/o Terminals with 3-tier Terminal Blocks with Transistors
DRT2-ID16TA 16 inputs with NPN, + common
UC, CE
DRT2-ID16TA-1 16 inputs with PNP, − common
DRT2-OD16TA 16 outputs with NPN, − common
DRT2-OD16TA-1 16 outputs with PNP, + common
DRT2-MD16TA8 inputs/8 outputs with NPN, + common for inputs, − common for outputs
DRT2-MD16TA-18 inputs/8 outputs with PNP, − common for inputs, + common for outputs
MIL Connector Terminals with Transistors
DRT2-ID32ML 32 inputs with NPN, + common
UC, CE
DRT2-ID32ML-1 32 inputs with PNP, − common
DRT2-OD32ML 32 outputs with NPN, − common
DRT2-OD32ML-1 32 outputs with PNP, + common
DRT2-MD32ML16 inputs/16 outputs with NPN, + common for inputs, − common for outputs
DRT2-MD32ML-116 inputs/16 outputs with PNP, − common for inputs, + common for outputs
DRT2-ID16ML 16 inputs with NPN, + common
DRT2-ID16ML-1 16 inputs with PNP, − common
DRT2-OD16ML 16 outputs with NPN, − common
DRT2-OD16ML-1 16 outputs with PNP, + common
DRT2-ID16MLX 16 inputs with NPN, + common, cable with connectors: 10 cm
DRT2-ID16MLX-1 16 inputs with PNP, − common, cable with connectors: 10 cm
DRT2-OD16MLX 16 outputs with NPN, − common, cable with connectors: 10 cm
DRT2-OD16MLX-1 16 outputs with PNP, + common, cable with connectors: 10 cm
Remote I/O Terminals with Relay Outputs
DRT2-ROS16 16 outputs UR, CE
Board Terminals with MIL Connectors (horizontal mounting)
DRT2-ID32B 32 inputs, NPN ( + common)
U, CE
DRT2-ID32B-1 32 inputs, PNP ( − common)
DRT2-OD32B 32 outputs, NPN ( − common)
DRT2-OD32B-1 32 outputs, PNP ( + common)
DRT2-MD32B 16 inputs/16 outputs, NPN (inputs: + common/outputs: − common)
DRT2-MD32B-1 16 inputs/16 outputs, PNP (inputs: − common/outputs: + common)
Board Terminals with MIL Connectors (vertical mounting)
DRT2-ID32BV 32 inputs, NPN ( + common)
U, CE
DRT2-ID32BV-1 32 inputs, PNP ( − common)
DRT2-OD32BV 32 outputs, NPN ( − common)
DRT2-OD32BV-1 32 outputs, PNP ( + common)
DRT2-MD32BV 16 inputs/16 outputs, NPN (inputs: + common/outputs: − common)
DRT2-MD32BV-1 16 inputs/16 outputs, PNP (inputs: − common/outputs: + common)
26 DRT2-Series Smart Slave
Product name Shape Model SpecificationsApproved standards
Screw-less Clamp Terminals with Transistors
DRT2-ID32SLH 32 inputs, NPN ( + common) with detection functions
UC, CE
DRT2-ID32SLH-1 32 inputs, PNP ( − common) with detection functions
DRT2-OD32SLH 32 outputs, NPN ( − common) with detection functions
DRT2-OD32SLH-1 32 outputs, PNP ( + common) with detection functions
DRT2-MD32SLH16 inputs/16 outputs, NPN (inputs: + common/outputs: − common) with detection functions
DRT2-MD32SLH-116 inputs/16 outputs, PNP (inputs: − common/outputs: + common) with detection functions
DRT2-ID32SL 32 inputs, NPN ( + common) without detection functions
DRT2-ID32SL-1 32 inputs, PNP ( − common) without detection functions
DRT2-OD32SL 32 outputs, NPN ( − common) without detection function
DRT2-OD32SL-1 32 outputs, PNP ( + common) without detection function
DRT2-MD32SL16 inputs/16 outputs, NPN (inputs: + common/outputs:− common) without detection function
DRT2-MD32SL-116 inputs/16 outputs, PNP (inputs: − common/outputs: + common) without detection function
Environment-resistive Terminals with Transistors
DRT2-ID08C 8 inputs, NPN ( + common) with detection functions
UC, CE
DRT2-ID08C-1 8 inputs, PNP ( − common) with detection functions
DRT2-OD08C 8 outputs, NPN ( − common) with detection functions
DRT2-OD08C-1 8 outputs, PNP ( + common) with detection functions
DRT2-HD16C 16 inputs, NPN ( + common) with detection functions
DRT2-HD16C-1 16 inputs, PNP ( − common) with detection functions
Environment-resistive Terminals with Transistors
DRT2-ID04CL 4 inputs, NPN ( + common) without detection functions
UC, CEDRT2-ID04CL-1 4 inputs, PNP ( − common) without detection functions
DRT2-OD04CL 4 outputs, NPN ( − common) without detection functions
DRT2-OD04CL-1 4 outputs, PNP ( + common) without detection functions
DRT2-ID08CL 8 inputs, NPN ( + common) without detection functions
UC, CE
DRT2-ID08CL-1 8 inputs, PNP ( − common) without detection functions
ÅDRT2-OD08CL 8 outputs, NPN ( − common) without detection functions
DRT2-OD08CL-1 8 outputs, PNP ( + common) without detection functions
DRT2-HD16CL 16 inputs, NPN ( + common) without detection functions
DRT2-HD16CL-1 16 inputs, PNP ( − common) without detection functions
DRT2-WD16CL 16 outputs, NPN ( − common) without detection functions
DRT2-WD16CL-1 16 outputs, PNP ( + common) without detection functions
DRT2-MD16CL8 inputs/8 outputs, NPN (inputs: + common/outputs: − common) without detection function
DRT2-MD16CL-18 inputs/8 outputs, PNP (inputs: − common/outputs: + common) without detection function
e-con Connector Terminals
DRT2-ID16S 16 inputs, NPN ( + common)
UC, CEDRT2-ID16S-1 16 inputs, PNP ( − common)
DRT2-MD16S 8 inputs/8 outputs, NPN (inputs: + common/outputs:− common)
DRT2-MD16S-1 8 inputs/8 outputs, PNP (inputs: − common/outputs: + common)
Analog Input TerminalsDRT2-AD04 4 inputs (resolution: 6,000)
UC, CEDRT2-AD04H 4 inputs (resolution: 30,000)
Analog Output Terminals DRT2-DA02 2 outputs
Temperature Input Terminals with Thermocouple Inputs
DRT2-TS04T 4 inputs
U, CETemperature Input Terminals with Resistance-thermometer Inputs
DRT2-TS04P 4 inputs
DRT2-Series Smart Slave 27
Intelligent Slaves
Product name Shape Model SpecificationsApproved standards
Modular Temperature Controllers
E5ZN-DRT DeviceNet Communications Unit for E5ZN
---E5ZN-SCT24S Terminal Unit
--- E5ZN-SDL Setting Display Unit
Multi-function Compact Inverter
3G3MV-PDRT2 Communications Unit for 3G3MV Inverters U, CE
High-function General-purpose Inverters
3G3RV-PDRT2 3G3RV/3G3FV DeviceNet Communications Card U, CE
Terms and Conditions of Sale1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,catalogs, manuals, brochures and other documents, whether electronic or inwriting, relating to the sale of products or services (collectively, the "Products")by Omron Electronics LLC and its subsidiary companies (“Omron”). Omronobjects to any terms or conditions proposed in Buyer’s purchase order or otherdocuments which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-out notice by Omron. Omron reserves the right to increase or decrease priceson any unshipped portions of outstanding orders. Payments for Products aredue net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoicessent to Buyer after deducting transportation charges, taxes and duties, and willbe allowed only if (i) the invoice is paid according to Omron’s payment termsand (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month orthe maximum legal rate, whichever is less, on any balance not paid within thestated terms.
5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than generalreal property and income taxes), including any interest or penalties thereon,imposed directly or indirectly on Omron or required to be collected directly orindirectly by Omron for the manufacture, production, sale, delivery, importa-tion, consumption or use of the Products sold hereunder (including customsduties and sales, excise, use, turnover and license taxes) shall be charged toand remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactoryto Omron, Omron reserves the right to stop shipments or require satisfactorysecurity or payment in advance. If Buyer fails to make payment or otherwisecomply with these Terms or any related agreement, Omron may (without liabil-ity and in addition to other remedies) cancel any unshipped portion of Prod-ucts sold hereunder and stop any Products in transit until Buyer pays allamounts, including amounts payable hereunder, whether or not then due,which are owing to it by Buyer. Buyer shall in any event remain liable for allunpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellationunless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in deliveryresulting from causes beyond its control, including earthquakes, fires, floods,strikes or other labor disputes, shortage of labor or materials, accidents tomachinery, acts of sabotage, riots, delay in or lack of transportation or therequirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shallpass from Omron to Buyer; provided that Omron shall retain a security inter-est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; ande. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writingto Omron within 30 days of receipt of shipment and include the original trans-portation bill signed by the carrier noting that the carrier received the Productsfrom Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that theProducts will be free from defects in materials and workmanship for a period oftwelve months from the date of sale by Omron (or such other period expressedin writing by Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THEPRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIRINTENDED USE. Omron further disclaims all warranties and responsibility ofany type for claims or expenses based on infringement by the Products or oth-erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-gation hereunder shall be, at Omron’s election, to (i) replace (in the formoriginally shipped with Buyer responsible for labor charges for removal orreplacement thereof) the non-complying Product, (ii) repair the non-complyingProduct, or (iii) repay or credit Buyer an amount equal to the purchase price ofthe non-complying Product; provided that in no event shall Omron be responsi-ble for warranty, repair, indemnity or any other claims or expenses regardingthe Products unless Omron’s analysis confirms that the Products were prop-erly handled, stored, installed and maintained and not subject to contamina-tion, abuse, misuse or inappropriate modification. Return of any Products byBuyer must be approved in writing by Omron before shipment. Omron Compa-nies shall not be liable for the suitability or unsuitability or the results from theuse of Products in combination with any electrical or electronic components,circuits, system assemblies or any other materials or substances or environ-ments. Any advice, recommendations or information given orally or in writing,are not to be construed as an amendment or addition to the above warranty.See http://oeweb.omron.com or contact your Omron representative for pub-lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLEFOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANYWAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM ISBASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individualprice of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies andtheir employees from and against all liabilities, losses, claims, costs andexpenses (including attorney's fees and expenses) related to any claim, inves-tigation, litigation or proceeding (whether or not Omron is a party) which arisesor is alleged to arise from Buyer's acts or omissions under these Terms or inany way with respect to the Products. Without limiting the foregoing, Buyer (atits own expense) shall indemnify and hold harmless Omron and defend or set-tle any action brought against such Companies to the extent based on a claimthat any Product made to Buyer specifications infringed intellectual propertyrights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-sive property of Omron Companies and Buyer shall not attempt to duplicate itin any way without the written permission of Omron. Notwithstanding anycharges to Buyer for engineering or tooling, all engineering and tooling shallremain the exclusive property of Omron. All information and materials suppliedby Omron to Buyer relating to the Products are confidential and proprietary,and Buyer shall limit distribution thereof to its trusted employees and strictlyprevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations andlicenses regarding (i) export of products or information; (iii) sale of products to“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens ofregulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any rightand no course of dealing between Buyer and Omron shall operate as a waiverof rights by Omron. (b) Assignment. Buyer may not assign its rights hereunderwithout Omron's written consent. (c) Law. These Terms are governed by thelaw of the jurisdiction of the home office of the Omron company from whichBuyer is purchasing the Products (without regard to conflict of law princi-ples). (d) Amendment. These Terms constitute the entire agreement betweenBuyer and Omron relating to the Products, and no provision may be changedor waived unless in writing signed by the parties. (e) Severability. If any provi-sion hereof is rendered ineffective or invalid, such provision shall not invalidateany other provision. (f) Setoff. Buyer shall have no right to set off any amountsagainst the amount owing in respect of this invoice. (g) Definitions. As usedherein, “including” means “including without limitation”; and “Omron Compa-nies” (or similar words) mean Omron Corporation and any direct or indirectsubsidiary or affiliate thereof.
Certain Precautions on Specifications and Use1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of theProduct in the Buyer’s application or use of the Product. At Buyer’s request,Omron will provide applicable third party certification documents identifyingratings and limitations of use which apply to the Product. This information byitself is not sufficient for a complete determination of the suitability of the Prod-uct in combination with the end product, machine, system, or other applicationor use. Buyer shall be solely responsible for determining appropriateness ofthe particular Product with respect to Buyer’s application, product or system.Buyer shall take application responsibility in all cases but the following is anon-exhaustive list of applications for which particular attention must be given:(i) Outdoor use, uses involving potential chemical contamination or electricalinterference, or conditions or uses not described in this document.(ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviationsystems, medical equipment, amusement machines, vehicles, safety equip-ment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or prop-erty. Please know and observe all prohibitions of use applicable to this Prod-uct. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUSRISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUTENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THEOVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for theuser’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogsand other materials is provided as a guide for the user in determining suitabil-ity and does not constitute a warranty. It may represent the result of Omron’stest conditions, and the user must correlate it to actual application require-ments. Actual performance is subject to the Omron’s Warranty and Limitationsof Liability.
4. Change in Specifications. Product specifications and accessories may bechanged at any time based on improvements and other reasons. It is our prac-tice to change part numbers when published ratings or features are changed,or when significant construction changes are made. However, some specifica-tions of the Product may be changed without any notice. When in doubt, spe-cial part numbers may be assigned to fix or establish key specifications foryour application. Please consult with your Omron’s representative at any timeto confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has beenchecked and is believed to be accurate; however, no responsibility is assumedfor clerical, typographical or proofreading errors or omissions.
MEMO
28
Terms and Conditions of Sale1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,catalogs, manuals, brochures and other documents, whether electronic or inwriting, relating to the sale of products or services (collectively, the "Products")by Omron Electronics LLC and its subsidiary companies (“Omron”). Omronobjects to any terms or conditions proposed in Buyer’s purchase order or otherdocuments which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-out notice by Omron. Omron reserves the right to increase or decrease priceson any unshipped portions of outstanding orders. Payments for Products aredue net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoicessent to Buyer after deducting transportation charges, taxes and duties, and willbe allowed only if (i) the invoice is paid according to Omron’s payment termsand (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month orthe maximum legal rate, whichever is less, on any balance not paid within thestated terms.
5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than generalreal property and income taxes), including any interest or penalties thereon,imposed directly or indirectly on Omron or required to be collected directly orindirectly by Omron for the manufacture, production, sale, delivery, importa-tion, consumption or use of the Products sold hereunder (including customsduties and sales, excise, use, turnover and license taxes) shall be charged toand remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactoryto Omron, Omron reserves the right to stop shipments or require satisfactorysecurity or payment in advance. If Buyer fails to make payment or otherwisecomply with these Terms or any related agreement, Omron may (without liabil-ity and in addition to other remedies) cancel any unshipped portion of Prod-ucts sold hereunder and stop any Products in transit until Buyer pays allamounts, including amounts payable hereunder, whether or not then due,which are owing to it by Buyer. Buyer shall in any event remain liable for allunpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellationunless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in deliveryresulting from causes beyond its control, including earthquakes, fires, floods,strikes or other labor disputes, shortage of labor or materials, accidents tomachinery, acts of sabotage, riots, delay in or lack of transportation or therequirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shallpass from Omron to Buyer; provided that Omron shall retain a security inter-est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; ande. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writingto Omron within 30 days of receipt of shipment and include the original trans-portation bill signed by the carrier noting that the carrier received the Productsfrom Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that theProducts will be free from defects in materials and workmanship for a period oftwelve months from the date of sale by Omron (or such other period expressedin writing by Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THEPRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIRINTENDED USE. Omron further disclaims all warranties and responsibility ofany type for claims or expenses based on infringement by the Products or oth-erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-gation hereunder shall be, at Omron’s election, to (i) replace (in the formoriginally shipped with Buyer responsible for labor charges for removal orreplacement thereof) the non-complying Product, (ii) repair the non-complyingProduct, or (iii) repay or credit Buyer an amount equal to the purchase price ofthe non-complying Product; provided that in no event shall Omron be responsi-ble for warranty, repair, indemnity or any other claims or expenses regardingthe Products unless Omron’s analysis confirms that the Products were prop-erly handled, stored, installed and maintained and not subject to contamina-tion, abuse, misuse or inappropriate modification. Return of any Products byBuyer must be approved in writing by Omron before shipment. Omron Compa-nies shall not be liable for the suitability or unsuitability or the results from theuse of Products in combination with any electrical or electronic components,circuits, system assemblies or any other materials or substances or environ-ments. Any advice, recommendations or information given orally or in writing,are not to be construed as an amendment or addition to the above warranty.See http://www.omron247.com or contact your Omron representative for pub-lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLEFOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANYWAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM ISBASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individualprice of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies andtheir employees from and against all liabilities, losses, claims, costs andexpenses (including attorney's fees and expenses) related to any claim, inves-tigation, litigation or proceeding (whether or not Omron is a party) which arisesor is alleged to arise from Buyer's acts or omissions under these Terms or inany way with respect to the Products. Without limiting the foregoing, Buyer (atits own expense) shall indemnify and hold harmless Omron and defend or set-tle any action brought against such Companies to the extent based on a claimthat any Product made to Buyer specifications infringed intellectual propertyrights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-sive property of Omron Companies and Buyer shall not attempt to duplicate itin any way without the written permission of Omron. Notwithstanding anycharges to Buyer for engineering or tooling, all engineering and tooling shallremain the exclusive property of Omron. All information and materials suppliedby Omron to Buyer relating to the Products are confidential and proprietary,and Buyer shall limit distribution thereof to its trusted employees and strictlyprevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations andlicenses regarding (i) export of products or information; (iii) sale of products to“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens ofregulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any rightand no course of dealing between Buyer and Omron shall operate as a waiverof rights by Omron. (b) Assignment. Buyer may not assign its rights hereunderwithout Omron's written consent. (c) Law. These Terms are governed by thelaw of the jurisdiction of the home office of the Omron company from whichBuyer is purchasing the Products (without regard to conflict of law princi-ples). (d) Amendment. These Terms constitute the entire agreement betweenBuyer and Omron relating to the Products, and no provision may be changedor waived unless in writing signed by the parties. (e) Severability. If any provi-sion hereof is rendered ineffective or invalid, such provision shall not invalidateany other provision. (f) Setoff. Buyer shall have no right to set off any amountsagainst the amount owing in respect of this invoice. (g) Definitions. As usedherein, “including” means “including without limitation”; and “Omron Compa-nies” (or similar words) mean Omron Corporation and any direct or indirectsubsidiary or affiliate thereof.
Certain Precautions on Specifications and Use1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of theProduct in the Buyer’s application or use of the Product. At Buyer’s request,Omron will provide applicable third party certification documents identifyingratings and limitations of use which apply to the Product. This information byitself is not sufficient for a complete determination of the suitability of the Prod-uct in combination with the end product, machine, system, or other applicationor use. Buyer shall be solely responsible for determining appropriateness ofthe particular Product with respect to Buyer’s application, product or system.Buyer shall take application responsibility in all cases but the following is anon-exhaustive list of applications for which particular attention must be given:(i) Outdoor use, uses involving potential chemical contamination or electricalinterference, or conditions or uses not described in this document.(ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviationsystems, medical equipment, amusement machines, vehicles, safety equip-ment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or prop-erty. Please know and observe all prohibitions of use applicable to this Prod-uct. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUSRISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUTENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THEOVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for theuser’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogsand other materials is provided as a guide for the user in determining suitabil-ity and does not constitute a warranty. It may represent the result of Omron’stest conditions, and the user must correlate it to actual application require-ments. Actual performance is subject to the Omron’s Warranty and Limitationsof Liability.
4. Change in Specifications. Product specifications and accessories may bechanged at any time based on improvements and other reasons. It is our prac-tice to change part numbers when published ratings or features are changed,or when significant construction changes are made. However, some specifica-tions of the Product may be changed without any notice. When in doubt, spe-cial part numbers may be assigned to fix or establish key specifications foryour application. Please consult with your Omron’s representative at any timeto confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has beenchecked and is believed to be accurate; however, no responsibility is assumedfor clerical, typographical or proofreading errors or omissions.
OMRON ELECTRONICS LLC • THE AMERICAS HEADQUARTERS
Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICESão Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ELECTRONICS MEXICO SA DE CV • HEAD OFFICEApodaca, N.L. • 52.811.156.99.10 • 001.800.556.6766 • [email protected]
OMRON ARGENTINA • SALES OFFICECono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICESantiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES54.11.4783.5300
© 2009 Omron Electronics LLC
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Note: This datasheet is provided as a guideline for selecting products. Do not use this document to operate the Unit.
Cat. No.R110-E1-05 1/07 Specifications are subject to change without notice. Printed in U.S.A.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron:
DRT2-OD16