SM - Stabilized Metal Film MELF Resistor · SM- Stabilized Metal Film MELF Resistor Specifications...

GUDECO Elektronik Handelsgesellschaft mbHFirmensitz: Niederlassungen:Siemensstraße 22D-61267 Neu-AnspachTelefon +49 (6081) 4 04-0Fax +49 (6081) 4 04-44

Alte Rhinstraße 16D-12681 BerlinTelefon +49 (30) 29 36 97-79Fax +49 (30) 29 36 97-88

Steinebach 13aA-6850 DornbirnTelefon +43 (5572) 38 65 56-670Fax +43 (5572) 38 65 56-688

Oetterichweg 7D-90411 NürnbergTelefon +49 (911) 53 99 23-0Fax +49 (911) 53 99 23-50

www.gudeco.de • [email protected]

[email protected]

Sep. 30, 2010

Quality • Reliability

Cost-Down via TechnologyQuality • Reliability

Cost-Down via Technology

SM - Stabilized Metal Film MELF Resistor

Specifications Per • IEC 60115-1 60115-2

• CECC 40101

• DIN 44061

Features• SMD enabled structure with excellent solderability

• Conformal coating against humidity

• 5% is 3-band coded, 2% and under is 4-band coded

• RoHS / REACH Compliant

DIMENSIONS

Type Body Length ( L, mm )

Body Diameter ( D, mm )

Soldering Spot ( B, mm )

Net WeightPer 1000 pcs

SM16 3.52 ± 0.08 1.35 ± 0.1 0.6 Min. 17 grams

SM204 3.52 ± 0.08 1.35 ± 0.1 0.6 Min. 17 grams

SM207 5.90 ± 0.2 2.2 ± 0.1 1.0 Min. 66 grams

SM52 5.90 ± 0.2 2.2 ± 0.1 1.0 Min. 66 grams

GENERAL SPECIFICATIONS

TypePowerRating

( at 70°C )

Max.WorkingVoltage

Max.OverloadVoltage

ResistanceRangeMin.

ResistanceRangeMax.

ResistanceTolerance

StandardResistance

Value

SM16 1/6W 200V 400V 0.51 Ω 10M Ω±1% E-24/E-96

±2%, 5% E-24

SM204 1/4W 200V 400V 0.51 Ω 10M Ω±1% E-24/E-96

±2%, 5% E-24

SM207 1/3W 250V 500V 0.51 Ω 10M Ω±1% E-24/E-96

±2%, 5% E-24

SM52 1/2W 250V 500V 0.51 Ω 10M Ω±1% E-24/E-96

±2%, 5% E-24

For zero-ohm jumper, please see ZMM series. For 0.5Ω & under, please see CSM series. Special sizes, values, and specifications not listed available on special order.

ORDERING INFORMATION (EXAMPLE)

Type Tolerance TemperatureCoefficient

ResistanceValue Packaging Special Request

(Optional)

SM16SM204 F (1%)

G (2%)J (5%)

TK50TK100

R87584K51M69

TR3 (3K/reel)TR6 (6K/reel)

TR10 (10K/reel) HV (High value)LV (Low value)

SM207SM52

TR2 (2K/reel)TR6 (6K/reel)

TR10 (10K/reel)

B

L D






128 [email protected]

Sep. 30, 2010





TECHNICAL SUMMARY

Characteristics Ranges & Limits

Operating Temperature Range, °C -55 ~ +125

Temperature Coefficient, PPM / °C±1%, 2% ±25, ±50

±5% ±100

Dielectric Withstanding Voltage, VAC or DCSM16, SM204 200

SM207, SM52 500

Insulation Resistance, MΩ >104

Film Temperature, °CSM16, SM204, SM207 125

SM52 140

Voltage Coefficient, PPM / V <0.5

Current noise, µV / V

<10KΩ <0.05

10KΩ ~ 100KΩ <0.2

100KΩ ~ 1MΩ <1

1MΩ ~ 10MΩ <3

Power derating 100% for temp. < 70 °C, linearly down to 0% at 125 °C

Failure Rate, pcs/109 device hours <1

Thermal Resistance, K/W <220

Tin Whisker (JESD201 Temperature Cycling & High Temp./Humidity Storage), µm

<5

SURGE PERFORMANCE

0.00001s 0.0001s 0.001s 0.01s 0.1s 1s

PEA

K P

OW

ER

(w

att)

PAPP

LIC

AB

LE

-PR

AT

ED

P

SUR

GE

100

10

1

10us 100us 1ms 10ms 100ms 1s

0.1

SM207, SM52SM16, SM204

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

0.0001 0.001 0.01 0.1 1 10

SURGE DURATIONSURGE DURATIONSURGE OFF TIME

SINGLE SURGE PERFORMANCE SURGE POWER DERATING CURVE

Notes:1. SINGLE SURGE PERFORMANCE graph is good for NON REPETITIVE applications operating in an ambient temperature of 70°C or less. For temperatures above 70°C, the graph power must be derated further linearly down to zero at 125°C.

2. To determine applicable surge power in continuous-surge applications: • Identify allowable duration and peak power Psurge of single surge; • Determine ratio of surge duration/surge OFF time in application; • Calculate Papplicable backwardly according to Y-axis of SURGE POWER DERATING CURVE.






[email protected]

Sep. 30, 2010





PERFORMANCE SPECIFICATIONS

Test Characteristics Test Conditions Limits

Short Time OverloadIEC 60115-1 4.132 seconds 2.5x rated voltage (not over max. overload voltage)

± (0.05%+0.05R)

Load LifeIEC 60115-1 4.25.1Rated load 1.5 hours ON, 0.5 hours OFF, at 70°C

1,000 hrs ± (0.25%+0.05R)

8,000 hrs ± (0.5%+0.05R)

225,000 hrs ± (1.5%+0.05R)

Load Life In HumidityIEC 60115-1 4.2456 days rated load at 40°C and 93% relative humidity

± (0.25%+0.05R)

Load Life In Humidity (accelerated mode)

IEC 60115-1 4.39 1,000 hours at 85°C and 85% relative humidity with 0.1x rated voltage (not over 100V)

± (0.5%+0.05R)

Periodic Electric OverloadIEC 60115-1 4.373.9x rated voltage (not over max. overload voltage) with 0.1s ON, 2.5s OFF for 1,000 cycles

± (2.5%+0.05R)

Resistance To Soldering HeatIEC 60115-1 4.1810 seconds at 260°C solder bath temperature

± (0.05%+0.05R)

Thermal Endurance IEC 60115-1 4.25.31,000 hours without load

85°C ± (0.2%+0.05R)

125°C ± (0.25%+0.05R)

Thermal Shock IEC 60115-1 4.19-55°C 30minutes, +125°C 30minutes

5 cycles ± (0.05%+0.05R)

1,000 cycles ± (0.5%+0.05R)

Single pulse high voltage overload

IEC 60115-1 4.27• 5 pulses of 1.2/50µs at 44.7x rated voltage (not over 2KV for SM16 & SM204; not over 4KV for SM207 & SM52) with interval of 12 sec. • 10 pulses of 10/700µs at 31.6x rated voltage (not over 2KV for SM16 & SM204; not over 4KV for SM207 & SM52) with interval of 60 sec.

± (0.5%+0.05R)

± (1.0%+0.05R)

Electrostatic discharge (Human body mode)

IEC 60115-1 4.403 positive & 3 negative discharges with 2KV for SM16 & SM204 or 4KV for SM207 & SM52 (For continuous surge application please see Surge Performance paragraph)

± (2.5%+0.05R)

Climatic test

IEC 60115-1 4.234.23.2 - dry heat: 16 hours 125°C4.23.3 - damp heat: 24 hours 55°C with 95% relative humidity4.23.4 - cold: 2 hours -55°C4.23.5 - negative air pressure: 2 hour 8.5KPa at 25°C4.23.6 - damp heat cyclic: 5 days 55°C with 95% relative humidity4.23.7 - DC load: rated voltage at -55°C and 125oC each 1 min.

± (0.5%+0.05R)

SolderabilityMIL-STD-202 Method 208Solder area covered after 230±5°C/5±0.5 seconds w/flux applied

> 95%

VibrationMIL-STD-202 Method 204Six hours in each parallel and axial direction with a simple harmonic motion having an amplitude of 1.52mm and 10 to 20,000 Hz.

± (1.0%+0.1R)

Bending testIEC 60115-1 4.33Pressing depth 2mm, 3 times

± (0.25%+0.05R)

FlammabilityIEC 60115-1 4.35Needle flame test 10s

No burning after 30s






130 [email protected]

Sep. 30, 2010





Recommended peeling force: 50gf

Type Soldering mode Pad Length(L, mm, min.)

Pad Spacing(P, mm)

Pad Width(W, mm, min.)

SM16SM204

Reflow 1.0 2.0 ± 0.2 1.6

Wave 1.2 2.0 ± 0.2 1.6

SM207SM52

Reflow 2.0 3.0 ± 0.3 3.0

Wave 2.5 3.0 ± 0.3 3.0

For better heat dissipation / lower heat resistance, increase W & L.

SUGGESTED PAD LAYOUT

COVER TAPE PEELING SPECIFICATION

SM- Stabilized Metal Film MELF Resistor Specifications Per Features IEC 60115-1 60115-2 SMD enabled structure CECC 40101 Conformal coating against humidity DIN 44061 Excellent solderability termination

5% is 3-band coded, 2% and under is 4-band coded

Dimensions

Type Body Length (L, mm)

Body Diameter (D, mm)

Soldering spot (B, mm)

Net Weight Per 1000 pcs

SM16 3.45 ± 0.1 1.35 ± 0.1 0.6 Min. 17 grams

SM204 3.45 ± 0.1 1.35 ± 0.1 0.6 Min. 17 grams

SM207 5.9 ± 0.2 2.2 ± 0.1 1.0 Min. 66 grams

SM52 5.9 ± 0.2 2.2 ± 0.1 1.0 Min. 66 grams

General Specifications

Type Power Rating

(at 70oC)

Max. Working Voltage

Max. Overload Voltage

Resistance Range Min.

Resistance Range Max.

Resistance Tolerance

Standard Resistance

Value ±1% E-24/E-96

SM16 1/6W 200V 400V 0.1　 1M　 ±2%, 5% E-24

±1% E-24/E-96 SM204 1/4W 200V 400V 0.1　 1M　

±2%, 5% E-24

±1% E-24/E-96 SM207 1/3W 250V 500V 0.1　 1M　

±2%, 5% E-24

±1% E-24/E-96 SM52 1/2W 250V 500V 0.1　 1M　

±2%, 5% E-24 For zero ohm jumper, please see ZMM series. For 1m~100mohm, please see CSM series. Special sizes, values, and specifications not listed available on special order.

Aug. 28, 2004

SM- Stabilized Metal Film MELF Resistor

1 .2 /5 0 u s P E A K P U L S E5 p u ls e s a t 1 2 -s e c in te rv a l fo r 0 .5 % p e rm a n e n t c h a n g e

1 0

1 0 0

1 0 0 0

1 0 0 0 0

R E S IS T A N C E V A L U E

PEA

K V

OLT

AG

E (v

olt)

1 Ω 1 0 Ω 1 0 0 Ω 1 K Ω 1 0 K Ω 1 0 0 K Ω 1 M Ω

S M 2 0 7 , S M 5 2

S M 1 6 , S M 2 0 4

POWER DERATING CURVE

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

30 40 50 60 70 80 90 100 110 120 130

AMBIENT TEMPERATURE (oC)

RATEDLOAD

SURGE POW ER DERATING CURVE

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

0.0001 0.001 0.01 0.1 1 10

Surge Duration Surge OFF time

Pap

plic

able

- P

rate

dP

surg

e

SINGLE SURGE PERFORMANCE

0.00001s 0.0001s 0.001s 0.01s 0.1s 1s

SURGE DURATION

PEA

K P

OW

ER (w

att)

100

10

1

10us 100us 1ms 10ms 100ms 1s

0.1

SM207, SM52

SM16, SM204

Notes: 1. Above graph is accurate for NON REPETITIVE applications operating in an ambient temperature of 70°C or less. For temperatures above 70°C, the graph power must be derated further linearly down to zero at 125°C. 2. For applicable surge power in continuous-surge applications please see SURGE POWER DERATING CURVE above.

Aug. 28, 2004

Aug. 28, 2004

SM- Stabilized Metal Film MELF Resistor Technical Summary:

Characteristics Limits

Dielectric Withstanding Voltage, VAC or DC SM16, SM204: 200 SM207, SM52: 500 ±1%, 2% ±50 Temperature Coefficient, PPM / ±5% ±100

Operating Temperature Range, -55 ~ +125 SM16 SM204 SM207 SM52 Film Temperature, 125 125 125 140

Insulation Resistance, MΩ >104

Performance Specifications Test Characteristics Test Conditions Limits

Short Time Overload IEC 60115-1 4.13 5 seconds 2.5x rated voltage (not over max. overload voltage) ±(0.5%+0.05R)

Load Life In Humidity IEC 60115-1 4.24 56 days at 40oC and 93% relative humidity ±(1.5%+0.05R)

Load Life 1,000 hours ±(0.25%+0.05R) Load Life 8,000 hours ±(0.5%+0.05R) Load Life 225,000 hours

IEC 60115-1 4.25.1 Rated load 1.5 hours ON, 0.5 hours OFF, at 70oC

±(1.5%+0.05R) Resistance To Soldering Heat

IEC 60115-1 4.18 10 seconds at 260oC solder bath temperature ±(0.5%+0.05R)

Solderability MIL-STD-202 Method 208 Solder area covered after 230+5oC/5+0.5 seconds w/ flux applied 95% Min.

Vibration IEC 60115-1 4.22 Six hours in each parallel and axial direction w/ a simple harmonic motion having an amplitude of 0.75mm and 10 to 500 Hz.

±(1%+0.1R)

Thermal Endurance IEC 60115-1 4.25.3 1000 hours at 125oC without load ±(0.5%+0.05R)

Thermal Shock IEC 60115-1 4.19 -55oC 30minutes, +125oC 30minutes, 5 cycles ±(0.5%+0.05R)

Ordering Information

Type Tolerance Temperature Coefficient

Resistance Value Packaging

Special Request

(Optional)

SM204 F (1%) G (2%) J (5%)

TK50 TK100

562R 84K5 1M69

B (Bulk) TR (Tape/Reel)

HV (High value)

SM - Stabilized Metal Film MELF Resistor · SM- Stabilized Metal Film MELF Resistor Specifications...

Documents

Transcript of SM - Stabilized Metal Film MELF Resistor · SM- Stabilized Metal Film MELF Resistor Specifications...