Sliding gates automation - EXPERT BULGARIA · Sliding gates automation. 400 kg 100 electronic 100...
Transcript of Sliding gates automation - EXPERT BULGARIA · Sliding gates automation. 400 kg 100 electronic 100...
Sliding gates automation
100 electronic400 kg
100
200
501 electronic
500 mechanical
801 electronic
800 mechanical
2001 electronic
2000 mechanical
500 kgresidential
300 kgcondominium
ONDA 800-801
50
200
800 kgresidential
500 kgcondominium
AT 80
200
800mechanical
mechanical
1200 kgresidential
800 kginten./cond.
ONDA 2000-2001
10002000 kg
AT 88T
8004000 kg
RESIDENTIAL CONDOMINIUM INTENSIVE INDUSTRIAL
The above mentioned data refer to carefully installed and regularly maintained products.
ONDA 424
100 electronic600 kg
ONDA 624
ONDA 500-501
SLIDING GATES
64
MAX.TYPE OF INSTALLATION
CYCLESCLUTCHWING WEIGHT DAY
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
3x0.75Ø
46 5 6
7
2
3
1
3x0.75Ø
3x0.75Ø
2x0.75Ø
2x1Ø
6Alc = 30mA
1.5Ø
inside
1 2
3
4
5
6
7
Gear motor with built-in electronic control unit with radio receiver on-board
Transmitter
Antenna 433,92 MHz
Flashing light
Pair of photocells
Control device
65
SLIDING GATES
WIRING DIAGRAM
ONDA 424
Service continuity guaranteed in case ofpower failure by an optional emergencybattery unit housed in the casing.
Complies with the current safety standardsas regard to obstacle detection and inversionof movement.Maximum anti-crush safety due to the elec-tronic torque adjustment combined withencoder technology, which also guaranteesa gradual approach during opening andclosing.
Easy to assemble and install thanks to opti-mised component layout and the muchlower height of the pinion from the ground.
POWER SUPPLY 230 Vac - 50/60 Hz
MOTOR POWER SUPPLY 24 Vdc
ABSORBED POWER 80 W
ABSORBED CURRENT 4,2 A
MAX. THRUST FORCE 450 N
MAX. LINEAR SPEED 10 m/min
OPERATING TEMPERATURE -20ºC to +55ºC
MAX. GATE WEIGHT 400 kg
HEIGHT OF PINION FROM GROUND 70 mm
GEAR MOTOR WEIGHT 9 kg
MAX. NO. CYCLES 100 cycles/day
PROTECTION CLASS IP 44Emergency release lever with customisedkey, for use during power supply failures.
Worm screw gear motor with permanentlubrication, aluminium body housing theelectronic control unit.Foundation plate height adjustable by theprovided screws.
TECHNICAL DATA
66
Low-voltage gear motor for sliding gates.Residential use up to 400 kg.
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index). AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
ONDA 424 400 kg 41101/001Gear motor with built-in control unit and radio receiver residential use
DESCRIPTION Max. gate width CODE
ONDA 424 gear motor with built-in control unit and radio receiver 1 41101/001
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
PC12E - Key switch for wall mounting 1 41830/007
ET2N - 24 V flashing light 1 41840/006
Aprimatic plastic rack with 5 metre steel core for use of up to a maximum of 500 kg 1 41180/052
IDEAL INSTALLATION Q.ty CODE
TR2 - 433.92 MHz twin-channel transmitter 41903/002
TR4 - 433.92 MHz four-channel transmitter 41903/004
ER4N - Pair of photocells 41812/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
Kit Antenna 433,92 MHz for ET2N/ET20N 41929/003
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 41180/053
Back up battery 41102/050
Battery charger card 41100/050
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
ONDA 424
67
OPERATOR DIMENSIONS
ONDA 624
68
Service continuity guaranteed in case ofpower failure by an optional emergencybattery unit housed in the guard.
Complies with the current safety standardsas regard to obstacle detection and inversionof movement.Maximum anti-crush safety due to the elec-tronic torque adjustment combined withencoder technology, which also guaranteesa gradual approach during opening andclosing.
Easy to assemble and install thanks to opti-mised component layout and the muchlower height of the pinion from the ground,and thanks to the eyelets and screws provi-ded with the foundation plates for a precisepositioning of the operator.
POWER SUPPLY 230 Vac - 50/60 Hz
MOTOR POWER SUPPLY 24 Vdc
ABSORBED POWER 80 W
ABSORBED CURRENT 4,2 A
MAX. THRUST FORCE 650 N
MAX. LINEAR SPEED 10 m/min.
OPERATING TEMPERATURE -20ºC to +55ºC
MAX. GATE WEIGHT 600 kg
HEIGHT OF PINION FROM GROUND 70 mm
GEAR MOTOR WEIGHT 9 kg
MAX. NO. CYCLES 100 cycles/day
PROTECTION CLASS IP 44Emergency release lever with customisedkey, for use during power supply failures.
Worm screw gear motor with permanent lubrication, aluminium body housing theelectronic control unit.
TECHNICAL DATA
Low-voltage gear motor for sliding gates.Residential use up to 600 kg,
condominium use up to 400 kg.
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
ONDA 624
69
OPERATOR DIMENSIONS
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
ONDA 624 600 kg 41102/001Gear motor with built-in control unit and radio receiver residential use
DESCRIPTION Max. gate width CODE
ONDA 624 gear motor with built-in control unit and radio receiver 1 41102/001
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
PC12E - Key switch for wall mounting 1 41830/007
ET2N - 24 V flashing light 1 41840/006
Aprimatic plastic rack with 5 m steel core for use of up to a maximum of 500 kg 1 41180/052
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 1 41180/053
IDEAL INSTALLATION Q.ty CODE
TR2 - 433.92 MHz twin-channel transmitter 41903/002
TR4 - 433.92 MHz four-channel transmitter 41903/004
ER4N - Pair of photocells 41812/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
Kit Antenna 433,92 MHz for ET2N/ET20N 41929/003
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 41180/053
Back up battery 41102/050
Battery charger card 41100/050
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
ONDA 500 - 501
Unbeatable silent running and functionalityfor residential applications up to 500 kg.Maximum reliability from a sturdy gear motor.
Anti-crush safety is ensured by a mechanicalclutch on the ONDA 500.
On the ONDA 501 anti-crush safety is provi-ded by the electronic control unit with built-in electronic torque control and provision forconnecting an auto-reverse card to reversegate direction in case of obstacles while clo-sing.
POWER SUPPLY 230 V - 50/60 Hz
ABSORBED POWER 230 W
THRUST FORCE 940 N (Z16)750 N (Z20)
LINEAR SPEED 9,5 m/min. (Z16)12,0 m/min. (Z20)
MAX. GATE WEIGHT 500 kg (Z16)300 kg (Z20)
OPERATING TEMPERATURE -20ºC to +70ºC
HEIGHT OF PINION FROM GROUND 70 mm
WEIGHT 10 kg
MAX. NO. CYCLES 100 cycles/day
PROTECTION CLASS IP 44
Z20 Pinion is available for the applicationthat need of faster operations speed.
T2E electronic control unit integrated in thegear motor (ONDA 501 only).
TECHNICAL DATA
Gear motor for sliding gates. Condominium use up to 300 kg,
residential use up to 500 kg.
70
Permanently lubricated worm gear withanodised aluminium body.
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
ONDA 501 EZ 16 1 41126/007Gear motor with built-in T2E control unit, with electronic torque control
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
Unico 433,92 MHz Memory System radio receiver with antenna included 1 41923/009
ET20N - 230 V flashing light 1 41841/009
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 1 41180/053
IDEAL INSTALLATION Q.ty CODE
ONDA 500 Z 16 500 kg residential use 41126/010Gear motor 300 kg condominium usewith mechanical cluth
ONDA 501 E Z 16 500 kg residential use 41126/007Gear motor with built in T2E control unit 300 kg condominium usewith electronic torque control
ONDA 500 E Z 16 SET 41126/008Gear motor with built-in T2E control unit with mechanical clutch
DESCRIPTION Max. gate width CODE
PF 501/801 - Foundation plate (pack of 4 pcs) 41126/051
Unico 433,92 MHz Memory System radio receiver with antenna included 41923/009
TR2 - 433.92 MHz twin-channel transmitter 41903/002
ER4N - Pair of photocells 41812/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
SB 500/800 - Personalised release key 41126/050
Aprimatic plastic rack with 5 metre steel core for use of up to a maximum of 500 kg 41180/052
ARC - Auto Reverse Card 41127/020
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
ONDA 500 - 501OPERATOR DIMENSIONS
71
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
Gear motor for sliding gates. Condominium use up to 500 kg,
residential use up to 800 kg.
ONDA 800 - 801
Maximum reliability thanks to the steel gearsin permanent lubrication.Maximum safety thanks to the electronicaltorque adjustment function.
POWER SUPPLY 230 V - 50/60 Hz
ABSORBED POWER 260 W
ABSORBED CURRENT 1.6 A
MAX. THRUST FORCE 1250 N (Z16)1000 N (Z20)
LINEAR SPEED 1250 N (Z16)1000 N (Z20)
OPERATING TEMPERATURE -20ºC to +70ºC
MAX. GATE WEIGHT 800 kg (Z16)500 kg (Z20)
OVERLOAD TEMPERATURE 90º C
HEIGHT OF PINION FROM GROUND 70 mm
WEIGHT 10 kg
MAX. NO. CYCLES 100 cycles/day
LUBRIFICANT TYPE AprimGREASE Vc 84
PROTECTION CLASS IP 44
Manual key release in the event of mainspower supply failure.
The gear motor is irreversible and thereforekeeps the gate locked.The use of other lock systems is thereforeeliminated.
Z20 Pinion is available for the applicationthat need of faster operations speed.
TECHNICAL DATA
72
Anti-crush safety is ensured by a mechanicalclutch on the ONDA 800.
On the ONDA 801 anti-crush safety is provi-ded by the electronic control unit with built-in electronic torque control and provision forconnecting an auto-reverse card to reversegate direction in case of obstacles whileclosing.
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
ONDA 801 E Z 16 1 41127/007Gear motor with built-in T2E control unit with electronic torque control
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
Unico 433,92 MHz Memory System radio receiver with antenna included 1 41923/009
ET20N - 230 V flashing light 1 41841/009
Aprimatic plastic rack with 5 metre steel core for use of up to a maximum of 500 kg 1 41180/052
IDEAL INSTALLATION Q.ty CODE
ONDA 800 Z 16 500 kg residential use 41127/009Gear motor with mechanical cluth 300 kg condominium use
ONDA 801 Z 16 41127/001Gear motor with electronic torque control
ONDA 801 E Z 16 41127/003Gear motor with built in T22E control unit and radio receiver with electronic torque control
ONDA 801 E Z 16 SET 500 kg residential use 41127/007Gear motor with built in T2E control unit 300 kg condominium usewith electronic torque control
ONDA 800 E Z 16 SET 41127/011Gear motor with built-in T2E control unit with mechanical clutch
DESCRIPTION Max. gate width CODE
PF 501/801 - Foundation plate (pack of 4 pcs) 41126/051
Unico 433,92 MHz Memory System radio receiver with antenna included 41923/009
TR2 - 433.92 MHz twin-channel transmitter 41903/002
ER4N - Pair of photocells 41812/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
SB 500/800 Personalised release key 41126/050
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 41180/053
ARC - Auto Reverse Card 41127/020
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
ONDA 800 - 801OPERATOR DIMENSIONS
73
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
NOTE: the lower gate wheels must not be too small for the weight of the structure (the minimum diameter of the wheels is 120 mm).
AT 80
Customised key lever emergency unlockingsystem to release the gate in the event of amains power failure and to protect againstunwanted entry.
Maximum reliability thanks to the steel gearsin oil bath.
Maximum safety thanks to the mechanicalanti-crush clutch system.Drive coupling and transmission are achievedusing a rack pinion.
POWER SUPPLY 230 V - 50/60 Hz
ABSORBED POWER 330 W
ABSORBED CURRENT 1.8 A
MAX. THRUST FORCE 1400 N (Z16) - 1120 N (Z20)
LINEAR SPEED 9.5 m/min.(Z16) - 12.0 m/min.(Z20)
OPERATING TEMPERATURE -20ºC to +70ºC
LUBRICANT QUANTITY 1.25 Lt
MAX. GATE WEIGHT (residential use) 1200 kg
OVERLOAD TEMPERATURE 90º C
HEIGHT OF PINION FROM GROUND 70 mm
WEIGHT 14 kg
MAX. NO. CYCLES 100 cycles/day
LUBRIFICANT TYPE AprimOil DN 22
PROTECTION CLASS IP 44
Anti-crush safety is ensured by an adjustableoil bath clutch which reduces the thrust forceof the gate in case of obstacles.
Oil bath gear motor with irreversible reduc-tion unit eliminating the need for additionallocking systems.
AT80 can be secured to the ground witheither a pivoting or fixed support. The pivo-ting support enables functioning even whenthe guide on the ground is not perfectly level-led thus preventing mechanical stress.
TECHNICAL DATA
Gear motor for sliding gates.Intensive use up to 800 kg,
residential use up to 1200 kg.
74
AT 80YZ 16 gear motor 1 41120/003
Pack for IF80 fixed installation 1 41120/051
T2E - Electronic control unit 1 41615/003
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
Unico 433,92 MHz Memory System radio receiver with antenna included 1 41923/009
ET20N - 230 V flashing light 1 41841/009
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 1 41180/053
IDEAL INSTALLATION Q.ty CODE
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
AT 80 YZ 16 800 kg intensive use 41120/003 Gear motor with 16 teeth rack and pitch 4 pinion,230 V - 50 Hz power supply, power 330 W 1200 kg residential usewith electro-mechanical limit switch, IF80 fixed installation required
DESCRIPTION Max. gate width CODE
PF80 - Foundation plate (pack 4 pieces) 41120/050
IB80 - Pivoting installation 41120/052
IF 80 - Fixed installation 41120/051
Unico 433,92 MHz memory System radio receiver with antenna included 41923/009
TR2 - 433.92 MHz twin-channel transmitter 41903/002
ER2N - Pair of photocells 41811/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
Aprimatic plastic rack pitch 4 complete with couplings (5 m) 41180/052
ARC - Auto Reverse Card 41127/020
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
NOTE: each installation needs one fixing kit IF80 or IB80.
AT 80OPERATOR DIMENSIONS
75
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
ONDA 2000 - 2001
Maximum reliability thanks to the steel gearsin permanent lubrication.
Potential risks should be carefully examinedfor all applications.Safety devices (photocells, straight safetyedges, etc.) should be added if necessary.
MOTOR POWER SUPPLY 230 V - 50/60 Hz
ABSORBED POWER 700 W
MAX. THRUST FORCE 2570 N
MAX. WING SPEED 9.5 m/min
OPERATING TEMPERATURE -20°C to +70°C
GATE WEIGHT from 1000 to 2000 kg
LIMIT SWITCH Electro-mechanical
PINION Z16
LUBRIFICANT TYPE AprimOil DN 22
PROTECTION CLASS IP 44
Drive coupling and transmission are achie-ved using a rack pinion.
Oil bath gear motor with irreversible reduc-tion unit eliminating the need for additionallocking systems.
TECHNICAL DATA
Gear motor for sliding gates of 1000 kg to 2000 kg.Intensive use.
76
Anti-crush safety is ensured by a mechanicalclutch on the ONDA 2000.
On the ONDA 2001 anti-crush safety is provi-ded by the electronic control unit with built-in electronic torque control and provision forconnecting an auto-reverse card to reversegate direction in case of obstacles whileclosing.
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
ONDA 2001 EZ 16 1 41125/005Gear motor with built-in T2E control unit, with electronic torque control
ER4N - Pair of photocells 1 41812/001
One TR2 - 433,92 MHz twin-channel transmitter 1 41903/002
Unico 433,92 MHz Memory System radio receiver with antenna included 1 41923/009
ET20N - 230 V flashing light 1 41841/009
Aprimatic galvanized rack pitch 4 complete with couplings 1 41180/053
IDEAL INSTALLATION Q.ty CODE
ONDA 2000 Z 16 2000 kg residential use 41125/007Gear motor with mechanical clutch and 16 tooth pinion 1000 kg condominium use
ONDA 2001 E Z 16 of 1000 kg 41125/005 Gear motor with built-in T2E control unit, to 2000 kgwith electronic torque control
DESCRIPTION Max. gate width CODE
PF 2000 - Foundation plate 41125/050
Unico 433,92 MHz Memory System radio receiver with antenna included 41923/009
TR2 - 433.92 MHz twin-channel transmitter 41903/002
ER4N - Pair of photocells 41812/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 2,0 m 41850/003
Straight safety edge 3,0 m 41850/004
Aprimatic galvanized rack pitch 4 complete with couplings 41180/053
ARC - Auto Reverse Card 41127/020
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
ONDA 2000 - 2001OPERATOR DIMENSIONS
77
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08
AT 88T
Maximum power and reliability for heavy-duty use.
Customised key emergency unlocking sy-stem to release the gate in the event of amains power failure and to protect againstunwanted entry.
POWER SUPPLY Three-phase 220/380 V - 50/60 Hz
ABSORBED POWER 960 W
MAX. ABSORPTION (at 380 V) 2.6 A
OPERATING TEMPERATURE -20ºC to +70ºC
DRIVE FORCE 9 m/min.
MAX. GATE WEIGHT 4000 kg
PINION MODULE 4 mm
PINION Z22
EXTERNAL DIMENSIONS (LxDxH) 365 x 266 x 600
PROTECTION CLASS IP 44
Potential risks should be carefully examinedfor all applications. Safety devices (photo-cells, straight safety edges, etc.) should beadded if necessary.
AT 88T can be combined with A 88 E, electro-nic control unit supplied in a sealed Apri-matic (IP55) container and 4 functioninglevels: automatic, semi-automatic, rapidautomatic and dead man.
TECHNICAL DATA
Gear motor for sliding gates up to 4000 kg. Intensive use.
78
NOTE: for control and safety devices and installation accessories, see section “Electronic devices and installation accessories” in this catalogue (consult the index).
AT 88T 4000 kg 41124/001 Gear motor with 22 teeth rack and pinion drive 4,230/380 V 50 Hz three-phase power supply, motor power 920 W, foundation plate included
DESCRIPTION Max. gate width CODE
AT 88T Gear motor 1 41124/001
A88E - Electronic control unit supplied in a sealed Aprimatic (IP55) container and 4 functioning levels: 1 41615/005 automatic, semi-automatic, rapid automatic (0.5 sec. pause for parking access) and dead man, suitable for an operator with max. power of 1200 W (1.5 Hz), three-phase (230/380 V - 50/60 Hz) or single-phase (230 V - 50/60 Hz)
ER2N - Pair of photocells 2 41811/001
Unico 433.92 MHz Memory System radio receiver with antenna included 1 41923/009
TR2 - 433.92 MHz twin-channel transmitters 1 41903/002
ET 22 - 230 V flashing light 1 41841/001
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 1 41180/053
Straight safety edge 2,0 m 2 41850/003
IDEAL INSTALLATION Q.ty CODE
Unico 433.92 MHz Memory System radio receiver with antenna included 41923/009
TR2 - 433.92 MHz twin-channel transmitter 41903/002
ER2N - Pair of photocells 41811/001
PC12E - Key switch for wall mounting 41830/007
CAL - Aluminium column for the ER4N photocells 41812/050
433,92 MHz antenna 41929/001
Straight safety edge 1,5 m 41850/002
Straight safety edge 3,0 m 41850/003
Aprimatic galvanized rack pitch 4 complete with couplings (5 m) 41180/053
DESCRIPTION OF OPTIONAL ACCESSORIES CODE
AT 88TOPERATOR DIMENSIONS
79
AP
RIM
AT
IC ®
> V
ALI
DIT
Y 0
9/20
08