SL4200 - Midland MFG · Trailer Location: At the front of the trailer. Notes: This washer is used...
Transcript of SL4200 - Midland MFG · Trailer Location: At the front of the trailer. Notes: This washer is used...
Parts No: 3100097
Description: Air Tank (Medium)
Trailer Location:
Notes:
Parts No: 3100096
Description: Air Tank (Small)
Trailer Location:
Notes:
Parts No: 3100231
Description: 5 Port 4 Way Gate Valve
Trailer Location: Rear drivers side
Notes: This valve operates the gates and is equipped with a manual over ride. This valveis normally closed.
Parts No: 3100361
Description: 5 Port 4 Way Control Valve
Trailer Location:
Notes: This valve dumps the air in the suspension and is equipped with a manual override. This valve is normally open.
Parts No: 3100147
Description: Air Control Kit
Trailer Location:
Notes: This air control kit is the manual dump valve on the trailer.
AIR
Over rear suspension
Over rear suspension
SL4200
Rear drivers side
Rear suspension
Parts No: 3100118
Description: Quick Release Valve
Trailer Location:
Notes: This valve provides a direct air exhaust to speed up the air suspension dump
Part No: 3100117
Description: Spring Brake Control Valve
Trailer Location:
Notes:
Part No: 3100194
Description: 6 Port ABS Relay Valve
Trailer Location: This valve is attached to the brake system reservoir tank over the rearsuspension.
Notes:
Part No: 3100373
Description: 3" Composite Cylinder
Trailer Location:
Notes: Starting in April 2007 Midland end dump trailers are using individual compositecylinders mounted in each gate post instead of the old style trip with thecentrally mounted air pod. This is the 3" composite cylinder used in the new trip.
Part No: 3100122
Description: Brake Chamber
Trailer Location: At the rear of the trailer under the body
Notes: This brake chamber is part of the old style gate trip used prior to April 2007. It controls the opening of the gate.
function.
This valve is attached to the brake system reservoir tank over the rearsuspension.
Inside gate post
On the Inside of the chassis, near the center of the trailer.
Parts No: 3500371
Description: PLC Select Relay Valve
Trailer Location: This valve is attached to the brake system reservoir tank over the rearsuspension.
Notes: This valve controls the ABS function of the trailer.
Part No: 3500221
Description: 7 Wire Pole Plug
Trailer Location: At the front of the trailer
Notes: This plug supplies power to the trucklite harness on the trailer.
Part No: 3500022
Description: 7-Pole Plug w/ Guard
Trailer Location: At the front of the trailer
Notes: This plug supplies power to all auxiliary functions on the trailer.
ELECTRICAL
Part No: 3900180
Description: Tailgate Tightener Assembly
Trailer Location: At the rear of the trailer
Notes: This tailgate tightener are used to seal the gate closed.
Part No: 3900258
Description: Rubber seal (P Seal)
Trailer Location: At the rear of the trailer
Notes: This rubber seal is used to insure a water tight tailgate seal.
Part No: 3900066
Description: Rubber Spring ( LARGE )
Trailer Location:
Notes: This rubber spring lifts the body off the frame during empty travel
Part No: 3900307
Description: Gate Hinge Pin
Trailer Location: Top hinge of the gate
Notes:
Part No: 3900315
Description: Top Cylinder Pin (18.5")
Trailer Location: On the cylinder; at the front of the trailer
Notes: This cylinder pin is used to secure the top of the cylinder.
BODY
At the base of the "A" frame in the front of the trailer.
Part No: 6021034
Description: Hyva Cylinder Pin (18.83)
Trailer Location:
Notes: This cylinder pin is used to secure the top of the cylinder. It is only used onHyva cylinders.
On the cylinder; at the front of the trailer
Part No: 3900194
Description: Galvanized Fender (66")
Trailer Location:
Notes:
Part No: 3900329
Description: Black Poly Fender
Trailer Location:
Notes:
Part No: 6021268
Description: Left Trip Weldment
Trailer Location:
Notes: Starting in April 2007 Midland end dump trailers are using individual compositecylinders mounted in each gate post instead of the old style trip with the spring and air pod. This is the trip weldment that this composite cylinder(3100373) mounts to.
Part No: 6021269
Description: Right Trip Weldment
Trailer Location:
Notes: Starting in April 2007 Midland end dump trailers are using individual compositecylinders mounted in each gate post instead of the old style trip with the spring and air pod. This is the trip weldment that this composite cylinder(3100373) mounts to.
Part No: 4027552
Description: Latch Finger
Trailer Location:
Notes: Starting in April 2007 Midland end dump trailers are using individual compositecylinders mounted in each gate post instead of the old style trip with the spring and air pod. This latch finger is used in the new trip.
CHASSIS
Right and left rear of trailer
Right and left rear of trailer
Inside gate post
Inside gate post
Inside gate post
Part No: 6021277
Description: Trip Pin
Trailer Location:
Notes: Starting in April 2007 Midland end dump trailers are using individual compositecylinders mounted in each gate post instead of the old style trip with thespring and air pod. This is the trip pin used to secure the composite cylinder(3100373) to the trip weldment.
Part No: 6016854
Description: Left Bracket Trip Weldment
Trailer Location: Inside the gate post
Notes: This is the trip weldment that was used prior to April 2007 and used to mount the air pod inside the gate post.
Part No: 6016856
Description: Right Bracket Trip Weldment
Trailer Location: Inside the gate post
Notes: This is the trip weldment that was used prior to April 2007 and used to mount the air pod inside the gate post.
Part No: 3900117
Description: Springs For Air Trip
Trailer Location:
Notes: This is the spring used in the gate trip prior to April 2007.
Part No: 4024914
Description: Latch Finger
Trailer Location: Inside the gate post
Notes: This is the latch used in the gate trip prior to April 2007.
Inside gate post
Inside the gate post
Part No: 6015876
Description: Clevis Weldment
Trailer Location: Inside the gate post
Notes: This clevis weldment is used on the trip prior to April 2007. It is used to securethe brake chamber (3100122) to the trip weldment (601854/56)
Part No: 3900028
Description: Machined Rod End (1/2")
Trailer Location:
Notes: This rod end is used to hold the spring in place in the old gate trip used prior to April 2007.
Part No: 3900232
Description: Clevis Pin
Trailer Location:
Notes: This clevis pin is used to secure the latch finger (3900232) to the trip weldment(6016854/56) in the old gate trip used prior to April 2007.
Part No: 6015825
Description: Hinge Assembly
Trailer Location:
Notes:
Part No: 3900320
Description: Hinge Pin (9.13")
Trailer Location:
Notes: This pin is used in the hinge assembly (6015825)
Inside gate post
At the rear of the trailer
At the rear of the trailer
At the rear of the trailer under the body
Part No: 3900316
Description: Bottom Cylinder Pin (19.75")
Trailer Location: On the cylinder
Notes: This cylinder pin is used to secure the bottom of the cylinder.
Part No: 4027167
Description: Dump Valve Mounting Bracket
Trailer Location:
Notes: This bracket is attached to inside rear frame and mounts the 5 port dump valve (3100363).
Part No: 6019555
Description: Hinge Bushing
Trailer Location:
Notes: This bushing contains 3 composite bearings (3912877). It is used to mount thehinge assembly (6015825).
Part No: 3912877
Description: Composite Bearing (2.01 x 1.51)
Trailer Location:
Notes: This is a greaseless bearing that is installed in the hinge assembly bushings(6015285/6016688).
Part No: 3900240
Description: Composite Bearing (1.25" x 1.435")
Trailer Location:
Notes: This is a greaseless bearing that fits inside the gate hinge assembly welded tothe body.
Rear drivers side inside the frame of trailer
At the rear of the trailer
Inside the bushings of the hinge assembly
Inside the gate hinge assembly at the rear of the trailer
Part No: 6019965
Description: Light Bar
Trailer Location: At the rear of the trailer
Notes:
Part No: 3900335
Description: Control Box
Trailer Location: At the front of the trailer
Notes: This control box holds the dump valve (3100361) and the gate over ridevalve (3100231).
Part No: 4023970
Description: Light Bar Shed
Trailer Location: At the rear of the trailer
Notes: This light bar shed is used to protect the light bar (6019965) at the rear ofthe trailer.
Part No: 4023945
Description: Light Bar Shed
Trailer Location: At the rear of the trailer
Notes: This light bar shed is used to protect the light bar (6019965) at the rear ofthe trailer.
Part No: 5012025
Description: Mud Flap Strip Backing
Trailer Location:
Notes: This bracket is to secure all mud flaps to the trailer.
On all trailer mounted mud flaps
Part No: 3900022
Description: Midland Mud Flap (24" x 30")
Trailer Location:
Notes:
Part No: 3900020
Description: Black Mud Flap (24" x 30")
Trailer Location:
Notes:
At the rear of the trailer
At the Front or middle of the trailer
Part No: 3900117
Description: Hitch Springs
Trailer Location: At the front of the trailer
Notes: This spring is used on the hitch of the trailer to give tension on the hitch making it easier to lift and adjust.
Part No: 4011915
Description: Washer
Trailer Location: At the front of the trailer
Notes: This washer is used to secure the pintle eye (3900012) onto the hitch.
Part No: 3900017
Description: Neoprene Bushing
Trailer Location: At the front of the trailer
Notes: This is the bushing used on the pintle eye (3900012).
Part No: 3900012
Description: Pintle Eye
Trailer Location: At the front of the trailer
Notes:
Part No: 6021213
Description: Jack Assy.
Trailer Location: At the front of the trailer
Notes: This jack is used on the hitch and is used to adjust the hitch to yourdesired height.
HITCH