SKYROS iView -...

V1.0

2013-01-04

SKYROS SERIES

ANDROID APP Mobile Phones and Tablets

SKYROS iView

Setup Guide :

Internet browsing on smartphones

(This Guide applies to all Hardware Versions of DG-BG4011N)

SETUP GUIDE

SKYROS iView Android App for IP Camera

(This guide applies to DG-SC2100, DG-SC2100W, DG-SC2600, DG-SC2600W,

DG-SC3630 and DG-SC3610W)

SETUP GUIDE SKYROS iView Android APP

COPYRIGHT

Copyright © 2013 by this company. All rights reserved. No part of this publication may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language

or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,

chemical, manual or otherwise, without the prior written permission of this company This company

makes no representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs

prove defective following their purchase, the buyer (and not this company, its distributor, or its

dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or

consequential damages resulting from any defect in the software. Further, this company reserves

the right to revise this publication and to make changes from time to time in the contents thereof

without obligation to notify any person of such revision or changes.

Trademarks

DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property

of the respective manufacturers.


SKYROS iView is an user friendly IP camera app, ideal for monitoring your home or office remotely using

a 3G or any Wi-Fi Internet connection*. It is extremely easy & convenient to connect to your network

camera in just a few simple steps and access it remotely using a smartphone, tablet, or computer no

matter where you are.

Features of the SKYROS iView App:

User Friendly Installation

Live viewing from any 3G or Wi-Fi Internet connection*

Remote pan and tilt control**

Take snapshot remotely

Adjust brightness, saturation and sharpness settings

Remotely view/control up to 12 IP Camera

Note:-

1. The SKYROS iView app requires an Android phone or tablet running version 2.3 or above.

2. * For remote viewing of IP Camera you need to have a Static Public IP or DDNS configured on

the IP Camera.

3. ** For pan/tilt supported models (DG-SC3630 and DG-SC3610W) only.

To install SKYROS iView application, launch “Market/ Google Play Store” (In your Android device tap ‘All

Apps’ menu).

Step 1 :


Click ‘magnifier icon’ at upper-right corner of Android market, and input ‘Skyros iView’ in search field.

You should be able to search the SKYROS iView App (If not, please check the spelling again).

Step 2 :


Tap on the “Install” button to download & install Skyros iView App.

Once you tap “Install’, Android will prompt you to confirm installation, please tap “Accept &

Step 3 :

Step 4 :


Download” button below to start installation.

Please be patient while the application is getting installed.

Once the application is installed, tap on “Open” to launch the Skyros iView utility.

Step 5 :


You can also launch the ‘Skyros iView’ APP from the ‘All Applications’, please refer the below screen for

more detail.

Launch the utility by clicking on Skyros iView icon in the menu option.

Step 6 :


Once you launch the app; Skyros iView will search for all DIGISOL IP camera in your network.

Ensure that your Android device is wirelessly connected to same wireless access point to which the

DIGISOL IP camera’s are connected. Below screen displays the list of IP Camera detected in the network.

Step 7 :


Once the IP cameras are detected on Auto-discovery, select the IP camera. It will prompt you to input

the IP camera password.

After entering the password, tap on “OK”. Similarly you can add any additional IP cameras in your

network. You will see a green check mark against the added IP camera.

Step 8 :


If you wish to add an IP camera from Internet then please tap “Add Manually” button to setup IP

camera manually.

In this page, you can input IP camera’s parameters manually:

Camera Name: You can define a name for this IP camera for easy identification.

IP Address/ DDNS: Here, you can enter an IP Addres or a DDNS URL of an IP camera if any.

Port: Enter the HTTP port of an IP camera. Default port is 80.

User Name: Input the user name of IP camera. Default user name is ‘admin’

Password: Input the password of IP camera. Default password is ‘1234’

Tap “Add” to add to proceed.

Step 9 :


When an IP camera has been added successfully, it will be listed under Settings tab.

To change the sequence of live view of an IP camera, you can tap icon


To remove/ delete an IP camera, tap and hold the desired camera in the list. It will then prompt with a

message as shown below; tap “Yes” to delete the camera:-

You can view 4 camera’s at a time using this application.

Live / Remote Monitoring


To view a particular camera in full screen, tap on that camera’s view.

Three icons will be displayed on the bottom of the image.

: Tap this icon to set the brightness, saturation & sharpness values of an IP camera.

: Tap this icon to capture the snapshot of current view of an IP camera. You will see ‘Save

Snapshot’ message appear, that indicates a snapshot has been taken.

: This icon will be highlighted/active if the connected IP camera supports Pan/Tilt. You can tap

this icon and this symbol will appear on the video displayed by the IP camera. You can slide on the live

video to move the camera in the direction you wish to move.


You can view the current version of Skyros iView under About tab.

Note: If you slide from top to bottom on the video display screen, it shows a single view. If you slide

twice, it shows a two screen view. If you slide for third time, it shows a quad view in the application.

SKYROS iView -...

Documents

Transcript of SKYROS iView -...