SKM C65921022416400

N

2019 LIGHTING DESIGN

VICINITY MAP

262 Katonah Ave, Katonah, NY10536

WELLS FARGO

THIS PLAN SET IS PROPRIETARY AND CONFIDENTIAL INFORMATION OF WELLS FARGO AND THE USE OF THIS DESIGN IS PROHIBITED WITHOUT THE EXPRESS PERMISSION OF WELLS FARGO

DRAWING INDEX:

-

LU-1

LU-2

LU-3

LU-4

LU-5

LU-6

COVER SHEET

GENERAL NOTES

LUMINAIRE SCHEDULE

OVERALL SITE PLAN

FULL SITE PHOTOMETRICS

FIXTURE REMOVAL & DIMENSIONING PLAN

ATM COMPLIANCE AREA PHOTOMETRICS PLAN - FOR BANK USE ONLY

www.gmr1.com

Office: (972) 771-6038

1629 Smirl Drive, Suite 200, Heath, Texas 75032

v5 201203

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

Katonah, NY

141510

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

31 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

LU-1

GENERAL NOTES

WELLSFARGO

DESCRIPTIONREVISIONNO.

1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

v5 201203

GENERAL NOTES:

1. EXISTING CONDITIONS SHOWN ON THE DRAWINGS ARE BASED ON A LIMITED AMOUNT OFINFORMATION AVAILABLE TO THE ENGINEER. ALL SUCH CONDITIONS SHALL BE VERIFIED BYTHE CONTRACTOR PRIOR TO SUBMITTING THE BID AND ADJUSTED IF NECESSARY. NOADDITIONAL COMPENSATION SHALL BE GRANTED AFTER AWARDING A BID FOR ANYEQUIPMENT, MATERIAL OR LABOR REQUIRED TO REWORK OR OTHERWISE MODIFY EXISTINGCONDITIONS.

2. THIS LIGHTING DESIGN IS BASED ON A COMBINATION OF STATE STANDARDS, THE BANK'SCURRENT SECURITY POLICY FOR EXTERIOR ATM AND AFTER-HOUR DEPOSITORIES AND BANKGUIDELINES FOR NON-SECURITY COMPLIANCE ZONES.

3. TRIM ALL TREES/LANDSCAPING TO MINIMIZE IMPEDING LIGHT FROM ANY LIGHT FIXTURESTHAT IMPACT THE 60' RADIUS AROUND ALL ATMS AND A RADIUS OF 50' AROUND ALLAFTER-HOUR/NIGHT DEPOSITORIES. CONSIDERATION MUST BE GIVEN TOTREES/LANDSCAPING IN A STATE OF FULL FOLIAGE/BLOOM AND FUTURE GROWTH. ALLLANDSCAPING WORK WILL BE PERFORMED BY OTHERS WITH A SEPARATE PERMIT (IFREQUIRED).

4. ALL MOUNTING HEIGHTS ARE INTENDED TO THE BOTTOM OF THE FIXTURE.5. CONTRACTOR TO FIELD VERIFY FIXTURE PLACEMENT DIMENSIONS PRIOR TO CONSTRUCTION.6. DIMENSIONING PROVIDED IS FOR PROPOSED FIXTURE LOCATIONS ONLY, UNLESS OTHERWISE

NOTED ON THE DRAWING.7. THE CONTRACTOR SHALL ATTEMPT TO ELIMINATE THE USE OF EXPOSED CONDUIT WHERE

POSSIBLE. IF EXPOSED CONDUIT IS NECESSARY, THE CONTRACTOR SHALL VERIFY USE WITHPROJECT MANAGER.

8. THE CONTRACTOR SHALL VERIFY THAT LIGHT POLES FOR PROPOSED OR MODIFIED FIXTURESARE ADEQUATE FOR THE INTENDED MOUNTING HEIGHT. IF AN EXISTING LIGHT POLE IS BEINGUSED, THE CONTRACTOR SHALL VERIFY THAT IT IS IN SATISFACTORY CONDITION. A TYPICALPOLE BASE DETAIL (AS PER EACH STATE) WILL BE PROVIDED BY GMR FOR EACH SITE. IF A SITESPECIFIC POLE BASE DETAIL IS REQUIRED, THIS WILL BE COORDINATED BY THE CONTRACTORAND WILL FOLLOW ANY APPLICABLE STATE OR LOCAL JURISDICTION STANDARDS.

FIXTURE CLARIFICATION NOTES:

1. GMR MAY COMBINE OR ADD TO NOTES AS NEEDED IN ORDER TO CLARIFY FURTHER.2. OUT OF SCOPE - EXISTING FIXTURES TO REMAIN ON SITE WITHOUT MODIFICATION. NO

ACTION REQUIRED UNLESS NOTED OTHERWISE.3. REMOVE AND PATCH - EXISTING FIXTURES TO BE FULLY REMOVED AND ANY PAINTING,

PATCHING OR ELECTRICAL WORK NEEDED IS TO BE ASSESSED AND PERFORMED BY GC.4. REPLACE EXISTING FIXTURE - EXISTING FIXTURE TO BE FULLY REMOVED AND REPLACED IN

THE SAME LOCATION WITH A NEW FIXTURE. GC TO VERIFY IF POLE AND/OR POLE BASE ISSUFFICIENT FOR THE NEW FIXTURES. ANY PAINTING, PATCHING OR ELECTRICAL WORKNEEDED IS TO BE ASSESSED AND PERFORMED BY GC.

5. ADD NEW FIXTURE - NEW FIXTURES TO BE ADDED. ANY PAINTING, PATCHING OR ELECTRICALWORK NEEDED TO BE ASSESSED AND PERFORMED BY GC.

6. ADD NEW POLE & FIXTURE - A NEW POLE AND FIXTURE TO BE ADDED. GC TO SPECIFY POLETO MATCH EXISTING STYLE AND COLOR AND, IF NOT PROVIDED, POLE BASE DATA FOR NEWPOLE LOCATIONS. GC TO VERIFY IF POLE AND POLE BASE IS SUFFICIENT FOR THE HEIGHT,LOCATION AND FIXTURE SPECIFIED.

7. GMR DOES NOT SPECIFY MOUNTING HARDWARE FOR ANY SPECIFIED FIXTURES. GC ISTO WORK WITH DISTRIBUTOR AND/OR MANUFACTURER ON A CASE BY CASE BASIS TOIDENTIFY AND ORDER REQUIRED MOUNTING HARDWARE.

8. GC TO VERIFY WHETHER EXISTING WIRING LOCATIONS OR THE ADDITION OF WIRING FORNEW FIXTURE LOCATIONS IS SUFFICIENT FOR THE DESIGNATED FIXTURE LOCATION.

9. GC TO SPECIFY POLE COLOR AND TYPE PRIOR TO ORDERING.10. ALL FIXTURES ARE ASSUMED BRONZE IN COLOR UNLESS NOTED OTHERWISE IN THE

LUMINAIRE SCHEDULE. GC TO CONFIRM PRIOR TO ORDERING.

SITE ABBREVIATIONS:

= PROPERTY LINE

= ABOVE FINISHED GRADE

= FOOTCANDLE

= CONTROLLED BY OTHERS

= AFTER HOUR DEPOSITORY

PL

AFG

Fc

CBO

AHD

CONTRACTOR RESPONSIBILITIES:

1. CONTRACTOR SHALL BE RESPONSIBLE FOR PERMITTING, INCLUDING COORDINATION WITHTHE LOCAL JURISDICTION AND ANY ASSOCIATED PERMIT FEES OR PROCESSING.

2. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL PERMITTING DOCUMENTS THAT ARE NOTINCLUDED IN THE LIGHTING DESIGN PACKAGE.

3. CONTRACTOR IS REQUIRED TO RECYCLE ALL LAMPS AND BALLASTS WHEN SUCHREPLACEMENT IS REQUIRED.

4. CONTRACTOR SHALL VERIFY VOLTAGE REQUIREMENTS FOR FIXTURES PRIOR TOPLACEMENT OF FIXTURE ORDERS.

5. CONTRACTOR TO VERIFY LIGHTING CONTROLS PRIOR TO BEGINNING CONSTRUCTION. SEELIGHTING CONTROL NOTES.

6. CONTRACTOR SHALL RECEIVE FORMAL APPROVAL FROM GMR ON ANY FIXTUREMODIFICATIONS OR VARIATIONS FROM THE LUMINAIRE SCHEDULE.

7. CONTRACTOR SHALL VERIFY EXISTING AND PROPOSED FIXTURE MOUNTING CONDITIONS INFIELD. ANY SPECIAL MOUNTING HARDWARE NEEDED FOR PROPOSED FIXTURES SHALL BETHE RESPONSIBILITY OF THE CONTRACTOR.

8. CONTRACTOR SHALL SUPPLY ALL NEW LIGHT POLES. NEW LIGHT POLES SHALL MATCHEXISTING CONDITIONS ON SITE FOR POLE TYPE AND PAINT COLOR.

9. CONTRACTOR SHALL PERFORM ALL NECESSARY PATCHING OR REPAINTING FOR ADDED,REMOVED, OR REPLACED FIXTURES.

10. CONTRACTOR SHALL REPAIR ANY DISTURBED AREAS BACK TO EXISTING CONDITIONINCLUDING PAVED AREAS, LANDSCAPED AREAS, ETC.

11. EXPOSED CONDUIT (ONLY WHERE IT CANNOT BE CONCEALED) SHALL BE PAINTED TOMATCH THE BACKGROUND SURFACE COLOR.

12. CONTRACTOR SHALL VERIFY AND DOCUMENT COMPLETED WORK DURING NIGHT HOURS.ALL FIXTURES (INCLUDING OUT OF SCOPE FIXTURES) MUST BE FUNCTIONAL DURING NIGHTHOURS PRIOR TO SCHEDULING A FINAL SURVEY WITH GMR.

13. CONTRACTOR SHALL PROVIDE BEFORE AND AFTER NIGHT TIME PHOTOS OF THE SITE.14. CONTRACTOR SHALL RECEIVE A PUNCHLIST FROM GMR UPON FINAL SURVEY FOR ANY

REMAINING ITEMS TO BE COMPLETED.15. NEW LIGHT FIXTURES IN NEW LOCATIONS ARE TO BE MOUNTED IN THE INSTALL RANGE

SET BY GMR ON THE DESIGN DOCUMENTS.§ ALL FIXTURES MOUNTED TO COLUMNS OR WALLS LESS THAN 5 FEET WIDE

ARE TO BE CENTERED.§ ALL FIXTURE COLORS AND STYLE AND LUMEN OUTPUT ARE TO BE AS

REQUIRED BY GMR WITH NO SUBSTITUTIONS WITHOUT GMR APPROVAL.§ CONDUIT AND BOXES ARE TO BE FULLY CONCEALED IN ALL WALLS, SOFFITS

AND COLUMNS THAT ARE NOT A PART OF THE BUILDING STRUCTURE OR OFMASONRY THICKER THAN 6 INCHES.

§ ALL EXPOSED CONDUIT AND BOXES LOCATED IN AREAS WHERE VISIBLE TOTHE PUBLIC SHALL BE PAINTED TO MATCH THE COLOR OF ITS SURROUNDINGSURFACES.

16. ALL FIXTURE REPLACEMENT FOR EXISTING FIXTURE LOCATIONS SHALL FULLY COVER ALL OFTHE MOUNTING SURFACE EXPOSED BY THE REMOVAL OF THE EXISTING FIXTURE, SHOULDTHE NEW FIXTURE NOT ENTIRELY COVER THE EXPOSED SURFACE THEN A BEAUTY PLATE ISTO BE INSTALLED BEHIND THE NEW FIXTURE.

§ IF A BEAUTY PLATE IS NOT AN OPTION, THEN THE FIXTURE INSTALLER WILLPAINT OR RESURFACE THE EXPOSURE TO MATCH AND TO THE SATISFACTIONOF W.F. OR THE BUILDING MANAGEMENT CO.

17. ALL REMOVED FIXTURES SHALL HAVE LAMPS AND BALLASTS RECYCLED AS REQUIRED BYWF.

18. ALL DEBRIS CAUSED BY THE REQUIRED SCOPE OF WORK SHALL BE REMOVED FROM THESITE DAILY AT THE END OF THE WORKDAY.

19. NO MATERIALS OR EQUIPMENT ARE TO BE STORED ON SITE OVERNIGHT OR WEEKENDS.20. WORK DURING BUSINESS HOURS AND AFTER-HOURS MUST BE APPROVED BY THE PPM.21. ACCESS INTO THE BUILDING AND TO ELECTRICAL EQUIPMENT WILL BE AT THE DIRECTION

OF THE STORE MANAGER OR PPM.22. THE INSTALL CONTRACTOR SHALL ABIDE BY ALL FEDERAL, STATE AND/OR LOCAL CODES. IF

A DISCREPANCY BETWEEN CODES OCCURS, THE MOST STRINGENT SHALL PREVAIL.23. ALL CONDUCTORS SHALL BE SIZED ACCORDING TO 2011 NEC OR LATEST VERSION.24. ALL NEUTRALS SHALL BE CONSIDERED CURRENT-CARRYING CONDUCTORS ACCORDING TO

2011 NEC OR LATEST VERSION.

LIGHTING CONTROL NOTES:

THE CONTRACTOR SHALL VERIFY THE CONTROLS FOR ALL EXTERIOR LIGHTING ON THE SITE (EXCLUDINGSIGNAGE) AND ADJUST ACCORDING TO THE FOLLOWING:

· PHOTOCELL CONTROL:

CONTRACTOR SHALL REPLACE EXISTING PHOTOCELLS WITH NEW AND INSTALL IN A LOCATION BESTSUITED TO PROVIDE APPROPRIATE LIGHT EXPOSURE SUCH THAT EXTERIOR LIGHTS ARE ON ALL HOURSOF DARKNESS.

· TIME CLOCK CONTROL:

CONTRACTOR SHALL VERIFY TIME CLOCK IS SET PROPERLY AND LEAVE CIRCUIT ON TIME CLOCKCONTROL.

· MANUAL CONTROL:

CONTRACTOR SHALL VERIFY THAT NO EXTERIOR LIGHTING IS CONTROLLED MANUALLY. IF ANYEXTERIOR LIGHTING IS ON A MANUALLY CONTROLLED CIRCUIT, CONTRACTOR SHALL ADJUST TO BECONTROLLED BY PHOTOCELL.

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

32 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

NOTE: THIS LIGHTING PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM THIS LIGHTING PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM THIS LIGHTING PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM LIGHTING PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM LIGHTING PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM PLAN ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM ILLUSTRATES ILLUMINATION LEVELS CALCULATED FROM ILLUMINATION LEVELS CALCULATED FROM ILLUMINATION LEVELS CALCULATED FROM LEVELS CALCULATED FROM LEVELS CALCULATED FROM CALCULATED FROM CALCULATED FROM FROM FROM LABORATORY DATA UNDER CONTROLLED CONDITIONS IN ACCORDANCE WITH DATA UNDER CONTROLLED CONDITIONS IN ACCORDANCE WITH DATA UNDER CONTROLLED CONDITIONS IN ACCORDANCE WITH UNDER CONTROLLED CONDITIONS IN ACCORDANCE WITH UNDER CONTROLLED CONDITIONS IN ACCORDANCE WITH CONTROLLED CONDITIONS IN ACCORDANCE WITH CONTROLLED CONDITIONS IN ACCORDANCE WITH CONDITIONS IN ACCORDANCE WITH CONDITIONS IN ACCORDANCE WITH IN ACCORDANCE WITH IN ACCORDANCE WITH ACCORDANCE WITH ACCORDANCE WITH WITH WITH ILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA (IESNA) APPROVED ENGINEERING SOCIETY OF NORTH AMERICA (IESNA) APPROVED ENGINEERING SOCIETY OF NORTH AMERICA (IESNA) APPROVED SOCIETY OF NORTH AMERICA (IESNA) APPROVED SOCIETY OF NORTH AMERICA (IESNA) APPROVED OF NORTH AMERICA (IESNA) APPROVED OF NORTH AMERICA (IESNA) APPROVED NORTH AMERICA (IESNA) APPROVED NORTH AMERICA (IESNA) APPROVED AMERICA (IESNA) APPROVED AMERICA (IESNA) APPROVED (IESNA) APPROVED (IESNA) APPROVED APPROVED APPROVED METHODS. ACTUAL SITE ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES ACTUAL SITE ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES ACTUAL SITE ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES SITE ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES SITE ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES ILLUMINATION LEVELS AND PERFORMANCE OF LUMINARIES LEVELS AND PERFORMANCE OF LUMINARIES LEVELS AND PERFORMANCE OF LUMINARIES AND PERFORMANCE OF LUMINARIES AND PERFORMANCE OF LUMINARIES PERFORMANCE OF LUMINARIES PERFORMANCE OF LUMINARIES OF LUMINARIES OF LUMINARIES LUMINARIES LUMINARIES MAY VARY DUE TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN VARY DUE TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN VARY DUE TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN DUE TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN DUE TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN TO VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN VARIATIONS IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN WEATHER, ELECTRICAL VOLTAGE, TOLERANCE IN ELECTRICAL VOLTAGE, TOLERANCE IN ELECTRICAL VOLTAGE, TOLERANCE IN VOLTAGE, TOLERANCE IN VOLTAGE, TOLERANCE IN TOLERANCE IN TOLERANCE IN IN IN LAMPS AND OTHER RELATED VARIABLE FIELD CONDITIONS.

FARGO

LU-2

LUMINAIRE SCHEDULE

WELLS

BLUEGREEN

ORANGE

= NEW FIXTURE= EXISTING FIXTURE LOCATION TO BE REPLACED= EXISTING FIXTURE TO REMAIN= FIXTURE TO BE REMOVEDTURQUOISE

PINK = REPLACE WITH NEW POLE AT NEW HEIGHT


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

v5 201203

LUMINAIRE SCHEDULE **SEE FIXTURE CLARIFICATION NOTE #9 (NP) = NEW POLE (CBO) CONTROLLED BY OTHERS

SYMBOL QTY LABEL FIXTURE ARRANGEMENT TOTAL FIXTURE COUNT NEW POLE COUNT FIXTURE TYPE / MOUNTING / MANUFACTURER BUG RATING MOUNTING HEIGHT MOUNTING ACCESSORIES NOTES

8 C-DT1 SINGLE LR6X-7L-40K / CANOPY MOUNT / CREE MATCH EXISTING

1 C-SE1 SINGLE SEC-EDG-3M-WM-02-E-UL-BZ-350-40K / WALL MOUNT / CREE MATCH EXISTING

3 C-SH1 SINGLE SEC-EDG-4M-WM-02-E-UL-BZ-350-40K / WALL MOUNT / CREE MATCH EXISTING

1 C-SK1 SINGLE SEC-EDG-4M-WM-04-E-UL-BZ-525-40K / WALL MOUNT / CREE MATCH EXISTING

1 UU1 SINGLE RSXF2-LED-P6-40K-AWFD-MVOLT-AAWSC-DDBXD / FLOOD MOUNT / LITHONIA MATCH EXISTING

2 UU2 SINGLE RSXF1-LED-P3-40K-AWFD-MVOLT-AAWSC-DDBXD / FLOOD MOUNT / LITHONIA MATCH EXISTING

1 UU3 SINGLE RSXF1-LED-P3-40K-WFLD-MVOLT-AAWSC-DDBXD / FLOOD MOUNT / LITHONIA 9' - 6'' AFG

1 UU4 SINGLE RSXF1-LED-P3-40K-AWFD-MVOLT-AAWSC-DDBXD / FLOOD MOUNT / LITHONIA 13' - 6'' AFG

1 RI1 SINGLE EXISTING WALL FIXTURE -

1 YA1 SINGLE EXISTING POLE FIXTURE -

3 YD1 SINGLE EXISTING CANOPY FIXTURE -

6 YD2 SINGLE EXISTING CANOPY FIXTURE -

4 YF1 SINGLE EXISTING CANOPY FIXTURE -

1 YF2 SINGLE EXISTING CANOPY FIXTURE -

4 YI1 SINGLE EXISTING WALL FIXTURE -

** CONTRACTOR TO VERIFY MOUNTING ACCESSORIES BEFORE ORDERING**

8

1

3

1

1

2

1

1

1

1

3

6

4

1

4

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

B1-U0-G0

-

-

-

-

B1-U0-G1

B1-U0-G1

B2-U0-G2

B4-U0-G3

B3-U0-G2

B3-U0-G3

B3-U0-G2

-

GR8 TRIM RING

-

-

-

-

-

-

-

-

-

-

-

-

-

-

REPLACE EXISTING FIXTURE






ADD NEW FIXTURE

ADD NEW FIXTURE

REMOVE AND PATCH

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

-

-

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

33 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


LU-3

OVERALL SITE PLAN

BLUEGREEN

ORANGE


PL = PROPERTY LINE BASED ON COUNTY APPRAISAL INFORMATION

PINK = REPLACE WITH NEW POLE AT NEW HEIGHT= INDICATES NEW SECURITY FENCE

N.T.S.

FARGOWELLS

SCOPE OF PROJECT

REMAINDER OF PROPERTY

IS OUT OF SCOPE

KA

TO

NA

H A

VE

.

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

PLPL

PL

PL

PL

PLPL

PL

PL

PL

PL

PL

PL

PL

PLPLPLPLPL

PLPL

PLPL

PLPL

PLPL

PLPL

PLPL

PL PL PL PL PL PL PL PL

PLPL

PL

Katonah Office

262 Katonah Ave.

Katonah, NY

141510


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

v5 201203

N


QTY LABEL

8 C-DT1

1 C-SE1

3 C-SH1

1 C-SK1

1 UU1

2 UU2

1 UU3

1 UU4

1 RI1

1 YA1

3 YD1

6 YD2

4 YF1

1 YF2

4 YI1

NOTES







ADD NEW FIXTURE

ADD NEW FIXTURE

REMOVE AND PATCH

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

MOUNTING HEIGHT

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

9' - 6'' AFG

13' - 6'' AFG

-

-

-

-

-

-

-

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

33 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


LU-3a

SITE PLAN ENLARGEMENT

BLUEGREEN

ORANGE




FARGOWELLS

SCALE: 1 1/2" = 1'-0"

KA

TO

NA

H A

VE

.

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

C-DT1 C-SH1

YI1

YD1

YD1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

YI1

YI1

YI1

C-SK1

YA1

SEE SITE NOTE 1, 2, & 3

AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)

PL

PL

PL

PL

PLPLPL

YF1

YF1

UU1

UU2

UU2

UU4

UU3RI1

C-SH1

C-SH1

Katonah Office

262 Katonah Ave.

Katonah, NY

141510


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

v5 201203

N

1.2.3.

NEED STRUCTURAL ENGINEER TO COME UP WITH ACCEPTABLE MOUNTING BRACKET.BRACKET SHOULD BE ABLE TO HOLD FLOOD FIXTURES.FIXTURES WILL BE INSTALLED ON TOP OF BRACKET WITH A SLIPFITTER.

SITE NOTES:

EXISTING POLES - N/AEXISTING POLE BASES - N/AEXISTING DRIVE THRU CEILING - N/A

2.3.

1.

EXISTING CONDITIONS:


QTY LABEL

8 C-DT1

1 C-SE1

3 C-SH1

1 C-SK1

1 UU1

2 UU2

1 UU3

1 UU4

1 RI1

1 YA1

3 YD1

6 YD2

4 YF1

1 YF2

4 YI1

NOTES







ADD NEW FIXTURE

ADD NEW FIXTURE

REMOVE AND PATCH

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

MOUNTING HEIGHT

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

9' - 6'' AFG

13' - 6'' AFG

-

-

-

-

-

-

-

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

34 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


LU-4

FULL SITE

PHOTOMETRICS PLAN

N.T.S.

BLUEGREEN

ORANGE




FARGOWELLS

C-DT1 C-SH1

YI1

YD1

YD1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

YI1

YI1

YI1

C-SK1

YA1AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)

PL

PL

PL

PL

PLPLPL

YF1

YF1

UU1

UU2

UU2

UU4

UU3RI1

0.1 0.3 0.6 0.9 1.2 1.5 1.4 1.2 1.2 1.0 0.8 0.6 0.5 0.4 0.4

0.1 0.3 0.8 2.0 3.2 3.8 3.7 2.9 2.5 1.8 1.3 1.0 0.8 0.7 0.5

0.1 0.2 0.7 4.7 7.8 11.6 10.9 8.3 5.5 3.1 2.0 1.6 1.2 0.9 0.7

0.0 0.1 0.6 5.2 12.7 20.6 21.6 15.5 8.8 4.9 3.3 2.3 1.6 1.2 0.9

11.2 14.1 12.4 7.1 4.3 2.8 2.0 1.4 1.0

16.0 15.0 14.1 13.9 8.0 4.8 3.1 2.1 1.5 1.1

15.3 17.7 13.1 13.9 8.0 4.9 3.2 2.2 1.5 1.1

14.7 14.3 12.7 7.3 4.6 3.0 2.1 1.5 1.1

5.9 6.4 14.2 10.0 5.6 3.7 2.6 1.8 1.3 1.0

3.7 6.6 8.2 8.3 6.2 3.8 2.6 1.9 1.4 1.1 0.8

6.5 7.8 7.8 4.5 3.3 2.4 1.8 1.3 1.0 0.8 0.7

3.8 5.7 5.9 3.3 2.2 1.6 1.2 0.9 0.7 0.6 0.5

2.2 2.2 1.9 1.4 1.1 0.8 0.6 0.5 0.4 0.4

0.5 0.6 0.7 0.6 0.6 0.6 0.5 0.4 0.4 0.3 0.3

0.2 0.2 0.3 0.2 0.3 0.3 0.3 0.2 0.2 0.2

C-SH1

C-SH1


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

FULL SITE CALCS

Label CalcType Units Avg Max Min Avg/Min Max/Min

FULL SITE @ GRADE Illuminance Fc 3.81 21.6 0.0 N.A. N.A.

v5 201203

NOTES:

1. THE SCOPE OF WORK FOR THIS PROJECT IS LIMITED TOEXTERIOR LIGHTING RENOVATIONS AS SHOWN ON THE PLANS.

2. REFERENCE THE LUMINAIRE SCHEDULE (SHEET LU-2) FORADDITIONAL LIGHT FIXTURE INFORMATION.

N

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

34 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


LU-5

FIXTURE REMOVAL &

DIMENSIONING PLAN

BLUEGREEN

ORANGE




FARGOWELLS

SCALE: 1 1/2" = 1'-0"

KA

TO

NA

H A

VE

.

C-DT1 C-SH1

YI1

YD1

YD1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

YI1

YI1

YI1

C-SK1

YA1

SEE SITE NOTE 1, 2, & 3

AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)

PL

PL

PL

PL

PLPLPL

YF1

YF1

2'±

UU1

UU2

UU2

UU4

UU3RI1

C-SH1

C-SH1

1'-6"±


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

v5 201203

N

1.2.3.

NEED STRUCTURAL ENGINEER TO COME UP WITH ACCEPTABLE MOUNTING BRACKET.BRACKET SHOULD BE ABLE TO HOLD FLOOD FIXTURES.FIXTURES WILL BE INSTALLED ON TOP OF BRACKET WITH A SLIPFITTER.

SITE NOTES:

EXISTING POLES - N/AEXISTING POLE BASES - N/AEXISTING DRIVE THRU CEILING - N/A

2.3.

1.

EXISTING CONDITIONS:


QTY LABEL

8 C-DT1

1 C-SE1

3 C-SH1

1 C-SK1

1 UU1

2 UU2

1 UU3

1 UU4

1 RI1

1 YA1

3 YD1

6 YD2

4 YF1

1 YF2

4 YI1

NOTES







ADD NEW FIXTURE

ADD NEW FIXTURE

REMOVE AND PATCH

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

OUT OF SCOPE

MOUNTING HEIGHT

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

MATCH EXISTING

9' - 6'' AFG

13' - 6'' AFG

-

-

-

-

-

-

-

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

35 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


LU-6

ATM COMPLIANCE

AREA PHOTOMETRICS PLAN

N.T.S.

30' @ GRADE5' @ 60'' Horizontal

60' @ 60'' Vertical50' @ 60'' Horizontal

NOTES:

1. READINGS ARE MEASURED AS NOTED.

BLUEGREEN

ORANGE




FARGOWELLS


1

2

3

REVISEDBY

REVISED XX KRM

Katonah Office

SHEET NO.

DESIGN BY:

REVIEWED BY:

DRAWN BY:

APPROVED BY:KRM

DMWBRW

JTW

Katonah Office

262 Katonah Ave.

Katonah, NY

141510

v5 201203

N

C-DT1 C-SH1

YI1

YD1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

YI1

C-SK1

YA1AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)

PL

PL

PL

PLPLPL

COMPLIANCE AREA50' RADIUS

YF1

UU1

UU2

UU2

UU4

UU3RI1

3.7

8.2 7.2 5.8 4.0 3.0 2.3

20.6 16.5 11.7 6.7 4.8 3.4 2.6

6.9 4.6 3.5

8.7 6.1 4.7 3.8

11.1 8.1 6.2 4.8

10.0 7.4 5.5 4.2

3.1 2.7 2.3 2.1

4.4

8.4

60.9 47.5 28.0 17.6 10.6

39.9 36.5 14.6

15.7 32.2 31.7 16.4

17.6 14.4 16.7 16.5 13.2

15.0 14.3 16.6 18.5 14.5 10.6 7.6 5.7 4.3

21.6 3.1 26.6 19.8 21.9 15.2 10.5 7.6 5.7 4.4

18.1 8.4 26.1 19.7 21.4 15.0 10.4 7.6 5.7 4.5

24.8 16.9 16.3 17.3 14.0 10.3 7.6 5.7 4.4

24.1 14.2 15.8 15.3 12.5 9.4 7.0 5.4 4.2

8.6 30.2 30.3 16.0 10.0 7.4 5.8 4.6

3.1 39.3 38.9 15.2 8.3 5.6 4.4 3.6

11.1 14.4 21.2 18.8 11.7 7.0 4.7 3.4

6.1 6.2 6.0 7.4 6.3 5.0 3.8

10.2 7.4 5.2 4.6 3.9 3.2

16.2 9.0 5.6 3.9 3.1

17.4 9.2 5.5

C-SH1

C-SH1

UNIT CALCS 0'-5' (5FC MIN) @ 5' HORIZ


AHD 5' @ 60'' H Illuminance Fc 29.28 37.1 20.6 1.42 1.80

ATM 5' @ 60'' H Illuminance Fc 26.99 36.0 14.8 1.82 2.43

LOBBY 5' @ 60'' H Illuminance Fc 17.36 31.4 5.5 3.16 5.71

C-DT1 C-SH1YF2

YD2

AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)10' RADIUS

UU1

20.6

32.0 23.5

33.6 28.9

37.1

27.7 34.9 36.0

21.4 27.2 26.9 14.8

20.4

11.0 10.5

15.4 11.0 5.5 23.9

25.6 16.3 5.8 25.8

25.5 17.9 7.7 11.8

13.9 18.4 12.6 28.4

21.2 21.9

31.4

C-SH1

C-SH1

5' RADIUS

UNIT CALCS 30' (2FC MIN) @ GRADE



C-DT1 C-SH1

YI1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

C-SK1

AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)30' RADIUS

UU1

UU2

UU2

UU3RI125.9 22.9

21.8 14.3

11.3 16.4 13.3 15.7

12.1 14.6 14.0 15.5

15.5 13.9 14.4 15.8 14.2

12.5 14.0 15.8 13.8 16.7 14.5

11.3 8.7 14.8 12.9 16.5 14.6

18.0 15.1 13.9 15.3 14.1

16.5 15.7 14.6 15.1

12.4 17.0 14.1 15.8

4.5 17.6 14.5

5.8 5.5

C-SH1

C-SH1

C-DT1 C-SH1

YI1

YD1

YD1

C-DT1C-DT1

C-SE1

YF2

YD2

YI1

C-SK1

YA1AHD (1B)

LOBBY ENTRY (1B)

ATM (3A)

PL

PL

PL

PLPLPLPL

60' RADIUSYF1

YF1

UU1

UU2

UU2

UU4

UU3RI1

21.6 20.1 17.6 15.4 13.1 11.3 9.8 8.6

34.0 28.7 25.0 21.2 17.7 14.6 12.1 10.4 9.4

21.5 16.9 14.1 12.3 11.2 10.2

23.1 19.1 16.6 14.8 13.2 11.8

24.9 22.0 19.2 17.0 15.0 13.2

24.1 21.3 18.6 16.2 14.3 12.7

13.9 14.0 12.8 11.5 11.2 9.9 8.5 7.5

17.5

25.7

41.9 37.6 30.3

33.0

27.8

25.1 22.8 20.2 17.8 15.8 13.9

23.6 22.0 20.2 18.3 16.4 14.5

23.4 21.8 20.2 18.4 16.6 14.6

24.7 22.7 20.4 18.2 16.3 14.4

26.8 25.5 22.8 20.1 17.7 15.7 13.9

25.9 23.6 21.1 18.8 16.6 14.7

32.0 24.8 21.1 18.7 16.8 15.1 13.6

33.0 40.9 32.5 24.2 19.5 16.4 14.6 13.2 12.0

6.6 8.3 11.0 18.8 20.7 20.0 17.3 14.9 12.8 11.4

2.7 3.0 3.9 9.0 11.9 13.0 13.2 12.4 11.0

2.1 2.3 3.8 6.3 8.5 9.2 9.4 9.4 9.0

4.9 5.6 6.1 6.5 7.4 7.6 7.5

12.0 9.7 8.3 7.3 6.9 6.7

10.1 9.8 8.6

C-SH1

C-SH1

UNIT CALCS 50' @ 60'' HORZ



UNIT CALCS 60' (1FC MIN) @ 5' VERT


LOBBY 60' @ 60'' V Illuminance Fc 16.19 41.9 2.1 7.71 19.95

\\SB

SERV

ER\g

mrf

iles\

Wel

ls Fa

rgo\

2019

\Des

ign\

Ligh

ting

Prog

ram

\NY\

Kato

nah

(141

510)

- 26

2 Ka

tona

h Av

e\Ac

tive\

CAD

- 141

510

- V5

- 201

203

- DM

W.d

wg,

12/

4/20

20 2

:52:

36 P

M, A

utoC

AD P

DF (G

ener

al D

ocum

enta

tion)

.pc3

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text


© GMR 2019

Wells Fargo– 141510– 262 Katonah Ave, Katonah, NY

Add one UU1 flood fixture in place of the existing. Fixture finish is specified as bronze.

© GMR 2019


Add one UU4 flood fixture. Fixture finish is specified as bronze.

© GMR 2019


Replace 8 existing canopy with 8 C-DT1.

Replace existing can fixtures

© GMR 2019


Add 1 UU3 flood fixture. Fixture finish is specified as bronze.

© GMR 2019


Replace existing fixture with 1 C-SH1. Fixture finish is specified as bronze.

© GMR 2019


Replace 2 existing fixtures with 2 C-SH1. Fixture finish is specified as bronze.

© GMR 2019


Replace 1 existing fixtures with the C-SE1. Fixture finish is specified as bronze.

© GMR 2019


Replace 2 existing fixtures with 2 UU2 flood fixtures. Fixture finish is specified as bronze.

© GMR 2019


Replace 1 existing fixtures with 1 C-SK1. Fixture finish is specified as bronze.

© GMR 2019


Remove existing R1 Fixture.

© GMR 2019


All Y fixtures are left out of scope

Lithonia RSXF2 Flood LEDRev. 11/30/20

Page 1 of 8

One Lithonia Way • Conyers, Georgia 30012 • Phone: 800-705-SERV (7378) • www.acuitybrands.com© 2011-2020 Acuity Brands Lighting, Inc. All rights reserved.

COMMERCIAL OUTDOOR

Options Finish

Shipped InstalledPE Photocontrol, button style 6,7

PEX Photocontrol external threaded, adjustable 7,8

PER7 Seven-wire twist-lock receptacle only (no controls) 9,10,11

CE34 Conduit entry 3/4” NPT (Qty 2)SF Single fuse (120, 277, 347) 3

DF Double fuse (208, 240, 480) 3

SPD20KV 20KV Surge pack (10KV standard)FAO Field adjustable output 7,11

DMG 0-10V dimming extend out back of housing for external control (control ordered separate)7,11

DS Dual Switching 7,11,12

Shipped Installed*Standalone and Networked Sensors/Controls (factory default settings, see table page 9)NLTAIR2 nLight AIR generation 2 11,13,14

PIRHN Networked, Bi-Level motion/ambient sensor (for use with NLTAIR2) 11,14,15

Shipped Separately (requires some field assembly)FV Full Visor (360° around light aperture) 16

UBV Upper/bottom visor 16

BS Bird Spikes 17

*Note: PIRHN with nLight Air can be used as a standalone or networked solution. Sensor coverage pattern is affected when luminaire is tilted.

DDBXD Dark BronzeDBLXD BlackDNAXD Natural AluminumDWHXD WhiteDDBTXD Textured Dark BronzeDBLBXD Textured BlackDNATXD Textured Natural AluminumDWHGXD Textured White

WW

RSXF2 LED

Series Performance Package Color Temperature Distribution Voltage Mounting

RSXF2 LED P1P2P3P4P5P6

30K 3000K40K 4000K50K 5000K

AWFD Area Wide ForwardWFL Wide FloodMFL Medium FloodNFL Narrow FloodSP SpotNSP Narrow Spot

MVOLT (120V-277V) 1

HVOLT (347V-480V) 2

XVOLT (277V-480V) 4

(use specific voltage for options as noted)120 3 277 3

208 3 347 3

240 3 480 3

IS Adjustable slipfitter (fits 2-3/8” OD tenon) 5

YKC63 Yoke with 16-3 SO cord, 3ft 5

AASP Adjustable tilt arm square pole mounting 5

AARP Adjustable tilt arm round pole mounting 5

AAWB Adjustable tilt arm with wall bracket 5

AAWSC Adjustable tilt arm wall bracket and surface conduit box 5

Catalog Number

Notes

Type

Hit the Tab key or mouse over the page to see all interactive elements.

RSXF2 LEDFloodlight

Specifications

IntroductionThe new RSXF LED Flood family delivers maximum value by providing significant energy savings, long life and outstanding photometric performance at an affordable price. The RSXF2 delivers 11,000 to 31,000 lumens allowing it to replace 250W to 1000W HID floodlights.

The RSXF features an adjustable integral slipfitter that allows the luminaire to be mounted on a 2-3/8” OD tenon. Integral cover/wire box serves as an approved splice compartment allowing for fast, easy mounting and wiring without opening the electrical compartment. A yoke and other mounting configurations are available.

EPA (ft2@45°):

0.9 ft2 (0.08 m2)

Length: 28.3" (71.9 cm)

Width: 13.4” (34.0 cm)

Height: 3.0" (7.6 cm) Main Body7.6” (19.3 cm ) Arm

Weight (max):

39 lbs (17.7 kg)

Ordering Information EXAMPLE: RSXF2 LED P4 40K WFL MVOLT IS DDBXD

L

W

H

smpatterson

Text Box

RSXF2-LED-P6-40K-AWFD-MVOLT-AAWSC-DDBXD

smpatterson

Text Box

UU1

smpatterson

Text Box

GC TO SEE NOTES BELOW

smpatterson

Text Box

CONTRACTOR TO VERIFY THAT FIXTURES CAN BE MOUNTED PER PLAN AND ALL NECESSARY HARDWARE IS SPECIFIED FOR INSTALLATION PRIOR TO PURCHASING


Page 2 of 8


COMMERCIAL OUTDOOR

Ordering Information

NOTES1 MVOLT driver operates on any line voltage from 120-277V (50/60 Hz).2 HVOLT driver operates on any line voltage from 347-480V (50/60 Hz).3 Single fuse (SF) requires 120V, 277V or 347V. Double fuse (DF)

requires 208V, 240V or 480V.4 XVOLT driver not available with P1. XVOLT driver operates on any

line voltage from 277V-480V (50/60 Hz). XVOLT not available with fusing (SF or DF) and not available with PE or PEX.

5 Maximum tilt is 90° above horizontal.6 Requires MVOLT or 347V.7 Not available in combination with other light sensing control options

(following options cannot be combined: PE, PEX, PER7, FAO, DMG, PIRHN).

8 Requires 120V, 208V, 240V, 277V or 347V.9 Twistlock photocell ordered and shipped as a separate line item from

Acuity Brands Controls. See accessories. Shorting Cap included. Dimming leads capped for future use.

10 For units with option PER7, the mounting must be restricted to +/- 45° from horizontal aim per ANSI C136.10-2010.

11 Two or more of the following options cannot be combined including DMG, DS, PER7, FAO and PIRHN.

12 DS only available on performance package P4, P5 and P6.13 Must be ordered with PIRHN.14 Requires MVOLT or HVOLT.15 Must be ordered with NLTAIR2. For additional information on PIRHN

visit here.16 It may be ordered as an accessory.17 Must be ordered with fixture for factory pre-drilling.18 Requires luminaire to be specified with PER7 option. Ordered and

shipped as a separate line item from Acuity Brands Controls.

AccessoriesOrdered and shipped separately.

RSXF2FV (FINISH) U Full visor (specify finish)RSXF2UBV (FINISH) U Upper/bottom visor (specify finish)

DLL127F 1.5 JU Photocell - SSL twist-lock (120-277V) 18

DLL347F 1.5 CUL JU Photocell - SSL twist-lock (347V) 18

DLL480F 1.5 CUL JU Photocell -SSL twist-lock (480V) 18

DSHORT SBK U Shorting cap 18

UBV Visor - Top Mounted UBV Visor - Bottom Mounted Full Visor - 360°

External Shields

Pole/Mounting Informatiion

Accessories including bullhorns, cross arms and other adpaters are available under the accessories tab at Lithonia’s Outdoor Poles and Arms product page.Click here to visit Accessories.

RSXF2 - Luminaire EPA

EPA (ft2)

Fixture Quantity & Mounting Configuration Single 2 @ 90 2 @ 180 3 @ 90 3 @ 120 4 @ 90 2 Side

by Side3 Side

by Side4 Side

by Side

Mounting Type Tilt

IS - Integral SlipfitterYK - YokeAASP/AARP - Adjustable Arm Square/Round Pole

0 ° 0.69 1.22 1.27 1.8 1.61 2.39 1.37 2.06 2.7410° 0.53 1.06 1.05 1.58 1.37 2.08 1.06 1.59 2.1220° 0.52 1.02 1.03 1.52 1.33 2.02 1.03 1.55 2.0730° 0.64 1.11 1.18 1.63 1.45 2.21 1.27 1.91 2.5440° 0.81 1.21 1.35 1.74 1.65 2.39 1.62 2.43 3.2345° 0.91 1.25 1.5 1.81 1.75 2.48 1.82 2.73 3.6450° 1.34 1.83 2.17 2.61 2.56 3.62 2.68 4.02 5.3660° 2.2 2.97 3.57 4.24 4.17 5.89 4.41 6.61 8.8270° 2.86 4.13 4.7 5.89 5.71 8.21 5.71 8.57 11.4280° 3.4 5.13 5.67 7.34 7.09 10.21 6.79 10.19 13.5990° 3.85 5.96 6.55 8.58 8.31 11.88 7.7 11.56 15.41

*Includes luminaire and integral mounting arm. Other tenons, arms, brackets or other accessories are not included in this EPA data.

HANDHOLE ORIENTATION

AHandhole

B

C

D

RSXF ADJUSTABLE ARM

5.25”

2.65”

Top of Pole

0.563”

2.650”

1.325”0.400”(2 PLCS)

Template #8

RSX POLE DRILLING

Tenon O.D. RSX Mounting Single 2 @ 180 2 @ 90 3 @ 120 3 @ 90 4 @ 90

2 - 3/8" AARP AS3-5 190 AS3-5 280 AS3-5 290 AS3-5 320 AS3-5 390 AS3-5 490

2 - 7/8" AARP AST25-190 AST25-280 AST25-290 AST25-320 AST25-390 AST25-490

4" AARP AST35-190 AST35-280 AST35-290 AST35-320 AST35-390 AST35-490

Round Tenon Mount - Pole Top Slipfitters

Drilling Template Mounting Option Single 2 @ 180 2 @ 90 3 @ 120 3 @ 90 4 @ 90Head Location Side B Side B & D Side B & C Round Pole Only Side B, C & D Side A, B, C & D

#8 Drill Nomenclature DM19AS DM28AS DM29AS DM32AS DM39AS DM49AS

Drill Side Location by Configuration Type

https://www.acuitybrands.com/products/lighting/outdoor/poles-and-arms#c4fccc7e-7568-4942-aa27-0a1497c73bcf)


Page 3 of 8


COMMERCIAL OUTDOOR

To see complete photometric reports or download .ies files for this product, visit Lithonia Lighting’s RSX Area homepage. Photometric Diagrams

Isofootcandle plots for the RSXF2 LED P6 40K. Distances are in units of mounting height (30’).

LEGEND

0.1 fc

0.5 fc

1.0 fc

Luminaires tilted at 45˚

Visual - Template Tool

These lighting calculation results are for general informational purposes only and are provided without warranty as to accuracy, completeness, reliability or otherwise. Results are based on user provided data and data provided from publicly available sources; actual field conditions may affect calculated output. Visit www.Visual-3D.com .

Design Information Project Description

Thursday, August 02, 2018 Name Company Phone Email

[ A ] - RSXF2 LED P6 40K WFLManufacturer Acuity Brands Configuration Single

Lamp Lumens 29749 Orientation Single

Lamp Quantity 1 Mounting Height 30

Light Loss Factor 1 Arm Length 1

Input Power 246.6 Tilt 45

Max Illuminance 5 Area > 0.5fc 10000

Page 1 of 1Template Print

8/2/2018http://www.visual-3d.com/tools/template/Print.aspx?SessionID=2379267

WFLWFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ B ] - RSXF2 LED P6 40K MFLManufacturer Acuity Brands Configuration Single








MFLMFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ A ] - RSXF2 LED P6 40K AWFDManufacturer Acuity Brands Configuration Single








AWFDAWFD

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7






[ B ] - RSXF2 LED P6 40K NFLManufacturer Acuity Brands Configuration Single








NFLNFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ C ] - RSXF2 LED P6 40K SPManufacturer Acuity Brands Configuration Single








SPSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ D ] - RSXF2 LED P6 40K NSPManufacturer Acuity Brands Configuration Single








NSPNSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7


Page 4 of 8


COMMERCIAL OUTDOOR

Performance Data

Lumen Ambient Temperature(LAT) MultipliersUse these factors to determine relative lumen output for average ambient temperatures from 0-50°C (32-122°F).

Ambient Ambient Lumen Multiplier

0°C 32°F 1.05

5°C 41°F 1.04

10°C 50°F 1.03

15°C 59°F 1.02

20°C 68°F 1.01

25°C 77°F 1.00

30°C 86°F 0.99

35°C 95°F 0.98

40°C 104°F 0.97

45°C 113°F 0.9650°C 122°F 0.95

Current (A)

Performance Package System Watts (W) 120V 208V 240V 277V 347V 480VP1 71W 0.59 0.34 0.30 0.26 0.20 0.15P2 111W 0.93 0.53 0.46 0.40 0.32 0.23P3 147W 1.23 0.70 0.61 0.53 0.42 0.31P4 187W 1.55 0.90 0.78 0.68 0.53 0.38P5 210W 1.75 1.01 0.87 0.76 0.60 0.44P6 244W 2.03 1.17 1.01 0.88 0.70 0.51

Electrical Load

Values calculated according to IESNA TM-21-11 methodology and valid up to 40°C.

Operating Hours 50,000 75,000 100,000

Lumen Maintenance Factor >0.97 >0.95 >0.92

Projected LED Lumen Maintenance

Performance Package System Watts

Distribution.Type

Field Angle Beam Angle 30K (3000K, 70 CRI)

40K (4000K, 70 CRI)

50K (5000K, 70 CRI)

˚H ˚V ˚H ˚V Lumens LPW Max CD Lumens LPW Max CD Lumens LPW Max CD

P1 71W

AWFD 119 120 69 41 9,663 136 7,915 10,616 150 8,696 10,616 150 8,696WFL 133 129 116 80 9,467 133 4,031 10,401 146 4,428 10,401 146 4,428MFL 105 110 91 96 9,873 139 4,482 10,847 153 4,924 10,847 153 4,924NFL 78 79 44 45 9,529 134 14,090 10,469 147 15,480 10,469 147 15,480SP 48 48 27 27 9,223 130 29,378 10,133 143 32,277 10,133 143 32,277

NSP 42 44 19 21 9,385 132 49,553 10,311 145 54,443 10,311 145 54,443

P2 111W


NSP 42 44 19 21 14,660 132 77,406 16,107 145 85,046 16,107 145 85,046

P3 147W


NSP 42 44 19 21 18,461 126 97,475 20,282 138 107,090 20,282 138 107,090

P4 187W


NSP 42 44 19 21 22,314 119 117,820 24,516 131 129,446 24,516 131 129,446

P5 210W


NSP 42 44 19 21 24,012 114 126,785 26,381 126 139,294 26,381 126 139,294

P6 244W


NSP 42 44 19 21 26,842 110 141,728 29,491 121 155,715 29,491 121 155,715

Lumen OutputLumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown, within the tolerances allowed by Lighting Facts. Contact factory for performance data on any configurations not shown here.


Page 5 of 8


COMMERCIAL OUTDOOR

L

W H

Length: 28.3” (71.9 cm) Width: 13.4” (34.0 cm) Height: 3.0” (7.6 cm) Main Body

RSXF2 with Yoke (YKC63)

Yoke (YK) Mounting DetailNote: Mounting hole pattern is in-line with center of luminaire

5.90

.50 .63

1.522.52

.51

Length: 28.3” (71.9 cm)Width: 13.4” (34.0 cm)Height: 3.0” (7.6 cm) Main Body 7.6” (19.3 cm) Arm

RSXF2 with Adjustable Slipfitter (IS)

L

W H

7/8" KO - fits 1/2" NPT water- tight fitting

Dimensions


Page 6 of 8


COMMERCIAL OUTDOOR

Dimensions

L

W H

Length: 32.8” (83.3 cm) AASP 33.8” (85.9 cm) AARPWidth: 13.4” (34.0 cm)Height: 3.0” (7.6 cm) Main Body 7.2” (18.2 cm) Arm

RSXF2 with Adjustable Tilt Arm - Square or Round Pole (AASP or AARP)

NOTE:RPA - Round Pole mount can also be used to mount on square poles by omitting the round pole adapter plate shown here.


NotesAASP: Requires 3.0" min. square pole for 1 at 90°. Requires 3.5" min. square pole for mounting 2, 3, 4 at 90°.

AARP: Requires 3.2" min. dia. round pole for 2, 3, 4 at 90°. Requires 3.0" min. dia. round pole for mounting 1 at 90°, 2 at 180°, 3 at 120°.

L

W H


RSXF2 with Adjustable Tilt Arm with Wall Bracket (AAWB)

Wall Bracket (WBA) Mounting Detail

4.5

7.0



Page 7 of 8


COMMERCIAL OUTDOOR

Dimensions

L

W H


RSXF2 with Adjustable Tilt Arm with Wall Bracket and Surface Conduit Box (AAWSC)

Additional Reference Drawings

Surface Conduit Box (SCB) Mounting Detail4.4

7.0

3/4" NPT taps with plugs - Qty (4) provided


Option CE34 Reference Dimensions


Page 8 of 8


COMMERCIAL OUTDOOR

FEATURES & SPECIFICATIONS

INTENDED USE The RSX LED flood family is designed to provide a long-lasting, energy-efficient solution for the one-for-one replacement of existing metal halide or high pressure sodium lighting. The RSXF1 delivers 11,000 to 31,000 lumens and is ideal for replacing 250W to 1000W HID floodlights in parking lots and other area lighting applications.

CONSTRUCTION The RSX LED flood luminaire features a rugged die-cast aluminum main body that uses heat-dissipating fins and flow-through venting to provide optimal thermal management that both enhances LED performance and extends component life. Integral adjustable slipfitter mounts on a 2 3/8” OD tenon. The adjustable slipfitter has an integral junction box for easy installation. The light engines and housing are sealed against moisture and environmental contaminants to IP66. The low-profile design results in a low EPA, allowing pole optimization. Vibration rated per ANSI 136.31: RSXF and mountings rated for 3G vibration include IS, YK, AASP and AARP. RSXF and mountings rated for 1.5G vibration include AAWB and AAWSC.

FINISH Exterior parts are protected by a zinc-infused Super Durable TGIC thermoset powder coat finish that provides superior resistance to corrosion and weathering. A tightly controlled multi-stage process ensures superior adhesion as well as a minimum finish thickness of 3 mils. The result is a high-quality finish that is warrantied not to crack or peel.

OPTICS Precision acrylic refractive lenses are engineered for superior application efficiency, distributing the light to where it is needed most. Available in short and wide pattern distributions including Wide Flood, Medium Flood, Narrow Flood, Spot, Narrow Spot and an Area Wide/Forward distribution pattern featuring a strong forward throw reach that is ideal for lighting large areas from the perimeter..

ELECTRICAL Light engine(s) configurations consist of high-efficacy LEDs mounted on metal-core circuit boards and aluminum heat sinks to maximize heat dissipation. Light engines are IP66 rated. LED lumen maintenance is >L92/100,000 hours. CCT’s of 3000K, 4000K and 5000K (minimum 70 CRI) are available. Class 1 electronic drivers ensure system power factor >90% and THD <20%. Easily serviceable 10kV surge protection device meets a minimum Category C Low operation (per ANSI/IEEE C62.41.2).

STANDARD CONTROLS The RSX LED flood luminaire has a wide assortment of control options. Dusk to dawn controls include MVOLT and 347V button-type photocells and NEMA twist-lock photocell receptacles.

nLIGHT AIR CONTROLS The RSXF LED flood luminaire is also available with nLight® AIR which can be used for simple motion occupancy dimming or for the ultimate in wireless control. This powerful controls platform provides out-of-the-box basic motion sensing with photocontrol functionality and is suitable for mounting heights up to 40 feet. No commissioning is required when using factory default settings that provide basic stand-alone motion occupancy dimming that is switched on and off with a built-in photocell. See chart above for motion sensor default out-of-box settings. For more advanced wireless functionality, such as group dimming, nLight AIR can be commissioned using a smartphone and the easy-to-use CLAIRITY app. nLight AIR equipped luminaries can be grouped, resulting in motion sensor and photocell group response without the need for additional equipment. Scheduled dimming with motion sensor over-ride can be achieved when used with the nLight Eclypse. Additional information about nLight Air can be found here.

INSTALLATION The integral “IS” mount offers an adjustable slipfitter that mounts on a 2 3/8” OD tenon. The adjustable slipfitter has an integral junction box and offers easy installation, wiring and precision distribution pattern aiming. A steel yoke mount is also available and includes a water-tight cord grip and cord. Additional mountings are available including an adjustable tilt arm for direct-to-pole and wall and a surface conduit box for wall mount applications. All mountings are adjustable in 5° increments. RSXF is not rated for tilting above 90° or mounting within 4 feet of ground. Can be tilted up to 90° above horizontal.

LISTINGS CSA Certified to meet U.S. and Canadian standards. Suitable for wet locations. DesignLights Consortium® (DLC) Premium qualified product and DLC qualified product. Not all versions of this product may be DLC Premium qualified or DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.

WARRANTY 5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/support/customer-support/terms-and-conditions

Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.

PIRHN nLight Sensor Coverage PatternnLight PIRHN

TopSide

nLight Control - Sensor Coverage and Settings

Motion Sensor Default Settings - Option PIRHN

Option

Dimmed State (unoccupied)

High Level (when occupied)

Photocell Operation

Dwell Time (occupancy time delay)

Ramp-up Time (from unoccupied to occupied)

Ramp-down Time (from occupied to unoccupied)

PIRHN Approx. 30% Output 100% Output Enabled @ 1.5FC 7.5 minutes 3 seconds 5 minutes*Note: PIRHN default settings including photocell set-point, high/low dim rates, and occupancy sensor time delay are all configurable using the Clairity Pro App.

https://www.acuitybrands.com/products/controls/nlightair

http://www.acuitybrands.com/support/customer-support/terms-and-conditions

https://www.acuitybrands.com/products/detail/817178/nLight/rSDGR/-/media/products/nLight/817178/document/rSDGR_pdf.pdf


Lithonia RSXF1 Flood LED

Rev. 11/30/20Page 1 of 8

COMMERCIAL OUTDOOR

Catalog Number

Notes

Type


RSXF1 LEDFloodlight

Specifications



EPA (ft2@45°):

2.1 ft2 (0.2 m2)

Length: 20.7" (52.6 cm)

Width: 13.3” (33.8 cm)


Weight (max):

31 lbs (14.1 kg)

Options Finish

Shipped InstalledPE Photocontrol, button style 6, 8

PEX Photocontrol external threaded, adjustable 7, 8

PER7 Seven-wire twist-lock receptacle only (no controls) 8, 9, 10,11


DF Double fuse (208, 240, 480) 3

SPD20KV 20KV Surge pack (10KV standard)

FAO Field adjustable output 8,11

DMG 0-10V dimming extend out back of housing for external control (control ordered separate) 8,11

Shipped Separately (requires some field assembly)FV Full Visor (360° around light aperture)UBV Upper/bottom visorBS Bird Spikes 12


PIRHN Networked, Bi-Level motion/ambient sensor (for use with NLTAIR2) 8,11,13,15



WW


RSXF1 LED


RSXF1 LED P1P2P3P4

30K 3000K40K 4000K50K 5000K


MVOLT (120V-277V) 1

HVOLT (347V-480V) 2

XVOLT (277V-480V) 4


208 3 347 3

240 3 480 3







L

W

H

http://www.acuitybrands.com

smpatterson

Text Box

RSXF1-LED-P3-40K-AWFD-MVOLT-AAWSC-DDBXD

smpatterson

Text Box

UU2, 4

smpatterson

Text Box


smpatterson

Text Box




Rev. 11/30/20Page 2 of 8

COMMERCIAL OUTDOOR



RSXF1FV U Full visor (specify finish)RSXF1UBV U Upper/bottom visor (specify finish)RSXWBA U RSX WBA wall bracket (specify finish)

RSXSCB U RSX Surface conduit box (specify finish, for use with WBA, WBA not included)





NOTES1 MVOLT driver operates on any line voltage from 120-277V

(50/60 Hz).2 HVOLT driver operates on any line voltage from 347-480V

(50/60 Hz).3 Single fuse (SF) requires 120V, 277V or 347V. Double fuse

(DF) requires 208V, 240V or 480V.4 XVOLT driver not available with P1 or P2. XVOLT driver

operates on any line voltage from 277V-480V (50/60 Hz). XVOLT not available with fusing (SF or DF) and not available with PE or PEX.

5 Maximum tilt is 90° above horizontal.6 Requires MOVLT or 347V.7 Requires 120V, 208V, 240V, 277V or 347V.8 Not available in combination with other light sensing control

options (following options cannot be combined: PE, PEX,

PER7, FAO, DMG, PIRHN). 9 Twistlock photocell ordered and shipped as a separate line

item from Acuity Brands Controls. See accessories. Shorting Cap included. Dimming leads capped for future use.


11 Two or more of the following options cannot be combined including DMG, PER7, FAO and PIRHN.

12 Must be ordered with fixture for factory pre-drilling. 13 Must be ordered with PIRHN. 14 Requires MVOLT or HVOLT.15 Must be ordered with NLTAIR2. For additional information

on PIRHN visit here.16 Requires luminaire to be specified with PER7 option.

Ordered and shipped as a separate line item from Acuity Brands Controls.


External Shields




EPA (ft2)


by Side3 Side

by Side4 Side

by Side

Mounting Type Tilt


0 ° 0.57 1.03 1.05 1.52 1.36 2.03 1.31 1.7 2.2610° 0.68 1.34 1.33 2 1.74 2.64 1.35 2.03 2.7120° 0.87 1.71 1.73 2.56 2.26 3.42 1.75 2.62 3.4930° 1.24 2.19 2.3 3.21 2.87 4.36 2.49 3.73 4.9740° 1.81 2.68 2.98 3.85 3.68 5.3 3.62 5.43 7.2445° 2.11 2.92 3.44 4.2 4.08 5.77 4.22 6.33 8.4450° 2.31 3.17 3.72 4.52 4.44 6.26 4.62 6.94 9.2560° 2.71 3.66 4.38 5.21 5.15 7.24 5.43 8.14 10.8670° 2.78 3.98 4.54 5.67 5.47 7.91 5.52 8.27 11.0380° 2.76 4.18 4.62 5.97 5.76 8.31 5.51 8.27 11.0390° 2.73 4.25 4.64 6.11 5.91 8.47 5.45 8.18 10.97



AHandhole

B

C

D

RSXF ADJUSTABLE ARM

5.25”

2.65”

Top of Pole

0.563”

2.650”

1.325”0.400”(2 PLCS)

Template #8

RSX POLE DRILLING














Rev. 11/30/20Page 3 of 8

COMMERCIAL OUTDOOR



LEGEND

0.1 fc

0.5 fc

1.0 fc






[ C ] - RSXF1 LED P4 40K WFLManufacturer Acuity Brands Configuration Single








WFLWFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7













MFLMFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7













AWFDAWFD

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7






[ D ] - RSXF1 LED P4 40K NFLManufacturer Acuity Brands Configuration Single








NFLNFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ E1 ] - RSXF1 LED P4 40K SPManufacturer Acuity Brands Configuration Single








SPSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ E ] - RSXF1 LED P4 40K NSPManufacturer Acuity Brands Configuration Single








NSPNSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7




Rev. 11/30/20Page 4 of 8

COMMERCIAL OUTDOOR

Performance Data



0°C 32°F 1.05

5°C 41°F 1.04

10°C 50°F 1.03

15°C 59°F 1.02

20°C 68°F 1.01

25°C 77°F 1.00

30°C 86°F 0.99

35°C 95°F 0.98

40°C 104°F 0.97

45°C 113°F 0.96

50°C 122°F 0.95

Current (A)

Performance Package System Watts (W) 120V 208V 240V 277V 347V 480VP1 51W 0.42 0.25 0.21 0.19 0.14 0.11P2 72W 0.60 0.35 0.30 0.26 0.21 0.15P3 109W 0.91 0.52 0.45 0.39 0.31 0.23P4 133W 1.11 0.64 0.55 0.48 0.38 0.27

Electrical Load


Operating Hours 50,000 75,000 100,000



Performance Package System Watts Distribution. TypeField Angle Beam Angle 30K

(3000K, 70 CRI)40K

(4000K, 70 CRI)50K

(5000K, 70 CRI)


P1 51W


NSP 42 44 19 21 6,469 127 34,157 7,107 139 37,525 7,107 139 37,525

P2 72W


NSP 42 44 19 21 8,969 125 47,357 9,854 137 52,030 9,854 137 52,030

P3 109W


NSP 42 44 19 21 12,771 117 67,432 14,031 129 74,085 14,031 129 74,085

P4 133W


NSP 42 44 19 21 14,839 112 78,351 16,304 123 86,086 16,304 123 86,086





Rev. 11/30/20Page 5 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W

H




L

W

H



Yoke (YK) Mounting Detail

2.51.26

.51 .63




Rev. 11/30/20Page 6 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W H







L

W H




4.5

7.0





Rev. 11/30/20Page 7 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W H





7.0







Rev. 11/30/20Page 8 of 8

COMMERCIAL OUTDOOR





OPTICS Precision acrylic refractive lenses are engineered for superior application efficiency, distributing the light to where it is needed most. Available in short and wide pattern distributions including Wide Flood, Medium Flood, Narrow Flood, Spot, Narrow Spot and an Area Wide/Forward distribution pattern featuring a strong forward throw reach that is ideal for lighting large areas from the perimeter.









TopSide



Option



Photocell Operation




PIRHN Approx. 30% Output 100% Output Enabled @ 1.5FC 7.5 minutes 3 seconds 5 minutes

*Note: PIRHN default settings including photocell set-point, high/low dim rates, and occupancy sensor time delay are all configurable using the Clairity Pro App.







Rev. 11/30/20Page 1 of 8

COMMERCIAL OUTDOOR

Catalog Number

Notes

Type


RSXF1 LEDFloodlight

Specifications



EPA (ft2@45°):

2.1 ft2 (0.2 m2)

Length: 20.7" (52.6 cm)

Width: 13.3” (33.8 cm)


Weight (max):

31 lbs (14.1 kg)

Options Finish

Shipped InstalledPE Photocontrol, button style 6, 8

PEX Photocontrol external threaded, adjustable 7, 8

PER7 Seven-wire twist-lock receptacle only (no controls) 8, 9, 10,11


DF Double fuse (208, 240, 480) 3

SPD20KV 20KV Surge pack (10KV standard)

FAO Field adjustable output 8,11

DMG 0-10V dimming extend out back of housing for external control (control ordered separate) 8,11

Shipped Separately (requires some field assembly)FV Full Visor (360° around light aperture)UBV Upper/bottom visorBS Bird Spikes 12


PIRHN Networked, Bi-Level motion/ambient sensor (for use with NLTAIR2) 8,11,13,15



WW


RSXF1 LED


RSXF1 LED P1P2P3P4

30K 3000K40K 4000K50K 5000K


MVOLT (120V-277V) 1

HVOLT (347V-480V) 2

XVOLT (277V-480V) 4


208 3 347 3

240 3 480 3







L

W

H


smpatterson

Text Box

RSXF1-LED-P3-40K-WFLD-MVOLT-AAWSC-DDBXD

smpatterson

Text Box

UU3

smpatterson

Text Box


smpatterson

Text Box




Rev. 11/30/20Page 2 of 8

COMMERCIAL OUTDOOR



RSXF1FV U Full visor (specify finish)RSXF1UBV U Upper/bottom visor (specify finish)RSXWBA U RSX WBA wall bracket (specify finish)

RSXSCB U RSX Surface conduit box (specify finish, for use with WBA, WBA not included)





NOTES1 MVOLT driver operates on any line voltage from 120-277V

(50/60 Hz).2 HVOLT driver operates on any line voltage from 347-480V

(50/60 Hz).3 Single fuse (SF) requires 120V, 277V or 347V. Double fuse

(DF) requires 208V, 240V or 480V.4 XVOLT driver not available with P1 or P2. XVOLT driver

operates on any line voltage from 277V-480V (50/60 Hz). XVOLT not available with fusing (SF or DF) and not available with PE or PEX.

5 Maximum tilt is 90° above horizontal.6 Requires MOVLT or 347V.7 Requires 120V, 208V, 240V, 277V or 347V.8 Not available in combination with other light sensing control

options (following options cannot be combined: PE, PEX,

PER7, FAO, DMG, PIRHN). 9 Twistlock photocell ordered and shipped as a separate line

item from Acuity Brands Controls. See accessories. Shorting Cap included. Dimming leads capped for future use.


11 Two or more of the following options cannot be combined including DMG, PER7, FAO and PIRHN.

12 Must be ordered with fixture for factory pre-drilling. 13 Must be ordered with PIRHN. 14 Requires MVOLT or HVOLT.15 Must be ordered with NLTAIR2. For additional information

on PIRHN visit here.16 Requires luminaire to be specified with PER7 option.

Ordered and shipped as a separate line item from Acuity Brands Controls.


External Shields




EPA (ft2)


by Side3 Side

by Side4 Side

by Side

Mounting Type Tilt


0 ° 0.57 1.03 1.05 1.52 1.36 2.03 1.31 1.7 2.2610° 0.68 1.34 1.33 2 1.74 2.64 1.35 2.03 2.7120° 0.87 1.71 1.73 2.56 2.26 3.42 1.75 2.62 3.4930° 1.24 2.19 2.3 3.21 2.87 4.36 2.49 3.73 4.9740° 1.81 2.68 2.98 3.85 3.68 5.3 3.62 5.43 7.2445° 2.11 2.92 3.44 4.2 4.08 5.77 4.22 6.33 8.4450° 2.31 3.17 3.72 4.52 4.44 6.26 4.62 6.94 9.2560° 2.71 3.66 4.38 5.21 5.15 7.24 5.43 8.14 10.8670° 2.78 3.98 4.54 5.67 5.47 7.91 5.52 8.27 11.0380° 2.76 4.18 4.62 5.97 5.76 8.31 5.51 8.27 11.0390° 2.73 4.25 4.64 6.11 5.91 8.47 5.45 8.18 10.97



AHandhole

B

C

D

RSXF ADJUSTABLE ARM

5.25”

2.65”

Top of Pole

0.563”

2.650”

1.325”0.400”(2 PLCS)

Template #8

RSX POLE DRILLING














Rev. 11/30/20Page 3 of 8

COMMERCIAL OUTDOOR



LEGEND

0.1 fc

0.5 fc

1.0 fc






[ C ] - RSXF1 LED P4 40K WFLManufacturer Acuity Brands Configuration Single








WFLWFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7













MFLMFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7













AWFDAWFD

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7






[ D ] - RSXF1 LED P4 40K NFLManufacturer Acuity Brands Configuration Single








NFLNFL

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ E1 ] - RSXF1 LED P4 40K SPManufacturer Acuity Brands Configuration Single








SPSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7





[ E ] - RSXF1 LED P4 40K NSPManufacturer Acuity Brands Configuration Single








NSPNSP

7

6

54

3

2

10

-1

-2

-3

-4

-5-6

-7

7 06 5 4 3 2 1 1 2 3 4 5 6 7




Rev. 11/30/20Page 4 of 8

COMMERCIAL OUTDOOR

Performance Data



0°C 32°F 1.05

5°C 41°F 1.04

10°C 50°F 1.03

15°C 59°F 1.02

20°C 68°F 1.01

25°C 77°F 1.00

30°C 86°F 0.99

35°C 95°F 0.98

40°C 104°F 0.97

45°C 113°F 0.96

50°C 122°F 0.95

Current (A)

Performance Package System Watts (W) 120V 208V 240V 277V 347V 480VP1 51W 0.42 0.25 0.21 0.19 0.14 0.11P2 72W 0.60 0.35 0.30 0.26 0.21 0.15P3 109W 0.91 0.52 0.45 0.39 0.31 0.23P4 133W 1.11 0.64 0.55 0.48 0.38 0.27

Electrical Load


Operating Hours 50,000 75,000 100,000



Performance Package System Watts Distribution. TypeField Angle Beam Angle 30K

(3000K, 70 CRI)40K

(4000K, 70 CRI)50K

(5000K, 70 CRI)


P1 51W


NSP 42 44 19 21 6,469 127 34,157 7,107 139 37,525 7,107 139 37,525

P2 72W


NSP 42 44 19 21 8,969 125 47,357 9,854 137 52,030 9,854 137 52,030

P3 109W


NSP 42 44 19 21 12,771 117 67,432 14,031 129 74,085 14,031 129 74,085

P4 133W


NSP 42 44 19 21 14,839 112 78,351 16,304 123 86,086 16,304 123 86,086





Rev. 11/30/20Page 5 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W

H




L

W

H



Yoke (YK) Mounting Detail

2.51.26

.51 .63




Rev. 11/30/20Page 6 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W H







L

W H




4.5

7.0





Rev. 11/30/20Page 7 of 8

COMMERCIAL OUTDOOR

Dimensions

L

W H





7.0







Rev. 11/30/20Page 8 of 8

COMMERCIAL OUTDOOR





OPTICS Precision acrylic refractive lenses are engineered for superior application efficiency, distributing the light to where it is needed most. Available in short and wide pattern distributions including Wide Flood, Medium Flood, Narrow Flood, Spot, Narrow Spot and an Area Wide/Forward distribution pattern featuring a strong forward throw reach that is ideal for lighting large areas from the perimeter.









TopSide



Option



Photocell Operation




PIRHN Approx. 30% Output 100% Output Enabled @ 1.5FC 7.5 minutes 3 seconds 5 minutes

*Note: PIRHN default settings including photocell set-point, high/low dim rates, and occupancy sensor time delay are all configurable using the Clairity Pro App.





SKM C65921022416400

Documents

Transcript of SKM C65921022416400