Size and Performance Glazing performance Grille...
Transcript of Size and Performance Glazing performance Grille...
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-1
Impervia® Casement Windows
Size and Performance
Glazing performance
Grille Profiles and Patterns
Size Tables
Design Data
Detailed Product Description
Cross Sections
The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are subject to change without notice. Consult your local Pella representative for up-to-date product information.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-2
Impervia® Casement Windows
Size and Performance Data
Block Frame
Integral Nailing Fin
Sizes
Standard Vent/Fixed l l
Standard Fixed Companion Sizes l l
Transom Sizes l l
Egress Sizes l l
Special Sizes l l
Performance 1
Meets or Exceeds AAMA / WDMA Ratings C-LC45 – C-LC50Hallmark Certified
C-LC45 – C-LC50Hallmark Certified
Air Infiltration (cfm / ft 2 of frame @ 1.57 psf wind pressure) 0.05 0.05
Water Resistance 7.5 psf 7.5 psf
Design Pressure 45 – 50 psf 45– 50 psf
Other Performance Criteria
Forced Entry Resistance Level (Minimum Security Grade) 2 40 40
Maximum Operating Force (lb) Initiate Motion / Maintain Motion 15 / 6 15 / 6
Sound Transmission Class and Outdoor-Indoor Transmission Class
Product Frame Size Tested 3
Glazing SystemSTC
RatingOITC
RatingOverall Glazing Thickness
Exterior Glass Thickness
Interior Glass Thickness
VENT
23-1/2" x 59-1/2" 11/16" 2.5mm 2.5mm 25 22
23-1/2" x 59-1/2" 11/16" 3mm 5mm 32 28
23-1/2" x 59-1/2" 11/16" 3mm 6mm Laminated 32 28
FIXED
47-1/2" x 59-1/2" 11/16" 3mm 3mm 27 23
47-1/2" x 59-1/2" 11/16" 3mm 5mm 31 26
47-1/2" x 59-1/2" 11/16" 3mm 6mm Laminated 32 27
47-1/2" x 59-1/2" 11/16" 4mm 7mm Laminated 33 29
(1) See Design Data pages in this section for specific product performance class and grade values.
(2) The higher the level, the greater the product’s ability to resist forced entry.
(3) ASTM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-3
Impervia® Casement Windows
Features and Options
Block Frame Integral Nailing Fin
Glazing
Glazing Type
Dual-pane Insulating Glass S S
Insulated Glass Options / Low-E Types
Clear Insulating Glass (no Low-E coating) S S
Advanced Low-E Insulating Glass O O
SunDefense™ Low-E Insulating Glass O O
AdvancedComfort Low-E Insulating Glass O O
NaturalSun Low-E Insulating Glass O O
Additional Glass Options
Annealed Glass S S
Tempered Glass O O
Noise reduction glass (3/5mm, 4/6mm combinations) O O
Noise Reduction laminated glass (non-impact) O O
Tinted glass (Bronze, Gray, Green) Advanced Low-E O O
Obscure Glass 1 O O
Gas Fill / High Altitude
Argon S S
High Altitude O O
High Altitude with argon O O
Exterior / Interior
Powder-Coat White S S
Powder-Coat Tan, Brown, Black, or Morning Sky Gray O O
Dual-color (All exterior colors available with White interior) O —
Hardware
Match interior finish S S
Satin Nickel, Bright Brass or Oil-Rubbed Bronze
O O
Sash Locks
SureLock® System S S
Unison Lock System 2 S S
Screens
Conventional Black Fiberglass O O
InView™ screen O O
Grilles
Grilles-Between-the-Glass
Traditional, Prairie, Top Row and Custom - Equally Divided O O
S = Standard; O = Optional; (—) = Not available
(1) Contact your local Pella sales representative for current offering.
(2) Unit size determines availability.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-4
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Vent N NC SC S CA11/16" Clear IG PEL-N-150-00573-00001 2.5 2.5 air 0.44 0.55 0.57 44
with grilles-between-the-glass PEL-N-150-00573-00002 0.44 0.50 0.52 4411/16" Clear IG PEL-N-150-00573-00003 3 3 air 0.44 0.55 0.57 44
with grilles-between-the-glass PEL-N-150-00573-00004 0.44 0.50 0.52 4411/16" Advanced Low-E IG PEL-N-150-00604-00001 2.5 2.5 argon 0.28 0.26 0.49 60 NC
with grilles-between-the-glass PEL-N-150-00604-00002 0.28 0.24 0.44 60 NC SC S11/16" Advanced Low-E IG PEL-N-150-00604-00003 3 3 argon 0.28 0.26 0.49 60 NC
with grilles-between-the-glass PEL-N-150-00604-00004 0.28 0.24 0.44 60 NC SC S11/16" SunDefense™ IG PEL-N-150-00618-00001 2.5 2.5 argon 0.28 0.20 0.45 60 NC SC S
with grilles-between-the-glass PEL-N-150-00618-00002 0.28 0.18 0.41 60 NC SC S11/16" SunDefense™ IG PEL-N-150-00618-00003 3 3 argon 0.28 0.20 0.45 60 NC SC S
with grilles-between-the-glass PEL-N-150-00618-00004 0.28 0.18 0.41 60 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00630-00001 2.5 2.5 argon 0.25 0.26 0.48 47 N NC
with grilles-between-the-glass PEL-N-150-00630-00002 0.25 0.24 0.43 47 N NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00630-00003 3 3 argon 0.25 0.26 0.48 47 N NC
with grilles-between-the-glass PEL-N-150-00630-00004 0.25 0.24 0.43 47 N NC SC S11/16" NaturalSun Low-E IG PEL-N-150-00592-00001 2.5 2.5 argon 0.29 0.49 0.55 59 N
with grilles-between-the-glass PEL-N-150-00592-00002 0.29 0.44 0.50 59 N11/16" NaturalSun Low-E IG PEL-N-150-00592-00003 3 3 argon 0.29 0.49 0.55 59 N
with grilles-between-the-glass PEL-N-150-00592-00004 0.29 0.44 0.50 59 N
Vent — with Foam Insulation11/16" Advanced Low-E IG PEL-N-150-00678-00001 2.5 2.5 argon 0.27 0.26 0.49 60 N NC
with grilles-between-the-glass PEL-N-150-00678-00002 0.27 0.24 0.44 60 N NC SC S11/16" Advanced Low-E IG PEL-N-150-00678-00003 3 3 argon 0.27 0.26 0.49 60 N NC
with grilles-between-the-glass PEL-N-150-00678-00004 0.27 0.24 0.44 60 N NC SC S11/16" SunDefense IG PEL-N-150-00692-00001 2.5 2.5 argon 0.27 0.20 0.45 61 N NC SC S
with grilles-between-the-glass PEL-N-150-00692-00002 0.27 0.18 0.41 61 N NC SC S11/16" SunDefense IG PEL-N-150-00692-00003 3 3 argon 0.27 0.20 0.45 61 N NC SC S
with grilles-between-the-glass PEL-N-150-00692-00004 0.27 0.18 0.41 61 N NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00704-00001 2.5 2.5 argon 0.24 0.26 0.48 47 N NC
with grilles-between-the-glass PEL-N-150-00704-00002 0.24 0.24 0.43 47 N NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00704-00003 3 3 argon 0.24 0.26 0.48 47 N NC
with grilles-between-the-glass PEL-N-150-00704-00004 0.24 0.24 0.43 47 N NC SC S11/16" NaturalSun Low-E IG PEL-N-150-00666-00001 2.5 2.5 argon 0.28 0.49 0.55 59 N
with grilles-between-the-glass PEL-N-150-00666-00002 0.28 0.44 0.50 59 N11/16" NaturalSun Low-E IG PEL-N-150-00666-00003 3 3 argon 0.28 0.49 0.55 59 N
with grilles-between-the-glass PEL-N-150-00666-00004 0.28 0.44 0.50 59 N
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-5
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Vent - High Altitude Glazing N NC SC S CA11/16" (HA) Advanced Low-E IG PEL-N-150-00597-00001 2.5 2.5 air 0.32 0.27 0.49 56
with grilles-between-the-glass PEL-N-150-00597-00002 0.32 0.25 0.44 56 S11/16" (HA) Advanced Low-E IG PEL-N-150-00597-00003 3 3 air 0.32 0.27 0.49 56
with grilles-between-the-glass PEL-N-150-00597-00004 0.32 0.25 0.44 56 S11/16" (HA) SunDefense IG PEL-N-150-00611-00001 2.5 2.5 air 0.31 0.20 0.45 57 S
with grilles-between-the-glass PEL-N-150-00611-00002 0.31 0.19 0.41 57 S11/16" (HA) SunDefense IG PEL-N-150-00611-00003 3 3 air 0.31 0.20 0.45 57 S
with grilles-between-the-glass PEL-N-150-00611-00004 0.31 0.19 0.41 57 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00625-00001 2.5 2.5 air 0.27 0.26 0.48 43 N NC
with grilles-between-the-glass PEL-N-150-00625-00002 0.27 0.24 0.43 43 N NC SC S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00625-00003 3 3 air 0.27 0.26 0.48 43 N NC
with grilles-between-the-glass PEL-N-150-00625-00004 0.27 0.24 0.43 43 N NC SC S11/16" (HA) NaturalSun Low-E IG PEL-N-150-00587-00001 2.5 2.5 air 0.32 0.48 0.55 56
with grilles-between-the-glass PEL-N-150-00587-00002 0.32 0.44 0.50 5611/16" (HA) NaturalSun Low-E IG PEL-N-150-00587-00003 3 3 air 0.32 0.48 0.55 56
with grilles-between-the-glass PEL-N-150-00587-00004 0.32 0.44 0.50 56
Vent - High Altitude Glazing — with Foam Insulation11/16" (HA) Advanced Low-E IG PEL-N-150-00671-00001 2.5 2.5 air 0.31 0.27 0.49 56
with grilles-between-the-glass PEL-N-150-00671-00002 0.31 0.25 0.44 56 S11/16" (HA) Advanced Low-E IG PEL-N-150-00671-00003 3 3 air 0.31 0.27 0.49 56
with grilles-between-the-glass PEL-N-150-00671-00004 0.31 0.25 0.44 56 S11/16" (HA) SunDefense IG PEL-N-150-00685-00001 2.5 2.5 air 0.30 0.20 0.45 57 NC SC S
with grilles-between-the-glass PEL-N-150-00685-00002 0.30 0.19 0.41 57 NC SC S11/16" (HA) SunDefense IG PEL-N-150-00685-00003 3 3 air 0.30 0.20 0.45 57 NC SC S
with grilles-between-the-glass PEL-N-150-00685-00004 0.30 0.19 0.41 57 NC SC S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00699-00001 2.5 2.5 air 0.26 0.26 0.48 43 N NC
with grilles-between-the-glass PEL-N-150-00699-00002 0.26 0.24 0.43 43 N NC SC S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00699-00003 3 3 air 0.26 0.26 0.48 43 N NC
with grilles-between-the-glass PEL-N-150-00699-00004 0.26 0.24 0.43 43 N NC SC S11/16" (HA) NaturalSun Low-E IG PEL-N-150-00661-00001 2.5 2.5 air 0.31 0.48 0.55 56
with grilles-between-the-glass PEL-N-150-00661-00002 0.31 0.44 0.50 5611/16" (HA) NaturalSun Low-E IG PEL-N-150-00661-00003 3 3 air 0.31 0.48 0.55 56
with grilles-between-the-glass PEL-N-150-00661-00004 0.31 0.44 0.50 56
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-6
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Vent - 3mm/5mm Glazing N NC SC S CA11/16" Clear IG PEL-N-150-00574-00001 3 5 air 0.45 0.54 0.57 42
with grilles-between-the-glass PEL-N-150-00577-00001 0.45 0.49 0.52 4211/16" Advanced Low-E IG PEL-N-150-00605-00001 3 5 argon 0.29 0.27 0.49 57 NC
with grilles-between-the-glass PEL-N-150-00608-00001 0.30 0.24 0.44 57 NC SC S11/16" SunDefense™ IG PEL-N-150-00619-00001 3 5 argon 0.29 0.20 0.45 57 NC SC S
with grilles-between-the-glass PEL-N-150-00622-00001 0.30 0.18 0.41 57 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00631-00001 3 5 argon 0.26 0.26 0.47 44 N NC
with grilles-between-the-glass PEL-N-150-00633-00001 0.26 0.24 0.43 44 N NC SC S11/16" NaturalSun Low-E IG PEL-N-150-00593-00001 3 5 argon 0.30 0.48 0.55 56 N
with grilles-between-the-glass PEL-N-150-00595-00001 0.31 0.44 0.50 56
Vent - 3mm/5mm Glazing — with Foam Insulation11/16" Advanced Low-E IG PEL-N-150-00679-00001 3 5 argon 0.28 0.27 0.49 57 NC
with grilles-between-the-glass PEL-N-150-00682-00001 0.29 0.24 0.44 57 NC SC S11/16" SunDefense IG PEL-N-150-00693-00001 3 5 argon 0.28 0.20 0.45 57 NC SC S
with grilles-between-the-glass PEL-N-150-00696-00001 0.29 0.18 0.41 57 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-150-00705-00001 3 5 argon 0.25 0.26 0.47 44 N NC SC
with grilles-between-the-glass PEL-N-150-00707-00001 0.25 0.24 0.43 44 N NC S11/16" NaturalSun Low-E IG PEL-N-150-00667-00001 3 5 argon 0.29 0.48 0.55 56 N
with grilles-between-the-glass PEL-N-150-00669-00001 0.30 0.44 0.50 56 NVent - 3mm/5mm High Altitude Glazing11/16" (HA) Advanced Low-E IG PEL-N-150-00598-00001 3 5 air 0.33 0.27 0.49 53
with grilles-between-the-glass PEL-N-150-00601-00001 0.34 0.25 0.44 53 S11/16" (HA) SunDefense IG PEL-N-150-00612-00001 3 5 air 0.33 0.20 0.45 53 S
with grilles-between-the-glass PEL-N-150-00615-00001 0.34 0.19 0.41 53 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00626-00001 3 5 air 0.28 0.26 0.47 41 NC
with grilles-between-the-glass PEL-N-150-00628-00001 0.29 0.24 0.43 41 NC SC S11/16" (HA) NaturalSun Low-E IG PEL-N-150-00588-00001 3 5 air 0.34 0.48 0.55 52
with grilles-between-the-glass PEL-N-150-00590-00001 0.35 0.44 0.50 52Vent - 3mm/5mm High Altitude Glazing — with Foam Insulation11/16" (HA) Advanced Low-E IG PEL-N-150-00672-00001 3 5 air 0.32 0.27 0.49 53
with grilles-between-the-glass PEL-N-150-00675-00001 0.33 0.25 0.44 53 S11/16" (HA) SunDefense IG PEL-N-150-00686-00001 3 5 air 0.32 0.20 0.45 53 S
with grilles-between-the-glass PEL-N-150-00689-00001 0.33 0.19 0.41 54 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-150-00700-00001 3 5 air 0.27 0.26 0.47 41 N NC
with grilles-between-the-glass PEL-N-150-00702-00001 0.28 0.24 0.43 41 NC SC S11/16" (HA) NaturalSun Low-E IG PEL-N-150-00662-00001 3 5 air 0.33 0.48 0.55 52
with grilles-between-the-glass PEL-N-150-00664-00001 0.34 0.44 0.50 52
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-7
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Vent – Tinted Glazing N NC SC S CA11/16" Bronze Advanced Low-E IG PEL-N-150-00641-00001 5 3 argon 0.29 0.23 0.32 58 NC SC S
with grilles-between-the-glass PEL-N-150-00642-00001 0.30 0.21 0.29 58 NC SC S11/16" Gray Advanced Low-E IG PEL-N-150-00643-00001 5 3 argon 0.29 0.22 0.27 58 NC SC S
with grilles-between-the-glass PEL-N-150-00644-00001 0.30 0.20 0.25 58 NC SC S11/16" Green Advanced Low-E IG PEL-N-150-00645-00001 5 3 argon 0.29 0.27 0.43 58 NC
with grilles-between-the-glass PEL-N-150-00646-00001 0.30 0.24 0.39 58 NC SC S
Vent — Tinted Glazing with Foam Insulation11/16" Bronze Advanced Low-E IG PEL-N-150-00715-00001 5 3 argon 0.27 0.27 0.36 58 N NC
with grilles-between-the-glass PEL-N-150-00716-00001 0.28 0.24 0.32 58 NC SC S11/16" Gray Advanced Low-E IG PEL-N-150-00717-00001 5 3 argon 0.27 0.25 0.31 58 N NC SC S
with grilles-between-the-glass PEL-N-150-00718-00001 0.28 0.22 0.28 58 NC SC S11/16" Green Advanced Low-E IG PEL-N-150-00719-00001 5 3 argon 0.27 0.30 0.49 58 N NC
with grilles-between-the-glass PEL-N-150-00720-00001 0.28 0.27 0.44 58 NCVent – High Altitude Glazing – with Tinted Glazing11/16" Bronze Advanced Low-E IG PEL-N-150-00635-00001 5 3 air 0.33 0.24 0.32 54 S
with grilles-between-the-glass PEL-N-150-00636-00001 0.34 0.22 0.29 54 S11/16" Gray Advanced Low-E IG PEL-N-150-00637-00001 5 3 air 0.33 0.22 0.27 54 S
with grilles-between-the-glass PEL-N-150-00638-00001 0.34 0.20 0.25 54 S11/16" Green Advanced Low-E IG PEL-N-150-00639-00001 5 3 air 0.33 0.27 0.43 54
with grilles-between-the-glass PEL-N-150-00640-00001 0.34 0.25 0.39 54 SVent – High Altitude Glazing — with Foam Insulation and Tinted Glazing11/16" Bronze Advanced Low-E IG PEL-N-150-00709-00001 5 3 air 0.32 0.24 0.32 55 S
with grilles-between-the-glass PEL-N-150-00710-00001 0.33 0.22 0.29 55 S11/16" Gray Advanced Low-E IG PEL-N-150-00711-00001 5 3 air 0.32 0.22 0.27 55 S
with grilles-between-the-glass PEL-N-150-00712-00001 0.33 0.20 0.25 55 S11/16" Green Advanced Low-E IG PEL-N-150-00713-00001 5 3 air 0.32 0.27 0.43 55
with grilles-between-the-glass PEL-N-150-00714-00001 0.33 0.25 0.39 55 S
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-8
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Vent — Laminated Glazing N NC SC S CA11/16" Advanced Low-E IG PEL-N-150-00606-00001 3 6 argon 0.31 0.26 0.48 56
with grilles-between-the-glass PEL-N-150-00609-00001 0.32 0.24 0.43 56 S11/16" SunDefense™ IG PEL-N-150-00620-00001 3 6 argon 0.30 0.20 0.44 56 NC SC S
with grilles-between-the-glass PEL-N-150-00623-00001 0.32 0.18 0.40 57 S
Vent — Laminated Glazing with Foam Insulation11/16" Advanced Low-E IG PEL-N-150-00680-00001 3 6 argon 0.30 0.26 0.48 56 NC
with grilles-between-the-glass PEL-N-150-00683-00001 0.31 0.24 0.43 56 S11/16" SunDefense™ IG PEL-N-150-00694-00001 3 6 argon 0.29 0.20 0.44 57 NC SC S
with grilles-between-the-glass PEL-N-150-00697-00001 0.31 0.18 0.40 57 SVent - High Altitude Laminated Glazing
11/16" Advanced Low-E IG PEL-N-150-00599-00001 3 6 air 0.35 0.27 0.48 52 with grilles-between-the-glass PEL-N-150-00602-00001 0.37 0.24 0.43 52 S
11/16" SunDefense IG PEL-N-150-00613-00001 3 6 air 0.35 0.20 0.44 52 S with grilles-between-the-glass PEL-N-150-00616-00001 0.36 0.19 0.40 52 S
Vent - High Altitude Laminated Glazing with Foam Insulation11/16" Advanced Low-E IG PEL-N-150-00673-00001 3 6 air 0.34 0.27 0.48 52
with grilles-between-the-glass PEL-N-150-00676-00001 0.36 0.24 0.43 52 S11/16" SunDefense IG PEL-N-150-00687-00001 3 6 air 0.34 0.20 0.44 52 S
with grilles-between-the-glass PEL-N-150-00690-00001 0.35 0.19 0.40 52 S
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-9
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Fixed N NC SC S CA11/16" Clear IG PEL-N-152-01133-00001 2.5 2.5 air 0.45 0.62 0.66 44
with grilles-between-the-glass PEL-N-152-01133-00002 0.45 0.56 0.59 4411/16" Clear IG PEL-N-152-01133-00003 3 3 air 0.45 0.62 0.66 44
with grilles-between-the-glass PEL-N-152-01133-00004 0.45 0.56 0.59 4411/16" Clear IG PEL-N-152-01138-00001 5 5 air 0.47 0.60 0.65 41
with grilles-between-the-glass PEL-N-152-01143-00001 0.48 0.53 0.58 4111/16" Advanced Low-E IG PEL-N-152-01180-00001 2.5 2.5 argon 0.27 0.30 0.56 59 N NC
with grilles-between-the-glass PEL-N-152-01180-00002 0.27 0.27 0.50 59 N NC11/16" Advanced Low-E IG PEL-N-152-01180-00003 3 3 argon 0.27 0.30 0.56 59 N NC
with grilles-between-the-glass PEL-N-152-01180-00004 0.27 0.27 0.50 59 N NC11/16" Advanced Low-E IG PEL-N-152-01185-00001 5 5 argon 0.30 0.30 0.55 55 NC
with grilles-between-the-glass PEL-N-152-01190-00001 0.32 0.27 0.49 5511/16" SunDefense™ IG PEL-N-152-01202-00001 2.5 2.5 argon 0.27 0.22 0.52 60 N NC SC S
with grilles-between-the-glass PEL-N-152-01202-00002 0.27 0.20 0.46 60 N NC SC S11/16" SunDefense™ IG PEL-N-152-01202-00003 3 3 argon 0.27 0.22 0.52 60 N NC SC S
with grilles-between-the-glass PEL-N-152-01202-00004 0.27 0.20 0.46 60 N NC SC S11/16" SunDefense™ IG PEL-N-152-01207-00001 5 5 argon 0.29 0.23 0.51 55 NC SC S
with grilles-between-the-glass PEL-N-152-01212-00001 0.31 0.21 0.46 55 S11/16" AdvancedComfort Low-E IG PEL-N-152-01220-00001 2.5 2.5 argon 0.23 0.30 0.55 47 N NC
with grilles-between-the-glass PEL-N-152-01220-00002 0.23 0.27 0.49 47 N NC11/16" AdvancedComfort Low-E IG PEL-N-152-01220-00003 3 3 argon 0.23 0.30 0.55 47 N NC
with grilles-between-the-glass PEL-N-152-01220-00004 0.23 0.27 0.49 47 N NC11/16" AdvancedComfort Low-E IG PEL-N-152-01223-00001 5 5 argon 0.26 0.29 0.54 42 N NC
with grilles-between-the-glass PEL-N-152-01226-00001 0.27 0.26 0.48 42 N NC11/16" NaturalSun Low-E IG PEL-N-152-01162-00001 2.5 2.5 argon 0.28 0.55 0.64 59 N 36 CA
with grilles-between-the-glass PEL-N-152-01162-00002 0.28 0.50 0.57 59 N11/16" NaturalSun Low-E IG PEL-N-152-01162-00003 3 3 argon 0.28 0.55 0.64 59 N 36 CA
with grilles-between-the-glass PEL-N-152-01162-00004 0.28 0.50 0.57 59 N11/16" NaturalSun Low-E IG PEL-N-152-01165-00001 5 5 argon 0.31 0.53 0.63 54
with grilles-between-the-glass PEL-N-152-01168-00001 0.32 0.48 0.56 54Fixed — with Foam Insulation11/16" Advanced Low-E IG PEL-N-152-01298-00001 2.5 2.5 argon 0.26 0.30 0.56 59 N NC
with grilles-between-the-glass PEL-N-152-01298-00002 0.26 0.27 0.50 59 N NC11/16" Advanced Low-E IG PEL-N-152-01298-00003 3 3 argon 0.26 0.30 0.56 59 N NC
with grilles-between-the-glass PEL-N-152-01298-00004 0.26 0.27 0.50 59 N NC11/16" Advanced Low-E IG PEL-N-152-01303-00001 5 5 argon 0.29 0.30 0.55 55 NC
with grilles-between-the-glass PEL-N-152-01308-00001 0.31 0.27 0.49 5511/16" SunDefense IG PEL-N-152-01320-00001 2.5 2.5 argon 0.26 0.22 0.52 60 N NC SC S
with grilles-between-the-glass PEL-N-152-01320-00002 0.26 0.20 0.46 60 N NC SC S11/16" SunDefense IG PEL-N-152-01320-00003 3 3 argon 0.26 0.22 0.52 60 N NC SC S
with grilles-between-the-glass PEL-N-152-01320-00004 0.26 0.20 0.46 60 N NC SC S11/16" SunDefense IG PEL-N-152-01325-00001 5 5 argon 0.29 0.23 0.51 55 NC SC S
with grilles-between-the-glass PEL-N-152-01330-00001 0.30 0.21 0.46 55 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-152-01338-00001 2.5 2.5 argon 0.22 0.30 0.55 47 N NC
with grilles-between-the-glass PEL-N-152-01338-00002 0.22 0.27 0.49 47 N NC11/16" AdvancedComfort Low-E IG PEL-N-152-01338-00003 3 3 argon 0.22 0.30 0.55 47 N NC
with grilles-between-the-glass PEL-N-152-01338-00004 0.22 0.27 0.49 47 N NC
11/16" AdvancedComfort Low-E IG PEL-N-152-01341-00001 5 5 argon 0.25 0.29 0.54 42 N NC with grilles-between-the-glass PEL-N-152-01344-00001 0.26 0.26 0.48 42 N NC
11/16" NaturalSun Low-E IG PEL-N-152-01280-00001 2.5 2.5 argon 0.27 0.55 0.64 59 N 37 CA with grilles-between-the-glass PEL-N-152-01280-00002 0.27 0.50 0.57 59 N 34 CA
11/16" NaturalSun Low-E IG PEL-N-152-01280-00003 3 3 argon 0.27 0.55 0.64 59 N 37 CA with grilles-between-the-glass PEL-N-152-01280-00004 0.27 0.50 0.57 59 N 34 CA
11/16" NaturalSun Low-E IG PEL-N-152-01283-00001 5 5 argon 0.30 0.53 0.63 54 N with grilles-between-the-glass PEL-N-152-01286-00001 0.32 0.48 0.56 54
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-10
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Fixed - High Altitude Glazing N NC SC S CA11/16" (HA) Advanced Low-E IG PEL-N-152-01169-00001 2.5 2.5 air 0.31 0.30 0.56 55
with grilles-between-the-glass PEL-N-152-01169-00002 0.31 0.28 0.50 5511/16" (HA) Advanced Low-E IG PEL-N-152-01169-00003 3 3 air 0.31 0.30 0.56 55
with grilles-between-the-glass PEL-N-152-01169-00004 0.31 0.28 0.50 5511/16" (HA) Advanced Low-E IG PEL-N-152-01174-00001 5 5 air 0.35 0.30 0.55 50
with grilles-between-the-glass PEL-N-152-01179-00001 0.37 0.27 0.49 5011/16" (HA) SunDefense IG PEL-N-152-01191-00001 2.5 2.5 air 0.31 0.23 0.52 56 S
with grilles-between-the-glass PEL-N-152-01191-00002 0.31 0.21 0.46 56 S11/16" (HA) SunDefense IG PEL-N-152-01191-00003 3 3 air 0.31 0.23 0.52 56 S
with grilles-between-the-glass PEL-N-152-01191-00004 0.31 0.21 0.46 56 S11/16" (HA) SunDefense IG PEL-N-152-01196-00001 5 5 air 0.35 0.23 0.51 51 S
with grilles-between-the-glass PEL-N-152-01201-00001 0.36 0.21 0.46 51 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01213-00001 2.5 2.5 air 0.26 0.30 0.55 43 N NC
with grilles-between-the-glass PEL-N-152-01213-00002 0.26 0.27 0.49 43 N NC11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01213-00003 3 3 air 0.26 0.30 0.55 43 N NC
with grilles-between-the-glass PEL-N-152-01213-00004 0.26 0.27 0.49 43 N NC11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01216-00001 5 5 air 0.29 0.29 0.54 38 NC
with grilles-between-the-glass PEL-N-152-01219-00001 0.30 0.26 0.48 38 NC11/16" (HA) NaturalSun Low-E IG PEL-N-152-01155-00001 2.5 2.5 air 0.32 0.55 0.64 55
with grilles-between-the-glass PEL-N-152-01155-00002 0.32 0.50 0.57 5511/16" (HA) NaturalSun Low-E IG PEL-N-152-01155-00003 3 3 air 0.32 0.55 0.64 55
with grilles-between-the-glass PEL-N-152-01155-00004 0.32 0.50 0.57 5511/16" (HA) NaturalSun Low-E IG PEL-N-152-01158-00001 5 5 air 0.36 0.53 0.63 50
with grilles-between-the-glass PEL-N-152-01161-00001 0.38 0.48 0.56 50
Fixed - High Altitude Glazing with Foam Insulation11/16" (HA) Advanced Low-E IG PEL-N-152-01287-00001 2.5 2.5 air 0.30 0.30 0.56 56 NC
with grilles-between-the-glass PEL-N-152-01287-00002 0.30 0.28 0.50 56 NC11/16" (HA) Advanced Low-E IG PEL-N-152-01287-00003 3 3 air 0.30 0.30 0.56 56 NC
with grilles-between-the-glass PEL-N-152-01287-00004 0.30 0.28 0.50 56 NC11/16" (HA) Advanced Low-E IG PEL-N-152-01292-00001 5 5 air 0.34 0.30 0.55 50
with grilles-between-the-glass PEL-N-152-01297-00001 0.36 0.27 0.49 5011/16" (HA) SunDefense IG PEL-N-152-01309-00001 2.5 2.5 air 0.30 0.23 0.52 56 NC SC S
with grilles-between-the-glass PEL-N-152-01309-00002 0.30 0.21 0.46 56 NC SC S11/16" (HA) SunDefense IG PEL-N-152-01309-00003 3 3 air 0.30 0.23 0.52 56 NC SC S
with grilles-between-the-glass PEL-N-152-01309-00004 0.30 0.21 0.46 56 NC SC S11/16" (HA) SunDefense IG PEL-N-152-01314-00001 5 5 air 0.34 0.23 0.51 51 S
with grilles-between-the-glass PEL-N-152-01319-00001 0.36 0.21 0.46 51 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01331-00001 2.5 2.5 air 0.25 0.30 0.55 43 N NC
with grilles-between-the-glass PEL-N-152-01331-00002 0.25 0.27 0.49 43 N NC11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01331-00003 3 3 air 0.25 0.30 0.55 43 N NC
with grilles-between-the-glass PEL-N-152-01331-00004 0.25 0.27 0.49 43 N NC11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01334-00001 5 5 air 0.28 0.29 0.54 38 NC
with grilles-between-the-glass PEL-N-152-01337-00001 0.30 0.26 0.48 38 NC11/16" (HA) NaturalSun Low-E IG PEL-N-152-01273-00001 2.5 2.5 air 0.31 0.55 0.64 55
with grilles-between-the-glass PEL-N-152-01273-00002 0.31 0.50 0.57 5511/16" (HA) NaturalSun Low-E IG PEL-N-152-01273-00003 3 3 air 0.31 0.55 0.64 55
with grilles-between-the-glass PEL-N-152-01273-00004 0.31 0.50 0.57 5511/16" (HA) NaturalSun Low-E IG PEL-N-152-01276-00001 5 5 air 0.35 0.53 0.63 50
with grilles-between-the-glass PEL-N-152-01279-00001 0.37 0.48 0.56 50
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission CR = Condensation Resistance
ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-11
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Fixed - 3mm/5mm Glazing N NC SC S CA11/16" Clear IG PEL-N-152-01134-00001 3 5 air 0.46 0.62 0.66 42
with grilles-between-the-glass PEL-N-152-01139-00001 0.47 0.56 0.59 4211/16" Advanced Low-E IG PEL-N-152-01181-00001 3 5 argon 0.28 0.30 0.56 56 NC
with grilles-between-the-glass PEL-N-152-01186-00001 0.29 0.27 0.50 56 NC11/16" SunDefense™ IG PEL-N-152-01203-00001 3 5 argon 0.27 0.23 0.52 57 N NC SC S
with grilles-between-the-glass PEL-N-152-01208-00001 0.29 0.21 0.46 57 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-152-01221-00001 3 5 argon 0.24 0.29 0.55 44 N NC
with grilles-between-the-glass PEL-N-152-01224-00001 0.25 0.27 0.49 44 N NC11/16" NaturalSun Low-E IG PEL-N-152-01163-00001 3 5 argon 0.29 0.55 0.63 56 N 35 CA
with grilles-between-the-glass PEL-N-152-01166-00001 0.30 0.50 0.56 56 N
Fixed - 3mm/5mm Glazing — with Foam Insulation11/16" Advanced Low-E IG PEL-N-152-01299-00001 3 5 argon 0.27 0.30 0.56 57 N NC
with grilles-between-the-glass PEL-N-152-01304-00001 0.28 0.27 0.50 57 NC11/16" SunDefense IG PEL-N-152-01321-00001 3 5 argon 0.27 0.23 0.52 57 N NC SC S
with grilles-between-the-glass PEL-N-152-01326-00001 0.28 0.21 0.46 57 NC SC S11/16" AdvancedComfort Low-E IG PEL-N-152-01339-00001 3 5 argon 0.23 0.29 0.55 44 N NC
with grilles-between-the-glass PEL-N-152-01342-00001 0.24 0.27 0.49 44 N NC11/16" NaturalSun Low-E IG PEL-N-152-01281-00001 3 5 argon 0.28 0.55 0.63 56 N 36 CA
with grilles-between-the-glass PEL-N-152-01284-00001 0.29 0.50 0.56 56 NFixed - 3mm/5mm - High Altitude Glazing11/16" (HA) Advanced Low-E IG PEL-N-152-01170-00001 3 5 air 0.33 0.30 0.56 52
with grilles-between-the-glass PEL-N-152-01175-00001 0.34 0.28 0.50 5211/16" (HA) SunDefense IG PEL-N-152-01192-00001 3 5 air 0.32 0.23 0.52 53 S
with grilles-between-the-glass PEL-N-152-01197-00001 0.34 0.21 0.46 53 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01214-00001 3 5 air 0.27 0.29 0.55 40 N NC
with grilles-between-the-glass PEL-N-152-01217-00001 0.28 0.27 0.49 40 NC11/16" (HA) NaturalSun Low-E IG PEL-N-152-01156-00001 3 5 air 0.33 0.55 0.63 52
with grilles-between-the-glass PEL-N-152-01159-00001 0.35 0.49 0.56 52Fixed - 3mm/5mm - High Altitude Glazing — with Foam Insulation11/16" (HA) Advanced Low-E IG PEL-N-152-01288-00001 3 5 air 0.32 0.30 0.56 53
with grilles-between-the-glass PEL-N-152-01293-00001 0.33 0.28 0.50 5311/16" (HA) SunDefense IG PEL-N-152-01310-00001 3 5 air 0.31 0.23 0.52 53 S
with grilles-between-the-glass PEL-N-152-01315-00001 0.33 0.21 0.46 53 S11/16" (HA) AdvancedComfort Low-E IG PEL-N-152-01332-00001 3 5 air 0.26 0.29 0.55 40 N NC
with grilles-between-the-glass PEL-N-152-01335-00001 0.27 0.27 0.49 40 N NC11/16" (HA) NaturalSun Low-E IG PEL-N-152-01274-00001 3 5 air 0.33 0.55 0.63 52
with grilles-between-the-glass PEL-N-152-01277-00001 0.34 0.49 0.56 52
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-12
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Fixed – Tinted Glazing N NC SC S CA11/16" Bronze Advanced Low-E IG PEL-N-152-01239-00001 5 3 argon 0.28 0.27 0.36 58 NC
with grilles-between-the-glass PEL-N-152-01240-00001 0.29 0.24 0.32 58 NC SC S11/16" Gray Advanced Low-E IG PEL-N-152-01243-00001 5 3 argon 0.28 0.25 0.31 58 NC SC S
with grilles-between-the-glass PEL-N-152-01244-00001 0.29 0.22 0.28 58 NC SC S11/16" Green Advanced Low-E IG PEL-N-152-01247-00001 5 3 argon 0.28 0.30 0.49 58 NC
with grilles-between-the-glass PEL-N-152-01248-00001 0.29 0.27 0.44 58 NC
Fixed – Tinted Glazing — with Foam Insulation11/16" Bronze Advanced Low-E IG PEL-N-152-01357-00001 5 3 argon 0.27 0.27 0.36 58 N NC
with grilles-between-the-glass PEL-N-152-01358-00001 0.28 0.24 0.32 58 NC SC S11/16" Gray Advanced Low-E IG PEL-N-152-01361-00001 5 3 argon 0.27 0.25 0.31 58 N NC SC S
with grilles-between-the-glass PEL-N-152-01362-00001 0.28 0.22 0.28 58 NC SC S11/16" Green Advanced Low-E IG PEL-N-152-01365-00001 5 3 argon 0.27 0.30 0.49 58 N NC
with grilles-between-the-glass PEL-N-152-01366-00001 0.28 0.27 0.44 58 NCFixed – High Altitude Glazing – with Tinted Glazing11/16" Bronze Advanced Low-E IG PEL-N-152-01227-00001 5 3 air 0.32 0.27 0.36 54
with grilles-between-the-glass PEL-N-152-01228-00001 0.34 0.24 0.32 54 S11/16" Gray Advanced Low-E IG PEL-N-152-01231-00001 5 3 air 0.32 0.25 0.31 54 S
with grilles-between-the-glass PEL-N-152-01232-00001 0.34 0.23 0.28 54 S11/16" Green Advanced Low-E IG PEL-N-152-01235-00001 5 3 air 0.32 0.31 0.49 54
with grilles-between-the-glass PEL-N-152-01236-00001 0.34 0.28 0.44 54Fixed – High Altitude Glazing with Foam Insulation and Tinted Glazing11/16" Bronze Advanced Low-E IG PEL-N-152-01345-00001 5 3 air 0.32 0.27 0.36 54
with grilles-between-the-glass PEL-N-152-01346-00001 0.33 0.24 0.32 54 S11/16" Gray Advanced Low-E IG PEL-N-152-01349-00001 5 3 air 0.32 0.25 0.31 54 S
with grilles-between-the-glass PEL-N-152-01350-00001 0.33 0.23 0.28 54 S11/16" Green Advanced Low-E IG PEL-N-152-01353-00001 5 3 air 0.32 0.31 0.49 54
with grilles-between-the-glass PEL-N-152-01354-00001 0.33 0.28 0.44 54
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-13
Impervia® Casement Windows
Glazing Performance – Total UnitG
lazi
ng
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
CR
U. S. Canada 2
Zone ER Zone
Fixed — Laminated Glazing N NC SC S CA11/16" Advanced Low-E IG PEL-N-152-01182-00001 3 6 argon 0.30 0.30 0.55 56 NC
with grilles-between-the-glass PEL-N-152-01187-00001 0.32 0.27 0.49 5611/16" Advanced Low-E IG PEL-N-152-01184-00001 4 7 argon 0.33 0.30 0.55 53
with grilles-between-the-glass PEL-N-152-01189-00001 0.35 0.27 0.49 5311/16" SunDefense™ IG PEL-N-152-01204-00001 3 6 argon 0.29 0.23 0.51 56 NC SC S
with grilles-between-the-glass PEL-N-152-01209-00001 0.31 0.20 0.45 56 S11/16" SunDefense™ IG PEL-N-152-01206-00001 4 7 argon 0.32 0.23 0.51 53 S
with grilles-between-the-glass PEL-N-152-01211-00001 0.35 0.21 0.46 53 S
Fixed — Laminated Glazing with Foam Insulation 11/16" Advanced Low-E IG PEL-N-152-01300-00001 3 6 argon 0.29 0.30 0.55 56 NC
with grilles-between-the-glass PEL-N-152-01305-00001 0.31 0.27 0.49 5611/16" Advanced Low-E IG PEL-N-152-01302-00001 4 7 argon 0.32 0.30 0.55 53
with grilles-between-the-glass PEL-N-152-01307-00001 0.35 0.27 0.49 5311/16" SunDefense™ IG PEL-N-152-01322-00001 3 6 argon 0.29 0.23 0.51 56 NC SC S
with grilles-between-the-glass PEL-N-152-01327-00001 0.30 0.20 0.45 56 NC SC S11/16" SunDefense™ IG PEL-N-152-01324-00001 4 7 argon 0.32 0.23 0.51 53 S
with grilles-between-the-glass PEL-N-152-01329-00001 0.34 0.21 0.46 53 SFixed — Laminated High Altitude Glazing 11/16" Advanced Low-E IG PEL-N-152-01171-00001 3 6 air 0.35 0.30 0.55 51
with grilles-between-the-glass PEL-N-152-01176-00001 0.37 0.27 0.49 5111/16" Advanced Low-E IG PEL-N-152-01173-00001 4 7 air 0.38 0.30 0.55 48
with grilles-between-the-glass PEL-N-152-01178-00001 0.41 0.27 0.49 4811/16" SunDefense IG PEL-N-152-01193-00001 3 6 air 0.35 0.23 0.51 51 S
with grilles-between-the-glass PEL-N-152-01198-00001 0.37 0.21 0.45 51 S11/16" SunDefense IG PEL-N-152-01195-00001 4 7 air 0.38 0.24 0.51 48 S
with grilles-between-the-glass PEL-N-152-01200-00001 0.41 0.21 0.46 48Fixed — Laminated High Altitude Glazing with Foam Insulation 11/16" Advanced Low-E IG PEL-N-152-01289-00001 3 6 air 0.34 0.30 0.55 51
with grilles-between-the-glass PEL-N-152-01294-00001 0.36 0.27 0.49 5111/16" Advanced Low-E IG PEL-N-152-01291-00001 4 7 air 0.37 0.30 0.55 48
with grilles-between-the-glass PEL-N-152-01296-00001 0.40 0.27 0.49 4811/16" SunDefense IG PEL-N-152-01311-00001 3 6 air 0.34 0.23 0.51 52 S
with grilles-between-the-glass PEL-N-152-01316-00001 0.36 0.21 0.45 52 S11/16" SunDefense IG PEL-N-152-01313-00001 4 7 air 0.37 0.24 0.51 49 S
with grilles-between-the-glass PEL-N-152-01318-00001 0.40 0.21 0.46 49 S
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
For center-glass values, see the Product Performance section.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
CA
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-14
Impervia® Casement Windows
Combinations, Grilles
A combination is defined as an assembly formed by two or more separate windows or doors whose frames are mulled together utilizing a combination mullion or reinforcing mullion.
Below are available factory-assembled combinations. See the Combination section for requirements and limitations related to mulling various combinations plus configuration size range information.
2-wide 3-Wide equal 4-wide
3-wide unequal Center fixed with flankers Transom over single unit
Downloadable PDF file.
Click here for the Impervia Combinations Section
Grille Profiles GRILLES-BETWEEN-THE-GLASS
3/4" Contour
3/4"
Grille Patterns
Traditional Custom - Equally Divided
Standard corner lite dimension for Prairie patterns = 4" visible glass (VG).
(1) Standard visible glass to center line of separator bar = 14" or half the total visible glass height, whichever is smaller. Multiple rows are available up to 50% glass size.
Pattern availability may vary depending on size of unit.
VG = Visible Glass
Lite dimensions noted can vary.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-15
Impervia® Casement Windows
Size Tables
1-6/6-0 2-0/6-0 3-0/6-02-8/6-02-6/6-02-4/6-0
1-6/5-6 2-0/5-6 3-0/5-62-8/5-62-6/5-62-4/5-6
1-6/2-6 2-0/2-6 2-4/2-6 2-6/2-6 2-8/2-6 3-0/2-6
1-6/5-0 2-0/5-0 2-8/5-0 3-0/5-02-6/5-02-4/5-0
1-6/3-0
1-6/3-6
1-6/4-0
2-0/3-0
2-0/3-6
2-0/4-0
2-4/4-6
2-4/4-0
2-4/3-6
2-4/3-0
2-6/4-6
2-6/4-0
2-6/3-6
2-6/3-0
2-8/4-6
2-8/4-0
2-8/3-6
2-8/3-0
3-0/4-6
3-0/4-0
3-0/3-6
3-0/3-0
2-0/4-61-6/4-6
1-6/1-2
1-6/1-6
1-6/2-0
2-0/1-2
2-0/1-6
2-0/2-0 2-4/2-0
2-4/1-6
2-4/1-2
2-6/2-0
2-6/1-6
2-6/1-2
2-8/2-0
2-8/1-6
2-8/1-2
3-0/2-0
3-0/1-6
3-0/1-2
Vent and Fixed Units
Transoms
"/ 21
"/ 21
"/ 21
1' 5
1' 1
1' 1
1"
/ 21"
/ 21"
/ 21"
/ 21"
/ 21"
/ 21"
/ 21"
/ 21
"/ 21"/ 21"/ 21"/ 21"/ 21"/ 21
TTTTT T
2' 6
"2'
5(762
)(7
49)
6' 0
"5'
11
(1 8
29)
(1 8
16)
5' 6
"5'
5
(1 6
76)
(1 6
64)
4' 1
1
(1 5
24)
(1 5
11)
5' 0
"
FrameOpening
(1 3
59)
(1 3
72)
4' 5
4' 6
"(1
207
)(1
219
)
3' 1
14'
0"
3' 6
"3'
5
(1 0
67)
(1 0
54)
3' 0
"2'
11
(914
)(9
02)
(445
)(4
57)
1' 6
"1'
2"
(356
)(3
43)
(597
)(6
10)
2' 0
"
2' 6"2' 5
(762)(749)
2' 4"2' 3
(711)(699)
2' 0"1' 11
(610)(597)
1' 6"1' 5
(457)(445) (800)
(813)
2' 72' 8"
2' 113' 0"
(914)(902)
2E3E 1E
1E1E E
E E E
EEE
E E E
EEE
E E E
3E
2E
2E
2E
2E
2E
2E
SPEC
IAL
SIZE
S AV
AILA
BLE
SPEC
IAL S
HORT
ER AN
D TA
LLER
SIZE
S AVA
ILABL
E
SPECIAL NARROWER AND WIDER SIZES AVAILABLE
Egress Notes:Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
T = Tempered glass.
Not to scale.
Any vent casement with frame height greater than 70" will have 3mm tempered glass to reduce sash weight.
All units are available as fixed in the Casement section.
Traditional grille patterns shown. See Grilles in the Overview section for additional patterns and profiles.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-16
Impervia® Casement Windows
Size Tables
SPECIAL NARROWER AND WIDER SIZES AVAILABLE
SPEC
IAL
SIZE
S AV
AILA
BLE
SPEC
IAL
SHO
RTER
AN
D T
ALLE
R S
IZES
AVA
ILAB
LE
6-0/6-05-0/6-04-0/6-0
6-0/5-65-0/5-64-0/5-6
6-0/5-0
6-0/4-6
6-0/4-0
6-0/3-6
6-0/3-0
5-0/5-0
5-0/4-6
5-0/4-0
5-0/3-6
5-0/3-0
4-0/5-0
4-0/4-6
4-0/4-0
4-0/3-6
4-0/3-0
6-0/2-0
6-0/1-6
6-0/1-2
5-0/2-0
5-0/1-6
5-0/1-2
4-0/2-0
4-0/1-6
4-0/1-2
Fixed Units
Transoms
"/21"/21"/21
"/ 21
"/ 21
"/ 21
(445
)(4
57)
1' 5
1' 6
"1'
11'
2"
(356
)(3
43)
(597
)(6
10)
1' 1
12'
0"
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
6' 0
"5'
11
(1 8
29)
(1 8
16)
5' 6
"5'
5
(1 6
76)
(1 6
64)
4' 1
1
(1 5
24)
(1 5
11)
5' 0
"
(1 3
59)
(1 3
72)
4' 5
4' 6
"
(1 2
07)
(1 2
19)
3' 1
14'
0"
3' 6
"3'
5
(1 0
67)
(1 0
54)
3' 0
"2'
11
(914
)(9
02)
5' 116' 0"
(1 829)(1 816)
4' 115' 0"
(1 524)(1 511)
3' 114' 0"
(1 219)(1 207)
Frame
Opening
Not to scale.
Traditional grille patterns shown. See Grilles in the Overview section for additional patterns and profiles.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-17
Impervia® Casement Windows
Special Sizes and Dimensions
Special Size Frame Dimensions*
Minimum Maximum
Vent1' 5-1/2" W x 1' 8" H
(17-1/2" x 20")(445 x 508)
3' 1-1/2" W x 6' 7-1/2" H(37-1/2" x 79-1/2")
(953 x 2 019)
Fixed1' 1-1/2" W x 11-1/2" H
(13-1/2" x 11-1/2")(343 x 292)
5' 11-1/2" W x 6' 7-1/2" H(71-1/2" x 79-1/2")
(1 816 x 2 019)
Fixed Sizes
Vent Sizes
17.5"
37.5"
20"
79.5"
MAX. SIZE
MIN. SIZE
MAX. SIZE
13.5"71.5"
11.5
"
79.5"
MIN. SIZE
* Available within size range shown.
Keep frame di men sions to the near est 1/8" increment. Frame width cannot exceed frame height on special size vent units.
Miscellaneous Formulas
Formula
Visible Glass
Width = Frame – 5-7/16" Height = Frame – 5-7/16"
Actual Glass
Width = Frame – 4-3/8" Height = Frame – 4-3/8"
Clear Opening Height
Frame Height − 4-7/16"
Clear Opening Width
Hinge Frame Width Formula
Standard 29" to 29-1/2" FW − 9"
Standard >29-1/2" to 37-1/2" FW − 9-11/16"
Side Pivot ≥ 25" to ≤ 32" FW − 4-1/8"
Vent Opening Area
(FW − 6.518) × (FH − 5.641) ÷ 144
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-18
Impervia® Casement Windows
Design Data
Vent
Unit
Eg
ress Clear Opening Vent
Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm) Performance
Class & Grade1 Width (Inches)
Height (Inches) Ft
2 Annealed Tempered
1-6/2-6 7-13/16 25-1/16 1.3 1.8 2.0 2.5 3 LC501-6/3-0 7-13/16 31-1/16 1.6 2.3 2.5 2.5 3 LC501-6/3-6 7-13/16 37-1/16 2.0 2.7 3.0 2.5 3 LC501-6/4-0 7-13/16 43-1/16 2.3 3.2 3.5 2.5 3 LC501-6/4-6 7-13/16 49-1/16 2.6 3.6 4.0 2.5 3 LC501-6/5-0 7-13/16 55-1/16 2.9 4.1 4.5 2.5 3 LC501-6/5-6 7-13/16 61-1/16 3.3 4.6 5.0 2.5 3 LC50
1-6/6-0 T 7-13/16 67-1/16 3.6 5.0 5.5 – 3 LC502-0/2-6 13-13/16 25-1/16 2.4 2.8 3.0 2.5 3 LC502-0/3-0 13-13/16 31-1/16 2.9 3.5 3.7 2.5 3 LC502-0/3-6 13-13/16 37-1/16 3.5 4.2 4.5 2.5 3 LC502-0/4-0 13-13/16 43-1/16 4.1 4.9 5.2 2.5 3 LC502-0/4-6 13-13/16 49-1/16 4.7 5.6 6.0 2.5 3 LC502-0/5-0 13-13/16 55-1/16 5.2 6.4 6.7 2.5 3 LC45/LC502-0/5-6 13-13/16 61-1/16 5.8 7.1 7.5 2.5 3 LC40/LC50
2-0/6-0 T 13-13/16 67-1/16 6.4 7.8 8.2 – 3 LC502-4/2-6 17-13/16 25-1/16 3.1 3.5 3.6 2.5 3 LC502-4/3-0 E3 23-3/8 31-1/16 5.0 4.4 4.6 2.5 3 LC502-4/3-6 E2 23-3/8 37-1/16 6.0 5.2 5.5 2.5 3 LC502-4/4-0 E2 23-3/8 43-1/16 7.0 6.1 6.4 2.5 3 LC502-4/4-6 E2 23-3/8 49-1/16 7.9 7.0 7.3 2.5 3 LC502-4/5-0 E2 23-3/8 55-1/16 8.9 7.8 8.2 2.5 3 LC45/LC502-4/5-6 E2 23-3/8 61-1/16 9.9 8.7 9.1 2.5 3 LC40/LC50
2-4/6-0 T E2 23-3/8 67-1/16 10.9 9.6 10.1 – 3 LC502-6/2-6 20-1/2 25-1/16 3.5 3.8 4.0 2.5 3 LC502-6/3-0 E3 25-3/8 31-1/16 3.5 4.8 5.0 2.5 3 LC502-6/3-6 E1 25-3/8 37-1/16 4.4 5.7 6.0 2.5 3 LC502-6/4-0 E 25-3/8 43-1/16 5.2 6.7 7.0 2.5 3 LC502-6/4-6 E 25-3/8 49-1/16 6.1 7.6 8.0 2.5 3 LC502-6/5-0 E 25-3/8 55-1/16 6.9 8.6 9.0 2.5 3 LC45/LC502-6/5-6 E 25-3/8 61-1/16 9.0 9.6 10.0 2.5 3 LC40/LC50
2-6/6-0 T E 25-3/8 67-1/16 11.8 10.5 11.0 3 3 LC502-8/2-6 21-13/16 25-1/16 3.8 4.1 4.3 2.5 3 LC502-8/3-0 E2 27-3/8 31-1/16 5.9 5.2 5.4 2.5 3 LC502-8/3-6 E1 27-3/8 37-1/16 7.0 6.2 6.5 2.5 3 LC502-8/4-0 E 27-3/8 43-1/16 8.1 7.3 7.6 2.5 3 LC502-8/4-6 E 27-3/8 49-1/16 9.3 8.3 8.6 2.5 3 LC502-8/5-0 E 27-3/8 55-1/16 10.4 9.3 9.7 2.5 3 LC502-8/5-6 E 27-3/8 61-1/16 11.6 10.4 10.8 3 3 LC50
2-8/6-0 T E 27-3/8 67-1/16 12.7 11.4 11.9 – 3 LC503-0/2-6 25-13/16 25-1/16 4.4 4.8 5.0 2.5 3 LC503-0/3-0 E1 25-13/16 31-1/16 5.5 6.0 6.2 2.5 3 LC503-0/3-6 E 25-13/16 37-1/16 6.6 7.2 7.5 2.5 3 LC503-0/4-0 E 25-13/16 43-1/16 7.7 8.4 8.7 2.5 3 LC503-0/4-6 E 25-13/16 49-1/16 8.7 9.6 10.0 2.5 3 LC45/LC503-0/5-0 E 25-13/16 55-1/16 9.8 10.8 11.2 3 3 LC503-0/5-6 E 25-13/16 61-1/16 10.9 12.0 12.5 3 3 LC50
3-0/6-0 T E 25-13/16 67-1/16 12.0 13.3 13.7 – 3 LC50
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where shown, requires tempered glass.
T=Any vent casement with frame height greater than 70" will have 3mm tempered glass to reduce sash weight.
To convert areas to square meters (m²), multiply square feet by 0.0929.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-19
Impervia® Casement Windows
Design Data
Transom Units
Unit Visible Glass Ft2
Standard Glass Thickness (mm) Performance
Class & Grade 1Annealed Tempered
1-6/1-2 0.6 2.5 3 LC501-6/1-6 1.0 2.5 3 LC501-6/2-0 1.5 2.5 3 LC502-0/1-2 1.0 2.5 3 LC502-0/1-6 1.5 2.5 3 LC502-0/2-0 2.2 2.5 3 LC502-4/1-2 1.2 2.5 3 LC502-4/1-6 1.8 2.5 3 LC502-4/2-0 2.7 2.5 3 LC502-6/1-2 1.3 2.5 3 LC502-6/1-6 2.0 2.5 3 LC502-6/2-0 3.0 2.5 3 LC502-8/1-2 1.4 2.5 3 LC502-8/1-6 2.1 2.5 3 LC502-8/2-0 3.2 2.5 3 LC503-0/1-2 1.6 2.5 3 LC503-0/1-6 2.5 2.5 3 LC503-0/2-0 3.7 2.5 3 LC504-0/1-2 2.3 2.5 3 LC504-0/1-6 3.5 2.5 3 LC504-0/2-0 5.2 2.5 3 LC50
5-0/1-2 T 3.0 – 3 LC505-0/1-6 4.5 2.5 3 LC505-0/2-0 6.7 2.5 3 LC50
6-0/1-2 T 3.6 – 3 LC456-0/1-6 T 5.5 – 3 LC456-0/2-0 8.2 2.5 3 LC35/LC45
Fixed Units
Unit Visible Glass Ft2
Standard Glass Thickness (mm) Performance
Class & Grade 1Annealed Tempered
3-0/3-0 6.2 2.5 3 LC503-0/3-6 7.5 2.5 3 LC503-0/4-0 8.7 2.5 3 LC503-0/4-6 10.0 2.5 3 LC45/LC503-0/5-0 11.2 3 3 LC503-0/5-6 12.5 3 3 LC503-0/6-0 13.7 3 3 LC45/LC504-0/3-0 8.7 2.5 3 LC504-0/3-6 10.5 3 3 LC504-0/4-0 12.2 3 3 LC504-0/4-6 14.0 3 3 LC504-0/5-0 15.7 3 3 LC45/LC504-0/5-6 17.5 5 5 LC504-0/6-0 19.2 5 5 LC505-0/3-0 11.2 3 3 LC505-0/3-6 13.5 3 3 LC505-0/4-0 15.7 3 3 LC45/LC505-0/4-6 18.0 5 5 LC505-0/5-0 20.2 5 5 LC505-0/5-6 22.5 5 5 LC505-0/6-0 24.7 5 5 LC506-0/3-0 13.7 3 3 LC456-0/3-6 16.5 3 3 LC456-0/4-0 19.2 5 5 LC456-0/4-6 22.0 5 5 LC456-0/5-0 24.7 5 5 LC456-0/5-6 27.5 5 5 LC456-0/6-0 30.2 5 5 LC45
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where shown, requires tempered glass.
To convert areas to square meters (m²), multiply square feet by 0.0929.
-
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com F-CM-20
Impervia® Casement Windows
Detailed Product Description
Frame • Frame is Duracast—five-layer pultruded fiberglass material [with optional
foam insulation 1] reinforced with a Pella patented interlocking mat. • Overall frame depth is 3-1/4". • Nominal wall thickness of Duracast® fiberglass composite members is
.050" to .070" thick.• Frame corners are mitered, joined and bonded with corner lock and
injected with polyurethane adhesive. • Jambs contain factory-drilled installation screw holes on block frame.
Sash • Sash is Duracast fiberglass composite — five-layer pultruded fiberglass
material, reinforced with a Pella patented interlocking mat. • All sash members have mitered corners bonded with corner lock and
sealed with injected polyurethane adhesive.
Exterior / Interior• Duracast fiberglass composite surfaces with powder-coat paint finish.
Color is [White] [Tan] [Brown] [Black] [Morning Sky Gray].- or -
Dual-color option [Tan] [Brown] [Black] [Morning Sky Gray] exterior with White interior 2.
Glazing System• Quality float glass complying with ASTM C 1036.
11/16" insulating glass [[annealed] [tempered]] [obscure 3] [clear] [[Advanced] [SunDefense™] [AdvancedComfort] [NaturalSun] Low-E coated, [with argon]]] [[bronze] [gray] [green] Advanced Low-E [with Argon]] sealed and bonded to sash.
• High altitude glazing available.
WeatherstrippingDual Weatherstripping• Continuous, flexible ThermoPlastic Vulcanizate material in dual durometer
design, compressed between frame and sash for positive seal on all four sides.
• Secondary ThermoPlastic Vulcanizate leaf-type weatherstrip between edge of sash and frame.
Hardware • Roto operator assembly
Steel worm gear sash operator with hardened gears. Operator base is zinc die cast with painted finish. Operator linkage, hinge slide, and hinge arms are 300 series stainless
steel. Exposed fasteners are stainless steel. Hardware shall exceed 1,000 hours salt spray exposure per
ASTM B 117. • Finish of integrated folding crank is [baked enamel [White] [Brown] [Tan]
[Matte Black] [Morning Sky Gray]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze]. All vent units are available with left- or right-hand hinging.
• SureLock® System—A single handle locking system operates positive-acting arms that reach out and pull the sash into a locked position: one installed on units 27-1/2" and smaller frame height, two unison operating locks installed on units over 27-1/2" frame height.
• Lock handle finish is [baked enamel [White] [Brown] [Tan] [Matte Black] [Morning Sky Gray]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze].
Optional ProductsScreens• Conventional Black Vinyl-coated 18/16 mesh fiberglass screen cloth
complying with ASTM D 3656 and SMA 1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
• InView™ screens Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA
1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
Screen frame finish is baked enamel, color to match interior.Grilles• Grilles-Between-the-Glass
Insulating glass contains 3/4" contoured aluminum grilles permanently installed between two panes of glass.
Grilles are factory prefinished [White] [Tan] [Brown] [Black] [Morning Sky Gray] to match interior and exterior finish.
Hardware• Optional factory applied limited opening hardware available for vent units
in stainless steel; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Casement
HINGE JAMBHJLOCK JAMBLJ
SILLS
HEADH
(1) Foam insulation inserts are not available with clear glazing.
(2) Dual-color finish is not available on products with integral nailing fin.
(3) Obscure glazing is not available when AdvancedComfort Low-E coated IG is specified.
Foam Insulation Inserts 1
-
F-CM-21
Impervia® Casement Windows
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com
Unit Sections - Frame Types
[29]1 1/8"
[30]
1 3/
16"
[33]1 5/16"
[49]1 15/16"
[37]
1 7/
16"
[33]
1 5/
16"
[19]
3/4"
[52]
2 1/
16"
[29]1 1/8"
[29]1 1/8"
[29]1 1/8"
[29]1 1/8"
[30]
1 3/
16"
[33]1 5/16"
[49]1 15/16"
[37]
1 7/
16"
[33]
1 5/
16"
[19]
3/4"
[52]
2 1/
16"
[32]
1 1/
4"
[60]2 3/8"
[23]7/8"
[37]
1 7/
16"
[33]
1 5/
16"
[19]
3/4"
[52]
2 1/
16"
[32]
1 1/
4"
[33]1 5/16"
[49]1 15/16"
[52]
2 1/
16"
[37]
1 7/
16"
[33]
1 5/
16"
[19]
3/4"
[52]
2 1/
16"
[37]
1 7/
16"
[33]
1 5/
16"
[19]
3/4"
[83]3 1/4"
GLAZING OPTIONS
REPLACEMENT FRAME
NEW CONSTRUCTION FRAME
Standard Block Frame with Off Set FinIntegral Nailing Fin
11/16" IG
Standard Block Frame
Standard Block Frame with Standard Fin
Scale 3" = 1' 0"
All dimensions are approximate.
-
F-CM-22
Impervia® Casement Windows
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com
Unit Sections
OFF SET FINwith
STANDARD FINwith
[32]1 1/4"
[23]
7/8"
[60]
2 3/
8"
[49]
1 15
/16"
[33]
1 5/
16"
[32]1 1/4"
[29]
1 1/
8"
[29]1 1/8"
[29]
1 1/
8"
[48]1 7/8"
[52]
2 1/
16"
[60]
2 3/
8"
FRAME WIDTH
[33]1 5/16"
[37]1 7/16"
[19]3/4"
[70]2 3/4"
FRA
ME
HE
IGH
T
[33]
1 5/
16"
[37]
1 7/
16"
[70]
2 3/
4"
FRA
ME
HE
IGH
T
[52]2 1/16"
FRAME WIDTH
[33]1 5/16"
[37]1 7/16"
[19]3/4"
[70]2 3/4"
[83]3 1/4"
[29]1 1/8"
[33]
1 5/
16"
[37]
1 7/
16"
[83]3 1/4"
[52]
2 1/
16"
[60]
2 3/
8"
[70]
2 3/
4"
FRA
ME
FRA
ME
FRAME FRAMEFRAME FRAME
VERTICAL JOINING MULLION
JAMBVENT
JAMBVENT
JAMBFIXED
JAMBVENT
HEAD
FIXED SILL(Transom)
HORIZONTAL JOINING MULLION VERTICAL JOINING MULLION
COMBINATION
BLOCK FRAME
VS
VH
LJ HJ
FH
FJ
FS
FJ FIXED JAMB
FS FIXED SILL
FH FIXED HEAD
LOCK JAMBLJ HINGE JAMBHJ
VS VENT SILL
VH VENT HEAD
Scale 3" = 1' 0"
All dimensions are approximate.
See the Installation and Performance section on PellaADM.com for mullion applications and structural limitations.
-
F-CM-23
Impervia® Casement Windows
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com
Unit Sections - Integral Fin
[52]2 1/16"
[29]
1 1/
8"
[29]1 1/8"
[29]
1 1/
8"[29]1 1/8"
[52]2 1/16"
[31]
1 1/
4"[3
1]1
1/4"
INTEGRAL NAILING FIN
[33]
1 5/
16"
FRAME WIDTH
[33]1 5/16"
[37]1 7/16"
[19]3/4"
[31]1 1/4"
[70]2 3/4"
FRA
ME
HE
IGH
T
[33]
1 5/
16"
[37]
1 7/
16"
[49]1 15/16"
[33]1 5/16"
[52]
2 1/
16"
[60]
2 3/
8"
[70]
2 3/
4"
[83]
3 1/
4"[49
]1
15/1
6"[3
3]1
5/16
"
FRAME WIDTH
[33]1 5/16"
[37]1 7/16"
[19]3/4"
[31]1 1/4"
[70]2 3/4"
FRA
ME
HE
IGH
T
[33]
1 5/
16"
[37]
1 7/
16"
[49]1 15/16"
[33]1 5/16"
[52]
2 1/
16"
[60]
2 3/
8"
[70]
2 3/
4"
[83]
3 1/
4"[49
]1
15/1
6"
FH
VS
VH
LJ HJ
FJ
FS
FJ FIXED JAMB
LOCK JAMBLJ HINGE JAMBHJ
VS VENT SILL
VH VENT HEAD
FS FIXED SILL
FH FIXED HEAD
Scale 3" = 1' 0"
All dimensions are approximate.
Product Selection GuideSize and Performance Data Features and Options
Sound Transmission Class Outdoor Indoor Transmission ClassGlazing PerformanceCombination AssembliesGrille TypesSize TablesSpecial Sizes and DimensionsDesign DataDetailed Product DescriptionsUnit SectionsBlock FrameNail Fin Frame