Part GAngled Brace

Part DUpper Worksurface

Sit-Stand Desk ConverterUPL147~clamp

Part ALifting Mechanismand Paddle

Part MM6*8 Bolts Qty. 10

Part NM6*10 Bolts Qty. 2

Part OM6*12 Bolts Qty. 10

Part PM6*35 Bolts Qty. 2

Part QPaddle Mounts Qty. 2

Part LM8*70.5 Bolts Qty. 2

Part KAllen Wrench (small)

Part JAllen Wrench (large)

Part CFront Panel

Parts FVertical Connector (short & long heights)

Part BKeyboard Tray

Step 3Using the smaller Allen Wrench (part K) and two (2) of the M6*12 Bolts (part O), attach either the longer or shorter Vertical Connector (part F) to the Front Panel (part C).

Step 1With the Upper Worksurface (part D) placed upside down, line up the holes on the Lifting Mechanism (part A) with the holes on the underside of the Upper Worksurface (part D) as shown. Attach using the smaller Allen Wrench (part K) and four (4) of the M6*12 Bolts (part O).

®

Step 2Choose which side you would like the release paddle on, and attach at the pre-existing holes on that side, using the two (2) M6*35 Bolts (part P), the smaller Allen Wrench (part K) and the two (2) Paddle Mounts (part Q).

Part ETop Clamp

Part IClamping Plate

Part HBottom Clamp

UPLIFT Desk • 1-800-349-3839 • info@upliftdesk.com • www.upliftdesk.com

Step 6a. Measure your desktop thickness. The thickness of your desktop will determine how you should attach the Bottom Clamp (part H) to the Top Clamp (part E). See the diagram to the left.

b. Connect the Top Clamp (part E) and the Bottom Clamp (part H) as shown with the two M6*10 Bolts (part N) and the smaller Allen Wrench (part K).

c. Slide the clamp mount assembly onto the back edge of your desktop. Hold the Clamping Plate (part I) in place against the under side of the desktop, and line up its holes with the holes on the Bottom Clamp (part H). Secure the clamp mount assembly into place by tightening the two M8*70.5 Bolts (part L) with the smaller Allen Wrench (part K).

a.

Step 5Turn the Keyboard Tray (part B) upside down and attach to the bottom of the Vertical Connector (part F) using two (2) M6*8 Bolts (part M) and the smaller Allen Wrench (part K).

Step 4Attach the front panel-vertical connector assembly (assembled in step 3) to the front of the Lifting Mechanism (part A) with the smaller Allen Wrench (part K) and four (4) of the M6*12 Bolts (part O).

for desks 1.5” or thinner,

turn the Bottom Clamp like this

for desks from 1.51” to 2.9” max, turn the Bottom

Clamp like this

b.

c.

UPLIFT Desk • 1-800-349-3839 • info@upliftdesk.com • www.upliftdesk.com

a.

Step 7Prepare the lifting mechanism-work surface assembly (which was completed in step 5) to be mounted onto the clamp mount assembly (which was completed in step 6).

Hold the Lifting Mechanism securely with one hand while squeezing the Paddle with the other, slowly releasing the Lifting Mechanism to its highest point.

Step 8a. Determine the depth of your desk, and refer to the diagram to the left. For shallow desktops (23.5’’ minimum depth) place further back on the clamp, and for deep desktops (31.5’’ maximum depth) place forward on the clamp.

Note: Attach the unit to the clamp mount assembly in a position that allows the Keyboard Tray to clear the front edge of the desk.

b. Turn the lifting mechanism assembly right-side up, and attach to the clamp mount assembly in the appropriate position for your desktop depth, using four (4) of the M6*8 Bolts (part M) and the smaller Allen Wrench (part K).

c. Secure the unit in place by attaching the Angled Brace (part G)at the back of the Lifting Mechanism (part A) where it meets the clamp mount assembly with four (4) of the M6*8 Bolts (part M) and the smaller Allen Wrench (part K).

Step 9With the unit at a 45° angle, adjust the tension for smooth operation using the larger Allen Wrench (part J) and the tension adjustment bolt on the rear of the unit. Turn clockwise to lessen the tension or counterclockwise to increase it. You may need to make further adjustments once equipment, such as a monitor and keyboard, is placed on the unit.

b.

For shallow desks, place toward back of clamp

For deep desks, place toward front of clamp

c.

UPLIFT Desk • 1-800-349-3839 • info@upliftdesk.com • www.upliftdesk.com

Step 10Adjust the height of the unit by squeezing the release Paddle and moving to desired position.

UPLIFT Desk • 1-800-349-3839 • info@upliftdesk.com • www.upliftdesk.com

The maximum load capacity of the UPLIFT Sit-Stand Desk Converter is 28.6 lbs. Please do not overload.

Please note

•