Simba 1354
-
Upload
manuel-uturunco-aguilar -
Category
Documents
-
view
238 -
download
0
Transcript of Simba 1354
8/10/2019 Simba 1354
http://slidepdf.com/reader/full/simba-1354 1/4
Atlas Copco
Technical specification
Simba 364-ITH
Production drilling rigs
Standard features
»ITH-hammerPneumatic in the hole hammer, ITH (hammer not•supplied with rig)Rotation unit DHR 6•
Drilling unit»
Mechanized rod handling system•Feed with hydraulic two-stage cylinder •Front- and rear-mounted stingers•Breakout table for guidance during collaring and•as support during rod handling
Positioning unit»Tilt, rotation, pendulum arm and slide table•Accurate and smooth movements•Mine-adapted, sturdy components•
Control system»Electrical Direct System (EDS)•Anti-jamming system•
Carrier»Mine-adapted carrier for small- to medium-sized drifts with•
articulated steering and four-wheel drive
General»Trolley-mounted operator panel•FOPS-approved protective roof •Electrical cable reel•Working lights on tripods•
Production drilling rig with pneumatic in the hole hammer, ITH, fordeep straight holes. Ring drilling with parallel holes upwards/down-wards up to 3 m apart. Hole diameter 90–178 mm.
8/10/2019 Simba 1354
http://slidepdf.com/reader/full/simba-1354 2/4
Simba 364-ITH
Specifications
ROTATION UNIT
DHR 6H
56
DHR 6H
68
Length with fixed adapter 530 mm
Length with floating adapter 840 mm
Torque, max. 6 000 Nm
Rotation speed 0–107 rpm 0–68 rpm
Adapter fixed API 23
/8’’ or API 3½ ’’ Reg femAdapter floating FLT API 23 /8’’ or 3 ½’’ Reg femWeight with/without floating sub 243/182 kg
Power pack»
Hydraulic pump for rotation, positioning, feed•Pumps unloaded at start•
System pressure, max• .................................................. 250 bar Hydraulic oil tank, volume max/min• .............................. 160 lLow oil level indicator •Oil temperature gauge on oil tank •Electrical oil flling pump•Filtration, absolute• ......................................................... 16 μmOil flter indicator •Water cooled oil cooler in stainless steel•Mineral hydraulic oil•
Drilling unit»
Rod Handling System, RHS 27• ..............................27+1 pipesAdaptable to 5′ and 6′ pipes•Adaptable to 76 and 89 mm drill pipes•Mechanized drilling up to 51 m•
FEED
BMH 200-series BMH 235 BMH 236
Total length 3 200 mm 3 510 mm
Drill steel length 1 500 mm 1 800 mm
Total length with extractor 3 500 mm 3 810 mm
Positioning system»
Feed extension (with 4′ drill pipe)• ............................. 900 mmFeed extension (with 5′ and 6′ drill pipe)• ................ 1 200 mmRotary Acurator BHR 60–2 for 360º ring drilling•Sliding table BHT 150 gives 1.5 m feed parallel positioning•Pendulum arm, BHP 150 gives 1.5 m feed parallel positioning•in the side walls. Adds additional 1.5 m feed parallel position-ing upwards/downwards.
Stinger backward on feed• .......................................BSJ 8-200Stinger forward on feed• ..........................................BSJ 8-115Feed dump, drilling• ..............+20º forward and -65º backward
Carrier»
Deutz 4-cylinder D914 L04, EPA III/COM III (Tier 3/Stage•IIIA) approved 4-stroke prechamber diesel engine
Power rating at 2 300 rpm• ................................ 55 kW (75 hp)Torque at 1 550 rpm• ...................................................230 NmFixed seat for tramming, including safety belt•Articulated steering• .................................. ±41° steering angleFour-wheel drive•FOPS-approved protective roof •Hydrostatic power steering system•Hydrodynamic transmission• .................................Clark 12000Front axle• ................................................................ Dana 176Rear axle• .......................................... Dana 176, ±8º oscillationAutomatic differential lock on front axle, limited slip•Tyres• .....................................................................12.00 x R20Clearence outside axles• ...................................................... 15ºHydraulic jacks, front• .......................................... 2 extendableHydraulic jacks, rear • ..............................................................2Service brakes• 2 separate circuits (hydraulically applied, fullyenclosed wet disc brakes)Emergency and parking brakes• .....................................SAHR Fuel tank, volume• .............................................................. 60 lElectric system• .................................................................24 VBatteries• ....................................................................2 x 70 AhTramming lights• ........................................................8 x 70 WBrake lights•Illuminated stairs for platform•Central lubrication system•Silencer and catalyser •Fire extinguisher •Spirit levels•Gradeability at max load on drive wheels• .......................... 1:4
Tramming speed on at ground• ............................... >10 km/hTramming speed on incline 1:8• .................................. >4 km/hHorn, beacon and reverse alarm•Outlet for communication radio• .......................................12 V
Electrical system»
Total installed power • .....................................................65 kWMain motor at 50 Hz• .....................................................55 kWVoltage• .................................................................380–1 000 VFrequency• .................................................................50–60 HzStarting method• .........star/delta (380–690 V) direct (1 000 V)Thermal overload protection for electric motors•Percussion hour meters on A-panel•Digital volt/amperage meter in electric cabinet•Phase sequence indicator •Earth fault indicator •Battery charger •Transformer • ....................................................................4 kVACable reel•Limit switch for cable reel•Working lights on tripods• ...............................2 x 200 W, 24 V
Water system»
Water injection pump•Capacity• .............................................................. max 50 l/minMin water inlet pressure• .................................................. 2 bar Hydraulic drive, axial piston motor• ............................... 10 ccWater pressure gauge•
2-inch system•High and low percussion•HECL lubrication system with electric flling pump•
Air pressure gauge and air ow gauge•
Air system»
Control system»
Electrical Direct System, EDS•Basic functions such as semi-automatic drilling and anti-jam-•ming included
8/10/2019 Simba 1354
http://slidepdf.com/reader/full/simba-1354 3/4
Simba 364-ITH
Specifications
Optional equipment
Drilling system»ITH lubrication surveillance system•Floating sub•
Positioning system»Rig alignment laser RAL 650•Additional stinger backward on feed, BSJ 8-200 (stroke•length 2 000 mmAutomatic lubrication for positioning/drilling system•Central lubrication for positioning/drilling system•Thread lubrication kit•Angle reading instrument (ARI 6 C), with or without hole•depth measurement
Power pack»Heater kit•
Electrical system»Electrical cable on reel, H07RN-F•Electrical cable on reel, Buex•Plug PC4/PC5•Socket PC4/PC5•Switch gear •Working lights on tripods, 2 x 500 W, 230 V•Electrics according to local standards•
Carrier»Fire suppression system ANSUL, manual•Manual spotlight•
Miscellaneous»Manual rig washing kit•Manual lubrication kit• Ni-Cr plated piston rods•
DRILL STRING
ITH-hammer Hole diameter, mm Drill pipes, mm Pipe length, mm Thread pin/box
COP 34 90–105 76 1 800 2 3/8” API Reg
COP 44 105–130 89 1 500/1 800 2 3/8” API Reg
COP 54 GE 130–152 89 1 500/1 800 2 3/8” API Reg
COP 64 Gold 156–178 114 1 500 3 1/2” API Reg
8/10/2019 Simba 1354
http://slidepdf.com/reader/full/simba-1354 4/4
Simba 364-ITH
9 8 5 1 2
5 5 5
0 1 a
1 1 / 2 0 0 8
© C
o p y r i g h t 2 0 0 8 ,
A t l a s
C o p c o R o c k D r i l l s A B ,
Ö r e b r o ,
S w e d e n .
A l l p r o d u c t n a m e s i n t h i s p u b l i c a t i o n a r e t r a d e m a r k s o f A t l a s C o p c o .
A n y u n a u t h o r i z e d u s e o r c o p
y i n g o f t h e c o n t e n t s o r a n y p a r t t h e r e o f i s p r o h i b i t e d .
I l l u s t r a t i o n s a n
d p h o t o s
m a y s h o w e q u i p m e n t w
i t h o p t i o n a l e x t r a s .
N o w a r r a n t y i s m a d e r e g a r d i n g s p e c i fi c a t i o n s o r o t h e r w i s e .
S p e c i fi c a t i o n s a n d e q u i p m e n t a r e s u b j e c t t o c h a n g e w i t h o
u t n o t i c e .
C o n s u l t y o u r A t l a s C o p c o C u s t o m e r C e n t e r f o r s p e c i fi c i n f o
r m a t i o n .
Measurements
COVERAGE AREA
SIDE VIEW
DIMENSIONS
mm Width 1 950
Height tramming 3 180
Height roof up 2 960
Length tramming (with BHM 234) 8 362
Ground clearance 280
WEIGHT
gross weight
kg Total (basic rig+RHS) 15 500
Boom side 11 000
Engine side 4 500
RECOMMENDED CABLE SIZE AND LENGTH
Voltage Type Dimension, mm2 Diameter,
mm
Length,
m
EDS 18
380–400 V RDOT 4x50 mm2 44 mm 65 m
380–400 V Buflex 3x70+3G16 mm2 37 mm 95 m
440–575 V RDOT 4x35 mm2 38 mm 95 m
440–575 V Buflex 3x50+3G10 mm2 32 mm 140 m
660–700 V RDOT 4x25 mm2 34 mm 115 m
660–700 V Buflex 3x35+3G6 mm2 28 mm 185 m
1 000 V Buflex 3x35+3G6 mm2 28 mm 185 m
G = Protection yellow/green Recommendations are given for surrounding temperature of 40 °C.
TURNING RADIUS
depending on surface
mm Outer 5 440
Inner 2 890
7 0 0
1 8 4 5
2 2 6 0
3 1 8 0
2310150015552304
8763 (with BMH 264)
20º65º
2 5 5
45º
750750
2380
2430
1950
1500
2 0 0 0
45º
9 4 5
1 1 5 0