Shell to Tube Heat Exchanger
-
Upload
dhairya1725 -
Category
Documents
-
view
272 -
download
1
Transcript of Shell to Tube Heat Exchanger
-
7/28/2019 Shell to Tube Heat Exchanger
1/10
SHELL TO TUBE HEAT EXCHANGER
STUDENT NAME : HITESH B PARMAR
COURSE CODE : BMEP-001
PROGRAM CODE : BTME
ENROLMENT NO : 100005965
STUDY CENTER : 0974p
RESIDENT/
CORRESPONDS
ADDRESS : 231 SAHAKAR NAGAR,
NEAR SWATI SOCI,
NEW SAMA ROAD,
VADODARA -390008
E-mail id:[email protected]
CONTACT NO : 9727072675
mailto:[email protected]:[email protected]:[email protected]:[email protected] -
7/28/2019 Shell to Tube Heat Exchanger
2/10
1)TITLE OF PROJECT:-TO STUDY SHELL TO TUBE HEAT EXCHANGER
2)OBJECTIVE OF STUDY:-A drum used to transfer orexchange heat is known as heat exchanger.
A shell and tube heat exchanger is a class of heat exchanger designs It is the mostcommon type of heat exchanger in oil refineries and other large chemical
processes and is suited for a higherpressure application. As its name implies this
type of heat exchangers consist of a shell (a large pressure vessel) with the bundle
of tubes inside it one fuel runs through the tubes and the flows over the tubes
(through the shell) to transfer the between the two fuels. The set of tubes is called
a tube bundle may be and may be composed by several types of tubes plain
longitudinally finned etc.
Surface condenses is the commonly used term for a water cooled shell and tubeheat exchanger installed on the exhaust steam from a steam turbine in thermal
power station.
In a thermal power plant the primary purpose of is a to condense the exhauststeam from a steam turbine to obtain maximum efficiency and also to convert the
turbine exhaust steam into pure water (referred to as a steam condenset). So that it
may be reused in the steam generator or boiler as boiler feed water.
Shell and tube heat exchanger is a class of heat exchanges design most commontype of heat exchanger in oil refineries in other chemical process.
IInn ttooddaayyss mmooddeerrnn wwoorrlldd,, iitt iiss pprriimmaarryy nneeeedd ffoorr PPeettrrooll,, DDiieesseell && vvaarriioouuss ppeettrroocchheemmiiccaall
pprroodduuccttss.. IItt iiss ddiiffffiiccuulltt ttoo tthhiinnkk ooff lliiffee wwiitthhoouutt ppeettrroocchheemmiiccaall pprroodduuccttss.. TThheessee pprroodduuccttss rreeaacchheess
ppaassssiinngg tthhrroouugghh rreeffiinneerriieess && ppeettrroocchheemmiiccaall ppllaannttss aafftteerrvvaarriioouuss pprroocceesssseess..
IItt mmeeaannss,, tthhee pprroocceessss iinndduussttrriieess bbeeccoommeess tthhee pprriimmaarryy rreeqquuiirreemmeennttss.. TThheessee pprroocceessss
iinndduussttrriieess ((ee..gg.. RReeffiinneerriieess,, ccrraacckkeerrppllaannttss,, hhyyddrrooccaarrbboonn pprroodduucctt pprroocceessssiinngg)) uussee HHeeaatt eexxcchhaannggeerr
..HHeeaatt eexxcchhaannggeerriiss ggoooodd ttrraannssffeerrrriinngg hheeaatt oonnee lliiqquuiidd ttoo ootthheerrlliiqquuiidd aatt vvaarriioouuss tteemmppeerraattuurreess..
HHeeaatt eexxcchhaannggeerr iiss uusseedd ttoo ccoonnttaaiinn aa mmuullttiippllee tthhiinngg iinncclluuddiinngg aaiirr,, wwaatteerr,, cchheemmiiccaallss,, aanndd
ffuueell.. TThheeyy aarree uusseedd iinn ppaappeerraanndd ppuullpp,, eenneerrggyy,, ffoooodd,, cchheemmiiccaall iinndduussttrriieess..
HHeeaatt eexxcchhaannggeerriiss ddeessiiggnneedd wwiitthh ggrreeaatt ccaarree bbeeccaauussee rraappttuurree ooffaa HHeeaatt eexxcchhaannggeerrmmeeaannss aann
eexxpplloossiioonn wwhhiicchh mmaayy ccaauussee lloossss oofflliiffee aanndd pprrooppeerrttyy..
DDeeffiinniittiioonn ooffhheeaatt eexxcchhaannggeerr::--
-
7/28/2019 Shell to Tube Heat Exchanger
3/10
-
7/28/2019 Shell to Tube Heat Exchanger
4/10
-
7/28/2019 Shell to Tube Heat Exchanger
5/10
ppiicckkss uupp hheeaatt aanndd eevveennttuuaallllyy ggeettss ccoonnvveerrtteedd ttoo sstteeaamm..
TThhee SShheellll aanndd TTuubbee iiss tthhee mmoosstt ccoommmmoonn ttyyppee ooff hheeaatt eexxcchhaannggeerr uusseedd iinn tthhee pprroocceessss,,
ppeettrroolleeuumm,, cchheemmiiccaall iinndduussttrriieess,, iitt ccoonnttaaiinnss aa nnuummbbeerrooffppaarraalllleell uuttuubbeess iinnssiiddee aa sshheellll.. SShheellll TTuubbeehheeaatt eexxcchhaannggeerrss aarree uusseedd wwhheenn aa pprroocceessss rreeqquuiirreess llaarrggee aammoouunnttss oofffflluuiidd ttoo bbee hheeaatteedd oorrccoooolleedd..
DDuuee ttoo tthheeiirrddeessiiggnn,, sshheellll ttuubbee hheeaatt eexxcchhaannggeerrss ooffffeerraa llaarrggee hheeaatt ttrraannssffeerraarreeaa aanndd pprroovviiddee hhiigghh
hheeaatt ttrraannssffeerreeffffiicciieennccyy.. DDEESSIIGGNN PPAARRAAMMEETTEERRSS OOFF HHEEAATT EEXXCCHHAANNGGEERR::--
-
7/28/2019 Shell to Tube Heat Exchanger
6/10
-
7/28/2019 Shell to Tube Heat Exchanger
7/10
TThhee mmaannuuffaaccttuurriinngg sseeqquueenncceess aarree ssiimmiillaarrlliikkee ssiinnggllee wwaallll vveesssseell wwiitthh aa ddiiffffeerreennccee ooffeexxttrraa
ccaarree dduurriinngg rroolllliinngg ooffccllaadd ppllaattee hhaavviinngg SSSS bbuuffffeedd ssuurrffaaccee iinnssiiddee..AAnnootthheerrooppttiioonn ffoorrssuucchh ccoorrrroossiivvee sseerrvviicceess iiss ccaarrrryyiinngg oouutt SSttaaiinnlleessss SStteeeell oovveerrllaayy iinnssiiddee tthhee AAllllooyy
sstteeeell sshheellll aafftteerrrroolllliinngg ttoo rreeqquuiirreedd ddiiaammeetteerr..
TThhiiss iiss mmoorree ttiimmee ccoonnssuummiinngg mmeetthhoodd aass iitt rreeqquuiirreess ggeenneerraattiioonn ooffaa ccoommpplleettee llaayyeerrooffSSSS iinnssiiddeesshheellll.. OOnn tthhee ootthheerrhhaanndd,, tthhiiss mmuucchh cchheeaappeerrtthhaann CCllaadd VVeesssseellss.. OOvveerrllaayyeedd vveesssseellss aarree nnooww--aa--ddaayyss
pprreeffeerrrreedd mmuucchh oovveerrccllaadd vveesssseell bbyy MMooddeerrnn PPrroocceessss LLiicceennssoorrss lliikkee IIFFPP..
3) OPERATIONAL METHODOLOGY OF SHELL TO TUBE HEAT
EXCHANGER:-
Shell and tube heat exchanger is a class of heat exchanges design most commontype of heat exchanger in oil refineries in other chemical process.
Two type of heat exchanger in shell and tube heat exchanger one phase (liquid orgas) on each side can be called one - phase or single - phase heat exchanger. Two
phase heat exchanger can be used to heat exchanger liquid to boil it into a gas
(vapor) some times called a boiler or cooled a vapor to condense it into a liquid
(called condenser).
With the phase changes usually occurring on the shell side boiler in steam enginelocomotive are typically large, usually cylindrically shell and tube heat exchanger.
In the large power plants with steam driven turbines, shellandtube surface
condenser are used to condense the exhaust steam exiting the turbine into
condensate water which is recycle back to me turned into steam in the steam
generator.
Heat exchanger is suited in higher application in industries. This type of heatexchanger consist of a shell (a large pressure vessel) with a bundle of tube inside
it one fluids runs through the tubes and the other fluids flows over the tubes
(through the shell) to transfer heat between the two fluids. The set of tubes is
called a tube bundle and may be composed by a several types of tubes, plain
longitudinally finned etc.
Its used in large chemical processes, thermal power station and oil and gasrefineries.
Our project made by help organizational help of supervisor internet for refreshmatter.
Additional reference: Book of thermal engineering & panchal C; B & embertanalysis of Exxon crude-oil-slipstream enclosing data proc of fouling mitigation
of industrial heat exchanger equipment, San Luis Obispo, California USA in1995.
-
7/28/2019 Shell to Tube Heat Exchanger
8/10
A drum used to transform or exchange heat is known as heat exchanger. Shell & tube heat exchanger widely used in industry both for cooling &
heating large scale industrial processes. In thermal power plants the primary
purpose of airs to condense the exhaust steam from a steam turbine to obtain
maximum efficiency and also to convert the turbine exhaust steam into purewater ( referred to as steam condensate) so that it may be reused in the steam
generator or boiler as boiler feed water.
Methodology for heat exchanger is as below Plate identification & material identification. Plate marking operation done and edge breaking and pre-punching
operation done.
Groove is made on plat as per drawing then the plate is to be rolled onrolling machine as per requirement.
Then plate rolled and welds tacking then welding done on roll platethis is called shell.
Then one & different shell made it & jointed through smaw and sawwelding and creating the c seam welding.
Then as per drawing nozzle set up tube sheet marking (in a plant anddrilling as per drawing. Then its set up is done with shell (the groove
of tube sheet and shell is made earlier). Now is welding is carried out
& tube insertion log attach sliding saddle has been done by welding
and then job is going to in blasting and then job is go to painting and
then job is ready.
3) THE EXPECTED CONTRIBUTION FROM THE STUDY:- Our project guide Haresh sir guided how to make a heat exchanger. He gives the
information about fabrication sequences, material selection, planning and organization
ISO standerd and ASME code welding to other documentary work has been done in
production in Akshar engineering works. So we would include whole fabricationsequences in the Akshar engineering works.
Other information we are collecting on internet and other reference bookas a thermal engineering material logy.
Use organization help of supervisor or internet references.
-
7/28/2019 Shell to Tube Heat Exchanger
9/10
4) LIST OF ACTIVITIES TO CARRIED OUT TO COMPLETE THE PROJECT:-(WITH THE HELP OF BAR CHART SHOWING THE TIME SCHEDULE)
PROJECT TIME DURATION
0 5 10 15 20 25 30 35
DAYS
INTRODUCTION BASIC INFORMATION
DETAILS OF SHELL AND TUBE HEAT EXCHANGER
DEVELOP DRAWING AND BOM
GENERAL CONSTRUCTION AND WORKING
CLASSIFICATION & WORKING
HYDROTEST BLASTING AND PAINTING
PROJECT COMPLETION
Series1
Series2
PROJECT TIME DURATION
Days INTRODUCTION
BASIC
INFORMATION
DETAILS OF
SHELL AND
TUBE HEATEXCHANGER
DEVELOP
DRAWING
AND BOM
GENERAL
CONSTRUCTION
AND WORKING
CLASSIFI
& WOR
-
7/28/2019 Shell to Tube Heat Exchanger
10/10
Series 1 5 10 15 20
5) PLACES/LABS/EQUIPMENTS & TOOLS REQUIRED & PLANNING OFARRANGEMENTS:
Place:-
1) Akshar engineering works savli, Baroda.
2) WORKSHOPE, FISICAS LAB
6) LABS/EQUIPMENTS:- Computers centre, library, TUBE SHEET 230 OD * 10 THK, SA 516 GR 70 MTR 2 QTY, SHELL 219 OD * 7 THK * 470 L, MTR SA 106 GR B 1 QTY, LUG PLATE 80 * 90 * 10THK, SA 516 gr 70- 2 QTY, PLATE 80 OD *10 THK, SA 516 gr 70 meter 2 QTY, TUBE OD 31.8 * 6.35 THK * 60 L, MTR SA 210 GR A1 2 QTY, TUBE OD 31.8 * 6.35 THK * 35, MTR SA 210 GR A1 2 QTY, TUBE OD 31.8 * 6.35 THK * 496, MTR SA 210 GR A1 16 QTY, PLATE 190 * 100 * 10 SA 515 GR 70 2 QTY, PLATE 190 * 130 * 10 SA 515 GR 70 2 QTY.
7) PLANNER:-AS PLANNED BY SUPARVISOR AND COORDINATORS & GUIDE HELP
8) PROBLEMS ENVISAGED IN CARRYING OUT THE PROJECT, IF ANYNIL