INS

TRU

CTIO

NM

AN

UA

LSharpening Center

(Model 23-710)

PART NO. 1346949 - 05-14-04Copyright © 2004 Delta Machinery

To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.For Parts, Service, Warranty or other Assistance,

please call 1-800-223-7278 (In Canada call 1-800-463-3582).

62079

RTD10000127AA

2

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, mayresult in property damage.

This manual contains information that is important for you to know and understand. This information relates to protect-ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use thesymbols below. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES - DEFINITIONS

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHERCONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.Some examples of these chemicals are:· lead from lead-based paints,· crystalline silica from bricks and cement and other masonry products, and· arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure tothese chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSHapproved, properly fitting face mask or respirator when using such tools.

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with the operation of the product. Using the machine with respect and caution willconsiderably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t makeup for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Yourpersonal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.

This machine was designed for certain applications only. Delta Machinery strongly recommends that thismachine not be modified and/or used for any application other than that for which it was designed. If you have anyquestions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determineif it can or should be performed on the product.

Technical Service ManagerDelta Machinery4825 Highway 45 NorthJackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

3

GENERAL SAFETY RULES

1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE.Learning the machine’s application, limitations, andspecific hazards will greatly minimize the possibility ofaccidents and injury.

2. WEAR EYE PROTECTION. ALWAYS USE SAFETYGLASSES. Also use face or dust mask if cuttingoperation is dusty. Everyday eyeglasses are NOT safetyglasses. USE CERTIFIED SAFETY EQUIPMENT. Eyeprotection equipment should comply with ANSI Z87.1standards, hearing equipment should comply withANSI S3.19 standards, and dust mask protectionshould comply with MSHA/NIOSH certified respiratorstandards. Splinters, air-borne debris, and dust cancause irritation, injury, and/or illness.

3. WEAR PROPER APPAREL. Do not wear looseclothing, gloves, neckties, rings, bracelets, or otherjewelry which may get caught in moving parts. Nonslipfootwear is recommended. Wear protective haircovering to contain long hair.

4. DO NOT USE THE MACHINE IN A DANGEROUSENVIRONMENT. The use of power tools in damp orwet locations or in rain can cause shock orelectrocution. Keep your work area well-lit to preventtripping or placing arms, hands, and fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAKCONDITION. Keep tools sharp and clean for best and safestperformance. Follow instructions for lubricating and changingaccessories. Poorly maintained tools and machines can furtherdamage the tool or machine and/or cause injury.

6. CHECK FOR DAMAGED PARTS. Before using themachine, check for any damaged parts. Check foralignment of moving parts, binding of moving parts,breakage of parts, and any other conditions that mayaffect its operation. A guard or any other part that isdamaged should be properly repaired or replaced.Damaged parts can cause further damage to themachine and/or injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas andbenches invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is apotentially dangerous environment. Children and visitors canbe injured.

9. REDUCE THE RISK OF UNINTENTIONAL STARTING.Make sure that the switch is in the “OFF” positionbefore plugging in the power cord. In the event of apower failure, move the switch to the “OFF” position.An accidental start-up can cause injury.

10. USE THE GUARDS. Check to see that all guards are inplace, secured, and working correctly to prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHESBEFORE STARTING THE MACHINE. Tools, scrappieces, and other debris can be thrown at high speed,causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine oran attachment to do a job for which it was not

designed. Damage to the machine and/or injury mayresult.

13. USE RECOMMENDED ACCESSORIES. The use ofaccessories and attachments not recommended byDelta may cause damage to the machine or injury tothe user.

14. USE THE PROPER EXTENSION CORD. Make sureyour extension cord is in good condition. When usingan extension cord, be sure to use one heavy enoughto carry the current your product will draw. Anundersized cord will cause a drop in line voltage,resulting in loss of power and overheating. See theExtension Cord Chart for the correct size dependingon the cord length and nameplate ampere rating. If indoubt, use the next heavier gauge. The smaller thegauge number, the heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise tohold the workpiece when practical. Loss of control ofa workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OFTHE ROTATION OF THE BLADE, CUTTER, ORABRASIVE SURFACE. Feeding it from the otherdirection will cause the workpiece to be thrown out athigh speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make youfall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur ifthe tool tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNINGUNATTENDED. TURN THE POWER OFF. Don’t leave themachine until it comes to a complete stop. A child or visitorcould be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THEMACHINE FROM THE POWER SOURCE beforeinstalling or removing accessories, before adjustingor changing set-ups, or when making repairs. Anaccidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITHPADLOCKS, MASTER SWITCHES, OR BYREMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could causeinjury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING,AND USE COMMON SENSE. DO NOT USE THEMACHINE WHEN YOU ARE TIRED OR UNDERTHE INFLUENCE OF DRUGS, ALCOHOL, ORMEDICATION. A moment of inattention whileoperating power tools may result in injury.

24. TAKE PRECAUTIONS AGAINST DUSTINHALATION. The dust generated by certain woodsand wood products can be injurious to your health.Always operate machinery in well-ventilated areas,and provide for proper dust removal. Use wood dustcollection systems whenever possible.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

4

ADDITIONAL SAFETY RULES FOR SHARPENING CENTERS

1. DO NOT OPERATE THIS MACHINE until it iscompletely assembled and installed according to theinstructions. A machine incorrectly assembled cancause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor, oranother qualified person if you are not thoroughlyfamiliar with the operation of this machine. Knowledgeis safety.

3. FOLLOW ALL WIRING CODES and recommendedelectrical connections to prevent shock orelectrocution.

4. ALWAYS USE THE PROVIDED BLOTTER ANDWHEEL FLANGES to mount the grinding wheels onthe grinder shaft to prevent wheel damge or acciden-tal separation. Separation can result in fragmentsflying off the wheel at high speeds.

5. USE ONLY WHEELS suitable for the speed of themachine. Unsuitable grinding wheels can come apart,throwing fragments out at high speeds.

6. USE ONLY WHEELS that have a bore exactly equalto the arbors of the machine. Never attempt tomachine an undersized wheel to fit an arbor.Unsuitable grinding wheels can come apart, throwingfragments out at high speeds.

7. DO NOT OVERTIGHTEN WHEEL NUT.8. DO NOT USE A WHEEL THAT VIBRATES. Dress the

grinding wheel, replace it, or replace the bearings ofthe shaft. Unsuitable grinding wheels can come apart,throwing fragments at high speeds.

9. INSPECT WHEELS before starting the machine forcracks or fragments. REPLACE DAMAGED WHEELSimmediately. Parts of the wheel can be thrown at highspeeds causing serious injury.

10. ADJUST EYE SHIELDS close to the grinding wheel,and re-adjust as the wheel wears down. Flying sparksare dangerous and can cause fires or explosions.

11. ALWAYS MAKE SURE the eye shields are in place,properly adjusted, and secured.

12. ADJUST TOOL RESTS close to the grinding wheel(1/8" separation or less). Tighten the tool rest securelyto prevent shifting positions, and re-adjust as thewheel wears down. The workpiece can be drawn intothe wheel, causing damage to the workpiece and/orserious injury.

13. STAND TO ONE SIDE before turning the machine“ON”. Loose fragments or wheel parts could fly fromthe wheel at high speeds.

14. NEVER GRIND ON A COLD WHEEL. Run the grinderfor one full minute before applying the workpiece. Acold wheel has a tendency to chip. Those fragmentscould fly from the wheel at high speeds.

15. NEVER START THE MACHINE with the workpieceagainst the grinding wheel. The workpiece can bedrawn into the wheel, causing damage to the machine

and/or serious injury.16. CLEAN THE MACHINE thoroughly when processing

different types of workpieces (wood, steel, oraluminum). Combining wood and metal dust cancreate an explosion or fire hazard. DO NOT GRINDOR POLISH MAGNESIUM. Fire will result.

17. NEVER GRIND NEAR FLAMMABLE GAS ORLIQUIDS. Sparks can create a fire or an explosion.

18. AVOID AWKWARD OPERATIONS AND HANDPOSITIONS. A sudden slip could cause a hand tomove into the grinding wheel.

19. KEEP ARMS, HANDS, AND FINGERS away from thewheel. The abrasive surfaces can cause serious injury.

20. HOLD THE WORKPIECE FIRMLY against the toolrest. Loss of control of the workpiece can causeserious injury.

21. DRESS THE WHEEL on the face only. Dressing theside of the wheel could cause it to become too thinfor safe use.

22. GRIND A WORKPIECE using the face of the grindingwheel only. Loss of control of the workpiece cancause serious injury.

23. NEVER APPLY COOLANT directly to the grindingwheel. Coolant can weaken the bonding strength ofthe grinding wheel and cause it to fail. Dip theworkpiece in water to cool it.

24. DO NOT TOUCH the ground portion of a workpieceuntil it has cooled sufficiently. Grinding creates heat.

25. PROPERLY SUPPORT LONG OR WIDE WORK-PIECES. Loss of control of the workpiece can causeserious injury.

26. NEVER PERFORM LAYOUT, ASSEMBLY, or set-upwork on the table/work area when the machine isrunning. A sudden slip could cause a hand to moveinto the wheel. Severe injury can result.

27. TURN THE MACHINE “OFF”, disconnect themachine from the power source, and clean thetable/work area before leaving the machine. LOCKTHE SWITCH IN THE “OFF” POSITION to preventunauthorized use. Someone else might accidentallystart the machine and cause serious injury tothemselves.

28. ADDITIONAL INFORMATION regarding the safeand proper operation of power tools (i.e. a safetyvideo) is available from the Power Tool Institute, 1300Sumner Avenue, Cleveland, OH 44115-2851(www.powertoolinstitute.com). Information is alsoavailable from the National Safety Council, 1121Spring Lake Drive, Itasca, IL 60143-3201. Pleaserefer to the American National Standards InstituteANSI 01.1 Safety Requirements for WoodworkingMachines and the U.S. Department of Labor OSHA1910.213 Regulations.

SAVE THESE INSTRUCTIONS. Refer to them often

and use them to instruct others.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

5

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting themachine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is ofthe same characteristics as indicated on the machine. All line connections should make good contact. Running on lowvoltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

Fig. A Fig. B

GROUNDED OUTLET BOX

CURRENTCARRYING

PRONGS

GROUNDING BLADEIS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDINGMEANS

ADAPTER

2. Grounded, cord-connected machines intended for useon a supply circuit having a nominal rating less than 150volts:

If the machine is intended for use on a circuit that has anoutlet that looks like the one illustrated in Fig. A, themachine will have a grounding plug that looks like the plugillustrated in Fig. A. A temporary adapter, which looks likethe adapter illustrated in Fig. B, may be used to connectthis plug to a matching 2-conductor receptacle as shownin Fig. B if a properly grounded outlet is not available. Thetemporary adapter should be used only until a properlygrounded outlet can be installed by a qualified electrician.The green-colored rigid ear, lug, and the like, extendingfrom the adapter must be connected to a permanentground such as a properly grounded outlet box. Wheneverthe adapter is used, it must be held in place with a metalscrew.

NOTE: In Canada, the use of a temporary adapter is notpermitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THER E C E P TA C L E I N Q U E S T I O N I S P R O P E R LYGROUNDED. IF YOU ARE NOT SURE HAVE AQUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, groundingprovides a path of least resistance for electric current toreduce the risk of electric shock. This machine isequipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug mustbe plugged into a matching outlet that is properly installedand grounded in accordance with all local codes andordinances.

Do not modify the plug provided - if it will not fit the outlet,have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-groundingconductor can result in risk of electric shock. Theconductor with insulation having an outer surface that isgreen with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of theelectric cord or plug is necessary, do not connect theequipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel ifthe grounding inst ruct ions are not complete lyunderstood, or if in doubt as to whether the machine isproperly grounded.

Use only 3-wire extension cords that have 3-pronggrounding type plugs and matching 3-conductorreceptacles that accept the machine’s plug, as shown inFig. A.

Repair or replace damaged or worn cord immediately.

POWER CONNECTIONS

MOTOR SPECIFICATIONSYour machine is wired for 120 volts 60 HZ alternating current. Before connecting the machine to the power source,make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONSTHIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROMELECTRIC SHOCK.

6

EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wire

extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’splug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. Anundersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, showsthe correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gaugenumber, the heavier the cord.

Fig. D-1 Fig. D-2

MINIMUM GAUGE EXTENSION CORDRECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge ofRating Volts of Cord in Feet Extension Cord

0-6 120 up to 25 18 AWG0-6 120 25-50 16 AWG0-6 120 50-100 16 AWG0-6 120 100-150 14 AWG

6-10 120 up to 25 18 AWG6-10 120 25-50 16 AWG6-10 120 50-100 14 AWG6-10 120 100-150 12 AWG

10-12 120 up to 25 16 AWG10-12 120 25-50 16 AWG10-12 120 50-100 14 AWG10-12 120 100-150 12 AWG

12-16 120 up to 25 14 AWG12-16 120 25-50 12 AWG12-16 120 GREATER THAN 50 FEET NOT RECOMMENDED

MINIMUM GAUGE EXTENSION CORDRECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge ofRating Volts of Cord in Feet Extension Cord

0-6 240 up to 50 18 AWG0-6 240 50-100 16 AWG0-6 240 100-200 16 AWG0-6 240 200-300 14 AWG

6-10 240 up to 50 18 AWG6-10 240 50-100 16 AWG6-10 240 100-200 14 AWG6-10 240 200-300 12 AWG

10-12 240 up to 50 16 AWG10-12 240 50-100 16 AWG10-12 240 100-200 14 AWG10-12 240 200-300 12 AWG

12-16 240 up to 50 14 AWG12-16 240 50-100 12 AWG12-16 240 GREATER THAN 100 FEET NOT RECOMMENDED

FOREWORD

FUNCTIONAL DESCRIPTION

The Delta Industrial Sharpening Center Model 23-710 has a 1/5 HP motor. It also comes with a 5” diameter, 120 gritaluminum oxide dry wheel, an 8” diameter, 1000-grit wet wheel, a tool rest and base, a sliding tool holder, a water tank,eye shield and wrenches.

7

UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality householdfloor paste wax.

NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THECURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS CONTAINEDIN THE MANUAL ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THEACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TOILLUSTRATE TECHNIQUE ONLY.

Fig. 2

2

1. Sharpening Center2. Water Tank3. Tool and Chisel Holder4. Wheel Dressing Stone5. Tool and Chisel Holder Base Assembly6. Tilting Screw and Spring for Tool and Chisel Holder

w/(2) Flat Washers7. 6mm Allen wrench8. 6mm Allen Wrench9. Wrench10. Tool Rest for Dry Wheel11. Flat Washer

12. Lockwasher13. 5/8” Long Hex Head Screw14. Eyeshield Clamp Bracket15. Eyeshield Mounting Rod16. Eyeshield Lock Knob17. 3/4” Long Carriage Head Bolt18. 1/4-20 Hex Nut19. Eyeshield Frame20. 1/2” Long, Round Head Screw (2)21. Flat Washer (2)22. #10-24 Hex Nut (2)23. Eyeshield

1

8

9

3

4131211

10

14

1516

17

18

2322

19 2021

5

7

6

8

ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT MACHINE TO THE POWER SOURCE UNTIL THEMACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND UNDERSTAND THE ENTIRE

INSTRUCTION MANUAL.

Fig. 3

ASSEMBLING ANDADJUSTING EYESHIELD

1. Position eyeshield (A) Fig. 3, under lip of frame (B).Line up holes in eyeshield (A) with holes in frame (B)and fasten eyeshield to frame using two 1/2” longround head screws (C), flat washers (D) and hex nuts(E). Place flat washer on round head screw, placescrew through hole and then fasten hex nut to screwunder the frame.

2. Insert short end of eyeshield mounting rod (F) Fig. 4,into top of frame (B) and fasten in place with the 3/4”long carriage head bolt (G) and hex nut (H).

3. Figure 5, illustrates the mounting rod (F), frame (B)and eyeshield (A) assembled.

4. Assemble the long end of eyeshield mounting rod (F)Fig. 6, to the side of the dry wheel guard using clampbracket (J) and lock knob (K). The eyeshield (A) isfully adjustable to any position by moving shield (A)or loosening lock knob (K) and repositioningmounting rod (F).

G

H

B

F

D

E E

D

A

C

B

F

A

Fig. 4

Fig. 5

Fig. 6

A

B

C

K

J

F

9

ASSEMBLING ANDADJUSTING TOOL RESTFOR DRY WHEEL

1. Assemble dry wheel tool rest (A) Fig. 7, to mountingarm (B) using flat washer (C), lockwasher (D) and5/8” long hex head screw (E). Place a lockwasherthen a flat washer on the hex head screw, thenassemble tool rest to mounting arm as shown in Fig.8.

WRENCH HOLDING BRACKET

1. Wrench (D) Fig. 10, can be stored in bracket (A)when not in use.

2. Figure 8, illustrates dry wheel tool rest (A) assembledto mounting arm (B). Wrench (F) supplied, is used totighten screw (E).

3. The tool rest (A) Fig. 8, is adjustable so the insideedge of the tool rest can be positioned as close tothe grinding wheel (H) as possible, giving maximumsupport to the piece that is being ground. Alwaysmaintain a distance of 1/8” or less between thegrinding wheel (H) and inside edge of tool rest (A). Asthe grinding wheel wears down to a smallerdiameter, readjust the tool rest closer to the wheel byloosening screw (E), moving tool rest (A) inward andtightening screw (E) using wrench (F). The tool rest(A) can also be rotated to any desired angle byloosening screw (E), rotating tool rest (A) andtightening screw. Rotate dry wheel (H) makingcertain wheel does not contact tool rest (A).

A

D

A

CD E

F

Fig. 7

Fig. 8

Fig. 10

B

H

B

E

A

10

1. Take the tool and chisel holder base and insert itsmounting post (A) Fig. 11, into hole (B) in the front ofthe machine, and tighten screw (C) against groove(E) of mounting post. Use the provided wrench (D)Fig. 10.

ASSEMBLING AND ADJUSTINGTOOL AND CHISEL HOLDER

Fig. 13

Fig. 14

2. Loosen screw (C) Fig. 13, move tool and chiselholder to desired position and tighten screw (C).

3. Place flat washer, spring and another flat washeronto the tilting screw knob. Thread tilting screw andspring assembly (H) Fig. 13, into hole in post. NOTE:End of screw (H) contacts lever (R) and this screw isused to tilt the tool rest base (J).

4. To level tool and chisel holder base (J) Fig. 13, withthe set grinding wheel (G), loosen screw (F) withsupplied wrench, and turn complete base assembly(E) until tool and chisel holder base (J) is level withwet grinding wheel (G), and tighten screw (F).

5. To adjust the height of tool and chisel holder baseassembly (E) Fig. 14, loosen screw (S) and turn ad-justment knob (T). Tighten screw (S) after heightadjustment is made.

J

CA

E

F

GH

R

S

E

T

Fig. 11

B

C

A

E

11

ASSEMBLING AND ADJUSTINGWATER TANK

1. Insert stem (A) Fig. 18, of water tank (B) into holder(C) as shown.

Fig. 15

7. Fig. 16, illustrates tool and chisel holder (K) inposition on tool rest base (J).

8. To raise or lower the tool and chisel holder assembly(E) Fig. 17, refer to STEP 5.

9. To tilt the tool and chisel holder (J) Fig.17, to conformwith the angle of the tool to be sharpened, loosen setscrew (N) and turn knob (H) as necessary. After angleis set, tighten set screw (N).

10. To move the tool and chisel holder (J) Fig. 17, in orout, loosen set screw (C), and slide assembly (E) inor out as desired. After adjustment, tighten screw(C).

11. To level tool and chisel holder base (J) Fig. 17, withthe wet grinding wheel (G), loosen screw (F) withsupplied wrench, and rotate complete baseassembly (E) until tool and chisel holder base (J) islevel with wet grinding wheel (G), and tighten screw(F).

Fig. 16

Fig. 17

Fig. 18

6. Place tool and chisel holder (K) Fig. 15, in position onbase (J).

C

K

JK

J

N

H

E

F

GJ

BAC

12

Fig. 19

Fig. 20

Fig. 21

2. The water tank (B) Fig. 19, can be rotated to directthe water from the spigot (D) onto the grinding wheel.The ideal position of the spigot (D) would be to thecenter (C) of the grinding wheel.

3. To control the flow of water from the spigot (D) Fig.19, turn knob (E).

4. A drain (F) Fig. 20, is provided underneath thegrinding wheel housing to dispose of water. Place acan or suitable container underneath the drain (F).

FASTENING SHARPENING CENTERTO SUPPORTING SURFACE

If during operation there is any tendency for the machineto tip over, slide or "walk" on the supporting surface, themachine must be secured to the supporting surface. Twoholes, (A) Fig. 9, are provided for this purpose.

AA

B

D

E

F

C

13

Fig. 25

1. Loosen the two clamp knobs (A) Figs. 25, 26 and 27,and insert the tool or chisel between the clamp asshown, making sure the edge of the tool or chisel isagainst the inside of the protractor gage (B). Fig. 25illustrates a plane iron; Fig. 26 illustrates a woodchisel; and Fig. 27 illustrates a lathe turning toolinserted between the clamp of the tool and chiselholder. Then tighten the two clamp knobs (A). Adjustthe protractor gage (B) so that the cutting edge ofthe tool to be sharpened is the correct angle for thegrinding wheel. Loosen screw (C) Fig. 27, and adjustthe protractor gage (B) as shown. Tighten screw (C)after angle is obtained.

The tool and chisel holder is supplied as standard equip-ment with your sharpening center and is ideal for sharp-ening wood chisels, plane irons, some lathe turningtools, etc. To use the tool and chisel holder, proceed asfollows.

USING TOOL AND CHISEL HOLDER

Fig. 26

3. Figure 29, illustrates a plane iron being sharpenedusing the tool and chisel holder (D) supplied with themachine.

2. Place the complete tool and chisel holder assembly(D) Fig. 28, on the tool rest base (E) as shown.Adjustment of the tool rest is explained in section“ASSEMBLING AND ADJUSTING TOOL ANDCHISEL HOLDER.”

Fig. 27

Fig. 28

Fig. 29

A

B

B

A

B

A

C

D

D

E

OPERATION

14

Fig. 30

STARTING ANDSTOPPING MACHINE

The switch (A) Fig. 30, is located on the front of thegrinder base inside a water resistant enclosure. To turnthe machine “ON” push the left hand portion of theswitch. To turn the machine “OFF” push the right handportion of the switch.

ADJUSTINGSPLASH GUARDSTwo adjustable splash guards (A) and (B) Fig. 31, are pro-vided with your sharpening center. The height of the frontsplash guard (A) should be adjusted so the top edge ofthe guard (A) is slightly below the grinding surface (C) ofthe wheel. The rear splash guard should be positionedhigh, as shown. To adjust the splash guards, move theguards manually.

Fig. 31

Fig. 32

Fig. 34

USING TOOL AND CHISEL HOLDERON DRY WHEELWhen sharpening chisels, plane irons, etc., that havedeep nicks, the cutting edge of the tool can first be roughground on the dry grinding wheel before fine sharpeningis performed on the wet wheel. To use the tool and chiselholder on the dry wheel, proceed as follows:

1. Remove the dry wheel tool rest (A) Fig. 32, and eye-shield (B).

2. Loosen screw (C) Fig. 33, and rotate wheel guard (D)to the rear, as shown in Fig. 34, and tighten screw(C).

Fig. 33

A

C

C

D

CB

A

B

A

D

15Fig. 39

Fig. 35

Fig. 36

Fig. 37

Fig. 38

3. Remove the tool rest and mounting post (E) Fig. 35,from the wet wheel side of the machine and insertpost of tool rest assembly into hole (F). Tightenscrew (G) into groove of mounting post. All controlsand adjustments for the tool rest are explained in thesection “ASSEMBLING AND ADJUSTING TOOLAND CHISEL HOLDER.”

4. Figure 36, illustrates a rough grinding operation on aplane iron (H) using the dry wheel.

ASSEMBLING OPTIONALACCESSORY 23-715 SLIDING TOOLREST TO WET WHEEL

The 23-715 Sliding Tool Rest is available as an accessoryfor your sharpening center and is especially suited forsharpening jointer and planer knives. To assemble the23-715 Sliding Tool Rest, proceed as follows:

1. Loosen screw (A) Fig. 37, and remove tool and chiselholder assembly (B) as shown.

2. Assemble sliding table tool rest base (E) Fig. 38, tomounting post (A) and tighten screw (F) againstgroove (G) in mounting post.

3. Place flat washer, spring and another flat washeronto the tilting screw knob included with the 23-715.Thread tilting screw and spring assembly (H) Fig. 39,into hole in left post.

H

E

F

G

A

H

J

E

F

G

B

A

16

Fig. 40

Fig. 41

Fig. 42

Fig. 43

5. Fig. 41, illustrates sliding tool rest (K) in position ontool rest base (J).

4. Place sliding tool rest (K) Fig. 40, in position on base(J).

Fig. 44

6. To level sliding tool rest (K) Fig. 42, with the wetgrinding wheel, loosen screw (L), rotate completetool rest base (E) right or left until tool rest (K) is levelwith the wet grinding wheel and tighten screw (L).

7. To raise sliding tool rest (K) Fig. 43, unlock two posts(M) by moving clamp lever (N) to the right, as shown.Rotate knob (O) Fig. 44, clockwise to raise, orcounterclockwise to lower the tool rest (K). After theheight of tool rest (K) is set, move clamp lever (N) tothe left in the locked position.

K

J

K

J

K

E

LK

N

M

K

N

O

17

2. Loosen screw (C) Fig. 47, and rotate wheel guard (D)to the rear, as shown in Fig. 48, and tighten screw(C).

Fig. 45

Fig. 46

8. To tilt the sliding tool rest (K) Fig. 45, to conform withthe angle of the knife to be sharpened, turn the toolrest tilting knob (P).

USING ACCESSORY 23-715 SLIDINGTOOL REST ON DRY WHEEL

When sharpening planer or jointer knives that have deepnicks, the knives can first be rough ground on the drygrinding wheel, using the sliding tool rest, before finesharpening is performed on the wet wheel. To use thesliding tool rest on the dry wheel, proceed as follows:

1. Remove the dry wheel tool rest (A) Fig. 46, andeyeshield (B).

Fig. 47

Fig. 48

B

C

C

D

P

K

A

D

18

Fig. 49 Fig. 50

Fig. 51

Fig. 52

3. Remove sliding tool rest and mounting post (E) Fig.49, from the wet wheel side of the machine andinsert post of tool rest assembly into hole (F). Tightenscrew (G) into groove (J) of mounting post (E).

4. Fig. 50, illustrates the sliding tool rest (E) assembledto the dry wheel side of the machine with the knifeholder (H) positioned on the tool rest. All controlsand adjustments for the sliding tool rest areexplained in the section of this manual titled“ASSEMBLING ACCESSORY 23-715 SLIDINGTOOL REST TO WET WHEEL.”

5. Fig. 51, illustrates a rough grinding operation on aplaner knife using the dry wheel.

USING THE TOOL REST WITHPLANER OR JOINTER KNIVES

1. Loosen four lock knobs (A) Fig. 52 and two screws(E) and carefully slide knife (B) between the top andbottom pieces (C) and (D) of the sliding tool rest. It isimportant that the bevel edge of the knife (B) is in thedown position. Also, be sure the back of the knife ispushed in so it sits against the knife adjustment barinside the tool rest.

2. Make sure knife (B) Fig. 52, protrudes out from thetop and bottom pieces (C) and (D) of the sliding toolrest at least 5/16”. If it does not, rotate adjustingknob (F) Fig. 50, clockwise to move the knifeoutward or counterclockwise to move the knife in-ward. When moving the knife inward, carefully pushthe knife (B) inward with a piece of scrap wood whileturning the knob (F) counterclockwise. When you arecertain the knife protrudes 5/16” outward from thesliding tool rest, tighten two screws (E) and fourknobs (A).

C A R E M U S T B E TA K E N W H E NHANDLING PLANER OR JOINTER

KNIVES, AS THE CUTTING EDGES ARE VERYSHARP. WEAR PROTECTIVE GLOVES WHENHANDLING THE KNIVES.

J

E

F

G

H

E

A

B

A

EF

D

C

19

7. Check to see if the bevel edge of the knife (B) Fig. 56,is flat on the grinding wheel. If an adjustment isnecessary, turn tilting screw (O) Fig. 56, until theedge of the knife is flat on the grinding wheel.

8. Fig. 57, illustrates a typical grinding operation of ajointer or planer knife.

Fig. 53

Fig. 54

Fig. 55

Fig. 57Fig. 56

4. Adjust the height of tool rest base (H) Fig. 54, bymoving locking lever (J) to the right and turningraising and lowering knob (K) until knife (B) Fig. 53,lightly touches grinding wheel (L). Then move lockinglever (J) Fig. 54 to the left to lock in place.

5. Check to see if the knife (B) Fig. 53, is parallel withgrinding wheel (L) at both ends when the knife is justcontacting the wheel.

3. Place sliding tool rest (G) Fig. 53, onto the tool restbase (H) as shown.

6. If the knife (B) Fig. 53, is not parallel with the grindingwheel, loosen screw (M) Fig. 55, and rotate tool restbase (N) until knife is parallel with grinding wheel.Then tighten screw (M) Fig. 55.

B

O

M

N

G

H

B

L

H

J

K

20

Fig. 58

REPLACING WET GRINDING WHEEL

DISCONNECT THE MACHINE FROMTHE POWER SOURCE.

1. Using the wrench (A) Fig. 58, supplied, remove thewheel locking nut (B).

2. Remove and replace the wet wheel (C) as shown inFig. 59.

Fig. 59

Fig. 60

Fig. 62

REPLACING DRY GRINDING WHEEL

DISCONNECT MACHINE FROM THEPOWER SOURCE.

1. Remove three screws (A) Fig. 60, and side cover (B).2. Using wrench (C) Fig. 61, supplied, hold motor shaft

on inside of grinding wheel (D) to keep shaft fromturning and remove wheel nut (E). Use a 13/16wrench (not provided).

3. Remove grinding wheel (D), as shown in Fig. 62.

Fig. 61

A

C

A

E

B

A

D

C

D

B

21

Fig. 63

DRESSING THE DRY GRINDINGWHEEL

A stick type dresser (A) Fig. 63, is supplied with yoursharpening center to dress the dry grinding wheel. Bringthe dresser stick (A) forward on the tool rest until it justtouches the high point of the face of the wheel and dressthe wheel by moving the dresser stick back and forth.Repeat this operation until the face of the wheel is cleanand the corners of the wheel are square.

A

MAINTENANCEKEEP MACHINE CLEANPeriodically blow out all air passages with dry compressedair. All plastic parts should be cleaned with a soft dampcloth. NEVER use solvents to clean plastic parts. They couldpossibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses whileusing compressed air.

FAILURE TO STARTShould your machine fail to start, check to make sure theprongs on the cord plug are making good contact in theoutlet. Also, check for blown fuses or open circuit breakersin the line.

22

PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additionalinformation regarding your Delta quality product or to obtain parts, service, warranty assistance, or the locationof the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog orfor the name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product.

ACCESSORIES

Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessorywhich in normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delta factory service center or authorized service station with proof of purchase of the product within twoyears and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Deltaproduct, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motormanufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserteddefect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized byanyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable forincidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and setsforth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whetherof merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

23

NOTES

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAWBOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The LumberCompany®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™. Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. LasMarcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estarregistradas en otros países.

PORTER-CABLE • DELTA SERVICE CENTERS(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)

Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, AuthorizedService Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you willbe directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchasgrandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesoriospara los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centrode Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.

ARIZONATempe 85282 (Phoenix)2400 West Southern AvenueSuite 105Phone: (602) 437-1200Fax: (602) 437-2200

CALIFORNIAOntario 91761 (Los Angeles)3949A East Guasti RoadPhone: (909) 390-5555Fax: (909) 390-5554

San Diego 921117638 Clairemnot Blvd.Phone: (858) 277-9595Fax: (858) 277-9696

San Leandro 94577 (Oakland)3039 Teagarden StreetPhone: (510) 357-9762Fax: (510) 357-7939

COLORADOArvada 80003 (Denver)8175 Sheridan Blvd., Unit SPhone: (303) 487-1809Fax: (303) 487-1868

FLORIDADavie 33314 (Miami)4343 South State Rd. 7 (441)Unit #107Phone: (954) 321-6635Fax: (954) 321-6638

Tampa 33609 4538 W. Kennedy BoulevardPhone: (813) 877-9585Fax: (813) 289-7948

GEORGIAForest Park 30297 (Atlanta)5442 Frontage Road,Suite 112Phone: (404) 608-0006Fax: (404) 608-1123

ILLINOISAddison 60101 (Chicago)400 South Rohlwing Rd.Phone: (630) 424-8805Fax: (630) 424-8895

Woodridge 60517 (Chicago)2033 West 75th StreetPhone: (630) 910-9200Fax: (630) 910-0360

MARYLANDElkridge 21075 (Baltimore)7397-102 Washington Blvd.Phone: (410) 799-9394Fax: (410) 799-9398

MASSACHUSETTSFranklin 02038 (Boston)Franklin Industrial Park101E Constitution Blvd.Phone: (508) 520-8802Fax: (508) 528-8089

MICHIGANMadison Heights 48071 (Detroit)30475 Stephenson HighwayPhone: (248) 597-5000Fax: (248) 597-5004MINNESOTAMinneapolis 554295522 Lakeland Avenue NorthPhone: (763) 561-9080Fax: (763) 561-0653

MISSOURINorth Kansas City 641161141 Swift AvenuePhone: (816) 221-2070Fax: (816) 221-2897

St. Louis 631197574 Watson RoadPhone: (314) 968-8950Fax: (314) 968-2790

NEW YORKFlushing 11365-1595 (N.Y.C.)175-25 Horace Harding Expwy.Phone: (718) 225-2040Fax: (718) 423-9619

NORTH CAROLINACharlotte 282709129 Monroe Road, Suite 115Phone: (704) 841-1176Fax: (704) 708-4625

OHIOColumbus 432144560 Indianola AvenuePhone: (614) 263-0929Fax: (614) 263-1238

Cleveland 441258001 Sweet Valley DriveUnit #19Phone: (216) 447-9030Fax: (216) 447-3097

OREGONPortland 972304916 NE 122 nd Ave.Phone: (503) 252-0107Fax: (503) 252-2123

PENNSYLVANIAWillow Grove 19090(Philadelphia)520 North York RoadPhone: (215) 658-1430Fax: (215) 658-1433

TEXASCarrollton 75006 (Dallas)1300 Interstate 35 N, Suite 112Phone: (972) 446-2996Fax: (972) 446-8157

Houston 770434321 Sam Houston Parkway,WestSuite 180Phone: (713) 983-9910Fax: (713) 983-6645

WASHINGTONAuburn 98001(Seattle)3320 West Valley HWY, NorthBuilding D, Suite 111Phone: (253) 333-8353Fax: (253) 333-9613

PC-0104-149

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERSALBERTABay 6, 2520-23rd St. N.E.Calgary, AlbertaT2E 8L2Phone: (403) 735-6166Fax: (403) 735-6144

BRITISH COLUMBIA8520 Baxter PlaceBurnaby, B.C.V5A 4T8Phone: (604) 420-0102Fax: (604) 420-3522

MANITOBA1699 Dublin AvenueWinnipeg, ManitobaR3H 0H2Phone: (204) 633-9259Fax: (204) 632-1976

ONTARIO505 Southgate DriveGuelph, OntarioN1H 6M7Phone: (519) 767-4132Fax: (519) 767-4131

QUÉBEC1515 ave.St-Jean Baptiste, Suite 160Québec, QuébecG2E 5E2Phone: (418) 877-7112Fax: (418) 877-7123

1447, BeginSt-Laurent, (Montréal),QuébecH4R 1V8Phone: (514) 336-8772Fax: (514) 336-3505