SHARP XV-Z3000U I! PROJECTOR B PROJETOR IIn · sharp projector projecteur proyector projetor...

SHARP

PROJECTOR

PROJECTEUR

PROYECTOR

PROJETOR

XV-Z3000U

OPERATION MANUAL

MODE D'EMPLOI

MANUAL DE MANEJO

MANUAL DE OPERA_._O

I!BIIn

li.4_m| TM

Before using the projector, please read this operation manual carefully.

IMPORTANT,, For your assistance in reporting the loss

or theft of your Projector, please record Model No.: ×V-Z3000Uthe Serial Number located on the bottom

of the projector and retain this information. Sel'la_ NO,:,, Before recycling the packaging, please

ensure that you have checked the con-tents of the carton thoroughly against the

list of "Supplied accessories" on page 10.

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into thebeam of light.

WARNING: To reduce the risk of fire or electric shock, do not exposethis product to rain or moisture.

See bottom of projector.

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWSEXCEPT SPECIFIED USER

SERVICE SCREW,

CAUTION: TO REDUCE THE RiSK OF ELECTRIC SHOCK,DO NOT REMOVE COVER,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.REFER SERVICING TO QUALiFiED SERVICE

PERSONNEL.

The lightning flash with arrowhead sym-bol, within an equilateral triangle, is in-tended to alert the user to the presenceof uninsulated "dangerous voltage"within the product's enclosure that maybe of sufficient magnitude to constitutea risk or electric shock to persons.

The exclamation point within a triangleis intended to alert the user to thepresence of important operating andmaintenance (servicing) instructions inthe literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications tothis equipment not expressly approved by the manufacturer could void

the user's authority to operate this equipment. JU.S.A. ONLY J

i i

H

(D-1

WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector entersstandby mode. During normal operation, when putting the projector into standby mode abvaysuse the STANDBY/ON button on the projector or the STANDBY button on the remote control.Ensure the cooling fan has stopped before disconnecting the power cord.DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTINGTHE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rubs. These limits are designed to provide reasonabbprotection against harmful interference in a residential installation. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordancewith the operation manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or tebvision reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correcttile interference by one or more of the following measures:_, Reorient or relocate the receiving antenna._, Increase the separation between the equipment and the receiver._, Connect the equipment into an outbt on a circuit different from that to which the receiver

is connected._, Consult the deabr or an experienced radio/TV technician for help. [U.S.A. ONLY I

Declaration of conformitySHARP PROJECTOR MODEL XV-Z3000U

This device complies with Part 15 of the FCC rubs. Operation is subject to the followingconditions: (1) This device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135TEL: 1-800-BE-SHARP (1-800-237-4277) [U.S.A. ONLY]

PRODUCT DISPOSALThis projector utilizes tin-bad solder, and a pressurized lamp containing a small amount ofmercury. Disposal of these materials may be regulated due to environmental considerations.For disposal or recycling information, please contact your local authorities or, if you arelocated in the United States of America, the Electronic Industries Alliance: www.eiae.org.

Caution Concerning Lamp Replacement

See "Replacing the Lamp" on page 54.

This SHARP projector uses a DMD panel. This very sophisticated panel contains 983,040 pixeis(micromirrors). As with any high technology ebctronic equipment such as large screen TVs,video systems and video cameras, there are certain acceptable tolerances that the equipmentmust conform to.This unit has some inactive pixeb within acceptable tolerances which may result in inactive dotson the picture screen. This will not affect the picture quality or the life expectancy of the unit.

(D-2

How to Read this Operation Manual

[] The specifications are slightly different, depending on the model. However, you can connect andoperate all models in the same manner.

• In this operation manual, the illustration and the screen display are simplified for explanation, andmay differ slightly from the actual display.

Us ng the Menu Screen

ENTER button

i i is displayed

letted input mode is displayed

Press _- or 4 to select the menu

Menu screen

Picture

Fine Sync

Options1

Options2

_Note

* The 'Rne Syno' menu is not availablefor _NPUT 3 or _NPUT 4

Selected input mode

used in

this operation

used in

this step

On-screen

display

Info ........ Indicates safeguards for using the projector.

Note ......... Indicates additional information for setting up and operating theprojector.

[ For Future Reference

Maintenance Troubleshooting

iii i

iii ii

iii i

iii_ i

iii_i i

iiii

ii! ii_ii i

Index

0-3

Contents

Preparing

introduction

How to Read this Operation Manual .... 3Contents ............................................... 4IMPORTANT SAFEGUARDS ............... 6Accessories ........................................ 10Part Names and Functions ................. 11

Inserting the Batteries .......................... 14Usable Range ...................................... 15

Quick Start

Quick Start .......................................... 16

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18Standard Setup (Front Projection) ....... 18

Ceiling=mount Setup ............................ 18Projection (PRJ) Mode ......................... 19

Picture (Screen) Size and ProjectionDistance ............................................. 20

Connections

Samples of Cables for Connection ..... 22Connecting to Video Equipment ......... 23Connecting to a Computer ................. 26Controlling the Projector by a

Computer .......................................... 27

Basic Operation

Turning the Projector On/Off .............. 28

Connecting the Power Cord ................ 28Turning the Projector on ....................... 28

Turning the Power off (Putting theProjector into Standby Mode) ........... 29

Image Projection ................................. 29

Switching the Input Mode .................... 29

Adjusting the Projected Image ............ 30Correcting Trapezoidal Distortion ........ 32Resize Mode ......................................... 36

Useful Features

Operating with the Remote Control .... 38

Shifting the Projected Image Vertically

(Image Shift) ...................................... 38Switching the Iris Setting ..................... 38

Freezing a Moving Image .................... 38Selecting the Picture Mode .................. 38

Menu Items ......................................... 39

Using the Menu Screen ...................... 41

Menu Selections (Adjustments) ........... 41

Picture Adjustment ("Picture" menu) .. 43

Selecting the Picture Mode .................. 43

Adjusting the Image ............................. 43Adjusting the Color Temperature ......... 44

Adjusting the Colors ............................. 44Progressive ........................................... 44

Reducing Image Noise (DNR) ............. 45Switching the Iris Setting ..................... 45

Lamp Setting ........................................ 45

Computer Image Adjustment

("Fine Sync" menu) ........................... 46

Adjusting the Computer Image ........... 46

Special Modes Setting ......................... 46Auto Sync (Auto Sync Adjustment) ..... 46

Checking the Input Signal ................... 46

Using the "Options" Menu ................... 47Adjusting the Image Position ............... 47

Adjusting the Overscan ....................... 47Adjusting the Vertical Size of the Display

(Subtitle Setting) ................................ 47Setting On=screen Display ................... 48

Setting the Video System ..................... 48Signal Type Setting .............................. 48

Selecting the HDMI Setting .................. 48Selecting the Background Image ........ 48Auto Power Off Function ...................... 49

Checking the Lamp Life Status ........... 49

Reversing/Inverting ProjectedImages ............................................... 49

Selecting the Transmission Speed(RS-2320) .......................................... 50

Reducing the Power Consumption Whenthe Power Is in Standby Mode .......... 50

Fan Mode Setting ................................. 50Returning to the Default Settings ......... 50

Selecting the On-screen DisplayLanguage ........................................... 50

(D-4

Ref÷_'÷nce

Appendix

Maintenance ....................................... 51

Maintenance Indicators ...................... 52

Regarding the Lamp ........................... 54

Lamp ..................................................... 54Caution Concerning the Lamp ............ 54

Replacing the Lamp ............................. 54Removing and Installing

the Lamp Unit .................................... 55Resetting the Lamp Timer .................... 56

Connecting Pin Assignments ............. 57RS-232C Specifications and Command

Settings ............................................ ,58Computer Compatibility Chart ............ 59Troubleshooting .................................. 60Service Information (For the U.S.) ..... 61Specifications ..................................... 62Dimensions ......................................... 63Index ................................................... 64CONSUMER LIMITED WARRANTY

(VALID IN USA ONLY) ..................... 65LIMITED WARRANTY

(VALID IN CANADA ONLY) .............. 66

i_ iii

i i i

ii/

0-5

iMPORTANT SAFEGUARDSCAUTION: Please read all of these instructions before you operate this productand save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineeredand manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT INPOTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat thesafeguards incorporated in this product, observe the following basic rules for its installation,use and servicing.

1.

2.

3.

4.

5.

6.

7.

Read instructionsAll the safety and operating instructions shouldbe read before the product is operated.Retain InstructionsThe safety and operating instructions should beretained for future reference.

Heed WarningsAll warnings on the product and in the operatinginstructions should be adhered to.Follow instructionsAll operating and use instructions should befollowed.

CleaningUnplug this product from the wall outlet beforecleaning. Do not use liquid cleaners or aerosolcleaners. Use a damp cloth for cleaning.AttachmentsDo not useattachments not recommended by theproduct manufacturer as theymay cause hazards.Water and MoistureDo not use this product near water for example,near a bath tub, wash bowl, kitchen sink, orlaundry tub; in a wet basement; or near aswimming pool; and the like.AccessoriesDo not place this product on an unstable cart,stand, tripod, bracket, or table. The product mayfall, causing serious injury to a child or adult, andserious damage to the product. Use only with acart, stand, tripod, bracket, or tablerecommended by the manufacturer, or sold withthe product. Any mounting of the product shouldfollow the manufacturer's instructions, and shoulduse a mounting accessory recommended by themanufacturer.

TransportationA product and cartcombination should bemoved with care. Quickstops, excessive force,and uneven surfaces maycause the product and cartcombination to overturn.

10. VentilationSlots and openings in the cabinet are providedfor ventilation to ensure reliable operation of theproduct and to protect it from overheating, andthese openings must not be blocked or covered.Theopenings should never be blocked by placingthe product on a bed, sofa, rug, or other similarsurface. This product should not be placed in abuilt-in installation such as a bookcase or rackunless proper ventilation is provided or themanufacturer's instructions have been adheredto.

11. Power SourcesThis product should be operated only from thetype of power source indicated on the markinglabel. If you are not sure of the type of powersupply to your home, consult your product dealeror local power company. For products intendedto operate from battery power, or other sources,refer to the operating instructions.

12. Grounding or PolarizationThis product isprovided with one of the followingtypes of plugs. If the plug should fail to fit into thepower outlet, please contact your electrician.Do not defeat the safety purpose of the plug.a. Two-wire type (mains) plug.b. Three-wire grounding type (mains) plug with

a grounding terminal.This plug will only fit into a grounding typepower outlet.

13. Power-Cord ProtectionPower-supply cords should be routed sothat theyare not likely to be walked on or pinched by itemsplaced upon or against them, paying particularattention to cords at plugs, conveniencereceptacles, and the point where they exit fromthe product.

14. LightningFor added protection for this product during alightning storm, or when it is left unattended andunused for long periods of time, unplug it fromthe wall outlet and disconnect the cable system.This will prevent damage to the product due tolightning and power-line surges.

(D-6

15. OverloadingDo not overload wall outlets, extension cords, orintegral convenience receptacles as this canresult in a risk of fire or electric shock.

16. Object and Liquid EntryNever push objects of any kind into this productthrough openings as they may touch dangerousvoltage points or short-out parts that could resultin a fire or electric shock. Never spill liquid of anykind on the product.

17. ServicingDo not attempt to service this product yourself asopening or removing covers may expose you todangerous voltage or other hazards. Refer allservicing to qualified service personnel.

18. Damage Requiring ServiceUnplug this product from the wall outlet and referservicing to qualified service personnel underthefollowing conditions:a. When the power-supply cord or plug is

damaged.b. If liquid hasbeen spilled, or objects havefallen

into the product.c. If the product has been exposed to rain or

water.d. If the product does not operate normally by

following the operating instructions.Adjust onlythose controls that are covered by theoperating instructions, as an improperadjustment of other controls may result indamage and will often require extensive workby a qualified technician to restorethe productto normal operation.

e. If the product has been dropped or damagedin any way.

f. When the product exhibits a distinct changein performance, this indicates a need forservice.

19. Replacement PartsWhen replacement parts are required, be surethe service technician has used replacementparts specified by the manufacturer or have thesame characteristics as the original part.Unauthorized substitutions may result in fire,electric shock, or other hazards.

20. Safety CheckUpon completion of any service or repairs to thisproduct, ask the service technician to perform

safety checks to determine that the product is inproper operating condition.

21. Wall or Ceiling MountingThis product should be mounted to a wall orceiling only as recommended by themanufacturer.

22. HeatThis product should be situated away from heatsources such as radiators, heat registers, stoves,

orproduceother heat.products (including amplifiers)that

_i i_

,, DLP TM (Digital Light Processing), DMD TM (Digital Micromirror Device) and BrilliantColor TM

are trademarks of Texas Instruments, Inc.,, Microsoft ®and Windows ®are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

,, PC/AT is a registered trademark of International Business Machines Corporation in theUnited States.

,, Macintosh ® is a registered trademark of Apple Computer, Inc. in the United States and/orother countries.

,, HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or regis-tered trademarks of HDMI Licensing LLC.

,, All other company or product names are trademarks or registered trademarks of theirrespective companies.

,, Some IC chips in this product include confidential and/or trade secret property belongingto Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,reverse engineer, reverse assemble or discompile the contents thereof.

0-7

Caution concerning the lamp unit

[] Potential hazard of glass par-ticles if lamp ruptures. Incase of lamp rupture, contactyour nearest AuthorizedSharpVision Service Centeror Dealer for replacement.See "Replacing the Lamp" onpage 54.

Caution concerning the setup of the pro-

jector

[] For minimal servicing and to maintain highimage quality, SHARP recommends that thisprojector be installed in an area free fromhumidity, dust and cigarette smoke. When theprojector is subjected to these environments,the vents and lens must be cleaned more of-

ten. As long as the projector is regularlycleaned, use in these environments will not

reduce the overall operation life of the unit.Internal cleaning should only be performedby an Authorized SharpVision Service Cen-ter or Dealer.

When using the projector in high-altitude

areas such as mountains (at altitudes of

approximately 4,900 feet (1,500 meters)

or more)

[] When you use the projector in high-altitudeareas with thin air, set "Fan Mode" to "High".Neglecting this call affect the longevity of theoptical system.

Warning about placing the projector in

a high position

[] When placing the projector in a high position,ensure that it is secured carefully to avoid per-sonal injury caused by the projector fallingdown.

Do not subject the projector to hard im-

pact and/or vibration.

[] Protect the lens so as not to hit or damagethe surface of the lens.

Rest your eyes occasionally.

[] Continuously watching the screen for longhours will cause eye strain. Be sure to occa-

sionally rest your eyes.

Do not set up the projector in places ex-

posed to direct sunlight or bright light.[] Position the screen so that it is not in direct

sunlight or room light. Light falling directly onthe screen washes out the colors, makingviewing difficult. Close the curtains and dimthe lights when setting up the screen in asunny or bright room.

Caution regarding placing of the projec-tor

[] Place the projector on a level site within theadjustment range (8 degrees) of the adjust-ment foot.

[] After the projector is purchased, a faint smellfrom the vent may appear when the power isfirst turned on. This is normal and is not a

malfunction. It will disappear after the projec-tor is used for a while.

(D-8

Avoid locations with extremes of tem-

perature.

[] The operating temperature of the projector isfrom 41°P to 95°P (+5°C to +35°C).

[] The storage temperature of the projector is

from -4°F to 140°F (-20°C to +60°C).

Do not block the exhaust and intake

vents,

[] Allow at least 11 W16 inches (30 cm) of spacebetween the exhaust vent and the nearestwall or obstruction.

[] Be sure that the intake vent and the exhaustvent are not obstructed.

[] If the cooling fan becomes obstructed, a pro-tection circuit will automatically put the pro-jector into standby mode to prevent overheatdamage. This does not indicate a malfunc-tion. (See pages 52 and 53.) Remove the pro-jector power cord from the wall outlet and waitat least 10 minutes. Place the projector wherethe intake and exhaust vents are not blocked,

plug the power cord back in and turn on theprojector. This will return the projector to thenormal operating condition.

[] Whenturningofftheprojector,thecoolingfanrunstodecreasetheinternaltemperatureforawhile.Unplugthepowercordafterthecool-ingfanstops.Theperiodthecoolingfanrunswillvary,dependingonthecircumstancesandtheinternaltemperature.

Cautionregarding usage of the projector

[] When using the projector, be sure not to sub-ject it to hard impact and/or vibration, as thiscan result in damage. Take extra care withthe lens. Before moving the projector, be sure

to unplug the power cord from the wall outlet,and disconnect any other cables connectedto it.

[] Do not carry the projector by holding the lens.[] When storing the projector, re-attach the lens

cap. (See page 1t ).[] Do not expose the projector to direct sunlight

or place next to heat sources. Doing so mayaffect the cabinet color or cause deformation

of the plastic cover.

Other connected equipment

[] When connecting a computer or other audio-visual equipment to the projector, make the

connections AFTER unplugging the powercord of the projector from the AC outlet andturning off the equipment to be connected.

[] Please read the operation manuals of the pro-

jector and the equipment to be connected forinstructions on how to make the connections.

Using the projector in other countries

[] The power supply voltage and the shape of

the plug may vary depending on the regionor country you are using the projector in.When using the projector overseas, be sureto use an appropriate power cord for the coun-

try you are in.

Temperature monitor function

[] If the projector starts to overheat due to setup

_roblems or blockage of the air vents, "_" and

" will illuminate in the lower left cornerof the picture. If the temperature continues torise, the lamp will turn off, the temperature warn-

ing indicator on the projector will blink, and aftera 90-second cooling-off period the projector will

enter standby mode. Refer to "Maintenance In-dicators" on page 52 for details.

_lnfo

,, The cooling fan regulates the internal tem-perature, and its performance is automatically

controlled. The sound of the fan may changeduring projector operation due to changes inthe fan speed.This does not indicate malfunc-tion.

,, Do not unplug the power cord during projec-tion or cooling fan operation. This can causedamage due to rise in internal temperature,as the cooling fan also stops.

0-9

Accessories

Supplied accessories

f--

@

--%

®

©_5

Remote controlRRMCGA444WJSA

Two R-03 batteries("AAA" size, UM/SUM-4,

HP-16 or similar)

Lens cap (attached)CCAPHA024WJSA

,, Operation manual

Power cordfor U.S. and

Canada, etc.(6' (1.sm))

QACCDA007WJPZ

Optional accessories

[] Lamp unit AN=100LP

[] DIN=D-sub RS=232C adaptor (5 57/U' (15 cm)) AN=A1RS

[] 3 RCA to 15-pin D-sub cable (10' (3.0 m)) AN-C3CP2

Note

• Some of the optional accessories may not be available depending on the region. Please check withyour nearest Authorized SharpVision Service Center or Dealer.

(D -10

Part Names and Functions

Numbers in _ refer to the main pages in this operation manual where the topicis explained.

Prejeeter

Power _

ndcatoSTANDBY/ONbutton

For turning thepower on andputting theprojector intostandby mode.

ENTER button

For setting

items selectedor adjusted onthe menu.

RESlZEbutton_lr --/For swkchkrgthe screensize.

Focus ringFor adjustingthe focus.

Lamp indicator

-- _ Temperature warningindicator

_ INPUT buttons (A/T)For switching input mode1, 2, 3, 4, 5or 6.

MENU buttonFor displayingadjustment andsetting screens.

Adjustment buttons(At,/_'/4/_)

For selecting menu items.

Intake vent

Zoom ringFor enlarging/reducing the picture.

HEIGHT _ )_11ADJUST J

lever 1

Remote controlsensor (front)

Push both sides of the lens capto attach or remove.

Q-11

Part Names and Functions (Continued)


Rear View

intake vent _

AC socket \\\\_,_ -,''_ _'Connect the _

Exhaust vent

Remote control

sensor (rear)

KensingtonSecurity Standardconnector

Terminal Page

©Description

INPUT 1,2 terminalConnecting video equipment with component output terminal (DVDplayer, DTV decoder, DVD recorder with hard disc, etc.).

INPUT 3 terminal

Connecting video equipment with S-video output terminal (VCR, DVDplayer, etc.).

INPUT 4 terminal

Connecting video equipment without S-video output terminal.

INPUT 5 terminal[] Connecting video equipment with component output terminal

(DVD player, DTV decoder, DVD recorder with hard disc, etc.).

[] Connecting the computer.

INPUT 6 terminalConnecting video equipment with HDMI output terminal.

RS-232C terminalConnecting the computer to control the projector.

TRIGGER terminalWhen the projector is turned on, a control signal (DC 12V) outputs from thisterminal. If an electric screen or other compatible device is connected, itcan be turned on when the projector is turned on.

O -12


STANDBY button

For putting theprojector into thestandby mode.

KEYSTONE buttonFor entering theKeystone Correctionmode.

RETURN buttonFor returning to theprevious menu screenduring menu operations.

AUTO SYNC button

For automaticallyadjusting imageswhen connected to acomputer.

RGB/COMR button

For switching to therespective input signal type.

m

FREEZE button ___For freezing images.

Backlight buttonFor lighting all buttons on theremote control.

BI!t

-I l:l

ON buttonFor turning the power on.

INPUT 1,2, 3, 4, 5 and 6buttonsFor switching to therespective input modes.

MENUbutton ii (For displaying adjustment

and setting screens.

Adjustment buttons

• For selecting menu items.• For adjusting the Keystone

Correction when in theKeystone Correction mode.

ENTER button

For setting items selected

or adjusted on the menu.

RES,ZEbuttonFor switching the screen

size (STRETCH, SIDEBAR, etc.).

PICTURE MODE buttonFor selecting the appropriatepicture.

IRIS button

For switching "HIGHBRIGHTNESS MODE",

"MEDIUM MODE" and"HIGH CONTRAST MODE".

,MAGESR,FTbuttonsFor shifting the projectedimage vertically.

Using the Kensington Lock on the projector• This projector has a Kensington Security Standard connector for use with a Kensington

MicroSaver Security System. Refer to the information that came with the system for instructionson how to use it to secure the projector.

Q-13

Part Names and Functions (Continued)

inserting the Batteries

"_ Press the A mark on the cover and slide itin the direction of the arrow.

i

ii 12i osort,,obot,or,os.Insert the batteries making sure the polarities

correctly match the _+) and (._ marks inside the

battery compartment.

iN%jY

Attach the cover and slide it until it clicks

into place.

//_ Caution

• Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type•

,, Insert the batteries making sure the polarities correctly match the _ and (_) marks inside the batterycompartment.

,, Batteries of different types have different properties, therefore do not mix batteries of different types•,, Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.,, Remove the batteries from the remote control once they have run out, as leaving them in can cause them

to leak.

Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and thenremove them using a cloth.

_, The batteries included with this projector may run down in a short period, depending on how they are kept.Be sure to replace them as soon as possible with new batteries.

,, Remove the batteries from the remote control if you will not be using the remote control for a long time.Comply with the ru!es (ordinance) of each local government when disposing of worn-out batteries•

(D -14

Usable RaHgeThe remote control can be used to control the projector within the ranges shown in the illustration.

Remote control sensor (front)

Remote

control signaltransmitters

23' (7 m)

Remote control sensor (rear)

I,

Remote control

Remotecontrol signaltransmitters

23' (7 m) //

Remote control

_,Note

o The signal from the remote control can be reflected off a screen for easy operation. However, theeffective distance of the signal may differ depending on the screen material.

When using the remote control

,, Ensure that you do not drop, expose to moisture or high temperature.

/

_i_ _i _

,, The remote control may malfunction under a fluorescent lamp. In this case, move the projectoraway from the fluorescent lamp.

?

Q-15

Quick Start

This section shows the basic operation (projector connecting with the video equipment).For details, see the page described below for each step.

Setup and P_ejectienIn this section, connection of the projector and the video equipment is explained using one ex-ample.

--_-, 8 }STANDBY/ONbutton

5 INPUT buttons

__6 FOCUS ring6 Zoom dng

_'__ 6 HEIGHTADJUST lever

8 STANDBY button.....'.................. :3 ON button

<_j <,j......... 5 INPUT 4 button

7 KEYSTONE button

Adjustment buttons(A/T/_/_-)

%1_ <_ii_i_

ENTER button

INPUT 4 terminal

Connect the audio output ofany video devices to an

AC appropriate audio device.

0 -16

Select the "INPUT 4" using the INPUT buttons on the projector or the INPUT 4 button on the

Focus ring

1. Press G KEYSTONE on the remote control.

2. Press J,/T/_/_ oil the remote control to set the upper-left position of the projected image.3. Press C_ ENTER on the remote control to set the position.4. Follow steps 2 and 3 to also set the upper-right, lower-right, and lower-left positions of the

projected image.,, When you confirm the lower [eft poskion, the screen adjustments wiI[ be set and setup wiI[

end.

Press the STANDBY/ON button on the projector or the STANDBY button on the remote control,and then press the button again while the confirmation message is displayed, to put the projectorinto standby mode.

On-screen DisplayOn the On the remoteprojector control

STANDBY/ON

Unplug the power cord from the AC outlet after the cooling fan stops.

(D-17

ett|ng up the Projector

Setting up the ProjectorFor optimal image quality, position the projector perpendicular to the screen with the projector's feetflat and level. Doing so will eliminate the need for Keystone correction and provide the best imagequality.

Standard Setup {Front P_,ejectien}[] Place the projector at the required distance from the screen according

to the desired picture size. (See page 20.)

Example of standard setup

H_

Screen

Jgo Lens center _:_"_]-L

Note

o Refer to page 20 for additional information concerning "Picture (Screen) Size and Projection Dis-tance".

@eimingo_eUnt getup

[] It is recommended that you use the optionalSharp ceiling-mount bracket for this installa-tion. Before mounting the projector, contactyour nearest Authorized SharpVision ServiceCenter or Dealer to obtain the recommendedceiling-mount bracket (sold separately).• AN-XRCM30 ceiling-mount bracket (for

U.S.A.).• AN-60KT ceiling-mount bracket, its AN-

TK201 and AN-TK202 extension tubes (forcountries other than the U.S.A.).

[] Invert the image by setting "Ceiling + Front"in "PRJ Mode". See page 49 for use of thisfunction.

(J_D-18

Projection Modeii i

The projector can use any of the 4 projection modes, shown in the diagram below. Select the modemost appropriate for the projection setting in use. (You can set the PRJ Mode in "Options2" menu.See page 49.)

[] Table mounted, front projection [] Ceiling mounted, front projection

Menu item _ "Front"

[] Table mounted, rear projection(with a translucent screen)

Menu item -_ "Ceiling + Front"

[] Ceiling mounted, rear projection(with a translucent screen)

Menu item _ "Ceiling + Rear"

Refer to page 20 for additional information concerning "Picture (Screen) Size and Projection Distance".

Example: When using a wide screen (16:9)

Picture (Screen) Size300"

200"

ProjectionDistance ...........

Q-19

Setting up the Projector (Continued)

Picture _$creen} Size and Projection Distance

The projection screen size varies according to the distance from the lens of the projec-tor to the screen. Install the projector so that projected images are projected onto thescreen at the optimum size by referring to the table below. Use the values in the tableas a reference when installing the projector.

When using a wide screen (16:9) and projecting 16:9 image

Picture (Screen) size

Diag. [%]

300" (762 cm)

270" (686 crn)

250" (635 crn)

2OO" (508 cm)

150" (381 crn)

100" (254 crn)

80" (203 crn)

70" (178 cm)

60" (152 crn)

40" (102 cm)

Width

261" (664 cm)

235" (598 cm)

218" (553 cm)

174" (443 cm)

131" (332 cm)

87" (221 cm)

70" (177 cm)

61" (155 cm)

52" (133 cm)

35" (89 cm)

Height

147" (374 crn)

132" (336 crn)

123" (311 crn)

98" (249 crn)

74" (187 crn)

49" (125 crn)

39" (100 crn)

34" (87 crn)

29" (75 crn)

20" (50 cm)

7`: Picture (Screen] size (diag ] (in/cm)L: Projection distance (ft/m)LI: Minimum projection distance (ft/m)L2: Maximum projection distance (ft/m)

Projection distance [L]

Minimum iLl] Maximum[L2]

29' 9" (9.1 m) 34' 5" (10.5 m)

26' 9" (8.2 m) 30'11" (9.4 m]

24' 9" (7.5 m) 28' 8" (8.7 m]

19'10" (6.0 m) 22'11" (7.0 m]

14'10" (4.5 m) 17'2" (5.2m]

9'11" (3.0m) 11'6" (3.5m]

7'11" (2.4m) 9'2" (2.8m]

6'11" (2.1 m) 8' 0" (2.4 m]

5'11" (1.8m) 6'11" (2.1 m]

4' 0" (1.2 m) 4' 7" (1.4 m]

Distancefro_,thelenscenter

to thebottor;'of theimage[Hi

21 1/32" (53 cm]

1815/16" (48 Cm]

17 Wa2" (45 cm]

14 %4" (36 cm]

10 33/64" (27 cm]

7 %4" (18 cm]

5 3_/64" (14 cm]

4 2_/32" (12 cm]

4 13/64" (11 cm]

2 51/64" ( 7 crn]

H: Distance from the lens center to the bottom of the image (in/crn)S: Adjustable range of image position (in/cm] See page 47

Adjustable range of

image position iS]

+429/62 " (+ 12.5 cm)

+4W62" (+ 11.2 cm)

+45/64 '` (+ 10.4 cm)

+3 17/64" (+8.3 cm)

+2 29/64" (+6.2 crn]

+1 4V64" (+4.2 cm]

+1 5/W' (+3.3 crn]

+1 9/64" (+2.9 cm]

+ 66/64" (+2.5 cm]

+ 2V62" (+1.7cm]

The formula for picture size and projection distance[Feet/Inches] [mfcm]L1 (ft] 008019;(/03048 L1 (m] 003019XL2(ft) 008493;(/03048 L2(m] 0034987`H (in) 0178087` / 254 H (cm] 0178087,S (in] +004151;(/254 S (cm] +0041517`

When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)

Picture (Screen) size

Diag. [Z]

300" (762 cm]

270" (686 cm]

250" (635 cm]

200" (508 cm]

150" (381 cm]

100" (254 cm)

80" (203 cm]

70" (178 cm)

60" (152 cm]

40" (102 cm]

Width

240"(610 cm)

216" (549 cm)

200"(508 cm)

160" (406 cm)

120" (305 cm)

80" (203 cm)

64" (163 cm)

56" (142 cm)

48" (122 cm)

32" (81 cm]

Height

180" (457 cm)

162" (411 cm)

150" (381 cm)

120" (305 cm)

90" (229 cm)

60" (152 cm)

48" (122 cm)

42" (107 cm)

36" (91 crn]

24" (61 cm]

7`: Picture (Screen] size (diag ] (in/cm]L: Projection distance (ft/m)LI: Minimum projection distance (ft/m)L2: Maximum projection distance (ft/m)

Projection distance [L]

Minimum iLl] Maximum[L2]

36'4" (11.1 m 42'1" (12.8m

32' 9" (10.0 m 37' 10"(11.5 m

30'4" (9.2m) 35'1" (10.7m

24' 3" (7.4 m) 28' 1" (8.6 m)

18'2" (5.5m) 21'0" (6.4m)

12'1" (3.7m) 14'0" (4.3m)

9'8" (3.0m) 11'3" (3.4m)

8' 6" (2.6 m) 9' 10" (3.0 m)

7' 3" (2.2 m) 8' 5" (2.6 m)

4' 10" (1.5 m) 5' 7" (1.7 m)

Distancefro_,thelenscenter

to thebottor;'of theimage[Hi

25 47/64" (65 cm]

23 IV64" (59 crn]

21 29/64" (54 cm]

17 _/32" (44 cm]

12 7/8" (33 cm]

8 37/64" (22 cm]

6 56/64" (17 cm]

6" (15 cm]

59/64 ,' (13 cm]

37/16" (9 crn]

H: Distance from the lens center to the bottom of the image (in/crn)S: Adjustable range of image position (in/cm] See page 47

Adjustable range of

image position iS]

+6" (+ 15.2 crn)

+ 5 W32" ( + 13.7 crn)

+5" (+ 12.7 crn)

+4 (+ 10.2 crn)

+3" (+7.6 cm)

+2" (+5.1 cm)

+1 Wa2" (+4.1 cm)

+1 Ws2" (+3.6 crn)

+1 W64" (+3.0 crn)

+ 51/64" (+2.0 cm)

The formula for picture size and projection distance[Feet/inches] [mfcm]L1 (ft] 003694X/03048 L1 (m] 003694XL2 (ft] 004276X / 03048 L2 (m] - 0042767`H (in] 0217947` / 254 H (cm] 0217947,S (in] +005087` / 254 S (cm] +005087`

(:D -20

When using a normal screen (4:3) and projecting 16:9 image

Picture (Screen) size Projection distance iLl

Diag. ix]

300" (762 crn)

270" (686 cm)

250" (635 crn)

200" (508 cm)

150" (381 crn)

100" (254 crn)

80" (203 crn)

70" (178 crn)

60" (152 cm)

40" (102 crn)

Width

240" (610 crn)

216" (549 cm)

200" (508 crn)

160" (406 crn)

120" (305 crn)

80" (203 crn)

64" (163 crn)

56" (142 crn)

48'* (122 cm)

32" (81 crn)

Height

180" (457 crn)

162" (411 crn)

150" (381 crn)

120" (305 crn)

90" (229 crn)

60" (152 crn)

48" (122 crn)

42" (107 crn)

36" (91 cm)

24" (61 cm)

;(: Picture (Screen) size (diag) (in/cm)L: Projection distance (ft/m)LI: Minimum projection distance (ft/m)L2: Maximum projection distance (ft/m)

Minimum iLl] Maximum [L2]

27' 3" (8.3 m) 31' 7" (9.6 m)

24' 7" (7.5 rn) 28' 5" (8.7 m)

22' 9" (6.9 m) 26' 4" (8.0 m)

18'2" (5.5m) 21'0" (6.4m)

13'8" (4.2ra) 15'9" (4.8m)

9'1" (2.8m) 10'6" (3.2m)

7' 3" (2.2 ra) 8' 5" (2.6 m)

6' 4" (1.9 ra) 7' 4" (2.2 m)

5' 5" (1.7 rn) 6' 4" (1.9 m)

3' 8" (1.1 m) 4' 2" (1.3 m)

H: Distance from the lens center to the bottom of the image (in/cm)S: Adjustable range of image position (in/cm) See page 47

Distancefromthe lenscenterto

the bottor,,ofthe i_'age[H]

19 _/ld' (49 crn)

173/8 ,' (44 cm)

16 3/32,' (41 crn)

12 %" (33 crn)

9 21/s2" (25 crn)

67/16 '* (16 crn)

59/64,' (13 crn)

4 1/2" (11 crn)

3 ss/B4" (10 cm)

2 37/64" (7 crn)

Adjustable range of

image position iS]

+41/2 '` (+ 11.4 crn)

+43/64" (+ 10.3 crn)

+33/4 '` (+9.5 crn)

+3 (+7.6 cm)

+21/4 '` (+5.7 cm)

+1 1/2" (+3.8 crn)

+1 13/64" (+3.0 cm)

+1 s/64" (+2.7 cm)

+ 2e/32" (+2.3 cm)

+ 19/32" (+1.5 crn)

The formula for picture size and projection distance[Feet/inches] [mfcm]L1 (ft) 002771;(/03048 L1 (m) 002771;(L2 (ft) 003206;(/03048 L2(m) 003206;(H (in) 0 16346X / 254 H (cm) 0 16346;(S (in} +00381X / 254 S (cm) +003817,

Note

'_ Refer to page 18 concerning "Projection distance iLl" and "Distance from the lens center to the

bottom of the image [H]'.,, Allow a margin of error in the values in the diagrams.

ul i_i

Ul i

(D -21

:::_::*z_ '¸¸_ .

Samples of Cables for Connection

• For more details of connection and cables, refer to the operation manual of the connecting equipment.• You may need other cables or connectors not listed below.

Input CableEquipment Signal

Audio-visual HDMI cable (commercially available)

equipment HDMI _--//_video

Camera/

video game

Computer

Compo-nent

video

Compo-nent

video

Component cable (commercially available)

3 RCA to 15-pin D-sub cable (optionalaccessory: AN-C3CP2)

S-video

Video

S-video cable (commercially available)

Video cable (commercially available)

Compo-nent

video

Compo-nent

video

Cables for a camera or a video game

3 RCA to 15-pin D-subCables for a camera cable (optional

S-video

Video

RGBvideo

(commercially available)



RGB cable (commercially available)

Terminal on theprojector

INPUT6

INPUT], 2

INPUT5

INPUT3

INPUT4

INPUT1,2

INPUT5

cor,,_oN_m

INPUT3

INPUT4

INPUT5

O -22

Connecting to Video Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the ACoutlet and turn off the devices to be connected. After making all connections, turn on the

projector first and then the other devices.

When connecting the component video equipment to the component input termi-nal on the projector (INPUT1 or INPUT2)

To component output(Y, CB/PB, CR/PR) terminal

To INPUT1 terminal

ill!

iii_i

Q -23

Connecting toVideo Equipment (Continued)

When connecting to equipment with S=video output terminal (iNPUT3)

To S-video output terminal

To INPUT3 terminal

S-video cable


When connecting to equipment with video output terminal (iNPUT4)

To video out put terminal

To INPUT4 terminal

t©


0 -24

When connecting the component video equipment to the cemputer=RGB/component input terminal on the projector (INPUT5)

Tocomponent output(Y, CB/PB, CR/PR) terminal

To INPUTSterminal

When connecting to equipment with HDMI output teminal (INPUT6)

HDMI is a new specialized interface capable of delivering a video and audio signal tothe terminal using just one cable. Since this projector does not support an audio signalby itself, use an amplifier or other audio device.For video connection, use a cable that conforms to HDMI standards. Using cables thatdo not conform to HDMI standards may result in a malfunction.

To HDMI output terminal [HDMI compatible device]I__. To INPUT6terminal

oa le/type*/ ..... )

Note

_,HDMI (High Definition Multimedia Interface) is a digital AV interface that can deliver a high=defini-

tion video signal, multi-channel audio signal, and bPdirectional control signal all in just one cable.,_Because it is compatibb with the HDCP (High=bandwidth Digital Content Protection) system, the

digital video signal does not degrade when transmitted, and a high-quality image with a simpleconnection can be enjoyed.

_,When a DVl to HDMI conversion cable is connected to the HDMI terminal, a proper picture may notbe displayable.

x_

xi i

iiil

_ill { {i!_i ii iii/ i

ii!i_ iiii

i i

(D -25

_11_/_¸¸¸" • .........Connecting to a Computer

When connecting a computer, ensure that it is the last device to be turned on after all theconnections are made.

Ensure that you have read the operation manuals of the devices to be connected before makingconnections.

To RGB output terminalI Computer

To INPUT5 terminal

RGB cable


Note

• See page 59 "Computer Compatibility Chart" for a list of computer signals compatible with the projec=

tor. Use with computer signals other than those listed may cause some of the functions to not work.• A Macintosh adaptor may be required for use with some Macintosh computers• Contact your near-

est Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the

computer's external output port is switched on. (e.g. Press"Fn" and"F5" keys simultaneouslywhen using a SHARP notebook computer). Refer to the specific instructions in your computer's

operation manual to enable your computer's external output port•

O -26

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-232C adaptor (optional accessory: AN-A1RS) and an RS-232C serial control cable (cross type,commercially available), the computer can be used to control the projector and check the status ofthe projector. See page 58 for detail.When connecting to a computer using an RS=232C serial control cable and a DiN-

D-sub RS-2320 adaptor To RS-232C terminal

I Computer ]To RS-232C terminal

II

DIN-D-sub RS-232Cadaptor (optional 1_

accessory: AN-A1RS)

RS-232C serial control cable (cross type, commercially available)

Note

o The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

operation manual of the computer for details.• See page 58 for connection of an RS-232C serial control cable.

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. Thismay damage your computer or projector.

• Do not connect or disconnect an RS-232C sedal control cable to or from the computer while it is on.This may damage your computer.

iii i_

Q -27

Turning the Projector On/Off

Connecting the Power Cord

Plug the supplied power cord into the ACsocket on the rear of the projector.

Turning the Prejeeter en

Note that the connections to external equip-ment and power outlet should be done be-fore performing the operations written be-low. (See pages 23 to 28.)

Remove the lens cap and pressQ STANDBY/ON on the projector or_DON on the remote control.

Note

o About the Lamp indicator

The lamp indicator illuminates to indicate thestatus of the lamp.

Green: The lamp is on.Blinking in green: The lamp is warming up

or shutting down.Red:The lamp is shut down abnormally

or the lamp should be replaced.* When swkching on the projector, a slight flick-

ering of the image may be experienced withinthe first minute after the lamp has been illumi-

nated. This is normal operation as the lamp'scontrol circuitry is stabiNsing the lamp output

characteristics. It should not be regarded asfaulty operation.

o If the projector is put into standby mode andimmediately turned on again, the lamp may

take some time to start projection.

Power cord 1

Info

• English is the factory default language. If youwant to change the on=screen display to anotherlanguage, change the language according tothe procedure on page 50.

..........._ _ Lamp indicator

® /Iil_ Power indicator,, STANDBY/ON button

(D -28

Turning the Power off _Puttingthe P_jecto_ into _an_y Pao_}

"I Press QSTANDBY/ON on the pro-Z jector or @bSTANDBY_"_'on the re=

mote control, then press that but=ton again while the confirmation

message is displayed, to put the

projector into standby mode.

Unplug the power cord from the ACoutlet after the cooling fan stops.• The power indicator on the projector

blb_ksin greenwhile cooling._,Thepower indicatorchangesto redwhen

the projector finishes cooling.

Image Projection

STANDBYbutton

............. i1_c_::,_ f,, ,,.,, ',,c_;_

On-screen Display (confirmation message)

T

Xl

iiiiiillii__iii

$witeh_ng the _nput Mode

Select the appropriate input mode forthe connected equipment.

Press the appropriate iNPUT button onthe remote control to select the desiredinput mode.

,, When pressing INPUT (,_,/v) on the projector,input mode switches in the following order:

INPUT1 _ INPUT2 _ INPUT3

INPUT6 _ INPUT5 _ INPUT4

INPUTbuttonsINPUT 1 INPUT 2 INPUT 3

@@@INPUT 4 INPUT5 INPUT6

®@

(D -29

image Projection (Continued)

Adjusting the Projected I_age Zoom ring

You can adjust the focus with the focusring on the projector.

Rotate the focus ring to adjust the fo-cus while watching the projected image.

You can adjust the screen size usingthe zoom ring on the projector.

Rotate the zoom ring to enlarge orshrink the screen size.

Focus ring

The height of the projector can be ad-justed using the adjustment feet at thefront and rear of the projector.

When the screen is above the projec-tor, the projection image can be madehigher by adjusting the projector.

Li;[gth %P [_J i cftt°rgt th adJHUE_.i il_-_.

ADJUST ever.

2 Remove your hands from theHEIGHT ADJUST lever of the pro-

jector after its height has beenfinely adjusted.o The angle of projection is adjustable up

to 8 degrees from the surface on which

the projector is placed.

_jS

0 -30

Make smalladjustments•

ADJUST lever

Use the rearadjustment foot tomake the projector level.• The projector is adjustable _+1 degree

/: from the standard position_

Note

o When adjusting the height of the projector,trapezoidal distortion occurs. Follow the pro-cedures in Keystone Correction to correct thedistortion. (See page 32.)

Info

* Do not apply too much pressure on the pro-jector when the front adjustment foot comesout.

* When lowering the projector, be careful nottoget your fingers caught in the area betweenthe adjustment foot and the projector.

* Hold the projector firmly while lifting or carry-ing.

,, Do not hold by the lens area.

-- Rear adjustment foot

ill

i I

Q -31

imageproiection(continued)

Corseting Trap÷zoidaED_stort_on

When the image is projected either fromthe top or from the bottom towards thescreen at an angle, the image becomesdistorted trapezoidally.The function forcorrecting trapezoidal distortion iscalled Keystone Correction.

There are thetwo types ofthe KeystoneCorrection.1) The "GEOMETRIC ADJUSTMENT"

method corrects trapezoidal distor-tion by specifying 4 marks on thescreen.

2) The"H &V KEYSTONE" method lea =tures corrections to 2 axes (horizon=tal and vertical) based on numericalvalues.

O -32

Select the Keystone correction method.Press _ KEYSTONE on the remote control

® "GEOMETRIC ADJUSTMENT" will bedisplayed.

® Each time C-}KEYSTONE is pressed, thedisplay toggles as follows:

GEOMETRICH & V KEYSTONEADJUSTMENT

h The display disappears. _J

GEOMETRIC For correcting an image byADJUSTMENT designating the corner of the

projected image.(See page 34.)

H & V For correcting an image byKEYSTONE designating the horizontal or

vertical axes. (See page 35.)

_Note

• When corrections are made with Keystone cor-rection, the changes are saved even if thepower cord is unplugged.

_,Since Keystone correction digitally correctsthe signal, resolution may slightly decreasewhen it is used. Moir6 patterns and line dis-tortions may also be visible in detailed images.However, this is not a malfunction.

• If you cannot correct trapezoidal distortion withKeystone correction, change the placementposition of the projector.

o Straight lines and the edges of the displayedimage may appear jagged, when adjusting theKeystone setting.

• Also read "About Copyrights" on page 37.

_i _ii _ill

I i

iii ii

Q -33


Press _ KEYSTONE on the re-

mote control repeatedly until=

"GEOMETRIC ADJUSTMENT" is0_ _ displayed.

2 Adjust the focus, size, and projec-tion angle so that the screen

edges line up into the blue area.• Line up the screen edges into the blue

_j,_ area as closely as possible.

3 Press,, ,, _or_tomovetheposition for the upper left of the

I image.• Adjust the screen until the displayed red

arrows line up in the upper left.

4 Press_ ENTERtosetthepea,-tien.

_, @_/• The arrow in the upper right turns red.

5 Repeat the same procedure withthe positions for the upper right,

lower right and lower left of the

image., • When you press _ RETURN at this point,

you will return to the previous screen.• If you press _ RETURN before adjust-

ing the upper left corner, the Reset Con-firmation screen displays.

• When you confirm the lower left posi-tion, the screen adjustments will be setand the "GEOMETRIC ADJUSTMENT"

•_ ....... mode will end.

Note

• The placement of the screen and the projector

may result in the image aspect ratio becoming

slightly distorted.o Try "H&V KEYSTONE" when "GEOMETRIC

ADJUSTMENT" does not fully correct trapezoi-dal distortion.

V On-screen display

_ GE_E_RI__JUS_ENT,_A_UOT _RESET_NE_ _ END

:2 %

Blue Geometric Adjustmenta tea

Screen Upper Left Upper Right

Lower Left Lower Right

O -34

ill

Project the image and adjust thefocus, mage s ze, and projection

2 Press _ KEYSTONE on the re-mote control repeatedly untim "H &V KEYSTONE" is displayed.• When the "GEOMETRIC ADJUSTMENT"

mode has been used to adjust the im-age, a confirmation screen displays be-fore the "H & V KEYSTONE" screen, ask-ing if you want to reset the adjustmentsor not. Then select RESET.

3 Press A or _" on the remote con-

trol to align the left and right sidesof the projected image.

i

Press ,q or I_ on the remote con-

trol to align the upper and lowersides of the projected image.

Press _ KEYSTONE or _ ENTER

. on the remote c,ontrol and the' H&V KEYSTONE mode elide

Note

_, If adjustments are made using both "H KEY-STONE" and "V KEYSTONE" at the same time,

the image aspect ratio may become slightlydistorted.

_,When adjusting "H KEYSTONE" and "V KEY-STONE" at the same time, the values of adjust-

able angles for each setting become smaller.• The adjustable value of the "V KEYSTONE"

becomes extremely small when "H KEY-STONE" is made to be the maximum value.

V On-screen display_ii /i

iii I

i I

Vertical Keystone Correction(Adjustment with A/_')

Horizontal Keystone Correction(Adjustment with _ / _-)

Q -35


Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. De-pending on the input signal, you can choose "STRETCH", "SIDE BAR", "CINEMA ZOOM" or "DOT

BY DOT (Computer input only)" image.

Press © RESIZE on the projector or GRESIZE on the remote control.

On the projector

RESIZE button

On the remote control

() RESIZE RESIZE button

i /r ' r _:

• "STRETCH" is fixed when 540R 720P or 10801 signals are entered.

Output screen image

DVD / Video STRETCH SIDE BAR CINEMA ZOOM

4801,480R 5761,576P, NTSC, PAL,

SECAM

Input Signal

Image type

4:3 aspect ratio

0 0

Letter box

° oo °ooomU mml.

Squeezed

16:9 aspect ratio

540R 720R 10801

16:9 aspect ratio

: Cutout area on which images cannot be projected.

(D -36

o(_o o(_omini mml.

O O O O

I

oQo 000Q Q 0 0

I

o(_o0 0

o0o u _,,= oQoo o o o

Input Signal Output screen image

Computer Imagetype

Resolution lower than ,,At-O/._

o -JcXGA

4:3 aspectratio

XGA O_Q_(1024 x 768)

4:3 aspectratio

STRETCH SIDE BAR CINEMA DOT BY DOTZOOM

-J1 I

o _ o OQO1280x720 o_o O O

16:9 aspectratio

: Cutout area on which images cannot be projected.

_Note

• You can select "CINEMA ZOOM" when with a "VGA/SVGA" signal with a vertical frequency 60 Hz

and less. However, when a "VGA/SVGA" signal with a vertical frequency of more than 60 Hz is used,"CINEMA ZOOM" is not available.

About Copyrights• When using the RESIZE function to select an image size with a different aspect ratio

to a TV program or video image, the image will look different from its original appear-ance. Keep this in mind while choosing an image size.

• The use of the Resize, Keystone Correction, Subtitle, or Overscan function to com-press or stretch the image for commercial purposes/public displays in a caf6, hotel,etc. may be an infringement of copyright protected by law for copyright holders. Pleaseuse caution.

, While watching non-widescreen images (4:3), if you use the RESlZE function to fillthe screen or use the Overscan function to change the aspect ratio of a fixed-ratioinput signal, parts of the outer edge of the image will be cut off or distorted. To watchoriginal images as the producers intended, set RESIZE to "SIDE BAR" and Overscanto its default setting.

i iI

J

iiii

Q -37

f_S ¸¸¸_¸__ _

'Operating with the Remote Control

,J,

Sh_ft_ng the Prejeeted 1tooage Vertically {_mag÷ Shift}

For easier viewing, this function shiftsthe entire image projected on thescreen up or down when projecting 16:9images from DVD players or other con-nected devices.

Press AIMAGE SHIFT.o The image moves up.

Press _IMAGE SHIFT.oThe image moves down.

Note

• The Image Shift function operates when"Resize" is not set to "DOT BY DOT".

_,For details on Image Shift, see page 47.

IMAGE IMAGE SHIFTSHIFT

buttons

®PICTUREMODEPICTURE

MODE button

IRIS IRIS button

FREEZE FREEZE bu_on

--(_)

Switeh_ng 1Lhe IHs Setting

This function controls the quantity ofthe projected light and the contrast ofthe image.Press (_IRIS." Each time the button is pressed while the dis-

play is on, the mode is switched in the follow-

ing order:HIGH BRIGHTNESS MODE -=====_MEDIUM MODE

LHIGH CONTRAST MODE J

Note

_,For details on Iris, see page 45.

Freezing a Mevin@ i_age

1 Press LC*FREEZE.

t_.o..,,; . _'The projected image is frozen.

Press _FREEZE again to return=" to the moving image from the cur-

/,._,_ rently connected device.

d_ -38

Semeeti_ the P_e_'e _e_e

You can select the appropriate picturemode to best match the projected im-age you are watching.

Press @PICTURE MODE," When pressing _PICTURE MODE, the picture

mode changes in the following order:

Standard ---* Natural---*Dynamic

tMemory _ Movie2 _ Movie1

Note

_*See page 43 for details on the picture mode.

Menu items

The following shows the items that can be set in the projector.The selectable items vary depending on the selected input, input signals, or adjustmentvalues. Items that cannot be selected will be greyed out.

PAGE 1

Picture Mode _ S_andard

Contrast [ O}[]- J] +r_

Bright i O }1__ _ + []

color l o}D- 1 +DTint ] O 11_- _ +_

Sharp [ O]_- _ +_

Red [

Blue l o/[] - , []

_ SEL./ADJ.

I_ RETURN _ ENTER_)END I

PAGE 2

Picture Mode @ Standard

BdlliantOolor TM [ 1 IIi5:1- _ +10-I

C. M. S.

Progressive @ 3D Progressive

DNR _ Level 1

IRIS _ High Brightness

Lamp Setting _ BdgM

'_'_'Reset

_ BEE/ADJ.

I_ *_ Single ADJ_)BND lRETURN

C. M.S. Saturation

C. M.S. Value

• "_ Reset

mBlrlYl

"_%SEL./ADJ.

I_ RETURN

o} m- _ []ol 8- +B

[] GI O;rl- ,rl[] c [ o; _- j +m[] B/ O1[] MI O/B- _m• "_ Reset

ENTER I(_END

Main menu

Picture

_" Page 43

Sub menu

Picture Mode _ Standard

l Natural

_Page 43 Dynam,cMovie1Movie2

Memory

Bright -30 _ +3O I

Colo_ -30 _ +301_2

Tint -30 _ +3O 1_2

Sharp -30 _ +3O 1_2

Red -30 _ +3O ]

Blue -30 _ +30 I

, Pagt43................I

CLR Temp _ r 5500K

l 6500K

"_Page 44 75®K8500K9300K10500K

BdllientColol TM [0/1/21 ]

_Page 43CMS ]"1

"_Page 44Progressive _[ 2D P_ogressEve

-1 3D Progressive"_ Page 44 n_mM,_e

DNR _ OFF

Leve_ I

_'Page 45 Level2Level3

IRIS _ High Bdghtf_essMedium Ivlode

'_Page 45 HighC°ntrast

Lamp Setting _ Bright

'_'Page 45 _ E_o+Qu_e_Reset I

[

:;%e,, ......,-30 _ +30 ]

"_Page 44 ] _c ....... IIc_s-w,_ I_ _t8 ....... I

Page 44 _ _qM ......."1 When a video signal, S-video signal, or component 4801/

5761 signal is input and the Progressive mode is set to "3D

Progressive" or "Film Mode", the C.M.S. function cannot beused.

*2 Item that cannot be set when inputting an RGB signalthrough INPUT 5 or INPUT 6.

ii

ii_i i

iii_il i

i_i! :

GO -39

Menu items (Continued)

Clock [ 011_1- +1_Phase ! 0 I m-_m

H Pos [ O ] _:_- +_

V-Pos / Ol_- +_

4,._ Reset

SpeCial Modes _ 1080]

Auto Sync _ On

I Cur. sig. freq : H 33.8 kHz / V 60 HZ I• _ SEL./ADJ. _ ENTER

I_ RETURN (_END I

, The "Fine Sync" menu is not available forINPUT 3 or INPUT 4.

Image Shiti / O 1D- _ +D

Overscan H ; O } r_l- _ +r_l

Oversoanv / olr'fl- +mSubtitle O] [_- +r_l

OSD Display P,2 On

Video System @ Auto

Signal Type _ Auto

HDMI Setting @ Standard

Background _ Blue

Auto Power Off _ On

rLamp Tirner(Ufe) [ O]h (100%) I

_* SEL./ADJ.

1_=4) _ ENTER(_END IRETURN

*_ Item that can be set when using INPUT 3 orINPUT 4.

-2 Item that can be set when using IINPUT 5 orINPUT 6.

PRJ Mode #2 Front

RS-232C @ 9600 bps

STANDBY Mode @ Eco

Fan Mode @ Norrnal

• ._ All Reset

Language @ English

%% SEL./ADJ. _ ENTER

I_ RETURN (_END I

Main menu

[ Firle Sync

'_'Page 46

Main menu

Option8

-_ Page 47

Main menu

options2

'_ Page 49

Sub menu

Cl_k -150 _ +150

•*Page 46Phase -30 _ +30

'_ Page 46H-POS -150 _ +150

"_ Page 46V-Pos -60 _ +60

•*Page 46Reset

-_ Speoia_Modes

_" Page 46Aut_ Sync IOn/Off]

"_ Page 46--_Cur sig feq I

.€'Page 46

Image Shift -24 _ +241

-_Page 47Ove_scar, H -30 _ +s0lOre scar, v -30 _ +30J

_Page 47SubtitFe .30 _ +30]

._ Page 47OSD Display [On/Off] ]

,_ Page 48Video System

,,_Page 48

Sub menu

]_Auto NTSC 358

PAL PAL-M

SECAM PAL-N

NTSC443 PAL-60

S_gnaFType

,,_Page 48

HDM] Setting

,,* Page 48

Background _1 B_ue_Page 48 .oneAuto Power Off [On/Of f] 1

,,_Page 49--_ Lamp TirTer(Ufe) I

,,_Page 49Sub menu

PRJ Mode

_Page 49

RS-23#C

=_Page 50STANDBY Mode

'_ Page 50Fan Mode

'_ Page 50A]FReset 1

_' Page 50--_ Language _ English Sven_ka

Page 50 I Espa_olDeutsoh_P°dugu6s

Nederlands fNFrancais H _,;*Italiano

(_ -40

'_ Using the Menu Screen

ENTER button

Adjustment buttons (J,/V/,,q/)-)

MENU button

Adjustment buttonsI i_/ (A/v/,(/)-)

_,,,;, MENU MENU button

(_)/ ,

ENTER ENTER button

b®RETURNRETURN button

/ @./ o Press ,._RETURN to re-

turn to the previous• screen when the menu

is displayed

Example: Adjusting "Bright".• This operation can also be performed by using the buttons on the projector.

Press (=_MENU.1.The- "Picture" menu screen for the se- modeEXample:"Picture" screen menu for INPUT 1

l_ leered input mode is displayed.%/

2 Press I_ or 4 to select the menu; icon to adjust.

.)The selected icon is highlighted.Menu icon Menu screen

Picture

_) Fine Sync

Options1

Options2

%Note

,, The "Fine Sync" menu is not availablefor INPUT 3 or INPUT 4.

Picture Mode

Contrast

BrightColor

Tint

SharpRed

Blue

Selected input mode

Menu [cons

(D -41

Using the Menu Screen (Continued)

3 Press A or _' to select the item toadjust.

" The selected item is highlighted.i

i

ii

Te adjust the prejeetedimage while watching itPress (_)ENTER.=The selected item (eg "Bright") is dis-

played by itself at the bottom of thescreen.

• When pressing ,L or 'V',the following item("Color" after "Bright") will be displayed.

Press (_ENTER again to return to the

previous screen.

4" Press ,q or I_ to adjust the itemselected.* The adjustment is stored.

i

Piclure Mode _ Standard

Contrast [ 0 ] [] - + []

Color [ o1[]- +[]Tint [ 0 ] [] - + []

Sharp [ 0][]- +[]

Red [ o][]- +[]Blue [ o}E]- +[]

•_" SEL./ADJ.l_m_ __ISingle ADJRETU RN (_ END

Items to be adjusted

I The item displayed by itself I

(_END

Picture Mode _ Standard

Contrast [ 0 ] []- J_ + []

Color [ 0]D- _ +DTint [ O][]- j +[]

Sharp [ O][]- J_ +r_

Red [ 0][]- J +[]

Blue [ sir-I- _ +[]

"_ SEE/ADJ.I_ RETURN "_ Single ADJ_)END I

Note

_*The _ MENU button does not function while the projector is operating the "Auto Sync" or "FREEZE"functions.

(D -42

Picture Adjustment ("Picture" menu)

PAGE 1

- _Picture Mode

_Contrast

Bright

Color

_2_- TintSharpRedBlue

Standard

o1[] - _[]olD- J +Do',•- II +Do[]- 11 +DoI [] - +[]o []- +[]o]•- j +_

PAGE2

_Z

®--5-

Menu operation 4 Page 41

Picture Mode @ Standard

= Bri]liantColor TM I 1 l[]- _ +[]

mC. M. S.

=Progressive _" 3D Progressive

=DNR _ Level 1

=IRIS _ High Brightness

=Lamp setting _" Bright

• ,_ Resel

_ iI

U

Selectableitems

Standard

Natural

Dynamic

Movief

The default settings of each item when selecting Picture ModeDescription

For standard image

A balanced color itr_ageis obtained.

A vivid image is obtained.

Makes the black levels of the

dark portions of the screenmore pronounced and vivid.

Reduces glare and creates asubdued tone.

Allows you to store your pictureadjustment setiings. The settingsstored effect each input mode.

CLR Temp BrilliantColor Tr_ IRIS Lamp Setting

7500K 0 High Brightness Bright



6500K 0 High Brightness Eco + Quiet

Movie2 6500K 0 Medium Mode Eco + Quiet

Memory 7500K 0 High Brightness Bright

_"You can set or adjust each item in the "Picture" menu to your preference Any changes you make are retained in memory

Note ,. You can also press (_ PICTURE MODE on the remote control to select the picture mode.

(See page 38.)

Adjustment items _ button I_ button

Contrast For less contrast. For more contrast.

Bright For less brightness. For more brightness.

Color *_ For less color intensity. For more color intensity.

Tint *_ For making skin tones purplish. For making skin tones greenish.

Sharp *_ For less sharpness. For more sharpness.

Red For weaker red. For stronger red.

Blue For weaker blue. For stronger blue.

BrilliantColor TM*_ For making the effect weaker. For making the effect stronger.

*_ Item that cannot be adjusted in RGB mode..2 BrilliantColorTM uses Texas Instruments' BrilliantColor TM technology. As the BrilliantColor TM level is increased,

the k'nage becomes brighter while the color reproduction is kept at a high level.

Note _,To reset all adjustment items, select "Reset" and press (_ENTER. The Picture Mode

settings of the selected input return to the default settings.

(D -43

Picture Adjustment ("Picture" menu) (Continued)

Selectableitems Description

5500K For lower color temperature for6500K warmer, reddish incandescent-like

7500K images.8500K9300K

10500K For higher color temperature forcooler, bluish, fluorescent-like images.

Note

_'Values on "CLR Temp" are only for generalstandard purposes.

Select "C.M.S." (Color Management System) inthe "Picture" menu and then press @ ENTER.

This function adjusts each of the six main colorsthat comprise the color wheel, altering their"Hue", "Saturation", or "Value".

Selectable items Description

C.M.S.-Hue Sets the hue of the main colors.

C.MS.-Saturation Sets the saturalion of the main colors

C.M.S.-Value Sets the brightness of the main colors.

Reset The adjustments of "Hue","Saturation" and "Value" of all colors

are reset to the default setting.

Adjusting "Hue", "Saturation", or "Value".

1 Press _. or T to select either "Hue", "Saturation", or

"Value" and then press _0 ENTER.2Select the color to be adjusted with _. or V and

adjust it with _ or _.

Example of adjusting the "Hue"

Main colors _1 button _- button

R (Red) Closer to magenta Closer to yellow

Y (Yellow) Closer to red Closer to green

G (Green) Closer to yellow Closer to cyan

C (Cyan) Closer to green Closer to blue

B (Blue) Closer to cyan Closer to magenta

M (Magenta) Closer to blue Closer to red

0 -44


• When "Saturation" is selected, the selectedcolor becomes4 : lighter. D,-: thicker.

- When "Value" is selected, the selected colorbecomes

: darker. _ : brighter.

- To reset the adjustment values of each colorto the default settings, select "Reset" and pressC_ ENTER.

mnfo

• When a video signal, S-video signal, or compo-nent 480[/576[ signal is input, set "Progressive"

mode to "2D Progressive" and then adjust thecolors.


2D Useful to display fast-moving imagesProgressive such as sports.

3D Useful to display relatively slow-Progressive moving images such as drama and

documentary more clearly.

FilrT_Mode Reproduces the image of film source*

clearly. Displays the optimized image offikT_transformed with three-two pull down(NTSC and PAL6OHz) or two-two pulldown (PAL5OHz and SECAM) enhance-ment to progressive mode images

The film source is a digital video recording with theoriginal encoded as is at 24 frames/second. Theprojector can convert this film source to progres-sive video at 60 frames/second with NTSC andPAL6OHz or at 50 frames/second with PAL5OHzand SECAM to play back a high-definition image.

Note

_, In NTSC or PAL6OHz, even if the 3D Progres-

sive mode has been set, the three-two pulldown enhancement will be enabled automati-

cally when the film source has been entered._, When the image is blurred or noisy, switch to

the optimal mode._, When using progressive inputs, inputs are di-

rectly displayed so that 2D Progressive, 3DProgressive and Film Mode cannot be selected.

mnfo

4, The settings can be made either when INPUT3or INPUT4 are selected or when INPUT1, 2,

INPUT5, or INPUT6 are selected and the in-

put signal is 4801 or 576|.

Videodigitalnoisereduction(DNR)provideshighqualityimageswithminimaldotcrawlandcrosscolornoise.Selectableitems DescriptionOFF DNRdoesnotfunction.Level1-3 SetstheDNRlevelforviewing

aclearerpicture.

NoteSet "DNR" to "OFF" in the following cases:

* When the image is blurry.o When the contours and colors of moving im-

ages drag.o When TV broadcasts with weak signals are

projected.


This function controls the quantity of the pro-jected light and the contrast of the image.


High Brightness High brightness is givenpriority over high contrast.

Medium Mode Intermediate mode between

high contrast and highbrightness.

High Contrast High contrast is given priorityover high brightness.

Note

• You can also use @ IRIS on the remote con-

trol to change the Iris. (See page 38.)

PowerSelect-

able Bright- Fan consumption Lamp Lifeitems ness sound (When using

AC 100V)

Bright 100% Normal 355W Approx.2,000hours

Eco + Approx. Low 310W Approx.Quiet 87% 3,000

hours

Note

• When "Lamp Setting" is set to "Eco+Quiet",the power consumption will decrease and the

lamp life will extend. (Projection brightness

decreases approximately 13%.)

Q -45

Computer image Adjustment("Fine Sync" menu)

®-®=

"ClockPhase e_- _ +_H-Pos 0 ] _I-

V-Po_ oII_- J +__'_ Rese[

=Special Modes c:_ 10801

=Auto Sync _ On

Cur. sig. freq : H 33.8 kHz / V 60 Hz ]

Use the Fine Sync function in case of irregulari-ties such as vertical stripes or flickering in por-tions of the screen.


Clock Adjusts vertical noise.

Phase Adjusts horizontal noise (similarto tracking on your VCR).

H-Pos Centers the on-screen imagebymoving it to the left or right.

V-Pos Centers the on-screen imagebymoving it up or down.

Note

• You can automatically adjust the computerimage by setting "Auto Sync" in the "FineSync" menu to "On" or pressing ©3 AUTOSYNC on the remote control.

• "Clock". "Phase", "H-Pos" and "V-Pos" can-not be adjusted when INPUT 6 is selected.

.The adjustable area of each item may bechanged according to the input signal.

• To reset all adjustment items, select "Reset"and press (2 ENTER.

Menu operation _ Page 41

Ordinarily, the type of input signal is detectedand the correct resolution mode is automaticallyselected. However, for some signals, the opti-mal resolution mode in "Special Modes" in the"Fine Sync" menu may need to be selected tomatch the computer display mode.

Note

• Avoid displayhg computer patterns whichrepeat every other line (horizontal stripes).(Flickering may occur, making the image hardto see,)

o Information on the currently selected input sig-nal can be confirmed in item _.


On Auto Sync adjustment willoccur when the projector isturned on or when the inputsignals are switched, whenconnected to a compute£

Off Auto Sync adjustment is notautomatically performed.

Note

• Auto Sync adjustment is also performed by

pressing (,_ AUTO SYNC on the remote con-trol.

• The Auto Sync adjustment may take some timeto complete, depending on the image of the

computer connected to the projector.,_ When the optimum image cannot be achieved

with Auto Sync adjustment, use manual ad-justments.

This function allows you to check the current in-put signal information.

(D -46

Using the "Options" Menu

t;_Tlmage Shift [_,Toversoan H [2 T°verscan v [ o ITI-+[]

_4"=Toso Display(_= =T= Video Systera @ Auto(6)--SignaIType @ Auto

{_ +HDMI Setting @ S_andard

_,=TB_okgrouod e Blue{9:.--Auto PowerOff @ Ond0:_lLamp Timer(Life) 0]h 1100%)I

= _ = = Oe = / =

You can move the projected image vertically.

button /" _- button

Note

• The Image Shift function cannot be selectedwhen "Resize" is set to "DOT BY DOT".

-,You can also use the IMAGE SHIFT buttons

on the remote control to adjust the image po-sition.

This function allows you to adjust the Overscanarea ratio (display area ratio).

Orientation _1 button _- button

Overscan H Reduces the Enlarges the

(Horizontal) image, image.(The display (The display area

Overscan V area ratio ratio becomes

(Vertical) becomes larger.) smaller.)

Note

• This function can only be adjusted when avideo, S-video, or Component signal is input.

_*If the display area ratio is set too large, noisemay appear at the screen edges. If this hap-

pens, set the display area ratio to a smaller value.,When "mesize" is set to "CINEMA ZOOM",

depending on the input signal, "Overscan V"may not be adjustable.

• Also read "About Copyrights" on page 37.

With this function, you can adjust the vertical size

of the display to allow for subtitles.

_1 button The image is compressed by adjustingthe vertical size of the display.

button The image is enlarged by adjusting thevertical size of the display.

Note

_*When changing the screen with the Subtitle set-ting, not only the bottom of the screen rises, but

also the upper part is changed to a certain point.• The Subtitle setting can be adjusted more ef-

fectively with the Overscan and Image Shiftfunctions.

_, The Subtitle setting only works when "Resize"is set to "CINEMA ZOOM".

_*The adjustment area changes according to theinput signal.

(D -47

usingthe "options" Menu(continued)

Menu operation -€ Page 41


On All On-screen Displays are displayed.

Off INPUT/FREEZE/AUTO SYNC/RESIZE/PICTURE MODE/IRIS are netdisplayed.

This function can only be set in INPUT 3 orINPUT 4.

The video input system mode is factory presetto "Auto";however, a clear picture from the con-nected audio-visual equipment may not be re-ceived, depending on the video signal difference.In that case, switch the video signal.


PAL When connected to PAL videoequipment.

SECAM When connected to SECAMvideo equipment.

NTSC4.43 When reproducing NTSCsignals in PAL video equipment.

NTSC3.58 When connected to NTSC videoequipment.

This function allows you to select the input sig-

nal type (RGB or Component) for INPUT 5 orINPUT 6.


Auto Automatically selects theappropriate input signal

between RGB and Component.

RGB Set when RGB signals arereceived.

Component Set when component signalsare received.

Note

o You can also select "Signal Type" using CORGB/COMP. on the remote control (INPUT 5or INPUT 6).

When there is an HDMI-capable device con-nected to INPUT 6, an optimum picture may notbe displayed if the device's output signal typeand the projector's input signal type do not match.If this should occur, switch the HDMI Setting.


Standard

Enhanced

When the black levels of the

image show banding or appearfaded, select the option thatresults in the best picturequality. (In most circumstances,"Standard" should be selected.)

Note

o The HDMI Setthg can be selected only whenINPUT 6 is selected.


Blue Blue screen

None (Black screen)

O -48


On When no input signal is detected formore than 15 minutes, the projector will

automatically enter standby mode.

Off The Auto Power Off function will bedisabled.

Note

oWhen the Auto Power Off function is set to

"On", 5 minutes before the projector entersstandby mode, the message "Enter STANDBY

mode in X min." will appear on the screen toindicate the remaining minutes.

You can confirm the cumulative lamp usage timeand the remaining lamp life (percentage).

Lamp usage condition

"Life"

Operated exclusively

with Lamp Setting set to"Eco + Quiet"

Operated exclusivelywith Lamp Setting set to"Bright"

Remaining lamp life

100% 5%

Approx. Approx.3,000 150 hourshours

Approx. Approx.2,000 100 hourshours

Note

o It is recommended that the lamp be changedwhen the remaining lamp life becomes 5%.

• The lamp life may vary depending on the us-age condition.


PRJ Mode %_' Front

-RS-2320 _ 9600 bps

-STANDBY Mode _ Eco

-Fan Mode _' Normal

- _,4, All Reset

-Language @ English


Front Normal image (Projected fromthe front of the screen)

Ceiling + Front Inverted image (Projectedfrom the front of the screen

with an inverted projector)

Rear Reversed image (Projectedfrom the rear of the screen or

with a mirror)

Ceiling + Rear Reversed and inverted image(Projected with a mirror)

See page 19 for details of Projection (PRJ) Mode.

i _ iii ii

i_ _iii_

(D "49

Using the "Options" Menu (Continued)

Make sure that both the projector and computerare set for the same baud rate.


9600bps Transmission speed is slow.

115200bps Transmission speed is rapid.

Menu operation --_ Page 41

This function changes the fan rotation speed.


Normal Suitable for normal environments.

High Select this when using the projector ataltitudes of approximately 4,900 feet(1,500 meters) or more.

When "Fan Mode" is set to "High", the fan rotationspeeds up, and the fan noise becomes louder.

When "STANDBY Mode" has been set to "Stan-dard", the RS-232C function is activated andpower is consumed even in standby mode. It isrecommended that "STANDBY Mode" be set to

"Eco" when it is not being used. This reducespower consumption when the projector is instandby mode.


Standard The RS-232C function is

activated even if the projector isin standby mode.

Eco The RS-232C function is

switched off when the projectoris in standby mode.

Note

• When you want to control the projector usingthe RS-232C function, set to "Standard".

Use "All Reset" to initialize all the adjustmentsyou have made to the default settings.

Note

The following items cannot be initialized.* "Fine Sync" menu

- Special Modeso "Options1" menu

Lamp Timer (Life)Language

The projector can switch the on-screen displaylanguage among 11 languages.

English SvenskaDeutsch Portugu_sEspafiol _Nederlands _, 04Fran_ais Ii 4_:_{_Italiano

(D -50

( Maintenance

Cleaning the projector

[] Ensure that you have unplugged the powercord before cleaning the projector.

[] The cabinet as well as the operation panel ismade of plastic. Avoid using benzene or

thinner, as these can damage the finish on thecabinet.

[] Do not use volatile agents such as insecticideson the projector.Do not attach rubber or plastic items to the

projector for long periods.

The effects of some of the agents in the plasticmay cause damage to the quality or finish of theprojector.

[] Wipe off dirt gently with a soft flannel cloth.[] When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring thecloth well and then wipe the projector.

Strong cleaning detergents may discolor, warp

or damage the coating on the projector. Makesure to test on a small, inconspicuous area onthe projector before use.

!

4,

Cleaning the lens

[] Use a commercially available blower or lenscleaning paper (for glasses and camera lenses)

for cleaning the lens. Do not use any liquid typecleaning agents, as they may wear off the

coating film on the surface of the lens.[] As the surface of the lens can easily get

damaged, be sure not to scrape or hit the lens.

f-

Cleaning the exhaust and intake vents[] Use a vacuum cleaner to clean dust from the

exhaust vent and the intake vent.

)

Info

4, If you want to clean the air vents during pro-

jector operation, be sure to pressG STANDBY/ON on the projector or

(_STANDBY on the remote control and put the

projector into standby mode. After the cool-ing fan has stopped, clean the vents.

(D -51

! iii

Maintenance indicators

[] The warning lights (power indicator, lamp indicator and temperature warning indicator) on theprojector indicate problems inside the projector.

[] If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminatered, and the projector will enter standby mode. After the projector has entered standby mode,follow the procedures given below.

L_ T,_ [ Temperature warning indicator

Q j__ Lamp indicator

_G_ Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location"_" will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp

will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec=

tot will enter standby mode. After "_" appears, be sure to perform the measures described on page53.

About the lamp indicator

[] When the remaining lamp life becomes 5% or less, #!! (yellow) and "Change The Lamp" will bedisplayed on the screen. When the percentage becomes 0%, it will change to W (red), the lamp wil

automatically turn off and then the projector will automaticaNy enter standby mode. At this time, thelamp indicator will illuminate in red.

[] If you try to turn on the projector a fourth time without replacing the lamp, the projector willnot turn on.

Indicators on the Projector

Power indicator

Lamp indicator

Temperature warningindicator

Red on

Green on

Red blinks

Green blinks

Green on

Green blinks

Red on

Off

Red on

Normal (Standby)

Normal (Power on)

Abnormal (See page 53.)

Normal (Cooling)

Normal

The lamp is warming up or shutting down.

The lamp is shut down abnormally orrequires to be changed. (See page 53.)

Normal

The internal temperature is abnormallyhigh. (See page 53.)

(D -52

Tempera-ture

warningindicator

Lampindicator

Maintenance indicator

Normal Abnormal

Off Red on

(Standby)

Green on Red on(Greenblinks

when the

lamp iswarming

up orturning Red on

off.) (Standby)

Problem

The internal

temperature isabnormallyhigh.

The lamp doesnot illuminate.

Time to changethe lamp.

The lamp doesnot illuminate.

Cause

• Blocked air intake

• Cooling fan •breakdown

• Internal circuitfailure

• Clogged air intake

• The lamp is shut •down abnormally.

• Remaining lamp life •becomes 5% orless. •

• Burnt-out lamp• Lamp circuit failure

e

Power Green on/ Red The power - The lamp unit cover •indicator Red on blinks indicator blinks is open.

Green in red when theblinks projector is on.

(Cooling)

Possible Solution

- Relocate the projector toan area with properventilation. (see page 8)

Take the projector to yournearest Authorized

SharpVision Service Centeror Dealer for repair.

Disconnect the power cordfrom the AC outlet, and

then connect it again.

Carefully replace the lamp.(See page 55.)Take the projector to yournearest AuthorizedSharpVision Service Center

or Dealer for repair.Please exercise care when

replacing the lamp.Securely install the cover.

If the power indicator blinksin red even when the lamp

unit cover is securelyinstalled, contact yournearest Authorized

SharpVision Service Centeror Dealer for advice.

mnfo

_, If the temperature warning indicator illuminates, and the projector enters standby mode, follow thepossible solutions above and then wait until the projector has cooled down completely before plug-ging in the power cord and turning the power back on. (At least 10 minutes.)

_, If the power is turned off for a brief moment due to power outage or some other cause while using

the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,

replace the power cord in the AC outlet and then turn the power on again._,The cooling fan keeps the internal temperature of the projector constant and this function is con-

trolled automatically. The sound of the cooling fan may change during operation because the fan

speed may change and this is not a malfunction.

• Do not unplug the power cord after the projector has entered standby mode and while the coolingfan is running. The cooling fan runs for about 90 seconds.

(_D-53

Regarding the Lamp

Lamp[] It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life(percentage) can be checked with the on-screen display. (see page 4,9)

[] Purchase a replacement lamp of type AN-100LP from your place of purchase, nearest AuthorizedSharpVision Service Center or Dealer.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limitedwarranty. All service of this projector under warranty, including lamp replacement,must be obtained through an Authorized SharpVision Service Center or Dealer. Forthe name of the nearest Authorized SharpVision Service Center or Dealer, pleasecall toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp DisposalInformationwww.lamprecycle.org or 1-800-BE-SHARP [U.S.A.ONhVl

Cautien Ceneeming the Lamp[] This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surfacescratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the conditionand the frequency of use. It is important to note that failure can often result in the bulb cracking.

[] When the lamp replacement indicator and on-screen display icon are illuminated, it is recommendedthat the lamp be replaced with a new one immediately, even if the lamp appears to be operating

normally.[] Should the lamp break, there is also a possibility that glass particles may spread inside of the

projector. In such a case, it is recommended you contact your nearest Authorized SharpVision ServiceCenter or Dealer to assure safe operation.

[] Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in thelamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes

mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In caseof exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp" Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may

cause burn or injury.

[] Carefully change the lamp by following the instructions described in this section. * if you wish,you may have the lamp replaced at your nearest Authorized SharpVision Service Center orDealer.

* If the new lamp does not light after replacement, take your projector to the nearest AuthorizedSharpVision Service Center or Dealer for repair.

(D -54

Removing and In÷tailing theLamp Unit

Warning!The lamp unit becomes very hot while the pro-jector is operating. Do not remove the lamp

unit from the projector right after use.The lampand parts around the lamp will be very hot and

may cause burns or injury.

mnfo

Make sure that you remove the lamp unit by

the handle. Do not touch the glass surface ofthe lamp unit or the inside of the projector.

To avoid injury to yourself and damage to thelamp, be sure to carefully follow the stepsbelow.

Do not loosen other screws except for thelamp unit cover and lamp unit.

Press QSTANDBY/ON on the pro-jector or _STANDBY on the re-mote control to put the projectorinto standby mode.

Waituntil the cooling fan stops.

Lamp unitAN-100LP

STANDBY/ON button

AC socket

_. [_ L_Sre[a_ervice screw( purl t cover)

iiii

i i i

i i

ii

i_ill i

I

(_D-55

Regarding the Lamp (Continued)

l Remove the lamp unit.,, Loosen the securing screws from the

lamp unit. Hold the lamp unit by the

handle and pull it in the direction of thearrow. At this time, keep the lamp unit

hor zonta and do not t t t.

5 Insert the new lamp unit.

Press the lamp unit firmly into the lampunit compartment. Fasten the securing

screws.

%j//

Replace the lamp unit cover.• AEign the tab on the lamp unit cover (1)

and place it while pressing the tab (2)to close it. Then tighten the user service

screw to secure the lamp unit cover.

Info• If the lamp unit and lamp unit cover are

not correctly installed, the power will notturn on, even if the power cord is con-nected to the projector.

Resettimg l_he Lamp Time_'

Reset the lamp timer after replacing the lamp.

Handle

Securing screws

®

AC

(B -56

Reset the lamp timer.

While simultaneously holding downGMENU, QENTER and _' on the pro-jector, press _STANDBY/ON on the pro-

jector.

"LAMP O000H" is displayed, indicatingthat the lamp timer is reset.

,. o I I STANDBY/ON

........ _/F '_" %`" button

ENTEBbutton_---"_ MENU button

T button

Connecting Pin Assignments

COMPUTER-RGB/COMPONENT INPUT5 Terminai: 15-pin Mini D-sub female

C©MPUTER-RGB Input1. Video input (red)

11 ,_ 15

6 _ 10

2. Video input (green/sync on green)3. Video input (blue)4. Not connected5. Not connected6. Earth (red)7. Earth (green/sync on green)8. Earth (blue)9. Not connected10. GND11. Not connected12. Bi-directional data

13. Horizontal sync signal: TTL level14. Vertical sync signal: TTL level15. Data clock

RS-232CTerminab 9-pin Mini DIN female connector

8 Pin No. Signal Name

9 7 2. RD Receive Data

3. SD Send Data4.

6 ................. 3 5. SG Signal Ground6.

7. RS Request to Send5" 8. CS Clear to Send

9.2 1

ii ii ii il

iil iii /

iilliil l i

connector

Component Input1. PR (CR)

2. Y

3. PB (CB)4. Not connected5. Not connected6. Earth (PR)7. Earth (Y)8. Earth (PB)9. Not connected10. Not connected11. Not connected12. Not connected13. Not connected

14. Not connected15. Not connected

I/0 Reference

Not connectedInput Connected to internal circuitOutput Connected to internal circuit

Not connected

Connected to internal circuitNot connectedConnected to CS in internal circuitConnected to RS in internal circuitNot connected

RS-232CTerminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor(optional accessory: AN-A1 RS)

Pin No. Signal I/01.

InputOutput

Name

1 --- 5 2. RD Receive Data

__'] 4.3 SD Send Data5. SG Signal Ground6.

7. RS Request to Send6 .. 9 8. CS Clear to Send

9.

Reference

Not connectedConnected to internal circuitConnected to internal circuitNot connectedConnected to internal circuitNot connected

Connected to CS in internal circuitConnected to RS in internal circuitNot connected

RS-232C Cable recommended connection: 9-pin D-sub female connector

Pin No. Signal Pin No. Signal1. CD 1. CD

5 ,.. 1 2. RD 2. RD

4. ER 4. ER5. SG 5. SG6. DR _ 6. DR

7. RS7. RS _ 8.9 .. 6 8. CS _- CS9. CI 9. CI

4

Note

,* Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on thecontrolling device (e.g. computer).

Projector ComputerPin No. Pin No.

56

(D -57

_ Connecting Pin Assignments (Continued)

HDIVll Terminal1 19

2 18

Pin No. Name Pin No. Name Pin No. Name1. TMDS Data2+ 8. TMDS Data0 Shield 14. Reserved2. TMDS Data2Shield 9. TMDS Data0- 15. SCL3. TMDSData2- 10. TMDSCIock+ 16. SDA4. TMDS Data1+ 11. TMDS Clock Shield 17. DDC/CEC Ground5. TMDS Data1 Shield 12. TMDS Clock- 18. +5V Power

6. TMDS Data1- 13. CEC 19. Hot Plug Detect7. TMDS Data0+

RS=232C Specifications and Command Settings

Cemputer e@ntrelA computer can be used to control the projector by connecting an RS-232C serial control cable

(cross type, sold separately) to the projector, (See page 27 for connection,)

Cemmunieatien eenditionsSet the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: NoneBaud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None• Set the projector's baud rate to the same rate as used by the computer.

Basic fermatCommands from the computer are sent in the following order: command, parameter, and return code.After the projector processes the command from the computer, it sends a response code to the computer.

Command format

Command 4=digit Parameter 4=digit

Response Normal response

code format _ [ Return code (0DH) ]

Problem response(communication error or incorrect command

IEIRIRII Return code (0DH)

InfoWhen controlling the projector using RS=232C commands from a computer, wait for at [east 30seconds after the power has been turned on, and then transmit the commands.

• When more than one code is being sent, send each command only after the response code for the

previous command from the projector is verified.

CemmandsExample: When turning on the Computer Projector

pr°ject°r'maketheIPIOIWI I-I-I-I' --IOlKl lfollowing setting.

PowerOffPowerOn

iNPUT1(Video1:Component1)

iNPUT2(Video2:Component2)iNPUT3(Video3:S-Video}

iNPUT4(Video4:Video)iNPUT5(RGB1: RGS/Oomponent}

iNPUT6(RGB2: RG_/Oomponel]t}

d_ -58

V OKo_ERR

v OKoiERR

v _: oi Er4R

V _: oi Er4R

Note

_,If an underbar (_) appears in the parametercolumn, enter a space.

Computer Compatibility Chart

.. Multiple signal support ,, Compatible with sync on green signalHorizontal Frequency: 15-70 kHz, ,, Expansion System resizing technologyVertical Frequency: 45-85 Hz,Pixel Clock: 12-85 MHzSync signal: Compatible with TTL level

The following is a list of modes that conform to VESA. However, this projector supports othersignals that are not VESA standards.

27.0

640 x 350 31.5

37.5

27.0

640 x 400 31.537.9

27.0720 x 350

31.5

VGA 27.0720 x 400 31.5

34731262379564o×4_0 37.937.5

43.3

31.435.1

37.9

SVGA 800 x 600 46.6

48.1

46.9

53.740.3

XGA 1,024 x 768 48.456.5

60.0

1,280 x 720 45.0

1,280 x 768 47.8

VGA 640 x 480 34.9

swA 800×600 378832 x 624 49.7

XGA 1,024 x 768 60.2

60

70

85

6070

85

60

70

6070

85

50

6070

72

75

85

5056

60

70

72

7585

50

60

70

7560

60

67

60

7575

v"

v"

v"

v"

v"

v"

Upsca_e

T_ue

Upscale

T_ue

Note

When this proEector receives 640 × 350 VESA format VGA signals, "640 × 400" appears on the screen.

Signal

48nl

48oP

54oP

5761

576P

72oP

10351

10351

10801

10801

Horizontal Frequency (kHz) Vertical Frequency (Hz) HDMI Support

157 60 ¢

31 5 60 ¢

338 60

156 50 ¢

31 3 50 ¢

450 60 ¢

281 50

338 60

281 50 ¢

338 60 ¢

Q -59

Tf roubles.ooting

Problem

Picure does not appearor projector does not

start.

No picture appears (orpicture is dark).

Color is faded or poor.

Picture is blurred;

noise appears.

Picture is green onINPUT 5 (Component)/INPUT 6 (Component).

Picture is pink (no green)on INPUT 5 (RGB)/INPUT

6 (RGB).

An unusual sound is

occasionally heard fromthe cabinet.

Check Page

Projector power cord is not plugged into the wall outlet. 28

Power to the external connected devices is off.

The selected input mode is wrong. 29

Cables incorrectly connected to the projector. 23-27

Remote control battery has run out. 14

External output has not been set when connecting notebook 26computer.

The lamp unit cover is not installed correctly. 55, 56

Cables incorrectly connected to the projector. 23-27

"Bright" is set to minimum position. 43

Depending on the computer you are using, an image may not beprojected unless the signal output setting of the computer isswitched to the external output. Refer to the computer's operationmanual for how to switch its signal output settings.

Image adjustments are incorrectly set. 43Make adjustments to "Color", "Tint" and "BrilliantColor TM"in "PictureMode".

',Video Input only) 48Video input system is incorrectly set.

Adjust the focus. 30

The projection distance exceeds the focus range. 20

There is fog on the lens. If the projector is carried from a cold room -into a warm room, or if it is suddenly heated, condensation may formon the surface of the lens and the image will become blurred. Pleaseset up the projector at least one hour before it is to be used. Ifcondensation should form, remove the power cord from the walloutlet and wait for it to clear.

',Computer Input only)

Perform "Fine Sync" Adjustments ("Clock" Adjustment) 46

Perform "Fine Sync" Adjustments ("Phase" Adjustment) 46

Noise may appear depending on the computer.

Select "Signal Type" in the "Options1" menu and change the inputsignal type.

48

If the picture is normal, the sound is due to cabinet shrinkagecaused by room temperature changes. This will not affect operationor performance.

Maintenance indicator on See "Maintenance Indicators". 52the projector illuminates

or blinks in red.

O -60

Problem Check Page

image adjustments are incorrectly set. 43

Select the HDMI Setting ("Standard" or "Enhanced") that results in 48

the best picture quality.

52, 55

Picture is too bright andwhitish.

The black levels of the

image show banding orappear faded wheniNPUT 6 is selected.

The cooling fan becomes

noisy.

The lamp does not lightup even after the

projector turns on.

The lamp suddenly turnsoff during projection.

The image sometimesflickers.

The lamp needs muchtime to turn on.

Picture is dark•

The remote controlcannot be used•

When temperature inside the projector increases, the cooling fanruns faster•

The lamp indicator is illuminating in red.Replace the lamp.

Cables incorrectly connected to the projector or the connected 23-27equipment works improperly.If this happens frequently, replace the lamp. 55

The lamp will eventually need to be changed• 55While the remaining lamp life draws to a close, replace the lamp.

Operate the remote control while pointing it at the projector's remotecontrol sensor.

The remote control may be too far away from the projector• 15if direct sunlight or a strong fluorescent light is shining on theprojector's remote control sensor, place the projector where it will notbe affected by strong light.

The batteries may be depleted or inserted incorrectly. Make sure thebatteries are inserted correctly or insert new ones. 14

This unit is equipped with a microprocessor, its performance could be adversely affected by incorrect operationor interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

'Service Information (For the U.S.)

For the location of the nearest Authorized SharpVision Service Center, or to obtain productliterature, accessories, supplies or customer assistance, please call 1-800-BE-SHARP (1-800-237-4277) or visit SHARP's website (http://www.sharpusa.com).

_jF

(_D-61

Specifications

Product typeModel

Video system

Display methodDMD panel

Lens

Projection lampComponent input signal

(INPUT1/2)

S-video input signal(INPUT 3)

Video input signal(INPUT 4)

Computer RGB/Component input signal

(INPUT5)

HDMI input signal(INPUT 6)

Horizontal resolution

Vertical frequencyHorizontal frequency

Pixel clockRS-2320 terminalTRIGGER terminal

Rated voltageInput current

Rated frequencyPower consumption

Powerconsumption(standby)Heat dissipation

Operating temperatureStorage temperature

Cabinet

I/R carrier frequencyDimensions (approx.)

Weight (approx.)Replacement parts

ProjectorXV-Z3000NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV4801/DTV480P/DTV540P/DTV5761/DTV576P/DTV720P/DTV1035I/DTVl 0801/DTV1080][-50

Single Chip Digital Micromirror Device TM (DMD TM) by Texas InstrumentsPanel size: 0.65", 1chip DMDDrive method: Digital Light Processing (DLP TM)

No. of dots: 983,040 dots (1280 [H] x 768 [V])1-1.15 x zoom lens, F2.4-2.6, f = 19.0-21.9 mm275 W DO lampRCA connector

Y: 1.0 Vp-p, sync negative, 75 _ terminatedPB (CB): 0.7 Vp-p, 75 _ terminatedPR (CR): 0.7 Vp-p, 75 _ terminated4-pin mini DIN connectorY (luminance signal): 1.0 Vp-p, sync negative, 75 _ terminatedC (chrominance signal): Burst 0.286 Vp-p, 75 _ terminatedRCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 _terminated

15-pin mini D-sub connectorRGB separate/sync on green type analog input: 0-0.7 Vp-p, positive, 75 _zterminatedHORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)VERTICAL SYNC. SIGNAL: Same as above

HDMI terminal (video signal only)

720 TV lines (DTV720P)45-88 Hz15-70 kHz12-88 MHz

9-pin mini DIN connectorPower jack: DC 12V outputAC 100-240 V3.7A50160 Hz

355 W (Lamp Setting 'Bright")/310 W (Lamp Setting "Eco + Quiet") with AC 100 V340 W (Lamp Setting 'Bright")/300 W (Lamp Setting "Eco + Quiet") with AC 240V4 W (AC 100 V) - 5 W (AC 240 V) .11,335 BTU/hour (Lamp Setting 'Bright")/1,165 BTU/hour (Lamp Setting "Eco + Quiet") with AC 100 V1,280 BTU/hour (Lamp Setting 'Bright")/1,130 BTU/hour (Lamp Setting "Eco + Quiet") with AC 240 V41 °F to 95°F (+5°0 to +35°C)-4°F to 140°F (-20'0 to +60°0)Plastic38 kHz

12 W32" x 4 W64" x 11%2" (31 5 (W) x 109 (H) x 280 (D) ram) (main body only)12 W32" x 4 47/64"x 11 37/64"(315 (W) x 120 (H) x 294 (D) mm) (including adjust-ment foot and projecting parts)8.8 Ibs. (4.0 kg)Remote control, Power cord for Europe, except U.K, Power cord for U.K. andSingapore, Power cord for Australia, New Zealand and Oceania, 21 pin RCAconversion adaptor, Video cable, Operation manual

*_ When STANDBY Mode is set to "Eco"

As a part of policy of continuous improvement, SHARP reserves the right to make design and

specification changes for product improvement without prior notice. The performance specifica-tion figures indicated are nominal values of production units. There may be some deviations fromthese values in individual units.

Q -62

Units: inches (mm)

r

o9 7/_ (69.2)

I,, 35/s2(80) • ,3%e(77.5)

12 W32(315)

G

_s_ i _1

I II II I

1 W32(33.8)

2 B%4 1 _s/_ 2 _9/_2

(75) (46.2) (65.5)

(_) -63

iii I

AC socket ....................................................... 28Accessories ................................................... 10Adjustment buttons ........................................ 41Aspect ratio .................................................... 36Auto Power Off ............................................... 49Auto Sync

(Auto Sync adjustment) .............................. 46AUTO SYNC button ....................................... 46

Background .................................................... 48Backlight button ............................................. 13Blue ................................................................ 43Bright ............................................................. 43BrilliantColor TM ............................................... 43

Checking the Input Signal ............................. 46CINEMA ZOOM ...................................... 36, 37Clock .............................................................. 46CLR Temp (Color Temperature) .................... 44C.M.S ............................................................. 44Color .............................................................. 43Contrast ......................................................... 43

DOT BY DOT ................................................. 37DNR ............................................................... 45

ENTER button ................................................ 41Exhaust vent ........................................... 12, 51

Fan Mode ....................................................... 50Fine Sync ....................................................... 46Focus ring ...................................................... 30FREEZE button ............................................. 38

GEOMETRIC ADJUSTMENT ....................... 34

H & V KEYSTONE ......................................... 35HDMI Setting ................................................. 48H-Pos ............................................................. 46HEIGHT ADJUST lever ................................. 30Hue ................................................................ 44

Image Shift .................................................... 47IMAGE SHIFT buttons ................................... 38INPUT 1 terminal ........................................... 23INPUT 1 - 6 modes ....................................... 29INPUT 2 terminal ........................................... 23INPUT 3 terminal ........................................... 24INPUT 4 terminal ........................................... 24INPUT 5 terminal .................................... 25, 26INPUT 6 terminal ........................................... 25INPUT buttons ............................................... 29Intake vent ........................................ 11, 12, 51IRIS button ..................................................... 38

Kensington SecurityStandard connector ............................. 12, 13

KEYSTONE button ........................................ 32Keystone Correction ...................................... 32

Q -64

Lamp ....................................................... 10, 54Lamp indicator ............................................... 52Lamp Setting ................................................. 45Lamp Timer (Life) .......................................... 49Lamp unit ....................................................... 55Language (on-screen display language) ...... 50Lens cap ........................................................ 11

MENU button ................................................ 41

ON button ...................................................... 28

Optional accessories ..................................... 10OSD Display .................................................. 48Overscan ....................................................... 47

Phase ............................................................. 46

Picture Adjustment ........................................ 43Picture Mode .......................................... 38, 43PICTURE MODE button ................................ 38Picture (Screen) Size and Projection Distance....... 20Power cord ..................................................... 28PRJ Mode ............................................... 19, 49Progressive .................................................... 44

R-03 batteries ................................................ 14Rear adjustment foot ..................................... 31Red ................................................................ 43Remote control .............................................. 13Remote control sensor .................................. 15Replacing the lamp ................................. 54, 55Resize ..................................................... 36, 37RESlZE button ............................................... 36RETURN button ............................................. 41RGB/COMR button ........................................ 48

RS-232C Setting ............................................ 50RS-2320 terminal .......................................... 27

Saturation ...................................................... 44Sharp ............................................................. 43SIDE BAR ............................................... 36, 37Special Modes ............................................... 46STANDBY button ........................................... 29STANDBY/ON button .............................. 28, 29STANDBY Mode ............................................ 50STRETCH ............................................... 36, 37Subtitle ........................................................... 47Supplied accessories .................................... 10

Temperature warning indicator ...................... 52Tint ................................................................. 43TRIGGER terminal ........................................ 12

Value .............................................................. 44Video System ................................................ 48V- Pos .............................................................. 46

Zoom ring ....................................................... 30

VALID 1N USA ONLY

CONSUMER LiMiTED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Producf'),when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either

repair the defect or replace the defective Product or part thereof w_tha new or remanufactured equivalent at no charge to the purchaserfor parts or labor for the period(s) set forth below,

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to anyProduct the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal

service or handling, or which has been altered or modified in design or construction,

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof ofpurchase to the servicer,

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIEDWARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED

TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW, Some states do not allow limitations on how long animplied warranty lasts, so the above limitation may not apply to you,

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,or to extend the duration of any warranties beyond the time period described herein Onbehalf of Sharp,

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusiveremedy available to the purchaser, Correction of defects, in the manner and for the period of time described herein, shall constitute

complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute fullsatisfaction of all claims, whether based on contract, negligence, strict liability or otherwise, In no event shall Sharp be liable, or in anyway responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs pertormed by anyoneother than an authorized servicer, Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic orproperty damage, Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not

apply to you,

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE,

Model Specific Section (In-Home Service)

Your Product Model Number & Descriptiom

Warranty Period for this Product:

Additional Item(s_ Excluded fromWarranty Coveraae (if envY:

Where to Obtain Service:

What to do to Obtain Service:

XV-Z30OOU Projector

(Be sure to have this information available when you need servicefor your Product,)

One (1) year parts and labor from date of purchase except for thePlojector Lamp for which the warranty period is ninely (90) daysfrom date of purchase, After the ninety (90) day warranty period onthe Projector Lamp, parts and labor for a lamp replacement are the

responsibility of the consumer,

Cleaning of Optical System and/or replacement of any filter,Labor & materials required to remove and reinstall a suspendedprojector in installations not accessible with a standard (8' step)ladder or ceilings exceeding 12' in height,Labor & materials required to remove and reinstall a projector incomplex systems including, but not limited to, projectors installedin custom enclosures, projectors connected 1o third party control

and automation systems, and realignment of projectors installed in"mirrored" rear projection enclosures,

From a Sharp Authorized Servicer located in the United States,Tofind the location of the nearest Sharp Authorized Servicer, call Sharptoll free at 1-800-BE-SHARR

Contact your Sharp Authorized Servicer to obtain in-home servicefor this Product, The Servicer will come to your home and if

necessary to remove the Product for repair at the Servicer's facility,the Servicer will reinstall it upon completion of repair, Be sure tohave Proof of Purchase available.

TO OBTAIN PRODUCT INFORMATION, CALL 1=800=BE=SHARP (1=800=237=4277) OR VISIT www.sharpusa.com.

i i

ii!i! ill

iii_i i

ii i _ii

(D -65

VALID IN CANADA ONLY

SHARPLiMiTED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!Sharp Electronics of Canada Ltd. (hereinafter called "Sharp") gives the fallowing express warranty to the first consumer purchaser for

this Sharp brand product, when shipped in its original container and sold or distributed inCanada by Sharp or by an Authorized SharpDealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If anysuch defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the

product as specified herein.

This warranty shall not apply to:(a) Any defacts caused or repairs required as a result of abusive operation, negligence, accident, improper installation or ina_roprlate

use as outlined in the owner's manual.

(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp's Authorized ServiceCentres or Sharp's Authorized Servicing Dealers.

(c) Damage caused or repairs required as a result of the use with ifams nat speciffad or approved by Sharp, including but not limitedto head cleaning tapes and chemical cleaning agents.

(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product includng

but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons,cables and pape_

(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and teac(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or

liquid spillage.

(g) Any product received without appropriate model, segal number and CSA/cUL markings.(h) Any products used for rental or commercial purposes.(i) Any installation, setup and/or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp

product together with proof of pulchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centreor an Authorized Sharp Servicing Dealer. In home warlanty service may be provided at Sharp's discretion on any Sharp televisionwith the screen size of 27" or larger and on any Sharp Over The Range Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no athel dealer, service centre or their agent or employee

is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any andall liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resultingfrom a defect in material or workmanship relating to the product including damages for the loss of time or use of this Sharp productor the loss of information. The purchaser will be lesponsible for any removal, reinstallation, transportation and insurance costsincurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations

and responsibilities of Sharp to the purchaser with lespect to the product and shall constitute full satisfaction of all claims, whetherbased on contract, negligence, strict liability or otherwise.

WARRANTY PERIODS

Projector 1 year (bulb 90 days)

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTDI _,O_,TH E--q_,,_,_

SHARP ELECTRONICS OF CANADA LTD.335 Britannia Road East

Mississauga, OntarioL4Z 1W9

(905) 568-7t40

Web site: www.sharp.ca

SHARP

_, SERVICE _

qero_E_,_P'*"

(i_ -66

SHARP XV-Z3000U I! PROJECTOR B PROJETOR IIn · sharp projector projecteur proyector projetor...

Documents

Transcript of SHARP XV-Z3000U I! PROJECTOR B PROJETOR IIn · sharp projector projecteur proyector projetor...