SHARP LC-32D41
-
Upload
kalentoneschat -
Category
Documents
-
view
297 -
download
12
description
Transcript of SHARP LC-32D41
-
LC-32D41ULC-32M41ULC-40C32U
SAFETY PRECAUTIONCHAPTER 1. SPECIFICATIONS
CHAPTER 2. OPERATION MANUAL
CHAPTER 3. DIMENSIONS
CHAPTER 4. REMOVING OF MAJOR PARTS
CHAPTER 5. ADJUSTMENT
CHAPTER 6. TROUBLE SHOOTING TABLE
CHAPTER 7. MAJOR IC INFORMATIONS
CHAPTER 8. OVERALL WIRING/BLOCK DIAGRAM
CHAPTER 9. PRINTED WIRING BOARD ASSEM-BLIES
CHAPTER 10. SCHEMATIC DIAGRAM
Parts Guide
No. S56T6LC32D41U
SERVICE MANUAL
MODELS
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining thesafety and performance of the set.
This document has been published to be used forafter sales service only.The contents are subject to change without notice.
TopPage
In the interests of user-safety (Required by safety regulations in some countries) the set shouldbe restored to its original condition and only parts identical to those specified should be used.
LC-32D41U/LC-32M41U/LC-40C32U
LCD COLOR TELEVISION
-
CONTENTS
SAFETY PRECAUTIONIMPORTANT SERVICE SAFETY PRE-CAUTION.........................................................iPRECAUTIONS A PRENDRE LORS DE LA REPARATION............................................ iiPRECAUTIONS FOR USING LEAD-FREE SOLDER.............................................. iii
CHAPTER 1. SPECIFICATIONS[1] SPECIFICATIONS ...................................... 1-1
CHAPTER 2. OPERATION MANUAL[1] OPERATION MANUAL ............................... 2-1
CHAPTER 3. DIMENSIONS[1] DIMENSIONS ............................................. 3-1
CHAPTER 4. REMOVING OF MAJOR PARTS[1] REMOVING OF MAJOR PARTS ................ 4-1
CHAPTER 5. ADJUSTMENT[1] ADJUSTMENT PROCEDURE.................... 5-1
CHAPTER 6. TROUBLE SHOOTING TABLE[1] TROUBLE SHOOTING TABLE................... 6-1
CHAPTER 7. MAJOR IC INFORMATIONS[1] MAJOR IC INFORMATIONS ...................... 7-1
CHAPTER 8. OVERALL WIRING/BLOCK DIA-GRAM[1] OVERALL WIRING DIAGRAM ................... 8-1[2] SYSTEM BLOCK DIAGRAM ...................... 8-3
CHAPTER 9. PRINTED WIRING BOARD ASSEM-BLIES[1] MAIN Unit.................................................... 9-1[2] IF Unit ....................................................... 9-17[3] R/C, LED Unit ........................................... 9-19[4] KEY Unit ................................................... 9-19
CHAPTER 10. SCHEMATIC DIAGRAM[1] DESCRIPTION OF SCHEMATIC DIA-
GRAM ....................................................... 10-1[2] MAIN Unit.................................................. 10-2[3] IF Unit ..................................................... 10-46[4] R/C, LED Unit ......................................... 10-50[5] KEY Unit ................................................. 10-51
Parts Guide
LC-32D41U/LC-32M41U/LC-40C32U
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &Shock Hazard)Before returning the receiver to the user, perform the followingsafety checks:
3. Inspect all lead dress to make certain that leads are not pinched,and check that hardware is not lodged between the chassis andother metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,insulation materials, cabinet backs, adjustment and compartmentcovers or shields, isolation resistor-capacitor networks, mechanicalinsulators, etc.
5. To be sure that no shock hazard exists, check for leakage current inthe following manner.
Plug the AC cord directly into a 120 volt AC outlet.
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-leled by a 0.15F capacitor in series with all exposed metal cabinetparts and a known earth ground, such as electrical conduit or elec-trical ground connected to an earth ground.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-sitivity or measure the AC voltage drop across the resistor.
Connect the resistor connection to all exposed metal parts having areturn to the chassis (antenna, metal cabinet, screw heads, knobsand control shafts, escutcheon, etc.) and measure the AC voltagedrop across the resistor.
All checks must be repeated with the AC cord plug connectionreversed. (If necessary, a nonpolarized adaptor plug must be usedonly for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) ormore is excessive and indicates a potential shock hazard whichmust be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICEMany electrical and mechanical parts in LCD color television havespecial safety-related characteristics.
These characteristics are often not evident from visual inspection, norcan protection afforded by them be necessarily increased by usingreplacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics areidentified in this manual; electrical components having such featuresare identified by " " and shaded areas in the Replacement Parts Listand Schematic Diagrams.
For continued protection, replacement parts must be identical to thoseused in the original circuit.
The use of a substitute replacement parts which do not have the samesafety characteristics as the factory recommended replacement partsshown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
A V
CAUT ION : FOR CONT INUED
PROTECTION AGAINST A RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
F701 (125V 8A),
F4701, F5701 (250V 3A ~ 115OC)
DVM
AC SCALE
1.5k ohm10W
TO EXPOSEDMETAL PARTS
CONNECT TOKNOWN EARTHGROUND
0.15 F
TEST PROBEi
-
LC-32D41U/LC-32M41U/LC-40C32U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
De nombreuses pices, lectriques et mcaniques, dans les tlvi-
seur ACL prsentent des caractristiques spciales relatives la s-
curit, qui ne sont souvent pas videntes vue. Le degr de protec-
tion ne peut pas tre ncessairement augmente en utilisant des
pices de remplacement talonnes pour haute tension, puissance,
etc.
Les pices de remplacement qui prsentent ces caractristiques sont
identifies dans ce manuel; les pices lectriques qui prsentent ces
particularits sont identifies par la marque " " et hachures dans la
liste des pices de remplacement et les diagrammes schmatiques.
Pour assurer la protection, ces pices doivent tre identiques celles
utilises dans le circuit d'origine. L'utilisation de pices qui n'ont pas
les mmes caractristiques que les pices recommandes par l'usine,
indiques dans ce manuel, peut provoquer des lectrocutions, incen-
dies, radiations X ou autres accidents.
AVERTISSEMENT
1.
2.
3.
4.
5.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
A V
Ne peut effectuer la rparation qu' un technicien spcialis qui s'est parfaitement accoutum toute vrification de scurit et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est danger-
eux.
Dbrancher le rcepteur avant toute rparation.
Inspecter tous les faisceaux de cbles pour s'assurer que les fils
ne soient pas pincs ou qu'un outil ne soit pas plac entre le chs-
sis et les autres pices mtalliques du rcepteur.
Inspecter tous les dispositifs de protection comme les boutons de
commande non-mtalliques, les isolants, le dos du coffret, les cou-
vercles ou blindages de rglage et de compartiment, les rseaux
de rsistancecapacit, les isolateurs mcaniques, etc.
S'assurer qu'il n'y ait pas de danger d'lectrocution en vrifiant la
fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent une prise de cou-
rant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
A l'aide de deux fils pinces, brancher une rsistance de 1.5 k
10 watts en parallle avec un condensateur de 0.15F en srie
avec toutes les pices mtalliques exposes du coffret et une terre
connue comme une conduite lectrique ou une prise de terre
branche la terre.
Utiliser un voltmtre CA d'une sensibilit d'au moins 5000/V pour
mesurer la chute de tension en travers de la rsistance.
Toucher avec la sonde d'essai les pices mtalliques exposes qui
prsentent une voie de retour au chssis (antenne, coffret mtalli-
que, tte des vis, arbres de commande et des boutons, cusson,
etc.) et mesurer la chute de tension CA en-travers de la rsistance.
Toutes les vrifications doivent tre refaites aprs avoir invers la
fiche du cordon d'alimentation. (Si ncessaire, une prise
d'adpatation non polarise peut tre utilise dans le but de termin-
er ces vrifications.)
La tension de pointe mesure ne doit pas dpasser 0.75V (corre-
spondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilit de choc lectrique qui
doit tre supprime avant de rendre le rcepteur au client.
PRECAUTION : POUR LA PRO-
TECTION CONTINUE CONTRE
LES RISQUES D'INCENDIE, RE-
MPLACER LE FUSIBLE
F701 (125V 8A),F4701, F5701 (250V 3A ~ 115OC)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le rcepteur l'utilisateur, effectuer les vrifica-
tions suivantes.
DVM
ECHELLE CA
1.5k ohm10W
0.15 F
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
AVIS POUR LA SECURITE ii
-
LC-32D41U/LC-32M41U/LC-40C32U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder PWBs of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated solderingbit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may bepeeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm thesteady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit asrequired.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
PARTS CODE PRICE RANKPART
DELIVERY DESCRIPTION
ZHNDAi123250E BL J 0.3mm 250g (1roll)ZHNDAi126500E BK J 0.6mm 500g (1roll)ZHNDAi12801KE BM J 1.0mm 1kg (1roll)iii
-
LC-32D41U/LC-32M41U/LC-40C32U
1 1
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
* Emergency alert messages via Cable are unreceivable.As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for productimprovement without prior notice. The performance specification figures indicated are nominal values of production units.There may be some deviations from these values in individual units.
LCD panel
Number of dots
TVFunction
TV-standard
ReceivingChannel
VHF/UHF
CATV
Digital TerrestrialBroadcast (8VSB)
Audio multiplex
Audio out
Terminals Rear INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
ANTENNA
DIGITAL AUDIO OUTPUT
OUTPUT
OSD language
Power Requirement
Power Consumption
Weight
Dimension(W H D)
Operating temperature
3,147,264 dots (1366 768 3 dots)
American TV Standard ATSC/NTSC System
VHF 2-13ch, UHF 14-69ch
1-135ch (non-scrambled channel only)
2-69ch
BTSC System
10W 2
AV in, COMPONENT in
AV in, S-VIDEO in
HDMI in with HDCP
Audio in, HDMI in with HDCP
Audio in, DVI-I in with HDCP
75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
Optical Digital audio output 1 (PCM/Dolby Digital)
Audio out
English/French/Spanish
AC 120 V, 60 Hz
32F to 104F (0C to 40C)
Item LC-32D41U LC-32M41U LC-40C32U
32" Advanced Super View & BLACK TFT LCD
with stand
w/o stand
w/o stand
with stand
164 W
AC 110 240 V, 50/60 Hz
168 W
AC 120 V, 60 Hz
164 W
38.6 lbs./17.5 kg
44.1 lbs./20.0 kg
321/16
2541/64
121/64inch
Digital cable*(64/256 QAM)
1-135ch (non-scrambled channel only)
321/16
2315/64
447/64inch
+ + +
_
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUALPartnames
TV(Front)
TV(R
ear)
Part
names
POWERbutton
Channelbuttons
(CH
/)
Volumebuttons( V
OL
/)
INPUTbutton
OPC
indicator*
POWER
indicator**
OPC
sensor*
Remote
controlsensor
+-
DVIterm
inal
(INPUT5)
INPUT2
term
inals
AUDIO
OUTPUT
term
inals
HDMIterm
inal(INPUT3)
HDMIterm
inal(INPUT4)
Antenna/C
able
in
INPUT1term
inals
DIG
ITALAUDIO
OUTPUT
term
inal
DVIAUDIO
term
inal
(INPUT5)
AUDIO
input
term
inals
(INPUT4)
AC
INPUTterm
inal
2 1
-
LC-32D41U/LC-32M41U/LC-40C32UPartnames
Remote
controlunit
Attachingthestand
QuickReference
32
114
5 64 8
17
15
16
18
19
7
20
109
21
11
23
24
25
12
13
27
22
26
1TVPOWER:SwitchestheTVpoweronorenters
standbymode.
2DISPLAY:Displaysthechannelinform
ation.
3SOURCEPOWER:Turnsthepoweroftheexternal
equipmentonandoff.
4Extern
alequipmentoperationalbuttons:Operates
theexternalequipment.
50_9:Sets
thechannel.
6(D
OT):
7INPUT:Selects
aTVinputsource.(TV,IN
PUT1,IN
PUT
2,IN
PUT3,IN
PUT4,IN
PUT5)
8VOL
/:Sets
thevolume.
9SURROUND:Selects
Surroundsettings.
10
FREEZE:Sets
thestillim
age.Pressagain
toreturn
tonorm
alscreen.
11
EXIT:Turnsoffthemenuscreen.
12
SLEEP:Sets
thesleeptimer.
13
AUDIO
:Selects
theMTS/SAPortheaudio
modeduring
multi-channelaudio
broadcasts.
14
FUNCTIO
N:Switchestheremote
controlforTV,CBL/
SAT,VCR,DVD
andAUDIO
operation.Indicatorlig
hts
up
forthecurrentmode.
*Toenterthecoderegistrationmode,youneedto
press
FUNCTIO
NandDISPLAYatthesametime.
15
LIG
HT
:Whenpressedallbuttonsontheremote
controlunitwilllig
ht.Thelig
htingwillturn
offifno
operationsare
perform
edwithin
about5seconds.This
buttonis
usedforperform
ingoperationsin
low-light
situations.
16
VIEW
MODE:Selects
thescreensize.
17
ENT:Jumpsto
achannelafterselectingwiththe0_9
buttons.
18
FLASHBACK:R
eturnsto
thepreviouschannelor
externalinputmode.
19
CH
/:Selects
thechannel.
20
MUTE:Mutesthesound.
21
MENU:Displaysthemenuscreen.
22
//
//E
NTER:Selects
adesireditem
onthe
screen.
23
RETURN:Returnsto
thepreviousmenuscreen.
24
FAVORITECH
A,B,C,D:Selects
fourpresetfavorite
channels
infour
differentcategories.
While
watching,youcantoggle
theselectedchannels
by
pressingA,B,C
andD.
25
FAVORITE:R
egisters
favorite
channels.
26
CC:Displayscaptionsfrom
aclosed-captionsource.
27
AVMODE:Selects
anaudio
orvideosetting.(W
henthe
inputsourceis
TV,IN
PUT1or2:STANDARD,MOVIE,
GAME,USER,DYNAMIC
(Fixed),DYNAMIC
.Whenthe
inputsourceis
INPUT3,4or5:STANDARD,MOVIE,
GAME,USER,DYNAMIC
(Fixed),DYNAMIC
,PC)
+-
Hexkey
Softcushion
Longscrew
1.
Confirm
the8screwssupplie
dwiththeTV.
NOTE
Todetachthestand,perform
thestepsin
reverseorder.
2.
Attachthetw
opartsofthestandunitto
eachotherusing
the4shortscrewsandthehexkey(supplie
dwiththe
product)asshown.
3.
Insertthestandinto
theopeningonthebottom
ofthe
TV.
Insertandtightenthe4longscrewsinto
the4holeson
therearoftheTV.
Before
attaching(ordetaching)stand,unplugtheAC
cord
from
theAC
INPUTterm
inal.
Before
perform
ingwork
spreadcushioningoverthebaseareato
laytheTVon.
This
willpreventitfrom
beingdamaged.
Short
screws(
4)
(usedin
step2)
Longscrews(
4)
(usedin
step3)
Hexkey
Shortscrew
CAUTIO
N
Attachthestandin
thecorrectdirection.
The"REAR"labelshould
bevisible
from
thebackoftheTV.Referto
thefigure.
Incorrectinstallationofthestandmayresultin
theTVfallingover.
Besure
tofollow
theinstructions.
REAR
Thissidefacestherear.2 2
-
LC-32D41U/LC-32M41U/LC-40C32UBasic
adjustm
entsettings
MenuitemsforTV/INPUT1/INPUT2
MenuitemsforHDMI/DVI
Picture
Setup
Audio
Option
Pow
erCon
trol
DigitalSetup
Picture
Setup
Audio
Option
Pow
erCon
trol
OPC
Backlight
Contrast
Brightness
Color
Tint
Sharp
ness
Advanced
ColorTemp.
Black
3D-Y
/CMonochro
me
Film
Mode
RangeofOPC
EZSetup
CH
Setup
AntennaSetup-D
IGITAL
InputSkip
InputLabel
ParentalCTRL
Position
StandbyMode
Language
Reset
Treble
Bass
Balance
Surround
Audio
Only
DigitalNoiseReduction
InputSelect
OutputSelect
ColorSystem
CaptionSetup
Pro
gram
Title
Display
Favorite
CH
NoSignalOff
NoOperationOff
Audio
Setup
OPC
Backlight
Contrast
Brightness
Color
Tint
Sharp
ness
Advanced
ColorTemp.
Black
Monochro
me
Film
Mode
RangeofOPC
InputSkip
InputSignal
Auto
Sync.
InputLabel
FineSync.
Position
StandbyMode
Language
Reset
Treble
Bass
Balance
Surround
Audio
Only
DigitalNoiseReduction
InputSelect
HDMISetup
OutputSelect
NoSignalOff
NoOperationOff2 3
-
LC-32D41U/LC-32M41U/LC-40C32U
3 1
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 3. DIMENSIONS
[1] DIMENSIONS
121/64 (305)
445/64 (119) 447/64 (120)
15
17/3
2(394.4)
321/16 (814)
279/16 (699.8)
15
3/4(400)
25
41/6
4(651)
23
15/6
4(590)
213/3
2(61)
243/32 (612)
77/8 (200)
361/6
4(100)
77/8(200)
Unit: inch/(mm)
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 4. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS1. Remove the SD Card Cover.
2. Remove the 4 lock screws and detach the Stand Base Ass'y.
3. Remove the 9 lock screws, 3 lock screws and detach the Rear Cabinet.
Stand Base Ass'y
Rear Cabinet
SD Card Cover
3
31
2
4 1
-
LC-32D41U/LC-32M41U/LC-40C32U
4. Remove the 2 lock screws and detach the Stand Assist Angle.
5. Remove the 4 lock screws and detach the Center Angle-L and R.
6. Remove the 3 lock screws and detach the Stand Cover.
7. Remove the 5 lock screws and detach the Stand Fix Angle.
8. Remove the 2 lock screws and detach the Center Assist Angle.
9. Remove the 5 lock screws and detach the MAIN Shield.
Center Angle-LCenter Angle-R
MAIN Shield
Stand Cover
Stand Fix Angle
Stand Assist Angle
Center AssistAngle
6
4
7
5
5
8
9
5
5
4 2
-
LC-32D41U/LC-32M41U/LC-40C32U
10.Disconnect all the connectors from all the PWBs.4 3
-
LC-32D41U/LC-32M41U/LC-40C32U
11.Remove the Speaker-L and R.
12.Remove the 2 lock screws and detach the R/C, LED Unit.
13.Remove the Top Cover Ass'y. Remove the 3 lock screws from the Top Cover Ass'y and detach the KEY Unit.
14.Remove the 4 lock screws and detach the Tray Chassis.
15.Remove the 7 lock screws and detach the Jack Angle Long.
16.Remove the 7 lock screws and detach the POWER Unit.
17.Remove the 4 lock screws and detach the IF Unit.
18.Remove the 2 lock screws, 3 lock screws and detach the MAIN PWB Radiator and MAIN Unit.
Jack Angle Long
Tray Chassis
MAIN Unit
POWER Unit
IF Unit
14
15
15
15
16
18
18
14
1713
12
11 11
MAIN PWB Radiator
Speaker-R
R/C, LED Unit
Speaker-L
Top Cover Ass'y
KEY Unit4 4
-
LC-32D41U/LC-32M41U/LC-40C32U
19.Remove the 14 lock screws and detach the Rug Angles and LCD Panel Module.
1919
19 191919
1919Rug Angle
Rug Angle4 5
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDUREThe adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment isrequired due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following. When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit: DUNTKD640FM22 (LC-32D41U)
MAIN Unit: DUNTKD640FM23 (LC-32M41U)
MAIN Unit: DUNTKD640FM21 (LC-40C32U)
IF Unit: DUNTKD643FM22 (LC-32D41U)
IF Unit: DUNTKD643FM23 (LC-32M41U)
IF Unit: DUNTKD643FM18 (LC-40C32U)
2. Upgrading of each microprocessor software
2.1. Software version upgradeThe model employs the following software.
Main software
Monitor microprocessor software
The main software and the monitor microprocessor software can be upgraded by using a general-purpose SD memory card.
The followings are the procedures for upgrading, explained separately for each of the main software, the monitor microprocessor software.
2.2. Main software version upgrade
SD memory card of 32MB or higher capacity
PC running on Windows 98/98SE/ME/2000/XP operating system
SD memory card reader/writer with USB connectivity.
SD memory card formatting software
(Downloadable at http://panasonic.jp/support/audio/sd/download/sd_formatter_e.html)
To upgrade the main software, it is necessary to get ready the SD card for version upgrade before you start.
Follow the steps below and create the SD card for version upgrade.
1. Insert the SD card into the SD card reader/writer. Start the SD card formatting software. Click [Format]. (When you have the drive options, select the drive where the SD card is inserted before you proceed.)
Caution: Never POWER OFF the unit when software upgrade is ongoing.Otherwise the system may be damaged beyond recovery.
Get ready before you start
Preparations5 1
-
LC-32D41U/LC-32M41U/LC-40C32U
2. When the formatting is over, the following window appears. Click [OK].
3. Click [Exit] to finish the formatting.
NOTE: When you are done, take out the SD card once to make sure it is finished, and then insert it again.
4. Copy the binary image file D41(D41U, M41U, 40C32)UAxxx.SDC (named temporarily) for version upgrade to the root directory (folder) of the SDcard drive.
NOTE: In the SD card drive, do not store other folders or unrelated files, or more than one binary image files for version upgrade.
Now the SD card for version upgrade is ready.
5. Shut off the AC power (i.e. unplug the AC cord).
6. Insert the SD card for version upgrade (prepared as above) into the service socket located lower side from center at terminals, above S-VIDEOterminal in the rear of the unit, in a way that the cut corner of the SD card comes at the upper side.
NOTE: If the SD card is inserted in a wrong way, the card will go deep inside the unit beyond retrieval. Take due care to insert the SD card correctly.
7. Turn on the AC power (i.e. plug in the AC cord).
8. After the unit startup, the system upgrade screen as shown below appears within 20-40 seconds.
How to upgrade the software
SYSTEM UPGRADE
Program
EEPROM
12%
Part Init
U0601051OLD Version
NEW Version U0601241
M1505 2
-
LC-32D41U/LC-32M41U/LC-40C32U
9. Even a single failure in the process will trigger the upgrade failure screen as shown below. The word NG changes to red for the item failed.
NOTE: In the event of a failure, repeat the upgrading process. If the process repeatedly fails, it is likely that the hardware is troubled.
10.Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on thisscreen. The version information appears after the upgrade is complete.
11.Shut off the AC power to the unit (unplug the AC cord), and remove the SD card for version upgrade.
12.Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mainsoftware version information.
UPGRADE FAILURE
Program
EEPROM
NG
NG
24%
Part Init
U0601051OLD Version
NEW Version U0601241
UPGRADE SUCCESS
Program
EEPROM
NG
NG
100%
Part Init
U0601241Main Version5 3
-
LC-32D41U/LC-32M41U/LC-40C32U
2.3. Monitor microprocessor software version upgradeNOTE: If Monitor version in the process menu is 2.00M, the monitor microprocessor software can not be rewritten (because IC2002 has been
replaced with the mask type).
Get ready the same items as listed in the Main software version upgrade.
Create the SD card for monitor microprocessor software version upgrade in the same manner as explained in the Main software version upgrade.Copy the binary image file M150Mxxx.SDC (named temporarily) for monitor microprocessor software version upgrade to the SD card drive.
1. Shut off the AC power to the unit (i.e. unplug the AC cord).
2. Insert the SD card for version upgrade (prepared as above) into the service socket located lower side from center at terminals, above S-VIDEOterminal in the rear of the unit, in a way that the cut corner of the SD card comes at the upper side.
NOTE: If the SD card is inserted in a wrong way, the card will go deep inside the unit beyond retrieval. Take due care to insert the SD card correctly.
3. Turn on the AC power (i.e. plug in the AC cord).
CAUTION: The moment this operation is done, the upgrading of the monitor microprocessor software starts. While the upgrade is ongoing,never power off the unit. Otherwise the upgrade will fail and the system may have a serious damage beyond recovery (inabilityto start).
4. After the unit startup, the system upgrade screen as shown below appears within 10-30 seconds.
5. A failure in the process will trigger the upgrade failure screen. The word NG changes to red for the item failed.
NOTE: In the event of a failure, repeat the upgrading process. If the process repeatedly fails, it is likely that the hardware is troubled.
6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on thisscreen. The version information appears after the upgrade is complete.
7. Shut off the AC power to the unit (unplug the AC cord), and remove the SD card for version upgrade.
8. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-itor microprocessor software version information.
2.4. Video signal adjustment procedure1) Image adjustment
1. Device check
Before adjustment, make sure that the adjusting device and signal source are set for the Sharp LCD US.
Signal generator level adjustment check (Adjustment to the specified level)
Get ready before you begin
Preparation
How to upgrade the software
Composite signal : 0.714Vp-p 0.02Vp-p (Pedestal to white level) 15K component signal : Y level : 0.714Vp-p 0.02Vp-p (Pedestal to white level)
PB, PR level : 0.7Vp-p 0.02Vp-p 33K component signal : Y level : 0.7Vp-p 0.02Vp-p (Pedestal to white level)
PB, PR level : 0.7Vp-p 0.02Vp-p DVI-I (Analog RGB) signal : RGB level : 0.7Vp-p 0.02Vp-p (Pedestal to white level)
MONITOR UPGRADE
Program
NG12%
1.00OLD Version
NEW Version 1.02
M1505 4
-
LC-32D41U/LC-32M41U/LC-40C32U
2. Entering the adjustment process mode
3. N358 composite signal / Tuner adjustment
4. Component 15K signal adjustment
5. Component 33K signal adjustment
Adjustment item Adjustment conditions Adjustment procedure1 Adjustment pro-
cess modeEnter the process adjustment mode using the process adjustment remote control.
Adjustment item Adjustment conditions Adjustment procedure1 Adjustment N358 signal
US-10chFeed the N358 color bar signal (75% color saturation) to VIDEO 1 input.Feed the RF signal (by use of US-10ch) to TUNER.
2 Auto adjustment performance
Page 3 Bring the cursor on [ N358 ALL ADJ] and press [ENTER].[ N358 ALL ADJ FINISH] appears when finished.
Adjustment item Adjustment conditions Adjustment procedure1 Adjustment 480i signal Feed the 100% color bar signal to VIDEO 1 component input.
2 Auto adjustment performance
Page 5 Bring the cursor on [ COMP 15K MAIN ADJ] and press [ENTER].[ COMP 15K MAIN ADJ FINISH] appears when finished.
Adjustment item Adjustment conditions Adjustment procedure1 Adjustment 1080i signal Feed the 100% color bar signal to VIDEO 1 component input.
2 Auto adjustment performance
Page 6 Bring the cursor on [ HDTV ADJ] and press [ENTER].[ HDTV ADJ FINISH] appears when finished.
[Video input signal] [US-10CH]
100% white 100% white
75% color saturation
0% black
480i
100% color bar signal
100% white
0% black
1080i
100% color bar signal
100% white5 5
-
LC-32D41U/LC-32M41U/LC-40C32U
6. DVI-I (analog) signal adjustment
2.5. Adjustment of white balance1. White balance adjustment
Adjustment item Adjustment conditions Adjustment procedure1 Adjustment DVI-I (analog)
signal: XGA (1024 x 768) 60HzSYNC:HV separate
Feed the XGA (100%) white 1/2 window to DVI-I (analog).
2 Auto adjustment performance
Bring the cursor on [ DVI ANALOG ADJ] and press [ENTER].[ DVI ANALOG ADJ OK] appears when finished.
Adjustment item Adjustment conditions Adjustment procedure1 Setting 1) Apply the following settings to the set.
AV MODE: [DYNAMIC] Backlight: +16 Aging Time: Min. 60 minutes
2) Connect a white balance adjustment jig and the set.2 Execution of auto
adjustment[Command]Process modeKRSW0001KKT10037
SettingKYOF0000OSDS0001SBSL0016
Multipoint adjustment modeMSET0001
Adjustment value initializa-tionMSET0004
Point 6LEV60944MG6G****MG6B****MG6R****
Point 5LEV50800MG5G****MG5B****MG5R****
[Adjustment method]1) Send the monitor adjustment process code with the R/C.2) Set the point 6 to the specified gradation. Set the strongest color as the fixed color
and adjust RGB to the standard value by minus adjustment.3) Set the point 5 to the specified gradation. Set the correction value of G [(Initial value
of point 5) x (G value of point 6) / (Initial value of point 6)] and adjust RB to the stan-dard value.
4) Set the point 4 to the specified gradation. Set the correction value of G [(Initial value of point 4) x (G value of point 6) / (Initial value of point 6)] and adjust RB to the stan-dard value.
5) Set the point 3 to the specified gradation. Set the correction value of G [(Initial value of point 3) x (G value of point 6) / (Initial value of point 6)] and adjust RB to the stan-dard value.
6) Set the point 2 to the specified gradation. Set the correction value of G [(Initial value of point 2) x (G value of point 6) / (Initial value of point 6)] and adjust RB to the stan-dard value.
7) Set the point 1 to the specified gradation. Set the correction value of G [(Initial value of point 1) x (G value of point 6) / (Initial value of point 6)] and adjust RB to the stan-dard value.
8) Write the adjustment values with the MSET0003 command and turn off AC power.
* Initial value of each point: Set gradation level x 4
[Adjustment values]Conform to Standard set submitted by Engineering Department.[LC-32D50U] Teaching set[Adjustment standard values] Measuring device: [Minolta CA-210] technical measuring device
Point 4 Level Standard value Adjustment spec Test specLEV40576 Point 6 944 X=0.272 0.0012 0.0020MG4G**** y=0.277MG4B**** Point 5 800 X=0.272 0.0012 0.0020MG4R**** y=0.277
Point 4 576 X=0.272 0.0012 0.0020Point 3 y=0.277LEV30464 Point 3 464 X=0.272 0.0012 0.0020MG3G**** y=0.277MG3B**** Point 2 264 X=0.272 0.0012 0.0020MG3R**** y=0.277
100% White
0% Black
1/4
1/4
1/2
1/4 1/41/25 6
-
LC-32D41U/LC-32M41U/LC-40C32U2.6. Key writing1. EDID writing (Main PWB: DUNTKD640FM21/22/23 DVI input terminal/HDMI input terminal)
Point 2 Point 1 200 X=0.272 0.0020 0.0035LEV20264 y=0.277MG2G****MG2B****MG2R****
Note2
Test conditions of the set:AV MODE: [DYNAMIC] (Reset)Monochrome: ONAging Time: Min. 60 minutes
Point 1LEV10200MG1G****MG1B****MG1R****
WritingMSET0003
Adjustment item Adjustment conditions Adjustment procedure1 DVI EDID writing File version check 1) Write the EDID data for DVI into IC1505 mounted on the
main PWB with the checker.TL1514 I2C clock, TL1515 I2C dataTL1516 5V, TL1517 GNDTL1536 write protection (H: WP, Low: write enable)
2 HDMI EDID writ-ing
Inspection modeFile version check
1) Write the EDID data for HDMI into IC1501/IC1502 mounted on the main PWB with the checker.TL1508/1510 I2C clock, TL1509/1511 I2C dataTL1512/1513 5V, TL1519/1518 GNDTL1534/1535 write protection (H: WP, Low: write enable)
2) Perform data writing before the checker inspects HDMI.(If no data has been written, HDMI does not function.)
Adjustment item Adjustment conditions Adjustment procedure5 7
-
LC-32D41U/LC-32M41U/LC-40C32U
2. Adjustment sequence (adjustment according to the G adjustment value of gradation 6)
* Make sure the adjusting point gradations are correct since they are different for each model.
PC Set
Set the light level to MAX with the light control command
(SBSL0016 for 45).
SBSL0016
Setting is complete.
OK
Multi point adjustment mode setting
MSET0001
Multi point adjustment mode is set.
OK
Initialize adjustment values.
MSET0004
Initialization is done.
OK
Adjustment gradation setting (point 6 = 236 gradation adjustment*)
LEV60944
Adjust RGB to the target xy values.
MG6RXXXX
MG6GXXXX
MG6BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* In order to adjust by reducing the value, set the strongest color
as the fixed color.
* The default adjustment value of RGB is the parameter value of
the LEV6 command multiplied by 2.
Adjustment values are set.
OK
Adjustment gradation setting (point 5 = 200 gradation adjustment*)
LEV50800
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
Pattern display
Adjustment values are set.
OK
Correction of G value
MG5GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
LEV5) x 2 x (the ratio).
Adjustment values are set.
OK
Pattern display
The adjustment value is
reflected in the image.5 8
-
LC-32D41U/LC-32M41U/LC-40C32UPC Set
Adjust RB to the target xy values.
MG5RXXXX
MG5BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
* The default adjustment value of RGB is the parameter value
of the LEV5 command multiplied by 2.
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
The adjustment value is
reflected in the image.
Start measurement
Adjustment gradation setting (point 4 = 144 gradation adjustment*)
LEV40576
Adjustment values are set.
OK
Correction of G value
MG4GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
LEV4) x 2 x (the ratio).
Adjustment values are set.
OK
Pattern display
Adjust RB to the target xy values.
MG4RXXXX
MG4BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
* The default adjustment value of RGB is the parameter value of
the LEV4 command multiplied by 2.
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
The adjustment value is
reflected in the image.
Adjustment gradation setting (point 3 = 116 gradation adjustment*)
LEV30464
Adjustment values are set.
OK
Correction of G value
MG3GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
LEV3) x 2 x (the ratio).
Adjustment values are set.
OK
Pattern display
Start measurement5 9
-
LC-32D41U/LC-32M41U/LC-40C32UPC Set
Adjust RB to the target xy values.
MG3RXXXX
MG3BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
* The default adjustment value of RGB is the parameter value of
the LEV3 command multiplied by 2.
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
The adjustment value is
reflected in the image.
Adjustment gradation setting (point 2 = 66 gradation adjustment*)
LEV20264
Adjustment values are set.
OK
Correction of G value
MG2GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
LEV2) x 2 x (the ratio).
Adjustment values are set.
OK
Pattern display
Start measurement
Adjust RB to the target xy values.
MG2RXXXX
MG2BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
* The default adjustment value of RGB is the parameter value of
the LEV2 command multiplied by 2.
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
The adjustment value is
reflected in the image.
Adjustment gradation setting (point 1 = 50 gradation adjustment*)
LEV10200
Adjustment values are set.
OK
Correction of G value
MG1GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
LEV1) x 2 x (the ratio).
Adjustment values are set.
OK
Pattern display
Start measurement5 10
-
LC-32D41U/LC-32M41U/LC-40C32U2.7. Initialization to factory settingsAfter the shipping setting, pull off the AC cord.
NOTE: Never turn on the power after the shipping setting. If power is turned on, perform the shipping setting again.
Adjustment item Adjustment conditions Adjustment procedure1 Initialization It turns off with AC power supply. Place the cursor on the [INDUSTRY INIT] row, set ON with
[+] or [-] of the [VOL] key, and press the [ENT] key.Version confirmation screen appears.[SUCCESS] on a green line indicates that the setting is suc-cessfully completed.(In case of an error, [ERROR] and an error code appear on a red line.)Turn off the AC power.1. User setting2. Channel data (e.g. broadcast frequencies)3. Password data4. Operation time5. Auto installation flag6. V-CHIP block setting
PC Set
Adjust RB to the target xy values.
MG1RXXXX
MG1BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
* The default adjustment value of RGB is the parameter value of
the LEV1 command multiplied by 2.
Adjustment values are set.
OK
Repeat until RGB
become the target
values.
The adjustment value is
reflected in the image.
Writing of adjusted values
MSET0003
Deletion is complete.
OK
Deleting adjustment patterns
MSET0000
Writing is complete.
OK
Start measurement
Completion of adjustment5 11
-
LC-32D41U/LC-32M41U/LC-40C32U
2.8. Menu list in process A mode
Page Line Item1 MAIN Version Main microcomputer software version
BOOT VersionMonitor Version Monitor microcomputer software versionEQ DATA CHECKSUM Sound parameter checksumTEMPERATURE Read value of temperature sensorLAMP ERROR Number of lamp errorNORMAL STANDBY CAUSE Reasons of standby at normal timeERROR STANDBY CAUSE Reasons of standby in the event of error
2 INDUSTRY INIT (+Cause) Initialization to factory settings (including clearing Standby Cause data)INDUSTRY INIT Initialization to factory settingsHOTELMODE Activate/deactivate the hotel modeCenter Acutime Main microcomputer operating timeRESET Reset main microcomputer operating time
Lamp error restBacklightAcutime Backlight lighting timeRESET Reset backlight lighting timeLAMP ERROR RESETVIC XPOS x-coordinate for reading image dataVIC YPOS y-coordinate for reading image dataVIC COLOR Specification of color for reading image dataVIC SIGNAL TYPE Specification of signal for reading image dataVIC READ On/Off of image data read operation
3 N358 ALL ADJ Auto adjustment of NTSC and TUNER signalsN358 MAIN ADJ Auto adjustment of NTSC signalTUNER DAC ADJ Auto adjustment of TUNERN358 MAIN CONTRAST NTSC contrast adjustmentTUNER A DAC TUNER DAC adjustment
4 TUNER VCHIP TEST(69ch) Execute TUNER TESTTUNER VCHIP TEST(7ch)TUNER VCHIP TEST(10ch)TUNER VCHIP TEST(15ch)
5 COMP15K MAIN ADJ Auto adjustment of component 15kCOMP15K MAIN CONTRAST Component 15k contrast adjustment
6 HDTV ADJ HDTV auto adjustmentCONTRAST HDTV contrast adjustmentCb GAIN HDTV CB gain adjustmentCr GAIN HDTV CR gain adjustmentHDTV Y OFFSET HDTV Y offset adjustmentHDTV Cb OFFSET HDTV CB offset adjustmentHDTV Cr OFFSET HDTV CR offset adjustment
7 DVI ANALOG DVI ANALOG adjustmentR CUTOFF R CUTOFF adjustment valueG CUTOFF G CUTOFF adjustment valueB CUTOFF B CUTOFF adjustment valueR DRIVE R DRIVE adjustment valueG DRIVE G DRIVE adjustment valueB DRIVE B DRIVE adjustment value
8 MONITOR GAMMA IN 1 White balance adjustment IN-Point1MONITOR GAMMA IN 2 White balance adjustment IN-Point2MONITOR GAMMA IN 3 White balance adjustment IN-Point3MONITOR GAMMA IN 4 White balance adjustment IN-Point4MONITOR GAMMA IN 5 White balance adjustment IN-Point5MONITOR GAMMA IN 6 White balance adjustment IN-Point6GAMMA WRITE Write adjustment valuesGAMMA RESET Reset adjustment values5 12
-
LC-32D41U/LC-32M41U/LC-40C32U9 MONITOR GAMMA R 1 White balance adjustment OUT R-Point1MONITOR GAMMA G 1 White balance adjustment OUT G-Point1MONITOR GAMMA B 1 White balance adjustment OUT B-Point1MONITOR GAMMA R 2 White balance adjustment OUT R-Point2MONITOR GAMMA G 2 White balance adjustment OUT G-Point2MONITOR GAMMA B 2 White balance adjustment OUT B-Point2MONITOR GAMMA R 3 White balance adjustment OUT R-Point3MONITOR GAMMA G 3 White balance adjustment OUT G-Point3MONITOR GAMMA B 3 White balance adjustment OUT B-Point3GAMMA WRITE Write adjustment valuesGAMMA RESET Reset adjustment values
10 MONITOR GAMMA R 4 White balance adjustment OUT R-Point4MONITOR GAMMA G 4 White balance adjustment OUT G-Point4MONITOR GAMMA B 4 White balance adjustment OUT B-Point4MONITOR GAMMA R 5 White balance adjustment OUT R-Point5MONITOR GAMMA G 5 White balance adjustment OUT G-Point5MONITOR GAMMA B 5 White balance adjustment OUT B-Point5MONITOR GAMMA R 6 White balance adjustment OUT R-Point6MONITOR GAMMA G 6 White balance adjustment OUT G-Point6MONITOR GAMMA B 6 White balance adjustment OUT B-Point6GAMMA WRITE Write adjustment valuesGAMMA RESET Reset adjustment values
11 AUDIO SELECT Select sound parameter data (ROM/EEP)INPUT_TRIM_SPINPUT_TRIM_HPCLIPPER_LEVELANGLEMASTER_VOLUMESCART_PRESCALEFM_AM_PRESCALEI2S1_PRESCALESCART1_VOLUMESCART2_VOLUME
12 AIN1_ADC_VOLUMEAIN2_ADC_VOLUMEAIN3_ADC_VOLUMEAIN4_ADC_VOLUMEAIN5_ADC_VOLUMEAIN6_ADC_VOLUME
13 SUB_VOLUME_SURROUNDSUB_VOLUME_FLATSUB_VOLUME_EQSUB_VOLUME_HPSUB_VOLUME_HP_CENTERSPSUB_VOLUME_CENTERSP_EQSUB_VOLUME_CENTERSP_FLATBBE_HF_ADJUSTBBE_LEVELBBE_MACH3_F0BBE_MACH3_QBBE_MACH3_GAIN
14 EQ_MODEPEQ1_F0PEQ1_QPEQ1_GAINPEQ2_F0PEQ2_Q
Page Line Item5 13
-
LC-32D41U/LC-32M41U/LC-40C32U14 PEQ2_GAINPEQ3_F0PEQ3_QPEQ3_GAINPEQ4_F0PEQ4_QPEQ4_GAIN
15 PEQ5_F0PEQ5_QPEQ5_GAINEALA_GAIN
16 BRIGHTNESS DA0BRIGHTNESS DA1BRIGHTNESS DA2BRIGHTNESS DA3BRIGHTNESS DA4BRIGHTNESS DA5BRIGHTNESS DA6BRIGHTNESS DA7BRIGHTNESS DA8BRIGHTNESS DA9BRIGHTNESS DA10BRIGHTNESS DA11
17 BRIGHTNESS DA12BRIGHTNESS DA13BRIGHTNESS DA14BRIGHTNESS DA15BRIGHTNESS DA16BRIGHTNESS DA17BRIGHTNESS DA18BRIGHTNESS DA19BRIGHTNESS DA20BRIGHTNESS DA21BRIGHTNESS DA22
18 BRIGHTNESS DA23BRIGHTNESS DA24BRIGHTNESS DA25BRIGHTNESS DA26BRIGHTNESS DA27BRIGHTNESS DA28BRIGHTNESS DA29BRIGHTNESS DA30BRIGHTNESS DA31BRIGHTNESS DA32
19 OPC33 ADLEVEL 0OPC33 ADLEVEL 1OPC33 ADLEVEL 2OPC33 ADLEVEL 3OPC33 ADLEVEL 4OPC33 ADLEVEL 5OPC33 ADLEVEL 6OPC33 ADLEVEL 7OPC33 ADLEVEL 8OPC33 ADLEVEL 9OPC33 ADLEVEL 10OPC33 ADLEVEL 11
20 OPC33 ADLEVEL 12OPC33 ADLEVEL 13
Page Line Item5 14
-
LC-32D41U/LC-32M41U/LC-40C32U2.9. Code list for Standby Cause
20 OPC33 ADLEVEL 14OPC33 ADLEVEL 15OPC33 ADLEVEL 16OPC33 ADLEVEL 17OPC33 ADLEVEL 18OPC33 ADLEVEL 19OPC33 ADLEVEL 20OPC33 ADLEVEL 21OPC33 ADLEVEL 22
21 OPC33 ADLEVEL 23OPC33 ADLEVEL 24OPC33 ADLEVEL 25OPC33 ADLEVEL 26OPC33 ADLEVEL 27OPC33 ADLEVEL 28OPC33 ADLEVEL 29OPC33 ADLEVEL 30OPC33 ADLEVEL 31
22 V6 OS THERMO 1V6 OS THERMO 2V6 OS THERMO 3V6 OS THERMO 4V6 OS THERMO 5V6 OS THERMO 6V6 OS THERMO 7
23 V5 OS THERMO 1V5 OS THERMO 2V5 OS THERMO 3V5 OS THERMO 4V5 OS THERMO 5V5 OS THERMO 6V5 OS THERMO 7
24 MONITOR TIME OUTMONITOR MAX TEMPMONITOR STANDBY CAUSE
25 LCD TEST PATTERN
26 KEY LOCK(1217)KOUTEI AREA ALL CLEARA MODE AREA CLEARBACKUP AREA CLEARB MODE AREA CLEAREXECUTION
27 EEP SAVEEEP RECOVERSTANDBY CAUSE RESET
Code Indication Description1 RC_STNBY /* Standby set by remote control */2 E_CCKMVT /* Abnormal voltage of CCKM line detected */5 OUT_OF_R /* While a PC display is on, unspecified input continued long time. */6 NO_OPERT /* Off caused by no operation */7 NO_SIGNA /* Off caused by no signal */8 PC_MODE1 /* Set by the PC power management mode 1 */9 PC_MODE2 /* Set by the PC power management mode 2 */A SLEEP_TM /* Set by off timer */B E_NOMONI /* Incompatible monitor is connected to the AVC center. */
Page Line Item5 15
-
LC-32D41U/LC-32M41U/LC-40C32UC OFF_232C /* Set by the command from RS232C */E AVC_TACT /* Set by the front switch at the AVC center */F BSBOOKED /* The pre-set time has passed since TV was turned on from standby by the BS timer. */10 E_AVCFAN /* Fan failure at the AVC center */11 E_BSSUBM /* Communication failure with the BS sub microcomputer (Not used) */12 E_CVICIC /* CVIC failure */13 E_AVCTMP /* Abnormal temperature at the AVC center */14 E_1BITAU /* 1Bit-AMP failure */15 E_MONIPW /* Monitor main power failure detected */16 E_MONITR /* Monitor problem detected */17 E_FNLOCK /* Fan lock for North America */40 /* Failure in Digital Standby */
Code Indication Description5 16
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 6. TROUBLE SHOOTING TABLE
[1] TROUBLE SHOOTING TABLE
No power supply (Front LED does not light up) and no power-up even is turned on (Front LED light up to blue)
Is the AC cord connected? NO Connect the AC cord and turn on the power.
YESAre the harness and FFC connected prop-erly?
NO Connect the harness and FFC properly.
YESAre F701 normal? NO If the fuse is blown when turning on the power after replacing F701, replace VZ701,
DS4701, F4701/F4702, F5701, Q4701/Q4702, Q5701, IC4701 and IC5701, then recheck.
YESIs the voltage of C4701/C4702/C4703 approx. 160V?
NO Check if VZ701, R701, R702, R703 and DS4701 are normal.
YESIs BU5V supplied? NO
Do the primary side and secondary side of T5701 oscillate normally?
YES
YES NOAre F5702, D5705, IC5706 and D5717 out of order?
Are there defective parts on the pri-mary side? Is the output on the sec-ondary side short-circuited?
Are UR6V/UR10V/UR13V supplied? NO Does PS_ON (pin 1 of CN5702) become High (approx. 3.3V)?
YES
YES NOCheck the regulator circuit of UR6V, rectifier circuit of UR13V and DC/DC circuit of UR10V.
Is the unit set to STANDBY MODE2? Is the main unit normal?
Is 24V supplied? NO Do the primary side and secondary side of T4701 oscillate normally?
YES
YES NOAre D4705/D4706 out of order? Are there defective parts on the pri-
mary side? Is the output on the sec-ondary side short-circuited?
Is PNL5V supplied? NO Does PNL_POW (pin 4 of CN5702) become High (approx. 3.3V)?
YES Check the DC/DC circuit of PNL5V? Is the main unit normal?
Turn on the power again, and check if the unit works normally.
Remarks
State of the setPS_ON
(CN5702 )PNL_POW
(CN5702 )BU5V
(CN5702 )UR6V
(CN5701 )UR10V
(CN5701 )UR13V
(CN5701 )PNL5V
(CN5701 )24V
(CN5703 )
STDBYMODE1 High High 5V 6V 10V 13V 5V 24VMODE2 Low Low 5V - - - - -
Power ON High High 5V 6V 10V 13V 5V 24V
1 4 5 1 7 11 3 16 1
-
LC-32D41U/LC-32M41U/LC-40C32UNo audio output during UHF/VHF reception
Is SIF output from the tuner (TU1101_Pin3) normal? NO Check the tuner and peripheral circuits.
YESIs input signal fed to pin 21 (SOUNDIF 1) of IC1401 (SIF Demod-ulator) normal?
NO Check the filter circuits (Q1144 and Q1102-3) and peripheral cir-cuits.
YESAre audio signals from pins 29 and 30 (SC2_OUTL/R) of IC1401 to pins 51 and 52 of IC1403 (CODEC) normal?
NO Check between pins 29 and 30 (SC2_OUTL/R) of IC1401 and pins 51 and 52 of IC1403 (CODEC).
YESAre audio outputs (A-OUT_L/R) of pins 38 and 39 of IC1403 nor-mal?
NO Are the LRCK, BICK, SDTO and SDTI signals sent from IC1403 to IC1406 (DSP) normally?
YES
YESCheck IC1403 and peripheral circuits.
Is audio input from pins 38 and 39 of IC1403 to pins 11 and 15 of IC2701(STEREO_AMP) normal?
NO Check the circuits between pins 38 and 39 of IC1403 and pins 11 and 15 of IC2701. (MUTE circuits: Q1306-8)
YESIs audio output from IC2701 normal? NO Check IC2701 and peripheral circuits.
YESIs the speaker switching circuit (T2701)
YESCheck the connector (P2703) of AV_UNIT and around the speak-ers.
No monitor audio output
Is monitor audio output set to Variable? YES Reset monitor audio output to Fixed.
NOAre audio output pins 40 and 41 of IC1403 (CODEC) normal? NO Check IC1403 and peripheral circuits.
YESAre audio output pins 7 and 1 of IC1407 (Buffer_AMP) normal? NO Check IC1407 and peripheral circuits.
YESCheck between IC1407 and MONITOR OUTPUT terminal (pins 10 and 16 of J502).6 2
-
LC-32D41U/LC-32M41U/LC-40C32UNo audio output from external input
Is L-ch audio signal fed from pin 12 of input terminal J501 to pin 53 of IC1403?Is R-ch audio signal fed from pin 18 of input terminal J501 to pin 54 of IC1403?
Is L-ch audio signal fed from pin 10 of input terminal J501 to pin 57 of IC1403?Is R-ch audio signal fed from pin 16 of input terminal J501 to pin 58 of IC1403? [INPUT-3/INPUT4 (Digital audio mode)]Is digital audio signal (HDMI_SPDIF) fed from pin 70 of IC1508 to pin 2 of IC1401? [INPUT-4 (Analog audio mode)]Is L-ch audio signal fed from pin 3 of input terminal J1501 to pin 59 of IC1403?Is R-ch audio signal fed from pin 2 of input terminal J1501 to pin 60 of IC1403?
Is L-ch audio signal fed from pin 2 of input terminal J1502 to pin 55 of IC1403?Is R-ch audio signal fed from pin3 of input terminal J1502 to pin 56 of IC1403?
YES
No audio output during digital broadcasting reception
Are the I2S signals MCLK, SCLK, LRCK, and DATA sent from pins N22, N19, N21 and M20 of IC8101 (PH1) nor-mally?
NO Check around IC8101 PH1.
YESAre input signals of pins 24 (MCLK), 11 (SCLK), 10 (LRCK), 32 (DATA) of IC1403 normal?
NO Check the circuits between pins N22, N19, N21 and M20 of IC8101 PH1 and pins 24, 11, 10 and 32 of IC1403.
YESAre audio signals from pins 29 and 30 (SC2_OUTL/R) of IC1401 to pins 51 and 52 of IC1403 (CODEC) normal?
NO Check between pins 29 and 30 (SC2_OUTL/R) of IC1401 and pins 51 and 52 of IC1403 (CODEC).
YESAre audio outputs (A-OUT_L/R) of pins 38 and 39 of IC1403 nor-mal?
NO Are the LRCK, BICK, SDTO and SDTI signals sent from IC1403 to IC1406 (DSP) normally?
YES
YESCheck IC1403 and peripheral circuits.
Is audio input from pins 38 and 39 of IC1403 to pins 11 and 15 of IC2701(STEREO_AMP) normal?
NO Check the circuits between pins 38 and 39 of IC1403 and pins 11 and 15 of IC2701. (MUTE circuits: Q1306-8)
YESIs audio output from IC2701 normal? NO Check IC2701 and peripheral circuits.
YESIs the speaker switching circuit (T2701)
YESCheck the connector (P2703) of AV_UNIT and around the speak-ers.6 3
-
LC-32D41U/LC-32M41U/LC-40C32U No video output (1)
No video output from external input Select INPUT-1 and the input signal on the input switching menu
screen. Is INPUT-1 selected on the input switching menu screen? NO When INPUT-1 cannot be selected since the characters INPUT-1
on the menu screen are gray.
YES
Is the video signal detection function normal?Check between pin 5 of J501 and pin 70 of IC501.
Is video signal fed to pin 65 of IC501 (AV SWITCH)? NO Check between pin 4 of J501 and pin 65 of IC501.
YESIs video signal sent to pin 60 of IC501? NO Check IC501 (AV SWITCH) and peripheral circuits.
YESIs video signal sent to pin 2 of IF_UNIT connector (FC_SC501)? NO Check between IC501 and SC501. (Q501, Q502, etc.)
YESIs video signal fed to pin 2 of MAIN_UNIT connector (FC_SC1101)?
NO Check the board-to-board cable FC.
YESIs video signal fed to pin 242 of IC3301 (Trident) via L.P.F. com-posed of Q2201 and Q2207?
NO Check between IC501 and IC3301. (Q2201, Q2207, etc.)
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301?
NO Check IC3301 and peripheral circuits.
YESCheck LCD_CONTROL PWB.6 4
-
LC-32D41U/LC-32M41U/LC-40C32U No video output (2)
No video output from external input Select INPUT-2 and the input signal on the input switching menu
screen. Is INPUT-2 selected on the input switching menu screen? NO When INPUT-2 cannot be selected since the characters INPUT-3
on the menu
YES
Is the video signal detection function normal? Check between pin 2 of J501and pin 2 of IC501.Is the S-video signal detection function normal? Check between pin 6 of J503 and pin 6 of IC501.
Is signal fed to each input terminal of IC501 (AV SWITCH)?
Is video signal fed to pin 3 of IC501?
NO Check between pin 1 of J501 and pin 3 of IC501.
Are Y and C signals fed to pins 5 and 7 of IC501 respectively?
NO Check between pins 3 and 4 of J503 and pins 5 and 7 of IC501.
YES
Is video signal sent to pin 60 of IC501?
Are Y and C signals sent to pins 60 and 59 of IC501 respec-tively?
NO Check IC501 (AV SWITCH) and peripheral circuits.
YES
Is video signal sent to pin 2 of IF_UNIT connector (FC_SC501)?
Are Y and C signals sent to pins 2 and 4 of IF_UNIT connector (FC_SC501) respectively?
NO Check between IC501 and SC501. (Q501, Q502, Q503, Q504, etc.)
YES
Is video signal fed to pin 2 of MAIN_UNIT connector (FC_SC1101)?
Are Y and C signals fed to pins 2 and 4 of MAIN_UNIT connector (FD_SC1101) respectively?
NO Check the board-to-board cable FC.
YES
Is video signal fed to pin 242 of IC3301 (Trident) via L.P.F. com-posed of Q2201 and Q2207?
Are Y and C signals fed to pins 242 and 231 of IC3301 (Trident) via L.P.F. composed of Q2201 and Q2207 and via L.P.F. com-posed of Q2205 and Q2209 respectively?
NO Check between SC1101and IC3301. (Q2201, Q2207, etc.)/(Q2205, Q2209, etc.)
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301?
NO Check IC3301 and peripheral circuits.
YESCheck LCD_CONTROL PWB.6 5
-
LC-32D41U/LC-32M41U/LC-40C32UNo video output during digital broadcasting reception
Is video signal sent to output terminal pin 4 of tuner (TU1101)? NO Check or replace the tuner's peripheral circuits.
YESIs video signal fed to pin 7 of IC1103 (LEVEL ADJ)? NO Is control signal for level adjustment fed from pin 1 of IC1104 to
pin 6 of IC1103?
YES
NOCheck or replace IC1104 (CONTROL) and peripheral circuits.
Is video signal fed to pin 244 of IC3301 (Trident) via L.P.F. composed of Q2204 and Q2208?
YES
NOCheck between IC1103 and IC3301. (Q2204, Q2208, etc.)
Are digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301?
NO Check IC3301 and peripheral circuits.
YESCheck LCD_CONTROL PWB.6 6
-
LC-32D41U/LC-32M41U/LC-40C32U No video output (3)
No video output from external input
Is INPUT-1 selected on the input switching menu screen? NO Select INPUT-1 and the input signal on the input switching menu
screen.
YES
When INPUT-1 cannot be selected since the characters INPUT-1 on the menu screen are gray.
Is the component video signal detection function normal? Check between pin 8 of J501 and pin 38 of IC501.
Are component video signals fed to pins 21, 23 and 25 (Y, PB and PR) of IC501(AV SWITCH)?
NO Check between J1501 and each input pin of IC501.
YESAre Y, PB and PR signals sent to pins 60, 59 and 58 of IC501 respectively?
NO Check IC501 and peripheral circuits.
YESAre component video signals sent to pins 2, 4 and 6 of IF_UNIT connector (FC_SC501)?
NO Check between IC501 and SC501. (Q501-Q506, etc.)
YESAre component video signals fed to pins 2, 4 and 6 of MAIN_UNIT connector (FC_SC1101)?
NO Check the board-to-board cable FC.
YESAre Y, Pb and Pr signals fed to pins 246, 232 and 225 of IC3301 (Trident) respectively?
NO Check between SC1101 and IC3301. (Q2202, Q2203, Q2206, etc.)
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301?
NO Check IC3301 and peripheral circuits.
YESCheck LCD_CONTROL PWB.6 7
-
LC-32D41U/LC-32M41U/LC-40C32UNo video output from HDMI input (INPUT3)
INPUT3Are signals fed from HDMI (SC1501) connector to input terminals H_RX0 (pins 51 and 52), H_RX1 (pins 54 and 55), H_RX2 (pins 57 and 58) and H_RXC (pins 48 and 49) of IC1507 (TMDS_SW)?
NO Is IC1501 (E2PROM) accessed with I2C when connecting HDMI device and is DDC_I2C_CLOCK/DATA data read out?
YES
YES
NOCheck IC1501 and peripheral circuits.Are cables connected securely?
Check the setting of HDMI device.
Are signals fed from IC1507 (TMDS_SW) to input terminals H_RX0 (pins 54 and 55), H_RX1 (pins 58 and 59), H_RX2 (pins 61 and 62) and H_RXC (pins 50 and 51) of IC1508 (HDCP_LSI)?
NO Check IC1507 (TMDS_SW) and peripheral circuits.For INPUT4, pin 21 is Low and pin 22 is High.For INPUT5, pins 21 and 22 are Low and pin
YESAre R/G/B and CLK/H/V/Data Enable signals sent from pins 92-96, 99-105,108-111, 114-117, 121-124, 119 and 127-129 of IC1508(HDCP_LSI)?
NO Check IC1508 (HDCP_LSI) and peripheral circuits.
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301(Trident)?
NO Check peripheral circuits of IC3301.
YESCheck LCD_CONTROL PWB.
When using an old HDMI transmission device, some video formats cannot be selected or no sound is heard. Since this model conforms to the latest HDMI standard, the HDMI transmission device does not recognize the data of the latest version correctly. It is necessary to upgrade its firmware. Download the latest firmware from the web site of each manufacturer, or contact the customer service center of each manufacturer.6 8
-
LC-32D41U/LC-32M41U/LC-40C32UNo video output from HDMI input (INPUT4)
INPUT4Are signals fed from HDMI (SC1502) connector to input terminals H_RX0 (pins 70 and 71), H_RX1 (pins 73 and 74, H_RX2 (pins 76 and 77) and H_RXC (pins 67 and 68) of IC1507 (TMDS_SW)?
NO Is IC1502 (E2PROM) accessed with I2C when connecting HDMI device and is DDC_I2C _CLOCK/DATA data read out?
YES
YES
NOCheck IC1502 and peripheral circuits.Are cables connected securely?
Check the setting of HDMI device.
Are signals fed from IC1507 (TMDS_SW) to input terminals H_RX0 (pins 54 and 55), H_RX1 (pins 58 and 59), H_RX2 (pins 61 and 62) and H_RXC (pins 50 and 51) of IC1508 (HDCP_LSI)?
NO Check IC1507 (TMDS_SW) and peripheral circuits.For INPUT4, pin 21 is Low and pin 22 is High.For INPUT5, pins 21 and 22 are Low and pin
YESAre R/G/B and CLK/H/V/Data Enable signals sent from pins 92-96, 99-105,108-111, 114-117, 121-124, 119 and 127-129 of IC1508 (HDCP_LSI)?
NO Check IC1508 (HDCP_LSI) and peripheral circuits.
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301 (Trident)?
NO Check peripheral circuits of IC3301.
YESCheck LCD_CONTROL PWB.
When using an old HDMI transmission device, some video formats cannot be selected or no sound is heard. Since this model conforms to the latest HDMI standard, the HDMI transmission device does not recognize the data of the latest version correctly. It is necessary to upgrade its firmware. Download the latest firmware from the web site of each manufacturer, or contact the customer service center of each manufacturer.6 9
-
LC-32D41U/LC-32M41U/LC-40C32UNo video output from DVI input (INPUT 5)
DIGITAL mode Analog modeAre signals fed from DVI (SC1503) connec-tor to input terminals H_RX0 (pins 8 and 9), H_RX1 (pins 11 and 12), H_RX2 (pins 14 and 15) of IC1507 (TMDS-SW)?
NO IS IC1505 (E2PROM) accessed with I2C when connecting HDMI device and is DDC_I2C_CLOCK/DATA data read out?
Are signal fed from pins 25, 26, 27 (Ana-log-R/G/B), and 28, 8 (H Sync/V Sync) of input terminal (SC1503) to pins 226, 248, 233, 10, 11 of IC3301 (Video PROCES-SOR)?
YES
YESNO
YESNO
Check IC1505 and peripheral cir-cuits.Are cable connected securely?
Check peripheral circuits of IC3301.
Check the setting of DVI Device. Check LCD_CONTROL PWB.
Are signals fed from IC1507 (TMDS_SW) to input termi-nals H_RX0 (pins 54 and 55), H_RX1 (pins 58 and 59), H_RX2 (pins 61 and 62) and H_RXC (pins 50 and 51) of IC1508 (HDCP_LSI)?
NO Check IC1507 (TMDS_SW) and peripheral circuits.For INPUT4, pin 21 is Low and pin 22 is High.For INPUT5, pins 21 and 22 are Low and pin
YESAre R/G/B and CLK/H/V/Data Enable signals sent from pins 92-96, 99-105,108-111, 114-117, 121-124, 119 and 127-129 of IC1508(HDCP_LSI)?
NO Check IC1508 (HDCP_LSI) and peripheral circuits.
YESAre digital video (LVDS) signals sent from pins 28-31 and 34-37 of IC3301 (Trident)?
NO Check peripheral circuits of IC3301.
YESCheck LCD_CONTROL PWB.
When using an old HDMI transmission device, some video formats cannot be selected or no sound is heard. Since this model conforms to the latest HDMI standard, the HDMI transmission device does not recognize the data of the latest version correctly. It is necessary to upgrade its firmware. Download the latest firmware from the web site of each manufacturer, or contact the customer service center of each manufacturer.
[FRONT-END SECTION]Digital broadcasting cannot be received.
Are US_TS_CLK/PKTSYNC/DATA sig-nal supplied to pin (51), (59), (66) of IC8601 respectively?
NO Are IF_OUT_P/N signal send from pin (20), (21) of TU1101 respec-tively?
YES Check IC8601 and its peripheral cir-cuits.
YES NOCheck the IC8101 and its peripheral cir-cuits.
Check the TU1101.6 10
-
LC-32D41U/LC-32M41U/LC-40C32ULEDflashingtimingchartforerrornotification
250ms
1sec
1)RedpowerLED
Remarks
Remarks
Remarks
Errortype
PowerredLEDoperation(1
cycle)
Errortype
PowerredLEDoperation(1
cycle)
Errortype
PowerredLEDoperation(1
cycle)
Pinsare
monitormicroprocessorpins.
H:On
Lampfailure
Flashesonce:Fast
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
H:On
L:Off
Referto
"Powerfailure
details".
Powerfailure
Flashestwice
communicationfailure
Referto
"Communicationfailure
details".
withmain
CPU
Communicationlinefailure
ormain
CPUcommunicationfailure
>Checkdebugstatements
forthemain
CPU.
Flashes3times
Vsync
Tridentfailure
Flashes4times
Monitortemperature
failure
Flashes5times
2)Powerfailure
details(PowerLEDflashestw
iceandOPCLEDflashes)
Pinsare
monitormicroprocessorpinsunlessotherw
isespecified.
13V/UR10Vfailure
Flashesonce
Main
3.3Vfailure
Flashestwice
UR6Vfailure
Flashes3times
Digital3.3Vfailure
Flashes4times
Panel5Vfailure
Flashes5times
Main
failure
Flashes7times
3)Communicationfailure
details(PowerLEDflashes3timesandOPCLEDflash
Initialcommunication
receptionfailure
Flashesonce
Tim
e-outse
ttingrece
ptio
nfailure
Start-up
confirm
ationrece
ptionfailure
Flashestwice
Regularcommunicationfailu
re
Flashes3times
Thedetails
are
displayedin
"ERRORSTANDBYCAUSE"onpage1ofprocessAmodeforthemain
microprocessor.
Initialcommunicationfrom
themain
CPUisnotreceived.(Aftercancelingthereset,requestforthemonitormodelNo.isnotreceived.)
Communicationlinefailure
ormain
CPUstart-upfailure
Tim
e-outsettingandstart-upmodechangecannotbereceivedfrom
themain
CPU.(Start-upcommunicationuntiltime-outsettingandstart-upmodechangeisnotreceived.)
Basically,communicationlogsare
analyzedbyabusmonitorordebugprintlogsare
analyzed.
Main
CPUstart-upfailure
ormonitormicroprocessor'sreceptionfailure
Regularcommunicationthatisperform
edat1secondintervalsin
thenorm
aloperationisinterrupted.
Main
CPUoperationfailure
ormonitormicroprocessor'sreceptionfailure
L_FL_ERR(pin
73):Abnorm
alL.Confirm
edafter5consecutivedetectionsat1secondintervals(detectedonlywhenthebacklightison).
Note
thatafterfivedetectioncounts,thelampcannotbeactivatedexceptin
themonitoringprocess.(Forthefirsttime,onlytheinverterisreset,anderrorOFFisnotactivated)
Accum
ulated
coun
tsareclea
redto
0whe
ntheco
rres
pond
ingse
tting
intheproc
essAismad
e,whe
nthepo
wer
isturned
onwith
[CH_D
OWN]a
nd[VOL_
UP]o
ntheun
itdo
wnor
afterco
ntinuo
usillum
inationfor3minutes
.
Main
microprocessordetectionerror(FANerror,1bitAMPerror,etc.
Iferrorisdetectedduringoperation,errorstandbyisactivatedbypolling.
DET_PNL5V(pin
57):Abnorm
al(L).Panelpowerisnotapplied.
Iferrorisdetectedduringoperation,errorstandbyisactivatedbypolling.
EU_POW
PS_ON
PANEL_POW
D_POW
D_POW
Iferrorisdetectedduringoperation,errorstandbyisactivatedbypolling.
DET_6V(pin
27):Abnorm
al
L).UR6Visnotapplied.
(MONITORMAXTEMPonprocessAmode:Changeoftemperature
failure
ADvalue):Therm
istor
DET_D3V3(pin
62):Abnorm
al
L).Digital3.3Visnotapplied.
Iferrorisdetectedduringoperation,errorstandbyisactivatedbypolling.
AC_DET(pin
31):Abnorm
al(L),DET_10V(pin
63).Main
converter13V/UR10Visnotapplied.
Iferrorisdetectedduringoperation,thepoweristurnedonagain
byinterrupthandling(instantaneousblackoutprocessing).
DET_3V3(pin
64):Abnorm
al(L).Main
power3.3Visnotapplied.
VSYNC(pin
48)failure
(uninput).Trident_IC
operationfailure.
Detectedduringoperation(interruption)
Ifthepaneltemperature
is60C
ormore
for15secondsormore
inarow,CAUTIO
Nappears
ontheOSDofAVC(flashesin
redin
thelowerrightscreen).
Ifthepaneltemperature
is60C
ormore
for25secondsormore
inarow,errorstandbyisactivated.
6 11
-
LC-32D41U/LC-32M41U/LC-40C32U
7 1
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 7. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS IC8101 (RH-iXB145WJQZQ)
An LSI of a MPEG-2 system decoder that performs back-end processing for digital broadcasting. This is equipped with a CPU (processor core:AM33-3), descrambler (DES), transport stream demultiplexer, video decoder (MPEG-2 MP @ HL compatible), graphic processor, audio decoder(AC3 compatible), and an NTSC video encoder.
After receiving transport stream from the tuner, the LSI decrypts pay-TV broadcasts with the descrambler. Then using the demultiplexer, it sepa-rates and decodes the compressed audio and video data to send the signals. In the visual system, the graphic processor makes it possible tooverlap subtitles and perform scaling. Digital video signals (Y, Pb and Pr, or 480I/P, 720P and 1081I) and downconverted NTSC signals (Y/C andcomposite, or 480I) can be sent simultaneously. As for the audio system, decoded AC3 audio can be overlapped with sound effects.
The LSI also contains various interfaces (I2C x 2, UART x 3, an SD Memory Card interface, a CableCARD interface, etc.) and a GPIO. Usingthese interfaces, the CPU controls peripheral circuits of the tuner, SD Memory Cards, CableCARDs, etc. One of the UARTs is used by the CPU toestablish communications with the monitor microcomputer in the unit, where remote control information or other data is exchanged. Another UARTis used for RS-232C serial communications to connect the unit to a PC.
-
LC-32D41U/LC-32M41U/LC-40C32U
POWERUNIT
AC IN
LA
SP-R
INVERTERUNIT
QCNW-E847WJQZ
LALC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 8. OVERALL WIRING/BLOCK DIAGRAM
[1] OVERALL WIRING DIAGRAM
A
C
B
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10
PE
80 1 80 1
1
KMLV SH
1
6
SP
RA
1
12
71
7 1
1
2
IF UNIT
MAIN UNIT
LCD CONTROL UNIT
KMKEY UNIT
QCNW-E257WJQZ
QCNW-E273WJQZ
QCNW-E258WJQZ
U/VTUNER
HDMI
R-AUDIO-LINPUT 4
S-VIDEO
1 4
QCNW-E285WJQZ
DIGITAL AUDIOOUTPUT
4 1
6
1
PE12
1
QCNW-E266WJQZ
132
PD
QCNW-E703WJPZ
P9701
P2703
P9702
P2002
RALED UNIT
11 1P101
P151
CN1 CN2
J503
J501
J502
SC1501
11 1
SC1502
P502
1 23 1 23 1 23
1 23 1 23 1 23SC1102 SC1101 SC1301
SC502 SC501 P2704
P2601
SH
LV
P2602
1 4
PD
CN5701
CN5702
LB
P2603
QCNW-E259WJQZ
ANTIN
HDMI
AUDIOOUTPUT
INPUT 2
INPUT 1
INPUT 3
INPUT 4
D1402
J1501
SCSC8
SD
SP-L
J1502DVIAUDIO INPUT 5
SC150DVI-IINPUT 5
TU1101
QCNW-E249WJPZ (LC-32D41U/LC-32M41U)
QCNW-E442WJPZ (LC-40C32U)8 1
-
LC-32D41U/LC-32M41U/LC-40C32U
PE
KMLV
SP
RA
IF UNIT
MAIN UNIT
LCD CONTROL UN
KMKEY UNIT
QCNW-E257WJQZ
QCNW-E273WJQZ
QCNW-E258WJQZ
U/VTUNER
HDMI
R-AUDIO-LINPUT 4
S-VIDEO
QCNW-E285WJQZ
DIGITAL AUDIOOUTPUT
PE
QCNW-E266WJQZ
PD
QCNW-E703WJPZ
RALED UNIT
SH
LV
P
LB
QCNW-E259WJQZ
ANTIN
HDMI
AUDIOOUTPUT
INPUT 2
INPUT 1
INPUT 3
INPUT 4
SD
SP-L
DVIAUDIO INPUT 5
DVI-IINPUT 5
QCNW-E249WJPZ (LC-32D41U/LC-32M41U)
QCNW-E442WJPZ (LC-40C32U)10 11 12 13 14 15 16 17 18 19
1
SH
7 1
POWERUNIT
IT
AC IN
LA10
1
SP-R
INVERTERUNIT
To LAMP
To LAMP
To LAMP
To LAMP
To LAMP
To LAMP
To LAMP
To LAMP
QCNW-E847WJQZ
CN3
CN5703
CN2
D
1
2
LA
114
8 2
-
LC-32D41U/LC-32M41U/LC-40C32U
[2] SYSTEM BLOCK DIAGRAM
A
C
B
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10
SP_MUTESP_RELAYL_MUTEAMP_MUTEHDMI_MUTESTANDBY
SLOW
BUS
MAIN
SA SC130123PinP2704
PH1IC8
IXB14
Digital AV deco
I2C0
SLOW B
TS
SPP2703 4Pin
EEPROMIC8454BR24L64F
CVBS
YPbPr
IF
HDMI 2
CVBS
S
HDMI_L/R
HDMI_YPbPr
TS in
DTV/I2S
DTV/SPDIF
TS
SIF
IC501AV SWITCHMM1630CQ
TVMainOut
Video1
Video2
AUDIO CODECIC1403
AK4683EQ
SOUND DSPIC1406
NJU26111
HDMI_SPDIF
IC2701Digital AMPTA2024
SP_L/SP_R
RELAY
HDMI RXIC1508SiI9011L
RX0
OUT1
OUT2
SDTOA
SDTIA2
SDTIA3
TX
HDMI 1
IC3301IXB405WJ
Video Processor
14.318MHzXtal
LVDS OUT
Digital IN
CVBS1
(IX
CVBS2(Y)
C
YCbCr
I2C
+3.3V +1.8V+2.5V
+2.5V
Main Y/V
Main C/Cb
Main Cr
Comp_Cb
Comp_Cr
Comp_Y
Y
C
Y/V
C
+9V_A
CK,HD,VD
RF IN
Analog/DigitalTunerTU1101
AA004WJQZ
DemodulatorIC8601
IXB684WJQZ
I2C1
D_IF
AGC
IC9101CPLD
IXB685WJ
+3.3V
OPTICALOUT
Monitor Out
TMDSSelectorIC1507
TMDS341
DDR
CK,HD,VD
TUN_I2C
+3.3V
FLASH 64MbIC8451
S29GL64A
AMP(in IF Unit)
CVBS1_A
RX_x8
RX_x8
L/R
I2C_0
I2C_1I2C1_S
(400KHz)
+3.3V
+3.3V
+3.3V
SIF DecoderIC1401
AN5832SA
AFT
3-5VConv
CVBS/LR
Component
CVBS/LR
S Video
HDMI Audio
INPUT1
INPUT2
INPUT4
INPUT3
INPUT4
L/R
L/R
RX1
SDTIB
EEPROMEEPROM
RESET
Xtal27MHz
27MHz
74MHz
83.5MHz
14.318MHz
164MHz
DTV_SPIDF
DTV_I2S
IF to MAIN I/F
IFto
MAIN
I/F
I2C0_5
I/O ExpanderIC1301
M62320FP
+5V
(100KHz)
(100KHz)
+3.3V
CVBS3TUNER_V
SC502 23Pin
SC50123Pin
DiscreteLPF
IN1Tuner L/R
IN2IN1_L/R
IN3
IN5HDMI_L/R
IN3_L/R
BUS SWIC9201
IXB011WJ
HDMI_YPbPr
N_CPU_RST
CLOCKCLK_GenIC8401
IXB422WJ
5-3VConv
5-3VConv
I2C
I2C
I2C
SC1102
SC1101
5-3VConv
DVII2C
RX_x8
INPUT5
EEPROM
DVI AudioINPUT5
IN4
DVI_L/R
DVI_L/R8 3
-
LC-32D41U/LC-32M41U/LC-40C32U10 11 12 13 14 15 16 17 18 19
CBOOT
N_SRESET
LV
P2601
32Pin
LVDS
POWER
SD CARD
PH1_LiteIC8101
IXB145WJQZ
Digital AV decode & Main CPU
SLOW BUS
YUVout
AC IN
80FFC
80FFC
KEY
KM P2002 4PinP151
LCDPANEL
LA CN570310Pin
BL
LCD
PNL+5V
+24V
Thermistor
PNL+5V
KEY1,KEY2
Standby
InverterPFC
MAIN
BU5 v
24 v
AC
10v
PS_ON
UR +13vPNL-POW
SMPOWHOLD
+10V
BU+5V
VON
SH
P2602
7Pin
PE
P9701
12Pin
CN5701
RA P101 11Pin
LED
OPC_LED,POW_LED_G
R/COPCLED
AREADetect
CK,H
D,VD
SD
CARD
n
I2S
SPDIF
DDRIC8301
IXB667WJQZ256Mb
or
LVDS OUT
IC3302DDR
(IXB375WJ)128Mbit
I2C
+2.5V
CPUH8
UART
A/DAREA1,3
BU+3.3V
R/L,U/D
TEMP [3:1], O_S_SET, FRAME, ROMSEL0
10MHzXtal
Power Supply Circuit
Main System+A5V+A9V+5V+3.3V+2.5V+1.8V_VL+1.2V+1.0V_ATIPNL_5V
DDR
I2C
I2C1_SCL/SDA
ERR_PNL
IC2004EEPROMBR24L08F
DET_10V,DET_3V3,DET_6V,DET_PNL5V
I/O
STBY_POW
IC2005DAC
M62332FP
I/O
I/O
I/O
AC_DET
VBRT
I/O
I/O
I/O
BU+5V
QSTEMPA/D
OPC
A/D
R/C
V
+2.5V
I2C_0
I2C_1
(400KHz)
SW
+3.3V
AMP+13V
Backup SystemBU+3.3VBU+5V
PM_REQ
I/O
LINK_POW
I/O
I/O
ET
83.5MHz
Hz
164MHz 10MHz
RA P502 11Pin
Through IF Unit
(100KHz)
UR+6V
(PNL 5v)
BU+3.3V
R/L,U/D
VON
BU+3.3V
ERR_L
LB
P2603
4Pin
I/O
Panel SizeDetect
PSIZ_L,HI/O
CHK15VI/O
PD
P9702
6Pin
CN5702SM_POW,D_POW PS_ON,D_POW
EXT_SMPOWHOLD
HOLD
BU+3.3V
AND
PNL_POW
PANEL_POWI/O
A/D
PNL5V_ON_PH1
I/O
UARTTxD_PH1,RxD_PH1
From PH1
From CPLD
AFT
DDRIC8302
IXB667WJQZ256Mb
DDR
I/OI/O
OCK
Inverter Circuit
INVERTER
LA CN314Pin
POWER
INPUT
TUNE
VOLUME8 4
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U/LC-32M41U/LC-40C32U Service Manual CHAPTER 9. PRINTED WIRING BOARD ASSEMBLIES
[1] MAIN Unit LC-32D41U
A
C
B
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10
MAIN Unit (Side-A) (LC-32D41U)9 1
-
LC-32D41U/LC-32M41U/LC-40C32U
10 11 12 13 14 15 16 17 18 199 2
-
LC-32D41U/LC-32M41U/LC-40C32U
LC-32D41U
A
C
B
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10
MAIN Unit (Chip Parts Side-A) (LC-32D41U)
LUG1104
k1
k2
R1555
R1559
D1514
R1633
R1501
Q1506
Q1508
R1502
SC1501
L1506
C1537
L1507
IC1506
L1508
L1509
R1551
C1536
D1511
FB1516
C1518
D1501
R1557
C1520
R1516
Q1505
Q1507
C1552
Q1501
Q1502
R1619
IC1509
R1632
R1634
R1636
R1520
IC1510
C1585
R1616
R1611
C1635
R1625
C1596
R1505
C1599
C1551
R1519
C1563
SC1502
C1543
R1609C1562
L1510
R1607
C1544
R1599
R1608
L1511
R1600
R1614C1564
L1512
C1565
IC1507
L1513 C
1549
C1550
C1556
R1595
R1601
R1606
TP1502
R1618
FB1517 C1541
C1540
VA1505
L1503
VA1508
VA1507
L1504
VA1506
VA1504
L1502
VA1503
VA1501
L1501
VA1502
P9301
R1525
C1521
D1507
FB1505
R1528
SC1503
R1526
D1508
R9303
R9304
FB1509
R9306
R1571
IC1503
L1505
R1529
R1561
C1522
C1638
C1524
C1523
R1513
Q1509
R1573
D1512
C1641
FB1507
C1525
R1563
R1577
R1568
R1548C1526
R1562
C1639
FB1508
C1527
Q1510
R1574
R1564
R1565
R1549C1528
R1578
R1569
FB1506
C1529
C1640
R1566
Q1511
R1575
R1550C1530
R1567
R1570
R1579
C8507
C8509
C8537
C8504
IC8502
IC8501
FB8503
C8503
FB8502
R2053
FB8501
C8501
C8502
C8512
C8508
J8501
R8503
C8516
C8517
R8510
R8511
R8514
IC2006
R8509
C8518
L8501
C8511
C8520
C8513
C8522
R8513
R8518
C8510
R8519
C8515
C8523
R8517
C8514
C8525
L8502
R8522
C2023
C8526
R8529
R2058
R2045
R8532
R8564
C8528
R8538
R8535
C8529
R2057
R8545
R8562
R8567
R8542
R8571
C8530
R8541
R8558
C8532
J8502
C8534
C8531
R8569
C8533
R
R8572
R2070
R8550
R857
L8
C8116
R
R
R20
C8123
TP8
R8154
C8122
D2003
TP2
R8155
TP2013
R2041
R2050
TP2012
C2013
C2016
R9224
TP2011
R2042
R2054
R2056
R2055
R8113
R2048
C2017
C2018
TP2014
R2071
R2049
R2043
R2044
R2047
R2046
C2020
R2062
R2060
R2061
R2063
IC9201
R2066
C2022
R2064
R2059
R9225
R8115
C9202
IC2005
IC2004R9226
IC2003
R9230
C2021
C2019
C2025
R9227
R2005
R9228
R9229
FL9201
R2065
R9302
C8314
C8318
TP9106
R8338
TP9103
TP9101
P9101
R9124
R9105
R9111
C9103
R9305
R9106
R9115
C9102
R9301
TP9102
P2001
X1501
C1617
R1612
C1620
FB1520
R1627
R1617
R1635
C1604
C1600
C1612
C1610
R1610
C1590
C1588
R1603
R1613
R1615
R1626R1631R1630
IC1508
R1629R1628
C1560
C1561
C1598
C1595
C1605
C1603
C1619
C1618
C1622
C